Home

Skyus-E User Manual

1. FW Skyus E User Manual Specifications Hardware Input Voltage e 9 36V DC AC DC adapter e Typical 12V 0 32A 3 84W e Max 12V 1 56A 18 75W Power C ti OEE OM UMELO e Low Power 8V 0 02A 0 16W 3G module running Skyus E Interface with Internet activity e Operating Temperature 20 C to 60 C 4 F to 140 F e Storage Temperature 40 C to 85 C 40 F to 185 F 5 W x 2 H x 5 D Approximate includes mounting plate Skyus E 0 554 kg 1 20 Ibs EYES AYE NYETA ee Plate 0 249 kg 0 55 Ibs Mounting Tool free mounting of Tool free mounting of Skyus E to mounting plate sold separately E to mounting plate sold separately One 10 100 Ethernet RJ 45 Ethernet switch recommended for expansion if Data Interface Ka Primary Cellular 50 Ohm SMA SubMiniature version A female MIMO if 4G LTE Receive Diversity if 3G 50 Ohm SMA female GPS 50 Ohm SMA female LEDs Power x1 Activity x1 Signal Strength x4 Signal LED color shows cellular connection type Blue 4G Green 3G Amber 2G No lights No Connection Upgrade Kit Skyus E upgrade kit for easy installation of existing Skyus modules Environmental Antenna Connections Cellular LTE with fallback to HSPA HSPA UMTS EDGE GPRS EVDO 1xRTT depending on an the KIT aaa module used Carriers OO Sprint Verizon AT amp T T Mobile TG Verizon AT amp T T Mobile Bands bands SRE the Skyus Specificati
2. gt C ff 5 192 168 66 1 Socket Activity Logging Activity CARRIER 4G LTE Status fe Network GPO IGS Crossroads Connection GPS Configuration SOB oe maa s LYT w Broadband Set As Current Profile gt Administration we A Custom N System Logging NG 12gold Set As Current Profile gt Alerts 0 Notifications 9 Standard read only W 5 27 2015 2 46 00 PM Broadband Use As Custom APN gt QOS has been 10 or less for 2 minutes 12gold Use As Custom APN gt W 5 27 2015 2 46 40 PM QOS has been 10 or less for 2 minutes Add APN Profile W 5 27 2015 2 47 20 PM User defined QOS has been 10 or less for 2 minutes FW eaw AXIOM Copyright 2015 Feeney Wireless All Rights Reserved Figure 20 APN Tab Field Description Default Lists the default APN profile This is the APN that was assigned to the Skyus during the over the air Por process Custom Lists custom APN Lists custom APN profiles defined by the user defined by the user Standard read only Lists standard APN profiles which may be used as custom APN profiles Uar dennad Na oo APN profiles For private networking applications this option may e used 30 FW Skyus E User Manual Description Opens a dialog to create an APN profile Address APNName Authentication N fil Add APN Profile ame profile name PDPType ipv4 ppp ipv6 ipv4 ipv6 Password PrimaryDNS SecondaryDNS UserName Set As C
3. AW Skyus E loT Appliance User Manual Installation Configuration and Management FW Skyus E User Manual Preface Copyright 2015 Feeney Wireless LLC FW a Novatel Wireless company All rights reserved This document may not be copied in part or otherwise reproduced without prior written consent from Feeney Wireless except where specifically permitted under US and International copyright law Disclaimer The information in this document is subject to change without notice Feeney Wireless FW assumes no responsibility for inaccuracies or omissions and specifically disclaims any liabilities losses or risks personal or otherwise incurred as a consequence directly or indirectly of the use or application of any of the contents of this document For the latest documentation contact your local supplier or visit us online at www feeneywireless com This publication may contain examples of screen captures and reports used in daily operations Examples may include fictitious names or individuals and companies Any similarity to names and addresses of actual businesses or persons is entirely coincidental Patents and Trademarks The Skyus E incorporates technologies covered under U S Patents 8 706 104 8 670 897 and other patents pending Feeney Wireless and the FW logo are trademarks of Feeney Wireless LLC Skyus Skyus 3G Skyus 4G Skyus Global Skyus E Skyus DS CIRA CIRA X CIRA X2 Crossroads and Axiom are tradem
4. b Accompany it with a written offer valid for at least three years to give any third party for a charge no more than your cost of physically performing source distribution a complete machine readable copy of the corresponding source code to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange or c Accompany it with the information you received as to the offer to distribute corresponding source code This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer in accord with Subsection b above The source code for a work means the preferred form of the work for making modifications to it For an executable work complete source code means all the source code for all modules it contains plus any associated interface definition files plus the scripts used to control compilation and installation of the executable However as a special exception the source code distributed need not include anything that is normally distributed in either source or binary form with the major components compiler kernel and so on of the operating system on which the executable runs unless that component itself accompanies the executable FW Skyus E User Manual If distribution of executable or object code is made by offering access to copy from a designated place then offering equivalent access to copy th
5. 3 Alerts 0 Notifications 4 5 27 2015 2 42 54 PM A System passwrd has not been changed 5 27 2015 2 43 20 PM QOS has been 10 or less for 2 minutes 5 27 2015 2 44 00 PM Connection State Carrier Connection Type IMEI IPv4 MAC Address Qos SIM System Temperature Signal Strength Up Time Input Voltage Up Carrier Name 4G LTE 359225050540152 10 132 5 209 1c ba 8c 9b 99 ca 12 dB 89014103277188507037 30 C 78 dBm 0 Hrs 5 Min 6 Sec 14600 mv QOS has been 10 or less for 2 minutes LI PW Copyright 2015 Feeney Wireless All Rights Reserved Powered by ax m Figure 9 Dashboard Tab Description Values Up Down Reports whether or not a connection to the cellular carrier is up or down The connection is reported as up if an IP address has been assigned and a ping ICMP check to a URL or IP as configured under Network gt Connection gt Ping URL or Alt Ping URL is successful Name of the cellular carrier in use such as AT amp T Sprint T Mobile Verizon etc Connection Status Connection Type Type of cellular connection such as 4G LTE and others IMEI IMEI number of the Skyus radio module The IMEI is often required when attempting to activate a Skyus with a cellular carrier WAN IP address of the Skyus E when connected to a cellular data network MAC address of the Skyus E Ethernet interface A MAC address is a unique id
6. Activity Logging Activity CARRIER 4G LTE Status Pro Network APN GPO IGS Connection GPS Configuration Enable Crossroads CM Administration ng YS i gt Server xrdl feeneywireless com System Logging i Alerts 0 Notifications 11 Back up Server ixrdl feeneywireless com KO Y 5 27 2015 2 47 20 PM QOS has been 10 or less for 2 Server Port 39759 minutes l 5 27 2015 2 48 00 PM Reporting Interval Every 30 Mins v QOS has been 10 or less for 2 minutes 5 27 2015 2 48 40 PM QOS has been 10 or less for 2 minutes FW Poved AXIOM Copyright 2015 Feeney Wireless All Rights Reserved Figure 22 Crossroads Tab Field Description Enable Crossroads Enables or disables Skyus E connection to Crossroads TN IP address of the Crossroads server This only needs to be supplied if the customer accesses Crossroads on a non FW server IP address of the Crossroads backup server This only needs to be supplied if Crossroads will be accessed on a non FW server Server Port Port number of the Crossroads server Drop down list to select the time interval for reporting Skyus E status to Crossroads Back up Server Reporting Interval Values Every 5 minutes Every 15 minutes Every 30 minutes Hourly 33 FW Skyus E User Manual Connection This tab provides the ability to set various connection quality and test parameters FW S
7. Alerts 0 Notifications 12 3 5 27 2015 2 48 00 PM QOS has been 10 or less for 2 minutes 5 27 2015 2 48 40 PM QOS has been 10 or less for 2 minutes 5 27 2015 2 49 25 PM QOS has been 10 or less for 2 minutes HG FW Powered by a m Copyright 2015 Feeney Wireless All Rights Reserved Figure 26 User Tab Description Opens a dialog to change a user s password e Old Password Enter the user s old password Change Password e New Password Enter the new password Passwords must be at least eight characters For security reasons it is a good idea to change the admin password Keep a record of the new password in a secure location Opens a dialog to add a new user e Username e Password Add New User e Level User Admin Admins can change Skyus E settings For users settings are read only All users should keep a record of their passwords in a secure location 37 FW Skyus E User Manual Settings This tab provides the ability to set the local and remote port number for access to the Skyus E Utility and create and manage setting profiles FW Skyus E Adminstration xy gt C ff 5 192 168 66 1 Socket Activity Logging Activity CARRIER 4G LTE Status FA User Firmware Configuration god Web Client Administration SK Local Port 80 Remote Port 8080 System Logging f System Settings Alerts 0 Notifications 13 na TimeZone UTC v
8. OpenSSL Toolkit http www openssl org 4 Thenames OpenSSL Toolkit and OpenSSL Project must not be used to endorse or promote products derived from this software without prior written permission For written permission please contact openssl core openssl org 5 Products derived from this software may not be called OpenSSL nor may OpenSSL appear in their names without prior written permission of the OpenSSL Project 6 Redistributions of any form whatsoever must retain the following acknowledgment This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit http www openssl org THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT AS IS AND ANY EXPRESSED OR IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE ARE DISCLAIMED IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT INDIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES LOSS OF USE DATA OR PROFITS OR BUSINESS INTERRUPTION HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY WHETHER IN CONTRACT STRICT LIABILITY OR TORT INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE This product includes cryptographic software written by Eric Young eay cryptsoft com Thi
9. Signal Strength LEDs will flash green when the reset occurs Access the Skyus E Interface You might have to refresh the browser if the log in screen still shows that the interface has timed out On the Configuration gt APN screen set the current APN profile to the Default The Skyus E will reset using the default APN profile This will take up to two minutes If the ignition sense line pin 3 on the power connector has not been properly implemented and IGS is enabled the Skyus E will shut down after the shutdown period Remove and reapply power to the Skyus E Log in to the Skyus E Interface as soon as possible disable IGS on the Configuration 5 GPO IGS screen and click Save 44 FW Skyus E User Manual Appendix B Mounting Plate Template Printed at full size the illustration below can be used to mark the center points of the four screw holes for installing the mounting plate After printing the template measure the distance between the holes to make sure the size is accurate as shown below NOTE Some print drivers will provide the option to fit to printer margins which may cause scaling To ensure that the size is accurate make sure to print to actual size 74 93 mm 2 95 in LA O N E E ioe O JT N 45 FW Skyus E User Manual Appendix C Swapping Modems The following instructions describe the procedure for swapping modems in the Skyus E enclosure For instructions on installing
10. W 5 27 2015 2 48 40 PM NTP Server www ntp org minutes Data Usage Threshold MB 0 QOS has been 10 or less for 2 O z W 5 27 2015 2 49 25 PM QOS has been 10 or less for 2 minutes Setting Profiles QOS has been 10 or less for 2 5 27 2015 2 50 01 PM minutes Save Current Settings O Restore Factory Defaults Upload Settings ayy Powered by P Copyright 2015 Feeney Wireless All Rights Reserved Figure 27 Settings Tab Field Description Web Client Local Port TCP port to access the Skyus E Utility from the LAN Default 80 Remote Port TCP port to access the Skyus E Utility from the WAN Default 8080 System Settings Time Zone Selects either UTC Universal Coordinated Time or a local time zone Enter the URL of the Network Time Protocol NTP server you want the Skyus E to use NTP Server and click Apply By default the Skyus E will obtain the current UTC time from the cellular network upon connecting Allows you to enter the upper threshold of your monthly data plan The system will Data Usage Threshold MB use this information to indicate what percentage of your data plan has been used by changing the color of the Activity LED see Activity LED 38 FW Skyus E User Manual Field Description Setting Profiles Sets the selected profile as the current profile to revert to in the event of a reset to Set Current Hi user defaults via eit
11. a Skyus modem into the Skyus E Retrofit kit see the Skyus E Retrofit Assembly Instructions The figure below shows how to access inside of the Skyus E in order to swap a Skyus radio module 1 Faceplate Screws x4 2 Faceplate 3 Skyus Radio Module 4 Pull Tab 5 Antenna Cable Clip 6 USB 7 Secondary Antenna 8 Primary Antenna 9 Skyus E Enclosure 10 Mounting Plate a a a Pd Figure 30 Skyus Modem Installation Single SIM Modem 1 Detach the Skyus E from the mounting plate 10 if it is attached 2 Access the inside of the Skyus E by removing the four screws 1 securing the faceplate 2 using a T8 Torx driver 3 Pull out the existing Skyus modem 3 using the red pull tab 4 Remove the antenna cable clip 5 5 Disconnect the USB 6 secondary antenna 7 and primary 8 antenna cables from the existing modem and attach them in the same order to the new modem When plugging in the USB cable make sure to position the pull tab over the connector for easy modem removal in the future SMA connectors should be tightened to 8 in Ibs using a torque wrench with a 5 16 bit Note The cable labeled FW8163 A is the Primary antenna cable and attaches to the outermost antenna connector on the Skyus module The cable labeled FW7837 A is the Secondary antenna cable and attaches to the innermost antenna connector on the Skyus module 6 For GPS models connect the GPS cable to the middle SMA connector not shown 7 Snap t
12. at all TERMS AND CONDITIONS FOR COPYING DISTRIBUTION AND MODIFICATION 0 This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License The Program below refers to any such program or work and a work based on the Program means either the Program or any derivative work under copyright law that is to say a work containing the Program or a portion of it either verbatim or with modifications and or translated into another language Hereinafter translation is included without limitation in the term modification Each licensee is addressed as you Activities other than copying distribution and modification are not covered by this License they are outside its scope The act of running the Program is not restricted and the output from the Program is covered only if its contents constitute a work based on the Program independent of having been made by running the Program Whether that is true depends on what the Program does 1 You may copy and distribute verbatim copies of the Program s source code as you receive it in any medium provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty keep intact all the notices that refer to this License and to the absence of any warranty and give any other recipients of the Program a copy of this License alo
13. been powered up since the last power cycle or reboot Amount of RAM in kilobytes present in the Skyus E The current version has 505 188 Total Memory KB of useable memory Amount of RAM free to the operating system Free Memory can be a useful point of Free Memory reference in troubleshooting Skyus E performance issues MAC address of the Skyus E Ethernet interface A MAC address is a unique identifier MAC Address oe and thus can be useful when creating MAC address filtering rules LAN IP The current IP address of the Skyus E Current WAN IP address of the device generally obtained from your carrier This is the WAN IP address you can use to contact the Skyus E from the Internet if your assigned IP is routable The number of times power has cycled on the Skyus E Configuration The Configuration page provides the ability to manage network settings create and manage APN profiles determine connection behavior enable general purpose output GPO and manage ignition sense IGS settings To access this page click Configuration in the navigation panel Information on this page is organized under four tabs Network APN Connection and GPO IGS 20 FW Skyus E User Manual Network This tab provides the ability to manage DHCP and LAN settings and add rules for the firewall port forwarding routing and MAC filtering FW Skyus E Adminstration x gt C ff 5 192 168 66 1 Socket Activity Logging Activity CAR
14. connection status From a computer connected to the Internet open a browser and enter the Skyus E IP address in the address bar The login page of the utility displays the state type and up time of the connection among other information See Skyus E Default Settings See Skyus E Administration Interface for complete information on monitoring configuring and managing your Skyus E 10 FW Skyus E User Manual Activity LED The Activity LED indicates both network activity and data usage The following table describes the Activity LED modes Note that indication of monthly data plan used is dependent upon configuring your data usage thresholds in the Skyus E configuration If this is not configured the Activity LED will default to blue LED Mode Color Description Intermittent flashing Skyus E transferring data Solid Blue 0 50 of the monthly data plan is used 51 85 of the monthly data plan is used 86 99 of the monthly data plan is used Solid Red 100 of the monthly data plan is used Signal Strength LEDs The Signal Strength LED array indicates both the strength of the cellular signal and the type of connection The array follows the standard 1 4 bar signal strength scheme with four bars indicating a strong signal The following table describes the Signal Strength LED modes LED Mode Color Description O bars lit No connection Resetting the Skyus E The Reset button on the Skyus E front panel perf
15. in reliance on consistent application of that system it is up to the author donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License 8 If the distribution and or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries so that distribution is permitted only in or among countries not thus excluded In such case this License incorporates the limitation as if written in the body of this License 51 FW Skyus E User Manual 9 The Free Software Foundation may publish revised and or new versions of the General Public License from time to time Such new versions will be similar in spirit to the present version but may differ in detail to address new problems or concerns Each version is given a distinguishing version number If the Program specifies a version number of this License which applies to it and any later version you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation If the Program does not specify a version number of this License you may choose any version ever
16. of the Software THE SOFTWARE IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM DAMAGES OR OTHER LIABILITY WHETHER IN AN ACTION OF CONTRACT TORT OR OTHERWISE ARISING FROM OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE WebSocket Version 0 5 1 WebSocket is an open source BSD license header only C library that implements RFC6455 The WebSocket Protocol It allows integrating WebSocket client and server functionality into C programs It uses interchangeable network transport modules including one based on C iostreams and one based on Boost Asio Boost Software License Version 1 0 August 17th 2003 Permission is hereby granted free of charge to any person or organization obtaining a copy of the software and accompanying documentation covered by this license the Software to use reproduce display distribute execute and transmit the Software and to prepare derivative works of the Software and to permit third parties to whom the Software is furnished to do so all subject to the following The copyright notices in the Software and this entire statement including the above license grant this restriction and the following disclaimer must be included in all copies of the So
17. technician for help DO NT Y Exposure to RF radiation To comply with FCC RF exposure compliance requirements for mobile configurations a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons Do not collocate or operate this device in conjunction with any other antenna or transmitter The TX module FCC ID depends on the Skyus module installed See the Skyus Specification Sheet or the Skyus DS Specification Sheet 42 FW Appendix A Troubleshooting Skyus E User Manual The majority of faults result from insufficient power or incorrect configuration Power supply and configuration should be the first things checked before more extensive troubleshooting begins Make sure the Skyus E and the internal Skyus module are properly installed according to the instructions in this manual or the Quick Start Guide before searching for other remedies One of the first things to establish is whether the device was working prior to the fault without any change to the hardware or software settings If the unit was working initially investigate power quality first Also look for signs of physical damage or tampering In many cases when a fault is detected it is still possible to log in to the Skyus E Interface Doing so will provide you with additional information about the unit that will help you to determine a remedy Fault Power LED is not lit No other LEDs are lit Cannot connect t
18. the modified work as a whole If identifiable sections of that work are not derived from the Program and can be reasonably considered independent and separate works in themselves then this License and its terms do not apply to those sections when you distribute them as separate works But when you distribute the same sections as part of a whole which is a work based on the Program the distribution of the whole must be on the terms of this License whose permissions for other licensees extend to the entire whole and thus to each and every part regardless of who wrote it Thus it is not the intent of this section to claim rights or contest your rights to work written entirely by you rather the intent is to exercise the right to control the distribution of derivative or collective works based on the Program In addition mere aggregation of another work not based on the Program with the Program or with a work based on the Program on a volume of a storage or distribution medium does not bring the other work under the scope of this License 3 You may copy and distribute the Program or a work based on it under Section 2 in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following a Accompany it with the complete corresponding machine readable source code which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange or
19. 085 35 085 36 085 37 085 38 085 39 085 40 085 41 0B5 42 0B5 43 0B5 44 03 Accumulative Usage Click and drag to zoom in FW roveresy AX OM Copyright 2015 Feeney Wireless All Rights Reserved Figure 11 Statistics Tab FW Skyus E User Manual Field Description Number of bytes sent during the current connection session with the cellular carrier WAN Bytes Sent o H eae f This is also referred to as the upload direction l Number of bytes received during the current connection session also referred to as WAN Bytes Received a PE the download direction LAN Bytes Sent Number of bytes sent from the Skyus E LAN Ethernet interface LAN Bytes Received Number of bytes received on the Skyus E LAN Ethernet interface The Bandwidth Usage chart provides an extremely useful visualization of data usage View Bandwidth Usage and bandwidth trends over a selectable period You can select the last 15 minutes For Previous last hour last day last 7 days and the last 30 days By clicking the various names of the values reported the chart can be changed to report only specific items of interest System This tab provides hardware and component information o x FW Skyus E Adminstration xy C ft 192 168 66 1 Socket Activity CARRIER 4G LTE Logging Activity Status Fe Dashboard Cellular Statistics Configuration go gt System Temperature 30 rc Skyus Temperature 35 c inistra
20. ES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM DAMAGES OR OTHER LIABILITY WHETHER IN AN ACTION OF CONTRACT TORT OR OTHERWISE ARISING FROM OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE 56
21. F CONTRACT TORT OR OTHERWISE ARISING FROM OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE Linux Kernel Copyright Note NOTE This copyright does not cover user programs that use kernel services by normal system calls this is merely considered normal use of the kernel and does not fall under the heading of derived work Also note that the GPL below is copyrighted by the Free Software Foundation but the instance of code that it refers to the Linux kernel is copyrighted by me and others who actually wrote it Also note that the only valid version of the GPL as far as the kernel is concerned is this particular version of the license ie v2 not v2 2 or v3 x or whatever unless explicitly otherwise stated Linus Torvalds GNU GENERAL PUBLIC LICENSE Version 2 June 1991 Copyright C 1989 1991 Free Software Foundation Inc 51 Franklin Street Fifth Floor Boston MA 02110 1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document but changing it is not allowed Preamble When we speak of free software we are referring to freedom not price Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software and charge for this service if you wish that you receive source code or can get it if you want it that you can change the software or use pieces of it in new free programs and that you know you can d
22. FW Skyus E User Manual FCC Compliance This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communication FW does not guarantee that interference will not occur in a particular installation Operation is subject to the following conditions a This device may not cause harmful interference b This device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment If this equipment does cause harmful interference to radio or television reception which can be determined by tuning the equipment off and on the user is encouraged to try and correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the distance between the equipment and the receiver Connect the equipment to outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV
23. P Format NMEA TAIP Dataset Size Minimal Verbose EZE sama Figure 25 GPS Profile Dialog Box Enter the IP address or URL of the server Enter the port number Note Each GPS server profile must have a unique IP URL and Port combination If you attempt to enter the same IP and port for a second server the profile will be rejected If you wish to use the same server for two profiles specify a different port Set the reporting interval The default is 60 seconds Set the desired protocol either TCP or UDP Select which protocol you want GPS data sent in NMEA or TAIP Select whether you want minimal GPS data sent or all data available Verbose Click Submit 36 FW Skyus E User Manual Administration The Administration page provides the ability to manage users web client and setting profiles view firmware information and upload firmware files and view and set limits on data usage To access this page click Administration in the navigation panel Information is organized under three tabs User Settings and Firmware User This tab provides information on network users and provides the ability to add new users and set their access levels SIA FW Skyus E Adminstration xu 4 gt C A D 192 168 66 1 m U Socket Activity Logging Activity CARRIER 4G LTE Status Fe Settings Firmware ra Configuration gop a Administration SK admin admin Change Password Add New User System Logging i
24. Power Attach an AC DC or DC DC power supply to the connector labeled Power 9 36v mating connector Molex 43025 0400 on the back of the Skyus E Plug the other end of the adapter into the power source Contact FW for available power supply options The pin assignments of the power connector are shown below Refer to the power specifications for operating and maximum allowed voltage ranges Power 9 36v Ground GPO out 9 36V In IGS in Figure 6 Power Connector Pin Assignments Power LED When power is applied the Power LED on the front panel will flash green slowly until the boot process is complete During normal operation the Power LED will flash green quickly The following table describes the Power LED modes LED Mode Color Description Slow flashing System is booting Quick flashing Power is applied boot process is complete normal operation Solid RQ System is in a non recoverable unhealthy state Flashing Red Over under voltage or temperature condition Verifying the Connections Connection to the carrier should occur approximately 90 150 seconds after applying power Connection time will vary according to carrier network and signal strength The Activity LED lights up with activity The Signal Strength LED array indicates the strength of the signal being received The color of the LEDs depends on the connection type You can connect to the Skyus E Interface via a Web browser to obtain more information about the
25. RAM INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OpenSSL Cryptography and SSL TLS Toolkit License LICENSE ISSUES The OpenSSL toolkit stays under a dual license i e both the conditions of the OpenSSL License and the original SSLeay license apply to the toolkit See below for the actual license texts Actually both licenses are BSD style Open Source licenses In case of any license issues related to OpenSSL please contact openssl core openssl org OpenSSL License Copyright c 1998 2011 The OpenSSL Project All rights reserved Redistribution and use in source and binary forms with or without modification are permitted provided that the following conditions are met 1 Redistributions of source code must retain the above copyright notice this list of conditions and the following disclaimer 52 FW Skyus E User Manual 2 Redistributions in binary form must reproduce the above copyright notice this list of conditions and the following disclaimer in the documentation and or other materials provided with the distribution 3 All advertising materials mentioning features or use of this software must display the following acknowledgment This product includes software developed by the OpenSSL Project for use in the
26. RIER 4G LTE Status FA APN GPO IGS Crossroads Connection GPS Configuration SOB DHCP LAN p LAN Settings aa a qa Administration WN LAN IP Address 192 168 66 1 i LAN Netmask 255 255 255 0 System Logging kz LAN Broadcast 192 168 66 255 Alerts 0 Notifications 7 ai 5 27 2015 2 44 40 PM Enable DHCP ED QOS has been 10 or less for 2 DHCP MTU 1500 bytes minutes i DHCP Lease 7200 seconds 5 27 2015 2 45 20 PM prape ohooh QOS has been 10 or less for 2 Ha minutes a 5 27 2015 2 46 00 PM DHCP Address Range 192 168 NG 2 QOS has been 10 or less for 2 192 168 66 254 minutes DHCP Router 192 168 66 1 DHCP Netmask 255 255 255 0 DHCP Subnet 192 168 66 0 DHCP Broadcast 192 168 66 255 FW Powered by P Copyright 2015 Feeney Wireless All Rights Reserved Figure 13 Network Tab Field Description DHCP DHCP LAN Drop down list to select between DHCP LAN settings Firewall rules Port Forwarding rules or Routing Rules Switch to enable or disable Dynamic Host Configuration Protocol DHCP DHCP is enabled by default DHCP Router Current router IP address Enable DHCP FW Skyus E User Manual Field Description LAN Settings LAN Address Current LAN IP address LAN Netmask Current LAN netmask LAN Broadcast Current LAN broadcast Firewall See Creating Firewall Rules Add Firewall Rule Opens a
27. Skyus E Whether your Skyus E is shipped with a Skyus cellular modem installed or you are installing an existing Skyus modem in the Skyus E appliance these instructions assume that the Skyus modem is already activated and provisioned Installation Summary e Inspect the package contents and compare against the packing list e Optional Install your existing Skyus modem in the unit if necessary e Install the Skyus E mounting plate and mount the unit to the plate e Connect the antennas e Connect the Skyus E to the LAN or desired device using the an Ethernet cable e Connect power e Verify the WAN connection e Verify the LAN connection e Recommended Change the default password Package Contents Package contents depend on the configuration ordered Compare the contents with the packing list If any items are missing or damaged contact FW support Item Type Description Skyus E Included Skyus E loT Appliance Power supply options include AC DC DC DC bare wire or auto accessory Power Supply Included plug commercial or industrial temperature Mounting Plate Skyus E mounting plate Antenna s FW offers several antennas that meet the Skyus E antenna specifications Ethernet 5 Ethernet cable RJ 45 to RJ 45 Skyus Cellular Modem included in many Skyus E configurations see the Skyus Modul A eae aad Skyus Specification Sheet or the Skyus DS Specification Sheet for models FW Skyus E User Manual Hardware Installation Perfo
28. address such as 192 168 66 100 e An IP address noting a specific network and corresponding subnet mask To utilize this method the syntax to use is IP address subnet mask For example to create a rule matching all traffic to an IP range of 192 168 66 X you can enter 192 168 66 0 255 255 255 0 in the From or To field 24 Skyus E User Manual e AnIPand slash notation subnet To take the same example as above to match all traffic to or from 192 168 66 X you may enter 192 168 66 0 24 Slash notation is a convenient shorthand to enter a subnet mask and is based on the decimal equivalent of the number of 1 s in the subnet mask For commonly used subnet masks 255 255 255 0 equals 24 255 255 0 0 equals 16 and 255 0 0 0 equals 8 e AURL such as www feeneywireless com If a URL is entered a DNS lookup will be performed and the appropriate rules will be created that match all IPs returned from DNS for that URL Note that for large sites such as www google com that employ load balancing this might not effectively block all traffic due to the dynamic nature of IPs that may be in use at any point in time e The special value of any This is the default and matches all traffic to any IP address Enter a specific desired TCP UDP or TCP amp UDP port as defined in the next step The port can also be left as the default of any to match all ports for the IP or URL defined in step 4 The port should be entered in the field to the right of the IP a
29. all with no notification given to the sending server or host In most cases this is the recommended method for denying specific IP traffic as it provides no information to a potential attacker that could be useful in mapping any existing firewall rules e Traffic matching a reject rule will be dropped by the firewall and the server or host sending the IP traffic will receive an ICMP Port Unreachable message A reject rule can be useful to alert the sender of the traffic that a firewall is present and configured to block specific types of traffic By default all traffic is allowed outbound from hosts on the Skyus E LAN to servers Inbound traffic from the Internet to hosts and devices behind the Skyus E on its LAN will not be routed to devices or hosts on the Skyus E LAN unless an appropriate Port Forwarding rule is created see Creating Port Forwarding Rules Creating a Port Forwarding rule to an internal host or device will automatically create the corresponding Firewall allow rule on the defined IP port and protocol In some cases it may be desired to create an additional Firewall rule to restrict the list of IP addresses or ranges of IP addresses the Port Forwarding rule applies to In this case create the appropriate accept deny and reject rules as desired to complement the automatically generated accept rule on the port and protocol EXAMPLE A specific example would be the creation of a rule to allow Port Forwarding to an IP camera to
30. allow remote viewing of video where additional Firewall rules are desired to only allow access to the camera from trusted IPs representing a trusted customer network In the Dir field choose either in or out to match the traffic direction the rule should be evaluated against e Choosing in will match IP traffic coming originating from hosts and servers on the Internet or Private Network Creating an in direction rule is useful to restrict access to specific devices or hosts located on the Skyus E LAN coming from the Internet The camera example in the previous note is a use case for an in rule e Choosing out will match IP traffic coming from a host or device located on the Skyus E LAN such as a laptop or router connected to the Skyus E Ethernet port An out rule can be used to allow deny or reject IP traffic going to servers on the Internet EXAMPLE It may be desired to block Web browsing to www webpage com or an IP address such as 20 30 240 50 To do this a direction of out should be selected in this step In the field noted as either From for an in direction rule or To for an out direction rule as defined in step 3 you can enter either a URL or an IP address This field defines the IP address or a number of IP addresses when a URL is entered to which the rule applies In this field you may enter information in one of multiple formats To create a rule matching all IP addresses leave the default of any in this field e Asingle IP
31. alue reported is the RSSI Received Signal Strength Indicator This value is useful when troubleshooting coverage or connection reliability and performance issues WAN IP address of the Skyus E when connected to a cellular data network Internet Protocol version 6 IPv6 address of the Skyus E if applicable Modem Resets Number of times the modem has reset since the Skyus E was last powered on Statistics This tab displays information about the amount of data sent and received over the WAN and LAN It allows you to view bandwidth usage over a specified range FW Skyus E Adminstration x C ft 5 192 168 66 1 Socket Activity Logging Activity CARRIER 4G LTE Status Fe Dashboard Cellular System Configuration fod WAN Bytes Sent 490905 WAN Bytes Received 1363964 Administration AN LAN Bytes Sent 1951653 p a LAN Bytes Received 639192 System Logging f View Bandwidth Usage For Alerts 0 Notifications 6 Previous 15 Mins Y ri Bandwidth Usage Click and drag to zoom in 5 27 2015 2 44 00 PM Qos has been 10 or less for 2 700000 Bytes minutes 600000 Bytes W 5 27 2015 2 44 40 PM a QOS has been 10 or less for 2 500000 Bytes minutes MAYON HANE IB Total Upload Download W 5 27 2015 2 45 20 PM 300000 Bytes WI Download QOS has been 10 or less for 2 H Upload minutes 200000 Bytes 100000 Bytes 0 Bytes 15 30 0B5 31 085 32 085 33 085 34
32. arks of Feeney Wireless LLC VaraSight and the VaraSight logo are trademarks of Feeney Wireless LLC Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products Intended Use Use this product only for the purpose it was designed for refer to the datasheet and user documentation For the latest product information visit us online at www feeneywireless com Open Source Software This product contains software distributed under one or more open source licenses including GNU General Public License Version 2 NetBSD Foundation License and PSF License Agreement for Python 3 1 1 For more information on this software including licensing terms and your rights to access source code see Appendix D Open Source Software Licenses or contact Feeney Wireless at www feeneywireless com Document Number 25 52 002 10 Revision B FW Skyus E User Manual Contents NENG Na AA AA AA AA AA NAA AA 4 Intended AUCIONCE ccsssesssssesessessecscssssssscsessscscsscsecsscucsecsecscsecsescsecussscsscuecscsecsecucsecsecucsscsecscsucsecsesscsecscsucsecseaecuccucsscsesucasesecucaeesecucsecseeneeseseeneeees 4 HCODE am APA APA AA ANAN NA EA AG 4 SFO UN NO Sesser AA T AND NABA NATN ANA AN NAA AA AA 5 BOTA AA PN 6 Tas 61 elo AA A IAE earner errata erm oven ern eset er eee 7 AVS AUN AUIS AA iiaa E EERE N E NR EE 7 GO AA 7 PVA UV eA CAFTA ne teases teen ete 8 Installing the Moun
33. attempting to activate a Skyus with a cellular carrier Unique identification number of the SIM inserted into the Skyus also referred to as an ICCID This identifier is often needed when activating a Skyus with your cellular provider Current Access Point Name APN in use by the network connection Values Up Down Reports whether or not a connection to the cellular carrier is up or down The connection is reported as up if an IP address has been assigned and a ping ICMP check to a URL or IP as configured under Network gt Connection gt Ping URL or Alt Ping URL is successful Connection Type Type of cellular connection such as 4G LTE and others Connection State 17 FW Skyus E User Manual Description Signal quality in dB Quality of Service QoS is a measure of the quality of the cellular signal as compared to interference and noise Optimal values vary dependent on cellular network type but generally a value consistently less negative than 10 dB indicates a lack of excessive noise or interference The QoS value can be useful to refer to when troubleshooting connection reliability issues packet loss or low bandwidth When QoS is consistently poor the value is displayed in red QoS Quality Of Service Strength of the cellular network signal in dBm When connected to an LTE network the value reported is the RSRP Reference Signal Received Power and when Signal Strength connected to any other network type the v
34. code cannot be changed i e this code cannot simply be copied and put under another distribution license including the GNU Public License zlib General Purpose Compression Library Version 1 2 8 License zlib h interface of the zlib general purpose compression library version 1 2 8 April 28th 2013 Copyright C 1995 2013 Jean loup Gailly and Mark Adler This software is provided as is without any express or implied warranty In no event will the authors be held liable for any damages arising from the use of this software Permission is granted to anyone to use this software for any purpose including commercial applications and to alter it and redistribute it freely subject to the following restrictions 1 The origin of this software must not be misrepresented you must not claim that you wrote the original software If you use this software in a product an acknowledgment in the product documentation would be appreciated but is not required 2 Altered source versions must be plainly marked as such and must not be misrepresented as being the original software 3 This notice may not be removed or altered from any source distribution Jean loup Gailly Mark Adler jloup gzip org madler alumni caltech edu JsonCPP C Library License The JsonCpp library s source code including accompanying documentation tests and demonstration applications are licensed under the following conditions The author Baptiste Lepilleur explicitly di
35. ddress or URL In this step it is possible to define a specific port to match in the Firewall rule It may be valuable to refer to online information noting commonly used ports for various services FW has provided a convenient commonly used services option at the top of the firewall entry dialog box The appropriate syntax in this step is either a specific numeric port ranging from 1 to 65535 or the default of any to match all ports To create rules matching a range of ports it is necessary to create multiple firewall rules Commas or non numeric characters other than any should not be used in this field Enter the IP protocol to match the Firewall rule against The allowed options are the default of tcp udp or only tcp or udp NOTE Generally users can safely leave this at the default of tcp udp to match the rule against either protocol 25 FW Skyus E User Manual Creating Port Forwarding Rules The Skyus E supports Port Forwarding functionality Port Forwarding is designed to allow inbound IP traffic to be routed to a host or device on the Skyus E LAN The use of Port Forwarding is closely related to the creation of appropriate Firewall rules Refer to Creating Firewall Rules for more detail related to the creation of Firewall rules to restrict the allowed hosts which can access an attached device via the use of Port Forwarding rules Status APN GPO IGS Crossroads Connection Configuration fob Port Forwatling Admin
36. dialog to create a firewall rule Common Services HTTP HTTPS FTP Telnet SSH DNS Selecting a service automatically places values in the From Port and Protocol fields Logging Checkbox to enable logging Number Firewall rule number This is the position in the rule list where the new rule is to be placed Rules at the top of the list are evaluated first By default new rules are automatically given a number that puts the new rule at the bottom of the list but this can be changed by the user Rule allow deny reject Dir direction in out From any or a specific port number Protocol tcp upd tcp upd Add Port Forward Rule Opens a dialog to create a port forwarding rule Number Name Any name Outer Port Inner Port IP Address Desired LAN IP address to forward traffic to Protocol tcp upd tcp upd Routing See Creating Routing Rules Add Routing Rule Opens a dialog to create a static routing rule e Destination Network e Subnet Subnet e Gateway IP on the Skyus E LAN to route through 22 FW Skyus E User Manual Creating Firewall Rules The Skyus E supports the creation of firewall rules to either block or allow certain types of IP traffic Firewall rules can be configured to Allow Deny or Reject IP traffic to or from specific servers IPs or groups of IPs You can optionally choose to filter IP traffic based on specific ports and protocols Status ko APN GPO IGS Crossroads Connection Con
37. e Qu ssssscsssecsssecsssscsssscessscsssecssscssscesscsesessssesscsesscsesscsesscsesscsesscsesacsessceeesees 52 CEN Se SS pA NANA AA AA AA neste acetate ee cee eee eee ce eee eee eee 52 Open a a NS a APAN AANGAT GN GNG AA ARA G 52 Orginal S5LEAY License eusir anaE E ETE E EA EA E E 53 zlib General Purpose Compression Library Version 1 2 8 LiCenSe ss ssseessseessseessseesssseossseessseossseosseeosseessseeosseossseosseeosseeosseeosseee 54 JsonCPP CHF Library HAAAY 54 WEeD50cket 4 Version O D I AGA KAKANAN NANANA EEEE Ea aa 55 Boost Software License Version 1 0 August 17th 2003 seseessseessseessseessseessseessseeessecosseesssecossereuseeesseesseeesseeosseeesseeesseeesseeesseeesseee 55 rapidjson Parser Generator for C LICENSE cccccssessssessssessccessssesscsesscsesscscsscsesscsessesesnesssessesessssecessecsssecaesucsesseacsucaesseaesucacseaeseaeeaeers 56 FW Skyus E User Manual Overview The Skyus E loT Appliance simplifies the effort of implementing wireless connectivity in Internet of Things loT networks Built on FW s proven Skyus cellular modem technology the Skyus E provides a standard Ethernet interface for easy connection to customer devices The Skyus E s rugged compact aluminum body and its ease of installation make it perfect for deployment in a wide variety of loT applications including kiosks digital signage ATMs and many others Powered by FW s own Linux implementation Axiom the Skyus E i
38. e source code from the same place counts as distribution of the source code even though third parties are not compelled to copy the source along with the object code 4 You may not copy modify sublicense or distribute the Program except as expressly provided under this License Any attempt otherwise to copy modify sublicense or distribute the Program is void and will automatically terminate your rights under this License However parties who have received copies or rights from you under this License will not have their licenses terminated so long as such parties remain in full compliance 5 You are not required to accept this License since you have not signed it However nothing else grants you permission to modify or distribute the Program or its derivative works These actions are prohibited by law if you do not accept this License Therefore by modifying or distributing the Program or any work based on the Program you indicate your acceptance of this License to do so and all its terms and conditions for copying distributing or modifying the Program or works based on it 6 Each time you redistribute the Program or any work based on the Program the recipient automatically receives a license from the original licensor to copy distribute or modify the Program subject to these terms and conditions You may not impose any further restrictions on the recipients exercise of the rights granted herein You are not responsible for enforci
39. ent optimal solutions in these types of projects To configure Port Forwarding rules follow the steps below 1 Click Add Port Forwarding Rule The Port Forward dialog box opens 26 Skyus E User Manual Port Forward Name Outer Port Inner Port IP Address Protocol Save Cancel Figure 17 Port Forward Dialog Box Choose a name for the Port Forwarding rule to identify it It is recommended that you choose a name that describes the application the rule is enabling such as Camera Web Access The name of the rule has no effect on the rule itself Enter the TCP or UDP port number you will use to access the device remotely into the Outer Port field The Outer Port refers to the port the Skyus E will forward from its cellular WAN interface to an attached host or device connected to its LAN Ethernet port Valid ports are numeric values ranging from 1 to 65535 only and should not include any non numeric digits such as a comma Enter the TCP or UDP port the traffic will be routed to on the attached host or device in the Inner Port field If the Inner Port entered differs from the Outer Port the Skyus E will perform Port Translation as well as Port Forwarding Port Translation is designed to support the use of a different external port number that can be used to access devices that may not support changing the TCP or UDP port the desired service or application they support listens on Use Cases There are several com
40. entifier MAC Address er and thus can be useful when creating MAC address filtering rules 15 FW Skyus E User Manual Description Signal quality in dB Quality of Service QoS is a measure of the quality of the cellular signal as compared to interference and noise Optimal values vary dependent on cellular network type but generally a value consistently less negative than 10 dB QoS Quality of Service atas l indicates a lack of excessive noise or interference The QoS value can be useful to refer to when troubleshooting connection reliability issues packet loss or low bandwidth When QoS is consistently poor the value is displayed in red Unique identification number of the SIM inserted into the Skyus also referred to as an ICCID This identifier is often needed when activating a Skyus with your cellular provider Temperature of the Skyus radio module within the Skyus in degrees Celsius Strength of the cellular network signal in dBm When connected to an LTE network the value reported is the RSRP Reference Signal Received Power and when Signal Strength connected to any other network type the value reported is the RSSI Received Signal Strength Indicator This value is useful when troubleshooting coverage or connection reliability and performance issues UpTime Total time the Skyus E has been powered up since the last power cycle or reboot Voltage in mV millivolts detected at the Skyus E power jack The Skyus E can
41. figuration fo Firewall z Administration ESS From Direction Protocol To f w any in tcp any O Modify x Delete System Logging VP O Add Firewall Rule Figure 14 Firewall Rules 1 Click Add Firewall Rule The Firewall dialog box opens Firewall Common Services select Logging Number Rule Dir From Protocol Save Cancel Figure 15 Firewall Dialog Box Selecting a value in the Common Services field HTTP HTTPS FTP Telnet SSH or DNS automatically selects values for the From Port and Protocol fields You can choose to include this firewall rule in system logging by checking the Logging box 2 When adding or modifying a firewall rule first define the position on the list of firewall rules in which the new rule should be evaluated Do this by modifying the value in the Number field By default each new rule will be placed at the bottom of the list Rules at the top of the list take priority over rules at the bottom This is important and useful if for example you want to create a set of firewall rules to accept specific IP traffic and reject all other IP traffic The rules to accept the traffic should be at the top of the list 3 Next in the Rule field choose whether to allow deny or reject the IP traffic that matches the rule criteria 23 Skyus E User Manual e Traffic matching an allow rule will be routed to the appropriate host or server e Traffic matching a deny rule will be silently dropped by the firew
42. ftware in whole or in part and all derivative works of the Software unless such copies or derivative works are solely in the form of machine executable object code generated by a source language processor THE SOFTWARE IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE TITLE AND NON INFRINGEMENT IN NO EVENT SHALL THE COPYRIGHT HOLDERS OR ANYONE DISTRIBUTING THE SOFTWARE BE LIABLE FOR ANY DAMAGES OR OTHER LIABILITY WHETHER IN CONTRACT TORT OR OTHERWISE ARISING FROM OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE 55 FW Skyus E User Manual rapidjson Parser Generator for C License Copyright C 2011 Milo Yip Permission is hereby granted free of charge to any person obtaining a copy of this software and associated documentation files the Software to deal in the Software without restriction including without limitation the rights to use copy modify merge publish distribute sublicense and or sell copies of the Software and to permit persons to whom the Software is furnished to do so subject to the following conditions The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software THE SOFTWARE IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE WARRANTI
43. ging Activity State Connection IMEI Up 4G LTE 359225050540152 10 60 95 176 To ba 8c 9b 99 ca 81 dBm 11 dB SIM 89014103277188507037 Temperature 30 C Up Time 0 Hours 20 Min 55 Sec Voltage 14600 mV Powered by ax m PW Copyright 2015 Feeney Wireless All Rights Reserved Figure 7 Skyus E Web Interface Login Screen Enter the default username and password and click the Log in icon The default username and password are Username admin Password fwxxxxxx Where xxxxxx is the last six characters of the MAC address excluding separators It is recommended that you change the default password The password can be changed on the Administration 5 User tab To log out click the Log out icon on any page The Skyus E Interface will automatically log out after about 10 minutes of inactivity Remote Access to the Skyus E Interface The Skyus E Interface can also be accessed remotely if your Skyus has been assigned a publicly routable IP address from your cellular carrier To access the Skyus E remotely the default port is 8080 Access the Skyus E using the following URL http lt IP assigned from your carrier gt 8080 Note The same user cannot be logged in on multiple devices If your application requires multiple users to manage the Skyus E you can add and manage users on the User tab see User 13 FW Skyus E User Manual Skyus E Banner After logging in to the Skyus E I
44. he cable clip 5 into place over the antenna connectors 46 Skyus E User Manual Slide the Skyus module into the modem compartment carefully tucking in the cables so that they do not extend beyond the opening of the Skyus E enclosure and do not catch on the front edge of the PCB The Skyus fits snugly in the compartment so be sure to apply firm pressure Replace the faceplate 47 FW Skyus E User Manual Appendix D Open Source Software Licenses The MIT License MIT Copyright 2015 Feeney Wireless LLC Permission is hereby granted free of charge to any person obtaining a copy of this software and associated documentation files the Software to deal in the Software without restriction including without limitation the rights to use copy modify merge publish distribute sublicense and or sell copies of the Software and to permit persons to whom the Software is furnished to do so subject to the following conditions The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software For open source software components the following applies THE SOFTWARE IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM DAMAGES OR OTHER LIABILITY WHETHER IN AN ACTION O
45. her the web interface or reset button Update Applies the current Skyus E settings to the selected profile Exports the current profile Save Current Settings Creates a new profile based on the current Skyus E settings Restore Factory Defaults Restores the Skyus E to factory settings You will be prompted to confirm the restore Opens a dialog to select a settings file to upload The dialog allows you to name the Upload Settings profile and browse to the file to upload Firmware This tab displays the current software and firmware versions installed on the Skyus E and provides the ability to upload Skyus E firmware upgrades FW Skyus E Adminstration xi i amp C A N 192 168 66 1 Socket Activity CARRIER 4G LTE ngaba Status User Settings Configuration Versions Administration Device Version SW1000 A01 f System Log gin g m Software Version SWA9000 REV A01 0 26 May 2015 Alerts 0 Notifications 13 Firmware Version a SWI9X1 5C 05 05 16 02 r21040 carmd fwbuild1 W 5 27 2015 2 48 40 PM System Name D ra g amp D ro p a Fi e Qos has been 10 or less for 2 SkyusE armhf tar gz minutes or click to browse files W 5 27 2015 2 49 25 PM QOS has been 10 or less for 2 minutes 5 27 2015 2 50 01 PM QOS has been 10 or less for 2 minutes FW roveresy AXIOM Copyright 2015 Feeney Wireless All Rights Reserved Figure 28 Firmware Tab FW Skyus E User Ma
46. imer in the documentation and or other materials provided with the distribution 53 FW Skyus E User Manual 3 All advertising materials mentioning features or use of this software must display the following acknowledgement This product includes cryptographic software written by Eric Young eay cryptsoft com The word cryptographic can be left out if the routines from the library being used are not cryptographic related 4 Ifyou include any Windows specific code or a derivative thereof from the apps directory application code you must include an acknowledgement This product includes software written by Tim Hudson tjh cryptsoft com THIS SOFTWARE IS PROVIDED BY ERIC YOUNG AS IS AND ANY EXPRESS OR IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT INDIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES LOSS OF USE DATA OR PROFITS OR BUSINESS INTERRUPTION HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY WHETHER IN CONTRACT STRICT LIABILITY OR TORT INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE The licence and distribution terms for any publically available version or derivative of this
47. is tab provides GPS information and allows you to identify up to four servers to which GPS data is to be sent FW Skyus E Adminstration xy 1 C ft 5 192 168 66 1 Socket Activity Logging Activity CARRIER 4G LTE Status fe Network APN GPO IGS Crossroads Connection Configuration SOB Live Data Satellites 5 88 8 B Administration R Latitude 44 02 39 N Longitude 123 11 1 W Altitude 227 359450 System Logging R Speed 0 000000 moh Direction 219 9 W 5 27 2015 2 47 20 PM General Settings QOS has been 10 or less for 2 minutes Device ID 1234 W 5 27 2015 2 48 00 PM QOS has been 10 or less for 2 minutes Alerts 0 Notifications 11 QOS has been 10 or less for 2 minutes W 5 27 2015 2 48 40 PM Server Settings Server 1 add Server 2 add PW Copyright 2015 Feeney Wireless All Rights Reserved Figure 24 GPS Tab Field ba General General Settings Provides a field for Provides a field for setting the GPS Device ID the GPS Device ID Allows you to specify the settings of up to four servers to which GPS data can be Server Settings Na transmitted If no servers are specified GPS data is sent only to the Crossroads server To add a GPS server 1 Click the Add icon 9 The GPS Profile dialog box opens O et R Skyus E User Manual GPS Profile Server 1 E9 IPJURL Port Reporting Interval 60 mare Protocol TCP UD
48. istration Name Outer Port Inner Port P p Add Port Forward Rule System Logging Figure 16 Port Forwarding Rules Typical applications of Port Forwarding include e Remote viewing of video from a webcam camera connected to the Skyus E Ethernet port Remote management of devices such as PCs or routers connected to the Skyus E Ethernet port To make use of Port Forwarding in most cases a publically routable static IP address may be necessary or desirable In these cases you may wish to engage FW Support for assistance or work directly with your chosen cellular carrier to assign a publicly routable static IP address Public Static IP addresses are available from Verizon Sprint and AT amp T but are generally not the default option for data devices such as the Skyus A publicly routable static IP address is one in which the IP address assigned when the Skyus connects to the carrier network is unchanging and does not block or restrict most traffic from any other Internet address In some use cases where maximum security is required the use of Private Networking or Restricted Static Addresses can also provide an unchanging IP address to the Skyus to support Port Forwarding This provides the added benefit of additional security through restrictions on what other networks or Internet IP addresses can communicate with the Skyus FW field engineering staff offer consulting services to help our customers best identify and implem
49. kyus E Adminstration x Vie C f O 192 168 66 1 U Socket Activity Logging Activity CARRIER 4G LTE Status Network APN GPO IGS Crossroads GPS 7 Configuration a TH k3 pu o CV Connection O 2 Ping URL www feeneywireless com Administration ie s 2 7 Ping URL alt www yahoo com System Logging kz Ping Interval 7 S Ping Retry Attempts Alerts 0 Notifications 11 g y P Ping Retry Interval ue Ka 5 27 2015 2 47 20 PM 3G RSSI re p 120 dBm QOS has been 10 or less for 2 minutes 4G RSSI H H 120 dBm 5 27 2015 2 48 00 PM QOS has been 10 or less for 2 minutes 5 27 2015 2 48 40 PM QOS has been 10 or less for 2 minutes AV roveretty AXIOM Copyright 2015 Feeney Wireless All Rights Reserved Field Description URL of the primary ping address The Ping URL and Alt Ping URL values are used by the Skyus E to test at the defined Ping Interval if the Skyus E remains online and can Ping URL ping the URLs defined If the pings fail to both the Ping URL and Alt Ping URL for the number of Ping Retries defined then the Skyus E will reset the Skyus modem and attempt to reconnect 3G RSSI Slider to set the minimum Receive Signal Strength Indicator RSSI for 3G connections Range 125 dB to 90 cB 4G RSSI Slider to set the minimum RSSI for 4G connections Range 128 dB to 90 dB FW Skyus E User Manual GPS Th
50. le GPO Skyus E will ground the GPO line This output is of the open drain type The GPO is accessed on pin 4 of the Skyus E power connector see Figure 6 Ignition Sense Button to enable or disable IGS on the power connector for use in vehicle or battery Enable Ignition Sense at powered applications Sets the shutdown timer Range 0 999 seconds The Shutdown Timer value is the length of time in seconds that the Skyus E will remain powered up when ignition IGS Shutdown Timer sense is enabled after the ignition sense pin voltage drops below 9V This value in most automobile applications is the length of time the Skyus E will remain on after the vehicle ignition is turned off Sets the IGS mode Values e Disabled e Auto attempts to detect whether the Skyus E is being used in a vehicle with Voltage Shutdown Sense either a 12V or 24V battery and automatically configure typical low battery thresholds Normal shuts down the Skyus E when IGS is determined to be outside the designated range after the set shutdown time has passed 32 FW Skyus E User Manual Crossroads This tab provides the ability to enable connection of the Skyus E to Crossroads Crossroads is an Internet of Things loT application framework that can be used to monitor and manage your Skyus E units in the field remotely Contact your FW Support for more information or go to the Crossroads Home Page FW Skyus E Adminstration xi C ff M 192 168 66 1 Socket
51. low the camera to function as expected for remote viewing but the use of port translation does not require modifying the camera configuration settings for HTTP and HTTPS ports from their defaults making future maintenance of the Web camera easier e Consider a use case where multiple Web cameras are connected via an Ethernet switch to the Skyus E where all cameras have a default HTTP port of 80 TCP For example purposes assume three cameras are used with IP addresses on the Skyus E LAN network of 192 168 66 100 192 168 66 110 and 192 168 66 120 By creating three Port Forwarding rules using Port Translation it is possible to keep all three cameras configured to remain using TCP 80 for their HTTP Web interfaces To do this create a rule called Camera 1 with an Outer Port of 8080 TCP and inner port of 80 directed to 192 168 66 100 Create a Camera 2 rule with an outer port of 8081 TCP and inner port of 80 directed to 192 168 66 110 Lastly create a Camera 3 rule with an outer port of 8082 TCP and an inner port of 80 directed to 192 168 66 120 The result of these three rules would allow you to access all three cameras on TCP ports 8080 8081 and 8082 respectively via the Skyus E WAN interface assigned by your cellular carrier Select TCP amp UDP TCP or UDP for the protocol In most cases it is common to simply select the default of TCP amp UDP Enter the IP address of the device connected to the LAN interface of the Sky
52. mon use cases of Port Translation combined with Port Forwarding such as e Most cellular carriers block several of the most commonly used ports for HTTP TCP 80 HTTPS TCP 443 and SMTP TCP 25 This may affect certain applications such as the use of IP cameras or the Web interfaces of various devices In these scenarios the two available solutions are to either modify the configuration of the device to use a different port number or to utilize Port Translation as detailed above to translate to a port that is not blocked by the carriers to the default port of your device which would be blocked For example consider the use case of a Web camera with a Web interface configured as typical using the default HTTP and HTTPS ports of 80 TCP and 443 TCP These two ports are blocked in the inbound direction by all major US cellular carriers In this case there are two potential solutions You can either modify your camera configuration to use different ports such as 8080 TCP and 8443 TCP with a pair of basic Port Forwarding rules where both the Outer and Inner port in the rules created are 8080 and 8443 respectively or you could use Port Translation in combination with 2 7 Skyus E User Manual Port Forwarding and keep your camera configuration unchanged To accomplish this create a rule with 8080 TCP for the outer port and 80 TCP for the inner port as well as a second rule for 8443 TCP outer port and 443 TCP inner port Either solution will al
53. ng compliance by third parties to this License 7 f as a consequence of a court judgment or allegation of patent infringement or for any other reason not limited to patent issues conditions are imposed on you whether by court order agreement or otherwise that contradict the conditions of this License they do not excuse you from the conditions of this License If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations then as a consequence you may not distribute the Program at all For example if a patent license would not permit royalty free redistribution of the Program by all those who receive copies directly or indirectly through you then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program If any portion of this section is held invalid or unenforceable under any particular circumstance the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices Many people have made generous contributions to the wide range of software distributed through that system
54. ng with the Program You may charge a fee for the physical act of transferring a copy and you may at your option offer warranty protection in exchange for a fee 2 You may modify your copy or copies of the Program or any portion of it thus forming a work based on the Program and copy and distribute such modifications or work under the terms of Section 1 above provided that you also meet all of these conditions a You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change 49 FW Skyus E User Manual b You must cause any work that you distribute or publish that in whole or in part contains or is derived from the Program or any part thereof to be licensed as a whole at no charge to all third parties under the terms of this License c If the modified program normally reads commands interactively when run you must cause it when started running for such interactive use in the most ordinary way to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty or else saying that you provide a warranty and that users may redistribute the program under these conditions and telling the user how to view a copy of this License Exception if the Program itself is interactive but does not normally print such an announcement your work based on the Program is not required to print an announcement These requirements apply to
55. nterface the banner will display connection information including the signal type signal strength and activity as shown below Signal Signal Web Strength Type Activity O Socket Activity Logging Activity CARRIER 4G LTE Logging Figure 8 Skyus E Interface Banner e Signal Strength This indicator matches the Signal Strength LEDs on the Skyus E The number of bars indicates signal strength and the color indicates data usage e Signal Type This is the name of the cellular carrier to which the Skyus E is connected e Socket Activity This indicator flashes with connection activity to the Skyus E e Logging Activity This indicator will be lit if the logging function of the Skyus E has been turned on Status The Status page provides information about the Skyus E device connection status and statistics and the basic state of the system To access this page click Status in the navigation panel Information on this page is organized under four tabs Dashboard Cellular Statistics and System 14 FW Skyus E User Manual Dashboard This tab provides a summary of Skyus E status similar to the summary that appears on the login page It also displays any current alerts and notifications FW Skyus E Adminstration x gt C ff 5 192 168 66 1 Socket Activity Logging Activity CARRIER 4G LTE Status Cellular Statistics System Configuration Ee ini i SYET Administration IR System Logging
56. nual Field Description Versions Device Version Skyus E firmware version Software Version Skyus E processing module firmware version Firmware Version Skyus module firmware version System Name Host name Upload Drag and drop a tar gz file or click the upload area to browse to a file This will update Upload Area P the Skyus E firmware Firmware upgrade files are available from FW Support System Logging The Skyus E provides extensive system logging capabilities gt C ff 5 192 168 66 1 Socket Activity Logging Activity CARRIER 4G LTE Status Eie Enable Logging Configuration TH Log Level All v Event Type Any v Enable Debug Output Search se Fi 7 t tT gt M Administration SR naomi Event Type Leve essage No data available in table Showing 0 to 0 of 0 entries System Logging i Alerts 0 Notifications 14 Live Activity Clear Output Export Verbose pa 5 27 2015 2 49 25 PM QOS has been 10 or less for 2 minutes W 5 27 2015 2 50 01 PM QOS has been 10 or less for 2 minutes QOS has been 10 or less for 2 W 5 27 2015 2 50 46 PM minutes FW eaw AXIOM Copyright 2015 Feeney Wireless All Rights Reserved Figure 29 System Logging Field Description Enable Logging Click the button to turn logging on or off Log Level Select the log level All Info Warning Critical Debug AU FW Skyus E U
57. o the Skyus E Power LED is flashing red Power LED is solid red Power LED is flashing quickly and one or more of the following is true At least two minutes have passed since power was applied to the Skyus E allowing time for the cellular connection to be made No other LEDs are lit No Modem Detected is displayed in the interface banner Connection State Down Connection Type None QoS no value Alert Connect was dropped or lost Remedy Check the power source and connections This indicates an over or under voltage condition or an over or under temperature condition Remove power from the device and allow the unit to cool if the Skyus Temperature value was high or the unit is being operated in hot ambient conditions Reapply power This indicates a non recoverable unhealthy state Contact FW customer support These symptoms all point to a problem with the Skyus module inside the Skyus E Open the front panel of the Skyus E as shown in Appendix C Swapping Modems If no Skyus module is installed install a module Ifa Skyus module is installed make sure the USB and antenna connectors are correctly and firmly attached If the connections are good try swapping out the Skyus module with a known working device If a connection can be made with a different Skyus module the SIM card inside the original may be missing installed incorrectly or damaged Contact FW customer su
58. o these things 48 FW Skyus E User Manual To protect your rights we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights These restrictions translate to certain responsibilities for you if you distribute copies of the software or if you modify it For example if you distribute copies of such a program whether gratis or for a fee you must give the recipients all the rights that you have You must make sure that they too receive or can get the source code And you must show them these terms so they know their rights We protect your rights with two steps 1 copyright the software and 2 offer you this license which gives you legal permission to copy distribute and or modify the software Also for each author s protection and ours we want to make certain that everyone understands that there is no warranty for this free software If the software is modified by someone else and passed on we want its recipients to know that what they have is not the original so that any problems introduced by others will not reflect on the original authors reputations Finally any free program is threatened constantly by software patents We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses in effect making the program proprietary To prevent this we have made it clear that any patent must be licensed for everyone s free use or not licensed
59. on Sheet or the Skyus DS Specification Sheet for modem specific information Skyus Global not supported Skyus 4G LTE embedded modem kit Verizon T Mobile AT amp T uses software Multi Carrier Support f switchable radio technology for multi carrier support Standards Approvals FCC Part 15 Class B GPS Skyus DS Models Only Satellite Channels Acquisition Time Hot Start 1 second Warm Start 29 seconds Cold Start 32 seconds Accuracy Horizontal lt 5m 90 Altitude lt 8m 90 Velocity lt 0 2 m s FW Skyus E User Manual Sensitivity Tracking 161 dBm Acquisition Assisted non LTE 158 dBm Acquisition Assisted LTE 153 dBm Acquisition Standalone 145 dBm Operational Limits Altitude lt 600m or Velocity lt 100 m s Either limit may be exceeded but not both Software TAST E AXIOM integrated connection management FW embedded Linux image enables P J gt Y rapid addition of functions features and carrier support Integrated onboard routing Network Address Translation NAT and firewall Security module Block Diagram 10 100 Ethernet LAN USB Data USB Data Processing System Skyus Primary Antenna Maal habla Maila da D Secondary Antenna DS GPS Antenna 2 SIM Grounding Skyus E pa Regulation DC Input Figure 2 Skyus E Block Diagram FW Skyus E User Manual Installation The following sections describe the installation and initialization of the
60. operate normally between 9 36V DC which is equivalent to 9000 to 36000 mV DC Note that Voltage in vehicle environments the Skyus E can be configured to shut down at voltages above the 9V minimum operating voltage threshold to protect the health of the vehicle battery 16 FW Skyus E User Manual Cellular This tab provides information about your cellular carrier and connection status FW Skyus E Adminstration xy amp C 2 D 192 168 66 1 Socket Activity Logging Activity CARRIER 4G LTE Status Fe Dashboard Statistics System Configuration god Carrier Carrier Name Phone Number 14582054899 a s B Administration EN IMEI 3592250505401 52 X SIM 89014103277188507037 System Logging i2 APN Broadband Alerts nd Notifications 5 nna hate Up x W 5 27 2015 2 43 20 PM EO HA kataba QOS has been 10 or less for 2 QoS 12 dB minutes Signal Strength 78 dBm QOS has been 10 or less for 2 minutes IPv6 fe80 8cb 3cff fe3b 108 eth1 Modem Resets 0 W 5 27 2015 2 44 40 PM QOS has been 10 or less for 2 minutes FW oeiy AXIOM Copyright 2015 Feeney Wireless All Rights Reserved Figure 10 Cellular Tab Field Description Name of the cellular carrier in use such as AT amp T Sprint T Mobile Verizon etc Phone Number Phone number programmed into the device associated with the carrier account IMEI number of the Skyus radio module The IMEI is often required when
61. orms two different reset functions The type of reset performed depends on how long the button is held down When the button is pressed and held down the signal strength LEDs will flash specific colors three times to indicate the type of reset that will be performed when the button is released CAUTION Do not remove power to the Skyus E or disconnect interface cables during a reset Wait until the device is fully reset and the connection has been reestablished Failure to wait might compromise the device NOTE The reset button is functional only when the Activity LED is lit Pressing the reset button will have no effect when the Activity LED is not lit To press the button use a narrow tool such as a precision screwdriver or the end of a paperclip Reset Type Button Press LEDFlashColor Description Resets the system using the current settings This is Soft 5 seconds Green a similar to removing and reapplying power to the Skyus E Factory Default 10 seconds Red Resets the system to the as shipped settings Approximate duration of press t Does not reset firmware to factory settings Any after purchase firmware upgrades will remain intact After a reset restart your browser to reload the Skyus E Interface and ensure that the latest settings are displayed 11 FW Skyus E User Manual Skyus E Administration Interface The Skyus E Administration Interface is an all purpose administrative tool that provides an intuitive Web inte
62. other router or gateway on the Skyus E LAN subnet Status Ho APN GPO IGS Crossroads Connection Configuration TH aika 7 Administration G y S Destination Subnet Gateway Add Routing Rule 2 System Logging 2 Figure 18 Routing Rules To create a routing rule 1 Click Add Routing Rule The Routing dialog box opens Routing Destination Subnet Gateway Figure 19 Routing Dialog Box 2 Enter addresses for the Destination Subnet and Gateway EXAMPLE If another router is connected to the Skyus E Ethernet port and assigned an IP address of 192 168 66 100 and this second router has other subnets such as 192 168 1 0 24 then creating a static route to 192 168 1 0 24 pointing to 192 168 66 100 will allow other hosts on the Skyus E LAN to reach the 192 168 1 0 24 network via this second router 29 FW Skyus E User Manual APN This tab provides the ability to create custom Access Point Name APN profiles and set the current profile The default APN will be assigned by your cellular carrier The APN defines which networks and IP addressing are assigned by your cellular carrier Most carriers provide several default APN options for private IP addressing public IP addressing public static IP addressing customer custom IP addressing private networking VPNs and or restricted static IP addressing For more information regarding APNs contact your FW representative FW Skyus E Adminstration xy 1
63. pport 43 Signal strength drops to no bars Other symptoms might include e Connection Type degrades for example to 2G e Signal Strength drops to a large negative value for example 128 dBm Antenna s are connected but signal strength is still low After selecting an APN profile other than the Default on the Configuration 5 APN screen Cellular connection is lost The Power LED flashes green The Skyus E Interface becomes inaccessible After selecting Enable Ignition Sense on the Configuration 5 GPO IGS screen and clicking Save e Cellular connection is lost e The Power LED goes to solid green Skyus E User Manual Check antenna connections If using only one antenna make sure it is connected to the SMA connector labeled Primary Check the internal antenna connections to the Skyus modem Open the front panel of the Skyus E as shown in Appendix C Swapping Modems Make sure both internal SMA antenna cables are connected to the Skyus The shorter cable labeled FW8163 A is the Primary antenna cable and should be attached to the outermost antenna connector on the Skyus module The longer cable labeled FW7837 A is the Secondary antenna cable and should be attached to the innermost antenna connector on the Skyus module This occurs when an invalid APN profile has been selected as the current APN profile Press and hold down the reset button until the Skyus E resets approximately five seconds The
64. published by the Free Software Foundation 10 If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different write to the author to ask for permission For software which is copyrighted by the Free Software Foundation write to the Free Software Foundation we sometimes make exceptions for this Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally NO WARRANTY 11 BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE THERE IS NO WARRANTY FOR THE PROGRAM TO THE EXTENT PERMITTED BY APPLICABLE LAW EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND OR OTHER PARTIES PROVIDE THE PROGRAM AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU SHOULD THE PROGRAM PROVE DEFECTIVE YOU ASSUME THE COST OF ALL NECESSARY SERVICING REPAIR OR CORRECTION 12 IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER OR ANY OTHER PARTY WHO MAY MODIFY AND OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE BE LIABLE TO YOU FOR DAMAGES INCLUDING ANY GENERAL SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROG
65. rface for monitoring configuring and managing the Skyus E From the interface you can check the status of your connections to the WAN and LAN view the status of the Skyus E hardware configure network and security settings add users set permission levels and create and view system logs among other activities Supported browsers are Chrome Opera and Firefox Use of Internet Explorer 10 or newer may result in less than optimal interface performance earlier versions of Internet Explorer have not been tested Note The screenshots depicted in the following sections are examples only The actual data displayed depends on the configuration and status of your Skyus E Skyus E Default Settings The following table provides the default system settings you will need to access the Skyus E Interface Parameter Default Setting Skyus E Local URL http 192 168 66 1 fWXXXXXX where xxxxxx is the last six digits of the MAC address not including dashes or colons shown on the utility login page Remote Port 8080 Password Logging In To log in to the Skyus E Interface open a browser on a computer connected to the Internet and type the Skyus E IP address into the address bar The interface login page displays as shown below A summary of the current status of the Skyus E appears on this page for quick reference 12 FW Skyus E User Manual A Wa gt C A D 192 168 66 1 FW Skyus E Adminstration Socket Activity Log
66. rm the hardware installation steps described in the following sections These instructions assume that your Skyus E was shipped with a Skyus modem pre installed e If you already have a Skyus modem and want to upgrade to the Skyus E contact FW Sales for the Skyus E Retrofit kit Complete the steps described in the Skyus E Retrofit Assembly Instructions before proceeding with the installation e If you want to replace the existing Skyus modem in your Skyus E follow the instructions in Appendix C Swapping Modems before proceeding with the installation Installing the Mounting Plate The Skyus E attaches easily to the mounting plate sold separately The figure below shows the dimensions and mounting hole locations of the plate The mounting hardware you use will depend on the requirements of your enclosure Countersunk bolts or screws may be used Appendix B Mounting Plate Template provides a full scale template you can print and use to mark the screw hole positions Note The mounting plate hole spacing supports mounting to a monitor or TV using VESA standard 75 mm hole spacing if the appropriate screws are used 74 93 mm 2 95 in 2413 mm 95 in 74 93 mm 2 95 in 12344 mm 4 86in 131 32 mm 5 17 in E 125 98 mm 4 96 in 25 15 mm 99 in Figure 3 Mounting Plate Dimensions Not to scale FW Skyus E User Manual The Skyus E is mounted to the plate by placing the front or back edge of the Skyus E over
67. s capable of supporting nearly any FW Skyus module With Axiom you get rapid connections integrated connection management and robust watchdog logic Skyus E features include e Operation on all major US carrier networks e 4G LTE support on all major US carriers e Modular design allows you to swap between Skyus carrier radio modules e Skyus DS model allows you to switch carriers without switching hardware e Standard Ethernet connection LAN to customer devices e LED status indicators for power activity and signal strength e GPS ready Skyus DS models only e Skyus E Administration Interface for system configuration and monitoring e Integration with Crossroads loT application framework e Powered by the Axiom field data processing framework e Future functionality and features in firmware updates Reset LEDs Button 6 SKYUS E SRR RM m O Ss a t I i Reset 3 Ko C Signal Strength Powered by axon Mounting Plate Figure 1 Skyus E Front Panel Intended Audience This document is intended for users responsible for the configuration and management of the Skyus E and assumes the user possesses a basic working knowledge of computer networking wireless routing and network administration Scope This manual provides in depth information about Skyus E installation configuration and management See the Skyus E Quick Start Guide in the FW Literature Library for quick installation and configuration information
68. s product includes software written by Tim Hudson tjh cryptsoft com Original SSLeay License Copyright C 1995 1998 Eric Young eay cryptsoft com All rights reserved This package is an SSL implementation written by Eric Young eay cryptsoft com The implementation was written so as to conform with Netscapes SSL This library is free for commercial and non commercial use as long as the following conditions are adhered to The following conditions apply to all code found in this distribution be it the RC4 RSA Ihash DES etc code not just the SSL code The SSL documentation included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson tjh cryptsoft com Copyright remains Eric Young s and as such any Copyright notices in the code are not to be removed If this package is used in a product Eric Young should be given attribution as the author of the parts of the library used This can be in the form of a textual message at program startup or in documentation online or textual provided with the package Redistribution and use in source and binary forms with or without modification are permitted provided that the following conditions are met 1 Redistributions of source code must retain the copyright notice this list of conditions and the following disclaimer 2 Redistributions in binary form must reproduce the above copyright notice this list of conditions and the following discla
69. sclaims copyright in all jurisdictions which recognize such a disclaimer In such jurisdictions this software is released into the Public Domain In jurisdictions which do not recognize Public Domain property e g Germany as of 2010 this software is Copyright c 2007 2010 by Baptiste Lepilleur and is released under the terms of the MIT License see below 54 FW Skyus E User Manual In jurisdictions which recognize Public Domain property the user of this software may choose to accept it either as 1 Public Domain 2 under the conditions of the MIT License see below or 3 under the terms of dual Public Domain MIT License conditions described here as they choose The MIT License is about as close to Public Domain as a license can get and is described in clear concise terms at http en wikipedia org wiki MIT License The full text of the MIT License follows Copyright c 2007 2010 Baptiste Lepilleur Permission is hereby granted free of charge to any person obtaining a copy of this software and associated documentation files the Software to deal in the Software without restriction including without limitation the rights to use copy modify merge publish distribute sublicense and or sell copies of the Software and to permit persons to whom the Software is furnished to do so subject to the following conditions The above copyright notice and this permission notice shall be included in all copies or substantial portions
70. ser Manual Field Description Event mar Select the event IA TY Any Cellular System Hardware Enable Enable Debug Output Output Checkbox to enable or disable Checkbox to enable or disable debug output output c h Search on any word found in a log You can search for multiple words by putting a earc Ogg NT ATAT T character between them logTable o Table Log results sortable Log results sortable by TimeStamp Event Type Level or Message OO TimeStamp Event Type Level or Message Live Activity Displays the unsorted most recent log messages Contacting FW For help with installing operating maintaining and troubleshooting this product refer to this document and any other documentation provided The troubleshooting tips provided in Appendix A should be followed before contacting support at FW If you still have questions contact us during business hours Monday through Friday excluding holidays between 8 a m and 5 p m Pacific Time Contact Us Support E Mail 78 support feeneywireless com Telephone 800 683 4818 Website wwueeneywrelesscom Mailing Address P O Box 2549 Eugene OR 97402 When contacting technical support please have the following information on hand e Serial number on product label e Date that you received your device e A brief description of the problem Online Library For other documentation see our online document library at http feeneywireless com documents 41
71. sesscsssesscscscssesssessesesssesscsssesscsesescsssesscsesesscsesessesesesueseaessesesesseaesesesseseseeseseaeeseaeaseseaees 29 PAM AA AA AA 30 PONG a AA AA AA APAN ANA AA AA A A A 31 CO OT AA AA AA AA AA AA AA AE 33 LORNA A E AA AA 34 E oa AA AA AA 35 Ar E O aa NAA AA E E AA AA 37 CA AA tag eben va ens char basso asta garcons EE A be OET acer E ener E E A A A AAA E 37 sA AP AA AN 38 EID NALE naa AA AA ANAN AB ANNA AA AASA 39 SS Ie LOG NONA ANAN LANA AA AA ANA AA AA AA 40 CON SCN YY ca BANA TANA NAA AGA 41 Saa LIBO nA AGANG NANANA NATA NANANA ANA NA AGA ANAN 41 EXE Nd 42 Appendix A Troubles hoo O ama GGNA OAA 43 Appendix B Mounting Plate Template ssssssssscsssssscssssscsssssssssssssessssssessssssssessssssessssssesssssescsesseasssssesssessesessesesesessesessesesessssssesesceseaees 45 Appendix C Swapping ModemS ccsssssssssssssesssssscsesssscsessscsssesscsssessesesessesesesessesssessesesesseasssssesssesueseseseseseeseacsesseseseeseaesesseseaeseeseaeaseneseseeseaees 46 Appendix D Open Source Software Licenses LGA 48 TOC TV TRU ENG EAS A N AA AA PA PA PANA 48 Linux Keme CO0B dco ai NO Ga AA NANA AA 48 GNUGENERAL PUBLIC LCICEN Baa NAA AA ANNA EE AA AA AA ANN 48 PANA NA AA AA AA AA AA sce eee AA AA 48 TERMS AND CONDITIONS FOR COPYING DISTRIBUTION AND MODIFICATION ssssssssssssssssssecsesssssssssssssecsecsecsecsecsscnes 49 NOWARRANIDN sce acess cece AA AA AA AA AA AA AA eee eee 52 OpenSSL Cryptography and SSL TLS Toolkit Licens
72. the spring loaded pins pulling to compress the pins and dropping the opposite edge down over the fixed pins as shown below A how to video on attaching the Skyus E to the mounting plate is available on the Skyus E Product Page on the FW website Figure 4 Attaching the Skyus E to the Mounting Plate Connecting Antennas If you have questions about the appropriate cellular antennas for your Skyus E contact your FW representative Antennas should be located at least 20 mm from any person When using multiple separate antennas for MIMO or Receive Diversity they should optimally be separated from each other by at least 20 mm Connect the primary cellular antenna to the SMA connector on the back panel labeled Primary A second antenna can be attached to the SMA connector labeled Diversity AUX This connector is used for Receive Diversity for 3G connections or multiple input and multiple output MIMO for 4G LTE connections Connect the GPS antenna to the SMA connector labeled GPS All SMA connectors should be tightened to 8 in Ibs using a torque wrench with a 5 16 bit Power Ethernet Primary GPS Diversity AUX 9 36v Primary 5 GPS Secondary Figure 5 Antenna Connections FW Skyus E User Manual Connecting to the LAN Connect a standard RJ 45 Ethernet cable into the connector labeled Ethernet on the back of the Skyus E Connect the other end of the cable to your host computer switch or separate router Connecting
73. ti BE Administration ANS Input Voltage 14600 mv 7 a System Time 05 27 2015 21 46 05 System Logging Up Time 0 Hrs 7 Min 2 Sec Alerts 0 Notifications 7 Total Memory 505188 ke siete aaa ies a Free Memory 381924 ks QOS has been 10 or less for 2 MAC Address 1c ba 8c 9b 99 ca minutes LAN IP 192 168 66 1 W 5 27 2015 2 45 20 PM WAN IP 10 132 5 209 QOS has been 10 or less for 2 minutes System Resets 59 5 27 2015 2 46 00 PM QOS has been 10 or less for 2 minutes FW roveresy AXIOM Copyright 2015 Feeney Wireless All Rights Reserved Figure 12 System Tab FW Skyus E User Manual Description Temperature within the Skyus E in degrees Celsius as detected by the system module System Temperature Alerts will be generated if the temperature exceeds the recommended operating temperature range of the Skyus E Skyus Temperature Temperature of the Skyus radio module within the Skyus in degrees Celsius Voltage in mV millivolts detected at the Skyus E power jack The Skyus E can operate normally between 9 36V DC which is equivalent to 9000 to 36000 mV DC Note that Input Voltage in vehicle environments the Skyus E can be configured to shut down at voltages above the 9V minimum operating voltage threshold to protect the health of the vehicle battery Current date and time MM DD YYYY HH MM SS The Skyus E uses the Coordinated System Time Universal Time UTC standard Total time the Skyus E has
74. ting PATE ics cssscasteresecioneossessesarsessesaapasderuscepscesaveddubavtivsrussosdecsasesdusasyidsasgessabssseidebasyeusescssesdebuseeisinsyosesenesssnbanwoiseeiassssens 8 OS CN KAILANG AA AA AAP 9 Connecting io ine PAN NA RAANG 10 CONNEC UNG PONG NATN NANANA 10 KANA ND AA AA 10 Verntying the CONNECLIONS mma scrvesesseravesssernusrsssdecansnsronewsdsses sbuceeisgbsveenashiecssynseleossstrbsawoldvenseshdeessseucsbssaskstneveitehaseesuennoreiainesee 10 AG LED AA AA AA AA AA AA etre terete AA AA AA 11 SUI Al EN LED za a NANANA NANA NAKA KANA ANT DN EIN BANANA E NANANA 11 Resetting the KOS Pana TA ANNA BN NAA AGA AA 11 Skyus E Administra lon Inter ACS KABAGABAGAN KAANAK 12 NS DEU SERINGE aa ANA ANNA ANAN ANA AA NGA 12 EONO AA AA 12 Remote Access to the Skyus E Interface uuu ssssssssssssssssssssssscsessssscsessssscsessssscsecsessssucsessesessssucsecsssucsucsssscsucsesassucaesassucaeeassacseeassssseaeeess 13 SKyUs E BANG NAA iiini o EN EET ATEO O NE TE AOTEA 14 UMS a E AA ama E E Ana aa na 14 Ba AA S 15 a E AA AA AA AA A 17 SAE AA AA AA AA 18 AG AA AA ee 19 NG O A cots econ ccoetne cesta nseasedea E A E E 20 NEEND IKA AA AA AA ee ee AA 21 Cena Pre aI KUTA GAAN ANA AA AA AA AASA 23 Creating Port Forwarding Rule S cccssssssssssssssessssssssscsssssscsssssscsssessesssesscssssssssesssssecsssssesssesscsssessesssessesesesacsesesseaesesseasseseeeasseesesees 26 FW Skyus E User Manual Creating Routing RULES ou sesssessssesscsssesecesessssc
75. urrent Profile Sets the Skyus E to the selected profile Use As Custom APN Designates the profile as the Custom APN profile GPO IGS This tab provides the ability to enable or disable the general purpose output GPO and Ignition Sense and set IGS parameters GPO can be used to control an external device The GPO controls a pin on the Skyus E power port which can be connected to an external device such as the FW 311 Reset Board to control peripherals Ignition Sense is used in vehicle applications When ignition sense is enabled the Skyus E will not power up unless a DC voltage between 9V and 36V is applied to the ignition sense pin 31 FW Skyus E User Manual FW Skyus E Adminstration xy C ft 192 168 66 1 minutes Socket Activity CARRIER 4G LTE magdl Status Ae Network APN Crossroads Connection GPS z Configuration a Not Enable GPO Administration IL Enable Ignition Sense System Logging f l 50 Alerts 0 Notifications 10 5 27 2015 2 46 40 PM QOS has been 10 or less for 2 Voltage Shutdown Sense Disabled Y W 5 27 2015 2 47 20 PM QOS has been 10 or less for 2 minutes IT W 5 27 2015 2 48 00 PM QOS has been 10 or less for 2 minutes 4 FW roveresy AXIOM Copyright 2015 Feeney Wireless All Rights Reserved Figure 21 GPO IGS Tab Description Button to enable or disable the general purpose output GPO When enabled the Enab
76. us E It is typical when using port forwarding to manually set the IP address of the device the Port Forwarding rule is directing IP traffic to statically This prevents any possibility of that device s assigned IP address changing under certain scenarios If DHCP is used the Skyus E may assign a different IP address after a power cycle or reboot In addition if multiple devices are connected using an Ethernet switch you may find that the IP address assigned via DHCP to a given device will not be consistent from power cycle to power cycle Alternatively if only one device will ever be connected to the Skyus E LAN Ethernet interface you may wish to reduce the size of the DHCP pool to a single IP address in the Network gt DHCP Pool settings Save the rule After saving your Port Forwarding rule you should see it appear on the list of currently defined port forwarding rules The order of the Port Forwarding rules do not matter unless multiple rules are bound to the same external port in which case the rule highest on the list will take precedence In this case it is recommended that you take advantage of the Port Translation functionality in the Skyus E to choose a unique Outer Port for each device a Port Forwarding rule is required to support for a desired application 28 FW Skyus E User Manual Creating Routing Rules Creating static routing rules can be useful to instruct the Skyus E to route traffic to specific networks through an

Skyus-E User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents