USER MANUAL Read or download.
Contents
1. ROBOTIC VACUUM CLEANER MODEL NO HOVO620 USER MANUAL 224 Table of Contents Safety Instrucions Product Features Product Illustrations Main unit and acceccories Main Unit and Dust Bin Charging Station and Virtual Blocker Remote Control Unit Unit Display Panel Product Operations Battery Charging Methods Cleaner Operations Schedule Cleaning Time Cleaner Operations Virtual Blocker Usage Product Maintenance Clean Side Brushes Clean Dust Bin and Filters Clean Sensors Assembly 8 Disassembly The Mop Troubleshooting Error Codes Chart Replaceable Modules Battery Installation and Replacement Unit Usage Limitation Product Specification 12 13 12 12 13 13 14 16 14 15 16 16 17 Safety Instructions Before using this product please read the following safety instructions and follow all normal safety precautions Read this user manual thoroughly and carefully before using this product M Save this user manual Follow these precautions to reduce the risk of injury or damage WARNING Only a certified technician can disassemble and or repair the product Only use the adapter provided by the factory Using other non authorized adapter may cause electric shock fire or product damage Do not touch the power cord plug or adapter when your hands are wet Do not make clothes or part of a body drawn into the product swheels Do not use product near any flammables B Do not c2. unit status battery charging status and error codes 2 display Shows an error has occurred EJ T display Flashes constantly when dust bin is full or when vacuum intake is blocked Control Button g os Clean Press ae to complete following operations A To change from sleeping mode to selected mode pressing this button to change from selected mode to sleeping mode B To confirm scheduling in scheduling mode C To start cleaning in selected mode E C Scheduling A Press ra to enter scheduling mode B Press this button to switch between hour and minute in scheduling mode C Keep pressing this button for 5 seconds to cancel scheduling in scheduling mode fi gt Spot Press ES to complete following operations A Press this button to increase number in scheduling mode B When cleaner is in selected mode press this button to make cleaner start spot cleaning YA Home Press sej to complete following operations A Press this button to decrease number in scheduling mode B When cleaner is in selected mode pressing som to return the cleaner to self charging base Product Operations Battery Charging Methods Place self charging base Note Put self charging base against the wall and remove obstacles about 3 ft at two sides and about 6 ft in front Turn on the Power Switch at the side of cleaner then display will flash If the unit does not receive a command for 20 se
3. When the cleaner detects an obstacle it will use its side brushes to clean the sides Note Place cleaner against a wall Press EDGE on remote unit to start edge cleaning mode press CLEAN to stop Virtual Blocker Virtual Blocker creates an invisible barrier that the cleaner will not cross The Virtual Blocker can be used to confine the cleaner in a room put it outside the door way or prevent it from going towards fragile objects Virtual Blocker can block an opening of up to 4m 13 ft After batteries are installed turn on the power switch Put the virtual blocker where you want it to work Note When using virtual blocker put ep side of virtual blocker towards 4M the area you want to set ia Turn the power off when not using virtual blocker 11 Product Maintenance Clean Side Brushes A Check side brushes for damage or foreign object on the brush B Clean the side brushes C 6 Remove the screws of the side brushes g Pe Replace brushes with new ones O Use screws to lock the new brushes in place Note Make sure the L and R on the brush matches with the L and R on the cleaner Clean dust bin and filter Note After taking out dust bin check if there is foreign object stuck or block the vaaum pao ra clean it if necessary A Press PUSH to open the dust bin cover B Take out the dust bin C Separate HEPA filter from dust bin D Pull
4. battery using the 2 strip holder on its sides D Disconnect the wire connector that connects the battery and unit E Puta new battery into battery slot with 2 strip holders face up F Reconnect the wire between the battery and unit correctly G Make sure the wire connector is stored on the cavity H Put the battery cover back and make sure side brush is not stuck in I Lock back battery cover with screws Note Only use factory authorized batteries Unit Usage Limitation The cleaner unit can ONLY be used at residential houses indoor and dry floor It will clean the debris dirt dust and pet hairs off the floor and work well on hardwood tile linoleum and low pile up to 0 5 inches carpet 16 Product Specifications Classification Item Detail Mechanical PEN r Specifications 9 54 90mm Power voltage 144 V Battery UE NEM Specifications P Battery specifications 2000mAH Specification op 24 0V11 0A Dust bin Dustbin capacity 0 4Liters Changing type Auto Charging Manual Charging Cleaning 7204 Cleaning mode Auto Spot Edge Daily Schedule Specifications Cleaning time About90min Main Unit Button Type Touch LED display 17 Metapolnc http www infinuvo com http www metapo com
5. check if the wheel can tum freely Remove hair and debris from the cleaners right Right wheel error wheel Push it in and out and check if the wheel can tum freely ES NE Unit is lifted up Place cleaner on the floor NES Cliff sensor fail Clean the cliff sensor with a cotton swabs Check bumper can move freely and is free Bumper sensor fail from any debris Left brush error Remove and clean left brush MESS Right brush error Remove and clean right brush NES Unit is stuck Move main body and start again ty and flash Dust bin full Clean dust bin and vacuum intake Note If the error condition is not resolved do the following 1 Restart the cleaner by switching off and on power switch 2 If restarting doesn t work remove battery for more than 10 minutes to reset system 3 If it is still not working then contact your local service center for repair 14 Troubleshooting Replaceable modules There are a number of modules that can be replaced Battery Cover Battery MAS smeji lt Z lt lt Right Side Brush Front Wheel Module j Vacuum Guard Left Side Brush ex Right Side Brush Module E iji Nis Right Wheel Module BN i J L S Lat p Fan Module Top Body Dust Bin Module 15 Troubleshooting Battery Installation and Replacement A Remove two screws from battery cover with screw driver B Open the battery cover C Take out the
6. conds it will go into Sleep mode Note A Please keep the power switch on If not it will not operate B If power switch is turned off scheduling data will be erased Caution Before charging the cleaner please make sure the power switch is turned on otherwise the cleaner can not be charged Manual Charge Battery A Plug adapter power cord to unit power socket first and plug AC adapter to wall outlet next B Connect charging base with AC adapter to wall outlet to power on Press HOME button on cleaner unit or remote control to make cleaner return to charging base Beye hi ry ie tel 60 z NO Note A Turn on power switch before start to charge cleaner battery B Whe cleaner is charging display panel will show 1111 and repeat from right to left C Before first use charge the robot for 12 hours When charging is finished display panel will show FULL D Before first time use let the cleaner do cleaning until battery is used up E i I E After battery uses up recharge the cleaner as soon as possible F If the cleaner is not used for long time please turn the power switch off CLEAN G Do not operate cleaner while it is charging Auto charging The cleaner will automatically return to self charging base when cleaning is done or battery is low Note When battery is low display panel will show Lo Please keep self charging base plug in otherwise cleaner will not find the ba
7. e Right Wheel Module Left Wheel Module Bottom Cover Mop Cover Dust Bin Power Switch and Socket Dust Bin Primary Filter HEPA Filter HEPA Filter Frame Product Parts Charging Station and Virtual Blocker Infrared Signal Transmitter Signal Light Top Cover Charging Contacts Power Supply Socket Power Switch Infrared Signal Transmitter Signal Light Signal Window Side Cover Bottom Cover Installing virtual blocker battery Install two D type batteries After inserting the tip of the cover into the virtual blocker Into the slot push the other end to Lift the cover of the virtual blocker as shown close it until it clicks into place Note Take out the batteries if you wont use virtual blocker for long period of time 9 Product Parts Remote Control Unit fT Home button CD Scheduling button 6 Spot button lt gt Directional Buttons E Clean Power button 3 Edge button Use the remote control to wirelessly control the cleaner unit Make sure the unit is switched on before using the remote Point the remote towards the unit and press button to control unit operation Install one coin type battery into remote control unit Do not use remote near self charging base or virtual blocker Product Parts Unit Display Panel Illustration Display Illustration 88 88 numeric display Shows timer
8. lean while product is charging Do not over bend or put large weight on the power cord 8 This product is for indoor use and clean dry surface floor only 9 Do not sit on top of this product or attach an object on the top of it Do not use this product in wet or moist environment any environment with liquid Before use remove damagable objects glass textiles papers etc that can get caught in the cleaner s brush or vacuum intake Do no place this product where it is easy to drop off tables chairs etc Turn off the power switch during transportation or when you don t need to use this product for a long time Before charge battery make sure that the adapter and outlet are properly connected in right sequence to avoid sparks To avoid injury inform all people in the house that the unit is doing cleaning Do not use this product when dust bin is full Use this product in temperatures between 0 C and 40 C 32 F and 104 F Do not place this product in high temperature environment Remove battery from unit before recycle or scrap unit Disconnect AC adapter before removing the battery The battery should be properly disposed NOTE Do not allow children to operate this product unless they are supervised by an adult Product Features Powerful Suction 4 Intelligent Suction Adjustment Powerful suction Suction power of this product reaches 25 W ensuring that even tiny dust on the floor will be cleaned tho
9. out dust bin top cover and take out primary filter E Empty dust bin and wipe the dust F Wash dust bin with water Clean filters with cleaning brush tool DO NOT wash it with water Note 1 Clean dust bin module when T and icons are flashing on the display panel 2 Do not wash HEPA filter and replace it after one year of usage G Install primary filter and HEPA filter into dust bin Note 1 Install both HEPA and primary filters when they are dry 2 Do not place HEPA and primary filters directly in the sun H Close dust bin cover and install it into main unit Note Dust bin and filters including HEPA and filter could be replaced if needed 12 Product Maintaining Clean Sensors Wipe the sensor window and auto charging sensors with cleaning tool or a soft dry cloth Clean charging contacts on self charging base Note Never let water thinner etc directly touch the sensor window Assembly 8 Disassembly The Mop Reverse the cleaner tear out the mop unplug the fastener at the bottom of the cleaner to release the trailing bar refer to figure A and B you can assemble it as before disassembly Don t use the mop and trailing bar on the carpet or uneven ground 13 Troubleshooting Error Codes Chart Error code will show on display panel if there is a problem with the cleaner Remove hair and debris from the cleaner s left Left wheel error wheel Push it in and out and
10. roughly Intelligent Suction Adjustment This product will adjust its suction power according to the different floor types lt will clean the floor more effectively and also save power consumption User Friendly Design a 9 a UN Easy operation mij Voice message guidance and touch screen operations Just touch CLEAN key to start cleaning floor Wash Dust Bin Empty and wash dust bin with water regularly for cleaning effectiveness Four Cleaning Modes Four cleaning modes are provided to meet your needs 1 Auto cleaning mode The cleaner will clean and vacuum the floor automatically and adjust its cleaning routine based on its environment 2 Spot cleaning mode The cleaner will spend more time to clean dirty areas 3 Edge cleaning mode The cleaner will clean the edge and corner of walls 4 Scheduling mode You can schedule the cleaner to start cleaning at pre defined time 2 Product Parts Main unit and acceccories No Self Charging Base Remote Control battery included No ME Virtual Blocker battery not included AC Adapter MEN Cleaning Brush Tool Mop MEN Spare Side Brushes a o HEPA Filter 10 User Manual Product Parts Main Unit and Dust Bin Infrared Signal Receiver Bumper Main Pad Cover Ha MES Front Wheel Auto Charging Sensor 77_ fi Left Side Brush gt Battery Cover UV Right Side Brush Vacuum Intak
11. se to do auto battery charging 8 Product Operations Starting up Pause Sleeping Starting up A Make sure the power switch is on B Press CLEAN on the cleaner unit or remote control unit to start cleaning Note If cleaner is in sleeping mode press CLEAN button to wake up the cleaner The press CLEAN for a second time the cleaner starts cleaning automatically Changing modes Changing modes while unit is cleaning A Press PLAN CLEAN or HOME on cleaner or CLEAN on remote control to pause the current mode B Select new mode you wish to use Note When cleaner is paused press CLEAN on cleaner or remote to resume cleaning Sleep mode To make cleaner go into sleep mode A Cleaner will go into sleep mode if it does not receive any commands for 20 seconds B Otherwise press CLEAN on cleaner for 3 seconds Note Turn off the power switch if you are not using the cleaner for a long period of time Product Operations Scheduling You can schedule the cleaner to do cleaning at pre defined time every day There is no real time clock setting function You can set schedule cleaning time hh mm hours and minutes delay time from current time on your clock Time delay can be set up to 24 hours For example it is 9 00AM on your clock you set 6 30 delay time on the cleaner and the cleaner will start cleaning after 6 hours and 30 minutes which is 3 30PM The cleaner will start cleaning at 3 30PM every day until
12. unit power switch is turned off How to set cleaning delay time hh mm On cleaner unit A Press to enter scheduling mode the hours on 88 88 on LED display will flash B Press and ES to increase or decrease hours C Press to move from hours to minutes D Press and to increase or decrease minutes E Press to finish scheduling F To cancel scheduling keep pressing for 5 seconds in scheduling mode and delay time will be erased On remote control unit A Press Gon to wake up cleaner unit then press BD the hours on 88 88 on LED display will flash 44 a B Press button to to increase or decrease hours C Press Dr or 4 gt to move from from hours to minutes D Press 3 button to increase or decrease minutes E Press cen to finish scheduling F To cancel scheduling set hours and minutes on LED display to 00 00 in scheduling mode 10 Product Operations Cleaning mode Auto Cleaning Mode The cleaner will clean the area and adjust its cleaning routine according to its environment Note Press CLEAN on cleaner or remote to start auto cleaning mode Spot Cleaning Mode Place cleaner near dirty area Press SPOT to start cleaning and press CLEAN to stop 5 Note gt Spot cleaning makes the cleaner spend more time cleaning a dirty area Spot cleaning mode will stop once the area is clean Edge Cleaning
Download Pdf Manuals
Related Search