User`s manual - Vt.vtp
Contents
1. All system handsets show Out of range OR no power at base for a few seconds and then you hear a confirmation tone from the handset When the phone successfully enters the CEC battery charging testing mode all handsets show Press HOLD on base for 4 sec then press on handset When the phone fails to enter this mode repeat all the steps mentioned above To deactivate the CEC battery charging testing mode 1 Unplug the telephone base power adapter from the power outlet then plug it back in The telephone base is powered up as normal 2 Register your handsets back to the telephone base See page 11 for handset registration instructions 33 Appendix Limited warranty The AT amp T brand is used under license any repair replacement or warranty service and all questions about this product should be directed to our website at www telephones att com or cat 1 800 222 3111 in canada dial 1 866 288 4268 1 What does this limited warranty cover The manufacturer of this AT amp T branded product warrants to the holder of a valid proof of purchase CONSUMER or you that the product and all accessories provided in the sales package PRODUCT are free from defects in material and workmanship pursuant to the following terms and conditions when installed and used normally and in accordance with the PRODUCT operating instructions This limited warranty extends only to the CONSUMER for products purchased and us2. Charger installation Install the charger as shown below Plug the power adapter into an electrical outlet not controlled by a wall switch IMPORTANT INFORMATION 1 Use only the power adapter supplied with this product To order a replacement power adapter visit our website at www telephones att com or call 1 800 222 3111 in canada dial 1 866 288 4268 2 The power adapter is intended to be correctly oriented in a vertical or floor mount position The prongs are not designed to hold the plug in place if it is plugged into a ceiling under the table or cabinet outlet Getting started Battery installation and charging Install the battery as shown below Step 1 Plug the battery connector securely into the socket inside the handset battery compartment matching the color coded label Insert the supplied battery with the label THIS SIDE UP facing up as indicated Step 2 Align the cover flat against the battery compartment then slide it upwards until it clicks into place Step 3 CHARGE light Charge the handset by placing it face up in the charger The CHARGE light is on when charging Getting started Battery installation and charging After you install your telephone or power returns following a power outage the handset will prompt you to set the date and time To skip setting the date and time press OFF CLEAR To replace the battery press the tab and slide the battery compartment cove
3. e During deregistration all cordless handset s and DECT 6 0 cordless headset s will also be deregistered 12 Appendix Troubleshooting If you have difficulty with your phone please try the following suggestions For Customer Service visit our website at www telephones att com or call 1 800 222 3111 In Canada dial 1 866 288 4268 My phone doesn t work at all Make sure the power cord is securely plugged in Make sure you plug the battery connector securely into the cordless handset Make sure you plug the telephone line cord securely and firmly into the telephone base and the telephone wall jack Charge the battery in the cordless handset for at least 16 hours For optimum daily performance return the cordless handset to the telephone base or charger when not in use If the battery is depleted it might take approximately five minutes to charge the handset before it shows Low battery See page 8 for details Reset the telephone base Unplug the electrical power Wait for approximately 15 seconds then plug it back in Allow up to one minute for the cordless handset and telephone base to reset You may need to purchase a new battery Refer to Battery installation and charging pages 6 7 in this user s manual 13 Appendix Troubleshooting The display shows NO LINE I cannot get a dial tone e Try all the suggestions mentioned above e If the previous suggestions do not work disconnect the telephone l
4. word mark and logos are owned by Bluetooth SIG Inc and any use of such marks by Advanced American Telephones and its parent VTech Holdings Limited is under license VTech Holdings Limited is a member of Bluetooth SIG Inc Other trademarks and trade names are those of their respective owners 2010 2015 Advanced American Telephones All Rights Reserved AT amp T and the AT amp T logo are trademarks of AT amp T Intellectual Property licensed to Advanced American Telephones San Antonio TX 78219 Printed in China Parts checklist Your telephone package contains the following items Save your sales receipt and original packaging in the event warranty service is necessary User s manual TL86009 DECT 6 0 expansion handset for use with AT amp T model 7186109 corded cordiess telephone answering system with BLUETOOTH wireless technology User s manual Cordless handset Charger for cordless handset with power adapter installed Battery for Battery Belt clip for cordless handset compartment cordless handset cover User s manual TL86009 DECT 6 0 expansion handset for use with AT amp T model TL86109 corded cordless telephone answering system with BLUETOOTH wireless technology Table of contents Getting started Installations 1 Quick reference guide 2 Charger installation 5 Battery installation and charging 0 eeseecseecsesceteseesseeceeeeterseens 6 Battery Chargi
5. and the construction of your home or office Extended range and clarity This telephone base comes with an antenna which gives much better clarity and covers a longer range than before 38 www telephones att com The Bluetooth word mark and logos are owned by Bluetooth SIG Inc and any use of such marks by Advanced American Telephones and its parent VTech Holdings Limited is under license VTech Holdings Limited is a member of Bluetooth SIG Inc Other trademarks and trade names are those of their respective owners 2010 2015 Advanced American Telephones All Rights Reserved AT amp T and the AT amp T logo are trademarks of AT amp T Intellectual Property licensed to Advanced American Telephones San Antonio TX 78219 RBRC and 1 800 8 BATTERY are registered trademarks of the Rechargeable Battery Recycling Corporation Printed in China Issue 7 0 AT amp T 05 15
6. exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you Please retain your original sales receipt as proof of purchase 36 Appendix Technical specifications RF frequency band 1921 536MHz 1928 448MHz Channels 5 Operating temperature 32 F 122 F 0 C 50 C Handset voltage 2 4 3 2 VDC Charger voltage 6VDC 400mA DC adapter output Replacement battery 2 4V 750mAH Operating times Talk time handset up to seven hours Talk time speakerphone up to five hours Standby up to seven days Operating times vary depending on your actual use and the age of the battery DECT 6 0 digital technology The AT amp T DECT 6 0 products offer unsurpassed range performance and sound clarity This is achieved through a unique antenna design and advances in noise filtering technology An independent laboratory has confirmed that AT amp T DECT 6 0 products perform up to 45 better in range competitions Now calls can be taken in the basement backyard and garage with exceptional sound quality 37 Appendix Technical specifications Telephone operating range This cordless telephone operates within the maximum power allowed by the Federal Communications Commission FCC Even so this handset and telephone base can communicate over a certain distance which can vary with the locations of the telephone base and handset the weather
7. in Allow up to one minute for the cordless handset and telephone base to reset Other electronic products such as HAM radios and other DECT phones can cause interference with your cordless phone Try installing your phone as far away as possible from these types of electronic devices The batteries do not hold a charge If the cordless handset is in the charger and the charge light does not come on refer to The charge light is off page 21 in this Troubleshooting guide Charge the battery in the cordless handset for at least 16 hours For optimum daily performance return the cordless handset to the charger when not in use If the battery is depleted it may take approximately five minutes to charge the handset before it shows Low battery See page 8 for details You may need to purchase a new battery Please refer to Battery installation and charging pages 6 7 in this user s manual 16 Appendix Troubleshooting I get noise static or a weak signal even when I m near the telephone base If you subscribe to high speed Internet service DSL digital subscriber line through your telephone lines you must install a DSL filter between each telephone line cord and telephone wall jack The filter prevents noise and caller ID problems caused by DSL interference Please contact your DSL service provider for more information about DSL filters You may be able to improve the performance of your cordless phone by installing
8. minutes The screen shows Battery has enough Charge without interruption Low battery and charge to be used for a until the screen shows flashes short time HANDSET X at least 25 minutes The screen shows Battery is charged To keep the battery HANDSET X charged place it in the telephone base or charger when not in use Q NOTE If you are on a phone call in low battery mode you hear four short beeps every minute Getting started Belt clip amp optional headset gt To remove the belt clip Gently lift either of the belt clip tabs shown in the figure outwards to remove the belt clip from the handset To attach the belt clip Snap the belt clip into the slots on both sides of the handset as shown in the figure For handsfree telephone conversations you can use any industry standard 2 5 mm headset purchased separately For best results use an AT amp T 2 5 mm headset To purchase a headset visit our website www telephones att com or call 1 800 222 3111 In Canada dial 1 866 288 4268 Lift the plastic Plug a 2 5 mm headset cover here into the jack on the side of handset beneath the small plastic cover Side of handset Adding handset to your telephone base Adding and registering handsets Before using a new TL86009 handset you must register it with the AT amp T TL86109 telephone system purchased separately The AT amp T TL86109 telephone system can accommodate
9. of electronic devices Do not install this phone near a microwave oven or on the same electrical outlet You may experience decreased performance while the microwave oven is operating If you plug your phone in with a modem or surge protector plug the phone or modem surge protector into a different location If this doesn t solve the problem relocate your phone or modem farther apart from one another or use a different surge protector Relocate your telephone base to a higher location The phone may have better reception when installed in a high area If other phones in your home are having the same problem the problem is in your wiring or telephone service Contact your telephone service provider charges may apply Excessive background noise will cause a speakerphone to fade in and out Try controlling the background noise by turning off any audio devices near the speakerphone Also try to avoid interrupting the person at the other end of the conversation while they are speaking If background noise cannot be controlled you should stop speakerphone operation and return to normal handset mode When using a speakerphone controlling background noise in your environment is essential While you are listening to your party press the MUTE softkey to temporarily turn your microphone off When it is your turn to speak remember to press the MUTE softkey to turn the microphone on 20 Appendix Troubleshooting The charge ligh
10. outlined under the Limited warranty If this equipment is causing harm to the telephone network the telephone service provider may temporarily discontinue your telephone service The telephone service provider is required to notify you before interrupting service If advance notice is not practical you will be notified as soon as possible You will be given the opportunity to correct the problem and the telephone service provider is required to inform you of your right to file a complaint with the FCC Your telephone service provider may make changes in its facilities equipment operation or procedures that could affect the proper functioning of this product The telephone service provider is required to notify you if such changes are planned 30 Appendix FCC Part 68 and ACTA If this product is equipped with a corded or cordless handset it is hearing aid compatible If this product has memory dialing locations you may choose to store emergency telephone numbers e g police fire medical in these locations If you do store or test emergency numbers please e Remain on the line and briefly explain the reason for the call before hanging up e Perform such activities in off peak hours such as early morning or late evening Industry Canada This device complies with Industry Canada license exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 th
11. outside motors microwave ovens refrigerators or fluorescent lighting e Excessive dust sources such as a workshop or garage e Excessive moisture e Extremely low temperature e Mechanical vibration or shock such as on top of a washing machine or workbench Getting started Quick reference quide Softkeys 2 Press to select a menu item displayed above the key CHARGE light blue ring around DIR A VOL W CID On when the handset is charging in the charger DIR A VOL Press to scroll up while in menus Press to increase the volume level during a call Press to show directory entries when the telephone is not in use While entering names or numbers press to move the cursor to the right x5 w8 CELL Press to make or answer a w0 cell call pane Flashes quickly when there WO amp is an incoming cell call Flashes slowly when a cell call is on hold Bluetooth OFF CLEAR While using menus press to cancel an operation back up to the previous menu or exit the menu display Press and hold to return to idle mode While entering names or numbers press to delete a digit or a character During a call press to hang up VOL W CID Press to scroll down while in menus Press to decrease the volume level during a call Press to show the caller ID history when the telephone is not in use While entering names or numbers press to move the cursor
12. pr s d une piscine d un bain d un vier de cuisine ou d une cuve de lavage N utilisez pas de liquides ou de vaporisateurs a rosol de nettoyage Si le produit entre en contact avec du liquide d branchez imm diatement le fil t l phonique ou le cordon d alimentation Ne rebranchez pas le produit avant qu il soit compl tement sec Installez cet appareil dans un endroit prot g o personne ne peut tr bucher sur les cordons d alimentation ou la ligne t l phonique Prot gez les c bles contre les dommages ou l abrasion Si Le produit ne fonctionne pas correctement consultez la section D pannage Troubleshooting des pages 13 22 de ce guide d utilisation Si vous ne pouvez pas r gler le probl me ou si le produit est endommag consultez la section Garantie limit e Limited warranty des pages 34 36 N ouvrez pas ce produit sauf tel qu indiqu dans le guide d utilisation L ouverture du produit ou le remontage inad quat pourrait vous exposer des tensions dangereuses ou autres dangers Remplacez les piles uniquement tel que d crit dans votre guide d utilisation pages 6 7 N incin rez pas et ne percez pas les piles elles contiennent des produits chimiques caustiques L adaptateur de courant est con u pour tre orient verticalement ou install sur le plancher Les broches ne sont pas con ues pour se maintenir en place si la fiche est branch e dans une prise de courant au plafond sous la table ou sous une armoi
13. to a working electrical outlet which is not controlled by a wall switch Calls cannot be made from the handset if the telephone base is unplugged switched off or if the electrical power is interrupted Potential TV interference Some cordless telephones operate at frequencies that may cause interference to TVs and VCRs To minimize or prevent such interference do not place the telephone base of the cordless telephone near or on top of a TV or VCR If interference is experienced moving the cordless telephone farther away from the TV or VCR will often reduce or eliminate the interference Rechargeable batteries This product contains nickel metal hydride rechargeable batteries Exercise care in handling batteries in order not to create a short circuit with conductive material such as rings bracelets and keys The battery or conductor may overheat and cause harm Observe proper polarity between the battery and the battery charger Nickel metal hydride rechargeable batteries Dispose of these batteries in a safe manner Do not burn or puncture Like other batteries of this type if burned or punctured they could release caustic material which could cause injury 25 Appendix Important safety information The RBRC Seal means that the manufacturer is voluntarily participating in an industry program to collect and recycle nickel metal hydride rechargeable batteries when taken out of service within the United States These batteries may be t
14. up to 12 handsets The handset provided with the TL86109 comes registered as HANDSET You can register up to 11 additional handsets to the telephone base and they will be assigned numbers in the order they are registered HANDSET 2 HANDSET 3 HANDSET 4 and so on Your first handset is then renamed as HANDSET 1 10 Adding handset to your telephone base Expand your telephone system Add and register a handset When first purchased each expansion handset shows Press HOLD on base for 4 sec then press on handset after a battery is installed Each handset should be charged without interruption for at least 25 minutes before registering to the telephone base For more details on battery charging see the table on page 8 To register a handset 1 Press and hold HOLD on the telephone base for about four seconds until it shows Registering Please wait Then release the button 2 Press pound key on the handset Its screen shows Registering handset and it takes up to 60 seconds to complete the registration The handset and telephone base show HANDSET X Registered X represents the handset number assigned and you hear a beep when the registration completes Onores e If the registration fails the handset shows Registration failed for a few seconds and then Press HOLD on base for 4 sec then press on handset Try the registration process again e You cannot register a handset if any other system handse
15. E Before calling for service please review the user s manual a check of the PRODUCT s controls and features may save you a service call Except as provided by applicable law you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the PRODUCT s to the service location The manufacturer will return repaired or replaced PRODUCT under this limited warranty to you Transportation delivery or handling charges are prepaid The manufacturer assumes no risk for damage or loss of the PRODUCT in transit If the PRODUCT failure is not covered by this limited warranty or proof of purchase does not meet the terms of this limited warranty the manufacturer will notify you and will request that you authorize the cost of repair prior to any further repair activity You must pay for the cost of repair and return shipping costs for the repair of products that are not covered by this limited warranty 35 Appendix Limited warranty 6 What must you return with the PRODUCT to get warranty service You must a Return the entire original package and contents including the PRODUCT to the service location along with a description of the malfunction or difficulty and b Include a valid proof of purchase sales receipt identifying the PRODUCT purchased PRODUCT model and the date of purchase or receipt and c Provide your name complete and correct maili
16. User s manual TL86009 DECT 6 0 expansion handset for use with AT amp T model TL86109 corded cordless telephone answering system with BLUETOOTH wireless technology Congratulations on your purchase of this AT amp T product Before using this AT amp T product please read Important safety information on pages 24 26 of this manual For complete instructions please refer to the manual provided with your TL86109 telephone For customer service or product information please visit our website at www telephones att com or call 1 800 222 3111 In Canada dial 1 866 288 4268 This telephone meets the California Energy Commission regulations for energy consumption Your telephone is set up to comply with the energy conserving standards right out of the box No further action is necessary Model number TL86009 Type DECT 6 0 expansion handset Serial number Purchase date Place of purchase Both the model and serial numbers of your AT amp T product can be found on the bottom of the telephone base Save your sales receipt and original packaging in case it is necessary to return your telephone for warranty service Telephones identified with this logo have reduced noise and RENE AUS interference when used with most T coil equipped hearing aids and SN cochlear implants The TIA 1083 Compliant Logo is a trademark of 9 the Telecommunications Industry Association Used under license a T TIA 1083 The Bluetooth
17. aken to a participating local retailer of replacement batteries or recycling center Or you may call 1 800 8 BATTERY for locations accepting spent Ni MH batteries RBRC and 1 800 8 BATTERY are registered trademarks of the Rechargeable Battery Recycling Corporation Precautions for users of implanted cardiac pacemakers Cardiac pacemakers applies only to digital cordless telephones Wireless Technology Research LLC WTR an independent research entity led a multidisciplinary evaluation of the interference between portable wireless telephones and implanted cardiac pacemakers Supported by the U S Food and Drug Administration WTR recommends to physicians that Pacemaker patients e Should keep wireless telephones at least six inches from the pacemaker e Should NOT place wireless telephones directly over the pacemaker such as in a breast pocket when it is turned ON e Should use the wireless telephone at the ear opposite the pacemaker WTR s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless telephones Especially about telephone answering systems Two way recording This unit does not sound warning beeps to inform the other party that the call is being recorded To ensure that you are in compliance with any federal or state regulations regarding recording a telephone call you should start the recording process and then inform the other party that you are recording the conve
18. burn or puncture batteries they contain caustic chemicals This power adapter is intended to be correctly oriented in a vertical or floor mount position The prongs are not designed to hold the plug in place if it is plugged into a ceiling or an under the table cabinet outlet 24 Appendix Important safety information CAUTIONS Use only the power adapter provided with this product To obtain a replacement visit our website at www telephones att com or call 1 800 222 3111 in canada diat 1 866 288 4268 Use only the supplied rechargeable battery or replacement battery model BT166342 BT266342 To order visit our website at www telephones att com or cau 1 800 222 3111 In Canada dial 1 866 288 4268 To prevent risk of fire or battery explosion replace with the correct battery type Dispose of used batteries according to the instructions Especially about cordless telephones Privacy The same features that make a cordless telephone convenient create some limitations Telephone calls are transmitted between the telephone base and the handset by radio waves so there is a possibility that your cordless telephone conversations could be intercepted by radio receiving equipment within range of the cordless handset For this reason you should not think of cordless telephone conversations as being as private as those on corded telephones Electrical power The telephone base of this cordless telephone must be connected
19. d by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Privacy of communications may not be ensured when using this telephone To ensure safety of users the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product This product has been tested and found to comply with the FCC criteria The handset may be safely held against the ear of the user The telephone base shall be installed and used such that parts of the user s body other than the hands are maintained at a distance of approximately 20 cm 8 inches or more This Class B digi
20. ed in the United States of America and Canada 2 What will be done if the PRODUCT is not free from defects in materials and workmanship during the limited warranty period materially defective PRODUCT During the limited warranty period the manufacturer s authorized service representative will repair or replace at the manufacturer s option without charge a materially defective PRODUCT If the manufacturer repairs the PRODUCT they may use new or refurbished replacement parts If the manufacturer chooses to replace the PRODUCT they may replace it with a new or refurbished PRODUCT of the same or similar design The manufacturer will retain defective parts modules or equipment Repair or replacement of the PRODUCT at the manufacturer s option is your exclusive remedy The manufacturer will return repaired or replacement products to you in working condition You should expect the repair or replacement to take approximately 30 days 3 How long is the limited warranty period The limited warranty period for the PRODUCT extends for ONE 1 YEAR from the date of purchase If the manufacturer repairs or replaces a materially defective PRODUCT under the terms of this limited warranty this limited warranty also applies to repaired or replacement PRODUCT for a period of either a 90 days from the date the repaired or replacement PRODUCT is shipped to you or b the time remaining on the original one year limited warranty whichever is long
21. er 34 Appendix Limited warranty 4 What is not covered by this limited warranty This limited warranty does not cover e PRODUCT that has been subjected to misuse accident shipping or other physical damage improper installation abnormal operation or handling neglect inundation fire water or other liquid intrusion or e PRODUCT that has been damaged due to repair alteration or modification by anyone other than an authorized service representative of the manufacturer or e PRODUCT to the extent that the problem experienced is caused by signal conditions network reliability or cable or antenna systems or e PRODUCT to the extent that the problem is caused by use with non AT amp T accessories or e PRODUCT whose warranty quality stickers PRODUCT serial number plates or electronic serial numbers have been removed altered or rendered illegible or e PRODUCT purchased used serviced or shipped for repair from outside the United States of America or Canada or used for commercial or institutional purposes including but not limited to products used for rental purposes or e PRODUCT returned without valid proof of purchase see item 6 or e Charges for installation or setup adjustment of customer controls and installation or repair of systems outside the unit 5 How do you get warranty service To obtain warranty service visit www telephones att com or call 1 800 222 3111 in canada dia 1 866 288 4268 NOT
22. ine cord from your telephone and connect the telephone line cord to another telephone e If there is no dial tone on that other telephone either your telephone line cord may be defective Install a new telephone line cord e If changing the telephone line cord does not help the wall jack or the wiring to this wall jack may be defective Try using a different wall jack in your home to connect your TL86109 telephone or contact your telephone service provider charges may apply I cannot dial out e Try all the suggestions mentioned above e Make sure you have a dial tone before dialing The cordless handset might take a second or two to find the telephone base and produce a dial tone This is normal Wait an extra second before dialing e Eliminate any background noise Noise from a television radio or other appliances might cause the phone to not dial out properly If you cannot eliminate the background noise try muting the cordless handset before dialing or dialing from another room with less background noise e If other phones in your home are having the same problem contact your telephone service provider charges might apply 14 Appendix Troubleshooting My cordless handset isn t performing normally Make sure you plug the power cord securely into the telephone base Plug the power adapter into a different working electrical outlet without a wall switch Move the cordless handset closer to the telephone base Y
23. is device must accept any interference received including interference that may cause undesired operation Privacy of communications may not be ensured when using this telephone The term IC before the certification registration number only signifies that the Industry Canada technical specifications were met The Ringer Equivalence Number REN for this terminal equipment is 1 0 The REN is an indication of the maximum number of devices allowed to be connected to a telephone interface The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices does not exceed five This product meets the applicable Industry Canada technical specifications 31 Appendix FCC Part 15 This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission FCC rules These requirements are intended to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determine
24. it is your turn to speak remember to press the MUTE softkey again to turn the microphone on Excessive background noise will cause a speakerphone to fade in and out Try controlling the background noise by turning off any audio devices near the speakerphone Also try to avoid interrupting the person at the other end of the conversation while they are speaking If background noise cannot be controlled you should terminate speakerphone operation and return to normal handset mode hear other calls while using my phone Disconnect the telephone base from the telephone jack and plug in a different telephone If you still hear other calls the problem is probably in your wiring or telephone service Call your telephone service provider While on a call or playing messages there is too much noise or the voice sounds tinny shrill or flat While on a call or playing messages press the EQ Ef button on the side of the handset until you find the settings that sounds the best 18 Appendix Troubleshooting My cordless handset does not ring when I receive a call Make sure that the ringer is not turned off Refer to Ringer volume on your user s manual Make sure the telephone line cord is plugged securely into the telephone base and the telephone jack Make sure the power cord is securely plugged in The cordless handset may be too far from the telephone base Charge the battery in the cordless handset for at least 16 hours F
25. mation Read and understand all instructions in the user s manual Observe all markings on the product Avoid using a telephone during a thunderstorm There may be a slight chance of electric shock from lightning Do not use a telephone in the vicinity of a gas leak If you suspect a gas leak report it immediately but use a telephone away from the area where gas is leaking If this product is a cordless model make sure the base is also away from the area Do not use this product near water or when you are wet For example do not use it in a wet basement or shower or next to a swimming pool bathtub kitchen sink or laundry tub Do not use liquids or aerosol sprays for cleaning If the product comes in contact with any liquid unplug any line or power cord immediately Do not plug the product back in until it has dried thoroughly Install this product in a protected location where no one can trip over any line or power cords Protect cords from damage or abrasion If this product does not operate normally see the Troubleshooting section on pages 13 22 of this user s manual If you cannot solve the problem or if the product is damaged refer to the Limited warranty section pages 34 36 Do not open this product except as directed in your user s manual Opening the product or reassembling it incorrectly may expose you to hazardous voltages or other risks Replace batteries only as described in your user s manual pages 6 7 Do not
26. mputer to establish connections and my telephone does not work e Make sure your computer is powered on e Make sure your Internet connection is working properly e Make sure that the software is installed and running for your nontraditional telephone service e Make sure to plug your USB telephone adapter into a dedicated USB port on your computer Do not plug into a multiple port USB hub USB splitter that is not powered e Ina few rare instances the USB port on your computer may not have enough power In these instances try using a USB hub with its own external power supply e If you are using a firewall it may prevent access to your nontraditional telephone service provider Contact your service provider for more information Common cure for electronic equipment If the telephone does not seem to be responding normally try putting the cordless handset in the charger If it does not fix the problem do the following in the order listed 1 Disconnect the power to the telephone base Disconnect the cordless handset battery Wait a few minutes Connect power to the telephone base oR WN Completely remove the battery Replace the battery and place the cordless handset into the telephone base or charger 6 Wait for the cordless handset to reestablish its connection with the telephone base Allow up to one minute for this to take place 22 Appendix Maintenance Taking care of your telephone e Your c
27. nelle La prise lectrique ne doit pas tre contr l e par un interrupteur mural Les appels ne peuvent pas tre effectu s partir du combin si la base n est pas branch e si elle est hors fonction ou si le courant lectrique est coup interf rences potentielles aux t l viseurs Certains t l phones sans fil fonctionnent sur des fr quences pouvant causer des interf rences aux t l viseurs et magn toscopes Pour r duire ou pr venir de tels parasites ne pas d poser la base du t l phone sans fil proximit d un t l viseur ou magn toscope ni directement sur celui ci Si votre t l viseur affiche des interf rences loignez le t l phone sans fil de celui ci afin de r duire les parasites Piles rechargeables Ce produit comporte des piles rechargeables l hydrure m tallique de nickel Usez de prudence lorsque vous manipulez de telles piles et veillez ne pas les court circuiter avec des mat riaux conducteurs tels que des bagues bracelets et cl s La pile ou le conducteur peut surchauffer et vous br ler Respectez la polarit ad quate entre les piles et le chargeur de piles Piles rechargeables l hydrure m tallique de nickel Jetez ces piles de mani re s curitaire N incin rez pas et ne peercez pas les piles Comme pour les autres piles du m me type si elles sont br l es ou perc es des mati res corrosives peuvent s en chapper ce qui risque de causer des br lures ou autres blessures cor
28. ng address and telephone number 7 Other limitations This warranty is the complete and exclusive agreement between you and the manufacturer of this AT amp T branded PRODUCT It supersedes all other written or oral communications related to this PRODUCT The manufacturer provides no other warranties for this PRODUCT The warranty exclusively describes all of the manufacturer s responsibilities regarding the PRODUCT There are no other express warranties No one is authorized to make modifications to this limited warranty and you should not rely on any such modification State Provincial Law rights This warranty gives you specific legal rights and you may also have other rights which vary from state to state or province to province Limitations Implied warranties including those of fitness for a particular purpose and merchantability an unwritten warranty that the PRODUCT is fit for ordinary use are limited to one year from date of purchase Some states provinces do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you In no event shall the manufacturer be liable for any indirect special incidental consequential or similar damages including but not limited to lost profits or revenue inability to use the PRODUCT or other associated equipment the cost of substitute equipment and claims by third parties resulting from the use of this PRODUCT Some states provinces do not allow the
29. ng imisi 8 Belt clip amp optional headset 9 Adding handset to your telephone base Adding and registering MANASEUS seen 10 Expand your telephone SY SCCM ss 11 Add and register a handset 11 Replace a handset 12 Appendix Troubleshooting sssesoeo00110000 13 Maintenance 23 Important safety information 24 Safety information 24 Especially about cordless telephones 25 Precautions for users of implanted cardiac pacemakers eeseeececceeseeeseeeneeees 26 Pacemaker patients 26 Especially about telephone answering systems 26 For C UL compliance n s 27 Mesures de s curit importantes xs 27 FCC Part 68 and ACTA 30 FCC Patt T9 32 California Energy Commission battery charging testing instructions Limited warranty Technical specifications 37 Getting started Installation You must install and See pages 6 8 charge the battery before for easy instructions using the telephone Your product may be shipped with a protective sticker covering the handset display remove it before use For customer service or product information visit our website at www telephones att com or call 1 800 222 3111 In Canada dial 1 866 288 4268 Avoid placing the telephone base too close to e Communication devices such as television sets VCRs or other cordless telephones e Excessive heat sources e Noise sources such as a window with traffic
30. nt PAS placer le t l phone sans fil directement sur le stimulateur cardiaque tel que dans une poche de chemise lorsque celui ci est en fonction e Ils doivent utiliser le t l phone sans fil en l appuyant sur l oreille qui se trouve dans la direction oppos e au stimulateur cardiaque L tude effectu e par l organisme WRS n a pas identifi de risque pour les d tenteurs de simulateurs cardiaques caus par les gens qui utilisent un t l phone sans fil proximit de ceux ci Sp cifiquement en rapport avec Les r pondeurs t l phoniques Enregistrement deux voies Cet appareil n met pas de bips d avertissement qui permettent de pr venir l autre partie que vous enregistrez la conversation Pour assurer votre conformit aux r glements f d raux ou provinciaux en rapport avec les enregistrements des conversations t l phoniques vous devriez informer l autre partie lorsque vous activez l enregistrement CONSERVEZ CES INSTRUCTIONS 29 Appendix FCC Part 68 and ACTA This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative Council for Terminal Attachments ACTA The label on the back or bottom of this equipment contains among other things a product identifier in the format US AAAEQ TXXXX This identifier must be provided to your telephone service provider upon request The plug and jack used to connect this equipment to premises wiring and the telephone netw
31. or optimum daily performance return the cordless handset to the charger when not in use You may have too many extension phones on your telephone line to allow all of them to ring simultaneously Try unplugging some of the other phones The layout of your home or office might be limiting the operating range Try moving the telephone base to another location preferably to a higher location If other phones in your home are having the same problem the problem is in your wiring or local service Contact your telephone service provider charges may apply Test a working phone at the phone jack If the other phone has the same problem the problem is the phone jack Contact your telephone service provider charges may apply Other electronic products such as HAM radios and other DECT phones can cause interference with your cordless phone Try installing your phone as far away as possible from these types of electronic devices Remove and install the battery again Wait for the cordless handset to reestablish its connection with the telephone base Allow up to one minute for this to take place Your line cord may be defective Try installing a new line cord 19 Appendix Troubleshooting My calls cut in and out while I m using my cordless handset Other electronic products such as HAM radios and other DECT phones can cause interference with your cordless phone Try installing your phone as far away as possible from these types
32. ordless telephone contains sophisticated electronic parts so you must treat it with care e Avoid rough treatment e Place the handset down gently e Save the original packing materials to protect your telephone if you ever need to ship it Avoid water e You can damage your telephone if it gets wet Do not use the handset in the rain or handle it with wet hands Do not install the telephone base near a sink bathtub or shower Electrical storms e Electrical storms can sometimes cause power surges harmful to electronic equipment For your own safety take caution when using electric appliances during storms Cleaning your telephone e Your telephone has a durable plastic casing that should retain its luster for many years Clean it only with a soft cloth slightly dampened with water or mild soap e Do not use excess water or cleaning solvents of any kind Remember that electrical appliances can cause serious injury if used when you are wet or standing in water If the telephone base should fall into water DO NOT RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD AND TELEPHONE LINE CORDS FROM THE WALL Pull the unit out by the unplugged cords 23 Appendix Important safety information that may appear in this user s manual Always follow basic safety This symbol is to alert you to important operating or servicing instructions precautions when using this product to reduce the risk of injury fire or electric shock Safety infor
33. ork must comply with the applicable Part 68 rules and technical requirements adopted by ACTA A compliant telephone cord and modular plug is provided with this product It is designed to be connected to a compatible modular jack that is also compliant An RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for two lines See the installation instructions in the user s manual The Ringer Equivalence Number REN is used to determine how many devices you may connect to your telephone line and still have them ring when you are called The REN for this product is encoded as the 6th and 7th characters following the US in the product identifier e g if is 03 the REN is 0 3 In most but not all areas the sum of all RENs should be five 5 0 or less For more information please contact your telephone service provider This equipment may not be used with Party Lines If you have specially wired alarm dialing equipment connected to your telephone line ensure the connection of this equipment does not disable your alarm equipment If you have questions about what will disable the alarm equipment consult your telephone service provider or a qualified installer If this equipment is malfunctioning it must be unplugged from the modular jack until the problem has been corrected Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents For repair procedures follow the instructions
34. ou might have moved out of range Reset the telephone base Unplug the electrical power Wait for 15 seconds then plug it back in Allow up to one minute for the cordless handset and telephone base to reset Other electronic products such as HAM radios and other DECT phones can cause interference with your cordless phone Try installing your phone as far away as possible from these types of electronic devices The handset registration is unsuccessful Follow the steps to register the handset again 1 Make sure the handset is out of the charger and shows Press HOLD on base for 4 sec then press on handset before you begin Press and hold HOLD on the telephone base for about four seconds until it shows Registering Please wait Then release the button Press pound key on the handset Its screen shows Registering handset and it takes up to 60 seconds to complete the registration The handset shows HANDSET X Registered X represents the handset number assigned and you hear a beep when the registration completes Refer to Add and register a handset on page 11 for details 15 Appendix Troubleshooting Out of range OR no power at base appears on my cordless handset Make sure that the telephone base is powered up Move the cordless handset closer to the telephone base You might have moved out of range Reset the telephone base Unplug the electrical power Wait for 15 seconds then plug it back
35. porelles 28 Appendix For C UL compliance Le sceau de l organisme de recyclage RBRC sur les piles l hydrure m tallique de nickel signifie que le fabricant de cet appareil participe volontairement au programme industriel visant reprendre et recycler ce type de piles lorsqu elles ne servent plus au sein du territoire des tats Unis et du Canada Vous devez apporter ces piles chez un d taillant participant ou le centre de recyclage le plus pr s de chez vous Ou vous pouvez composer le 1 800 8 BATTERY afin de conna tre les endroits qui acceptent les piles l hydrure m tallique de nickel mortes RBRC et 1 800 8 BATTERY sont des marques d pos es de Rechargeable Battery Recycling Corporation Mesures pr ventives pour les utilisateurs de stimulateurs cardiaques implant s dans l organisme Stimulateurs cardiaques ne s applique qu aux t l phones sans fil num riques L organisme Wireless Technology Research LLC WTR une firme de recherche ind pendante a men une valuation pluridisciplinaire des interf rences entre les t l phones sans fil portatifs et les stimulateurs cardiaques implant s dans l organisme Appuy e par l Administration des aliments et drogues FDA des tats unis la firme WTR recommande aux m decins Avis aux d tenteurs de stimulateurs cardiaques e Ils doivent tenir le t l phone sans fil une distance d au moins six pouces du stimulateur cardiaque e Ils ne doive
36. r downwards Lift out the old battery and disconnect it from the handset Follow the instructions on page 6 to install and charge the new battery IMPORTANT INFORMATION 1 Use only the supplied rechargeable battery or replacement battery model BT166342 BT266342 To order visit our website at www telephones att com or cau 1 800 222 3111 In Canada dial 1 866 288 4268 2 If you do not use the handset for a long time disconnect and remove the battery to prevent possible leakage Getting started Battery charging Once you have installed the battery the screen indicates the battery status see the following table If necessary place the handset in the telephone base or charger to charge the battery For best performance keep the handset in the telephone base or charger when not in use The battery is fully charged after 16 hours of continuous charging See the table on page 37 for battery operating times If the screen shows Low battery you need to charge the handset without interruption for at least 25 minutes to give the handset enough charge to use the telephone for a short time The following table summarizes the battery charge indicators and actions to take Battery indicators Battery status Action The screen is blank or The battery has very Charge without interruption shows Place in charger little or no charge The until the screen shows handset cannot be used Low battery or HANDSET X at least five
37. re 27 Appendix For C UL compliance MISES EN GARDE N utilisez seulement l adaptateur inclus avec ce produit Pour obtenir une pi ce de rechange visitez notre site Web au www telephones att com ou composez le 1 800 222 3111 Au Canada composez le 1 866 288 4268 N utilisez que la pile de rechargeable incluse ou une pile de rechange mod le BT166342 BT266342 Pour commander visitez notre site Web www telephones att com ou composez le 1 800 222 3111 Au Canada composez le 1 866 288 4268 Afin de pr venir les risques d incendie ou d explosion de la pile replacez la pile avec une pile du m me type Jetez les piles puis es en respectant les instructions Sp cifiquement en rapport avec les t l phones sans fil Confidentialit Les m mes caract ristiques qui rendent les t l phones sans fil si pratiques cr ent galement des restrictions Les appels t l phoniques sont transmis entre le socle du t l phone et le combin par le biais d ondes radio et il se peut que vos conversations t l phoniques soient intercept es par d autres quipements de r ception d ondes radio au sein de la port e du t l phone sans fil Pour cette raison vous ne devez pas consid rer les conversations sur un t l phone sans fil comme tant aussi confidentielles que celles d un t l phone cordon Alimentation lectrique La base de ce t l phone sans fil doit tre branch e une prise de courant lectrique fonction
38. rsation SAVE THESE INSTRUCTIONS 26 Appendix For C UL compliance In compliance with the bilingual requirements for safety caution and warning markings of Canadian Federal and Provincial Territorial statutes and regulations the French version of Important safety information is included Mesures de s curit importantes d entretien pouvant appara tre dans ce guide d utilisation Respectez Ce symbole vous alertera d informations importantes ou d instructions toujours les mesures de s curit et de s curit de base lorsque vous utilisez ce produit afin de r duire les risques de blessures d incendie ou d lectrocution Information relative la s curit Veuillez lire et comprendre toutes les instructions de ce guide d utilisation Relectez toutes les inscriptions apparaissant sur le produit vitez d utiliser le t l phone pendant un orage Il pourrait y avoir un faible risque d lectrocution N utilisez pas un t l phone proximit d une fuite de gaz Si vous soup onnez la pr sence d une fuite de gaz rapportez la imm diatement mais utilisez un t l phone situ dans un autre endroit que celui de la fuite de gaz Si ce produit est un mod le sans fil assurez vous que le socle du t l phone se trouve galement l ext rieur de cet endroit N utilisez pas ce produit pr s de l eau ou lorsque vous tes mouill s Par exemple ne l utilisez pas dans des sous sols humides ou sous la douche ou
39. t is in use e You cannot register more than 12 handsets to the telephone base Registration slots are full shows on the base screen while you are in step 2 11 Adding handset to your telephone base Replace a handset If you want to replace a handset or reassign the designated handset number of a registered handset you must deregister all the handsets and then individually register each handset To make deregistration easier read all of the instructions on this page before you begin To deregister all handsets 1 Press and hold FLASH on the telephone base for about 4 seconds until it shows Deregister all handsets Then release the button 2 Press the YES softkey to continue You hear a confirmation tone from the telephone base 3 The telephone base displays PLEASE WAIT All system handsets show Out of range OR no power at base for a few seconds and then you hear a confirmation tone from the handset 4 All the handsets show Press HOLD on base for 4 sec then press on handset when the deregistration completes The deregistration process takes about 10 seconds to complete If deregistration fails you may need to reset the telephone and try again To reset e Unplug the power from the telephone base then plug it back in After deregistering register each handset individually See Add and register a handset on page 11 Owores e You cannot deregister the handset s if any other system handset is in use
40. t is off Make sure the power and line cords are plugged in correctly and securely Unplug the electrical power Wait for 15 seconds then plug it back in Allow up to one minute for the cordless handset and telephone base to reset Clean the cordless handset and charger charging contacts each month using a pencil eraser or cloth My caller ID isn t working Caller ID is a subscription service You must subscribe to this service from your telephone service provider for this feature to work on your phone The caller must be calling from an area that supports caller ID Both your and your caller s telephone service providers must use caller ID compatible equipment If you subscribe to high speed Internet service DSL digital subscriber line through your telephone lines you must install a DSL filter between each telephone line cord and telephone wall jack The filter prevents noise and caller ID problems caused by DSL interference Please contact your DSL service provider for more information about DSL filters My telephone does not receive caller ID when on a call Make sure you subscribe to caller ID with call waiting features provided by your telephone service provider Caller ID features work only if both you and the caller are in areas offering caller ID service and if both telephone companies use compatible equipment 21 Appendix Troubleshooting subscribe to a nontraditional telephone service that uses my co
41. tal apparatus complies with Canadian requirement CAN ICES 3 B NMB 3 B For body worn operation this handset has been tested and meets FCC RF exposure guidelines when used with an accessory that contains no metal and that positions the handset a minimum of Omm from the body Use of other accessories may not ensure compliance with FCC RF exposure guidelines 32 Appendix California Energy Commission battery charging testing instructions This telephone is set up to comply with the energy conserving standards right out of the box These instructions are intended for California Energy Commission CEC compliance testing only When the CEC battery charging testing mode is activated all telephone functions on the cordless handsets except battery charging will be disabled When first purchased and properly installed for charging see Battery installation and charging on pages 6 7 put the handset in the handset charger to charge The CEC battery charging testing mode is activated while charging If you have registered the handset to the TL86109 base below are the testing instructions To activate the CEC battery charging testing mode 1 When the phone is not in use press and hold FLASH on the telephone base for about 4 seconds until it shows Deregister all handsets Then release the button 2 Press the YES softkey to continue You hear a confirmation tone from the telephone base 3 The telephone base displays PLEASE WAIT
42. to the left Getting started Quick reference quide While reviewing a caller ID history entry press repeatedly to add or remove 1 in front of the telephone number before dialing or saving it in the directory TONE X Press to switch to tone dialing temporarily during a call if you have pulse service 4 SPEAKER xI Press to turn on the w8 handset speakerphone Press again to resume normal handset use w0 HOLD Bluetooth HOLD Press to put a call on hold 1 LINE FLASH 2 LINE FLASH Press 1 LINE FLASH to make or answer a call on line 1 During a call press to answer an incoming call on line 1 when you receive a call waiting alert Press 2 LINE FLASH to make or answer a call on line 2 During a call press to answer an incoming call on line 2 when you receive a call waiting alert pound key Press repeatedly to display other dialing options when reviewing a caller ID history entry REDIAL PAUSE Press to view the redial list While entering numbers press and hold to insert a dialing pause Getting started Quick reference quide ea El During an outside call intercom call message or announcement playback press to change the quality of the audio to best suit your hearing Press the MENU softkey to enter the main menu which includes the following PLAY MESSAGES ANSWERING SYS DIRECTORY CALL LOG INTERCOM RINGER SETTINGS WEBSITE Getting started
43. your new telephone base as far as possible from any other existing cordless telephone system that may already be installed Other electronic products such as HAM radios and other DECT phones can cause interference with your cordless phone Try installing your phone as far away as possible from these types of electronic devices Do not install this phone near a microwave oven or on the same electrical outlet You may experience decreased performance while the microwave oven is operating If your phone is plugged in with a modem or a surge protector plug the phone or modem surge protector into a different location If this doesn t solve the problem relocate your phone or modem farther apart from one another or use a different surge protector Relocate your phone to a higher location The phone may have better reception when installed in a high area If other phones in your home are having the same problem the problem is in your wiring or local service Contact your telephone service provider charges may apply 17 Appendix Troubleshooting experience poor sound quality when using the speakerphone For increased sound quality while using the handset speakerphone place the handset on a flat surface with the dial pad facing up When using a speakerphone controlling background noise in your environment is essential While you are listening to your party press the MUTE softkey to temporarily turn your microphone off When
Download Pdf Manuals
Related Search