Easy Find Remote Control
Contents
1. Q MOTOROLA AT amp T U verse TV Easy Find Remote Control User Guide Congratulations on your purchase of the AT amp T U verse TV Easy Find Remote Control This remote is one of the most capable and easy to use remote controls available today It can control up to four devices It has many unique features for example the remote comes with a Base Station that recharges the remote so you never have to buy or install batteries Also the Base Station has a Find feature that lets you quickly find the remote in case you ve misplaced it With the touch of a single button on the Base Station the remote will sound and flash to make it easy to find your misplaced remote control More features for this unique remote are described in the remainder of this manual NOTE The remote control will only control the device that is selected by the appropriate mode key AT amp T TV DVD and AUX The mode key light for the selected device flashes each time a valid key is pressed Table of Contents Quick Setup Guide 224420420nnnennsnnnennnnnnennnennennnennennnennonnennnonnennnnnennnnnnnnnnnnnnnnnen 4 Advanced Feat res SetUp 4 u r un neuen mantel 9 Controlling Other Devices uruussesnsersennnnnnnnnennnnnnnnnennnnnnnnnnnnnnnnnnnnnnnnennnnnnnen san 9 Programming the Remote anne hie 9 VS ANI Gt Asoo ese ET ede cteesvSeceause coasnaegsasucsbdusscuseouns AT 12 Clearing Commands us444s404rnnnnnonnnnnnnnne2. 4 Press and release the DELETE key The mode key light turns off All learned Commands in the remote are now cleared E Volume Control Setup Options The volume controls will control your AT amp T U verse receiver until the TV device mode is programmed e g if DVD mode is selected then volume controls your AT amp T U verse receiver If TV mode is programmed and DVD mode is selected then volume controls your TV If you d like the volume commands to operate from just one device e g always TV then follow the instructions in Section E I If you d like the volume commands to be sent to different devices depending which mode you are in then follow the instructions in Section E Il S atst Advanced Features Setup E I Volume Always Controls the Same Device 1 Press the TV key and while holding it pressed press the OK key for 1 second 2 Release both keys all of the mode keys will flash followed by the TV mode key light remaining on 3 Press and hold the MUTE key for 3 seconds until the TV mode key light briefly turns off then remains on Press and release the mode key that you always want to operate the volume commands AT amp T TV DVD and AUX The selected mode key light will remain on 4 Press and release the MUTE key to save the setting The selected mode key light will turn off indicating a successful setup The volume commands will be setup for the selected device despite what mode is selected If the selected mode key light
3. and while holding it pressed press the OK key for 1 second Then release both keys You are now in setup mode 2 Press and release the mode key TV DVD or AUX you want to disable 3 Press and release the 0 key The selected mode is now disabled If no mode key is pressed in step 2 ALL modes TV DVD and AUX will be disabled Note you can turn individual devices on off by pressing the desired Mode key followed by the Power key It is important to point your AT amp T remote directly towards the devices for this feature to operate correctly E atat Advanced Features Setup J Backlight Cancellation Feature Your AT amp T U verse TV Easy Find Remote Control has the ability to toggle between turning the backlights on or off If you wish to use this feature follow these instructions 1 Press and hold the TV key and while holding it pressed press the OK key for one second and release both keys at the same time 2 All the mode keys flash and the TV mode key light stays on 3 Press the GUIDE key all backlights will no longer turn on To reverse this process so that the backlights turn on when the remote control is being used simply follow the same steps of the above section one more time K Resetting the Remote Control to the Factory Default Settings 1 Press and hold the TV key and while holding it pressed press the OK key for one second and release both keys at the same time 2 All the mode keys will flash the TV mode key lig
4. your AT amp T U verse TV Easy Find Remote Control for your other devices you will need to setup the TV DVD and AUX mode keys to control the devices Section A Please refer to the code list for a list of supported brands and models If you do not find the brand of your device on the supported code list please refer to section B for the search function or you may use section C for instructions on the learning feature of your remote control S atst Advanced Features Setup Programming the remote to control other devices cont If you have an integrated or combination unit such as a TV DVD each component of the unit may need to be setup separately by setting up both the TV and DVD mode keys NOTE The DVD and AUX mode keys can be setup with any code The TV mode key can only be setup with TV codes A Manual Programming Use the following steps to setup the TV DVD or AUX mode keys 1 Power on the device you want to program and locate the 4 digit code from the code list 2 Press and hold the mode key TV DVD or AUX and while holding it pressed press the OK key for one second 3 Release both keys all of the mode keys will flash then the selected mode key light will stay lit 4 Enter the 4 digit code by pressing the numerical keys 0 9 The selected mode key light will blink for each digit entry and will remain off after the entry of the fourth digit indicating a successful setup Advanced Features Setup 5 Point the
5. D 2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION This equipment generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturers instructions it may cause interference to radio and television reception It has been type tested and found to comply with the limits for remote control devices in Fold out code list goes here accordance with the specifications in Sub Parts B and C of Part 15 of FCC Rules which are designed to A provide reasonable protection against such interference in a residential installation However there is no 2 pages wide and 2 pages deep guarantee that interference will not occur in a particular installation If this equipment does cause interfer printed on both sides ence to radio or television reception which can be determined by unplugging the equipment try to correct the interference by one or more of the following measures e Reorient the antenna of the radio TV experiencing the interference e Relocate the equipment with respect to the radio TV e Move the equipment away from the radio TV Plug the equipment into an outlet on a different electrical circuit from the radio TV experiencing the interference e If necessary consult your local dealer for additional suggestions The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifica
6. ds and turns off then you will need to start over from step 1 atat Advanced Features Setup G Mode Deactivation If you d like to deactivate a device mode then follow the instructions below 1 Press and hold the mode key to be deactivated TV DVD or AUX and while holding it pressed press the OK key for one second 2 Release both keys all of the mode keys will flash and then the selected mode key light will remain on 3 Enter the 4 digit code 1753 by pressing the numerical keys 0 9 The selected mode key light will blink for each digit entry and will remain off after the entry of the fourth digit indicating the mode is deactivated Note the AT amp T mode cannot be deactivated Advanced Features Setup H Multiple Device Power Control Setup Options After pressing the AT amp T key pressing the Power key turns the U verse receiver on or off AND turns on or off the TV if it has been setup If you want the Power key to turn on other devices at the same time you can enable these as follows 1 Press and hold the AT amp T key and while holding it pressed press the OK key for 1 second Then release both keys You are now in setup mode 2 Press and release the mode key TV DVD or AUX you want to enable 3 Press and release the 1 key The selected mode is now enabled If no mode key is pressed instep 2 ALL modes TV DVD and AUX will be enabled To remove a mode from the Power key 1 Press and hold the AT amp T key
7. emote Control Model A10 will properly perform its intended functions This is a Limited Warranty that does not cover defects resulting from misuse abuse accident or negligence including any failure to follow the instructions provided with the remote control Consequential and incidental damages are also not recoverable under this limited warranty but some states do not allow the exclusion or limitation of incidental or consequential damages so this limitation may not apply to you If during the first year after the purchase date and under normal working conditions the remote control does not perform its intended functions please call 1 800 861 2974 Monday through Saturday between the hours of 10 00 A M and 8 00 P M Eastern Standard Time to replace your remote control If the remote control is replaced by AT amp T during the first year the replacement remote is warranted to properly perform it s intended functions for either ninety 90 days or the remainder of the remote control s one year warranty from the original date of purchase whichever is longer To receive a replacement remote control you must provide proof of purchase E at amp t S atat
8. emote and while holding it pressed press the OK key for one second and release both keys at the same time Next press the MENU key to enter the ID learn mode both the AT amp T and AUX lights remain on 2 Press the Find key on the Base Station the remote will accept the new ID and the lights will flash once and then turn off 3 To exit this mode without changing the code simply press any key on the remote control Advanced Features Setup M Troubleshooting Learning You can only learn one device type under any one mode key For example only learn TV codes under the TV mode DVD codes under the DVD mode etc If you are trying to learn from a Universal remote it might have more than one code type stored under a mode a No functions may be stored under the LEARN key or in the AT amp T mode b Depending on the remote you are trying to learn some keys may not be learnable c Only one original device type can be learned per individual mode d Use fresh batteries for your original remote and make sure the batteries in your AT amp T U verse TV Easy Find Remote Control are fully charged e Keep at least three feet away from incandescent or low energy lights when learning f Before learning clear all learned commands refer to Section D II then try learning 2 or 3 commands initially g Point your original remote at the bottom end of your AT amp T U verse Remote Control so the IR elements on both remotes are directly in line with each o
9. flashes for 3 seconds and turns off then the selected mode will have no volume commands of its own and will need to start over from step 1 above and select a different mode to program the device Advanced Features Setup E Il Volume Control Depends on Device Selected 1 Press and hold the TV key and while holding it pressed press the OK key for one second 2 Release both keys all of the mode keys will flash followed by the TV mode key light remaining on 3 Press and hold the MUTE key for 3 seconds until the TV mode key light briefly turns off then stays on then release the MUTE key 4 Press and release the MUTE key to save the setting The TV mode key light turns off indicating successful setup The volume commands will now work for different devices NOTE If a programmed mode key has no volume commands of its own then the volume control will normally operate the TV If an invalid key is pressed the selected mode key light flashes for 3 seconds and turns off The remote control returns to normal operation and you will need to start over If no key is pressed within 30 seconds the remote control times out the selected mode key light flashes for 3 seconds and turns off The remote control returns to normal operation at which time you can start over gt atat Advanced Features Setup F Channel Control Setup Options The channel controls Channel Up Down 0 9 and LAST will always work your AT amp T U verse receiver If
10. g If the code for your device is not found in the code list and the search feature was not able to find the code for your device then the learning feature may be your best option The learning feature lets you learn functions from your original remote control Note Learning cannot be performed for any mode until after that mode is setup with a valid code So to learn the keys first setup the mode with a valid code see page 10 select any code for the appropriate mode from the code list on page 29 and 30 then follow the steps on the following page Advanced Features Setup C l Learning Commands 1 Press and hold the mode key TV DVD or AUX on the U verse AT amp T remote and while holding it pressed press the LEARN key for remote one second then release both keys 2 All of the mode keys will flash and then the selected mode key light remains on 3 On your U verse remote press and release the key that you want to teach 1 inch 4 While pointing your original remote at the bottom of your AT amp T apart U verse TV Easy Find Remote Control approximately 1 inch apart press and hold the original remote key until the mode key light blinks once and stays on If there is a learning problem the mode key light blinks for three seconds and stays Your on If this happens repeat steps 3 and 4 above ongina 5 Repeat steps 3 and 4 above for each key you want your AT amp T U verse TV Easy Find Remote Control to learn Press and relea
11. hat the charging points are in full contact by seeing that the charging lights on the Base Station are lit NOTE It is not necessary to charge the remote control often but remember to place it in the Base Station for at least two overnight sessions per month if possible Quick charge the remote in 30 minutes or fully charge the remote in 12 hours atat vere Write your codes here so you don t forget them 4 TV DVD AUX I atat Charging lights Quick Setup Guide 5 How to use the Find Feature STEP 1 If you have misplaced the remote control simply press the AT amp T globe labeled FIND on the Base Station The remote will sound and flash to make it easy to find your misplaced remote control STEP 2 Once you have located the remote control press any key on the remote to stop the sound and flashing keys AT amp T globe Find key Advanced Features Setup Controlling Other Devices In order to control other devices with your AT amp T U verse TV Easy Find Remote Control you need to tell the remote control what types of devices you have Sections A and B take you through the steps needed to do this The volume controls will control your AT amp T U verse receiver until the TV device mode is programmed The channel controls will always control your AT amp T U verse receiver If you want to change this you should follow the steps in Sections E amp F Programming the remote to control other devices To use
12. ht will stay on Advanced Features Setup 3 Press and hold the DELETE key for 3 seconds until the TV mode key blinks and stays off The remote control is now reset to factory default settings If you want to use the remote control for your TV and other devices you will need to setup the TV DVD and AUX mode keys 4 lf no key is pressed within 30 seconds the remote control times out The selected mode key light flashes for 3 seconds and turns off The remote control returns to normal operation and you will need to start over L Finding More Than One Remote If you own more than one AT amp T U verse TV Easy Find Remote Control and Base Station you can set each Base Station to find only its own remote with 16 unique codes With the first power up of the Base Station it will be set to find ALL remotes To set the Base Station so that it finds a specific remote when there are multiple remote in the household follow the instructions on the following page E at amp t Advanced Features Setup L Finding More Than One Remote cont 1 Press and hold both clock setting keys H and M at the same time for 3 seconds The display shows the current ID from 1 to 16 or ALL 2 Press the M key to cycle from 1 to 16 including a selection for all remotes in the household 3 Then press the H key to confirm the selection To set the remote to the same ID as the Base Station follow these instructions 1 Press and hold the TV key on the r
13. nd the M buttons on the bottom of the Base Station to set the hours and minutes of the clock STEP 2 With the remote control in the Base Station press and hold the FIND button which will cause the clock to dim as desired Press and hold the FIND button again to make clock brighter as desired Quick Setup Guide Quick Setup Guide 3 How to charge the remote control 4 How to manually setup the remote STEP 1 Power on the device you want to setup STEP 2 Locate the 4 digit code from the code list see pages 29 and 30 STEP 3 Press and hold the mode key TV DVD or AUX and while holding the mode key press the OK key STEP 4 Release both the mode key and the OK key All the mode keys flash but the selected mode key stays on STEP 5 Enter the 4 digit code from the code list The selected mode key light blinks for each digit entry and remains off after the entry of the fourth digit STEP 6 Point the remote control at the selected device and press the power key once The device should turn off if you have found the correct 4 digit code STEP 7 If there are multiple codes and one does not work repeat steps 2 6 using the next code until you find the correct one If it still does not work as intended please refer to the advanced section starting on page 9 STEP 1 Place the remote control in the Base Station A magnet inside the Base Station pulls the remote into place to make contact with the charging pins STEP 2 Make sure t
14. nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnennnnnnnnnnnnnnnnnnn 14 Volume Control Setup Options nee 15 Channel Control Setup Options ur ursensnnennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnennnnnnnnnnnnnnnnnnnn 18 Mode DE ACU VATION UAREPEREPERRERITEEPFUIFFELPERSEIEERPENELLEPEREENEPEREEECHETESEIEERELELTEFPERLEERRSREERCREEEHTETERERFE 20 Multiple Device Power Control Setup Options rsssersennnnnensnnennnnnnnnnnnnnnnnnennnnnnn 21 Backlight Gancellation u un een iaa 22 Resetting the Remote Control urs2u0s400nnnnnnennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn manner naar 22 Finding More Than One Remote uussneeesnnnnsnnnnensnnnnnnnnnnn ernennen ernennen ern nr 23 Troubleshooting Learning 4 ae ea aaa naar ran neun ran ade 25 Quick Setup Guide 1 How to connect the Base Station STEP 1 Determine where you would like to place rT the Base Station STEP 2A Powering from your U verse receiver within 3 feet Connect the square end of the supplied USB cable to the Base Station and the rectangle end to the back of the U verse receiver STEP 2B Powering from a Wall Outlet further than 3 feet from U verse receiver Connect one end of the supplied plug in power supply to the Base Station and the other end to a near by wall socket Note you only need to follow STEP 2A or STEP 2B not both BEE STEP 2B STEP 2A Quick Setup Guide 2 How to set the clock STEP 1 Use the H a
15. remote control at the selected device and press the power key once The device should turn off If the device stayed on repeat the steps 2 thru 5 trying each code for your brand until you find the correct code Repeat above steps to setup another device To use the remote control for your U verse receiver press the AT amp T mode key NOTE If an invalid code is entered or no key is pressed at all for 30 seconds the mode key light flashes for 3 seconds and turns off The remote control returns to normal operation and you will need to start over from step A2 to setup the device B Using the Search Function To search for a particular device code for DVD or AUX e g VCR use the Manual Programming for section A and program DVD or AUX with any VCR code prior to starting a search 1 Turn on the device you want to control and point the remote at that device 2 Press and hold the mode key TV DVD or AUX and while holding it pressed press the OK key for one second S atst Advanced Features Setup B Using the Search Function cont 3 Release both keys all of the mode keys will flash then the selected mode key light will stay lit 4 Press the power button repetitively until the selected device turns off Once your device has turned off press OK to save the code 5 To indicate a successful setup the selected mode key will turn off and you are ready to setup another device by following steps 1 thru 4 of this section C Learnin
16. se the LEARN key when all desired remote commands have been learned If you have encountered difficulties with the LEARN key setup please refer to Section M Troubleshooting Learning atat Advanced Features Setup C l Learning Commands cont NOTE It is not necessary to have your AT amp T U verse TV Easy Find Remote Control learn every key from your original remote since most of the keys will not be used under normal daily use The best practice is to teach only the keys that help you navigate for the best experience like your volume up and down channel up and down and DVR functions D Clearing Commands D I To Clear all Learned Commands under a single mode 1 Press and hold the mode key TV DVD or AUX and while holding it pressed press the LEARN key for one second then release both keys 2 All the mode keys will flash and the selected mode key light will stay on 3 Press and release the LEARN key once The mode key light blinks off 4 Press and release the DELETE key The mode key light turns off All learned Commands under that mode are now cleared Advanced Features Setup D II To Clear all Learned Commands under ALL modes 1 Press and hold the mode key TV DVD or AUX and while holding it pressed press the LEARN key for one second then release both keys 2 All the mode keys will flash and the selected mode key light will stay on 3 Press and release the LEARN key twice The mode key light blinks off
17. ther see diagram on page 13 You may need to adjust the height of either remote to achieve this S atst Advanced Features Setup M Troubleshooting Learning cont h Avoid learning your original remote s Volume Mute keys unless you are sure these operate the same device i Avoid learning your original remote s VCR or DVD transport keys unless you re sure these operate the same device j If learning the first or second keys for a mode results in continuous errors then try the following i End the learn session by pressing the LEARN key Fold out code list goes here ii Clear out the learned commands for that mode iii Check the IR elements are correctly aligned between the two remotes 2 pages wide and 2 pages deep iv Adjust the distance between the two remotes to be closer e g half an inch or printed on both sides further away e g 2 inches from each other v Try learning the original remote for that mode again If problems reoccur with the same key check the original remote key being learned does it transmit Does it operate the target device Try learning that key under a different clear mode If it learns OK then it is likely to be a different code type from the others and cannot be learned under the same mode E atat i a FCC Statement THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AN
18. tions to this equipment Such modifications could void the user s authority to operate the equipment E at amp t Caring for the environment by recycling This symbol on a product means the product should not be disposed of with household waste Disposal of your Base Station Power Supply or Remote Control Please do not dispose of any of the items in this package with your household waste These items should be disposed of accordance with the national collection and recy cling schemes operated by your local or regional authority NOTE placing the Base Station near a CRT old style TV can affect the color since the Base Station includes a magnet If you have a Pacemaker do not place the Base Station near it The AT amp T U verse TV Easy Find Remote Control is intended and sold for use only with AT amp T s U verse TV receivers May not be compatible with all entertainment systems or capable of accepting every programming code for other devices Limited one year replacement only warranty For additional information For help with your AT amp T U verse service or this remote control please visit http uverse att com support or call AT amp T Customer Care at 1 800 ATT 2020 When prompted say you need U verse Technical Support For a Spanish version of this user manual visit www helpme att net controlremoto One 1 Year Warranty AT amp T guarantees from one 1 year of purchase this AT amp T U verse TV Easy Find R
19. you d like the channel commands to be sent to different devices depending which mode you are in then follow the instructions in Section F I F I Channel Control Depends on Device Selected 1 Press and hold the TV key and while holding it pressed press the OK key for one second 2 Release both keys all of the mode keys flash followed by the TV mode key light remaining on 3 Press and hold the LAST key for 3 seconds until the TV mode key light briefly turns off then stays on then release the LAST key 4 Press and release the LAST key to save the setting The TV mode key light turns off indicating successful setup The channel commands will now work for different devices Advanced Features Setup F Il Channel Always Controls your AT amp T U verse receiver Factory Default 1 Press and hold the TV key and while holding it pressed press the OK key for 1 second 2 Release both keys all of the mode keys will flash followed by the TV mode key light remaining on 3 Press and hold the LAST key for 3 seconds until the TV mode key light briefly turns off then remains on 4 Press and release the AT amp T mode key The selected mode key light remains on 5 Press and release the LAST key to save the setting The AT amp T mode key light will turn off indicating a successful initial setup The channel commands will be setup for your AT amp T U verse receiver regardless of what mode is selected If the selected mode key light flashes for 3 secon
Download Pdf Manuals
Related Search