Installation Manual - Bosch Security Systems
Contents
1. Figure 3 3 Camera Box Hinge Alignment 6 Push and hold the top hinge and remove the junction box AM18 Q0663 1 0 2013 09 Installation manual Bosch Security Systems DINION imager 9000 HD Installation en 21 3 4 Mount the Junction Box S DELLE Le Qe Pau Figure 3 4 Interior of the Junction Box 1 Decide which holes in the junction box to use to insert the cables the holes in the bottom of the box the holes in the back of the box or the holes in the side of the box Remove the seals from the holes you will be using Using the wall mount bracket as a template mark the mounting holes Drill pilot holes at each marked point Align the mounting holes of the wall mount bracket with the holes drilled in the wall Using a socket wrench and a 14 mm 9 16 in socket not supplied screw the first 1 4 9 x 2 M7 0 35 x 50 lag bolt not supplied with 12 mm 1 2 in washer not supplied into the stud Repeat step 8 to attach the three remaining lag bolts Attach the appropriate NPS watertight pipe fittings not supplied to the bottom or back holes of the junction box through which to run the cables Bosch Security Systems Installation manual AM18 Q0663 1 0 2013 09 22 en Installatio2. AM18 Q0663 1 0 2013 09 Installation manual Bosch Security Systems DINION imager 9000 HD Installation en 19 3 2 2 Inserting the 3D diffuser 1 Unscrew the four captive screws beneath the illuminator at the front of the unit item 2 Figure 3 2 3D Diffuser 2 Using the captive screws remove the 3D diffuser holder 3 Insert the 3D diffuser into the slit in the gasket on the 3D diffuser holder Ensure that the diffuser is inserted into the camera housing with the sticker side facing the LED array It is important that the diffuser is oriented with the sticker side surface facing the LED array or IR performance will be lost 4 Insert the diffuser and holder assembly securely into the camera housing 5 Tighten the four captive screws to seal the unit Bosch Security Systems Installation manual AM18 Q0663 1 0 2013 09 20 en installation DINION imager 9000 HD 3 3 Unattach Junction Box Before mounting the junction box remove it from the camera assembly 1 Use an allen key to loosen the two screws and open the junction box 2 Loosen the slotted screws of the input output terminal block 7 pin and the slotted screws of the power terminal block 2 pins 3 Use two wrenches to remove the BNC connector from the bracket 4 Disconnect the Ethernet connection 5 Compress the bottom hinge pin by pushing the pin lever downward and rotating it behind the hinge pin stop
3. 4 Camera Set up Configuration of the camera is carried out via the network using a web browser Use the browser to configure the camera settings including lens zoom focus and IR LED power intensity To position the camera use the controls on the rear to start the installation wizard on the CVBS service output 4 1 Rear controls 4 1 1 Accessing the control panel 1 Unscrew the four captive screws of the access panel on the rear of the camera housing item 1 in the figure Figure 4 1 Rear camera housing with access panel 2 Open the access panel NOTICE Remember to tighten the captive screws on the panel when you finish the adjustments to seal the unit AM18 Q0663 1 0 2013 09 Installation manual Bosch Security Systems DINION imager 9000 HD Camera Set up en 27 4 1 2 Control panel Controls and sockets are located behind the access panel at the rear of the camera housing e J 1 B microSD Men Reset TV out ttt 200 MicroSD card slot Insert a microSD card into the slot 2 Menu button Use this button to start the field of view installation wizard 3 Reset button Restores a previous version of the firmware if uploading a new version fails With the power on press and hold the reset button for more than 10 seconds to restore the factory def
4. Because the ISDN circuits are treated like telephone network voltage avoid connecting the SELV circuit to the Telephone Network Voltage TNV circuits Video loss Video loss is inherent to digital video recording therefore Bosch Security Systems cannot be held liable for any damage that results from missing video information To minimize the risk of lost digital information Bosch Security Systems recommends multiple redundant recording systems and a procedure to back up all analog and digital information FCC amp ICES compliance FCC Information U S A and Canada This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference AM18 Q0663 1 0 2013 09 Installation manual Bosch Security Systems DINION imager 9000 HD Safety en 9 1 5 to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or
5. does not operate normally or has dropped When servicing power shall be disconnected 1 3 Important notices Accessories Do not place this unit on an unstable stand tripod bracket or mount The unit may fall causing serious injury and or serious damage to the unit Use only with the cart stand tripod bracket or table specified by the manufacturer When a cart is used use caution and care when moving the cart apparatus combination to avoid injury from tip over Quick stops excessive force or uneven surfaces may cause the cart unit combination to overturn Mount the unit per the manufacturer s instructions All pole power switch Incorporate an all pole power switch with a contact separation of at least 3 mm in each pole into the electrical installation of the building If it is needed to open the housing for servicing and or other activities use this all pole switch as the main disconnect device for switching off the voltage to the unit Camera signal Protect the cable with a primary protector if the camera signal is beyond 140 feet in accordance with NEC800 CEC Section 60 Bosch Security Systems Installation manual AM18 Q0663 1 0 2013 09 6 en Safety DINION imager 9000 HD CAUTION This product has been tested according to standard CIE IEC 62471 2006 Photobiological safety of lamps and lamp systems and found to meet Risk Group 2 for exposure limit 4 3 7 Infrare
6. more of the following measures reorient or relocate the receiving antenna increase the separation between the equipment and receiver connect the equipment into an outlet on a circuit different from that to which the receiver is connected consult the dealer or an experienced radio TV technician for help Intentional or unintentional modifications not expressly approved by the party responsible for compliance shall not be made Any such modifications could void the user s authority to operate the equipment If necessary the user should consult the dealer or an experienced radio television technician for corrective action The user may find the following booklet prepared by the Federal Communications Commission helpful How to Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington DC 20402 Stock No 004 000 00345 4 FCC Information Informations FCC et ICES mod les utilis s aux Etats Unis et au Canada uniquement Suite a diff rents tests cet appareil s est r v l conforme aux exigences impos es aux appareils num riques de classe B en vertu de la section 15 du r glement de la Commission f d rale des communications des Etats Unis FCC et en vertu de la norme CES 003 d Industrie Canada Ces exigences visent a fournir une protection raisonnable contre les interf rences nuisibles lorsque l appareil est utilis dan
7. Corner mount kit optional Mast mount kit optional Quick Install Guide this booklet Product CD with complete User Manual Ble e User Supplied Parts Quantity Item 4 Lag bolts 1 4 9 x 2 M7 0 35 x 50 with 1 2 in head 4 12 mm 1 2 in washers 2 20 mm 3 4 in NPS watertight pipe fittings OR 15 mm 1 2 in NPS watertight pipe fittings Stranded wire AWG 16 to 22 OR Solid wire AWG 16 26 Metal conduit for protection of power cables and input output cables Mounting hardware such as a corner mount adapter or pole mount adapter available separately from Bosch AM18 Q0663 1 0 2013 09 Installation manual Bosch Security Systems DINION imager 9000 HD Planning en 13 Required Tools User supplied 2 5 mm 0 1 in straight blade screwdriver Socket wrench 14 mm 9 16 in socket Drill 5 5 mm 7 32 in drill bit WARNING Important mounting instructions This apparatus must be securely attached to the wall in accordance with these installation instructions Failure to follow installation instructions may result in injury or death CAUTION Ensure that the selected location is protected from falling objects accidental contact with moving objects and unintentional interference from personnel Follow all applicable building codes CAUTION The camera is designed to be installed on static structures using t
8. DINION imager 9000 HD NAI 90022 BOSCH DINION imager 9000 HD Table of Contents en 3 Table of Contents 1 Safety 4 1 1 Safety precautions 4 1 2 Important safety instructions 4 1 3 Important notices 5 1 4 FCC amp ICES compliance 8 1 5 FCC Information 9 1 6 CSA certification Disclaimer 10 2 Planning 12 2 1 Pre installation Checklist 14 3 Installation 16 3 1 Overview of Installation Steps 16 3 2 Select Tilt and Width of Illumination Beam 17 3 2 1 Changing the angle of IR LED tilt 18 3 2 2 Inserting the 3D diffuser 19 3 3 Unattach Junction Box 20 3 4 Mount the Junction Box 21 3 5 Route Wires and Attach Connectors 22 3 5 1 Input Output Connections 23 3 6 Attach Camera to Junction Box 24 4 Camera Set up 26 4 1 Rear controls 26 4 1 1 Accessing the control panel 26 4 1 2 Control panel 27 4 2 Camera positioning and field of view 28 4 2 1 Making Pan Adjustments 28 4 2 2 Making Tilt Adjustments 28 4 3 Using the install wizard 30 4 3 1 Adjustment procedure 30 Bosch Security Systems Installation manual AM18 Q0663 1 0 2013 09 A en Safety DINION imager 9000 HD 1 1 db Safety Safety precautions DANGER High risk This symbol indicates an imminently hazardous situation such as Dangerous Voltage inside the product If not avoided this will result in an electrical shock serious bodily injury or death WARNING Medium risk Indicates a potentially hazardous s
9. ICE Both hinge pins must be fully compressed to open unlock the hinges of the camera arm and before proceeding to step 3 3 While continuing to hold the top hinge pin open and align the top and bottom hinges of the camera arm to their mating points on the junction box 4 Once you have aligned the hinges release the top hinge pin to engage its mating hinge on the junction box and AM18 Q0663 1 0 2013 09 Installation manual Bosch Security Systems DINION imager 9000 HD Installation en 25 then release the bottom hinge pin from the hinge pin stop to lock the camera arm to the junction box Put the input output terminal block on the bracket and tighten the two slotted screws Put the power terminal block on the bracket and tighten the two slotted screws Reattach the network cable from the camera to the connector in the junction box Reattach the BNC connector from the camera to the bracket in the junction box CAUTION The ITE is to be connected only to PoE networks without routing to the outside plant The camera can accept power from the 12 VDC 24 VAC power input or from the Ethernet input Ensure that the camera receives power from only one source 9 Attach an Ethernet cable Cat 5e or Cat 6 maximum distance 100 m 328 ft to the connector in the junction box Bosch Security Systems Installation manual AM18 Q0663 1 0 2013 09 26 en Camera Set up DINION imager 9000 HD
10. Q0663 1 0 2013 09 Installation manual Bosch Security Systems DINION imager 9000 HD Camera Set up en 29 Figure 4 2 Example orientation Camera rotated 90 degrees left pointing up 44 degrees From left front view side view back view ea Figure 4 3 Example orientation Camera rotated 90 degrees right point ing down 48 degrees From left front view side view back view Bosch Security Systems Installation manual AM18 Q0663 1 0 2013 09 30 en Camera Set up DINION imager 9000 HD 4 3 4 3 1 Using the install wizard The Menu button on the control panel is used to access the camera install wizard When there is a choice in the wizard the options are selected by either a short press less than 2 s ora long press more than 2 s of the button The wizard handles the following functions Lens identification Image orientation Zoom and focus adjustment conditions Auto focus Analog output Run the wizard to select orientation and field of view zoom Note The zoom and focus are adjusted again later via the web browser This optimizes picture sharpness in both bright and low level lighting Adjustment procedure If you have set up the camera an
11. S application and Canadian Electrical Code Part CSA C22 1 for CAN application and in accordance with local country codes for all other countries CSA Certified UL Listed CLASS 2 power adapters must be used in order to comply with electrical safety standards Branch circuit protection incorporating a 20 A 2 pole Listed Circuit Breaker or Branch Rated Fuses are required as part of the building installation A readily accessible 2 pole disconnect device with a contact separation of at least 3 mm must be incorporated Determine the location and distance for the junction box based on its voltage and current consumption Use only UL listed liquid tight strain reliefs for conduits to the junction box to ensure that water cannot enter the box You must use 3 4 in 20 mm NPS watertight conduits and fittings AM18 Q0663 1 0 2013 09 Installation manual Bosch Security Systems DINION imager 9000 HD Planning en 15 3 Route all rough wiring including power audio ethernet and alarms I O 4 Select the appropriate mounting kit to use depending on the location of the camera The camera is intended to be mounted securely to a wall using the mounting holes in the junction box Bosch Security Systems Installation manual AM18 Q0663 1 0 2013 09 16 enl installation DINION imager 9000 HD 3 Installation CAUTION Installation must be made by qualified service personnel and must conform to the National E
12. The camera is delivered with the 25 mm screw in place so for this type of application the screw does not have to be changed The 3D diffuser is recommended for wide field of view applications With the 3D diffuser the resulting beam angle is 42 H x 20 V to cover all the horizontal field of view FOV of the widest focal length of 10 mm application Without the 3D diffuser the beam angle is 10 H x 10 V which provides the longest distance detection distance The camera is delivered with the diffuser in place so for this type of application it does not have to be inserted Bosch Security Systems Installation manual AM18 Q0663 1 0 2013 09 18 enl installation DINION imager 9000 HD 3 2 1 Changing the angle of IR LED tilt NOTICE Do not discard the additional LED tilt set screw supplied It may be required to adjust the angle of LED tilt 1 Unscrew the current tilt screw located between the camera window and the IR LED window at the front of the camera ft Figure 3 1 l Slot for set screw for adjusting angle of LED tilt 2 Screw the selected screw as far as possible into the hole The screw must be tightened completely to obtain the desired angle WARNING The LED Tilt Set screw must be inserted completely so that the integrated O ring makes a seal with the camera housing If the screw is not completely inserted the water tightness of the camera will be compromised
13. aults 4 Service video output 2 5 mm jack provides a CVBS signal for installation purposes only Bosch Security Systems Installation manual AM18 Q0663 1 0 2013 09 28 en Camera Set up DINION imager 9000 HD 4 2 Camera positioning and field of view To help position the camera and set the field of view 1 z Connect a monitor to the 2 5 mm jack using the optional monitor cable S1460 which provides a CVBS signal for installation purposes only Apply power to the camera After power up wait a little about 20 seconds Press the Menu button This enables the service video analog output Follow the instructions in Section 4 3 Using the install wizard Page 30 to position the camera While using the wizard the pan and tilt position can be adjusted as outlined below 4 2 1 Making pan adjustments 1 3 Using the 4 mm hex key loosen the bolts at the base of the U bracket to make the necessary pan adjustments When loosened adjust the camera to the desired pan angle Tighten the bolt to secure in place 4 2 2 Making tilt adjustments 1 MRON Using the 2 5 mm hex key unscrew the round caps where the bracket attaches to the camera housing to expose the bolts for tilt adjustment Using the 4 mm hex key loosen the bolts Make the necessary tilt adjustments Tighten the bolts to secure the camera in place Replace the round caps when you finish the adjustments AM18
14. d pressed the Menu button as described in Section 4 2 Camera positioning and field of view page 28 then you see the following on the monitor screen Lens type Focus Indicator 0 Po CONTINUE 180 ROTATE Timeout 300 lt press short gt lt press long gt The lens type is identified and shown on the screen The iris is opened to its maximum value AM18 Q0663 1 0 2013 09 Installation manual Bosch Security Systems DINION imager 9000 HD Camera Set up en 31 1 To rotate the image 180 press and hold the Menu button until the image flips Briefly press the Menu button to open the automatic motorized focus adjustment screen Briefly press the Menu button to set the focus and zoom defaults The progress is shown on the monitor When the initial focus adjustment is finished position the camera using the pan and tilt adjustments Briefly press the Menu button to start the automatic motorized focus adjustment Briefly press the Menu button again and again to scroll through the seven preset zoom positions The selection moves back when the last position is reached When you reach the desired zoom position use a long press of the Menu button to set the zoom position and to re focus If the camera is not correctly focussed press the Menu button for a longer time to restart the wizard If the camera is correctly focussed press the Menu button for a short time t
15. d radiation hazard exposure limits for the eye For other hazard exposure limits the product was found to be exempt Risk Group 2 is characterized in the standard as products generally do not pose a realistic optical hazard if aversion responses limit the exposure duration or where lengthy exposures are unrealistic Since there is no aversion response for IR avoid eye exposure Risk Group 2 sources do not pose an infrared radiation hazard for the eye within 10 s at distances beyond 200 mm or 8 inches The Exposure Hazard Value for the product ratio of the Exposure level to the Exposure limit is up to 10 ata test distance of 200 mm 8 inches The Hazard Distance distance beyond which the product falls into the exempt safe group is at most 640 mm 25 inches Note that typical use cases are well beyond the Hazard Distance When servicing the unit physically disconnect the power supply to avoid possible IR exposure to the eyes If physical disconnection is not possible use appropriate shielding to block the LED panel or use eye protection with a transmission of 10 or less at a wavelength of 850 nm Coax grounding Ground the cable system if connecting an outside cable system to the unit Connect outdoor equipment to the unit s inputs only after this unit has had its grounding plug connected to a grounded outlet or its ground terminal is properly connected to a ground source Disconnect the unit s input connectors from o
16. he specified mounting adapters It should not be installed in dynamic environments or on moving objects such as vehicles ships or elevators Select a suitable location that protects the camera from accidental damage tampering and environmental conditions exceeding the specifications of the camera Follow these mounting guidelines 1 Locate the camera such that it cannot be easily interfered with either intentionally or accidentally 2 Select a smooth flat mounting surface that can support the combined weight of the camera and mounting hardware under all expected conditions of vibration and temperature Recommended mounting height is at least 4 m 13 ft however optimal conditions will vary with the specific installation environment Bosch Security Systems Installation manual AM18 Q0663 1 0 2013 09 14 en Planning DINION imager 9000 HD 2 1 Pre installation Checklist WARNING This installation must be made by a qualified service person and must conform to all local codes WARNING CSA Certified UL Listed CLASS 2 or Certified PoE rated 42 5 VDC to 57 VDC 600 mA 34 20 W max for IP models power adapters must be used in order to comply with electrical safety standards WARNING Power and I O cabling must be routed separately inside different permanently earthed metal conduits GPP WARNING Install external interconnecting cables in accordance with NEC ANSI NFPA70 for U
17. ituation If not avoided this could result in minor or moderate bodily injury CAUTION Low risk Indicates a potentially hazardous situation If not avoided this could result in property damage or risk of damage to the unit NOTICE This symbol indicates information or a company policy that relates directly or indirectly to the safety of personnel or protection of property 1 OB Bb D Important safety instructions Read follow and retain all of the following safety instructions Heed all warnings on the unit and in the operating instructions before operating the unit 1 Clean only with dry cloth 2 Do not block any ventilation openings Install in accordance with manufacturer s instructions 3 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat AM18 Q0663 1 0 2013 09 Installation manual Bosch Security Systems DINION imager 9000 HD Safety en 5 4 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the power where they exit from the apparatus 5 Use only attachments accessories specified by the manufacturer 6 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged ina way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus
18. lectrical Code and all applicable local codes WARNING IMPORTANT MOUNTING INSTRUCTIONS The camera must be attached securely to the wall in accordance with these installation instructions Failure to follow installation instructions may result in injury or death The camera has been evaluated for wall mounting through the mounting holes in the junction box using the following hardware secured into a 2 x 4 stud under 1 2 in drywall Four 4 Lag bolts 1 4 9 x 2 M7 0 35 x 50 with 1 2 in head Four 4 12 mm 1 2 in flat washers The camera has not been evaluated for safety requirements using other mounting kits 3 1 Overview of Installation Steps Follow these steps in sequence to mount the camera to a wall 1 Six Ge kb Select tilt and width of illumination beam Unattach the junction box Mount the junction box Route wires and attach connectors Attach camera to junction box AM18 Q0663 1 0 2013 09 Installation manual Bosch Security Systems DINION imager 9000 HD Installation en 17 3 2 Select Tilt and Width of Illumination Beam Before mounting the camera decide the application As a general guideline the IR LED tilt angle should be raised above the axis of the camera to reduce overexposure in the foreground Use the 31 mm screw for general area surveillance targets closer to the camera Use the 25 mm screw for other use cases such as monitoring a perimeter
19. led with great care and the information it contains has been verified thoroughly The text was complete and correct at the time of printing The ongoing development of products means that the content of the user guide can change without notice Bosch Security Systems accepts no liability for damage resulting directly or indirectly from faults incompleteness or discrepancies between the user guide and the product described More information For more information please contact the nearest Bosch Security Systems location or visit www boschsecurity com Bosch Security Systems Installation manual AM18 Q0663 1 0 2013 09 12 en Planning DINION imager 9000 HD 2 Planning This equipment should be unpacked and handled carefully If an item appears to have been damaged in shipment notify the shipper immediately Verify that all the parts listed in the Parts List below are included If any items are missing notify your Bosch Security Systems Sales or Customer Service Representative The original packing carton is the safest container in which to transport the unit and must be used if returning the unit for service Save it for possible future use Parts Included with the Product Quantity Item 1 IR Imager camera Cable managed pan tilt bracket Junction box Sunshield 3D Diffuser Hex keys 1x 5 mm 1x 2 5 mm 1x 4 mm N wl ele eye Screws for adjusting the LED tilt 1x 25 mm 1x 31 mm
20. n DINION imager 9000 HD NOTICE You must use the appropriate UL listed NPS watertight conduits and fittings to ensure that water cannot enter the junction box Use 20 mm 3 4 in NPS fittings for the holes on the bottom and back of the box Use 15 mm 1 2 in NPS fittings for the side holes 3 5 Route Wires and Attach Connectors 1 Route all video control and alarm wires through the conduit fitting to the junction box These wires must be routed through a permanently earthed metal conduit Route the power lines 24 VAC 12 VDC through the conduit fitting to the junction box Use stranded wire AWG 16 to 22 or solid wire AWG 16 to 26 These wires must be routed through a permanently earthed metal conduit Cut and trim all wires with sufficient slack to reach their connector terminals in the box but not so long as to be pinched about 5 mm 0 2 in of insulation Loosen the screws of the 2 pin terminal block and attach the incoming power wires Tighten the screws of the 2 pin terminal block Loosen the slotted screws of the 7 pin input output terminal block attach the wires according to the pin definition table and retighten the screws NOTICE For a DC supply the polarity is important Incorrect polarity does not damage the camera but will not allow the camera to switch on If input voltage is not within the specified range or has incorrect polarity DC only the voltage indicator a yell
21. ned to respect the environment as much as possible Fuse rating For protection of the device the branch circuit protection must be secured with a maximum fuse rating of 16A This must be in accordance with NEC800 CEC Section 60 Moving Disconnect the power before moving the unit Move the unit with care Excessive force or shock may damage the unit and the hard disk drives Outdoor signals The installation for outdoor signals especially regarding clearance from power and lightning conductors and transient protection must be in accordance with NEC725 and NEC800 CEC Rule 16 224 and CEC Section 60 Bosch Security Systems Installation manual AM18 Q0663 1 0 2013 09 8 en Safety DINION imager 9000 HD 1 4 Permanently connected equipment Incorporate a readily accessible disconnect device external to the equipment Pluggable equipment Install the socket outlet near the equipment so it is easily accessible Power resupply If the unit is forced to power down due to exceeding the specified operating temperatures disconnect the power cord wait for at least 30 seconds and then reconnect the power cord Power lines Do not locate the camera near overhead power lines power circuits or electrical lights nor where it may contact such power lines circuits or lights SELV All the input output ports are Safety Extra Low Voltage SELV circuits SELV circuits should only be connected to other SELV circuits
22. o change the analog output Briefly press the Menu button again and again to select NTSC or PAL with the appropriate aspect ratio for your display or to swich the analog output OFF default When the selection is made use a long press of the Menu button to save the results The zoom and focus position is stored The iris is set to its original value The video service output is disabled The BNC video output is set to its selected state Note The wizard automatically disappears if not used for a whle Bosch Security Systems Installation manual AM18 Q0663 1 0 2013 09 Bosch Security Systems www boschsecurity com Bosch Security Systems 2013
23. orrective La brochure suivante publi e par la Commission f d rale des communications FCC peut s av rer utile How to Identify and Resolve Radio TV Interference Problems Comment identifier et r soudre les probl mes d interf rences de radio et de t l vision Cette brochure est disponible aupr s du U S Government Printing Office Washington DC 20402 Etats Unis sous la r f rence n 004 000 00345 4 1 6 CSA certification Disclaimer CSA has not tested the performance or reliability of the security or signaling aspects of this product CSA has only tested fire shock and or casualty hazards as outlined in CSA s Standard s for Safety for Closed Circuit Television Equipment UL 2044 CSA Certification does not cover the performance or reliability of AM18 Q0663 1 0 2013 09 Installation manual Bosch Security Systems DINION imager 9000 HD Safety en 11 1 7 the security or signaling aspects of this product CSA MAKES NO REPRESENTATIONS WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT Bosch notices Copyright This manual is the intellectual property of Bosch Security Systems and is protected by copyright All rights reserved Trademarks All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly NOTE This manual has been compi
24. ow LED in the front window turns on to indicate this condition 7 Connect the incoming Ethernet cable to the RJ45 connector supplied in the camera junction box AM18 Q0663 1 0 2013 09 Installation manual Bosch Security Systems DINION imager 9000 HD Installation en 23 3 5 1 Input Output Connections Figure 3 5 Terminal Block for Input Output Connections Label Description Wire Color 1 INC Not connected 2 V1 Alarm output 2 Yellow 3 V2 Alarm output 1 White 4 T1 Audio output Gray 5 T2 Audio input Brown 6 D1 Alarm input 1 Orange 7 D2 GND Black 8 12 VDC 24 VAC Red 9 _ GND DC 24 VAC Green Bosch Security Systems Installation manual AM18 Q0663 1 0 2013 09 24 en Installation DINION imager 9000 HD 3 6 Attach Camera to Junction Box The bottom hinge pin of the camera arm has a stop to hold the hinge open while attaching the arm to the junction box DANGER Serious injury or death can occur if the hinge pins of the camera arm are not fully engaged locked to the junction box Use caution before releasing the camera arm 1 Compress the bottom hinge pin by pushing the pin lever downward and rotating it behind the hinge pin stop OO Figure 3 6 Camera Box Hinge Alignment 2 Open the top hinge by pushing and holding up the pin lever NOT
25. s le cadre d une installation r sidentielle Cet appareil g n re utilise et met de l nergie de radiofr quences et peut en cas d installation ou d utilisation non conforme aux instructions engendrer des Bosch Security Systems Installation manual AM18 Q0663 1 0 2013 09 10 en Safety DINION imager 9000 HD interf rences nuisibles au niveau des radiocommunications Toutefois rien ne garantit l absence d interf rences dans une installation particuli re Il est possible de d terminer la production d interf rences en mettant l appareil successivement hors et sous tension tout en contr lant la r ception radio ou t l vision L utilisateur peut parvenir liminer les interf rences ventuelles en prenant une ou plusieurs des mesures suivantes Modifier l orientation ou l emplacement de l antenne r ceptrice loigner l appareil du r cepteur Brancher l appareil sur une prise situ e sur un circuit diff rent de celui du r cepteur Consulter le revendeur ou un technicien qualifi en radio t l vision pour obtenir de l aide Toute modification apport e au produit non express ment approuv e par la partie responsable de l appareil est strictement interdite Une telle modification est susceptible d entra ner la r vocation du droit d utilisation de l appareil Au besoin l utilisateur consultera son revendeur ou un technicien qualifi en radio t l vision qui proc dera une op ration c
26. utdoor equipment before disconnecting the grounding plug or grounding terminal AM18 Q0663 1 0 2013 09 Installation manual Bosch Security Systems DINION imager 9000 HD Safety en 7 Follow proper safety precautions such as grounding for any outdoor device connected to this unit U S A models only Section 810 of the National Electrical Code ANSI NFPA No 70 provides information regarding proper grounding of the mount and supporting structure grounding of the coax to a discharge unit size of grounding conductors location of discharge unit connection to grounding electrodes and requirements for the grounding electrode Disposal Your Bosch product was developed and manufactured with high quality material and components that can be recycled and reused This symbol means that electronic and electrical appliances which have reached the end of their working life must be collected and disposed of separately from household waste material Separate collecting systems are usually in place for disused electronic and electrical products Please dispose of these units at an environmentally compatible recycling facility per European Directive 2002 96 EC Electronic Surveillance This device is intended for use in public areas only U S federal law strictly prohibits surreptitious recording of oral communications Environmental statement Bosch has a strong commitment towards the environment This unit has been desig
Download Pdf Manuals
Related Search