GC8200 Series
Contents
1. Too much scale and minerals have accumulated inside the steam generator You have not tightened the Calc clean rinsing cap properly Solution Place the water tank properly in the steam generator click Set the iron to a lower temperature e g to check if the iron actually produces steam Set a temperature of ee or higher This is normal When you start ironing or when you continue ironing after an interruption hold the iron over an old cloth and press the steam trigger Wait until steam instead of water comes out of the soleplate Clean the soleplate with a damp cloth This is normal Unplug the iron immediately and contact an authorised Philips service centre Set the steam lock to off if you only want to obtain steam when you press the steam trigger see section Steam lock function Rinse the steam generator See chapter Cleaning and maintenance Switch off the appliance tighten the Calc Clean rinsing cap and switch on the appliance again If steam continues to escape when the appliance is heating up switch off the appliance and contact a service centre authorised by Philips Problem The iron does not produce enough steam the amount of steam decreases and increases during steam ironing Wet spots appear on the fabric during ironing GC8325 GC8320 GC8261 GC8260 GC8225 GC8220 only Water droplets come out of the soleplate when use the shot of st2. Filling the detachable water tank Wait approx 2 minutes GC8325 GC8320 GC8261 GC8260 GC8225 GC8220 only wait until the steam light stays on continuously Set a temperature of ee or higher Set steam setting minimum steam moderate steam or maximum steam 16 ENGLISH Problem Water droplets come out of the soleplate Flakes and impurities come out of the soleplate or the soleplate is dirty The appliance produces a pumping sound The iron produces steam continuously Dirty water comes out of the soleplate Steam escapes from under the Calc Clean rinsing cap when the appliance heats up Cause You have not placed the water ank properly in the steam generator When the iron is set to a very high emperature the steam produced is dry and hardly visible It is even less visible when the ambient temperature is relatively high and it is entirely invisible when the temperature is set to MAX The set temperature is too low for steam ironing When you start steam ironing and when you stop steam ironing for a while the steam still present in the supply hose cools down and condenses into water This causes water droplets to come out of the soleplate Impurities or chemicals present in the water have deposited in the steam vents and or on the soleplate Water is pumped into the steam generator The pumping sound does not stop The steam lock has been set to on
3. W Steam generator control panel with steam light GC8325 GC8320 GC8261 GC8260 GC8225 GC8220 only maximum steam moderate steam minimum steam 2 no steam X On off switch with power on light GC8210 only Important Read this user manual carefully before you use the appliance and save it for future reference YD OVOZZFAI ATMIONDD lt ca Danger Never immerse the iron or the steam generator in water ENGLISH 7 Warning Check if the voltage indicated on the type plate corresponds to the ocal mains voltage before you connect the appliance Do not use the appliance if the plug the mains cord the supply hose or he appliance itself shows visible damage or if the appliance has been dropped or leaks Ifthe mains cord or the supply hose is damaged you must have it replaced by Philips a service centre authorised by Philips or similarly qualified persons in order to avoid a hazard ever leave the appliance unattended when it is connected to the mains This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for heir safety Children should be supervised to ensure that they do not play with the appliance Do not let the mains cord and supply hose come into contact with the
4. hot soleplate of the iron If steam escapes from under the Calc Clean rinsing cap when the appliance heats up switch off the appliance and tighten the Calc Clean rinsing cap If steam continues to escape when the appliance heats up switch off the appliance and contact a service centre authorised by Philips ever remove the Calc Clean rinsing cap when the steam generator is hot Do not use any other cap on the steam generator than the Calc Clean rinsing cap that has been supplied with the appliance as this cap also functions as a safety valve Caution Only connect the appliance to an earthed wall socket Check the mains cord and the supply hose regularly for possible damage Always place and use the iron and the steam generator on a stable level and horizontal surface The soleplate of the iron can become extremely hot and may cause burns if touched When you have finished ironing when you clean the appliance when you fill or empty the water tank and also when you leave the appliance even for a short while put the iron on the iron stand switch off the appliance and remove the mains plug from the wall socket Rinse the steam generator regularly according to the instructions in chapter Cleaning and maintenance This appliance is intended for household use only Electromagnetic fields EMF This Philips appliance complies with all standards regarding electromagnetic fields EM
5. F If handled properly and according to the instructions in this user manual the appliance is safe to use based on scientific evidence available today 8 ENGLISH Before first use Note The iron may give off some smoke when you use it for the first time This is normal and stops after a short while Note Some particles may come out of the soleplate when you use the iron for the first time This is normal the particles are harmless and stop coming out of the iron after a short while Note When you switch on the appliance the steam generator may produce a pumping sound This is normal the sound tells you that water is pumped into the steam generator Remove any sticker or protective foil from the soleplate and clean the soleplate with a soft cloth Preparing for use Place the steam generator on a stable and level surface e g on the hard part of the ironing board or on a table Filling the detachable water tank You can fill the water tank at any time during use Do not put hot water perfume vinegar starch descaling agents ironing aids or other chemicals in the water tank Do not overfill the water tank otherwise water may spill out of the filling opening when you reinsert the water tank Remove the detachable water tank from the steam generator Fill the water tank with tap water up to the MAX indication Note If the tap water in your area is very hard we advise you to mix it with an equal amount of dis
6. Register your product and get support at www philips com welcome GC8200 Series PHILIPS flit Philips GC8300 GC8200 Series ENGLISH 6 INDONESIA 18 501 30 BAHASA MELAYU 42 mun Ina 55 BAHR 65 6 ENGLISH Introduction Congratulations on your purchase and welcome to Philips To fully benefit from the support that Philips offers register your product at www philips com welcome The powerful pressurised ironing system produces non stop steam to make ironing easier Thanks to the large water tank you can iron without interruption When the water tank is empty you can detach it and refill it immediately We hope you enjoy using this ironing system General description Fig 1 Supply hose Handle GC8261 GC8260 only with soft grip Temperature dial Steam trigger Temperature light Steam lock Shot of steam button GC8325 GC8320 GC8261 GC8260 GC8225 GC8220 only Soleplate Safe storage lock GC8261 GC8260 only Iron stand Detachable water tank Cord amp hose storage hook Calc Clean rinsing cap Filling opening Water tank release lever Steam generator On off button with power on light GC8325 GC8320 GC8261 GC8260 GC8225 GC8220 only Transport handgrip Water tank refill light GC8325 GC8320 GC8261 GC8260 GC8225 GC8220 only Calc Clean light GC8325 GC8320 GC8261 GC8260 only Mains cord Steam buttons GC8325 GC8320 GC8261 GC8260 GC8225 GC8220 only
7. cur To prevent this use a dry pressing cloth or turn the article inside out and iron the reverse side Silk woollen and synthetic materials iron the reverse side of the fabric to prevent shiny patches Iron velvet and other fabrics that tend to acquire shiny patches in one direction only along with the nap while you apply very little pressure Do not use steam when you iron coloured silk This could cause stains 12 ENGLISH Cleaning and maintenance After ironing Put the iron on the iron stand see chapter Storage and switch off the appliance Remove the mains plug from the wall socket and let the appliance cool down Wipe scale and any other deposits off the soleplate with a damp cloth and a non abrasive liquid cleaner Clean the upper part of the iron and the outside of the steam generator with a moist cloth Empty the water tank after cleaning Calc Clean function Never remove the Calc Clean rinsing cap when the steam generator is hot VERY IMPORTANT Rinse the steam generator once a month or after every 10 times of use to prevent damage to the appliance and for optimal steaming performance EN Unplug the appliance and let it cool down for 2 hours Remove the detachable water tank Hold the steam generator with both hands and shake well Turn the steam generator on its side with the Calc Clean rinsing cap facing upwards and remove the Calc Clean rinsing cap ENGLISH 13 Empty the stea
8. eam function Cause When the appliance the steam generator sometimes decreases This is probably when you think that pumps water into the steam amount he iron does not produce enough steam However this is a normal phenomenon and the steam output normalises within a few seconds The wet spots that appear on the fabric after you have steam time may be caused by steam that has condensed onto the the wet spots withou ironed for some ironing board Iron it steam for some time to dry them If the underside of the ironing board is wet wipe it with a piece of dry cloth Steam may have condensed in the hose the temperature may have been set below eee or the appliance may not be ready for steam ironing ENGLISH 17 Solution To optimise the steam output release the steam lock when you do not need steam and when you put down the iron To prevent steam from condensing onto the ironing board use an ironing board with a wire mesh top Make sure the temperature is set to eee or higher Steam iron for a few seconds before you use the shot of steam function
9. he steam generator is ready for steam ironing GC8210 only Set the on off switch to on D The power on light in the on off switch goes on Dd The temperature light on the iron goes on When the iron has reached the set temperature the temperature light goes out Note During ironing the temperature light goes on from time to time This indicates that the iron is heating up to the set temperature Dd After approx 2 minutes the steam generator is ready for steam ironing Tips If you do not know what kind or kinds of fabric an article is made of determine the right ironing temperature by ironing a part that is not visible when you wear or use the article Ifthe fabric consists of various kinds of fibres always select the temperature required by the most delicate fibre i e the lowest temperature For example if a fabric consists of 60 polyester and 40 cotton it must be ironed at the temperature indicated for polyester and without steam Start ironing the articles that require the lowest ironing temperature i e those made of synthetic materials If you set a lower temperature during ironing wait until the iron has cooled down to the set temperature before you continue ironing To make the iron cool down faster simply press the steam trigger or iron a piece of cloth 10 ENGLISH Using the appliance Steam ironing The supply hose may become hot during a long ironing session Note The system ma
10. ilips website at www philips com or contact the Philips Consumer Care Centre in your country you find its phone number in the worldwide guarantee leaflet If there is no Consumer Care Centre in your country go to your local Philips dealer Problem The appliance does not become hot Troubleshooting This chapter summarises the most common problems you could encounter with the appliance If you are unable to solve the problem with the information below contact the Consumer Care Centre in your country Cause There is a connection problem You have not switched on the appliance The set temperature is too low Smoke comes out of Some parts of the appliance have been my new iron when switch it on The iron does not produce any steam lightly greased in the factory and may tank sufficiently The set ironing temperature is too low for steam ironing GC8325 GC8320 GC8261 GC8260 GC8225 GC8220 only You have set steam setting no steam initially give off some smoke when heated There is not enough water in the water The steam generator has not heated up Solution Check the mains cord the plug and the wall socket GC8325 GC8320 GC8261 GC8260 GC8225 GC8220 Press the on off button GC8210 set the on off switch to on Set a higher temperature This phenomenon is normal and ceases after a short while Fill the water tank See chapter Preparing for use section
11. lows you to steam iron non stop without having to press the steam activator continuously When you slide the steam lock forwards the iron produces steam continuously To stop steaming slide the steam lock backwards When the steam lock is deactivated the iron only produces steam when you press the steam trigger Note Release the steam lock when you put the iron on its heel or on the iron stand This prevents that hot steam escapes from the iron or that the iron stand gets wet A A 7 a LE ENGLISH 11 Vertical steaming Never direct the steam at people Hold the iron in vertical position and press the steam trigger to steam iron hanging curtains and clothes jackets suits coats Shot of steam GC8325 GC8320 GC8261 GC8260 GC8225 GC8220 only A powerful shot of steam helps to remove stubborn creases Set the temperature dial to a position between eee and MAX Press the shot of steam button Note Use the shot of steam function intermittently If water droplets come out of the soleplate let the iron heat up for at least one minute before you use the shot of steam function again Ironing without steam There are one or two ways to iron without steam All types Simply start ironing without pressing the steam trigger GC8325 GC8320 GC8261 GC8260 GC8225 GC8220 only Select steam setting no steam and start ironing Tips When you steam iron woollen fabrics shiny patches may oc
12. m generator into the sink IA Fill the steam generator with fresh water and shake again Empty the steam generator into the sink again EJ Repeat steps 6 amp 7 twice to obtain the best result El Screw the Calc Clean rinsing cap tightly back onto the steam generator Calc Clean light GC8325 GC8320 GC8261 GC8260 only The Calc Clean light flashes for 30 seconds when it is time to rinse the steam generator The steam generator does not heat up during these 30 seconds Switch off the appliance immediately and let it cool down Do not use the Calc Clean function when the steam generator is hot Use the Calc Clean function as described above 14 ENGLISH Storage Always let the appliance cool down before you store it GC8261 GC8260 only Insert the tip of the iron into the safe storage lock on the stand GC8261 GC8260 only Press down the back of the iron firmly click Empty the water tank Pull out the cord amp hose storage hook Secure the supply hose and mains cord IA To move the appliance carry it by the handgrips on either side of the steam generator Environment ENGLISH 15 Do not throw away the appliance with the normal household waste at the end of its life but hand it in at an official collection point for recycling By doing this you help to preserve the environment Guarantee amp service If you need service or information or if you have a problem please visit the Ph
13. tilled water Slide the water tank firmly back into the steam generator click Note If the water tank is not properly placed the iron does not produce any steam Water tank refill light GC8325 GC8320 GC8261 GC8260 GC8225 GC8220 only When the water tank is empty the water tank refill light starts flashing and steam ironing is no longer possible EB Remove the water tank and fill it Put the water tank back into the steam generator The iron is ready for steam ironing again ENGLISH 9 Setting the temperature Check the laundry care label of the article to be ironed to determine the required ironing temperature for synthetic fabrics e g acrylic viscose polyamide and silk for wool 0086 for cotton MAX for linen To set the required ironing temperature turn the temperature dial to the appropriate position Put the mains plug in an earthed wall socket Switch on the appliance GC8325 GC8320 GC8261 GC8260 GC8225 GC8220 only Press the on off button once The power on light of the on off button goes on D The temperature light on the iron goes on When the iron has reached the set temperature the temperature light goes out Note During ironing the temperature light goes on from time to time This indicates that the iron is heating up to the set temperature D The steam light starts flashing After approx 2 minutes the steam light stays on continuously to indicate that t
14. y occasionally produce a pumping sound during steam ironing This is normal and tells you that water is pumped into the steam generator Make sure there is enough water in the water tank Make sure the appliance is plugged in and switched on see chapter Preparing for use Set the required ironing temperature see chapter Preparing for use Steam ironing is only possible at ironing temperatures higher than e e GC8325 GC8320 GC8261 GC8260 GC8225 GC8220 only Set the required steam setting with the and buttons on the steam generator control panel for maximum steam temperature setting MAX Ee for moderate steam temperature settings eee to MAX ZS for minimum steam temperature settings ee to MAX A 2 for no steam temperature settings e to MAX D The steam light flashes to indicate that the steam generator is heating up Dd After approx 2 minutes the steam light stays on continuously to indicate that the steam generator is ready for steam ironing Note During ironing you can adjust the steam setting with the and steam buttons It takes a few moments before the amount of steam is adjusted O Press the steam trigger to start steam ironing When you put down the iron during ironing put it on its heel or on the cud iron stand D The opening and closing of the steam valve in the steam generator causes a clicking sound This is normal Steam lock function The steam lock al
Download Pdf Manuals
Related Search