Home

User Manual

1. 33 5 3 4 Value sender function 35 5 3 5 Value dimming sensor function 36 5 3 6 Step type switch function 38 5 4 Parameter window LED function 41 1 Summary The switch sensor is used in building control systems which can be mounted on a flush mounted bus coupler At the same time the application module can be also connected with other devices for a system on the bus and the functions are both simple to operation and intuitive Users can program it according to the requirement to implement the function systematically This manual provides detailed technical information about the switch sensor for users as well as assembly and programming details and explains how to use the switch sensor by the application examples The switch sensor can be used to control the switch dimming blinds and RTC etc Each single rocker switch of the switch sensor correspond one LED with seven colors indication The device can be installed in a conventional 86 mm wiring box The bus coupler that connected the switch sensor connects to the bus though the EIB connection terminals and
2. 9 5 2 2 Dimming function 10 5 2 3 Blind function 13 5 2 4 Value sender function 15 5 2 5 Scene function 17 5 2 6 Step type switch function 18 5 2 7 Short long operation function 21 5 2 8 RTC operation mode function 23 5 2 9 Multiple operation function 27 5 3 Linked working mode 29 5 3 1 Switching function 29 5 3 2 Dimming function 30 5 3 3 Blind function
3. working mode of upper lower push buttons for switching The parameter is used to determine whether operation of the upper or lower side of the rocker switch will send out an ON or an OFF telegram or a toggle telegram Options On Off Off On 31 Alternating On Off If the option alternating on off is selected you can switch between switching on and switching off for every operation that triggers a switching telegram For example if an ON telegram was last sent out then a renewed operation of the rocker switch will trigger an OFF telegram When the rocker switch is operated again an ON telegram is sent out etc The rocker switch thus always remembers the last state and then switches over to the other value Parameter working mode of upper lower push button for dimming The parameter is used to determine whether operation of the upper or lower side of the rocker switch will sent out a dim brighter or a dim darker telegram A dimming telegram that is triggered by operation of the rocker switch will be sent out on the 4 bit communication object relative dimming Options Darker Bright Bright Darker Parameter dimming stop telegram The parameter is only visible if the dimming functionality parameter is set to short operation switching long operation dimming It is used to determine whether the release of the rocker switch will trigger the dimming stop command or not Options Dimming stop is send D
4. option when triggered a durative long operation the telegram with the brighter or darker information is sent out cyclically on the 4 bit communication object relative dimming Parameter Duration of the telegram repetitions entryx0 1s 3 30 The parameter is only visible if the cyclical sending of dimming telegrams parameter is set to activated It is used to set the interval time between two telegrams that are sent cyclically options 3 30 Communication object switching 1bit 12 According to the parameter setting the object is used to send out an ON telegram or an OFF telegram or a toggle telegram via a short operation of the rocker switch Communication object relative dimming 4bit According to the parameter setting the object is used to send out a dim brighter or a dim darker telegram via a long operation of the rocker switch When the rocker switch is released it is possible that a dim stop telegram is sent out via the object 5 2 3 Blind function Parameter window blind can be shown in fig 5 4 With the application a push button has two functions to be realized shutter and roller blind In the case of shutter an operation of the rocker switch sends out a blind movement command or a slats adjustment command A short operation always triggers a travel command and a long operation always triggers a slats adjustment command You can specify whether the shutter contr
5. 20 Parameter bit pattern of object values The parameter is used to determine the way of bit pattern of object values Options x ofn lofn The three objects as an example to illustrate their difference as follows normal n 3 Xofn lofn Operations objects objects Binary code Binary code Stage3 Stage2 Stagel Stage3 Stage2 Stagel 0 000 Off Off Off 000 Off Off Off 1 001 Off Off On 001 Off Off On 2 O11 Off On On 010 Off On Off 3 111 On On On 100 On Off Off 4 111 On On On 100 On Off Off With the setting x of n the binary coding sequence of bit pattern of object values is 000 001 011 111 So the object values have changed step by step With the setting 1 of n the binary coding sequence of bit pattern of object values is 000 001 010 100 Only one of the object values is 1 for every operation and the object values have changed with certain regularity Communication object Switching stage1 to switching stage 5 1bit The number of these objects max 5 is set in the parameter Number of objects The objects send out the values or some of the values for every new operation of the rocker switch 5 2 7 Short long operation function Parameter window short long operation can be shown in fig 5 8 With the application a telegram with different predefined values can be sent out for a short or long operation of the r
6. Button pair3 Choice of function Step type switch v LED function Number of objects 1 Evaluation period entry 0 1s 10 50 30 Working mode of upper lower push buttons Up Down Sending of objects for change of value Object values normal Bit pattern of the object values xofn OK Cancel Default Fig 5 16 Parameter window step type switch Parameter Number of objects The parameter is used to specify the number of the levels Up to five levels can be switched For every level its own 1 bit communication object is available Options 1 5 Parameter Evaluation period entryx0 1s 10 50 The parameter is used to set the evaluation period i e the period of time in which complete the first object to the final object sending out via a multiple operation up to four objects can be sent Options 10 50 Parameter working mode of upper lower push buttons The parameter is used to specify whether an operation of the upper or lower side of the rocker switch switches one stage up or lower Options Up Down 38 Down Up The three objects as an example to illustrate the working mode as follows normal x of n i objects operations Binary code Stage 3 Stage2 Stage 1 0 000 Off Off Off 001 Off Off On 2 current 011 off On On 3 111 On On On 4 111 On On On With the setting up down the current operation is 2 If an operation of the upper
7. R Duration of long operation entry 0 1s 3 30 4 r lw Manner of dimming Step size for dimming Dimming functionality Working mode of upper lower push buttons for switching Working mode of upper lower push buttons for dimming Dimming stop telegram Cyclical sending of dimming telegrams Duration of the telegram repetitions entry 0 1s 3 30 Step wise dimming 444 Short operation switching long operation dimmi On Off Darker Brighter Dimming stop is not sent 10 activated OK Cancel Default Fig 5 12 Parameter window Dimming Parameter duration of long operation entryx0 1s 3 30 30 The parameter is used to define the time which a long operation is recognized Options 3 30 Parameter manner of dimming You can select between the two dimming manner start stop dimming and step wise dimming via this parameter Options Start stop dimming Step wise dimming With the start stop dimming option it means that exactly two 4 bit telegrams for dimming are always sent out For triggering of a dimming command a telegram with the information dim by 100 brighter or dim by 100 darker is sent out When the rocker switch is released the second telegram is sent out with the dimming stop information With the step wise dimming option the dimming manner is the step wise dimming You can set a telegram with t
8. for on Alarm function LED function a 1 bit off off deactivated activated 1 bit off off deactivated v Cancel Default Inf Fig 5 16 Parameter window LED function 1bit 41 1 1 5 Push Button 4 fold General LED function Button Button2 N Button3 LED1 function Button4 Ana 2 LED function LED function enable activated y Object type for status object T byte 0 100 una my Colour for Zone 1 corresponds to 0 otf Colour for Zone 2 1 to Zone 3 red Colour for Zone 3 Zone 3 to Zone 4 green Colour for Zone 4 up to 99 blue Colour for Zone 5 1007 white Threshold between Zone 2 and Zone 3 0 Threshold between Zone 3 and Zone 4 o Alarm function activated LED2 function A Cancel iL Default Fig 5 16 Parameter window LED function 1byte Parameter LED function enable It is used to set whether LED function is enabled options Deactivated Activated If the option activated is selected the object Status will be enabled Parameter Object type for status object It is used to set type for the object Status The object status can either be set to the size 1 bit or 1 byte Options 1bit 1byte With the setting 1bit the colour for off and colour for on parameters will be visible If the comm
9. rocker switch side switches one stage up the next operation will be 3 If an operation of the lower rocker switch side switches one stage lower the next operation will be 1 With the setting down up the current operation is 2 If an operation of the upper rocker switch side switches one stage lower the next operation will be 1 If an operation of the lower rocker switch side switches one stage up the next operation will be 3 Parameter sending of objects The parameter is used to specify whether the object values for every rocker switch operation are sent out or only if the object values have changed since the last sending out Options For operation For change of value Above form as an example to illustrate the difference between two options With the setting for operation the three object values are sent out for every operation Such as the above table from the 1st to the 2nd operation stage 1 object sends the value of 1 for a while stage 2 object will send the value of 1 finally stage 3 object will send the value of 0 The total time that the three objects are sent out can be set in the parameter Evaluation period entryx0 1s With the setting for change of value only the object that values have changed compared with the last values is sent out for every operation Such as the above table from the 1st to the 2nd operation only stage 2 object value has changed so only stage 2 object sends the value of 1
10. 14 Parameter window value sender Parameter object type The parameter is used to define the data type that is sent when the rocker switch is actuated for every operation The data type specified the bit size of the communication objects and the value range Options Ibit Ibyte 0 100 Ibyte 1 255 35 2byte signed 32768 32767 2byte unsigned 0 65535 2byte float 671088 64 670760 96 Abyte signed 2147483648 2147483647 4byte unsigned 0 4294967295 Parameter working mode of upper lower push buttons This parameter is used to determine whether the upper or the lower side of the rocker switch sends out the value 1 or value 2 Options Value 1 Value 2 Value 2 Value 1 Alternating Value 1 Value 2 If the option alternating valuel value2 is selected switching is always between value and value2 That means for example if valuel was last sent out then a renewed operation of the rocker switch will trigger value2 When the rocker switch is operated again value is sent out etc The rocker switch thus always remembers the last state and then switches over to the other value Parameter value1 value2 The parameters are used to specify valuel and value2 which are sent out for an operation of the upper or lower side of the rocker switch The values range is dependent on the selected data type Communication object value switching 1bit I byte 2byte 4byte The type of the
11. 2 Guangzhou Video Star Eletronnics Co Ltd K BUS Push Switch Sensor User manual Ver 1 CHKP 01 00 1 CHKP 02 00 1 CHKP 03 00 1 BTBC 01 00 1 BTBC 02 00 1 BTBC 03 00 1 Intelligent installation systems http www video star com cn Contents 1 2 3 4 5 Ki ea 3 Technical data 4 Structure and dimension diagram 5 3 1 Dimension diagram 5 3 2 Structure 6 Project design and programming 6 4 1 Overview of the functions 6 Parameter setting description in the ETS 8 5 1 Parameter window General 8 5 2 Independent working mode 9 5 2 1 Switching function
12. NN Number of the scene 0 63 1 64 in the parameter setup corresponds to the scene number 0 63 sent by the communication object Number of light scene For example scene 1 in the parameter setup has the same output result as scene 0 in the communication object Number of light scene 5 2 6 Step type switch function Parameter window step type switch can be shown in fig 5 7 With the application the user can trigger different switching processed with each new operation of the rocker switch Up to five switching levels can be activated A short and long operation can be differentiated between for the operation of the rocker switch For a short operation of the rocker switch a next level forward is switched to in each case For a long operation the first level is activated Thus a long operation can jump back from every position to the first level without having to run through the remaining levels 18 1 1 3 Push Button 4 fold General Buttoni Button2 R Button3 Choice of function Step type switch Button4 Button5 Number of objects 1 Button6 r LED function Evaluation period entry 0 1s 10 50 10 Duration of long operation entry 0 1s 3 50 10 g Sending of objects for change of value Object values normal Bit pattern of the object values xofn Lo JI Cancel I Default Fig 5 7 Parameter window step type switch Parameter Number of ob
13. Parameter object values The parameter is used to define whether the object values are sent out invert or normal via their associated 1 bit communication objects options Normal Inverse With the setting normal all 1 bit communication objects of the individual levels sent out their values normal 39 With the setting inverse all 1 bit communication objects of the individual levels sent out their values inverted The three objects as an example to illustrate the difference between two options their object values are just opposite As follows Normal Inverse Operations objects objects Binary code Binary code Stage3 Stage2 Stagel Stage3 Stage2 Stagel 0 000 Off Off Off 111 On On On 1 001 Off Off On 110 On On Off 2 O11 Off On On 100 On Off Off 3 111 On On On 000 Off Off Off 4 111 On On On 000 Off Off Off Parameter bit pattern of object values The parameter is used to determine the way of the bit pattern of object values Options x ofn lofn The three objects as an example to illustrate their difference as follows normal n 3 Xofn lofn Operations objects objects Binary code Binary code Stage3 Stage2 Stagel Stage3 Stage2 Stagel 0 000 Off Off Off 000 Off Off Off 1 001 Off Off On 001 Off Off On 2 011 Off On On 010 Off On Off 3 111 On On On 100 On Off Off 4 111 On On On 100 On Of
14. ample 5 2 Independent working mode In the independent working mode the applications do not differentiate between whether the rocker switch is operated on the upper and lower sides In each case the applications make a separate set of parameters and communication objects available for the upper and lower sides of the rocker switch For example a switching function can be realized via a rocker switch side while the other rocker switch side can be assigned with an additional button orientated function 5 2 1 Switching function Parameter window Switching can be shown in fig 5 2 With the application a switching telegram is sent out for an operation or upon release of the rocker switch 1 1 3 Push Button 4 fold General Button1 Button Button2 y Button3 Choice of function Button4 Button5 Button6 LED function Reaction on falling edge no reaction v Reaction on rising edge no reaction v Lo JI Cancel I Default Fig 5 2 Parameter window Switching Parameter Reaction on rising edge Reaction on falling edge Via the parameters you can set which 1 bit value is sent out for every operation on rising edge and falling edge This can be an ON telegram an OFF telegram or a toggle telegram Alternatively no telegram can be sent out for a rocker switch operation using the No reaction setting Options No reaction On Off Alternating on off Al
15. byte unsigned 0 4294967295 Parameter Value for object X X 1 2 3 4 5 The parameters are used to specify the value of the objects which are sent out for an 28 operation of the rocker switch The value range is dependent on its data type in the parameter Communication object Switching 1 actuation to Switching 5 actuation 1bit 1byte 2byte Abyte The type of the object is set in the parameter object type for object X X 1 2 3 4 5 the object is used to send out a telegram with the predefined value for an operation of the rocker switch The predefined value and data types can be freely selected in the parameters 5 3 Linked working mode In the linked working mode the applications differentiate between whether the rocker switch is operated on the upper and lower side of the rocker switch 5 3 1 Switching function Parameter window switching can be shown in fig 5 11 With the switching application an operation of the upper or lower side of the rocker switch sends out a switching telegram 1 1 1 Push Switch Sensor 3fold General Button pairl Button pairt Button pair2 Tene Taer Choice of funtion x LED function Working mode of upper lower push buttons On Off v OK Cancel Default Fig 5 11 Parameter window Switching Parameter working model of upper lower push buttons The parameter is used to define whether switching on or switching o
16. cts travel and adjust Options 1bit 1byte Parameter Function switchover roller blind shutter The parameter is used to determine whether a roller blind or shutter is to be driven by an operation With the roller blind setting the value for the slats adjustment does not apply Options Shutter Roller blind Parameter value for position down value for position up This parameter can only be set if 1 byte has been set as object type which can be used to set the position percent values that a connected blind shall be lowered or raised to Options 0 100 the value 096 means travel up completely the value 10096 means travel down completely Parameter value for stats position down value for stats position up This parameter can only be set if 1 byte has been set as object type which can be used to set the position percent values that a connected blind slat shall be opened or closed to Options 0 100 the value 0 means slat opened completely the value 100 means closed completely Communication object travel 1bit shutter This object is visible if the parameter object type is set to 1bit it is used to send out a shutter movement command UP or DOWN on the bus via a short operation of the rocker switch Telegram value 0 UP 1 DOWN Communication object adjust 1bit shutter This object is visible if the parameter object t
17. e The application offers two object types for output one is three 1 bit communication objects operating mode comfort operating mode night operating mode frost and the other is a 1 byte communication object operating mode In the case of 1 byte different values mean different operation modes such as 0 auto 1 comfort 2 standby etc The function can be temporarily blocked via this 1 bit enable communication object 23 W 1 1 1 Push Switching Sensor 3fold General Button1 Button Button2 i y E Button Choice of function RTC operating mode a v Button4 Button5 Object type for output Button6 LED function Operating mode Comfort Send comfort object deactivated Sending frost protection deactivated Enable object deactivated Lo JI Cancel ll Default Fig 5 9 Parameter window RTC operation mode Parameter object type for output The parameter is used to determine the size of the output communication object for the RTC operation Options lbit 1byte The selection 1 bit is used for control of room thermostats that have 1 bit communication objects for operating mode switchover The selection l byte is used for control of room thermostats that have 1 byte communication object for operation mode switchover In this case the values mean O auto 1 comfort 2 standby 3 night 4 frost heat protection 5 255 not allowed Paramet
18. ect Status 1bit Ibyte If the LED function enable parameter is set to active the object status is enabled The object status can either be set to the size 1 bit or 1 byte 1 byte value range 0 255 43 Communication object alarm 1bit If the alarm function parameter is set to active the object alarm will be enabled The LED will flash if the object receives an ON telegram If the object receives an OFF telegram the LED will no longer flash 44
19. er operating mode The parameter is used to specify the operating mode options Auto Comfort Standby Night Frost protection Heat protection The auto mode can only be set if the object type for output parameter is set to 1 byte with the selection of auto the value 0 is sent out on the lbyte object For a connected room thermostat this means that for every new operation the individual operating modes comfort standby and night will be switched between 24 If the object type for output parameter is set to 1 bit and with the selection of comfort the follow send comfort object and sending frost protection parameters will visible If the object type for output parameter is set to 1 bit and with the selection of standby the follow send comfort object sending frost protection and sending night object parameters will visible If the object type for output parameter is set to 1 bit and with the selection of night the follow send comfort object sending frost protection and sending night object parameters will visible If the object type for output parameter is set to Ibyte the value 1 is sent out on the 1 byte object and a connected room thermostat switches to the comfort operation mode the value 2 is sent out on the 1 byte object and a connected room thermosta
20. es an ON telegram the RTC function is blocked The function is active when the object enable receives an OFF telegram Parameter enable object after return of voltage The parameter is visible if the parameter enable object is set to activated which is used to defined the behavior of the communication object enable after bus voltage recovery A determination is made here about whether a 1 enabled or a 0 blocked is present on the enable object after bus voltage recovery Blocked Enable 26 If selecting blocked a 0 is present on the enable object after bus voltage recovery If the above parameter object value enable object is set to invert then the RTC function will initially be active after bus voltage recovery or else it is opposite and then here must first be activated via the receipt of an ON telegram on the enable object If selecting enable a 1 is present on the enable object after bus voltage recovery If the above parameter object value enable object is set to normal then the RTC function will initially be active after bus voltage recovery or else it is opposite and then here must first be activated via the receipt of an OFF telegram on the enable object Communication object enable 1bit This communication is visible if the parameter enable object is set to activated The object receives an ON or OFF telegram to disable
21. f Off With the setting x of n the binary coding sequence of bit pattern of object values is 000 001 011 111 So the object values have changed step by step With the setting 1 of n the binary coding sequence of bit pattern of object values is 000 001 010 100 Only one of the object values is 1 for every operation and the object values have changed with certain regularity Communication objects Switching stage1 to switching stage 5 1bit 40 The number of these objects max 5 is set in the parameter Number of objects The objects send out the values or some of the values for every new operation of the upper or the lower side of the rocker switch 5 4 Parameter window LED function Parameter window LED function can be shown in fig 5 16 Each rocker switch has a LED which can be used for status display or for the function display The LED can light up in different colours The LED can also flash for alarm display LED indication and the button operation are independent of each other Their parameters and communication objects available can be set separately 1 1 6 Push Button 4 fold General Button pairt Button pair2 LED function LED1 function LED function enable Object type for status object Colour for off Colour for on Alarm function LED2 function LED function enable Object type for status object Colour for off Colour
22. ff occurs via the upper or the lower side of the rocker switch Options On Off 29 Off On Alternating On Off If the option alternating on off is selected switching is always between ON and OFF That means for example if an ON telegram was last sent out then a renewed operation of the rocker switch will trigger an OFF telegram When the rocker switch is operated again an ON telegram is sent out etc The rocker switch thus always remembers the last state and then switches over to the other value Communication object switching 1bit According to the parameter setting the object is used to send out an ON telegram or an OFF telegram via an operation of the upper or the lower side of the rocker switch 5 3 2 Dimming function Parameter window Dimming can be shown in fig 5 12 With the dimming application an operation of the upper or lower side of the rocker switch sends out a switching telegram or a dimming telegram In the case of step wise dimming a distinction is made between short and long operation you can specify whether a short or long operation will execute switching or dimming A switching switching telegram is sent out on the 1 bit communication object A relative dimming dimming telegram is sent out on the 4 bit communication object i 1 1 Push Switch Sensor 3fold General Button pairi Button pairl Button pair2 Button pair3 Choice of function xj LED function
23. g operation of the rocker switch Telegram value 0 or 1 stop 5 2 4 Value sender function Parameter window value sender can be shown in fig 5 5 With the application two telegrams with the predefined values from two different communication objects can be sent out for an operation or upon release of the rocker switch 15 1 1 3 Push Button 4 fold General Button1 Button Button2 Button3 Button4 Button5 Object type for rising edge Button6 LED function Object type for falling edge Choice of function Reaction on rising edge no reaction Reaction on falling edge no reaction Lo JI Cancel I Default Fig 5 5 Parameter window value sender Parameter object type for rising edge object type for falling edge The parameters are used to define the data types that are sent when the rocker switch is actuated for an operation and the release The data types specified the bit size of the communication objects and the value range Options Ibit Ibyte 0 100 Ibyte 1 255 2byte signed 32768 32767 2byte unsigned 0 65535 Abyte signed 2147483648 2147483647 4byte unsigned 0 4294967295 Parameter reaction on rising edge reaction on falling edge The parameters are used to determine whether an operation and the release of the rocker switch send out the value 1 or value 2 Options No reaction Value 1 Value 2 Al
24. has no use for additional supply voltage It is available to assign the physical address and set the parameters by Engineering design tools ETS with VD3 VD4 higher than edition ETS3 The switch sensors have many functions that can be used in a wide variety of application areas The following list provides an overview gt switching and dimming gt control of blinds and shutters gt Sending of values e g water line brightness gt recall and storage scene gt step type switch gt setting the RTC operation mode gt Multiple operation gt LED indication Each rocker switch of a device can adopt any of the functions described above and is independent of each other Almost each function has two operating modes one is that the function differentiates between whether the rocker switch is operated on the upper or lower push buttons the other is that the function does not differentiate between whether the rocker switch is operated on the upper or lower push buttons 2 Technical data Power supply Operating and display Number of button operation connections Temperature rang Design Installation Weight Housing color Approvals CE mark Bus voltage Current consumption bus Power consumption bus Corresponding 1 LED indication for each rocker switch Programming LED and button gt 20000 EIB KNX Operation Storage Transport Embedded installation of equipment Dimensions in a conventio
25. he brighter or darker information whether is sent out cyclically by a long operation And when the rocker switch is released you can also set the telegram with the dimming stop information whether is sent out Parameter step size for dimming The parameter is only visible if the manner of dimming parameter is set to step wise dimming Here you can specify by how much brighter or darker dimming should occur The sent out value always relates to the current brightness value For example a dimming actuator is currently dimmed to a brightness value of 70 By operation of the rocker switch a dimming command dim by 25 1 4 brighter is sent out The dimming actuator will adjust its brightness value to 95 immediately after receiving the dimming command Options 1 1 1 2 1 4 1 32 1 64 Parameter dimming functionality The parameter is only visible if the manner of dimming parameter is set to step wise dimming It is used to define the functionality of the dimming You can set whether a switching telegram will be sent out for a short operation of the rocker switch and a dimming telegram will be sent out for a long operation or whether a long operation will cause a switching telegram to be sent out and a short operation will cause a dimming telegram to be sent out Options Short operation dimming long operation switching Short operation switching long operation dimming Parameter
26. imming stop is not send With the dimming stop is send option when the rocker switch is released the telegram with the dimming stop information is sent out on the 4 bit communication object relative dimming Parameter cyclical sending of dimming telegrams The parameter is only visible if the dimming functionality parameter is set to short operation switching long operation dimming It is used to determine the telegram with the brighter or darker information whether is sent out cyclically by a durative long operation Options Deactivated Activated With the activated option when triggered a durative long operation the telegram with the brighter or darker information is sent out cyclically on the 4 bit communication object relative dimming Parameter Duration of the telegram repetitions entryx0 1s 3 30 The parameter is only visible if the cyclical sending of dimming telegrams parameter is set 32 to activated It is used to set the interval time between two telegrams that are sent cyclically options 3 30 Communication object switching 1bit According to the parameter setting the object is used to send out an ON telegram or an OFF telegram via an operation of the upper or the lower side of the rocker switch Communication object relative dimming 4bit According to the parameter setting the object is used to send out a dim b
27. ing stop is not sent Cyclical sending of dimming telegrams deactivated OK Cancel Default Fig 5 3 Parameter window Dimming Parameter duration of long operation entryx0 1s 3 30 The parameter is used to define the time which a long operation is recognized Options 3 30 Parameter working mode of the push button for switching This parameter is used to determine whether a short operation sends out an ON or an OFF telegram via a 1 bit communication object Alternatively for the selection alternating on off you can switch between switching on and switching off for every short operation i e after a switch on telegram has been sent out or received a switch off telegram will be sent out for a renewed operation After it is operated again a switching on telegram is sent out Options Deactivated Off On Alternating on off Parameter working mode of the push button for dimming This parameter is used to determine whether a long operation sends out a dim brighter or a dim darker telegram via a 4 bit communication object Alternatively for the selection alternating brighter darker you can switch between dimming up and dimming darker for every long operation i e after a dim brighter telegram has been sent out or received a dim darker telegram will be sent out for a renewed operation After it is operated again a dim brighter telegram is sent 11 out Options Darker Bright A
28. ith storage function With the application a short operation will recall a scene and a long operation will storage the current scene for the rocker switch Step type switch The application is used to trigger different switching processed with each new operation of the rocker switch Up to five switching levels can be activated An operation of the upper or lower side of the rocker switch makes switching processed change to a stage higher or a stage lower Or a short operation of the rocker switch will make switching processed change to a next level forward and a long operation will make switching processed back to the first level from every position Short long operation With the application the different values can be sent out by a short operation or a long operation for the rocker switch Setting the RTC operation mode The application can be used for adjusting the room thermostat According to room temperature humidity refrigeration cycle etc you can switch to a different working mode such as comfort standby night frost protection or heat protection Multiple operations With the application an operation of the rocker switch can send up to 5 different values to the bus to control 5 different output loads LED function LED can be used for status display or the function display The LED can light up in different colors and can also flash for alarm display 5 Parameter setting description in the ETS 5 1 Parameter wi
29. jects The parameter is used to specify the number of the levels Up to five levels can be switched For every level its own 1 bit communication object is available Options 1 5 Parameter Evaluation period entryx0 1s 10 50 The parameter is used to set the evaluation period i e the period of time in which complete the first object to the final object sending out via an operation up to five objects can be sent Options 10 50 Parameter duration of long operation entryx0 1s 3 50 The parameter is used to define the time which a long operation is recognized and switched back to the first level Options 3 50 Parameter sending of objects The parameter is used to specify whether the object values for every rocker switch operation are sent out or only if the object values have changed since the last sending out Options For operation For change of value The three objects as an example to illustrate the difference between two options normal x of n objects Operations Binary code Stage3 Stage2 Stagel 0 000 Off Off Off 001 Off Off On 2 011 Off On On 19 111 On On On 111 On On On With the setting for operation the three object values are sent out for every operation Such as the above table from the Ist to the 2nd operation stage 1 object sends the value of 1 for a while stage 2 object will send the value of 1 finally
30. le when the parameter object type for output is set to bit here set whether the frost heat protection mode is activated Options Deactivated 25 Activated When selecting activated option the communication object frost operating mode is enabled Parameter send night object This parameter will be visible when the parameter object type for output is set to 1bit here set whether the night mode is activated Options Deactivated Activated When selecting activated option the communication object night operating mode is enabled Parameter enable object This parameter is used to set whether enable the 1bit communication object enable Options Deactivated Activated If selecting activated the communication object enable is enabled and the RTC function can temporarily be blocked via the object If selecting deactivated the RTC function is always enabled Parameter object value enable object This parameter is only visible if the parameter enable object is set to activated Options Normal Invert If selecting normal the RTC function is normally enabled the function is active when the object enable receives an ON telegram The function is blocked when the object enable receives an OFF telegram If selecting invert the above described behavior can be reversed i e when the object enable receiv
31. lternating brighter darker Parameter step size for dimming The parameter is used to specify by how much brighter or darker dimming should occur The sent out value always relates to the current brightness value For example a dimming actuator is currently dimmed to a brightness value of 70 By operation of the rocker switch a dimming command dim by 25 1 4 brighter is sent out The dimming actuator will adjust its brightness value to 95 immediately after receiving the dimming command Options 1 1 1 2 1 4 1 32 1 64 Parameter dimming stop telegram The parameter is used to determine whether the release of the rocker switch will trigger the dimming stop command or not Options Dimming stop is send Dimming stop is not send With the dimming stop is send option when the rocker switch is released the telegram with the dimming stop information is sent out on the 4 bit communication object relative dimming Parameter cyclical sending of dimming telegrams The parameter is used to determine the telegram with the brighter or darker information whether is sent out cyclically by a durative long operation Options Deactivated Activated With the deactivated option when triggered a durative long operation only one telegram with the brighter or darker information is sent out on the 4 bit communication object relative dimming With the activated
32. lue for every operation Parameter Step size The parameter is used to determine how large the percent value or the absolute value will be increased or reduced for every operation For example the current value is 40 for a step size of 10 and then the current value is increased from 40 to 50 for an operation for an increase Parameter working mode of upper lower push buttons The parameter is used to determine whether the operation of the upper or lower side of the rocker switch increased or lowers the value that is sent out from the 1 byte communication object value Options Bright Darker Darker Bright Communication object value I byte The type of the object value is set in the parameter object type The object is used to send out a telegram with the predefined value for an operation of the upper or the lower side of the 37 rocker switch The predefined value is set in the parameter step size Telegram value 0 50 Or 0 127 5 3 6 Step type switch function Parameter window step type switch can be shown in fig 5 16 With the application the user can trigger different switching processed with each new operation of the upper or lower side of the rocker switch Up to five switching levels can be activated Depending on the setting a stage higher or a stage lower can thus be switched to W i 1 1 Push Switch Sensor 3fold General Button pairl Button pairl Button pair2
33. nal 86 mm wiring box 0 1KG application module 0 1KG coupler 21 30V DC via the EIB bus lt 12mA lt 360mW The LEDs have seven colors For assignment of the physical address Via bus connection terminal 8 Cie AS IE 25 AE sina SS AE 2 CS co WO ME 86x86mm application module 50 7 X 45 46 X 23 1mm coupler Plastic housing white gray yellow blue pink black EIB KNX certificate In accordance with the EMC guideline and low voltage guideline 3 Structure and dimension diagram 3 1 Dimension diagram 23 6 2 B aa 0 CHKP 03 00 1 45 46 mm BTBC 01 00 1 3 2 Structure EIB bus cable Bus coupler EIB bus connect terminal Application module GN TP Ge a 10 pin plug to connect application module and the coupler 4 Project design and programming 4 1 Overview of the functions Max number of Max number of Max number of Application program communication objects group addresses associations Push switch sensor 1fold 12 24 24 Push switch sensor 2 fold 24 48 48 Push switch sensor 3fold 36 72 72 The following applications can be set separately for each rocker switch of the switch sensor Switch The application can be used for switching the lighting such as relay dimmer etc With the application an operation of the upper or lower side of the rocker switch sends out a switching command Or an operation or upon release of the rocker
34. ndow General Parameter window General can be shown in fig 5 1 There used to set the working mode for each rocker switch the rocker switch can be used as two independent push button or linked push button If the rocker switch is used as two independent push button the application is independent each other for the two push button If as linked push button the application is associated W 1 1 1 Switch Genera Buttont Button2 Button3 Button4 LED function Button 3 4 use 2 independent push button Button 1 2 use 2 independent push button Ok Cancel Defaut Fig 5 1 Parameter window General Parameter Button 1 2 3 4 use This parameter is used to set the working mode for each rocker switch Options 2 independent push buttons Linked push button If selecting 2 independent push buttons the upper and lower sides of the rocker switch are used as two independent push buttons and the application does not differentiate between whether the rocker switch is operated on the upper and lower sides If selecting linked push button the upper and lower sides of the rocker switch are used as linked push button and the application differentiates between whether the rocker switch is operated on the upper and lower sides The following sections details parameters and communication objects of each application in the two working modes using one push button or one rocker switch as an ex
35. nt For a short operation of the rocker switch a moving up or down telegram is sent out on a 1 bit communication object For a long operation of the rocker switch a slat adjustment up or down telegram is sent out on a 1 bit communication object Options Down Up Up Down Parameter value for position down value for position up This parameter can only be set if 1 byte has been set as object type which can be used to set the position percent values that a connected blind shall be lowered or raised to Options 0 100 the value 096 means travel up completely the value 10096 means travel down completely Parameter value for stats position down value for stats position up This parameter can only be set if 1 byte has been set as object type which can be used to set the position percent values that a connected blind slat shall be opened or closed to Options 0 100 the value 0 means slat opened completely the value 100 means closed completely Communication object travel 1bit This object is visible if the parameter object type is set to 1bit it is used to send out a shutter movement command UP or DOWN on the bus via a short operation of the upper or the lower side of the rocker switch Telegram value 0 UP 1 DOWN Communication object adjust 1bit This object is visible if the parameter object type is set to 1bit it is used to send ou
36. object is set in the parameter object type the object is used to send out a telegram with the predefined value for an operation of the upper or the lower side of the rocker switch The predefined value and data types can be freely selected in the parameters 5 3 5 Value dimming sensor function Parameter window value dimming sensor can be shown in fig 5 15 With the application each operation of the upper or lower side of the rocker switch will increase or reduce a 1 byte value percent or value from 0 to 127 via sending a 1 byte telegram The 1 byte value can be connected with 1 byte brightness value objects from dimming actuators Thus a dimming actuator can be dimmed brighter or darker 36 i 1 1 Push Switch Sensor 3fold General Button pairl Button pairl Button pair2 Button pair3 Choice of function Value dimming sensor v LED function Object type 1 byte 0 100 Step size 0 50 0 i Working mode of upper lower push buttons Brighter Darker v OK Cancel Default Fig 5 15 Parameter window value dimming sensor Parameter object type The parameter is used to set the 1 byte communication object value Options 1byte 0 100 1byte 0 255 With the setting l byte 0 100 the momentary value is increased or reduced by a percent amount for every operation With the setting 1l byte 0 255 the momentary value is increased or reduced by an absolute va
37. ocker switch 21 1 1 3 Push Button 4 fold General Buttoni Button2 Button3 Button4 Button5 Object type 1 bit Button6 LED function Reaction on short operation Value 1 Choice of function Short long operation Value 1 for short operation off Reaction on long operation Value 2 Value 2 for long operation off Duration of long operation entry 0 1 s 3 30 4 Lo JI Cancel IN Default Fig 5 8 Parameter window short long operation Parameter object type The parameter is used to define the data types that are sent when the rocker switch is actuated via a short or long operation The data types specified the bit size of the communication objects and the value range Options Ibit 1byte 0 100 Ibyte 1 255 2byte signed 32768 32767 2byte unsigned 0 65535 4byte signed 2147483648 2147483647 4byte unsigned 0 4294967295 Parameter reaction on short operation The parameters are used to determine whether the rocker switch sends out the valuel or value2 via a short operation Options No reaction Value 1 Value 2 Alternating value 1 value 2 Parameter value 1 2 for short operation The parameters are used to specify value and value2 which are sent out for a short operation of the rocker switch The values range is dependent on the selected data type Parameter reaction on long operation The parameters are used
38. ol occurs via two 1 bit or two 1 byte communication objects travel and adjust If the communication object adjust is selected to 1 bit the slats adjustment command can be sent out cyclically In the case of roller blind a short operation triggers a travel command and a long operation trigger a stop command the blind control occurs via two 1 bit communication objects travel and stop W 1 1 2 Push Switch Sensor 3fold General Button Button Button2 Button3 Button4 Button5 Duration of long operation entry 0 1 s 3 30 Button6 LED function Cycle time of the telegram repetition entry 0 1s 3 30 Choice of function Object type 1 bit Function switchover blinds roller shutters Shutter OK Cancel Default Fig 5 4 Parameter window Blind Parameter duration of long operation entryx0 1s 3 30 The parameter is used to define the time which a long operation is recognized Options 3 30 Parameter cycle time of the telegram repetition entryx0 1s 3 30 13 The parameter is only visible if the object type parameter is set to 1 bit It is used to set the interval time between two telegrams that are sent cyclically for a durative long operation options 3 30 Parameter object type This parameter is only visible if the function switchover blinds roller shutter parameter is set to shutter It is used to define the type of the communication obje
39. old General Button1 Button Button2 Button3 Button4 Button Number of objects Choice of function Multiple operation Button6 LED function Evaluation period entry 0 1s 10 50 Object type for object1 1 bit Function for object type 1bit for object1 Transmit value Value for object 1 bit off Object type for object2 1 byte 0 100 Value for object 1 byte 0 100 0 Object type for object3 2 byte unsigned Value for object3 2byte unsigned 0 OK Cancel Default Fig 5 10 Parameter window Multiple operation Parameter Number of objects The parameter is used to specify the number of the objects Up to five objects can be set Options 1 5 Parameter Evaluation period entryx0 1s 10 50 The parameter is used to set the evaluation period i e the period of time in which complete the first object to the final object sending out via an operation of the rocker switch up to five objects can be sent Options 10 50 Parameter object type for object X X 1 2 3 4 5 The parameter is used to define the data types for the objects that are sent when the rocker switch is actuated via an operation The data types specified the bit size of the communication objects and the value range Options Ibit Ibyte 0 100 Ibyte 1 255 2byte signed 32768 32767 2byte unsigned 0 65535 2byte float 671088 64 670760 96 Abyte signed 2147483648 2147483647 4
40. old between Zone 2 and Zone 3 is 20 the threshold between Zone 3 and Zone 4 is 70 When the object Status received a telegram 096 the LED takes on the colour in the parameter colour for Zone 1 corresponds to 0 setting when the object received a telegram 1 to 20 the LED takes on the colour in the parameter colour for Zone 2 1 to Zone3 setting when the object received a telegram 21 to 70 the LED takes on the colour in the parameter colour for Zone 3 Zone3 to Zone4 setting when the object received a telegram 71 to 99 the LED takes on the colour in the parameter colour for Zone 4 up to 99 setting when the object received a telegram 100 the LED takes on the colour in the parameter colour for Zone 5 100 setting Parameter alarm function This parameter is used to define whether the alarm function is enabled for the LED Options Deactivated Active If the option active is selected the alarm function will be switched active and the object alarm will be enabled The LED will flash if the object receives an ON telegram If the object receives an OFF telegram the LED will no longer flash Note In the case of LED no indication the LED flashes red when the alarm is enabled If the LED takes on one colour it will flashes in the same colour If the LED status is turned into off the flashing colour will change back to red again Communication obj
41. or enable the RTC function Communication object Comfort operating mode 1bit This communication is visible if the parameter send comfort object is set to activated If the object receives an ON telegram a connected room thermostat switches to the comfort operation mode Communication object Frost operating mode 1bit This communication is visible if the parameter send frost protection is set to activated If the object receives an ON telegram a connected room thermostat switches to the frost heat protection operation mode Communication object Night operating mode 1bit This communication is visible if the parameter send night object is set to activated If the object receives an ON telegram a connected room thermostat switches to the night operation mode Communication object Operation mode 1byte This communication is visible if the parameter object type for output is set to 1byte The object sends out different telegram values different values mean different operation modes such as 0 auto 1 comfort 2 standby 3 night 4 or Frost protection Heat protection values 5 255 is not allowed 5 2 9 Multiple operation function Parameter window Multiple operation can be shown in fig 5 10 With the application up to five telegrams with different predefined values can be sent out for an operation of the rocker switch 27 W i 1 1 Push Switch Sensor 3f
42. righter or a dim darker telegram or a dim stop telegram via an operation of the upper or the lower side of the rocker switch 5 3 3 Blind function Parameter window blind can be shown in fig 5 13 With the blind application an operation of the upper or lower side of the rocker switch sends out a blind movement command or a slats adjustment command A short operation always triggers a travel command and a long operation always triggers a slats adjustment command You can specify whether the blind control occurs via two 1 bit or two 1 byte communication objects travel and adjust i 1 1 Push Switch Sensor 3fold General Button pairl Button pairl Button pair2 Epee Cheice of uncon x LED function Duration of long operation entry 0 1s 3 30 4 Object type 1 bit Working mode of upper lower push buttons Up Down OK Cancel Default Fig 5 13 Parameter window Blind Parameter duration of long operation entryx0 1s 3 30 The parameter is used to define the time which a long operation is recognized Options 3 30 Parameter object type 33 This parameter is used to define the type of the communication objects travel and adjust Options Ibit 1byte Parameter working mode of upper lower push buttons The parameter is used to determine whether operation of the upper or lower side of the rocker switch will send out commands for movement and adjustme
43. stage 3 object will send the value of 0 The total time that the three objects are sent out can be set in the parameter Evaluation period entryx0 1s With the setting for change of value only the object that values have changed compared with the last values is sent out for every operation Such as the above table from the 1st to the 2nd operation only stage 2 object value has changed so only stage 2 object sends the value of 1 If the rocker switch is a long operation the operation is switched back to the 0 operation i e 000 Parameter object values The parameter is used to define whether the object values are sent out invert or normal via their associated 1 bit communication objects options Normal Inverse With the setting normal all 1 bit communication objects of the individual levels sent out their values normal With the setting inverse all 1 bit communication objects of the individual levels sent out their values inverted The three objects as an example to illustrate the difference between two options their object values are just opposite As follows Normal Inverse Operations objects objects Binary code Binary code Stage3 Stage2 Stagel Stage3 Stage2 Stagel 0 000 Off Off Off 111 On On On 1 001 Off Off On 110 On On Off 2 O11 Off On On 100 On Off Off 3 111 On On On 000 Off Off Off 4 111 On On On 000 Off Off Off
44. switch sends out a switching command Switch Dimming The application can be used for switching dimming the lighting and is distinguished between long and short operation The manner of dimming can be selected between start stop dimming and step wise dimming With the application an operation of the upper or lower side of the rocker switch sends out a switching command or a dimming command Or a short operation will execute switching and a long operation will execute dimming for the rocker switch Blind and Shutter The application can make the Shutter or Roller blind movement or lamella adjustment and there is distinguish between long and short operation a short operation will execute movement and a long operation will execute adjustment stop for the rocker switch Value sender The application can be used for sending the different values or data types With the application an operation of the upper or lower side of the rocker switch sends out the different values Or an operation and upon release of the rocker switch send out the different values or data types Value dimming With the application each operation of the upper or lower side of the rocker switch will increase or reduce a 1 byte value percent or value from 0 to 127 via sending a 1 byte telegram The 1 byte value can be connected with 1 byte brightness value objects from dimming actuators Thus a dimming actuator can be dimmed brighter or darker Light scene control w
45. t a lamella adjustment command UP or DOWN on the bus via a long operation of the upper or the lower side of the rocker switch Telegram value 0 lamella UP 1 lamella DOWN Communication object position Ibyte This object is visible if the parameter object type is set to 1byte it is used to send out a shutter movement command UP or DOWN percent values on the bus via a short operation of 34 the upper or the lower side of the rocker switch Telegram 0 100 O travel up completely 100 travel down completely Communication object Slats position Ibyte This object is visible if the parameter object type is set to lbyte it is used to send out a slats adjustment command UP or DOWN percent values on the bus via a long operation of the upper or the lower side of the rocker switch Telegram 0 100 O slats opened completely 100 slats closed completely 5 3 4 Value sender function Parameter window value sender can be shown in fig 5 14 With the application a telegram with the predefined value is sent out for an operation of the upper or the lower side of the rocker switch i 1 1 Push Switch Sensor 3fold General Button pairl Button pairt Fpa Choice of functi Button pair3 hoice of function aoa ena LED function Object type 1 bit Working mode of upper lower push buttons Valuel Value2 Valuel off Value2 off OK Cancel Default Fig 5
46. t switches to the standby operation mode the value 3 is sent out on the 1 byte object and a connected room thermostat switches to the night operation mode the value 4 is sent out on the 1 byte object and a connected room thermostat switches to the Frost Heat protection operation mode If the object type for output parameter is set to bit when the object comfort operating mode sends a telegram 1 on operating switch and other objects send telegrams 0 right now a connected room thermostat switches to the comfort operation mode when the object night operating mode sends a telegram 1 on operating switch and other objects send telegrams 0 right now a connected room thermostat switches to the night operation mode when all objects send telegrams 0 on operating switch right now a connected room thermostat switches to the standby operation mode When the operation mode is set to the Frost Heat protection operation mode other operation modes of communication objects and parameters will be not visible Parameter send comfort object This parameter will be visible when the parameter object type for output is set to Ibit here set whether the comfort mode is activated Options Deactivated Activated When selecting activated option the communication object comfort operating mode is enabled Parameter sending frost protection This parameter will be visib
47. ternating on off means that switching is always between ON and OFF For example if an ON telegram was last sent out then a renewed operation of the rocker switch will trigger an OFF telegram When the rocker switch is operated again an ON telegram is sent out etc The rocker switch thus always remembers the last state and then switches over to the other value Communication object switching 1bit According to the parameter setting the object is used to send out an ON telegram or an OFF telegram or a toggle telegram via an operation or the releasing of the rocker switch 5 2 2 Dimming function Parameter window Dimming can be shown in fig 5 3 With the application a push button has two communication objects for switching and for dimming A distinction is made between short operation and long operation A short operation will execute switching a long operation will 10 execute dimming A switching switching telegram is sent out on the 1 bit communication object A relative dimming dimming telegram is sent out on the 4 bit communication object i 1 1 Push Switch Sensor 3fold General Button Buton Button2 Button3 Button4 Button5 Duration of long operation entry 0 1 s 3 30 4 Button LED function Waorking mode of the button for switching deactivated Choice of function Dimming Working mode of the button for dimming darker Step size for dimming 174 Dimming stop telegram Dimm
48. ternating value 1 value 2 Parameter valuel for rising edge value2 for rising edge The parameters are used to specify valuel and value2 which are sent out for an operation of the rocker switch The values range is dependent on the selected data types Parameter valuel for falling edge value2 for falling edge The parameters are used to specify valuel and value2 which are sent out for the release of the 16 rocker switch The values range is dependent on the selected data type Communication object switching rising edge 1bit 1byte 2byte 4byte The type of the object is set in the parameter object type for rising edge the object is used to send out a telegram with the predefined value for an operation of the rocker switch Communication object switching falling edge 1bit 1byte 2byte 4byte The type of the object is set in the parameter object type for falling edge the object is used to send out a telegram with the predefined value for the release of the rocker switch 5 2 5 Scene function Parameter window Scene can be shown in fig 5 6 With the application a predefined light scene number can be recalled for an operation of the rocker switch The user has the option to trigger a light scene storage command via a long operation 1 1 3 Push Button 4 fold General Button1 Buttont Button2 Button3 Button4 cee Storage function ight scenes fwd Button6 LED function D
49. to determine whether the rocker switch sends out the value1 or 22 value2 via a long operation Options No reaction Value 1 Value 2 Alternating value 1 value 2 Parameter value 1 2 for long operation The parameters are used to specify valuel and value2 which are sent out for a long operation of the rocker switch The values range is dependent on the selected data type Parameter duration of long operation entryx0 1s 3 30 The parameter is used to define the time which a long operation is recognized Options 3 30 Communication object Value for short operation 1bit 1byte 2byte 4byte The type of the object is set in the parameter object type the object is used to send out a telegram with the predefined value for a short operation of the rocker switch The predefined value and data types can be freely selected in the parameters Communication object Value for long operation Lbit Ibyte 2byte 4byte The type of the object is set in the parameter object type The object is used to send out a telegram with the predefined value for a long operation of the rocker switch The predefined value and data types can be freely selected in the parameters 5 2 8 RTC operation mode function Parameter window RTC operation mode can be shown in fig 5 9 With the application an operation mode switchover for connected room thermostats can be carried out for an operation of a rocker switch sid
50. unication object Status received an ON telegram the LED takes on the colour that is stored in the colour for on parameter If the communication object Status received an OFF telegram the LED takes on the colour that is stored in the colour for off parameter With the setting 1 byte the colour for Zone 1 corresponds to 0 colour for Zone 2 1 to Zone 3 and colour for Zone 5 100 parameters will be visible When a value telegram is received on the object Status the LED takes on the colour that depends on the parameter settings colour for Zone Note the LED function is not action after voltage recovery unless the object received a telegram and the LED will take on the colour according to the parameter settings 42 Parameter colour for off on or colour for Zone These parameters are used to set the colour that the LED takes on when the object Status received a telegram Options Off Parameter Threshold between Zone2 and Zone 3 Zone3 and Zone 4 This parameter is visible in the parameter object type for status object with 1 byte 0 100 In this type of case LED indication can be divided into five Zone the colour that the LEDs take on for each Zone can be set in the parameter colour for Zone Here the parameter is used to set the threshold between Zone 2 and Zone 3 Zone 3 and Zone 4 For example assume the thresh
51. uration of long operation entry 0 1s 3 100 30 Choice of function Scene Number of scene 1 64 1 a Cancel Default Fig 5 6 Parameter window Scene Parameter storage function light scenes Itis used to set whether the light scene storage function is enabled options Deactivated Activated With the setting activated the user has the option of sending out a light scene storage command via a long operation The same 1 byte communication object that is used for this can also recall the light scene number via a short operation Parameter duration of long operation entryx0 1s 3 100 17 The parameter is only visible if the storage function light scenes parameter is set to activated It is used to define the time which a long operation is recognized Options 3 100 Parameter number of light scene 1 64 The parameter is used to set an arbitrary light scene number from 1 to 64 which can be sent out via the 1 byte communication object light scene number for operation of the rocker switch Communication object Number of light scene Ibyte The object is used to send out a scene number and the information as to whether a scene should be recalled or the current scene should be stored The number of light scene is set in the parameter Number of light scene Telegram code 8 bit FXNNNNNN F Q Scene is recalled 1 Scene is stored X Not used NNNN
52. ype is set to 1bit it is used to send out a lamella adjustment command UP or DOWN on the bus via a long operation of the rocker switch Telegram value 0 lamella UP 1 lamella DOWN Communication object travel 1byte shutter This object is visible if the parameter object type is set to 1byte it is used to send out a 14 shutter movement command UP or DOWN percent values on the bus via a short operation of the rocker switch Telegram 0 100 O travel up completely 100 travel down completely Communication object adjust 1byte shutter This object is visible if the parameter object type is set to byte it is used to send out a slats adjustment command UP or DOWN percent values on the bus via a long operation of the rocker switch Telegram 0 100 0O stat opened completely 100 stat closed completely Communication object travel 1bit roller blind This object is visible if the parameter function switchover roller blind shutter is set to roller blind it is used to send out a roller blind movement command UP or DOWN on the bus via a short operation of the rocker switch Telegram value 0 UP 1 DOWN Communication object stop 1bit roller blind This object is visible if the parameter function switchover roller blind shutter is set to roller blind which is used to send out a roller blind stop telegram on the bus via a lon

User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents