LED LEONARDO 120 W INSTRUCTION MANUAL
Contents
1. This Function is to LOCALLY DIM the LED INTENSITY from 0 to 100 Product is delivered with default setting of the DIMMER at 0 The intensity goes in increments of 1 100 so the display will show 000 with the dimmer at 0 and FULL with the dimmer at 100 Temporary push will increment the value by 1 100 if the button is kept pushed the increment on numbers is getting fast Once the desired Lighting Level is accomplished and it is wanted to leave that level and go to other functions of the MENU press ENTER LOCAL OR REMOTE CONTROL SETTINGS The LED Fresnel has the facility to block the LOCAL DIMMING SETTING and maintain it when the POWER is turned first OFF and than ON again This allows for the LIGHT to be TUNED and FOCUSED locally and its dimming level can be blocked so that for instance a system lighting a SET can be operated by a remote switch or simple brakers by TURNING POWER ON The relevant menu to access this function is CTRL to enter in this menu press X ENTER it is than possible to select either DMX or AUTO by acting on the A or Y button and than press X ENTER again The machine is set to DMX as default e In DMX mode the Fixture accepts DMX control if in this mode the local DIMMING CONTROL is SET to a level the Light behaviour will follow the HTP Highest Takes Precedence modality in other words it will keep the local DIMMING setting until the DMX level of the specific channel will be higher fr2. ILT Italy S r l B Via Cancelliera n 10 a 00041 Albano Laziale Rome Italy tel 39 06 902901 fax 39 06 90231051 www desisti it LED LEONARDO 120 W LED Fresnel SPOTLIGHT white light either Tungsten or Daylight balanced Correlated Color Temperature INSTRUCTION MANUAL E LT320 110 Tungsten CCT LT321 110 Tungsten CCT LD320 110 Daylight CCT LD321 110 Daylight CCT Manual Operated Pole Operated MANUFACTURER REPRESENTATIVE ILT Italy S r l Via Cancelliera 10a 00041 Albano Laziale Rome Italy Tel 39 06 902901 Fax 39 06 90231051 U R L www desisti it E mail desisti desisti it 1 INTRODUCTION Congratulations on your purchase of a LED LEONARDO 120W lighting fixture Our commitment to Total Customer Satisfaction and our consolidated experience and leadership in design innovation and manufacturing of lighting products for the professional Entertainment Industry means you can depend upon the quality of this product The LED LEONARDO 120W is a compact highly efficient Fresnel lens spotlight using a LED ARRAY combined with the DE SISTI Patented optical system to optimize the photometric performances of LED ARRAYS when utilized in combination with either Fresnels or Plano Convex lenses The Lighting Fixture is DMX Controlled and includes a number of parameters that can be set locally it is equipped with a universal voltage power supply for AC feed and it is available with either Tungsten or Dayligh
3. in the Local Menu chapter and Use tt 6 LOCAL MENU PGM PORT For Firmware Upgrade A FUNCTION 1 Scrolling UP Increases value function key ENTER Select Confirm y FUNCTION 2 Scrolling DOWN Decreases value function key Display When the push button are not used for more than 15 seconds the display will go OFF It will go ON again anytime a push button is activated DMX Presence Shows the presence of DMX LED lit DMX present DEFAULT SETTINGS ARE INDICATED IN BOLD LETTERS ON THE FOLLOWING TABLE The following are the BASIC FUNCTIONS and COMMANDS that are provided on the LOCAL MENU of the LED FRESNEL The unit is provided with a USER MENU accessible instantly on the product The unit has also a SERVICE MENU that is only accessible through a PASSWORD and is reserved for QUALIFIED and TRAINED PERSONNEL 1st MENU 2nd MENU Explanation of Each MENU FUNCTION Displayed Displayed scrolling with the A and the W buttons after pressing the X that stands for ENTER DMX ADDRESS This Function is to SET the DMX address from 1 to 512 Product is delivered with default settingof the DMX address at 1 Once the C001 is displayed act on the A button to increase the address to the desired value Temporary push will increment the value by 1 if the button is kept pushed the increment on numbers is getting fast Once the desired Address number is accomplished press X ENTER to make it active LOCAL DIMMING CONTROL
4. temperature conditions the LED ARRAY shall never reach the 80 C limit The above protection threshold is there to protect the LED ARRAY from stressed working conditions in case some other failures or specially critical working conditions are causing an over temperature CHANNEL SETTING RESOLUTION amp FUNCTION This Function is to set the DIMMING RESOLUTION either at 8 bits or at 16 bits Once CHAN is displayed act on the A or v buttons to scroll through the following choises 8D 8 bits resolution the display will show 8D and this is the default setting The Fixture utilises 1 DMX Circuit for the Light Dimming which is the BASE CIRCUIT set in the ADDRESS e 8DS NOT ACTIVE for future use The foreseen function for this setting is 8 bits resolution and STROBE the display will show 8DS The Fixture will utilise 2 DMX Circuits the BASE CIRCUIT set in the ADDRESS will be the LIGHT DIMMING and the second circuit BASE 1 will be the STROBE e 16D 16 bits resolution the display will show 16D The Fixture utilises 2 DMX Circuits the BASE CIRCUIT set in the ADDRESS is the Coarse Dimming the second Circuit BASE 1 is the Fine Dimming 16DS NOT ACTIVE for future use The foreseen function for this setting is 16 bits resolution and STROBE the display will show 16DS The Fixture will utilise 3 DMX Circuits the BASE CIRCUIT set in the ADDRESS will be the Coarse Dimming the second Circuit BASE 1 will be the F
5. dition It consists of a fresnel lens made by borosilicate untoughened glass with a Diamater 250 mm thickness 7 mm typ 4 min A WARNINGS e Do not operate the product if the ambient temperature exceeds 40 C e Provide a minimum clearance of 0 1m 4 in around fans and air vents This Manual is applicable to the following products a at a Revised March 29th 2012 LT 320 starting from S N Pag 3 LD 320 starting from S N e SHIELDS LENSES SAFETY OR DICHROIC GLASSES SHALL BE CHANGED IF THEY HAVE BECOME VISIBLY DAMAGED TO SUCH AN EXTENT THAT THEIR EFFECTIVENESS IS IMPAIRED FOR EXAMPLE BY CRACKS OR DEEP SCRATCHES e THE LUMINAIRE SHALL ONLY BE USED COMPLETE WITH ITS PROTECTIVE SHIELD D Applying power Never connect to dimmer power Install a power plug on the power cable using the following pin assigment 1 Neutral 2 Live Green Yellow Ground This fixture must be connected to ground Make sure the local power voltage is within the range specified If so connect the power cable and turn the power on E Stand Alone operation Using the navigation buttons and display readout refer to the Local Menu chapter navigate to Manual and set the desired intensity for additional operations see Local Menu chapter F DMX operation Connect a DMX cable Navigate to Address mode Addr and set the desired address refer to the Local Menu chapter Connect to DMX controller refer to the Channel Setting
6. ine Dimming the third CIRCUIT BASE 2 will be the STROBE Of course the 16 bits function is useful if the corresponding circuits on the DMX LIGHTING BOARD are also set at 16 bits WARNING if the LED FRESNEL is set at 16 bits but more units are having a consecutive unitary address for instance first fixture set at Address 1 second fixture set at Address 2 and so forth the DMX Channel controlling the Coarse Dimming of the second unit will also control the fine dimming of the first unit In this case it is recommended that all fixtures are set to 8 bits DMX LEVEL It Shows the DMX Input level on percentage 0 99 and FULL received effectively from the Fixture Press ENTER to exit this MENU 7 CHARACTERISTICS AND PERFORMANCE DATA DESCRIPTION VALUE DESCRIPTION VALUE P22 Power supply 100 240 V nominal 50 60 Hz gt Max Housing temperature gt This product uses a 5 pin XLR for DMX input and output gt Weight of Fixture s5 DMX Data link Use a shielded data cables 13 5 14 8 USITT DMX512 A gt Donot overload the daisy chain can be used on a single DMX gt Weight of barndoor chain 1 4 kg 1 65 kg PODET Weight of color frame 0 6 kg gt DMX 2 at 8bit Dimmer w strobe gt Size of scrims amp color Seat Diameter Channels 2 at 16bit Dimmer frame 3 at 16bit Dimmer w strobe Seat Diameter Ring Diameter gt Size of Barndoor ring 313 mm 12 s5 Pr ion Class 1 ground connection re
7. ing from S N _ ag 6 LD 320 starting from S N
8. olored in red Working conditions gt Working Position Lighting fixture Max Tilting 90 from horizontal gt Ambient Temperature ta Minimum 5 C maximum 40 C at the place of installation and Storage gt Humidity 25 80 not condensing at the place of installation and Storage The luminaire should never be OPERATED close to inflammable materials The ones indicated in the above table are the minimum distances recommended Other requirements for safe use are Do not cover the apertures of the luminaire housing They are essential for correct ventilation Use only original accessories and spares from De Sisti Lighting Before hanging the luminaire ensure that the suspension point or the stand is properly rated to accept the luminaire weight In case of pole operated use fit only a P O stirrup from De Sisti Lighting A suitable secondary safety suspension device safety cable chain or equivalent must be fitted between the suspension point and the eyelet at the front of the body mo OUD WARNING DO NOT MOUNT THE LUMINAIRE ON A NORMALLY FLAMMABLE SURFACE 5 INSTALLATION INSTRUCTIONS The following procedure should be adopted Before connecting the luminaire to the electrical mains ensure that A Earth line is present on the power socket B The mains voltage is within the rated range of the luminaire see technical data on the rating label C The front safety shield is present and in good con
9. om that level onwards the DMX level will take precedence In this condition if the DMX connection is removed the light will keep the last level until power is ON It will reset and Start at Oafter Power OFF and ON again In AUTO mode the light will ignore any DMX control In this mode any local dimming setting will be maintained and will be automatically recalled after power off when turning the power on again This Manual is applicable to the following products Revised March 29th 2012 LT 320 starting from S N LD 320 starting from S N 1dstMENU 2ndMENU Explanation of Each MENU FUNCTION 2 i aests lt lt COtit s Displayed Displayed i _ scrolling with the A and the Y buttons i ___ after pressing the X that stands for ENTER TEMPERATURE This function Displays in real time the LED ARRAY Case temperature in C When pressing Enter again you exit from the temperature display The steady state TEMPERATURE of the ARRAY reaches approx 55 C after many hours of continuous operation with an ambient temperature of 25 30 C The Thermal Handling of the LED is Automatically handled by the local electronics and the LED will operate until the ARRAY temperature reaches 80 C that anyway is still way within the prescribed maximum nominal prescribed by the ARRAY manufacturer that is 105 C In case the ARRAY temperature reaches 80 C the unit will automatically turn off Even in extreme Ambient
10. quired Specifications subject to change without notice This Manual is applicable to the following products p Revised March 29th 2012 LT 320 starting from S N ag 9 LD 320 starting from S N 8 DIMENSIONS Dimensions in mm l Dimensions in mm 9 PERIODIC INSPECTION amp MAINTENANCE This product requires very little routine maintenance if any but has special cleaning instructions Disconnect fixture from power and allow it to cool for 10 min 1 Vacuum or gently blow away any dust from fan blades and grills 2 Very gently clean the LED with Isopropyl alcohol 3 Clean the lenses with a soft damp cloth 4 Check the condition of the safety shield see chapter Installation Instructions before every use 5 Check Power supply cable and DMX control cable proper conditions 10 SAFETY STANDARDS Europe The product conforms the Applicable European Directives amp Standards Low Voltage Directive 73 23 EEC as amended by 93 68 EEC gt EMC Directive 89 336 EEC as amended by 92 31 EEC amp by 93 68 EEC Europen Standards EN 60598 2 17 EN 60598 1 EN 55015 EN 61547 Disposing of this product Help preserve the environment Ensure that this product is recycled at the end of its life This product is in compliance with the RoHS and WEEE directives This Manual is applicable to the following products p Revised March 29th 2012 LT 320 start
11. t Balanced CCT lt utilizes Standard accessories from the DE SISTI range of equivalent Fresnel Lens size such as Barndoor Colour Frame Cones scrims This Manual is applicable to the following products p Revised March 29th 2012 LT 320 starting from S N ag 1 LD 320 starting from S N 2 YOKE AND ACCESSORIES ASSEMBLY 1 0 STIRRUP ASSEMBL M10x25 F D II NVZZ O A L PACER B E HOLDING STR A O ODO OANMAUAWN VOTED BRACKET POT FLOOD T ATCH JIN SPIGOT S SPIGOT M12 OVU aA WN 1 BARNDOOR 2 COLOUR FRAME 3 BOLT M10x30 4 ER 010 5 R 6 ST ASSEMBLY 10 S 12 BOLT M10x80 13 CATC 14 YELLOW CUP ASSEMBLY POLE OPERATED 3 POWER AND DMX DAISY CHAIN The LED LEONARDO 120W permits both POWER and DMX DAISY CHAIN In fact each Fixture is respectively equipped with For DMX _ ay e 1 XLR5 pin Panel Mo
12. unt Male DMX IN ra Deets AS e 1 XLR5 pin Panel Mount Female DMX OUT For Mains Supply e 120A Powercon NAC3MPA BLUE POWER IN e 120A Powercon NAC3MPB WHITE POWER OUT It is recommended to Daisy Chain a Max of 12 fixtures even if the limitations imposed by DMX Standards are for an higher q ty of units and even if the Powercon Connections are rated for 20A max This Manual is applicable to the following products p Revised March 29th 2012 LT 320 starting from S N ag 2 LD 320 starting from S N 4 SAFETY INSTRUCTIONS Professional use This luminaire has been designed for professional use and must be operated by qualified personnel only Not for residential use gt Grounding WARNING THIS LUMINAIRE MUST BE GROUNDED gt Electrical connections IMPORTANT The cores in this mains lead are colored in accordance with the Europe Amer ca si Green amp yellow Green or green amp yellow White S following code White In case the colors of the cores do not correspond to the colors of the connection points on your plug please proceed as follows e the green or green and yellow core must be connected to the connection point marked with the letter E or with the symbol or colored in green or in green yellow e the blue or white core must be connected to the connection point marked with the letter N or colored in black e the brown or black core must be connected to the connection point marked with the letter L or c
Download Pdf Manuals
Related Search