Caddx 9000e Manual
Contents
1. Beeps 1 second at the end of the exit delay AUDIBLE ALARM SOUNDS FIRE Steady Siren Beeping Keypad INTRUSION amp PANIC Yelp siren RESETTING YOUR SECURITY CONTROL CENTER In the event of a system malfunction in the Security Control Center press the reset key on the keypad control This should reset the code sequence and restore normal operation If the problem persists call the service number located on page 1 of this booklet for service ALARM MEMORY To obtain the last alarm information press D 0 and wait 5 seconds All zones violated during last alarm will flash All zones bypassed during last alarm will be a steady light _ QUICK ARM FEATURE If checked your security system has a QUICK ARM code programmed This feature will allow you to arm the security system by pressing one pre designated key on the keypad control This QUICK ARM code is for ARMING ONLY and will not disarm the security system This makes it ideal for a maid code babysitter code etc This code can only be programmed and or changed by your installing company AUTOMATIC BYPASS OPTION If checked your installing company has selected the AUTOMATIC BYPASS option With this feature enabled all interior zones will automatically bypass if you ARM your security system and do not leave through a designated entry exit door The AUTOMATIC BYPASS will occur at the end of the exit delay time At this time all bypassed ZONE lights wi2. UNDERSTAND ANY PORTION OF THIS MANUAL OR IF YOU HAVE ANY QUESTIONS ABOUT YOUR SYSTEM CONTACT THE INSTALLING COMPANY LISTED ON PAGE 1 OF THIS BOOKLET HOW TO ARM YOUR SECURITY SYSTEM To turn the security system on close all of the protected doors and windows The green READY light on the keypad control will illuminate when all of the protected areas and sensors are secure If any of the zones are bypassed a sensor in that zone can be violated without affecting the READY light The security system will not arm if the READY light is not illuminated With the READY light on you may arm the security system with your master code or one of the auxiliary codes Each time a key is pressed on the keypad control a short tone beep will sound If the keypad beeps three times after the code entry or if it does not arm it is an indication that the code has not been accepted Press the key to reset and re enter a valid code If the keypad control beeps continuously after code entry it is an indication that the POWER light is off the FIRE and or TROUBLE light is on or a phone line fault problem has been detected The keypad sounder can be silenced by re entering your four digit code If the POWER light is off you should restore power to the system if possible If the FIRE and or TROUBLE light is on you should press the key reset and wait 10 seconds If you are unable to correct the above conditions you should contact the
3. the Smoke or Heat detectors should be tested at least monthly If your Security System is monitored by a Central Monitoring Station always call beforehand to let them know that you are about to conduct a test of the fire detection system Always call after the test to ask for results and to put your fire detection system back into service If the Siren Bell test option has been selected by your installing company you may activate the siren bell by pressing the one 1 and 7 keys at the same time for one second To silence the siren bell enter your 4 digit master or auxiliary code IF ANY OF THE ABOVE TESTS ARE NOT SUCCESSFUL OR THE RESULTS UNCLEAR CONTACT YOUR SERVICE COMPANY AT THE PHONE NUMBER LISTED ON PAGE 1 OF THIS BOOKLET THIS SYSTEM HAS BEEN LISTED BY UNDERWRITERS LABORATORIES FOR GRADE A LOCAL GRADE B 8 C CENTRAL STATION POLICE CONNECT WITH BASIC LINE SECURITY GRADE A HOUSEHOLD BURGLARY AND HOUSEHOLD FIRE EMERGENCY EVACUATION PLANS An emergency evacuation plan should be established for an actual fire alarm condition For example the following steps are recommended by the National Fire Protection Association and can be used as a guide in establishing an evacuation plan for your building Draw up a floor plan of your home Show windows doors stairs and rooftops that can be used for escape Indicate each occupant s escape routes Always keep these routes free from obstruction Determine two means of escape from each ro
4. BEDROOM FIRST FLOOR vv SECOND FLOOR 9000E USER S MANUAL 9000EUD98 REVD 02 10 98 Caddx Controls Inc
5. SECURITY SYSTEM NOTES Installing Service Company For Service Call SPECIAL CODES Master Code Duress Code Quick Arm Digit Chime Digit Entry Guard Digit AUXILIARY ARM DISARM CODES 02 12 22 03 13 23 04 14 24 05 15 25 06 16 26 07 17 27 08 18 28 09 19 29 10 20 30 11 21 ENTRY EXIT DELAY TIMES Exit Delay Time Secondary Exit Delay Time Entry Delay Time Secondary Entry Delay Time ZONE DESCRIPTIONS 01 12 23 02 13 24 03 14 25 04 15 26 05 16 27 06 17 28 07 18 29 08 19 30 09 20 31 10 21 32 11 22 THIS MANUAL IS FURNISHED TO HELP YOU UNDERSTAND YOUR SECURITY SYSTEM AND BECOME PROFICIENT IN ITS OPERATION ALL USERS OF YOUR SECURITY SYSTEM SHOULD READ AND FOLLOW THE INSTRUCTIONS AND PRECAUTIONS IN THIS BOOKLET FAILURE TO DO SO COULD RESULT IN THE SECURITY SYSTEM NOT WORKING PROPERLY THIS BOOKLET SHOULD BE KEPT IN AN ACCESSIBLE LOCATION FOR THE LIFE OF THE SECURITY SYSTEM IF YOU DO NOT UNDERSTAND ANY PART OF THIS MANUAL YOU SHOULD NOTIFY YOUR INSTALLING COMPANY AND ASK FOR THAT SECTION OF THE MANUAL TO BE EXPLAINED FULLY The SECURITY CONTROL CENTER is turned on ARMED and off DISARMED by entering a 4 digit code into the Keypad Control which is similar to a telephone keypad The Keypad Control includes 22 lights and a built in electronic sounder These provide specific information r
6. cur in conjunction with the AUTOMATIC BYPASS feature In this case the INSTANT light and the bypassed ZONE lights will become illuminated at the end of the exit delay If this occurs you still have the ability to turn the INSTANT feature off and or on by pressing the gt key ENTRY GUARD OPTION If checked your installing company has selected the ENTRY GUARD option If you wish to arm your system in a low security mode you may do so by pressing the preset ENTRY GUARD digit see page 1 for the selected digit Five seconds later the security control will bypass all non ENTRY GUARD zones and arm the system with all Entry Guard zones delayed This mode of operation will allow you time to DISARM turn off the security system in the event a zone is accidently opened E KEYPAD ACTIVATED PANIC HOLD UP ALARM If checked your installing company has selected this feature If so when the star 2 and pound keys are pressed at the same time for one second a local audible alarm will sound If your system is connected to a monitoring center an emergency report could be transmitted to that center These keys should only be pressed in an emergency situation requiring immediate response by law enforcement personnel PLEASE NOTE Some Panic Hold up alarms are programmed to be silent at the protected site while reporting an alarm to the monitoring center Check with your installing company to determine how your security syst
7. e MULTI AREA option for your security system If so it may be possible to ARM different areas of your building independently from each other The system may have up to 4 independent areas To view another area from a keypad a special Change Area Code will be required To change the current area being viewed on the keypad control press C 9 9 this tells the control you want to access another area Then enter the change area code for example 4 3 2 1 followed by the key 1 to 4 representing the area to be viewed For instance to change the area to area 3 the sequence would be as follows C 9 9 4 3 2 1 3 PROGRAMMING ARM DISARM CODES The security system can be armed and disarmed by the Master code User Code 1 and up to 29 auxiliary codes All codes must have 4 digits These Auxiliary codes are individually numbered from 2 to 30 NOTE If your system is programmed for a DURESS code above user code 15 will not be available If Auxiliary codes are desired they must be programmed individually Only persons knowing the master code can assign or change auxiliary codes See Programming Auxiliary Codes on page 6 CHANGING THE MASTER CODE The master code is user code 1 and must be programmed by referring to its code For example if the Master code is 1 2 3 4 and you want to change it to 5 3 4 2 the sequence would be as follows Press C 0 1 this enters program
8. elating to the status of the security system which is described in this booklet Understanding what the lights and sounds mean will help you easily operate your system SO REMEMBER READ THE ENTIRE MANUAL AND IF POSSIBLE PRACTICE ON THE KEYPAD CONTROL WHILE YOUR PROFESSIONAL INSTALLER IS AT YOUR BUILDING IF YOU HAVE ANY QUESTIONS ASK YOUR INSTALLING COMPANY PLEASE KEEP IN MIND THAT THE LEVEL OF SECURITY YOU WILL OBTAIN WITH THIS SYSTEM RELATES SPECIFICALLY WITH TWO MAJOR FACTORS 1 The quantity quality and placement of security devices attached to this system 2 The knowledge you have of the security system and how that knowledge is utilized in a weekly test of the complete system YOU SHOULD BE AWARE OF THE FOLLOWING FACTS WHEN PREPARING A SAFETY SECURITY PLAN FOR YOUR HOME BUSINESS 1 Your security system is an electronic device and is subject to failure or malfunction Do not rely on it as your single source of security 2 Your system should be tested weekly 3 Your system will not work without power 4 Warning devices will need to be loud enough wired correctly and properly placed to provide notification of an alarm event 5 Smoke and heat detectors may not detect heat and smoke in all situations 6 Use qualified security professionals to select install and maintain your security system PLEASE READ THE FOLLOWING INFORMATION AND INSTRUCTIONS CAREFULLY BEFORE OPERATING YOUR SECURITY CONTROL SYSTEM IF YOU DO NOT
9. em will respond to the Panic Hold up activation KEYPAD ACTIVATED FIRE ALARM If checked this feature has been selected by your installing company If so you can activate the steady siren by pressing the one 1 and three 3 keys at the same time for one second If your system is connected to a monitoring center an emergency report could be sent to that center These keys should only be pressed in an emergency situation requiring response by fire department personnel KEYPAD ACTIVATED AUXILIARY ALARM If checked this feature has been selected by your installing company If so you can activate the auxiliary alarm by pressing the four 4 and six 6 keys at the same time for one second If your system is connected to a monitoring center an emergency report could be sent to that center These keys should only be pressed in an emergency situation requiring response by emergency personnel When the 4 and 6 are pressed together the keypad will start to beep until a code is entered E FIRE ZONE If checked your system has designated FIRE zones When this option is selected and approved heat or smoke detectors are attached to the selected zones a steady audible siren can be initiated from the security system You should familiarize yourself and your family or staff with this sound and follow an evacuation plan ifthis FIRE warning sound is heard See page 8 for assistance in formulating an evacuation plan To silence the aud
10. ible FIRE alarm enter a valid code To reset the FIRE light and or smoke detectors press the Reset button on the keypad After 10 seconds the FIRE light should extinguish and the light on the affected smoke detector should go out If you are unable to reset the FIRE light or smoke detector after all smoke has cleared you should immediately call the service phone number listed on page 1 of this booklet Duress CODE If checked your security system has a DURESS CODE option If so this code may be programmed to send a special message to the central monitoring station if you are forced to arm or disarm your security system against your will Check with your Installing Servicing company to see if this option has been enabled for your system TURNING ON THE CHIME FEATURE If checked your security system will operate in the CHIME mode allowing the monitoring of pre designated zones while the security system is not armed While in the CHIME mode the opening of any of these zones will produce a 1 second beep from the keypad control To use this feature press the CHIME digit this digit has been selected by your installing company and is noted on page 1 Five seconds after pressing the CHIME digit a beep will occur indicating that this feature has been activated Repeat this procedure to turn the CHIME feature off E SPECIAL INSTRUCTIONS FOR MULTI AREA SYSTEMS If checked your installing company has selected th
11. installing company listed on page 1 of this booklet for service When the security system has accepted a valid code the red ARMED light will illuminate indicating that the system has been turned on If you choose to leave the protected area you must exit through a designated exit door within the exit delay time noted on page 1 If you choose to stay within the protected area insure that all interior zones that may be tripped by your movement are bypassed HOW TO DISARM YOUR SECURITY SYSTEM When you enter the protected area through one of the designated entry exit doors the keypad control will sound a continuous tone beep for the duration of the entry delay time or until you enter a valid code After a valid code has been entered the red ARMED light will turn off and the tone will stop The security system is now DISARMED If a valid code is not entered before the end of the entry delay time an alarm will occur NOTE IF THE RED ARMED LIGHT IS FLASHING DURING THE ENTRY DELAY THE ALARM SYSTEM HAS BEEN ACTIVATED IN YOUR ABSENCE LEAVE THE BUILDING IMMEDIATELY AND CALL YOUR ALARM COMPANY AND OR THE POLICE FROM A SAFE LOCATION HOW TO BYPASS ZONES To bypass any of the zones disarm the control and press zone number s to be bypassed and Zone numbers less than 10 must be proceeded by a zero for example 01 02 03 Zones cannot be bypassed or unbypassed while the control is in the armed state Upon disarming all bypassed z
12. ll become illuminated With the interior zones bypassed occupants are allowed the freedom of movement inside of the Home Business while the security system is ARMED GROUP BYPASS OPTION If checked your installing company has selected the GROUP BYPASS option If you wish to bypass all zones designated as GROUP BYPASS zones you may do so by pressing the key during the exit delay Once these zones have been bypassed they will remain bypassed until the system is disarmed Once GROUP BYPASS zones have been bypassed the AUTOMATIC BYPASS option will not take effect for this arming time INSTANT DELAY OPTION If checked your installing company has selected the INSTANT option With this feature enabled if you do not wish to have a delay on your entry exit doors this can be accomplished by pressing the x key on your keypad while the system is ARMED At this time the INSTANT light will illuminate and there will be no entry delay when the entry exit doors are opened Any time the INSTANT light is on and the exit delay has expired the opening of an entry exit door will produce an immediate alarm making this feature ideal when a high level of security is desired and no authorized entries are anticipated By pressing the k key again the INSTANT light will turn off and an entry delay will be present on designated entry exit doors NOTE Your installing company may have programmed the INSTANT option to oc
13. ming for user 1 Then press 1 2 3 4 old Master code followed by the new master code 5 3 4 2 The entire sequence would consist of pressing 11 keys as follows C 0 1 1 2 8 4 5 3 4 2 PROGRAMMING AUXILIARY CODES In order to program Auxiliary Codes you mustknow the Master code As stated earlier each auxiliary code has its own unique number from 2 to 30 and must be referred to by its number It is programmed much like the Master Code For example to program Auxiliary user code 2 the sequence would be as follows C 0 2 5 8 4 2 1 11 11 17 New Code REMOVING AUXILIARY CODES To remove an Auxiliary user code simply program that code as k k k For example to remove user code 24 the sequence would be as follows C 2 4 5 8 4 2 TESTING YOUR SECURITY SYSTEM There are several tests you should perform on a periodic basis at least once a week to insure that your Security System is functioning properly Enable THE CHIME feature and open all protected windows and doors The Keypad Control should sound beep for each device and the appropriate yellow zone light should blink Walk into all areas protected by motion detection devices while someone observes the Keypad Control The appropriate yellow zone light should blink for each sensor tested If your system has a FIRE zone
14. om One will be the normal exit from the building The other may be a window that opens easily An escape ladder may have to be located near the window if there is a long drop to the ground below Set a meeting place outdoors for a headcount of the building occupants Practice escape procedures In a home sleep with bedroom door closed this will increase your escape time If you suspect fire test the door for heat If you think it is safe brace your shoulder against the door and open it cautiously Be ready to slam the door if smoke or heat rush in Practice escaping to the outdoors and meeting in an assigned spot Call the Fire Department from a neighbor s phone NOTE After the installation of your Security System has been completed notify your local Fire and Police Departments to give them your name and address for their records Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms This equipment should be installed in accordance with the National Fire Protection Association s Standard 72 Chapter 2 For additional information write the National Fire Protection Association Batterymarch Park Quincy MA 02269 The following are examples of evacuation plans A plan unique to your home or business should be drawn and memorized by each occupant 4 PA KITCHEN SEES i BEDROOM A 7 Ps E os ay DINING a ROOM O ESON BEDROOM
15. ones will be unbypassed As bypassed zones are not protected the bypass procedure should only be given to authorized persons KEYPAD CONTROL LIGHT INDICATORS ARMED RED LED is on while system is armed off otherwise Blinks as alarm memory if alarm was activated during arming cycle READY GREEN LED is on when all zones are secure and or Bypassed and the system is ready to arm off otherwise INSTANT RED LED is on while the entry exit zones are instant or the Entry Guard is on off otherwise POWER RED LED is on while AC power is on off otherwise Blinks when the system standby battery is low FIRE RED LED is on when a fire zone has been activated off otherwise TROUBLE RED LED is on when a fire zone has been in trouble off otherwise KEYPAD CONTROL TONES BEEPS A sounder is built into the keypad control and may sound for one of the following reasons Beeps for all keypresses Beeps continuously during the Entry delay time Pulses when a day zone is violated and the system is disarmed a FIRE zone has a trouble condition or when the armed status changes and the AC power is off or a FIRE TROUBLE condition exists When pulsing it may be silenced by entering a valid code The Armed state of your security system will not change when you enter a code to silence a pulsing sounder Pulses when a phone line fault is detected 3 beeps for trying to arm with the READY light off Beeps 1 second for the CHIME feature
Download Pdf Manuals
Related Search