Edge Diving System installation manual - Inter-Fab
Contents
1. EDGE DIVING SYSTEM aquaBoard Supplemental Installation Guide You MUST ine to the Edge Diving System installation manual for proper jig placement locations minimum diving envelope requirements and installation information Refer to these instructions only when using a 6 or 8 foot Edge aquaBoard together with a Board Fall water feature 1 WATER STUB UP DETAILS If installing a BOARD FALL or lighted waterfall feature ensure that a 1 2 minimum water stub up and when applicable an electrical conduit is located within the area designated Fig 7 Provide a minimum of 10 gallons per minute water flow for the BOARD FALL water feature Ensure electrical conduit wiring and transformer installations comply with local or national electrical codes whichever is greater NOTE Maximum water supply is 1 1 2 PVC To ensure all plumbing and electrical conduit will not hit the inside of the base the stub up must not exceed 4 in height 2 BOLT HEIGHT DIVING BOARD AROVE DECK DECK END WATER END NG BOLT PATTERN 11 HOW L F f ih Wh j AA i C Oi SA C y ye 5 l j DECK LENGTH amp MIN WA Fig 1 DECK THICKNESS 6 MAIM DECK WIDTH 4 MINI toward pool gt 2 BOARD FALL DETAILS The BOARD FALL water feature is available in 3 styles described below Each style will work with a 6 or 8 foot Edge aqguaBoard NOTE Minimum 10 GPM water supply recommended Please see detailed installation instructions f2. ng system Simply thread the wiring attached to your waterfall lighting system down the channel in the center of the board along side the 1 2 PVC tubing TIP You may find it simpler to put end of wire into end of hose or tape the wiring to the end of the 1 2 flex PVC and thread them thru the conduit at one time The LED lighting system comes with 10 of wire attached to the LED which goes through the board and attaches to the coupler the additional 25 of wiring attaches to the coupler and then passes through the customer installed conduit to the color controller The fiber optic lighting comes with 55 of continuous cable which is passed through the board then through the customer installed electrical conduit to the customer provided color light source C Once the water tubing and wiring are threaded all the way through the diving board from the base side gently pull the end of the tubing until the waterfall assembly is pulled gently into the BOARD FALL receiver on the top of the diving board D Mark the hole locations for attaching the BOARD FALL unit to the board For an Edge aquaBoard Locate the BOARD FALL unit all the way to the back of the BOARD FALL receiver Fig 2 Make sure the hose is threaded through the channel as shown Fig 3 Using a 1 8 drill bit drill the 4 holes 1 2 deep Use tape to mark the drill bit depth IMPORTANT Do not drill the holes deeper than 1 2 as there is a risk of drilling all the
3. or dive stand installation information and requirements BOARD FALL CONFIGURATIONS 1 BOARD FALL kit includes Board Fall Mounting Hardware 4 screws 8 amp 4 of 1 2 Flex PVC Pipe 1 Union 2 BOARD FALL L kit includes Board Fall parts PLUS LED Lights Assembled RGB Color Controller 35 of Wire 10 on unit 25 on controller Coupler NOTE No transformer is provided 3 BOARD FALL F kit includes Board Fall parts PLUS 55 of 25 Strand Fiber Optic Cable Assembled NOTE No light source is provided STEP ONE INSTALL BOARD FALL WATER FEATURE ON EDGE aquaBoard If purchased attach the optional waterfall assembly to the underside of the Edge aquaBoard as follows IMPORTANT To keep the BOARD FALL from clogging when installing on a Sand Filter System an in line cartridge filter is recommended on the BOARD FALL water supply line A The BOARD FALL comes from the factory with an amp length of 1 2 flex PVC pipe attached The 8 length goes thru the board and attaches with PVC glue to one side of the 1 2 union The 4 length of flex PVC pipe attaches with PVC glue to the stub up and then to the other side of the 1 2 union continued gt Jncer fau 800 737 5386 5 ANERNON way EDGE AB SUPP IM Rev 10 10 BBK LM INSTALL 1 12 00 EDGE aquaBoard SUPPLEMENTAL INSTALLATION GUIDE B If purchased your BOARD FALL waterfall comes with an optional pre wired factory installed LED or Fiber Optic lighti
4. way through the board Edge aquaBoard m Edge aquaBoard Fig 2 Fig 3 E Attach the waterfall unit to the Diving Board by inserting the 4 provided screws thru the holes in the waterfall assembly hand tighten only DO NOT USE SCREW GUN over tightening the screws will cause them to strip inside the board or break the waterfall housing and voids the warranty WARNING Do not attach the color controller directly to 110V the LED lighting is a low voltage system requiring a transformer not included to provide power to the color controller Inter Fab recommends the Intermatic PX100 transformer If the Intermatic PX100 is not utilized the color controller Input Rating is 12 VAC 1 7 Amp 60 50HZ Exceeding the input rating will severely damage the color controller and void the warranty 3 BASE PLUMBING ELECTRICAL DETAILS Remove the black cap on the top of the base Fig 4 Pass the hose through the base Fig 5 Coil up any excess hose under the base Fig 6 Edge aquaBoard Edge aquaBoard Fig 4 EDGE AB SUPP IM Rev 10 10 BBK LM INSTALL 2
Download Pdf Manuals
Related Search