OFC-1000PSE User Manual
Contents
1. forced Half Duplex for either 10Base or 100Base or sets Full Duplex when OFF up Switch 4 is used to enable the LFP Link Fault Pass Thru function LFP is enabled when the switch is ON down DIP Setting ON yy OFF 48 gggn UTPNWAY AAA 1000 FULL 100 FULL A vA 100 HALF 4 W v 40 FULL W 10 HALF Wi viv IGNORE KY Link Fault Pass Through LFP Note This media converter incorporates a fiber link pass through feature which allows indirect sensing of a fiber link loss via 10 100 1000 Base TX UTP connection Whenever the media converter detects a link loss condition on the receive fiber FX LNK Off it disables its UTP transmitter so that a link loss condition is sensed on the receive UTP port See the following figure The link loss can then be sensed and reported by network management agent at the remote UTP port s host equipment The LFP feature has no effect on the media converter s UTP Link LED which continues to function normally independent of the state of the fiber LNK LED and the UTP transmitter This feature is disabled by default from the factory ae x Be RX OFF LE gt gt By Fiber Link Remote Fault Fail Figure Fiber Break Responses sales ctcu com2. Introduction The IFC 1000PSE is an electrical copper to optical fiber Gigabit Ethernet solution designed to make conversion between 10 100 1000Base T and 1000Base SX LX with SFP module The IFC 1000PSE complies with IEEE802 3af Power Over Ethernet standards and has a built in AC power supply This PoE Power over Ethernet media converter is a Power Sourcing Equipment PSE which combines data received over a TP link with 48VDC power providing power to IEEE802 3af powered device PD over the existing CAT5e or CAT6 UTP cable Other features include Link Fault Pass through LFP Store and Forward Switching and auto or forced mode setting for copper Ethernet Features 10 100 1000Base T to 1000Base SX LX SFP IEEE 802 3af 2003 PSE power sourcing equipment Auto negotiation or forced mode on UTP Auto MDI MDIX Store and Forward Switching Mechanism Forward 1632 bytes max packet Supports 4k MAC address Supports 256K bytes packet buffer Supports Link Fault Pass through LFP function For applications including IP Cameras IP phone and wireless Access Points that require less than 15W sales ctcu com GbE PSE Converter Dip Switch 10 100 1000T GbE Port with PSE 48V 15W LED Indicator SPD Duplex LFP 1000X SFP Cage shown with SFP e Figure 1 Front Panel of IFC 1000PSE CTC union GbE PSE Converter TX FIBER RX N I o T lt lt gt o N 8 DCIN 48VDC 0 5A O e sales
3. LNK UTP LNK vais se Sans Converter Power Fiber link Status Power on Power off PSE power in use PSE standby Fiber link is ok No Fiber link 100 1000 LAN Speed Status 1000Mbps 100Mbps 10Mbps LAN Duplex mode UTP LNK UTP link Status sales ctcu com Full duplex Half duplex UTP link is ok No UTP link Installation Connect the Ethernet cable to the IFC 1000PSE The converter will sense whether to operate in Full or Half mode and will be indicated on the LED Follow the connection examples below Connections The following example illustrates the connection scheme when connecting from IP Camera and VoIP Phone to 10 100 1000Base T UTP port through the IFC 1000PSE fiber converter Central Office CO Customer Premise Equipment CPE IFC 1000PSE A IP Camera Fiber 4 Ethernet g fi pian Data power gt NMS N IEEE 802 30f PSE J IP Networking Router Switch ar FRM220 1000MS Inserts in FRM220 IFC 1000PSE A VoIP Phone Chassis Fiber Ethernet A amp Data power IEEE 802 3af PSE sales ctcu com Dip Switch Setting The IFC 1000PSE is provisioned through the use of a single 4 pole DIP Dual Inline Package switch located on the front panel Setting a switch down places it in the ON position Switches 1 amp 2 provide setting auto negotiation Nway or manual forced speed of 10 100 or 1000 Default is all OFF Switch 3 when ON down sets the
4. ctcu com EE EEE a EE E EE a sg wc a cg a E a a ce ee TC CTC Union Technologies Co Ltd www ctcu com union User Guide Gigabit Ethernet PSE Fiber Media Converter eIFC 1000PSE AC eIFC 1000PSE A GbE PSE Converter sales ctcu com Specifications Standards IEEE802 3 10Base T IEEE802 3u 100Base TX IEEE802 3ab 1000Base T 802 3z 1000Base SX LX IEEE802 3x flow control TEEE802 3af 2003 PSE Power Sourcing Equipment 10 100 1000Base T RJ 45 Connectors One RJ 45 connector is provided for connection to either MDI X to PC or MDI to HUB equipment Utilizing auto MDI MDIX allows all UTP connections to be made using only a common straight through UTP cable PSE Output Power Class0 15 4W Class 1 4W Class2 7W Class3 15 4 w RJ 45 Pin Assignment Pinl TX RX A V Pin5 TX RX C Pin2 TX RX A V Pin6 TX RX B V Pin3 TX RX B V Pin7 TX RX D Pin4 TX RX C Pin8 TX RX D Fiber Optic Connectors One SFP cage is provided for SFP fiber optic transceiver IFC 1000PSE with SFP requires duplex LC connector cable SFP for single fiber BiDi may have single LC or SC connector Environment Temperature Operating 0 to 50 C Storage 0 to 70 C Humidity 10 to 90 non condensing Power IFC 1000PSE AC Internal AC 100 240VAC 10 IFC 1000PSE A External DC 48V in AC adapter Dimensions 147 x 162 x 36 D x W x H mm Net Weight 405g sales ctcu com LED Indicators PWR 100 1000 PSE FULL FX
Download Pdf Manuals
Related Search