TIENet 306 Sampler Interface User Manual
Contents
1. 10m or 23m cable For greater dis tances external connection via conduit and connection of addi tional TIENet devices the TIENet Expansion Box is available Bulk TIENet cable may also be used for greater distances Figure 1 1 TIENet 306 with TIENet connector t and TIENet with wire connector b 1 1 TIENet 306 Sampler Interface Section 1 Introduction 1 1 Operation The Signature flow meter uses a 5 Volt pulse output to signal a connected Teledyne Isco automatic sampler to collect flow paced samples Based on user defined conditions the flow meter can signal the sampler to start enable or stop disable It also receives signals from the sampler indicating when a sample is collected event mark and into which bottle the sample is dis tributed bottle number s 5 A sample TIENet 306 Device Signature Flow Meter Isco Wastewater Sampler Model 6712 Portable Sampler Shown Figure 1 2 Basic 306 Configuration TIENet 306 Sampler Interface Section 1 Introduction 1 2 Connector The 306 connects to the flow meter port of a Teledyne Isco Description sampler with a 6 pin female sealed plug The Isco 4700 and 5800 Refrigerated sampler also requires the adaptor cable that duplicates the Isco sampler flow meter port Figure 1 3 306 Sealed connector The function of each pin in the figure above is listed in Table 1 1 Table 1 1 306 Connector Pin Functions 12VDC sampler detecti2. 0 CONTACT RS485 RAIN OU 3 Figure 2 5 Position and secure the cable 2 1 2 Connecting to The optional external TIENet devices compatible with the Sig Signature Portablevia nature Portable and Signature all scan into the hardware in the a TIENet Receptacle same manner A scan is required anytime a new TIENet device is added Multiple TIENet devices can be connected simultaneously to the same Signature Portable Flow Meter The following TIENet devices will attach to the TIENet receptacle e Ultrasonic Level Sensor e Area Velocity Sensor 2 4 TIENet 306 Sampler Interface Section 2 Installation and Operation 301 pH Interface e LaserFlow e 306 Sampler Interface Connecting a TIENet plug To connect the TIENet plug from the sensor to the TIENet Recep to the Signature Portable tacle 1 Align the connectors and push together Figure 2 6 2 The sensor release will click when the sensor connector is fully seated 3 Connect the two caps together 4 After the physical connection is made a scan must be per formed for the device to be recognized For additional TIENet connections use the TIENet Y cable or alternately an Expansion Box O Ring and Lubrication 1 Coat the O ring s sealing surface with a silicone lubricant for the TIENet receptacle CAUTION Do not use petroleum based lubricants Petroleum based lubricants will cause the O ring to swell and eventually deterio rate Aerosol silicon
3. 0 0 0 x DC Motor BEX O O X O O O Connectors EA X X 0 0 0 Battery BRR X O O O O X Solenoid valve FRFFEHEYNARTA NEMKEE Name and amount of Hazardous Substances or Elements in the product O 3 1 33 5535 SDE MA 45 MAA E BYES MEMENRERRUT O Represent the concentration of the hazardous substance in this component s any homogeneous pieces is lower than the ST standard limitation RRBABSRSWRELEBZRAHR HQRAA PHASES MENENRERR AL TEHA RESIDAN LE RATO AERA ETT HE DA X Represent the concentration of the hazardous substance in this component s at least one homogeneous piece is higher than the ST standard limitation Manufacturer may give technical reasons to the X marks yg REA AB The Environmentally Friendly Use Period EFUP was determined through experience E RAR DAA GDA MEAFAR MR 2007 F EAN TFERRAR AAA BATA The date of Manufacture is in code within the serial number The first three numbers are the year of manufacture 207 is year 2007 followed by a letter for the month A is January B is February and so on Hazmat Table Signature Meter Sensors and Accessories 60 4302 091 Rev A Teledyne Isco One Year Limited Factory Service Warranty This warranty exclusively covers Teledyne 0 instruments providing a one year limited warranty covering parts and labor Any instrument that fails during the warranty period due to faulty parts or workmanship will be repair
4. 6 5m 5800 4700 OLNY uu224022000220snnseensnssnnesnnnesnnnnsnnennensnensn ern 60 5804 178 Assembly Model 306 10m 5800 4700 OLNY escescessscesseesseeeeseessneeseecesaeccsaecaeeeaeseneeenes 60 5804 179 Assembly Model 306 23m 5800 4700 OLNY escessecsscesseeeeeceeseeeseeesecesaeecsaecsaeecaaeseneeeaes 60 5804 180 306 Sampler Interface cable with signature connection ending in TIENet plug For use with portable Signature TIENet receptacle 06 60 4304 078 10 1m 32 8SHt cable usarlas 60 4304 076 23 0 CADIS is 60 4304 077 CA Assembly TIENet Y w 9 60 4304 066 TIENet expansion box includes 10 ft TIENet cable and 2 cord 110 60 4307 023 Cord grip fitting 3 4 NPT for TIENet cable una anne 209 0073 12 Bulk TIENet Cable cut to length order by the foot ccccoococononooocccnnnnonancnnncnannnnncccnnnnoss 60 4304 050 4700 5800 Sampler Interface cable ooonooocccnnonococcnnnononoccnnnnnnonnnnoncnnnnnnncnonnnnnnnncnn cnn ncnnnnnons 60 5314 697 M Note Teledyne Isco uses FreeRTOS version 5 4 2 in its TIENet devices In accordance with the FreeRTOS license FreeRTOS source code is available on request For more information visit www FreeRTOS org TIENet 306 Sampler Interface Section 2 Installation and Operation 2 1 Installation External TIENet devices such as the 306 are all connected to the Signature Flow Meter in the same manner usually using conduit or cord grip cable fittin
5. TIENet 306 Sampler Interface Installation and Operation Guide ISCO m Sampler Interface TIENet KN TELEDYNE ISCO Everywhereyoulook Manual Body 69 4303 072 opyri right 2012 All rights reserved Teledyne Isco evision D April 2015 Foreword This instruction manual is designed to help you gain a thorough understanding of the operation of the equipment Teledyne Isco recommends that you read this manual completely before placing the equipment in service Although Teledyne Isco designs reliability into all equipment there is always the possibility of a malfunction This manual may help in diagnosing and repairing the malfunction If a problem persists call or e mail Teledyne Isco technical support for assistance Simple difficul ties can often be diagnosed over the phone For faster service please have your serial number ready If it is necessary to return the equipment to the factory for service please follow the shipping instructions provided by technical support including the use of the Return Merchandise Authori zation RMA specified Be sure to include a note describing the malfunction This will aid in the prompt repair and return of the equipment Teledyne Isco welcomes suggestions that would improve the information presented in this manual or enhance the operation of the equipment itself Teledyne Isco is continually improving its products and reserves the right to change product s
6. afety alerts These three levels are described in the sample alerts below CAUTION Cautions identify a potential hazard which if not avoided may result in minor or moderate injury This category can also warn you of unsafe practices or conditions that may cause property damage WARNING Warnings identify a potentially hazardous condition which if not avoided could result in death or serious injury DANGER DANGER limited to the most extreme situations to identify an imminent hazard which if not avoided will result in death or serious injury TIENet 306 Sampler Interface Safety Hazard Symbols Warnings and Cautions The equipment and this manual use symbols used to warn of hazards The symbols are explained below Hazard Symbols The exclamation point within the triangle is a warning sign alerting you of important instructions in the instrument s technical reference manual The lightning flash and arrowhead within the triangle is a warning sign alert ing you of dangerous voltage inside the product Symboles de s curit Ce symbole signale l existence d instructions importantes relatives au produit dans ce manuel Ce symbole signale la pr sence d un danger d lectocution Warnungen und Vorsichtshinweise Das Ausrufezeichen in Dreieck ist ein Warnzeichen das Sie darauf aufmerksam macht daB wichtige Anleitungen zu diesem Handbuch geh ren Advertencias y Pre
7. aking care not to strain any wire connections Gently tug each wire when finished to verify secure connection to the screw terminals M Note 2 2 The SHIELD wire is the bare drain emerging from the foil shield around the YELLOW and BROWN wires The BRAID DRAIN wire is the bare drain emerging from the sur rounding braided shield inside the cable jacket It is not neces sary to prevent the two braids from coming into contact with each other TIENet 306 Sampler Interface Section 2 Installation and Operation Shield N YELLOW BROWN Braid Drain SHIELD BRAID DRAIN O 9 O Figure 2 3 TIENet Device terminal connections 5 Press the terminal strip back down into its socket on the case board as shown in Figure 2 5 taking care not to strain any wire connections Figure 2 4 Attach wired terminal strip to case board socket 6 Gently tug the cable downward to remove any slack within the enclosure taking care not to put any stress on the con nection 7 Tighten the cord grip sealing nut A CAUTION If you are using conduit instead of the cord grip fitting the con duit must be sealed to prevent harmful gases and moisture 2 3 TIENet 306 Sampler Interface Section 2 Installation and Operation from entering the Signature enclosure Failure to seal conduit could reduce equipment life 8 Close the front panel and fasten it shut with the two Phil lips screws M4 MODBU Y 3
8. cauciones Der gepfeilte Blitz im Dreieck ist ein Warnzeichen das Sei vor gef hrlichen Spannungen im Inneren des Produkts warnt Esta se al le advierte sobre la importancia de las instrucciones del manual que acompa an a este producto Esta se al alerta sobre la presencia de alto voltaje en el interior del producto TIENet 306 Sampler Interface Table of Contents Section 1 Introduction Ti Operation sc Art Pre dk as Meet hacen otk ah eee wet le 1 2 1 2 Connector Description 0 0 cece eee nee nen 1 3 1 3 Technical Specifications 0 000 een eee eee 1 3 1 4 Accessories rs ne er lan PAE Ei ge lee Bees 1 4 Section 2 Installation and Operation 2 1 Installation 2 2 50 yee ar na ne ee nn ran a 2 1 2 1 1 Connecting to the Flow Meter 2 2222 0 cece cee eens 2 1 2 1 2 Connecting to Signature Portable via a TIENet Receptacle 2 4 2 1 3 Connecting to the Sampler 0 0 ccc cece eens 2 6 2 2 Configuring the Interface 20222222 e ene e eae 2 6 2 2 1 Updating the Device List 202222 eens 2 6 2 2 2 Input Data from the Sampler 0 0 eens 2 6 2 3 Enabling and Pacing the Sampler 0 0 cc cee cee eens 2 9 2 3 1 Enable Settings iia a a a ee ad een 2 9 2 3 2 Sampler Pacing anar dara ne bed cheat 2 9 2 4 Firmware Updates tt ner re 2 11 2 5 Contact Teledyne Isco 1 1 eee 2 11 App
9. cent table to determine the part number for the item Replacement parts can be purchased by contacting Teledyne Isco s Customer Service Department Teledyne Isco Customer Service Department P O Box 82531 Lincoln NE 68501 USA Phone 800 228 4373 402 464 0231 FAX 402 465 3022 E mail IscoInfo teledyne com A 1 TIENet 306 Sampler Interface A 1 1 306 Sampler Interface A 2 TIENet 306 Sampler Interface REPLACEMENT PARTS LIST SHEET 2 OF 2 TELEDYNE ISCO REV i PART NUMBER DESCRIPTION 202100669 O RING 669 ID 079 CROSS SECTION 2 202106016 O RING 614 ID 070 CROSS SECTION 3 231310140 SCREW 4 SELF TAPPING TYPE B 4 602003015 CAP MALE PROBE 5 604303068 PLUG SAMPLER INTERFACE NOTE For current prices and quotations on parts contact Teledyne Isco Service Department 2 This list is subject to change without notice A 3 TIENet 306 Sampler Interface A 4 mt 45 5 43 MAA TANIA MMS Name and amount of Hazardous Substances or Elements in the product HERE UM A 03 RE Rp Hazardous Substances or Elements Component Name 45 ul 8 SEHR SROKA Pb Hg Cd Cr VD PBB PBDE ye RER X O O O O O Circuit Boards SEAN X O O O O O Display 5 0 0 0 0 0 X Wiring Ys ARB O O O O O X Internal Cables ss BAIL x 0
10. e lubricant sprays often use petro leum based propellents If you are using an aerosol spray allow a few minutes for the propellent to evaporate before pro ceeding 2 The sensor release will click when the sensor connector is fully seated 3 Connect the two caps together Figure 2 6 How to connect a TIENet plug to the Signature Portable 2 5 TIENet 306 Sampler Interface Section 2 Installation and Operation 2 1 3 Connecting to the Connect the sealed end of the cable to the flow meter port of the Sampler sampler M Note The sampler must have its own power source CALA 6712 Controller Shown Figure 2 7 Connecting to the sampler 2 2 Configuring the To configure the Signature flow meter for operation with a Interface sampler using the TIENet 306 device press MENU dB to access the top menu and select Hardware Setup For all TIENet devices including the 306 select TIENet Setup Smart Sensor 2 2 1 Updating the Device When the 306 is physically added to the system select Perform List Scan so that the flow meter detects it When the scan is complete the 306 appears in the list of connected devices ready to be con figured with the steps shown in Figure 2 9 on the following page M Note From the Hardware Setup menu Configure refers to defining and selecting the parameters for each connected device 2 2 2 Input Data from the The two parameters that appear for the 306 device are Samp
11. ed at the factory at no charge to the customer Teledyne Isco s exclusive liability is limited to repair or replacement of defective instruments Teledyne Isco is not liable for consequential damages Teledyne Isco will pay surface transportation charges both ways within the 48 contiguous United States if the instrument proves to be defective within 30 days of shipment Throughout the remainder of the warranty period the customer will pay to return the instrument to Teledyne Isco and Teledyne Isco will pay surface transportation to return the repaired instrument to the customer Teledyne Isco will not pay air freight or customer s packing and crating charges This warranty does not cover loss damage or defects resulting from transportation between the customer s facility and the repair facility The warranty for any instrument is the one in effect on date of shipment The warranty period begins on the shipping date unless Teledyne Isco agrees in writing to a different date Excluded from this warranty are normal wear expendable items such as pH sensors charts ribbon lamps tubing and glassware fittings and wetted parts of valves and damage due to corrosion misuse accident or lack of proper maintenance This warranty does not cover products not sold under the Teledyne Isco trademark or for which any other warranty is specifically stated No item may be returned for warranty service without a return authorization number issu
12. ed by Teledyne Isco This warranty is expressly in lieu of all other warranties and obligations and Teledyne Isco specifically disclaims any warranty of merchantability or fitness for a particular purpose The warrantor is Teledyne Isco 4700 Superior Lincoln NE 68504 U S A This warranty applies to the USA and countries where Teledyne Isco does not have an authorized dealer Customers in countries outside the USA where Teledyne Isco has an authorized dealer should contact their Teledyne Isco dealer for warranty service Before returning any instrument for repair please call fax or e mail the Teledyne Isco Service Department for instructions Many problems can often be diagnosed and corrected over the phone or by e mail without returning the instrument to the factory Instruments needing factory repair should be packed carefully and shipped to the attention of the service department Small non fragile items can be sent by insured parcel post PLEASE BE SURE TO ENCLOSE A NOTE EXPLAINING THE PROBLEM Shipping Address Teledyne Isco Attention Repair Service 4700 Superior Street Lincoln NE 68504 USA Mailing Address Teledyne Isco PO Box 82531 Lincoln NE 68501 USA 800 775 2965 lab instruments 866 298 6174 samplers amp flow meters Sales amp General Information 800 228 4373 USA amp Canada Phone Repair service Fax 402 465 3001 Email October 11 2013 P N 60 1002 040 Rev H IscoSer
13. endix A Replacement Parts A 1 Replacement Parts 0 0 cece A 1 A 1 1 306 Sampler Interface 0 0 cece eee ences A 2 List of Figures 1 1 TIENet 306 with TIENet connector t and TIENet with wire connector b 1 1 1 2 Basic 306 Configuration 0 00 cet een eens 1 2 1 3 306 Sealed connector 0 cece ec 1 3 2 1 TIENet Device terminal strips 0 0 cece eee eee 2 1 2 2 Installing cable with a cord grip fitting 0 2 2 2 3 TIENet Device terminal connections 0 0 0 c cece eee 2 3 2 4 Attach wired terminal strip to case board socket 0 2 3 2 5 Position and secure the 68216 2202 een nes 2 4 2 6 How to connect a TIENet plug to the Signature Portable 2 5 2 7 Connecting to the sampler 0 0 cette eens 2 6 2 8 Character grid ons a san aa 2 7 2 9 Menu Tree 306 Configuration 0 00 en 2 8 2 10 Sampler enabling and pacing 0 ccc tte eee 2 10 TIENet 306 Sampler Interface Table of Contents vi TIENet 306 Sampler Interface Section 1 Introduction The TIENet Model 306 Sampler Interface connects the Sig nature Flow Meter to a Teledyne Isco wastewater sampler Through this connection the Signature can enable the sampler based on user specified conditions pace the sampling routine based on flow and receive sample and bottle information from the sampler The 306 is available with a
14. er reaches the end of its program or the latch is reset by the flow meter When the sampler setup screen first appears the Reset Latch function is highlighted by default If you do not want to reset the latch be sure this field is NOT highlighted before pressing Enter or Next Enable on Trigger The sampler becomes enabled when trig gered by a defined condition selected from the pull down list Once the condition has passed the sampler is once more dis abled M Note In order to populate the pull down list you must first define one or more conditions Refer to your Signature Installation and Operation Guide for detailed instructions on defining con ditions and using them to build equations For flow paced sampling select Pace by Flow If the sampler is programmed for time paced sampling select Pace None Highlight the Volume Input field to select the Total Flow mea surement used to pace the sampler Next to Pace Interval select volumetric units of measure and enter the number of units such as gallons equal to one flow pulse TIENet 306 Sampler Interface Section 2 Installation and Operation Configure Options 5 Data Storage Push Setup 1 Site Setup 2 Measurement Setup 3 Adjust 4 Equation Trigger Setup 306 lt serial number gt Sampler Interface Sampler Setup 1 306 lt serial number gt Sampler Interface 6 Sampler Setup 7 Inputs Outputs Alarms Setup 8 Reset Totalizers 9 Repor
15. gs Multiple external TIENet devices can be connected simultaneously 2 1 1 ConnectingtotheFlow Refer to your Signature Flow Meter manual for instructions on Meter accessing the instrument s interior components WARNING Before proceeding ensure that the flow meter has been disconnected from mains power M Note The steps that follow include instructions for installing cord grip fittings Some applications will use user supplied 4 ID con duit for cable routing 1 Remove one of the 6 position plug in terminal strip connec tors from the case board YELLOW BROWN SHIELD Figure 2 1 TIENet Device terminal strips 2 If using a cord grip fitting install the cable nut in the appropriate opening on the bottom of the Signature enclo sure securing it to the wall with the lock nut concave side facing wall 2 1 TIENet 306 Sampler Interface Section 2 Installation and Operation Lock Nut concave side facing wall pa Seal Cable Nut 3 Feed the TIENet device cable end through the sealing nut and seal and through the cable nut Lightly tighten the sealing nut just enough to hold the cable in place while installing the connector Sealing Nut color may vary Figure 2 2 Installing cable with a cord grip fitting 4 Attach the wire ends to the terminal strip as shown in Figure 2 3 then press the terminal strip back down into its socket on the case board as shown in Figure 2 4 t
16. ler 306 Sample Bottle Sample event and Bottle number 306 Input Voltage 12VDC present on pin A from the sampler connector the sampler is powered separately from the Sig nature flow meter NOTE This measurement is only to indicate whether or not a sampler is connected 2 6 TIENet 306 Sampler Interface Section 2 Installation and Operation The name of any parameter can be customized by highlighting it and pressing Enter Pa to display the character grid Nav igate the grid using the arrow keys Select characters with Enter and clear characters with Delete LaS 1306 Sample Bottle Figure 2 8 Character grid 2 7 TIENet 306 Sampler Interface Section 2 Installation and Operation Select Operation 1 Hardware Setup 2 Configure 3 Administration 4 Home Hardware Setup 1 Smart Sensor Setup TIENet 2 SDI 12 Setup 3 MODBUS Input Setup 4 MODBUS Output Setup 5 Modem Setup With initial connection begin by performing a hardware scan to add the 306 TIENet Setup Smart Sensor Perform Scan e Configure Measurements Configure Measurements 1 XXX Press Enter for a list of sensors Scroll with XXX Parameter XXX Parameter arrow keys to the 306 and press Enter to select oO XXX Parameter Configure Measurements Scroll with arrow keys to highlight select any dis played parameter El 306 Sample Bottle 306 Inp
17. on Ground Flow Pulse Out Bottle Number In Event Mark In Enable Out 1 3 Technical Specifications Table 1 2 Technical Specifications Functions Output Teledyne Isco Sampler Flow pacing Enabling on trigger Input Event and bottle number Power From Signature Flow Meter Operating Temperature 4 to 122 F 20 to 50 C Storage Temperature 40 to 140 F 40 to 60 C Pulse Width 50 ms Pulse Output 5 volts Sampler Connection Teledyne Isco Models 6712 Avalanche Gla cier GLS and 3700 Series Standard 6 Pin MS connector 4700 amp 5800 Flow meter port adaptor cable a All specifications are subject to change without notice 1 3 TIENet 306 Sampler Interface Section 1 Introduction 1 4 Accessories Accessories can be purchased by contacting Teledyne Isco s Cus tomer Service Department Teledyne Isco Customer Service Dept P O Box 82531 Lincoln NE 68501 USA Phone 800 228 4373 402 464 0231 FAX 402 465 3022 E mail IscoInfo teledyne com M Note For replacement parts please see Appendix A 1 Replacement Parts 306 Sampler Interface cables with Signature connection ending in unterminated leads For use with 6 position plug in green terminal strip cord grip included Cut to length cablE aii ernennen mean AE a aa datan 60 4304 088 10 82 8 ft cable 60 4304 007 23 10 1010 cable a re 0 A 60 4304 008 Assembly Model 30
18. pecifications replacement parts schematics and instructions without notice Contact Information Customer Service Phone 800 228 4373 USA Canada Mexico 402 464 0231 Outside North America Fax 402 465 3022 Email IscoCSR teledyne com Technical Support Phone Toll Free 866 298 6174 Samplers Flow Meters and Multi parameter Probes Toll Free 800 775 2965 Syringe Pumps and Liquid Chromatography Email IscoService teledyne com Return equipment to 4700 Superior Street Lincoln NE 68504 1398 Other Correspondence Mail to P O Box 82531 Lincoln NE 68501 2531 Email Iscolnfo teledyne com Revised April 2014 General Warnings Hazard Severity Levels TIENet 306 Sampler Interface Safety Before installing operating or maintaining this equipment it is imperative that all hazards and preventive measures are fully understood While specific hazards may vary according to location and application take heed of the following general warnings WARNING Avoid hazardous practices If you use this instrument in any way not specified in this manual the protection provided by the instrument may be impaired AVERTISSEMENT Eviter les usages p rilleux Si vous utilisez cet instrument d une mani re autre que celles qui sont specifi es dans ce manuel la protection fournie de l instrument peut tre affaiblie cela augmentera votre risque de blessure This manual applies Hazard Severity Levels to the s
19. ts History Setup NA Be sure this field is only highlighted if you want to reset the latch Enable Never Enable Always Enable Latched Enable on Trigger Trigger Name Pace None Volume Pace by Flow Input Total Flow Pace Interval Enter amount of volume equal to one flow pulse Figure 2 10 Sampler enabling and pacing 2 10 Select condition from list Condition s must be defined in order to appear in list 0 gallons i _ 4 Select volumetric units of measure 2 4 Firmware Updates 2 5 Contact Teledyne Isco TIENet 306 Sampler Interface Section 2 Installation and Operation The TIENet device s firmware is updated via the USB port on the front panel of the Signature Flow Meter Step by step instruc tions for updating the firmware can be found in Section 2 of the Signature user manual If you have further questions about the installation operation and maintenance of your TIENet device please contact our service department at Teledyne Isco 4700 Superior St Lincoln NE 68504 Phone 866 298 6174 or 402 464 0231 Fax 402 465 3022 E mail IscoService teledyne com TIENet 306 Sampler Interface Section 2 Installation and Operation 2 12 TIENet 306 Sampler Interface Appendix A Replacement Parts A 1 Replacement Parts Replacement parts are called out in the following illustrations Refer to the call out in the adja
20. ut Voltage or parameter name Press NEXT to confirm configuration There may be a slight delay TIENet Configuration The sensors are being TIENet Setup Smart Sensor The sensors have been configured configured Please wait Figure 2 9 Menu Tree 306 Configuration 2 8 2 3 Enabling and Pacing the Sampler 2 3 1 Enable Settings 2 3 2 Sampler Pacing TIENet 306 Sampler Interface Section 2 Installation and Operation The Signature flow meter can enable or disable the connected sampler with a signal based on a defined condition such as level flow rate pH temperature etc or combination of conditions This is called a sampler Trigger Refer to your Signature Installation and Operation Guide for detailed instructions on defining conditions and using them to build equations If the sampler is disabled at its programmed start time the sam pling program is suspended until the sampler is enabled Refer to your sampler s user manual for detailed instructions on sampler programming To set up the sampler control select option 6 Sampler from the Configure menu refer to Figure 2 10 on the following page The sampler setup screen has a choice of four enable settings Enable Never The sampler remains disabled and is never activated Enable Always The sampler remains enabled and is never deactivated Enable Latched Once enabled the sampler remains enabled until it eith
21. vice teledyne com a TELEDYNE ISCO Everywhereyoulook
Download Pdf Manuals
Related Search