User Manual in English
Contents
1.2. exceeded 3000 riding hours and the battery is empty Check speed is displayed Make sure your speed sensor is positioned correctly Rotate the wheel a few times to activate the sensor The flashing red light indicates that the sensor is activated Also the battery of your speed sensor may be empty For futher information see Care and Maintenance Sensor not Found and Try again are displayed Press OK to start seeking here are irregular speed distance or heart rate readings Electromagnetic interference as well as interference from other wireless training computers may affect readings of speed distance and heart rate Disturbances may occur near high voltage power lines traffic lights overhead lines of electric railways electric bus lines or trams WLAN base stations car motors bike computers some motor driven exercise equipment cellular phones or when walking through electric security gates Technical Specification Operating 10 C to 50 C 14 F to temperature 122 F Battery life Average 3000 riding hours Accuracy 1 Material Thermoplastic polymer Water resistance Splash proof ENGLISH Limited Polar International Guarantee This limited Polar international guarantee is issued by Polar Electro Inc for consumers who have purchased this product in the USA or Canada This limited Polar international guarantee is issued by Polar Electro Oy for consumers who have purchased this p
3. firmly Cut off any excess cable tie ends picture 2 3 Position the training computer on to the sulky mount Turn the training computer clockwise until you hear a click You can release the training computer by pressing it down and simultaneously turning it counter clockwise Installing the Polar Speed Sensor To install the speed sensor and spoke magnet you will need cutters and a cross head screwdriver 1 It is recommended to install the speed sensor on the fork as in picture 1 of your sulky ENGLISH 2 Attach the rubber part to the speed sensor picture 3 3 Pass the cable ties over the speed sensor and rubber part picture 4 Adjust the sensor to the fork so that the POLAR ogo faces outwards Adjust the ties loosely Do not tighten them fully yet 4 Attach the magnet to a spoke at the same evel as the speed sensor There is a small caved dot at the backside of the sensor which indicates the spot the magnet should be pointing at when passing the sensor Fasten the magnet to the spoke and tighten it loosely with a screwdriver Do not tighten it fully yet Fine tune the positioning of both the magnet and the speed sensor so that the magnet passes close to the sensor but does not touch it Move he sensor towards the wheel spokes as close as possible The gap between the sensor and the magnet should be under A mm 0 16 The gap is correct when you can fit a cable tie between he magnet and the sensor Rotate
4. Manufactured by Polar Electro Oy Professorintie 5 FIN 90440 KEMPELE Tel 358 8 5202 100 Fax 358 8 5202 300 www polar fi 2 mH yy FETT LISTEN TO YOUR BODY 17929839 00 GEN A Speed Sensor W I N D User manual Geschwindigkeitsmesser W I N D Gebrauchsanleitung Capteur de vitesse W I N D Manuel d Utilisation Snelheid Sensor W I N D Gebruiksaanwijzing Sensor de Velocidad W I N D Manual del Usuario Sensore di Velocit W I N D Manuale d uso Sensor de Velocidade W I N D Manual do utilizador Hastighedssensor W I N D Brugervejledning Hastighetssensor W I N D Brukerveiledning Hastighetssensorset W I N D Bruksanvisning Nopeussensori WLN D K ytt ohje gt E m POLAR LISTEN TO YOUR BODY ENGLISH The Polar Speed Sensor W I N D is designed to measure speed and distance when driving No other use is intended or implied Please follow the pictures on the front cover Product Elements 1 Polar Sulky Mount and Training Computer picture 1 A 2 Polar Speed Sensor rubber part and spoke magnet picture 1 B Installing the Polar Sulky Mount and Training Computer You can install the sulky mount and the sulky computer on the left or right sulky bar 1 Place the rubber part on sulky bar and insert the sulky mount on top of it picture 2 2 Pass the cable ties over the sulky mount and adjust them around the sulkybar Secure the sulky mount
5. ing computer is now ready to receive speed and distance data Select NO to cancel the teaching The teaching is cancelled and the training computer resumes contact with the previous sensor To return to Time mode press and hold the BACK button ENGLISH Care and Maintenance Keep the speed sensor clean Clean it with a mild soap and water solution and rinse off with clean water Dry it carefully with a soft towel Never use alcohol or any abrasive material such as steel wool or cleaning chemicals Do not immerse the speed sensor in water Avoid hard hits as these may damage the sensor Speed Sensor Battery Contact your authorized Polar Service Center for a replacement of speed sensor Polar recycles used sensors For more information on local after sales services consult the Polar Customer Service Card Frequently Asked Questions What should do if the speed reading is 0 0 or there is no speed reading while driving Start searching for the data again by pressing and holding the LIGHT button and selecting Seek sensor Make sure the position and distance of the sensor to the magnet are appropriate Check that you have activated the speed function in the training computer For further information see Speed Sensor Teaching ENGLISH If the 0 0 reading appears irregularly this may be due to temporary electromagnetic interference in your current surroundings If the 0 0 reading is constant you may have
6. roduct in other countries Polar Electro Inc Polar Electro Oy guarantees to the original consumer purchaser of this product that the product will be free from defects in material or workmanship for two years from the date of purchase Please keep the receipt which is your proof of purchase The guarantee does not cover the battery damage due to misuse abuse accidents or non compliance with the precautions improper maintenance commercial use and cracked or broken cases The guarantee does not cover any damage s losses costs or expenses direct indirect or incidental consequential or special arising out of or related to the product During the guarantee period the product will be either repaired or replaced at an authorized service center free of charge This guarantee does not affect the consumer s statutory rights under applicable national or state laws in force or the consumer s rights against the dealer arising from their sales purchase contract This product is compliant with Directive 93 42 EEC The relevant Declaration of Conformity is available at www support polar fi declaration_of_conformity ENGLISH This crossed out wheeled bin marking shows that Polar products are e are in the scope of Direc lectronic devices and ive 2002 96 EC of the European Parliament and of the Council on waste electrical and elec WEEE These products disposed of separately in encourages you to minim waste on
7. the environmen ronic equipment should thus be EU countries Polar ize possible effects of and human health also outside the European Union by following local waste disposal regu ations and where possible utilizing separate collection of electronic devices Copyright 2007 Polar Electro Oy FIN 90440 KEMPELE Finland Polar Electro Oy is a ISO 9001 2000 certified company All rights reserved No part of this manual may be used or reproduced in any form or by any means without prior written permission of Polar Electro Oy The names and logos marked with a symbol in this user manual or in the package of this product are trademarks of Polar Electro Oy The names and logos marked with a symbol in this user manual or in the package of this product are registered trademarks of Polar Electro Oy ENGLISH Disclaimer The material in this manual is for informational purposes only The products it describes are subject to change without prior notice due to the manufacturer s continuous development program Polar Electro Inc Polar Electro Oy makes no representations or warranties with respect to this manual or with respect to the products described herein Polar Electro Inc Polar Electro Oy shall not be liable for any damages losses costs or expenses direct indirect or incidental consequential or special arising out of or related to the use of this material or the products described herein
8. the front tire to test the speed sensor The flashing red light on the sensor indicates hat the magnet and the sensor are positioned correctly Once the magnet and the speed sensor are positioned correctly tighten the screw to the magnet with a screwdriver Also ighten the cable ties securely and cut off any excess cable tie ends Before you start driving set the wheel size of your sulky into the trainig computer ENGLISH Speed Sensor Teaching The training computer has to be coded to the Speed Sensor i e taught to receive speed and distance data This enables exercising in a group without interference from other sensors The training computer and sensor that come with the product set have already been synchronized but teaching is necessary when you start using a new sensor or if you use other bike settings than sulky 1 Install the speed sensor to your sulky as advised Before you start teaching make sure that there are no other speed sensors or training computers nearby 40 m 130 ft The procedure only takes a few seconds You can teach one sensor for each sulky Select Settings gt Sulky gt Sulky 17273 gt Speed Select On Off and On to turn the speed on Press OK Teach new sensor is displayed Select YES to confirm teaching Rotate the wheel a few times to activate the sensor The flashing red light indicates that the sensor is activated Completed is displayed once the teaching process is over The train
Download Pdf Manuals
Related Search