Talent LP64LED-FLAT User Manual
Contents
1. COMMON ak DMX VAN DMX INPUT o3 3 DMX OUTPUT A DMX ae Termination reduces signal errors and to avoid signal i ie transmission problems and interference Itis always advisable to connect a DMX terminal Vs E Resistance 120 ohm 1 4W between pin2 DMX and V pin3 DMAX of the last fixture e If you are using a controller with 5 pin DMX output use a 5 pin to 3 pin adapter cable e Connect fixtures together in a daisy chain by connecting the DMX output of the first fixture to the DMX input of the next fixture This cable cannot be branched or split by a Y cable Inadequate or damaged cables bad solder joints or corroded connectors can easily distort the signal cause errors and shut down the system Never allow contact between the data common shield connection XLR Pin 1 and the fixture s chassis electrical ground The DMX output and input connectors are pass through to maintain the DMX circuit if power to one of the units is disconnected e On the last fixture the DMX output should be terminated with a terminator to reduce signal errors Solder a 120 ohm 1 4 watt resistor between pin 2 DMX and pin 3 DMX on a 3 pin XLR plug and connect it to the DMX output of the last fixture 6 How to Set the Unit 6 1 Control Panel Dispiay Normal a CF p Down O O Enter To go forward in the selected function or go back the last layer menu To go forward in the selected function or increase parameter2. For additional details about DMX operation please review Section 10 8 2 IR Remote Control Functions 1 Auto Auto show 2 Sound Sound active 3 DMX DMxX512 control switch mode between address and channel 4 Black Out Acts as a shutoff button when activated pressing this butt 5 Red Red LEDs on 6 Green Green LEDs on T Blue Blue LEDs on 8 White Red Green and Blue LEDs are tumed on 9 Increase parameters In Color mode the light shows in the same color as the button s color 10 Reduce parameters In Color mode the light shows in the same color as the button s color 11 0 9 In DMX mode the 0 through 9 buttons set DMX addresses on the fixture When DMX is first selected the 0 9 buttons change the address Pressing the DMX button again allows you to change the channel 12 Jump Jump color change mode 13 Fade Gradual change mode 14 Color static color lf the program is not in Color mode and you want to select color you must first press the Color button 15 Flash Only in Auto Fade Jump and COLOR modes Press once for strobe mode press again to retum to the previus program Remark Please make sure there is nothing between the remote controller and the fixture Maximum distance for the remote to work is 10 meters 9 Troubleshooting Here are some troubleshooting suggestions A The fixture does not work there is no light output 1 Check the connection of power and main fuse 2
3. Measure the voltage output on your power receptacle to ensure proper voltage B Fixture does not respond to DMX control 1 DMX LED should be on If not check DMX connectors and cables for proper connection 2 If DMX LED 1s on but not responding to a channel check the DMX address settings and DMX polarity 3 If you have intermittent DMX signal problems check the pins on the cable connectors and on the fixture 4 Try to use a different DMX controller 5 Interference may occur if DMX cables are run alongside high voltage cables C Fixture responds erratically to DMX control 1 You may have a break in the DMX cabling Check the LED for the response of the master slave mode signal 2 Wrong DMX address in the fixture Set the fixture to the proper address 3 Use of microphone cables for DMX connections can cause errors D The fixture doesn t respond to sound 1 Make sure the fixture is not set to receive a DMX signal 2 Check the fixture s internal microphone by tapping the microphone 10 DMX General Information The DMX512 digital communication protocol was introduced to control stage lighting and special effects The DMX standard features 512 available channels and they are assignable in any sequence that conforms to the user s needs Each DMX capable fixture requires one or more sequential channels A starting address which indicates the first control channel reserved for that particular fixture must
4. use as there might be a hazard of electrical shock e To prevent or reduce the risk of electrical shock or fire do not expose the fixture to rain or moisture e The fixture must be replaced 1f there is visible damage to the housing e Do not look directly at the LED light beam while the fixture is on Warning Please read the instructions carefully They include important information about installation operation and maintenance Do not connect more than 32 units in series daisy chaining on a single power circuit Caution There are no user serviceable parts inside the fixture Do not open the housing or attempt any repairs yourself In the unlikely situation your unit may require service please contact your dealer or Talent Sound amp Lighting 2 Technical Specifications 1 tee fl im 6 216 CH ON CX WN Q ORC SSOOG ALS OOOOOOOC e DMX channels 3 5 7 selectable via digital display 181 Ultra Bright 10 mm LEDs Red 49 Green 72 Blue 60 e 125 Static Colors Dimmer Strobe Fade Jump e Auto sound active DMX and master slave modes e Internal programs with sound activation e 3 pin XLR in out sockets for DMX control e RGB color mixing e Beam angle 20 e Power consumption 20 watts Power input AC 90V 250V 50 60 Hz e Dimension 10 83 diameter x 4 13 deep e Weight 3 52 Ibs 3 Installation The unit should be mounted via its screw holes on its bracket Always ensure that the unit 1s
5. be assigned to the fixture before the controller can recognize it DMX controllable fixtures may vary in the number of channels they require depending on the fixtures features and or functionality Channels should never be permitted to overlap otherwise for example a fader that controls blue output on one fixture may cause strobing or dimming on an adjacent incorrectly assigned fixture Multiple fixtures of the same type that use an identical starting address will function in unison Fixtures assigned properly spaced starting addresses will operate individually but a DMX controller with sufficient channels can be configured to run these same fixtures either combined or independently The sequence in which DMX fixtures are connected has no effect on how a controller communicates with each individual lighting fixture Although 3 pin XLR mic cables may be used to connect DMX fixtures over short runs longer distances will introduce data errors due to the mic cable s incorrect impedance For best results Talent Sound amp Lighting recommends the use of correct 120 ohm low capacitance twisted pair cable designed for the DMX512 protocol It is also suggested that a termination resistor plug be used on the output connector of the last fixture in an array of DMX instruments This resistance ensures proper data transmission Notes
6. eeds to have an address set when in DMX mode to receive the data sent by the controller The address number is between 0 511 usually 0 amp 1 are equal to 1 Please refer to the following diagram to set the address for the first four units LT LL SILL SLL 3 The numbers 1 5 9 and 13 indicate the starting address of each of the fixtures B Master Slave operation The fixture allows you to link as many as 16 fixtures together and operate without a controller In Master Slave mode the first fixture will control the others to give an automatic sound activated synchronized light show This function is good for when you want an instant performance The first or master fixture s DMX input will have nothing connected to it Its output connects to the slave fixtures which will be set in slave mode automatically 7 DMX512 Configuration 8 IR Remote Control DMX a Values 3 Channel Mode wn ewe CSRs DMX Channel Values 6 c Channel Mode 70 128 Pulse strobe from slow to fast eNom 33 191 E strobe fading in from slow to fast 192 195 DMX Channel Values T Channel Mode 8 1 IR Remote Control Keypad 08 ommen OOOO 66 69 N i 129 132 None Cd 133 191 Strobe fading in from slow to fast 196 255 Strobe fading out from slow to fast In stand alone mode running speed from CHf gt 60 slow to fast CH6 0 255 Static color select Static color mode CH6 0 255 Strobe from slow to fast color change mode
7. installed to avoid vibration while operating Always ensure that the structure to which you are attaching the unit 1s secure and is able to support a weight of 10x this fixture s weight 35 2 Ibs Always use a Safety cable that can hold 12x the weight of the fixture 4 How to Connect the Fixture 3 Pin and 5 Pin XLR DMX Connectors Some manufactures use 5 pin XLR connectors for data transmission in place of 3 pin 5 pin XLR fixtures may be implemented in a 3 pin XLR DMX line When inserting standard 5 pin XLR connectors into a 3 pin line a cable adapter must be used The chart below details the correct cable conversion Bn XLR socket Ae GND screen 3 Pin XLR socket Pin 1 GND laren Pin 2 Signal Pin 3 Signal 5 Pin XLR socket 3 Pin XLR socket f Pin 1 GND preen Pin 1 Eed e i Pin 2 Signa Bin 2 Signal i Pin 3 Signal g 2 Pin 3 Signal Pin 4 N Pin 5 N C 5 DMX512 Connections DMX512 is a widely used protocol for intelligent lighting control with 512 available channels Even if you do not wish to operate your Talent lighting fixture via an outboard DMX controller utilizing the master slave mode will still require unit to unit connection by proper DMX cables Caution Common microphone cables may be used to connect small numbers of DMX fixtures over short distances but offer the risk of erratic operation Use of correct DMX cables greatly reduces data errors caused by improper connection
8. s To go backward in the selected function or reduce parameters To go into the next layer menu 6 2 Main Function Addr LHnd SLALU Siir UNP Pde HUEL LULU nni bind d OP AU PARS ie StH SCH LH Ti HES cH Pod 3 SP PSP B dol eR PLO OY Pigg Pid IS LOLLI i FLUE ta ttt Gee GU bas Duo Tul eS BLIN HES DMX512 Address DMA channel select Waster mode Slave mode Sound mode select Sound sensitivity adjust Hop change mode Strobe speed adjust Gradual change speed adjust AUTO show Static colour select Strobe speed adjust Manual mode RED dimmer Manual mode GREEN dimmer Manual mode BLUE dimmer Normal Shade Mammal InWwersion Your Talent Sound amp Lighting fixture may be operated as a stand alone device that runs on pre programmed routines or sound activation in master slave mode with other devices or via an external DMX512 controller In DMX mode it is configurable to be controlled by 3 5 or 7 channels Besides stand alone operation there are two main ways to control the fixture A Universal DMX control mode B Master Slave operation A Universal DMX controller This fixture s DMX address can be set remotely by a universal DMX controller First you need to program two scenes into a chase and then link the fixtures to the universal DMX controller When you run the chase the fixtures in the chain will set the series DMX address automatically Each lighting fixture n
9. talent talentaudio com LP64LED FLAT Slim Par 64 LED Light DMX Controllable with Remote User Manual YS DMx512 ACTIVATED J sCSY Please read the instructions carefully prior to use TABLE OF CONTENTS 1 Safety Instructions 2 Technical Specifications 3 Installation 4 How to Connect the Fixture 5 DMX512 Connections 6 How to Set the Unit 7 DMX Configuration 8 IR Remote Control 9 Troubleshooting 10 DMX General Information 1 Safety Instructions e Please keep this User Manual for future consultation If you sell the fixture be sure to include this instruction booklet to ensure proper maintenance and use e Unpack and check carefully for transportation damage before using the fixture Before operating ensure that the power supply voltage and frequency match the power of your electrical system e It s important to connect the yellow green conductor to ground to avoid electric shock e Disconnect main power before servicing and maintenance e Use a safety cable when permanently mounting this fixture Always handle the fixture with care e Maximum ambient temperature is 104 F e In the event of a serious operating problem stop using the fixture immediately Please contact the dealer from whom you purchased the fixture the nearest authorized technical repair facility or Talent Sound amp Lighting directly e Do not connect the device to any dimmer pack e Do not touch exposed wires during
Download Pdf Manuals
Related Search