Home

Industrial Management Ethernet Switch

Contents

1. IGS 3044GC GP Industrial Managed Ethernet Switch User s Manual Version 3 0 Feb 2013 www oring networking com ORing Industrial Networking Corp ORing Industrial Networking Corp yA IGS 3044GC User s Manual COPYRIGHT NOTICE Copyright 2010 ORing Industrial Networking Corp All rights reserved No part of this publication may be reproduced in any form without the prior written consent of ORing Industrial Networking Corp TRADEMARKS ons All other trademarks belong to their respective owners is a registered trademark of ORing Industrial Networking Corp REGULATORY COMPLIANCE STATEMENT Product s associated with this publication complies comply with all applicable regulations Please refer to the Technical Specifications section for more details WARRANTY ORing warrants that all ORing products are free from defects in material and workmanship for a specified warranty period from the invoice date 5 years for most products ORing will repair or replace products found by ORing to be defective within this warranty period with shipment expenses apportioned by ORing and the distributor This warranty does not cover product modifications or repairs done by persons other than ORing approved personnel and this warranty does not apply to ORing products that are misused abused improperly installed or damaged by accidents Please refer to the Technical Specifications section for the actual warranty period
2. client ORing Industrial Networking Corp 57 IGS 3044GC User s Manual DHCP Relay Agent Mode DHCP Server IP Address Let Server IP SI 2nd Server IP 0 0 0 0 3rd Server IP OCL Ath Server IP OAN DHCP Option 82 Remote ID Type Value 192 168 10 Display DHCP Option 82 Circuit ID Table Port No Circuit ID Option 82 Port 01 ooo4oo010001 2 Port 02 ooo4ooo10002 Port 03 ooo400010003 OO Port 04 oooao0010004 Port 05 ooo400010005 O Port 06 000400010006 The following table describes the labels in this screen Label Description DHCP Relay Enable Disable DHCP Relay Agent DHCP Server IP Specify the IP address and VID of DHCP server Keep 0 0 0 0 means Address and VID Sever is inactive DHCP Option 82 Option 82 Remote ID provides a identifier for the remote server Remote ID There are 4 types supported IP MAC Client ID and Other DHCP Option 82 Option 82 Circuit ID encodes an agent local identifier of the circuit Circuit ID Table from which a DHCP client to server packet was received It is intended for use by agents in relaying DHCP responses back to the proper circuit Apply Click Apply to set the configurations ORing Industrial Networking Corp 58 5 1 7 SNMP IGS 3044GC User s Manual Simple Network Management Protocol SNMP is the protocol developed to manage nodes servers workstations routers switches and hubs etc on an IP network SNMP enables
3. ORing Industrial Networking Corp 61 IGS 3044GC User s Manual The following table describes the labels in this screen Label Context Table User Table Group Table Access Table MiBview Table ORing Industrial Networking Configure SNMP v3 context table Assign the context name of context table Click Apply to change context name Configure SNMP v3 user table User ID set up the user name Authentication Password set up the authentication password Privacy Password set up the private password Click Add to add context name Click Remove to remove unwanted context name Configure SNMP v3 group table Security Name User ID assign the user name that you have set up in user table Group Name set up the group name Click Add to add context name Click Remove to remove unwanted context name Configure SNMP v3 access table Context Prefix set up the context name Group Name set up the group Security Level select the access level Context Match Rule select the context match rule Read View Name set up the read view Write View Name set up the write view Notify View Name set up the notify view L E 3 4 5 6 7 8 d Click Add to add context name kel Click Remove to remove unwanted context name Configure MIB view table ViewName set up the name Sub Oid Tree fill the Sub OID Type select the type exclude or included Click Add to add context
4. a frame is modified during transmission e g to add or remove a OutFCSErr tag the frames s original FCS is inspected before a new FCS is added to a modified frame If the original FCS is invalid the new FCS is made invalid too and this counter is incremented The number of good frames received that have a Unicast wn destination MAC address The total number of successfully transmitted frames that Deferred experienced no collisions bu are delayed because the medium was busy during the first attempt This counter is applicable in ORing Industrial Networking Corp SH InBroadcasts Octets64 Octets127 OutOctetsLo Excessive OutBroadcasts OutPause O J gt 3 si c D rF D Z D asa O x IGS 3044GC User s Manual half duplex only The number of good frames received that have a Broadcast destination MAC address The number of good frames received that have a Multicast destnation MAC address Total frames received and or transmitted with a length of exactly 64 octes include those with errors Total frames received and or transmitted with a length of between 65 and 127 octes in clusive including those with error Total frames received and or transmitted with a length of between 128 and 255 octes in clusive including those with error Total frames received and or transmitted with a length of between 256 and 511 octes in clusive including those with error Total frames received and or
5. s a lt Port 07 ERs Port 08 Port based Priority interface The following table describes the labels in this screen Port base Priority Assign Port with a priority queue 4 priority queues can be assigned High Middle Low and Lowest Apply Click Apply to set the configurations 5 1 5 3 COS 802 1p COS 802 1p COS Port Default Port No COS Port 01 Port 02 Port 03 COS Priority EE ES fz COS 802 1p interface ORing Industrial Networking Corp 54 IGS 3044GC User s Manual The following table describes the labels in this screen COS 802 1p COS Class Of Service is well known as 802 1p It describes that the output priority of a packet is determined by user priority field in 802 1Q VLAN tag The priority value is supported Oto7 COS value map to 4 priority queues High Middle Low and Lowest COS Port Default When an ingress packet has not VLAN tag a default priority value is considered and determined by ingress port Click Apply to set the configurations Hep Shown ep 5 1 5 4 TOS DSCP TOS DSCP DSCP un ESP DSCP priority SR DSCP erty DEI DSCP erty EIS DSCP aces Priority DSCP Priority SE a DSCP priority EM DSCP St TOS DSCP interface The following table describes the labels in this screen TOS DSCP TOS Type of Service is a field in IP header of a packet This TOS field is also used by Differentiated Services and is ca
6. Click Apply to activate the configurations MSTP Bridge Port Path Cost 1 200000000 0 Auto Admin Admin Admin P2P Edge Non Stp Priority 0 240 priority must be a multiple of 16 Apply MSTP Port interface Description Selecting the port that you want to configure Priority 0 240 Decide which port should be blocked by priority in LAN Enter a number 0 through 240 The value of priority must be the multiple of 16 Path Cost The cost of the path to the other bridge from this transmitting 1 200000000 bridge at the specified port Enter a number 1 through 200000000 Admin P2P some of the rapid state transactions that are possible within RSTP are dependent upon whether the port concerned can only ORing Industrial Networking Corp 39 IGS 3044GC User s Manual be connected to exactly one other bridge i e It is served by a point to point LAN segment or it can be connected to two or more bridges i e It is served by a shared medium LAN segment This function allows the P2P status of the link to be manipulated administratively True means P2P enabling False means P2P disabling Apply Click Apply to activate the configurations MSTP Instance Setting 2 Priority Instance State VLANS 0 61440 Priority must be a multiple of 4096 Ehe Ai MSTP Instance interface instance Sethwinsancetom 1015 site Enae or asane meins Proprietary 0 61440 A value use
7. Networking Corp 27 IGS 3044GC User s Manual 5 1 4 9 Upgrade Firmware Upgrade Firmware allows you to update the switch firmware Before updating make sure you have your TFTP server ready and the firmware image is on the TF TP server Upgrade Firmware From TFTP Server TFTP Server IP 192 168 10 2 Firmware File Name From Local PG Upgrade Update Firmware interface 5 1 1 Redundancy 5 1 1 1 MRP MRP Media Redundancy Protocol Ring IEC 62439 of up to 50 devices typically transforms back to a line structure within 80 ms adjustable to max 200 ms 500 ms MRP Enable E E Manager W React on Link Change E ist Ring Port Linkdown 2nd Ring Port Forwarding p E Force Speed Duplex for 100BASE TX Apply ORing Industrial Networking Corp 28 IGS 3044GC User s Manual Enable Enabling the MRP function Manager MRP Master every one MRP topology need setting one device to Manager one MRP topology only can setting one device to Manager if user setting two or more switch to Manager this MRP topology will fail React on Link Change Faster mode if user enable this function MRP Topology will Advanced mode more faster convergence this function only can setting in MRP Manager Switch 17 Ring Port Choosing the port which connect to the MRP ring 2 Ring Port Choosing the port which connect to the MRP ring Force Speed Duplex Port Speed Duplex default is autonegotiation mode Enable for
8. eee ee ee ae ee eee ee ene 55 Se WOT EE 56 5 1 6 1 DHCP Server Setting naasi naina ah h as ah raaa aaa A ES 56 5162 DHOP Sener Cliont LiSteiccct ce ceencecs Mee 57 5 1 6 3 DHCP Server Port and IP bindings ccccceeccceeeeeeeeeeeeeeseeeeseeeeaaees 57 5 1 6 4 DHCP Server DHCP Relay Agent 57 en KT ade aes tcat EA ace craters neierceh o sereecaturteatatatunenatansantananenananetane 59 51 71 SNMP Agent e Le EE 59 Silehee SNMP Tran Seung DEE 60 eg e STE 2 enee EAA 61 ORing Industrial Networking Corp 3 IGS 3044GC User s Manual See eo MNES lt 10114 ae eRe Rees eee EE 63 5 1 8 1 Management Security cccccecccceeeeceeeeceeeeceeeeseeeseeeessueeseeeesseeesaeeessaees 63 Dilgore Statie MAG Forwarding DE 63 SROS DAC BECKI e 64 SPE s E SE KE 65 e sic Er EE 68 SS VV AN UMN Gl EE 71 5 1 10 Monitor ANG DIAG EE 74 i Hee SVEEN EEO EE 74 5 1 10 2 MAG Address Table vcciciccaicactccntccatcentesateausecemdadindisetectaantadinetsaeheoontinn 75 D103 ing EEN 76 ule tO PON ere TE 77 ee le E gei GC de te lee BEE 79 SCHER Tratt EE stet eseeeseue geegent 80 Osa i Late DEE 81 5 1 11 Save COMMOUIAUON sis niet tie oie es ae ee eG 81 5 1 12 AGONY ET t sates aceantaenenctennssenan nanny anonndtenadiascasnaasaaaarasaaaniaeaaacnaaaaiacaexe ss 82 5 1 13 SV SION EENEG 82 Command Line Interface Management ccccceeseesseseeeeeneeeeneeeeeneeeennens 83 6 1 ADOUT CLI MANAGEMEN EE 83 6 2 Commands Set
9. of those available at the ORing Industrial Networking Corp 86 Privileged EXEC Global configuration VLAN database Interface configuration Enter the enable command while in user EXEC mode Enter the configure command while in privileged EXEC mode Enter the vlan database command while in privileged EXEC mode Enter the interface command with a specific interface while in global configuration mode Symbol of Command Level Symbol of Command Level User EXEC Privileged EXEC Global configuration VLAN database ORing Industrial Networking Corp switch switch co nfig switch vla n switch co nfig if IGS 3044GC User s Manual disable to exit To exit to privileged EXEC mode enter exit or end To exit to user EXEC mode enter exit To exit to global configuration mode enter exit To exist privileged EXEC mode or end privileged level Use this mode to e Enter menu mode e Display system information The privileged command is advance mode Privileged this mode to e Display advance function status e save configures Use this mode to configure parameters that apply to your Switch as a whole Use this mode to configure VLAN specific parameters Use this mode to configure parameters for the switch and Ethernet ports 87 IGS 3044GC User s Manual Interface configuration 6 2 Comman
10. of SNTP and system clock System Clock Time Setting system Clock System Clock Thu Jan 01 1970 00 39 12 GMT 0800 elek System Date eegen ep YYYY MM DD 2012 System Time hh mm ss Apply Set Clock From PC Help The following table describes the labels in this screen System clock This field shows the current system timer The time stamp could be assigned by manual configuration or by SNTP server System Date Specify the year month and day of system clock YYYY MM DD mm Year 2006 2015 Month Jan Dec Day 1 31 28 System Time Specify the hour minute and second of system clock hh mm ss _ Hour 0 24 Minute 0 59 Second 0 59 ORing Industrial Networking Corp 21 IGS 3044GC User s Manual SNTP The SNTP Simple Network Time Protocol settings allow you to synchronize switch clocks in the Internet SNTP Client UTC Timezone SMT Greenwich W me Dublin Edinburgh Lisbon London SNTP Server Address Daylight Saving Period Daylight Saving Offset Apply SNTP Configuration interface The following table describes the labels in this screen Label Description SNTP Client Enable or disable SNTP function to get the time from the SNTP server Daylight Saving Time Enable or disable daylight saving time function When daylight saving time is enabling you need to configure the daylight saving time period UTC Time zone Set the switch location time zone The following table l
11. range subnet mask The gateway in your network me Domain Name Server IP Address in your network Lease Time It is the period that system will reset the assigned dynamic IP to ensure Hour the IP address is in used Apply Click Apply to set the configurations ORing Industrial Networking Corp 56 IGS 3044GC User s Manual 5 1 6 2 DHCP Server Client List When the DHCP server function is activated the system will collect the DHCP client information and display in here DHCP Server Client List Type Status Lease DHCP Server Client Entries interface 5 1 6 3 DHCP Server Port and IP bindings You can assign the specific IP address which is in the assigned dynamic IP range to the specific port When the device is connecting to the port and asks for dynamic IP assigning the system will assign the IP address that has been assigned before in the connected device DHCP Server Port and IP Binding Port Dort ieee 192 1668 10 125 Port 02 U DUU Port 03 UU UU 0 Port 05 0 000 DHCP Server Port and IP Binding interface 5 1 6 4 DHCP Server DHCP Relay Agent The DHCP relay agent relays DHCP messages between clients and servers for DHCP on different subnet domain DHCP relay agent use Option 82 to insert specific information into a request that is being forwarded to a DHCP server and according to Option 82 to remove the specific information from a reply packets when forwarding server DHCP packets to a DHCP
12. separate by a comma ex 2 3 6 Workport The amount of work ports this value could not be less than zero or be large than the amount of member ports aggregator group Assign a static trunk switch contig aggregator group 1 GroupID Port list nolacp group 2 4 nolacp GroupID 1to3 or Port list Member port switch config aggreator group 1 list This parameter 3 1 2 nolacp could be a port range ex 1 4 or a port list separate by a comma ex 2 3 6 show aggregator Show the information switch show aggregator s e no aggregator lacp function of trunk group no aggregator group emove a trunk group switch config no aggreator group 2 gie gege ohna Iesel Netwerking Com mm Industrial Networking Corp 93 Disable the LACP switch config no aggreator lacp 1 IGS 3044GC User s Manual 6 5 Commands Set List VLAN command set vlan database Enter VLAN configure switch vlan database mode switch vlan vianmode 802 1q gvrp or switch vlan vianmode gvrp no vian V Disable vlan group by switch vlan no vlan 2 VID VID Disable GVRP switch vlan no gvrp V Assign a access link switch vlan vlan 802 19 port 3 PortNumber for VLAN by port if the access link untag 33 access link untag port belong to a trunk UntaggedVID group this command cant be applied vlan 8021q port V Assign a trunk link for switch vlan vlan 8021q port 3 PortNumber VLAN by port ifthe
13. systemlog E Display system log Switch gt show systemlog show systemlog Show system log switch show systemlog client amp server information no systemlog Disable systemlog switch config no systemlog functon smtp enable ER Enable SMTP function switch config smtp enable smtp serverip Configure SMTP switch config smtp serverip smip authentication Enable SMTP switch contig smtp authentication authentication Configure switch config smtp account User authentication account smtp password Configure switch config smtp password password authentication password Configure Rept e mail switch config smtp rcptemail Show the information switch show smtp smip rcptemail Index Email address ORing Industrial Networking Corp 104 Disable SMTP switch config no smtp IGS 3044GC User s Manual won event EE start Set cold start event switch config event Systemlog SMTP Both device cold start both event Set Authentication switch contig event authentication failure Systemlog SMTP Both failure event type authentication failure both event Set s ring topology _ switch config event O Ring topology change Systemlog SMTP Both changed event type __ ring topology change both event systemlog Link UP Link Down Bot h Set port event for switch config interface fastethernet system log 3 switch config if event systemlog both event smtp _ UP Link Down Bot Set port event for switch conftig interfa
14. the LED light on it means that the switch is the ring master of O Ring LED for Ring When the led light on it means the O Ring is activated LED for Fault Relay When the fault occurs the amber LED will be light on Console Port RJ 45 Reset button 10 100 1000Base T X Ethernet ports LED for 100M port link status 11 12 13 LED for 1000M port link status 100BaseF X 1000BaseX Combo Port LED for Combo port ORing Industrial Networking Corp 10 IGS 3044GC User s Manual 3 2 Front Panel LEDs O Ring has only One link Green Slowly blinking lack of one link to build the ring Fault relay Power failure or Amber Port down fail 10 100 1000Base T X Fast Ethernet E LNK ACT Green _ Data transmitted Gigabit Combo Ports LNK ACT Green Blinking Data transmitted ORing Industrial Networking Corp 11 IGS 3044GC User s Manual 3 3 Top view Panel The bottom panel components of IGS 3044GP GC Series are showed as below 1 Terminal block includes PWR1 PWR2 48V DC 2 Ground wire PWR 2 Fault PWR 1 rh 1A 24V V1 Vi DC12 48V ORing Industrial Networking Corp 12 IGS 3044GC User s Manual Cables 4 1 Ethernet Cables The IGS 3044GC switches have standard Ethernet ports According to the link type the switches use CAT 3 4 5 5e UTP cables to connect to any other network device PCs servers switches routers or hubs Please refer to the following table for cable specificatio
15. time traffic VLAN 802 1Q with VLAN tagging and GVRP supported IGMP Snooping for multicast filtering Software Features the Se Port configuration status statistics monitoring security SNTP for synchronizing of clocks over network Support PTP Client Precision Time Protocol clock synchronization DHCP Server Client support Port Trunk support MVR Multicast VLAN Registration support MRP O Ring Open Ring STP RSTP MSTP Network Redundancy ORing Industrial Networking Corp IGS 3044GC User s Manual Relay output for fault event alarming at Syslog server client to record and view events Warning Monitoring System da de i Include SMTP for event warning notification via email Event selection support RS 232 Serial Console Port RS 232 in RJ45 connector with console cable 9600bps 8 N 1 LED indicators Power Indicator Green Power LED x 3 R M Indicator Green Indicate system operated in O Ring Master mode Ring Indicator Green Indicate system operated in O Ring mode Fault Indicator Indicator Amber Indicate Amber Indicate unexpected event occurred event occurred Ee RJ45 port ae Green for port Link Act Amber for LOOMbps indicator indicator 100 1000Base X SFP Port Indicator Green for port Link Act Fault contact Faultcontact Power Physical Characteristic 74 3 W x109 2 D x153 6 H mm 2 93 x 4 3 x 6 05 inch Environmental Storage Temperature 40 to 85 C
16. to topology of network 5 1 1 6 Fast Recovery The Fast Recovery Mode can be set to connect multiple ports to one or more switches The TES 250 M12 with its fast recovery mode will provide redundant links Fast Recovery mode supports 5 priorities only the first priority will be the act port the other ports configured with other priority will be the backup ports Fast Recovery Mode E Active aain Hot incloded w emia Hot mchdel Port 04 included Fast Recovery Mode interface ORing Industrial Networking Corp 33 IGS 3044GC User s Manual The following table describes the labels in this screen Active Activate the fast recovery mode Port can be configured as 5 priorities Only the port with highest priority will be the active port 1st Priority is the highest Click Apply to activate the configurations 5 1 1 7 RSTP The Rapid Spanning Tree Protocol RSTP is an evolution of the Spanning Tree Protocol It provides faster spanning tree convergence after a topology change The system also supports STP and the system will auto detect the connected device that is running STP or RSTP protocol RSTP setting You can enable disable RSTP function and set parameters for each port RSTP Bridge Setting RSTP Mode Priority 0 61440 Max Age 6 40 Hello Time 1 10 Forward Delay Time 4 30 Priority must be a multiple of 4096 2 Forward Delay Time 1 should be greater than or equal to
17. transmitted with a length of between 512 and 1023 octes in clusive including those with error Total frames received and or transmitted with a length of between 1024 and MaxSize octes in clusive including those with error The lower 32 bit of the 64 bit OutOctets counter The sum of lengths of all Ethernet frames sent from this MAC The upper 32 bit of the 64 bit OutOctets counter The sum of lengths of all Ethernet frames sent from this MAC The number of frames sent that have an Unicast destination MAC address The number frames dropped in the transmit MAC because the frame experienced 16 consecutive collisions This counter is applicable in half duplex only and only of DiscardExcessive is one The number of good frames sent that have a Broadcast destination MAC address The total number of successfully transmitted frames that experienced exactly one collision This counter is applicable in half duplex only The number of good Flow Control frames sent The number of good Flow Control frames received The total number of successfully transmitted frames that experienced more than one collision This counter is applicable in 78 Oo en Ke IGS 3044GC User s Manual half duplex only Total frames received with a length of less than 64 octets but with a valid FCS Total frames received with a length of more than 64 octets and with a invalid FCS Total frames received with
18. 100BASE TX this function MRP Ring port Speed Duplex Will automatically change to Full mode us function used in combination Hirschmann Switch MRP because Hirschmann Switch MRP Ring port speed duplex always is Full mode 5 1 1 2 O Ring O Ring is the most powerful Ring in the world The recovery time of O Ring is less than 10 mS It can reduce unexpected damage caused by network topology change O Ring supports three Ring topologies O Ring Coupling Ring and Dual Homing O Ring E Enable Ring Master 1st Ring Port LINKDOWN 2nd Ring Port LINKDOWN E Enable Couple Ring couple Port LINKDOWN E Enable Dual Homing Homing Port LINKDOWN O Ring interface The following table describes the labels in this screen Enable Ring Mark to enable Ring ORing Industrial Networking Corp 29 IGS 3044GC User s Manual Enable Ring Master There should be one and only one Ring Master in a ring However if there are two or more switches which set Ring Master to enable the switch with the lowest MAC address will be the actual Ring Master and others will be Backup Masters 17 Ring Port The primary port when this switch is Ring Master 2 Ring Port The backup port when this switch is Ring Master Enable Coupling Ring Mark to enable Coupling Ring Coupling Ring can be used to divide a big ring into two smaller rings to avoid effecting all switches when network topology change It is a good applicati
19. 40 to 185 F Operating Temperature 40 to 70 C 40 to 158 F Operating Humidity 5 to 95 Non condensing Regulatory approvals EMI FCC Part 15 CISPR EN55022 class A EN61000 4 2 ESD EN61000 4 3 RS EN61000 4 4 EFT EN61000 4 5 Surge EN61000 4 6 CS EMS EN61000 4 8 EN61000 4 11 MTBF 214 978 hours Warranty 5 years ORing Industrial Networking Corp 1
20. Allow List Delete p MAC Port 5 Apply Ge i RL a 0 IP Guard Allow List State interface The following table describes the labels in this screen IP address of the allowed entry MAC address of the allowed entry Pot Port number of the allowed entry If you doubt some allowed IP traffic are abnormal you could block the traffic use this field Active Allow the IP traffic Suspend Block the IP traffic If you want to delete the entry please check this box and apply it IP Guard Super IP List IP Guard is an intelligent and easy use function for IP security It could protect the network from unknown IP the IP not in allowed list attack The illegal IP traffic will be blocked This page allows you to configure IP Guard Super IP list Super IP entry has a special priority the IP has no limited of MAC address and port binding Any IP traffic are allowed when the IP is in the Super IP list ORing Industrial Networking Corp 69 IGS 3044GC User s Manual IP Guard Super IP List IPAddress super IP List IP Address IP Guard Super IP List State interface IP Guard Super IP List IP Guard is an intelligent and easy use function for IP security It could protect the network from unknown IP the IP not in allowed list attack The illegal IP traffic will be blocked IP Guard Monitor List Add to Allow List Port O 192 168 10 66 001E94988989 19700103 19 20 sa The fo
21. C interface static switch config if no mac address table static hwaddr 000012345678 no mac address table Remove an entry of _ switch config no mac address table MAC address table filter hwaddr 000012348678 filter no mac address table Remove dynamic switch config no mac address table entry of MAC address table 6 10 Commands Set List SNMP command set snmp agent mode Select the agent mode switch config snmp agent mode of SNMP viv2c viv2c v3 k snmp server host Configure SNMP switch config snmp server host IP address community server host 192 168 10 50 community public information and trap version v1 Community string community string remove trap version Switch config ORing Industrial Networking Corp 99 IGS 3044GC User s Manual v1 v2c no snmp server host 192 168 10 50 snmp Configure the switch config snmp community strings community string right community strings public right RO Community string or right switch config snmp RO RW community strings public right RW snmp snmpv3 user Configure the switch config Ssnmp snmpv3 user User Name userprofile for test01 password AuthPW PrivPW password SNMPV3 agent Authentication Privacy password Password Privacy could be empty Password Show SNMP switch show snmp configuration show snmp server Show specified trap switch show snmp server server information no snmp Remove the specified switch config no snmp commun
22. DHCP client function through IP configuration IP Setting DHCP Client Disable IP Address 192 168 10 1 Siam EA 255 255 255 Gateway 19 168 10 254 IP Configuration interface The following table describes the labels in this screen Description DHCP Client To enable or disable the DHCP client function When DHCP client function is enabling the switch will be assigned the IP address from the network DHCP server The default IP address will be replaced by the IP address which the DHCP server has assigned After clicking Apply button a popup dialog shows up to inform when the DHCP client is enabling The current IP will lose and you should find a new IP on the DHCP server IP Address Assign the IP address that the network is using If DHCP client function is enabling you do not need to assign the IP address ORing Industrial Networking Corp 20 IGS 3044GC User s Manual The network DHCP server will assign the IP address for the switch and it will be display in this column The default IP is 192 168 10 1 Assign the subnet mask of the IP address If DHCP client function is enabling you do not need to assign the subnet mask Gateway Assign the network gateway for the switch The default gateway is 192 168 10 254 Assign the primary DNS IP address DNSZ Assign the secondary DNS IP address Apply Click Apply to activate the configurations 5 1 4 4 Time Setting This page includes configurations
23. Disable disable SYSLOG Client Only log to local system Server Only log to a remote SYSLOG server Both log to both of local and remote server SYSLOG Server IP The remote SYSLOG Server IP address Address Apply Click Apply to set the configurations System Warning SMTP Setting The SMTP is Short for Simple Mail Transfer Protocol It is a protocol for e mail transmission across the Internet Please refer to RFC 821 Simple Mail Transfer Protocol SMTP Setting E mail Alert Enable ze iv WT eee 12 1650 10 66 Mail Subject Automated Email Alert Sender E Authentication Rcpt e mail Address 1 Rcpt e mail Address 2 Rcpt e mail Address 3 Rcpt e mail Address 4 System Warning SMTP Setting interface The following table describes the labels in this screen Ems Aen Enable Disable transmission system warning events by e mail SMTP Server IP Address Setting up the mail server IP address Mail Subject The Subject of the mail ORing Industrial Networking Corp 72 IGS 3044GC User s Manual Sender Set up the email account to send the alert Authentication a Username the authentication username WR Password the authentication password 8 Confirm Password re enter password Recipient E mail Address The recipient s E mail address It supports 6 recipients for a mail Apply Click Apply to set the configurations System Warning Event Selection SYSLOG and SMTP ar
24. Link Both Access Link and Trunk Link are available Hybrid QinQ Link enable QinQ mode gt allow you to insert ORing Industrial Networking Corp 50 IGS 3044GC User s Manual one more VLAN tag in a original VLAN frame Untagged VID Set the port default VLAN ID for untagged devices that connect to the port The range is 1 to 4094 Tagged VIDs Set the tagged VIDs to carry different VLAN frames to other switch Apply Click Apply to set the configurations 5 1 4 2 VLAN Setting Port Based Packets can go among only members of the same VLAN group Note all unselected ports are treated as belonging to another single VLAN If the port based VLAN enabled the VLAN tagging is ignored VLAN Setting VLAN Operation Mode Port Based VLAN List VLAN Configuration Port Base interface 1 The following table describes the labels in this screen Click add to enter VLAN add interface Edit exist VLAN ORing Industrial Networking Corp 51 IGS 3044GC User s Manual VLAN Setting VLAN Operation Mode VLAN ID E e ze VLAN Configuration Port Base interface 2 The following table describes the labels in this screen Ada ack le group Apply Click Apply to set the configurations ORing Industrial Networking Corp 32 IGS 3044GC User s Manual 5 1 5 Traffic Priorilization Traffic Prioritization includes 3 modes port base 802 1p COS and TOS DSCP By traffic prioritization
25. List System Commands Gei 88 6 3 Commands Set List Port Commands Get 90 6 4 Commands Set List Trunk Command eet 93 6 5 Commands Set List VLAN Command eet e 94 6 6 Commands Set List Spanning Tree command eet 95 6 7 Commands Set List QoS command eet 97 6 8 Commands Set List IGMP command eet 98 6 9 Commands Set List MAC Filter Table command eet 99 6 10 Commands Set List SNMP command eet 99 6 11 Commands Set List Port Mirroring command sei 100 6 12 Commands Set List 802 1x command eet 101 6 138 Commands Set List TFTP command eet 103 6 14 Commands Set List SYSLOG SMTP EVENT command set 008 104 6 15 Commands Set LiSt SNTP command eet 106 6 16 Commands Set List O Ring command eet 107 technical SO Ee e de E 0 ORing Industrial Networking Corp 4 IGS 3044GC User s Manual Getting to Know Your Switch 1 1 About the IGS 3044GC Managed Industrial Switch The IGS 3044GCseries are powerful managed industrial switches with many features These switches can work under wide temperature dusty environment and humid condition The IGS 3044GCcan be managed by WEB TELNET Consol or other third party SNMP software as well Besides these switches can be managed by a useful utility that we called Super view Open Vision is powerful network management software With its friendly and powerful interface you can easily configure multiple switches at the same time and monitor s
26. Set timezone index switch config sntp timezone 22 Timezone use show sntp timzezone command to get more information of index show sntp timezone ORing Industrial Networking Corp 106 Show SNTP switch show snip Information Show index number of switch show sntp timezone time zone list Disable SNTP switch config no sntp sntp daylight offset offset of daylight switch config sntp daylight offset 3 Minute saving time if SNTP function is inactive this command can t be nosntp IGS 3044GC User s Manual o f po S no sntp daylight e Disable daylight switch contig no sntp daylight saving time 6 16 Commands Set List O Ring command set Enable ring master _ switch config ring master Enable couple ring _ switch config ring couplering Enable dual homing switch contig ring dualhoming Ring ringport Configure 1st 2nd switch config ring ringport 7 8 1st Ring Port 2nd Ring Port Ring couplingport Configure Coupling switch config ring couplingport 1 Coupling Port Port Ring Port Ring homingport Configure Dual switch config ring homingport 3 Dual Homing Port Homing Port Show the information switch show ring of O Ring Disable dual homing _ switch config no ring dualhoming no Ring couplering no Ring dualhoming Ring controlport Configure Control Port switch config ring controlport 2 Control Port ORing Industrial Networking Corp 107 Technical Specificati
27. TE TT re aen 5 1 10 6 Traffic Monitor The function can monitor switch Traffic If traffic is too large Switch will sent SYSLOG Event or SMTP Mail Traffic Monitor Time Interval ASIA System event log interface Monitored Counter Increasing Quantity The following table describes the labels in this screen Monitored Counter Select monitor type Time Interval Setting Interval time Increasing Quantity Setting alarm Quantity Event Alarm Select alarm function SYSLOG or SMTP ORing Industrial Networking Corp 80 IGS 3044GC User s Manual 5 1 10 7 Ping Ping function allows the switch to send ICMP packets to detect the remote notes Ping IP Address Ping Log Pinging 192 168 10 66 seq 1 sent Reply seq 1 from 192 168 10 66 Pinging 192 168 10 66 seq 2 sent Reply seg 2 from 192 168 10 66 Pinging 192 168 10 66 seq 3 sent Reply seg 3 from 192 168 10 66 Pinging 192 168 10 66 seq 4 sent Reply seq 4 from 192 168 10 66 Ping complete sent 4 received 4 Ping interface The following table describes the labels in this screen IP Address Enter the IP address that you want to detect Active Click Active to send ICMP packets 5 1 11 Save Configuration If any configuration changed Save Configuration should be clicked to save current configuration data to the permanent flash memory Otherwise the current configuration will be lost when power off or system rese
28. TP calculations Inthe event of a loop spanning tree considers the path cost when selecting an interface to place into the forwarding state ORing Industrial Networking Corp 96 IGS 3044GC User s Manual stp path priority Port Priority switch config if stp path priority 127 stp admin p2p i switch config interface fastEthernet Auto True False iori i 2 switch config if stp admin p2p Auto stp admin edge i switch config interface fastEthernet True False iori i 2 switch config if stp admin edge True stp admin non stp i switch config interface fastEthernet True False iori i 2 switch config if stp admin non stp False Show spanning tree no spanning tree 6 7 Commands Set List QoS command set qos policy Select QOS policy switch config qos policy weighted fair strict scheduling weighted fair qos prioritytype Setting of QOS switch config qos prioritytype port based cos only tos priority type ORing Industrial Networking Corp 97 IGS 3044GC User s Manual onlylcosfirsttossirst TL qos priority portbased Configure Port based switch config qos priority portbased Port lowest low middle high qos priority cos Configure COS switch config qos priority cos 22 Priority lowest low mid Priority middle dle high qos priority tos Configure TOS switch config qos priority tos 3 high Priority lowest low mid Priority dle high Display the switch gt show qos informa
29. a VLAN Bridge Lesser Configuration Name The same MST Region must have the same MST configuration SS gegen Revision Level The same MST Region must have the same revision level ogee Priority 0 61440 A value used to identify the root bridge The bridge with the lowest value has the highest priority and is selected as the root If the value changes You must reboot the switch The value must be multiple of 4096 according to the protocol standard rule Max Age Time 6 40 The number of seconds a bridge waits without receiving Spanning tree Protocol configuration messages before attempting a reconfiguration Enter a value between 6 through 40 Hello Time 1 10 The setting follow the rule below to configure the MAX Age Hello ORing Industrial Networking Corp 38 IGS 3044GC User s Manual Time and Forward Delay Time at controlled switch sends out the BPDU packet to check RSTP current status Enter a value between 1 through 10 2 x Forward Delay Time value 1 2 Max Age value 2 2 x Hello Time value 1 Forwarding Delay The number of seconds a port waits before changing from its Time 4 30 Rapid Spanning Tree Protocol learning and listening states to the forwarding state Enter a value between 4 through 30 Max Hops 1 40 This parameter is additional to those specified for RSTP A single value applies to all Soanning Trees within an MST Region the CIST and all MSTIs for which the Bridge is the Regional Root Apply
30. a length of more than MaxSize octets Oversize but with a valid FCS Jabb Total frames received with a length of more than MaxSize octets abber but with an invalid FCS InMACRcvErr Total frames received with an RxErr signal from the PHY Jabber or RxErr The number of collision events seen by MAC not including those Collisions conted in Single Multiple Excessive or Late This counter is applicable in half duplex only The number of times a collision is detected later than 512 Late bits times into the transmission of a frame This counter is applicable in half duplex only 5 1 10 5 Port Monitoring Port monitoring function supports TX egress only RX ingress only and both TX RX monitoring TX monitoring sends any data that egress out checked TX source ports to a selected TX destination port as well RX monitoring sends any data that ingress in checked RX source ports out to a selected RX destination port as well as sending the frame where it normally would have gone Note that keep all source ports unchecked in order to disable port monitoring Destination Port Source Port Port No Port 01 Port 02 Port 03 Port 04 Port monitoring interface ORing Industrial Networking Corp 79 IGS 3044GC User s Manual The following table describes the labels in this screen Destination Port The port will receive a copied frame from source port for M e Source Port The port will be monitored Mark the blank of TX or RX to be
31. ce Industrial Managed Ethernet Switch Open all Ei Ed om e om om sm om com om E System Information Front Panel Basic Setting Redundancy Multicast Port Setting VLAN Traffic Prioritization DHCP Server Relay SNMP Security Warning Monitor and Diag Save Configuration Factory Default System Reboot Logout System Information IGS 3044GC Industrial 8 port managed Gigabit Ethernet Sy eC a a switch with 4x10 100 1000Base T X and 4xGigabit combo ports SFP socket System Location xe System Contact a SNMP OID Firmware Version System Name 1 3 6 1 4 1 25972 100 0 0 21 Kernel Version MAC Address 00 1E 94 06 01 EA System Uptime 0 Day s 2 Hour s 2 Min s 32 Sec s Main interface ORing Industrial Networking Corp 17 IGS 3044GC User s Manual 5 1 2 System Information System Name 1G5 30446C Industral 8 port managed Gigabit Ethernet ACL e d ge witch with 4x10 100 1000Base T X and 4xGigabrt combo ports SFP socket System Location System Contact SNMP OID 1 3 6 1 4 1 25972 100 0 0 21 Firmware Version Kernel Version MAC Address O0 1E 94 06 01 EA System Uptime 0 Day s 2 Hour s 3 Mints 4 Sec s System Information interface System Information The system information will display the configuration of Basic Setting Switch Setting page Enable Location Alert When click Enable Location Alert pwR1 PWR2 and PWR3 LEDs of the switch will start to flash together an
32. ce fastethernet SMTP 3 switch config if event smtp both show event Ip Show event selection switch show event device cold start no event Disable cold start switch config no event Teee cold start Disable Authentication iswitch come no event Disable O Ring switch config no event no event authentication failure no event O Ring topology change topology changed ring topology change event type no event systemlog Disable port event for switch config interface fastethernet 3 switch config if no event systemlog no event smpt Disable port event for switch config interface fastethernet 3 switch config if no event smtp show systemlog Show system log switch show systemlog client amp server information ORing Industrial Networking Corp 105 IGS 3044GC User s Manual 6 15 Commands Set List SNTP command set sntp enable Enable DECHE function switch config sntp enable sntp daylight Enable cali saving switch config sntp daylight time if SNTP function IS Inactive this command can t be sntp daylight period Set period of daylight switch config sntp daylight period Start time End time saving time if SNTP 20060101 01 01 20060202 01 01 function is inactive this command cant be applied Parameter format yyyymmdd hh mm snip ip Set SNTP server IP if switch config sntp ip 192 169 1 1 SNTP function is inactive this IP command can t be snip timezone
33. ce ingress switch config interface limit frame type to fastEthernet 2 accept all frame switch config if bandwidth type all bandwidth type Set interface ingress switch config interface broadcast multicast floo limit frame type to fastEthernet 2 ded unicast accept broadcast switch config if oandwidth type multicast and flooded broadcast multicast flooded unicast unicast frame bandwidth type Set interface ingress switch config interface broadcast multicast limit frame type to fastEthernet 2 accept broadcast and switch config if boandwidth type multicast frame broadcast multicast bandwidth type Set interface ingress switch config interface broadcast only limit frame type to fastEthernet 2 only accept switch config if oandwidth type broadcast frame broadcast only bandwidth in Value Set interface input switch config interface bandwidth Rate fastEthernet 2 Range is from 100 switch conftig if boandwidth in 100 kbps to 102400 kbps or to 256000 kbps for ORing Industrial Networking Corp 91 IGS 3044GC User s Manual bandwidth out Value Set interface output Sswitch config interface bandwidth Rate fastEthernet 2 Range is from 100 switch config if bandwidth out 100 kbps to 102400 kbps or to 256000 kbps for giga ports and zero means no limit show bandwidth Show interfaces switch config interface bandwidth control fastEthernet 2 switch config if show bandwidt
34. creen To get the newest event logs and refresh this page 5 1 10 2 MAC Address Table Refer to IEEE 802 1 D Sections 7 9 The MAC Address Table that is Filtering Database supports queries by the Forwarding Process as to whether a frame received by a given port with a given destination MAC address is to be forwarded through a given potential transmission port MAC Address Table Port No ALL el MAC Address Static 0011223534455 Port 06 Dynamic DOLES4986989 Port 06 Static Q100S5E000006 Port 05 Dynamic Address Count 1 Static Address Count 2 Flush Table Help MAC Address Aging Setting MAC Address Aging Time 5 min w Auto Flush Table When Ports Link Down MAC Address Auto Learning ze MAC Address Table interface The following table describes the labels in this screen Port NO gt Show all MAC addresses mapping to a selected port in table Flush MAC Table Clear all MAC addresses in table MAC Address Aging Assign aging time MUST be multiple of 15 ORing Industrial Networking Corp 75 IGS 3044GC User s Manual Auto Flush Table Enable this function when port link down switch will Flush MAC When Ports Link table Down MAC Address Auto Enable or Disable MAC Learning function Learning Apply Click Apply to set the configurations 5 1 10 3 Port Overview Port statistics show several statistics counters for all ports Port Overview TX TX RX RX TX Port No Typ
35. d click Disable Location Alert the LEDs will stop flashing 5 1 3 Front Panel Show the panel of IGS 3044GC Click Close to close panel on web ORing ORing Industrial Networking Corp 18 IGS 3044GC User s Manual 5 1 4 Basic setting 5 1 4 1 Switch Setting System Setting System Name 15 3044 GC SV pisces iene dustrial H Get managed Gigakit Ethemet switch with 4x101 00 1 O00Rase T 2s and det gesat System Contact ze Switch setting interface The following table describes the labels in this screen System Name Assign the name of switch The maximum length is 64 bytes System Description Display the description of switch System Location Assign the switch physical location The maximum length is 64 bytes System Contact Enter the name of contact person or organization 5 1 4 2 Admin Password Change web management login username and password for the management security issue Admin Password User Name New Password Confirm Password IT Admin Password interface ORing Industrial Networking Corp 19 IGS 3044GC User s Manual The following table describes the labels in this screen User name Key in the new username The default is admin New Password Key in the new password The default is admin Confirm password Re type the new password Apply Click Apply to activate the configurations 5 1 4 3 IP Setting You can configure the IP Settings and
36. d to identify the root bridge The bridge with the lowest value has the highest priority and is selected as the root If the value changes You must reboot the switch The value must be multiple of 4096 according to the protocol standard rule Apply Click Apply to activate the configurations ORing Industrial Networking Corp 40 IGS 3044GC User s Manual MSTP Instance Port Instance Priority Path Cost 0 240 1 200000000 0 Auto o Priority must be a multiple of 16 MSTP Instance Port interface Description Set the instance s information except CIST Selecting the port that you want to configure Priority 0 240 Decide which port should be blocked by priority in LAN Enter a number 0 through 240 The value of priority must be the multiple of 16 Path Cost The cost of the path to the other bridge from this transmitting 1 200000000 bridge at the specified port Enter a number 1 through 200000000 Apply Click Apply to set the configurations ORing Industrial Networking Corp 4 IGS 3044GC User s Manual 5 1 2 Multicast 5 1 2 1 IGMP Snooping Internet Group Management Protocol IGMP is used by IP hosts to register their dynamic multicast group membership IGMP has 3 versions IGMP v1 v2 andv3 Please refer to RFC 1112 2236 and 3376 IGMP Snooping improves the performance of networks that carry multicast traffic It provides the ability to prune multicast traffic so that it travels only t
37. ds Set List System Commands Set pense Ire ample Show switch switch gt show config ee i aie show terminal Show console switch show terminal UE E write memory Save your switch write memory configuration into permanent memory flash rom system name Configure system switch config system name xxx Geen JE system location Set switch system switch config system location xxx Geen Ess system description Set switch system switch config system description Set switch system switch config system contact xxx Show system switch gt show system info System Description system contact System Contact show system info information ip address Configure the IP switch config ip address lp address address of switch 192 168 1 1 255 255 255 0 Subnet mask 192 168 1 254 Gateway Enable DHCP client switch config ip dhcp na Show IP information of switch show ip SS Disable DHCP client switch config no ip dhcp Se ee Halt and perform a switch config reload cold restart ORing Industrial Networking Corp 88 no ip dhcp reload IGS 3044GC User s Manual gebaut G Restore to default Switch config default admin username Changes a login switch config admin username Username username XXXXXKX maximum 10 words admin password Specifies a password switch config admin password in S Show administrator switch show admin ne dhcpserver enable o Enable DHCP Server switch config dhcpserver
38. dwidth Rate Limit Port No Ingress Limit Frame Type Ingress Egress reng bps 0 wes Port 02 Rate Limit interface ORing Industrial Networking Corp 46 IGS 3044GC User s Manual The following table describes the labels in this screen Ingress Limit Frame You can set all Broadcast only Broadcast Multicast Type or Broadcast Multicast Flooded Unicast mode Ingress The switch port received traffic Egress The switch port transmitted traffic Apply Click Apply to activate the configurations 5 1 3 5 Port Trunk Port Trunk Setting You can select static trunk or 802 3ad LACP to combine several physical links with a logical link to increase the bandwidth Port Trunk Setting Port No Group ID Type Port 06 Ww Port 07 Port 08 802 3ad LACP Work Ports Group ID Work Ports Trunki Trunk Trunks Trunk4 Port Trunk Setting interface ORing Industrial Networking Corp 47 IGS 3044GC User s Manual The following table describes the labels in this screen Select port to join a trunk group Support static trunk and 802 3ad LACP Work Port Select the number of active ports in dynamic group LACP The default value of works ports is maximum number of the group If the number is not maximum number of ports the other inactive ports in dynamic group will be suspended no traffic Once the active port is broken the suspended port will be active automatically Appl
39. e Link State Good Bad Good Bad Abort Packet Packet Packet Packet Packet WEEN 100TX Port 02 WER oer Packet Collision Port Overview interface The following table describes the labels in this screen RX GOOD Packet The number of good packets received by this port ORing Industrial Networking Corp 76 IGS 3044GC User s Manual 5 1 10 4 Port Counters This page shows statistic counters for the port The Clear button is to reset all counters to zero for all ports Port No InGoodOctetsLo InGoodOctetsHi InBadOctets OutFCSErr See eee See aaa InUnicasts Deferred InBroadcasts InMulticasts Octets64 Octets12 7 Octets255 Octets511 Octets1023 OctetsMax OutOctetsLo OutOctetsHi WEE NES BE OutUnicasts Excessive OutMulticasts OutBroadcasts es ee 0 i OutPause InPause Multiple WEE NES BE Undersize Fragments Oversize InMACRcvErr InFCSErr Collisions Late ll Port Counters interface The following table describes the labels in this screen The lower 32 bits of the 64 bit InGoodOctets counter The sum of InGoodOctetsLo lengths of all good Ethernet frames received that is frames that are not bad frames The upper 32 bits of the 64 bit InGoodOctets counter The sum of InGoodOctetsHi lengths of all good Ethernet frames received that is frames that are not bad frames InBadOctets The sum of lengths of all bad Ethernet frames received The number of frames transmitted with a invalid FCS Whenever
40. e eee eee ee ee ee ee E E ee E 15 4 3 Console Cab 6 ege acncnensecnnacneaaeeammsensqcanonazncatenctocateastonaieeatenatoaacaneasatenseceatehs 15 WEB Elle SING ING EE 16 5 1 Configuration Dy Web Ee EE 16 5 1 1 About Web based Management 16 EE MOMA O EE 18 Dale ROME D ne 18 Dee ASIC FS ale DEE 19 5 1 4 1 MEET 19 vie GAOMI PASS WONG WEE 19 DLRAS AR e EE 20 Sled TWINS SOG ees cxczsecscncastcasewscsensesseecaqetactdasdteastesbicatinatiasttecseathadeed 21 e Fev Bc mmm RE 25 ee E MOODUS TOP EE 25 ILAT AWOFTOV SION EE 26 SAG BACKUP amp ROSON sonona S 26 5 1 4 9 Upgrade Firmware oeer a ees 28 ORing Industrial Networking Corp 2 IGS 3044GC User s Manual E a I e 0 le EE 28 Gan n KE MR EE 28 een EE EE e ee DEN 29 DERS OREN RIN E 30 Slut SOCR e DE 32 SLES RSP Repeal E r a e eae 33 SERLO FISE ee ONY EE 33 Sleek GE 34 517k Ga GE 37 e EE Ee EN 42 5 1 2 1 IOMP SNOOP DEE 42 Dea e EE 43 See Staic Muticast PINGING sizer AATA 44 DA FPO A a nn ee ee ee nh ee ee een eee eRe eee 45 5 1 3 1 Belag CORON EE 45 Sloe Ge e 46 Siero ROAIT yanbsannactoan neat onne ante sats nabeansetieasdaaaasanaaiataneiananadaaaiaassaneiaaaunnenateane 46 Oats MAO Bin 46 DESO Te e nee Tu 47 Ska O LOOP GUGIGiea eee eee 49 514 VEAN ME 49 Sua VLAN Seting IEEE 902 Le GE 49 al A 2 VELAN Setting Form Based ie a ee 51 Sa Eh 53 Dalol QOS ae e EE 53 Skoz FROM DASS PION E 54 51593 COSBOZ e E 54 ef Poke a ho D sc deere ree er eee
41. e labels in this screen MAC Address Input MAC Address to a specific port Select port of switch Add an entry of MAC and port information Delete Delete the entry Show help file 5 1 8 3 MAC Blacklist MAC Blacklist can eliminate the traffic forwarding to specific MAC addresses in list Any frames forwarding to MAC addresses in this list will be discarded Thus the target device will never receive any frame MAC Address MAC Address OO1E94123456 MAC Blacklist interface ORing Industrial Networking Corp 64 IGS 3044GC User s Manual The following table describes the labels in this screen MAC Address Input MAC Address to add to MAC Blacklist Add an entry to Blacklist table EEN Help eee 5 1 8 4 802 1x 802 1x Radius Server 802 1x makes the use of the physical access characteristics of IEEE802 LAN infrastructures in order to provide a authenticated and authorized devices attached to a LAN port Please refer to IEEE 802 1X Port Based Network Access Control 802 1x Radius Server Radius Server Setting 802 1x Protocol Enable w Radius Server IP ECH Server Port Accounting Port AE Shared Key 12545676 NAS Identifier NAS L SWITCH Advanced Setting Quiet Period TX Period Supplicant Timeout Server Timeout Max Requests Re Auth Period ze 802 1x Radius Server interface ORing Industrial Networking Corp 65 IGS 3044GC User s Manual The following table describ
42. e the two warning methods that supported by the system Check the corresponding box to enable system event warning method you wish to choose Please note that the checkbox can not be checked when SYSLOG or SMTP is disabled Event Selection system Event Event Type Syslog Device cold start Device warm start Authentication failure ja O Ring topology change Tris Port Event Link Down Disable Disable Link Up amp Link Down ze System Warning Event Selection interface The following table describes the labels in this screen a peame S Device cold start When the device executes cold start the system will issue a log event Device warm start When the device executes warm start the system will issue a ORing Industrial Networking Corp 73 IGS 3044GC User s Manual maen Authentication Failure Alert when SNMP authentication failure O Ring topology change Alert when O Ring topology changes Port Event Disable Link Up Link Down Link Up amp Link Down Apply Click Apply to set the configurations 5 1 10 Monitor and Diag 5 1 10 1 System Event Log If system log client is enabled the system event logs will be shown in this table system Event Log 2 Jan 3 19 35 12 SYSLOG Server 92 168 LO L Jan 3 1935 12 SYSLOG Enable Fagel v System event log interface ORing Industrial Networking Corp 74 IGS 3044GC User s Manual The following table describes the labels in this s
43. e updating make sure you have your TFIP server ready and the firmware image and configuration file is on the TFTP server Auto Provision L Auto install configuration file from TFTP server TEID Server ID Addrese 19 1765 10 66 Configuration File Name Auto install firmware image file from TFTP server TEID Server ID Addrese 192 1690 10 66 Firmware File Name Apply Help Auto Provision interface 5 1 4 8 Backup amp Restore You can save current EEPROM value from the switch to TFTP server then go to the TFTP restore configuration page to restore the EEPROM value Restore Configuration From TFTP Server TFTP Server IP Address KSC Restore File Name From Local PC iow ORing Industrial Networking Corp 26 IGS 3044GC User s Manual Backup Configuration To TFTP Server TFTP Server IP Address 4a aU Backup File Name data bin To Local PC Backup Backup amp Restore interface The following table describes the labels in this screen TFTP Server IP Address Fill in the TF TP server IP Restore File Name Fill the file name Restore Click restore to restore the configurations Form Local PC User can select file restore not need TFTP server Restore File Name Fill the file name Click restore to restore the configurations Click backup to backup the configurations To Local PC User can download config file to switch not need TF TP server ORing Industrial
44. el The DIN Rail kit helps switch to fix on the DIN Rail It is easy to install the switch on the DIN Hal 2 1 1 Mount IGS 3044GCSERIES on DIN Rail ODOOOOO 33 6 DIN Rail Size ORing Industrial Networking Corp IGS 3044GC User s Manual 2 2 Wall Mounting Installation Each switch has another installation method for users to fix the switch A wall mount panel can be found in the package The following steps show how to mount the switch on the wall NS 65 95 seg Wall Mounting size ORing Industrial Networking Corp 8 Hardware Overview 3 1 Front Panel The following table describes the labels that stick on the IGS 3044GP GC series 10 100 1000 4 10 100 1000Base T X RJ 45 fast Ethernet ports support Base T X Ru 45 auto negotiation fast Ethernet Default Setting ports Speed auto Duplex auto Flow control disable Gigabit SFP Ports 1000Base X on SFP port for GS 3044GP Gigabit Combo 4 0 100 1000Base T X RJ 45 100 1000Base X SFP Ports Ports Use RS 232 with RJ 45 connecter to manage switch ORing Industrial Networking Corp E o MONDO IGS 3044GC User s Manual IGS 3044GC 1 2 13 P7 LINK ACT l 3 4 9 6 E T P5 LINK ACT 8 11 10 9 LED for PWR When the any PWR ON the green led will be light on LED for PWR1 When the PWR2 links the green led will be light on LED for PWR2 When the PWR3 links the green led will be light on LED for R M Ring master When
45. enable dhcpserver lowip dhcpserver lowip dhcpserver highip dhcpserver subnetmask Subnet mask dhcpserver gateway dhcpserver dnsip dhcpserver leasetime Configure low IP switch config ree eo Configure high IP switch contig dhcpserver highip Configure subnet switch config dhcpserver ee neoon 255 255 255 0 Configure gateway for switch config dhcpserver gateway Configure DNS IP for switch config dhcpserver dnsip Configure lease time switch config dhcpserver Set static IP for DHCP switch config interface Hours dhcpserver ipbinding IP address show dhcpserver configuration show dhcpserver clients show dhcpserver clients by port fastEthernet 2 switch config if dhcpserver lpbinding 192 168 1 1 Show configuration of switch show dhcpserver Show client entries of switch show dhcpserver clinets i ae Show IP Binding switch show dhcpserver ip binding information of DHCP ip binding server Disable DHCP server switch config no dhcpserver security enable Enable IP security switch contig security enable nae security http Enable IP security of switch config security http ORing Industrial Networking Corp 89 no dhcpserver IGS 3044GC User s Manual Enable IP security of switch config security telnet telnet server Set the IP security list switch config security ip 1 192 168 1 55 Show the information switch show security i Disable IP security switch confi
46. es the labels in this screen 802 1x Portocol Enable or Disable 802 1X Radius Server function Radius Server IP The IP address of the authentication server authenticate Radius Server Shared Key A key shared between this switch and authentication server Advanced Setting Quiet Period Set the time interval between authentication failure and the start of a new authentication attempt Tx Period Set the time that the switch can wait for response to an EAP Tet stats ete tare an EAP request Server Timeout Set the period of time the switch waits for a Radius server response Iessen supplicant Re Auth Period Set the period of time after which clients connected must be re authenticated Apply Click Apply to set the configurations 802 1x Port Authorized Mode Set the 802 1x authorized mode of each port NAS Identifier A string used to identify this switch 802 1x Port Authorize Setting Port No Port Authorize Mode nm BS RER ES Port 03 fo a E yy E gd Port 04 802 1x Port Authorize interface ORing Industrial Networking Corp 66 IGS 3044GC User s Manual The following table describes the labels in this screen Port Authorized Mode Reject force this port to be unauthorized Accept force this port to be authorized Authorize the state of this port was determined by the outcome of the 802 1x authentication Disable this port will not participate in 802 1x Apply Click Apply to set t
47. et frames Tag contains a VLAN Identifier VID that indicates the VLAN numbers You can create Tag based VLAN and enable or disable GVRP protocol There are 256 VLAN groups to provide configure Enable 802 1Q VLAN the all ports on the switch belong ORing Industrial Networking Corp 49 IGS 3044GC User s Manual to default VLAN VID is 1 The default VLAN cannot be deleted GVRP allows automatic VLAN configuration between the switch and nodes If the switch is connected to a device with GVRP enabled you can send a GVRP request by using the VID of a VLAN defined on the switch the switch will automatically add that device to the existing VLAN VLAN Setting VLAN Operation Mode GVRP Mode Management VLAN ID Port VLAN Setting Port No Link Type PVID Untagged VIDS Tagged VIDs ronn ESCHEID BEE ron ESCHEID BEE VLAN Configuration 802 1Q interface The following table describes the labels in this screen VLAN Operation Mode GVRP Mode Enable Disable GVRP function Management VLAN ID Management VLAN can provide network administrator a secure VLAN to management Switch Only the devices in the management VLAN can access the switch Pot Select the port to configure Link type There are 3 types of link type Access Link single switch only allows you to group ports by setting the same VID Trunk Link extended application of Access Link allows you to group ports by setting the same VID with 2 or more switches Hybrid
48. ffic to the ports that are connected to registered end stations static Multicast Filtering Multicast IP Address Po Member Ports Port 01 Port o2 Port o3 Port o4 1 Port 05 Port o6 Port o7 L Port 08 IP Address Member Ports 230 0 0 1 Port 06 Port 0 Multicast Filtering Interface The following table describes the labels in this screen IP Address Assign a multicast group IP address in the range of 224 0 0 0 239 255 255 255 Member Ports Tick the check box beside the port number to include them as the member ports in the specific multicast group IP address Show current IP multicast list Delete an entry from table ORing Industrial Networking Corp 44 IGS 3044GC User s Manual 5 1 3 Port Setting 5 1 3 1 Port Control By this function you can set the state speed duplex flow control and security of the port Port Control Port No State Speed Duplex Flow Control Security Port 01 ble AntoNegotiation Syrumetic Drake E Port 02 a Anteblesotation SYTOTWEHIC s Symmetric w Port 03 ZGutkchleactiatcn E BEL E D I lt iI lt a a lt i lt I lt unt Port 04 Antoegoatiaton E s Antoesatiation amptrie T lt Port 05 4 T s Antoegatation Syramenic Antoesatation bam Port 06 J fy Ee Ee Ee T 4 T lt Port 07 A E Ee T T lt Port 08 s Antoesatation kam
49. function you can classify the traffic into four classes for differential network application IGS 3044GP GC series support 4 priority queues 5 1 5 1 Qos policy Policy QoS Mode QoS Policy Use an 8 4 2 1 weighted fair queuing scheme Use a strict priority scheme ze Traffic Prioritization interface The following table describes the labels in this screen mi QOS Mode Port base the output priority is determined by ingress port COS only the output priority is determined by COS only TOS only the output priority is determined by TOS only COS first the output priority is determined by COS and TOS but COS first TOS first the output priority is determined by COS and TOS but TOS first QOS policy Using the 8 4 2 1 weight fair queue scheme the output queues will follow 8 4 2 1 ratio to transmit packets from the highest to lowest queue For example 8 high queue packets 4 middle queue packets 2 low queue packets and the one lowest queue packets are transmitted in one turn Use the strict priority scheme always the packets in higher queue will be transmitted first until higher queue is empty Apply Click Apply to set the configurations ORing Industrial Networking Corp 53 IGS 3044GC User s Manual 5 1 5 2 Port base priority Port based Priority Port No Priority Port 0 i1 i 4 Port 02 d s a lt du LO Port 04 d s Port 05 d s HI 24 4 4 Port 06 d
50. g no security no security http Disable IP security of switch config no security http ee od no security telnet Disable IP security of switch config no security telnet 6 3 Commands Set List Port Commands Set interface fastEthernet Choose the port for switch config interface Portid duplex full half show security no security modification fastEthernet 2 Use the duplex switch config interface configuration fastEthernet 2 command to specify switch config if duplex full the duplex mode of operation for Fast Ethernet speed 10 100 1000 auto Use the speed switch config interface configuration fastEthernet 2 command to specify switch config if speed 100 the speed mode of operation for Fast Ethernet the speed can t be set to 1000 if the port isnt a giga port Use the flowcontrol switch config interface configuration fastEthernet 2 ORing Industrial Networking Corp 90 flowcontrol mode Symmetric Asymmetric IGS 3044GC User s Manual command on Ethernet switch config if flowcontrol mode ports to control traffic Asymmetric rates during congestion no flowcontrol Disable flow control of switch config if no flowcontrol interface Enable security of switch config interface fastEthernet 2 security enable switch config if security enable no security i i switch config interface fastEthernet 2 switch config if no security bandwidth type all Set interfa
51. h state N Use the state interface switch config interface Enable Disable configuration fastEthernet 2 command to specify switch config if state Disable the state mode of operation for Ethernet ports Use the disable form of this command to disable the port show interface show interface switch config interface configuration configuration status fastEthernet 2 switch config if show interface configuration show interface status show interface actual switch config interface status fastEthernet 2 switch config if show interface status show interface show interface switch conftig interface statistic counter fastEthernet 2 accounting switch config if show interface accounting no accounting Clear interface switch config interface accounting fastEthernet 2 information switch conftig if no accounting ORing Industrial Networking Corp 92 IGS 3044GC User s Manual 6 4 Commands Set List Trunk command set IGS 3044GCCommands Level Description aggregator priority Set E group system switch config aggregator priority 22 aggregator activityport Set activity port switch ien aggregator aggregator group Ne a trunk group switch config aggregator group 1 GroupID Port list with LACP active 1 4 lacp workp 2 GroupID 1to3 or Port list Member port switch config aggregator group 2 Workport list This parameter 1 4 3 lacp workp 3 could be a port range ex 1 4 or a port list
52. he configurations 802 1x Port Authorized Mode Show 802 1x port authorized state 802 1x Port Authorize State Port No Port Authorize State Port 01 Port 02 Port 03 Port 04 Port 05 Port 06 Port 07 Port 08 802 1x Port Authorize State interface ORing Industrial Networking Corp 67 IGS 3044GC User s Manual 5 1 8 5 IP Guard IP Guard Port Setting This page allows you to configure port configuration of IP Guard IP Guard is an intelligent and easy use function for IP security It could protect the network from unknown IP the IP not in allowed list attack The illegal IP traffic will be blocked Port No Port 01 Port 02 Port 03 Port 04 IP Guard Port Setting State interface The following table describes the labels in this screen Disable mode function is totally disabled Monitor mode function is disabled but keeps monitor the IP traffic Security mode function is enabled the illegal IP taffic will be blocked Click Apply to set the configurations Show help file IP Guard Allow List IP Guard is an intelligent and easy use function for IP security It could protect the network from unknown IP the IP not in allowed list attack The illegal IP traffic will be blocked This page allows you to configure IP Guard allowed list The IP traffic will be blocked if it was not in allowed list ORing Industrial Networking Corp 68 IGS 3044GC User s Manual IP Guard
53. idge ID SOOD001ES4011E A Root Priority Root Port Root Path Cost Max Age Hello Time Forward Delay RSTP Port Setting Path Cost Priority 1 200000000 0 240 Admin P2P Admin Edge Admin Non Stp priority must be a multiple of 16 ORing Industrial Networking Corp 35 IGS 3044GC User s Manual Fort Status Path Port Oper Oper Stp Part Cost Priority P2P Edge Neighbor state False Disabled Disabled Port 02 False Disabled Disabled ort 0 Disabled Disabled Port 04 Disabled Port 05 Disabled Path Cost 1 200000000 he cost of the path to the other bridge from this transmitting bridge at the specified port Enter a number 1 through 200000000 Port Priority 0 240 Decide which port should be blocked by priority in LAN Enter a number 0 through 240 The value of priority must be the multiple of 16 Admin P2P Some of the rapid state transactions that are possible within RSTP are dependent upon whether the port concerned can only be connected to exactly one other bridge i e It is served by a point to point LAN segment or it can be connected to two or more bridges i e It is served by a shared medium LAN segment This function allows the P2P status of the link to be manipulated administratively True means P2P enabling False means P2P disabling Admin Edge The port directly connected to end stations and it cannot create bridging loop in the network To configure the port as an edge port set the po
54. ing Corp 31 IGS 3044GC User s Manual 5 1 1 4 O Chain O Chain is the revolutionary network redundancy technology that provides the add on network redundancy topology for any backbone network providing ease of use while maximizing fault recovery swiftness flexibility compatibility and cost effectiveness in one set of network redundancy topologies O Chain allows multiple redundant network rings of different redundancy protocols to join and function together as a larger and more robust compound network topology i e the creation of multiple redundant networks beyond the limitations of current redundant ring technology O Chain Gl Enable Uplink Port Edge Port State Apply enable Enabing te O Ghainfuncton O Edge Port In the O Chain application the head and tail of two Switch Port must start the Edge MAC smaller Switch Edge port will be the backup and RM LED Light Edae Port Edae Port 0O Chain Edqe Port Edqe Port 0O Chain ORing Industrial Networking Corp 32 IGS 3044GC User s Manual 5 1 1 5 RSTP Repeater RSTP Repeater is a simple function this function can direct pass RSTP BPDU packet like two RSTP devices connected RS TP Repeater E Enable Uplink Port RSTP Edge Port ga een O enable Checks borto enable RSTP Repeater Edge Port Only the edge device connected to RSTP device needs to specify edge port The user must specify the edge port according
55. iod sec reauth period global j reauthperiod 3000 configuration command to set the reauth period 8021x _ portstate Use the 802 1x port switch config interface fastethernet disable reject accept state interface 3 authorize configuration switch config if 8021x portstate command to set the accept state of the selected port show 8021x Display a summary of switch gt show 8021x the 802 1x properties and also the port sates no 8021x Disable 802 1x switch config no 8021x function 6 13 Commands Set List TFTP command set Defaults IGS 3044GCCommands Level Description Example Save configuration to switch config backup TFTP and need to flash backup_cfg specify the IP of TFTP server and the file name of image restore flash restore_cfg Get configuration from switch config restore TFTP server and need flash restore_cfg to specify the IP of TFTP server and the file name of image ORing Industrial Networking Corp 103 IGS 3044GC User s Manual upgrade Upgrade firmware by switch contig upgrade flash upgrade_fw TFTP and need to lash upgrade_fw specify the IP of TFTP server and the file name of image 6 14 Commands Set List SYSLOG SMTP EVENT command set systemlog ip Set System log server switch config systemlog ip IP address IP address 192 168 1 100 systemlog mode Specified the log switch config systemlog mode client server both mode both show
56. ists the different location time zone for your reference AST Atlantic Standard 4 hours 8 am EDT Eastern Daylight ORing Industrial Networking Corp 2 IGS 3044GC User s Manual EST Eastern Standard 5 hours 7 am CDT Central Daylight CST Central Standard 6 hours 6 am MDT Mountain Daylight MST Mountain Standard 7 hours 5 am PDT Pacific Daylight PST Pacific Standard 8 hours 4am ADT Alaskan Daylight CET Central European FWT French Winter MET Middle European 1 hour 1 pm MEWT Middle European Winter SWT Swedish Winter EET Eastern European 2 hours 2pm USSR Zone 1 BT Baghdad USSR Zone 3 hours 3 pm WAST West Australian hours 7pm Standard CCT China Coast USSR 8 hours 8 pm Zone 7 JST Japan Standard 9 hours 9 pm USSR Zone 8 ORing Industrial Networking Corp 2 oS IGS 3044GC User s Manual Standard GST Guam Standard USSR Zone 9 IDLE International Date Line NZST New Zealand 12 hours Midnight Standard NZT New Zealand SNTP Sever IP Set the SNTP server IP address Address Daylight Saving Set up the Daylight Saving beginning time and Daylight Saving Period ending time Both will be different each year Daylight Saving Set up the offset time Offset Switch Timer Display the switch current time Apply Click Apply to activate the configurations PTP Client The Precision Time Protocol PTP is a time transfer
57. ity strings community community strings public Community no snmp snmpv3 user Remove specified switch config no snmp User Name user of SNMPv3 snmpv3 user test01 password password agent Privacy AuthPW PrivPW Authentication password could be Password Privacy empty Password no snmp server host Remove the SNMP switch config no snmp server Host address server host 192 168 10 50 6 11 Commands Set List Port Mirroring command set switch config monitor rx ORing Industrial Networking Corp 100 IGS 3044GC User s Manual 2 switch conftig if monitor RX Show port monitor switch config interface fastEthernet information 2 switch config if show monitor Disable source port of switch config interface fastEthernet monitor function 2 switch config if no monitor 6 12 Commands Set List 802 1x command set 8021x enable Use the 802 1x global switch config 8021x enable 8021x system radiousip IP address configuration command to enable 802 1x protocols Use the 802 1x switch config 8021x system system radious P radiousip 192 168 1 1 global configuration command to change the radious server IP port ID system server port serverport 1815 global configuration command to change the radious server port Use the 802 1x switch config 8021x system system account port jaccountport 1816 global configuration command to change the accounting port 8021x system serverpor
58. lled the Differentiated Services Code Point DSCP The output priority of a packet can be determined by this field and the priority value is supported Oto63 DSCP value map to 4 priority queues High Middle Low and Lowest Apply Click Apply to set the configurations Hep Showhelp le ORing Industrial Networking Corp a IGS 3044GC User s Manual 5 1 6 DHCP Server 5 1 6 1 DHCP Server Setting The system provides with DHCP server function Enable the DHCP server function the switch system will be a DHCP server DHCP Server Basic Setting DHCP Server Disable w Low IP Address 192 168 10 2 Hoh ID Address 192 160 10 200 Subnet Mask 255 255 255 0 Gateway 192 168 110 254 Lease Time sec DHCP Server Configuration interface The following table describes the labels in this screen DHCP Server Enable or Disable the DHCP Server function Enable the switch will Daa be the DHCP server on your local network Start IP Address The dynamic IP assign range Low IP address is the beginning of the dynamic IP assigns range For example dynamic IP assign range is from 192 168 1 100 to 192 168 1 200 192 168 1 100 will be the Start IP address End IP Address The dynamic IP assign range High IP address is the end of the dynamic IP assigns range For example dynamic IP assign range is from 192 168 1 100 to 192 168 1 200 192 168 1 200 will be the End IP address Subnet Mask The dynamic IP assign
59. llowing table describes the labels in this screen Port Port number of entry ee Add to Allow List If you want to allow the IP traffic please check this box and apply it ORing Industrial Networking Corp 70 IGS 3044GC User s Manual 5 1 9 Warning Warning function is very important for managing switch You can manage switch by SYSLOG E MAIL and Fault Relay It helps you to monitor the switch status on remote site When events occurred the warning message will send to your appointed server E MAIL or relay fault to switch panel System alarm support two warning mode 1 SYSLOG 2 E MAIL You can monitor switch through selected system events Warning Fault Relay Alarm When any selected fault event is happened the Fault LED in switch panel will light up and the electric relay will signal at the same time Fault Relay Alarm Power Failure LIPWR 1 LIPWR 2 Port Link Down Broken Port o1 Port 02 Port 03 C Port 04 C Port 05 Port 06 Port o7 CL Port og ve System Warning SYSLOG Setting The SYSLOG is a protocol to transmit event notification messages across networks Please refer to RFC 3164 The BSD SYSLOG Protocol SYSLOG Setting Syslog Mode Syslog Server IP Address 192 168 10 66 Apply System Warning SYSLOG Setting interface ORing Industrial Networking Corp 71 IGS 3044GC User s Manual The following table describes the labels in this screen SYSLOG Mode WR
60. manager by entering the IP address of the station and a community string To define management stations as trap manager and enter SNMP community strings and selects the SNMP version SNMP Trap Setting Trap Server Setting Server IP Trap Version Trap Server Profile Server IP Community Trap Version nome SNMP Trap Setting interface The following table describes the labels in this screen The server IP address to receive Trap Community for authentication ads Lusensne OO mep nien ORing Industrial Networking Corp 60 5 1 7 3 SNMPV3 NMP SNMP v3 Setting IGS 3044GC User s Manual SNMPv3 Engine ID f465000003001e940a002b Context Table User Table New User Profile Current User Profiles nome User ID Authentication Password Privacy Password Group Table Current Group content New Group Table Ome i none Security Name User ID Group Name Current Access Tables New Access Table fe es Context rte RS Group Name Security Level Context Match Rule Write View Name NoAuthNoPriv AuthNoPriv AuthPriv Exact Prefix Notify View Name MIBView Table Current MIBTables none View Name SubOid Tree Type Note New MIBView Table ze Excluded Included Any modification of SNMPv3 tables might cause MIB accessing rejection Please take notice of the causality between the tables before you modify these tables
61. name Click Remove to remove unwanted context name Show help file Corp 62 IGS 3044GC User s Manual 5 1 8 Security Five useful functions can enhance security of switch IP Security Port Security MAC Blacklist and MAC address Aging and 802 1 x protocol 5 1 8 1 Management Security Only IP in the Secure IP List can manage the switch through your defined management mode WEB Telnet SNMP Mode Enable v Enable WEB Management Enable Telnet Management Enable SNMP Management Secure IP List Secure IP1 WS Secure IP WS IP Security interface The following table describes the labels in this screen IP security MODE Enable Disable the IP security function Enable WEB Mark the blank to enable WEB Management Management Enable Telnet Mark the blank to enable Telnet Management Management Enable SNMP Mark the blank to enable MPSN Management Management Apply Click Apply to set the configurations Show help file 5 1 8 2 Static MAC Forwarding Static MAC Forwarding is to add static MAC addresses to hardware forwarding database If port security is enabled at Port Control page only the frames with MAC addresses in this list will be forwarded otherwise will be discarded ORing Industrial Networking Corp 63 IGS 3044GC User s Manual MAC Address _ Port No MAC Address Port No oO 001122354455 Port 06 Port Security interface The following table describes th
62. network administrators to manage network performance find and solve network problems and plan for network growth Network management systems learn of problems by receiving traps or change notices from network devices implementing SNMP 5 1 7 1 SNMP Agent Setting You can set SNMP agent related information by Agent Setting Function SNMP Agent Setting SNMP Agent Version Apply SNMP V1 V2c Community Community String SNMP Agent setting interface The following table describes the labels in this screen SNMP agent Version SNMP V1 V2c Community Three SNMP versions are supported such as SNMP V1 SNMP V2c and SNMP V3 SNMP V1 SNMP V2c agent use a community string match for authentication that means SNMP servers access objects with read only or read write permissions with the community default string public private SNMP V3 requires an authentication level of MD5 or DES to encrypt data to enhance data security SNMP Community should be set for SNMP V1 V2c Four sets of Community String Privilege are supported Each Community String is maximum 32 characters Keep empty to remove this ORing Industrial Networking Corp 59 IGS 3044GC User s Manual Apply Click Apply to activate the configurations 5 1 7 2 SNMP Trap Setting A trap manager is a management station that receives traps the system alerts generated by the switch If no trap manager is defined no traps will issue Create a trap
63. ns Cable Types and Specifications Cable Max Length Connector 10BASE T Cat 3 4 5 100 ohm UTP 100 m 828 ft RJ 45 100BASE TX Cat 5 100 ohm UTP UTP 100 m 828 ft RJ 45 1000BASE TX Cat 5 Cat 5e 100 ohm UTP UTP 100 m 828ft RJ 45 4 1 1 100BASE TX 10BASE T Pin Assignments With 100BASE TX 10BASE T cable pins 1 and 2 are used for transmitting data and pins 3 and 6 are used for receiving data RJ 45 Pin Assignments RD The IGS 3044GC switches support auto MDI MDI X operation You can use a straight through cable to connect PC to switch The following table below shows the 10BASE T 100BASE TX MDI and MDI X port pin outs ORing Industrial Networking Corp 13 IGS 3044GC User s Manual MDI MDI X pins assignment wen wen Note and signs represent the polarity of the wires that make up each PinNumber Not used o 6 a SE wire pair 1000 Base T MDI MDI X pins assignment ween was Note and signs represent the polarity of the wires that make up each wire pair PinNumber O C EE H ORing Industrial Networking Corp 14 4 2 SFP The IGS 3044GC has fiber optical ports with SFP connectors IGS 3044GC User s Manual The fiber optical ports are in multi mode 0 to 550M 850 nm with 50 125 um 62 5 125 um fiber and single mode with LC connector of Switch B Switch A wa o 4 3 Console Cable IGS 3044GC switches can be management by co
64. nsole port be found in the package i At Sr La T z IF l Fri i i d ef i V ie Ay i Please remember that the TX port of Switch A should be connected to the RX port Switch B Fiber cord The DB 9 to RJ 45 cable can You can connect them to PC via a RS 232 cable with DB 9 female connector and the other end RJ 45 connector connects to console port of switch PC pin out male assignment RS 232 with DB9 female connector DB9 to RJ 45 Pin 2 RD Pin 3 TD Pin 5 GD DEBY Male Shield Signal Ground H Tg gar Ring Indicator DTE Ready a 4 g Clear to Send Transmitted Data 2 d e Received Line Sgna Detect DCE Ready t j Received by DTE Device oR Traeemfttel from DTE Device ORing Industrial Networking Corp DBY Female Received Une Signal Detect bh A 1 r Be LN E Ready Transmitted Data eg 7 ee Clear to Send Received Data 5 E 5 Signal Ground 7 Ring Indicator ij Received by DCE Device OB Transmitted from DCE Device 15 IGS 3044GC User s Manual WEB Management While making any establishment and upgrading firmware please remove physical loop connection first DO NOT power off equipment during firmware is upgrading 5 1 Configuration by Web Browser This section introduces the configuration by Web browser 5 1 1 About Web based Management An embedded HTML web site resides in flash memory on the CPU board It contains advanced managemen
65. o those end destinations that require that traffic and reduces the amount of traffic on the Ethernet LAN IGMP Snooping IGMP Snooping Enable v2 IGMP Query Mode Disable SMP Snooping Table IP Address VLAN ID Member Port 230 0 0 20 Port 07 IGMP Snooping interface The following table describes the labels in this screen IGMP Snooping Table Show current IP multicast list IGMP Protocol Enable Disable IGMP snooping IGMP Query Switch will be IGMP querier or not There should exist one and only one IGMP querier in an IGMP application The Auto mode means that the querier is the one with lower IP address Apply Click Apply to set the configurations ORing Industrial Networking Corp 42 IGS 3044GC User s Manual 5 1 2 2 MVR MVR Function can provide a different VLAN users to receive MVR Mode VLAN Multicast Packet MVR MVR Mode MVR VLAN Port Type Immediate Leave por o7 Es O Label Description MVR Mode Enable or Disable MVR Mode MVR VLAN ong MVR VLAN TYPE eet Port Type to inactive gt Receiver Source Immediate Leave Enable or disable Immediate leave ORing Industrial Networking Corp 43 IGS 3044GC User s Manual 5 1 2 3 Static Multicast Filtering Static Multicast filtering is the system by which end stations only receive multicast traffic if they register to join specific multicast groups With multicast filtering network devices only forward multicast tra
66. on for connecting two Rings Coupling Port Link to Coupling Port of the switch in another ring Coupling Ring need four switch to build an active and a backup link Set a port as coupling port The coupled four ports of four switches will be run at active backup mode Control Port Link to Control Port of the switch in the same ring Control Port used to transmit control signals Enable Dual Homing Mark to enable Dual Homing By selecting Dual Homing mode O Ring will be connected to normal switches through two RSTP links ex backbone Switch The two links work as active backup mode and connect each O Ring to the normal switches in RSTP mode Apply Click Apply to set the configurations Note We don t suggest you to set one switch as a Ring Master and a Coupling Ring at the same time due to heavy load 5 1 1 3 OPEN Ring Open Ring technology can be applied for other vendor s proprietary ring Thus you can add switches of ORing into the network constructed by other ring technology and enable Open Ring to co operate with other vendor s managed switch ORing Industrial Networking Corp 30 IGS 3044GC User s Manual Open Ring Vender Morn 1st Ring Port Dol w 2nd RingPort Pot w Apply Open Ring interface Enawie Enabing tne Open Ringiuncion The application of Open Ring is shown as below ORing Switch ORing Switch ORing Switch Open Ring connection ORing Industrial Network
67. ons ORing Switch Model IGS 3044GC Physical Ports 10 100 1000 Base T X Ports in RJ 45 Auto MDI MDIX Gigabit Combo Port with 10 100 1000Base T X and 100 1000Base X SFP Port Technology IEEE 802 3 for 10Base T IEEE 802 3u for 100Base TX and 100Base FX IEEE 802 3z for 1000Base X IEEE 802 3ab for 1000Base T IEEE 802 3x for Flow control IEEE 802 3ad for LACP Link Aggregation Control Protocol IEEE 802 1D for STP Spanning Tree Protocol Ethernet Standards IEEE 802 1p for COS Class of Service IEEE 802 1Q for VLAN Tagging IEEE 802 1w for RSTP Rapid Spanning Tree Protocol IEEE 802 1s for MSTP Multiple Spanning Tree Protocol IEEE 802 1x for Authentication IEEE 802 1AB for LLDP Link Layer Discovery Protocol MAC Table 8192 MAC addresses Switching latency 7 us Switching bandwidth 16Gbps Switch Properties Max Number of Available VLANs 4096 IGMP multicast groups 1024 Port rate limiting User Define Enable disable ports MAC based port security Port based network access control 802 1x VLAN 802 1Q to segregate and secure network traffic Security Features Supports Q in Q VLAN for performance amp security to expand the VLAN space Radius centralized password management SNMP V1 V2c V3 encrypted authentication and access security STP RSTP MSTP IEEE 802 1D w s Redundant Ring O Ring with recovery time less than 20ms over 250 units TOS Diffserv supported Quality of Service 802 1p for real
68. protocol defined in the IEEE 1588 2002 standard that allows precise synchronization of networks e g Ethernet Accuracy within the nanosecond range can be achieved with this protocol when using hardware generated timestamps PTP Client Disable sl PTP Client Enable Disable PTP Client ORing Industrial Networking Corp 24 IGS 3044GC User s Manual 5 1 4 5 LLDP LLDP Link Layer Discovery Protocol function allows the switch to advertise its information to other nodes on the network and store the information it discovers LLDP TESTEN Enable LLDP Interval Apply Neighbor Info Table Port System Name MAC Address IP Address ime 1GS 3044GC 00 1E 94 34 04 B80 19 168 10 20 LLDP configuration interface The following table describes the labels in this screen Enable or Disable LLDP function Click Apply to set the configurations Hep Srowhelp fe 5 1 4 6 Modbus TCP Support Modbus TCP About Modbus please reference http www modbus org Modbus TCP Mode The following table describes the labels in this screen Mode Enable or Disalble Modbus TCP function ORing Industrial Networking Corp 25 IGS 3044GC User s Manual 5 1 4 7 Auto Provision Auto Provision allows you to update the switch firmware automatically You can put firmware or configuration file on TFTP server When you reboot the switch it will upgrade automatically Befor
69. rt to True Admin Non STP The port includes the STP mathematic calculation True is not including STP mathematic calculation False is including the STP mathematic calculation Apply Click Apply to set the configurations ORing Industrial Networking Corp 36 IGS 3044GC User s Manual 5 1 1 8 MSTP Multiple Spanning Tree Protocol MSTP is a standard protocol base on IEEE 802 1s The function is that several VLANs can be mapping to a reduced number of spanning tree instances because most networks do not need more than a few logical topologies It supports load balancing scheme and the CPU is sparer than PVST Cisco proprietary technology IGS 3044GP RES 3242GC E VLAN 100 VLAN 200 ORing Industrial Networking Corp 37 IGS 3044GC User s Manual MSTP Bridge Setting MSTP Enable Force Version Configuration Name Revision Level 0 65535 Priority 0 61440 Max Age Time 6 40 Hello Time 1 10 Forward Delay Time 4 30 j S AEA E S dE z Max Hops 1 40 Priority must a multiple of 4096 2 Forward Delay Time 1 should be greater than or equal to the Max Age The Max Age should be greater than or equal to 2 Hello Time 1 Apply MSTP Setting interface The following table describes the labels in this screen MSTP Enable You must enable or disable MSTP function before configuring the wesen related parameters Force Version The Force Version parameter can be used to force
70. s of the product s associated with this publication DISCLAIMER Information in this publication is intended to be accurate ORing shall not be responsible for its use or infringements on third parties as a result of its use There may occasionally be unintentional errors on this publication ORing reserves the right to revise the contents of this publication without notice CONTACT INFORMATION ORing Industrial Networking Corp 4F NO 3 Lane235 Baociao Rd Sindian City Taipei County 23145 Taiwan R O C Tel 886 2 2918 3036 Fax 886 2 2918 3084 Website www oring networking com Technical Support E mail support oring networking com Sales Contact E mail sales oring networking com Headquarters sales oring networking com cn China ORing Industrial Networking Corp 1 IGS 3044GC User s Manual Table of Content Getting to Know Your SWIG EE 5 1 1 About the IGS 3044GC Managed Industrial Gwtch ce ceeeeecceccsceeeeeeeeeeeeeeeeeens 5 1 2 DOMWANC EE 5 1 3 Hardware EE EE 6 PlarOware Irrel 7 2 1 HASTA AG SWVC ON BEE 7 2 1 1 Mount IGS 3044GCSERIES on DIN Rail 7 2 2 Wall Mounting Installation i E E E E ETET 8 Hardware e WEE 9 3 1 FONU Se latte cictoune cases aatees sigs axe sycasnae ci ceane sa aoneesice oe anne Naas aotea uaa sa cement 9 3 2 FONE EE EE 11 3 3 TOD VIEW EE 12 le 13 4 1 Sne Ee 13 4 1 1 100BASE TX 10BASE T Pin Assignments 0annnnaannnneannnnennnnnnnirennnrnenrnnnenn 13 4 2 E E e
71. t H Disa Auto Detect 100 1000 SFP Enable w Port Control interface The following table describes the labels in this screen Port NO O Port number for setting State Enable Disable the port Speed Duplex You can set Auto negotiation 100 full 100 half 10 full 10 half mode Flow Control Support symmetric and asymmetric mode to avoid packet loss when congestion occurred Security Enabled port security will disable MAC address learning in this port Thus only the frames with MAC addresses in port security list will be forwarded otherwise will be discarded Auto Detect 100 1000 Auto Detect SFP port SFP Module speed 100M 1000M Apply Click Apply to activate the configurations ORing Industrial Networking Corp 45 IGS 3044GC User s Manual 5 1 3 2 Port Status The following information provides the current port status information Port Status Port No Link State Speed Duplex Flow Control Port 01 Enal z Port 02 Port 03 Down Port 04 aman cae Enable Port Status interface See rrr r 5 1 3 3 Port Alias The user can define the name of every Ports Can let user convenient management every Port Port Alias Port Alias 5 ee 5 1 3 4 Rate Limit By this function you can limit traffic of all ports including broadcast multicast and flooded unicast You can also set Ingress or Egress to limit traffic received or transmitted ban
72. t save Configuration System Configuration interface ORing Industrial Networking Corp 81 IGS 3044GC User s Manual The following table describes the labels in this screen Save all configurations 5 1 12 Factory Default Factory Default Keep current IP address setting Keep current username amp password Factory Default interface Reset switch to default configuration Click Reset to reset all configurations to the default value You can select Keep current IP address setting and Keep current username amp password to keep current IP and username and password 5 1 13 System Reboot System Reboot Boot from image bank 0 k3 04 v1 00 built at May 21 2012 13 54 14 image bank 1 empty Reboot How System Reboot interface ORing Industrial Networking Corp 82 IGS 3044GC User s Manual Command Line Interface Management 6 1 About CLI Management Besides WEB base management I GS 3044GCalso supports CLI management You can use console or telnet to management switch by CLI CLI Management by RS 232 Serial Console 9600 8 none 1 none Before Configuring by RS 232 serial console use an RJ45 to DB9 F cable to connect the Switches RS 232 Console port to your PCs COM port Follow the steps below to access the console via RS 232 serial cable Step 1 From the Windows desktop click on Start gt Programs gt Accessories gt Communications gt Hyper Terminal B Accessibility
73. t Communications J HyperTerminal Network Time Fratacol ET Network and Dial up Connections System Tools Le HyperTerminal ee Acrobat Reader 5 0 W Address Book E3 Calculator E Command Prompt CN Net Tune A7 Motepad ee Update ki Paint us 3 Windows Explorer ie Accessories Le Network Associates Documents dE Startup S Gi d E Internet Explorer ES Outlook Express Search d i H Programs 7 Settings E Help Ruri B Shut Down ORing Industrial Networking Corp 83 IGS 3044GC User s Manual Step 2 Input a name for new connection Connection Description Enter a name and choose an icon for the connection Name Disconnected Auto detect Auto detect SCROLL CAFS NUM Capture Print echo Step 3 Select to use COM port number termnial HyperTerminal SH SS d Ioj x File Edit View Call Transfer Help SECH termnial Enter details for the phone number that you want to dial Country regiors Taiwan 886 Area code El Phone number ee Connect using S Cancel Disconnected Auto detect Auto detect SCROLL caps NUM Capture Print echo E ORing Industrial Networking Corp 84 IGS 3044GC User s Manual Step 4 The COM port properties setting 9600 for Bits per second 8 for Data bits None for Parity 1 for Stop bits and none for Flow control ETE a kermonial Hynne COM Properties Fort Settings Bits per second a600 sl Data bits E sl Parit
74. t features and allows you to manage the switch from anywhere on the network through a standard web browser such as Microsoft Internet Explorer The Web Based Management function supports Internet Explorer 5 0 or later It is based on Java Applets with an aim to reduce network bandwidth consumption enhance access speed and present an easy viewing screen Note By default IE5 0 or later version does not allow Java Applets to open sockets You need to explicitly modify the browser setting in order to enable Java Applets to use network ports Preparing for Web Management The default value is as below IP Address 192 168 10 1 Subnet Mask 255 255 255 0 Default Gateway 192 168 10 254 User Name admin Password admin System Login 1 Launch the Internet Explorer 2 Type http and the IP address of the switch Press Enter ORing Industrial Networking Corp 16 IGS 3044GC User s Manual File Edit Yiew Favorites Tools Help ae pack x ai L ES Search S y Favorites amp A A fr ptn 192 168 10 1 a EJ so Links The login screen appears WW Address 3 d Key in the username and password The default username and password is admin 5 Click Enter or OKT button then the main interface of the Web based management appears Connect to 192 168 10 1 index htm User name admin D Password Ce Remember my password Login screen Main Interfa
75. t i Use the 802 1x switch config 8021x system ORing Industrial Networking Corp 101 8021x system sharekey Use the 802 1x ID system share key global configuration command to change 8021x system nasid Use the 802 1x words system nasid global configuration command to change the NAS ID 8021x misc quietperiod Use the 802 1x misc sec quiet period global configuration command to specify i the switch 8021x misc txperiod Use the 802 1x misc TX period global configuration command to set the TX period sec 8021x misc Use the 802 1x misc supportimeout sec supp timeout global configuration command to set the supplicant timeout 8021x misc servertimeout sec Use the 802 1x misc server timeout global configuration command to set the server timeout Use the 802 1x misc 8021x misc maxrequest number max request global configuration command to set the MAX requests ORing Industrial Networking Corp the shared key value the quiet period value IGS 3044GC User s Manual switch config 8021x system sharekey 123456 switch contig 8021x system nasid test1 switch contig 8021x misc quietperiod 10 switch contig 8021x misc txperiod 5 switch config 8021x misc supportimeout 20 switch config 8021x misc servertimeout 20 switch config 8021x misc maxrequest 3 102 IGS 3044GC User s Manual Use the 802 1x misc _ switch config 8021x misc reauthper
76. the Max Age The Max Age should be greater than or equal to 2 Hello Time 1 RSTP Setting interface The following table describes the labels in this screen Label Description RSTP mode You must enable or disable RSTP function before configuring the related parameters Priority 0 61440 A value used to identify the root bridge The bridge with the lowest value has the highest priority and is selected as the root If the value changes You must reboot the switch The value must be multiple of 4096 according to the protocol ORing Industrial Networking Corp 34 IGS 3044GC User s Manual Max Age Time 6 40 The number of seconds a bridge waits without receiving Spanning tree Protocol configuration messages before attempting a reconfiguration Enter a value between 6 through 40 Hello Time 1 10 The time that controls switch sends out the BPDU packet to check RSTP current status Enter a value between 1 through 10 Forwarding Delay Time The number of seconds a port waits before changing from its 4 30 Rapid Spanning Tree Protocol learning and listening states to the forwarding state Enter a value between 4 through 30 Apply Click Apply to set the configurations NOTE Follow the rule to configure the MAX Age Hello Time and Forward Delay Time 2 x Forward Delay Time value 1 gt Max Age value gt 2 x Hello Time value 1 Show RSTP algorithm result at this table Root Bridge Information Br
77. tion of QoS configuration noe Disable QoS function switch config no qos 6 8 Commands Set List IGMP command set Example o igmp enable Enable IGMP switch config igmp enable Is Igmp query auto Set IGMP query to switch contig lgmp query auto we Set IGMP query to switch config lgmp query force force mode Displays the details of switch show igmp multi an IGMP snooping entries Disable IGMP switch config no igmp snooping function no igmp query show igmp Displays the details of switch show igmp configuration configuration an IGMP configuration Disable IGMP query switch no igmp query ORing Industrial Networking Corp 98 IGS 3044GC User s Manual 6 9 Commands Set List MAC Filter Table command set mac address table static Configure MAC switch config interface fastEthernet hwaddr address table of 2 MAC interface static switch config if mac address table static hwaddr 000012345678 mac address table filter Configure MAC switch contig mac address table hwaddr address table filter filter hwaddr 000012348678 MAC show mac address table Show all MAC switch show mac address table geg A en show mac address table Show static MAC switch show mac address table Le e show mac address table Show filter MAC switch show mac address table filter filter address table no mac address table Remove an entry of switch config interface fastEthernet static hwaddr MAC address table of 2 MA
78. tree enable spanning tree priority Configure spanning _ switch config spanning tree priority 0to61440 tree priority parameter 32767 spanning tree max age Use the spanning tree switch config spanning tree seconds max age global max age 15 configuration command to change the interval between messages the spanning tree receives from the root switch If a switch does not receive a bridge protocol data unit BPDU message from the root switch within this interval it recomputed the Spanning Tree Protocol STP topology ohna Industrial Netwering Com e Industrial Networking Corp 95 IGS 3044GC User s Manual spanning tree Use the spanning tree switch config spanning tree hello time seconds hello time global hello time 3 configuration command to specify the interval between hello bridge protocol data units BPDUs spanning tree Use the spanning tree switch config spanning tree forward time seconds forward time global forward time 20 configuration command to set the forwarding time for the specified spanning tree instances The forwarding time determines how long each of the listening and learning states last before the port begins forwarding stp path cost Use the spanning tree switch config interface fastEthernet 1to200000000 cost interface 2 configuration switch config if stp path cost 20 command to set the path cost for Spanning Tree Protocol S
79. trunk link tag 2 3 6 99 trunk link tag port belong to a trunk or Tagged VID List group this command _ switch vian vlan 8021q port 3 can t be applied trunk link tag 3 20 vlan 8021q port V Assign a hybrid link for switch vlan vlan 80219 port 3 PortNumber VLAN by port if the hybrid link untag 4 tag 3 6 8 hybrid link untag port belong to a trunk jor UntaggedVID group this command switch vian vlan 8021q port 3 tag cant be applied hybrid link untag 5 tag 6 8 Tagged VID List vlan 8021q aggreator V Assign a access link switch vlan vlan 8021q aggreator 3 TrunkID for VLAN by trunk access link untag 33 access link untag group UntaggedVID vlan 8021q aggreator V Assign a trunk link for switch vlan vlan 8021q aggreator 3 TrunkID VLAN by trunk group trunk link tag 2 3 6 99 trunk link tag or TaggedVID List switch vlan vlan 8021q aggreator 3 ORing Industrial Networking Corp 94 IGS 3044GC User s Manual vlan 8021q aggreator V Assign a hybrid link for switch vlan vlan 8021q aggreator 3 PortNumber VLAN by trunk group hybrid link untag 4 tag 3 6 8 hybrid link untag or Untagged VID switch vian vlan 8021q aggreator 3 tag hybrid link untag 5 tag 6 8 TaggedVID List V Show VLAN switch vlan show vlan 23 information 6 6 Commands Set List Spanning Tree command set IGS 3044GCCommands Level Description Description Example spanning tree enable Feier gemeng spanning tree switch config spanning
80. witches status 1 2 Software Features m World s fastest Redundant Ethernet Ring O Ring Recovery time lt 10ms over 250 units connection Supports Ring Coupling Dual Homing over O Ring Supports SNMPv1 v2 v3 amp RMON amp Port base 802 1Q VLAN Network Management Event notification by Email SNMP trap and Relay Output Web based Telnet Console CLI configuration Enable disable ports MAC based port security Port based network access control 802 1x VLAN 802 1Q to segregate and secure network traffic Radius centralized password management SNMPv3 encrypted authentication and access security RSTP 802 1w Quality of Service 802 1p for real time traffic VLAN 802 1Q with double tagging and GVRP supported IGMP Snooping for multicast filtering Port configuration status statistics mirroring security Remote Monitoring RMON ORing Industrial Networking Corp 5 1 3 Hardware Features Redundant three DC power inputs Operating Temperature 40 to 70 C for IGS 3044GP 10 to 60 C for IGS 3044GC Storage Temperature 40 to 85 C Operating Humidity 5 to 95 non condensing Casing IP 30 4 x 10 100 1000Base T X Gigabit Ethernet port 4x 1000Base X SFP amp 1000Base T X COMBO for IGS 3044GC Console Port Dimensions W x D x H 74 3 mm W x 109 2 mm D x 153 6 mm H ORing Industrial Networking Corp Hardware Installation 2 1 Installing Switch on DIN Rail Each switch has a DIN Rail kit on rear pan
81. y None sl Stop bits fi sl Flow control None sl Restore Defaults OF Cancel Apply Disconnected Auto detect Auto detect SCROLL cars NUM Capture Print echo db Step 5 The Console login screen will appear Use the keyboard to enter the Username and Password The same with the password for Web Browser then press Enter IG 30446C Command Line Interface Username _ Password CLI Management by Telnet Users can use TELNET to configure the switches The default value is as below ORing Industrial Networking Corp 85 IGS 3044GC User s Manual IP Address 192 168 10 1 Subnet Mask 255 255 255 0 Default Gateway 192 168 10 254 User Name admin Password admin Follow the steps below to access the console via Telnet Step 1 Telnet to the IP address of the switch from the Windows Run command or from the MS DOS prompt as below Si Type the name of a program Folder document or Internet resource and Windows will open it For you Open telnet 192 168 10 1 Cancel Browse Step 2 The Login screen will appear Use the keyboard to enter the Username and Password The same with the password for Web Browser and then press Enter IG 304460 Command Line Interface Username _ Password Commands Level User EXEC Begin a session switch gt Enter logout The user command with your switch or quit available at the level of user is the subset
82. y Click Apply to set the configurations Port Trunk Status Port Trunk Status GroupID Trunk Member Type Trunk 1 MA Trunk 2 RE Static Trunk 3 Trunk 4 Port Trunk Status interface Group Key Trunk Group number Port Member Show Group port info ORing Industrial Networking Corp 48 IGS 3044GC User s Manual 5 1 3 6 Loop Guard This feature prevents the loop attack When the port receives loop packet This port will auto disable prevent the loop attack affect other network devices Loop Guard Port No Active Port State Port 06 Enable Port 03 Enable Label Loop Guard Enable or Disable 5 1 4 VLAN A Virtual LAN VLAN is a logical network grouping that limits the broadcast domain which allows you to isolate network traffic Only the members of the VLAN will receive traffic from the same members of VLAN Basically creating a VLAN from a switch is logically equivalent of reconnecting a group of network devices to another Layer 2 switch However all the network devices are still plugged into the same switch physically The switch supports port based and 802 1Q tagged based VLAN The default configuration of VLAN operation mode is at 802 1Q 5 1 4 1 VLAN Setting IEEE 802 1Q Tagged based VLAN is an IEEE 802 1Q specification standard and t is possible to create a VLAN across devices from different switch venders IEEE 802 1Q VLAN uses a technique to insert a tag into the Ethern

Download Pdf Manuals

Related Search

Related Contents

Samsung AQV09KBAN Instrukcja obsługi  シンク前スクリーン/コンロ前用ガラス 取扱説明書  Canon PIXMA iP2820 Getting Started Guide  Télécharger la fiche technique  Manual de instrucciones  SMC EZ-Stream Universal Wireless Router (smc2304wbr-ag)    JVC CA-NXF3 User's Manual  Télécharger le fichier complet - 10.41 Mo  Verificação Biométrica da Palma da Mão com Identificação via  

Copyright © All rights reserved. Failed to retrieve file