Owner`s Manual - Woodland Direct
Contents
1. Crystal Fire oa User Manual for CF 20 CF 1224 CF 2424 CF 1242 CF 1242 L CF 1264 CF 12120 NF 16 NF 1919 NF 737 NF 719 custom burner sizes CAUTION DO NOT DISCARD THIS MANUAL GAS FIRED e Important operating and maintenance instructions included ng 3 ie c US Read understand and follow these instructions LISTED for safe installation and operation HOT DO NOT TOUCH If the information in these instructions SEVERE BURNS MAY RESULT is not followed exactly a fire or CLOTHING IGNITION MAY RESULT explosion may result causing property Glass and other surfaces are hot damage personal injury or loss of life during operation and cool down e Do not store gasoline or other flammable vapors or Keep children away liquids in the vicinity of this or any other appliance CAREFULLY SUPERVISE children near this e What to do if you smell gas appliance Do not try to light any appliance Alert children and adults to hazards of high Do not touch any electrical switch Do not temperatures use any phone in your building Keep clothing furniture draperies and Immediately call your gas supplier from a other combustibles away neighbor s phone Follow the gas supplier s instructions ZN wrm A If you cannot reach your gas supplier call the For outdoor use only fire department e Installation and service must be performed by a qualified installer service agency or the gas supplier Installation and service of th2. For Outdoor GreatRoom Company gas valves and Outdoor GreatRoom Co Control panel kit control panels this is the lower fitting OR Using two wrenches one to hold the valve ull gt To burn and one to turn the valve fitting Tighten A pan mn _ gt Ww f i out to burner P 1 With burner in place in Outdoor p a aS oE k KS securely If not using this type of valve the Hogs ball valve can be used as shown at E AHAAA 3 Locate the metal flex line gas hose and RK Ball valve tighten securely to the top valve fitting i following the method described in step 2 4 Using two wrenches securely tighten the flare nut on the free end of the metal flex hose to the orifice on the burner 5 For liquid propane installations the air shutter may be left open as shown at right to prevent sooting To adjust air shutter gt gt loosen the small securing screw and rotate air shutter to allow more or less airflow tela Closing the shutter will produce a more we oe i L D Venturi Air shutter yellow flame but may soot Orifice Flare Nut Gas Setup for Natural Gas With burner in place in Outdoor GreatRoom Company fire pit table or other installation location and proper sized orifice inserted in burner neck see chart on p 4 for natural gas orifice sizing adjust air shutter to a closed position as shown at right no light visible through the shutter by loosening the small screw o
3. 3 1 Clearances to Combustibles Page 7 www outdoorrooms com Crystal Fire 42435 REV K 12 30 14 C Framing Enclosure for LP Gas Supply System If you build an enclosure for an LP gas cylinder follow these recommended specifications and local codes Ventilation Enclosures must be ventilated by openings at the level of the cylinder valve and at floor level Effectiveness must be determined with the cylinder s in place One side of the enclosure must be completely open or For an enclosure having four sides a top and a bottom At least two ventilation openings at cylinder valve level shall be provided in the side wall equally sized spaced at 180 degrees 3 14 rad and unobstructed Each opening must have a total free area of not less than 1 2 square inch per pound 3 2 sq cm kg of stored fuel capacity and not less than a total free area of 10 square inches 64 5 sq cm Ventilation opening s must be provided at floor level and shall have a total free area of not less than 1 2 square inch per pound 3 2 sq cm kg of stored fuel capacity and not less than a total free area of 10 square inches 64 5 sq cm If ventilation openings at floor level are in a side wall there must be a least two openings The bottom of the openings must be at floor level and the upper edge can t be more than 5 in 127 mm above the floor The openings must be equally sized spaced at 180 degrees 3 14 rad and unobstructed E
4. Location on appliance Dealer purchased from Dealer Phone Notes Listing Label Information Location The model information regarding your specific appliance can be found on the rating plate attached to your burner via a metal chain See the sample rating plate below for locations of specifications Qs aaeoa Mian Siver Bar Raamaa a Model _ _ Fuel Type o gt Orifice Size arar ju wth this applanca Far Gansun a quaifod metaller sorvico Serial no Page 2 www outdoorrooms com Crystal Fire 42435 REV K 12 30 14 Table of Contents Listing and Code Approvals 5 Appliance Setup a Appliance certification a Burner assembly b BTU specifications b Glass installation Getting Started 6 Operating Instructions a Design and installation considerations a Before lighting b Tools and supplies required b Lighting the fire c Inspection of appliance and components c After the fire is lit d Step by step lighting instructions 7 Finishing Framing Clearances 8 Converting to Natural Gas a Selecting a location 9 Troubleshooting b Required clearance to combustibles 10 Maintaining and servicing the appliance c Framing an enclosure for LP supply system 11 Reference Materials Fuel Information a Service parts list a Fuel b Limited one year warranty b Gas pressure c Contact information c Gas connection d LP Gas supply P
5. Do NOT use this appliance if any part of it has been underwater Have a qualified service technician inspect the appliance and replace any part of the control system and any gas control which has been underwater CAUTION Sharp Edges Wear protective gloves and safety glasses during installation Do not burn solid fuels in this gas appliance Inspect the Appliance and Components Inspect appliance and components for damage Damaged parts may impair safe operation e Do NOT install damaged incomplete or substitute components Report damaged parts to your dealer e Carefully remove all burner components from packaging e Read all instructions before beginning installation Follow these instructions carefully during installation to ensure maximum safety and benefit Crystal Fire 42435 REV K 12 30 14 aming and C S Note WARNING e Illustrations reflect typical installations A n Fire Risk and are FOR DESIGN PURPOSES ONLY e Illustrations diagrams are not drawn to Provide adequate clearance scale e Around air openings e Actual installation may vary due to e For service access individual design preference Locate appliance away from traffic areas If you are not using an Outdoor GreatRoom Company table with 72 this burner be sure to mount to a non combustible surface maintaining at least 8to combustible surfaces and framing below the surface of burner Figure
6. THE PRODUCT Some states do not allow limitations on how long an implied warranty lasts or do not allow exclusion or limitation of incidental or consequential damages so these limitations may not apply to you To obtain service under this warranty you must 1 Send written notice of the claimed condition to The Outdoor GreatRoom Company 2015 Silver Bell Road 195 Eagan MN 55122 2 Affirm that you are the original owner of the Product 3 Provide The Outdoor GreatRoom Company reasonable opportunity to investigate the claim including reasonable opportunity to inspect the Product prior to any repair or replacement work and before the Product or any component of the Product has been removed Page 19 www outdoorrooms com Crystal Fire 42435 REV K 12 30 14
7. accidental damage DO NOT BURN WITHOUT GLASS OR OTHER SUBSRATE SUCH AS LAVA ROCK IN BURNER Crystal Fire 42435 REV K 12 30 14 C Igniter Installation and Grounding Note Before installing ignition system ensure that gas valves are closed and gas is disconnected for safety Control Panel Sparker Or other thin surface ENA Ground wire ert mery Hex Nut Sporker Cop Sparker 1 A grounding wire is included with your burner as shown above This can be plugged into either port on the back side of the sparker 2 A spark wire hangs from the electrode at the end of the burner also above This can be plugged into the remaining open port on the back side of the sparker to complete igniter hookup Note It doesn t make a difference which port the wires are plugged into as long as they are both plugged in A battery AAA type should be installed in the igniter before use The battery s positive end should face outward when installed Page 10 www outdoorrooms com Crystal Fire 42435 REV K 12 30 14 5 Gas Hookup A Fuel Before making gas connections ensure the appliance being installed is compatible with the available gas type Gas Pressure Proper input pressures are required for optimum performance Gas line sizing requirements need to be made following NFPA54 Fire Risk Explosion Risk Verify inlet pressures e High pressure may cause overfire condition Low pressure may cause explos
8. age 3 www outdoorrooms com Crystal Fire 42435 REV K 12 30 14 What s included CF20 NF 16 Round burner assembly Black propane hose with regulator Flexible metal gas line Piezoelectric igniter 43 Orifice LP 31 Orifice NG 2 bags of decorative glass Rectangular Burner Assembly Black propane hose with regulator Flexible metal gas line Piezoelectric igniter 31 Orifice LP 21 Orifice NG 3 bags of decorative fire glass Two piece burner assembly e Black propane hose with regulator Manifold kit T connector and flexible metal hose 2 Flexible metal gas lines Piezoelectric igniter 31 Orifice x2 LP 21 Orifice x2 NG 6 bags of decorative fire glass CF 1224 NF 719 Rectangular Burner Assembly Black propane hose with regulator Flexible metal gas line Piezoelectric igniter 43 Orifice LP 31 Orifice NG 2 bags of decorative glass Rectangular Burner Assembly Black propane hose with regulator Flexible metal gas line Piezoelectric igniter 31 Orifice LP 21 Orifice NG 4 bags of decorative fire glass Page 4 www outdoorrooms com CF 2424 NF 1919 Square burner Assembly Black propane hose with regulator Flexible metal gas line Piezoelectric igniter 36 Orifice LP 17 Orifice NG 4 bags of decorative fire glass Two piece rectangular burner assembly Black propane hose with regulator Manifold kit T connector and 2 flexible metal hoses Piezoelectr
9. aged The replacement burner assembly specified by the manufacturer Position the assembly in the desired location This loca tion must be adjacent to the gas supply line You must have easy access to the gas valve control knob after it is installed and connected to the gas supply because the ON OFF gas valve is used to turn the burner on and off B Glass Installation Spread glass out evenly over burner area Use all glass provided for best affect Keep glass clear of spark to avoid accidental blockage Note A percentage of glass beads may arrive split in half This is normal Additional beads may split after use This is also normal due to the physical properties of glass Page 9 www outdoorrooms com LP Gas Models e Make sure the tank valve is turned completely off clockwise e Ensure the tank valve has the proper external mating threads tank valve marked USE WITH TYPE 1 e Inspect the hose shipped with the appliance for any damage Do not use if there is evidence of damage e Connect the end of the hose onto the ON OFF gas valve of the appliance Make sure it is secured tightly e Connect the regulator assembly to the tank valve Hand tighten only clockwise Do not use a wrench to tighten Use of a wrench may damage the quick closing nut and result in a hazardous condition e Position the hose out of pathways where people might trip over it or in areas where the hose might be subject to
10. be those specified in this manual natural gas line or LP gas cylinder e The LP gas supply cylinder used with LP models must be e The LP gas cylinder supply system must be constructed and marked in accordance with the arranged for vapor withdrawal specifications for LP gas cylinders of the U S Department of Transportation DOT e The LP gas cylinder used must include a collar to protect the cylinder valve e Cylinders must be stored outdoors in a well ventilated area out e When an LP model is not in use the LP gas must of the reach of children Disconnected cylinders must have be turned off at the supply c linder threaded valve plugs tightly installed and must not be stored pee i in a building garage or any other enclosed area e The specific size and capacity of the cylinder s to be used 20 Ib or hard plumbed to propane tank IMPROPER INSTALLATION ADJUSTMENT ALTERATION SERVICES OR MAINTENANCE CAN CAUSE INJURY OR PROPERTY DAMAGE REFER TO AND UNDERSTAND THIS MANUAL FOR ASSISTANCE OR ADDITIONAL INFORMATION CONSULT A QUALIFIED INSTALLER SERVICE AGENCY LICENSED TECHNICIAN OR THE GAS SUPPLIER Gas Setup for Liquid Propane lt i GreatRoom Company fire pit table or other installation location and proper sized orifice inserted in burner neck see chart on p 4 for orifice sizing locate flexible rubber propane hose and regulator supplied with this burner 2 Attach the propane hose to incoming gas fitting on the gas valve
11. d and removed from the appliance Obstructions of combustion and venti lation air The use of a vinyl table cover is highly recommended to keep your table and burner looking new and ensuring extended trouble free operation Risk of injury or property damage Condition of burner assembly Bumer ignition and operation Bumer air shutter adjustment Gas connections and fittings Risk of Fire Before servicing g Delayed ignition or explosion Tum off utilities to appliance Exposure to combustion fumes Ensure appliance is completely cooled Odors Maintenance and Service Tasks For service calls Contact the dealer your product was purchased from first Contact the Outdoor GreatRoom Company at 1 866 303 4028 if further assistanc Inspect Maintenance Tasks Burner Assembly Remove decorative glass and examine burner Vacuum and wipe out as needed Use caution when cleaning these areas el Inspect for warping and corrosion Repair as necessary 3 Check the hose connecting the LP gas cylinder to ensure it is not damaged Replace as necessary Verify air shutter area is clean Burner Ignition and Operation 1 Verify all gas connections are tight and leak free Clean burner top inspect for plugged ports corrosion or deterioration Replace burner if necessary 3 Inspect for flame problems Verify air shutter is clear of dust and debris and is in correct position for the gas t
12. door GreatRoom Company Any of the circumstances described in the previous sentence voids this warranty This warranty is void if the Product or any component has been removed repaired or replaced before The Outdoor GreatRoom Company has been afforded a reasonable opportunity to inspect the Product This warranty is limited to the replacement or repair of defective components or workmanship and The Outdoor GreatRoom Company may fully discharge its obligations under this warranty by repairing or replacing at its discretion the defective components The Outdoor GreatRoom Company will provide replacement parts at no charge and will pay reasonable and necessary labor and freight costs related to replacing or repairing defective components under this warranty The maximum amount recoverable under this warranty is limited to the purchase price of the Product and if The Outdoor GreatRoom Company is unable to provide replacement or repair in an expedient and cost effective manner The Outdoor GreatRoom Company may discharge all obligations under this warranty by refunding the purchase price of the Product EXCEPT TO THE EXTENT PROVIDED BY LAW THE OUTDOOR GREATROOM COMPANY MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSED HEREIN THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO THE DURATION OF THE WARRANTY SPECIFIED ABOVE IN NO EVENT SHALL THE OUTDOOR GREATROOM COMPANY BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY DEFECTS IN
13. es Sparker is improperly grounded Refer to section 4 C on Page 9 for grounding instructions Check Sparker makes clicking all wire connections sound but no visible spark is produced Ignition or ground wire not plugged in Check that tip of sparker is within 1 of grounding probe Gently Igniter tip set too far from grounding probe bend igniter tip or grounding probe by hand to achieve a smaller gap Ensure that a fresh AAA battery is installed Positive side facing Battery low Not installed Installed incorrectly outward toward the sparker cap Check contact at the bottom of the battery cavity for corrosion rker does not spark Speer ose DO Spalk ot Clean with a small piece of sandpaper or a file make a ticking sound Corrosion on battery contacts Ifthe cap cannot be screwed down tight enough the battery will not make a proper connection with the sparker and it will not work Be sure to use a thin surface such as 20 22gauge sheet metal to mount sparker in Battery cap not screwed down completely Page 16 www outdoorrooms com Crystal Fire 42435 REV K 12 30 14 Although the frequency of appliance servicing and maintenance will depend on use and the type of installation a qualified service technician should perform an appliance check up annual Annual inspection by qualified technician recommended Storage of an appliance indoors is permissible only if the cylinder is Check disconnecte
14. ic igniter 31 Orifice x2 LP 21 Orifice x2 NG 8 bags of decorative fire glass Crystal Fire 42435 REV K 12 30 14 A Appliance Certification MODEL CRYSTAL FIRE CF 20 CF 1224 CF 2424 CF 1242 L NF 1919 NF 719 NF 737 NF 16 CF 1264 CF 12120 LABORATORY Underwriters Laboratories Inc UL TYPE Decorative Gas Fired Outdoor Fireplace STANDARD Out Decorative Gas Appliances ANSI 221 97 2014 CSA 2 41 2014 The Crystal Fire has been tested in accordance with ANSI Z21 97 2014 and CSA 2 41 2014 for Canada and has been listed by Underwriters Laboratory UL for installation and operation as described in these installation and operating instructions The installation must conform with local codes or in the absence of local codes ANSI 2223 1 NFPA 54 National fuel gas code Natural gas and propane installation code CSA B149 1 or propane storage and handling code CSA B149 2 Page 5 www outdoorrooms com B BTU Specifications Model Orifice Size Max input BTU P NG wp NG CF 20 NF 16 43 31 55331 51706 CF 1224 NF 719 43 31 55331 51706 CF 2424 NF 1919 36 417 79229 107465 CF 1242 NF 737 31 a 100588 90776 CF 1264 31 100588 90776 CF 12120 CF 1242 L 312 2112 100588 per half 90776 per half Crystal Fire 42435 REV K 12 30 14 2 Getting Sta
15. ion Verify minimum pressures when other household gas appliances are operating Install regulator upstream of valve if line pressure is greater than Pressure requirements for appliance are shown in table below Minimum pressures must be met when other household gas appliances are operating Pressure Natural Gas Minimum Inlet Pressure 7 in w c 11 in w c Maximum Inlet Pressure 10 5inw c 14 in w c The appliance and its individual shutoff valve must be dis connected from the gas supply piping system during any pressures in excess of 1 2 psi 3 5 kPa The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1 2 psi 3 5 kPa C Gas Connection Note Have the gas supply installed in accordance with local building codes if any If not follow ANSI 223 1 Installation should be done by a qualified installer approved and or licensed as required by the locality In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas fitter Page 11 www outdoorrooms com and Informatio Note A listed and Commonwealth of Massachusetts approved 3 8 in T handle manual shut off valve and flexible gas connector are connected to the 3 8 in control valve inlet If substituting for these component
16. is appliance Improper installation adjustment alteration service or should be performed by qualified personnel The Outdoor GreatRoom maintenance can cause injury or property damage Read Company suggests NFI certified factory the installation and maintenance instructions professionals or technicians supervised thoroughly before installing or servicing this equipment by an NFI certified professional Read this manual before installing or operating this appliance Please retain this owner s manual for future reference Congratulations Congratulations on selecting an Outdoor GreatRoom Company decorative gas appliance The Crystal Fire you have selected is designed to provide the utmost in safety reliability and efficiency As the owner of a Crystal Fire you ll want to read and carefully follow all of the instructions contained in this owner s manual Pay special attention to all cautions and warnings This owner s manual should be retained for future reference We suggest you keep it with other important documents and product manuals This information contained in this owner s manual unless noted otherwise applies to all models and gas control systems Your new Crystal Fire will give you years of durable use and trouble free enjoyment Homeowner Reference Information We recommend that you record the following pertinent information about your appliance Model name Date of purchase installation Serial Number
17. n the air shutter and rotating it toa closed position and re tightening screw Locate the included metal flex line hose and thread one end onto orifice and tighten securely with two wrenches At this point you have two options for plumbing natural gas If using a valve assembly such as The Outdoor GreatRoom Company s valve kit proceed to step 3a If plumbing directly to a natural gas line proceed to 3b a Attach the free end of flex hose to the top outgoing flare fitting of control valve and tighten fully with two wrenches Plumb incoming natural gas to the incoming side of the valve using a 3 8 flare nut It is strongly recommended that a manual shutoff valve is placed in the natural gas line before it reaches the fire pit s control valve b Thread the included ball valve onto the free end of the metal flex line and plumb incoming natural gas line to the ball valve with a 3 8 flare nut Saas Lats Wiii Flare Nut S jamm Outdoor GreatRoom Co Control panel kit To burner 25 ure _ a cori as Ball valve CHECK ENTIRE SYSTEM FOR LEAKS BEFORE OPERATING Page 13 www outdoorrooms com Crystal Fire 42435 REV K 12 30 14 Lighting and operation FOR YOUR SAFETY READ BEFORE LIGHTING WARNING If you do not follow these instructions exactly a fire or explosion may result causing property damage personal injury and or loss of life A This appliance can be lit elec
18. om Key Largo fire pit with CF 1242 burner Napa Valley fire pit table with CF 1224 burner ierra fire pit table Uptown fire pit table with with CF 2424 burner CF 1224 burner Page 15 www outdoorrooms com Crystal Fire 42435 REV K 12 30 14 Sar Possible Causes Corrective Actions No LP in tank or NG main not turned on Check the LP propane tank You may be out of gas Or check Natural Gas valve at main Plugged burner orifice Check the burner orifice for stoppage Remove stoppage Manual shutoff valve on off control knob open Close LP tank and manual shutoff valves Open LP tank valve or not in stalled between LP tank and first THEN the manual shutoff valve appliance This is a result of normal operation and flames will begin to yellow as unit is allowed to burn for Do nothing 16 20 minutes Improper air fuel mixture related to air shutter position Noise is caused by metal expanding and contracting as it heats up and cools down similar to the sound produced by a furnace or Do nothing heating duct This noise does not affect the operation or longevity of the appliance This is a property of glass and may happen occasionally Do nothing This is completely normal Crystal Fire won t light Low flames or won t stay lit Blue Flames Close air shutter for LP leave 1 4 open Natural gas 1 16 open Metallic noise Decorative Beads cracking of spitting Heat and or abrupt temperature chang
19. rted This appliance is a Decorative Gas Appliance for OUTDOOR USE ONLY and MUST NOT be used for cooking Place the Crystal Fire on a flat and stable surface in an outdoor location such as a patio or deck This location must be adjacent to the gas supply line or LP gas supply cylinder DO NOT locate the appliance where it will get excessively wet or submerged in water A Design and Installation Considerations When planning an appliance installation it s necessary to determine the following information before installing e Where will the appliance be installed See section 3 Gas supply piping e Framing and finishing details See sections 3 7 B Tools and Supplies Required Before beginning the installation be sure that the following tools and supplies are at hand e Gloves See section 4 e Safety Glasses e Phillips screwdriver e Non corrosive leak check solution e Wrenches e 1AAA battery The Outdoor GreatRoom Company disclaims any responsibility for and the warranty will be voided by the following actions Installation and use of any damaged components Modification of the burner assembly Installation other than as instructed by the Outdoor GreatRoom Company Any such action may cause a fire hazard Page 6 www outdoorrooms com Asphyxiation Risk e This gas appliance is for outdoor use in a well ventilated space This unit must not be installed inside an enclosed structure or unvented appliance
20. s please consult local codes for compliance Incoming gas line should be piped to the inch connection on the manual shutoff valve Risk Explosion Risk e Gas build up during line purge may ignite Purge should be performed by qualified technician Ensure adequate ventilation Ensure there are no ignition sources such as sparks or open flames e Asmall amount of air will be in the gas supply lines When first lighting appliance it will take a short time for air to purge from lines Subsequent lighting of the unit will not require such purging Never allow the ON OFF valve to remain in the open position without pressing and continuing to hold igniter button FIRST CHECK FOR GAS LEAKS Fire Risk Explosion Risk Asphyxiation Risk e Check all fittings and connections e Do not use open flame e After the gas line installation is complete all connections must be tightened and checked for leaks with a commercially available leak sheck solution Be sure to rinse off all leak check solution Be sure to rinse off all leak check solution following testing Fittings and connections may have loosened during shipping and handling Crystal Fire 42435 REV K 12 30 14 D LP Gas Supply e The pressure regulator and hose assembly supplied with LP e Storage of this appliance indoors is permissible only models must be used Replacement pressure regulators and if it has been disconnected from its fuel supply hose assemblies must
21. spect the appliance and replace any part which has been underwater E The gas pressure regulator provided with this appliance must be used This regulator is set for an outlet pressure of 10 5 inches water column yo Pg 1 4 gap i Ss Igniter button To Extinguish Turn control valve to OFF position or close ball valve Close valve on propane tank while not in use Initial break in procedure When you light the appliance you may notice that it produces heat which may have an odor If you feel this odor is excessive it may require an initial three to four hour continuous burn on high age 14 www outdoorrooms com Crystal Fire 42435 REV K 12 30 14 FIRE RISK HIGH TEMPERATURES Keep combustible household items away from appliance Do NOT obstruct combustion and ventilation air Do NOT place combustible items on top of or near appliance Keep furniture draperies away from appliance Do NOT use lantern fuel kerosene charcoal lighter fluid or similar liquids in this appliance Combustible materials flammable liquids or vapors may ignite Personalize your Crystal Fire by building a decorative surround from noncombustible material such as bricks landscaping blocks or rocks The Outdoor GreatRoom Company also sells a variety of fire pit tables to fit each of our burners as shown 42 Black Glass fire pit table below not all models shown see more at with CF 20 burner OutdoorRooms c
22. tion to or inconsistent with the terms of this warranty This warranty gives you specific legal rights You may also have other rights that vary from state to state The Outdoor GreatRoom Company warrants that this Outdoor GreatRoom Outdoor Product the Product will be free from defects in material and workmanship for a period of one year from its date of purchase Stainless steel parts and assemblies carry a limited lifetime warranty This warranty is subject to the conditions exclusions and limitations described below This warranty applies only to the original owner of the Product and is non transferable The Outdoor GreatRoom Company obligation under this warranty does not extend to damages resulting from 1 assembly operation or maintenance of the Product not in accordance with the Installation Assembly Instructions Operating Instructions and the Listing Agency Identification Label furnished with the Product 2 installation or use which does not comply with local building codes and ordinances 3 shipping improper handling improper operation abuse misuse accident or unworkmanlike repairs 4 use of fuels other than those specified in the Operating Instructions 5 Installation or use of components not supplied with the Product or any other components not expressly authorized and approved in writing by The Outdoor GreatRoom Company and or 6 modification of the Product not expressly authorized and approved in writing by The Out
23. tronically or with a match When lighting follow these instructions exactly B Before lighting smell all around the appliance area for gas Be sure to smell next to the base of the appliance because some gas is heavier than air and will settle on the floor WHAT TO DO IF YOU SMELL GAS e Donottry to light any appliance e Do not touch any electric switch do not use any phone nearby e Immediately call your gas supplier from a neighbors phone Follow gas supplier s instructions e Ifyou cannot reach your gas supplier call the fire department 1 Depress button on igniter and verify a spark is being produced between the electrode tip and receiving probe Ensure control panel valve is in the OFF position 2 and slowly open valve on propane tank If using natural gas or whole house LP open ball valve If not using a control valve skip this procedure until step 3 3 Depress igniter button and continue holding button while turning control valve or ball valve if not using a control knob valve to the on position Release button once flame is present C Use only your hand to turn the gas control knob on propane tank if equipped never use tools If the valve won t turn by hand don t try to repair it call a qualified service technician Force or attempted repair may result in a fire or explosion D Do not use the appliance if any part has been underwater Immediately call a qualified service technician to in
24. very opening must have minimum dimensions to permit the entrance of a 1 8 inch 3 2 mm diameter rod Page 8 www outdoorrooms com Acc essibility Cylinder valves must be readily accessible for hand operation A door on the enclosure to gain access to the cylinder valves is acceptable provided it is non locking and can be opened without the use of tools The design of the enclosure must be such that The LP gas supply cylinder s can be connected connections disconnected and the inspected and tested outside the cylinder enclosure Those connections which could be disturbed when installing the cylinder s in the enclosure can be leak tested inside the enclosure Be certain to mount or set the LP gas cylinder on a flat stable surface and retain it to prevent it from tipping Minimum Clearances e There must be a minimum clearance of 2 in 50 8 mm between the lower surface of the floor of the LP gas supply cylinder enclosure and the ground Crystal Fire 42435 REV K 12 30 14 A Burner Assembly All Models Check for damage Do not use damaged components The hose assembly must be replaced prior to the ap pliance being put into operation if there is evidence of excessive abrasion or wear or if the hose is damaged The replacement hose assembly specified by the man ufacturer The burner must be replaced prior to the appliance be ing put into operation if it is evident that the burner is dam
25. ype being used 5 Inspect orifice for soot dirt or corrosion 6 Verify manifold and inlet pressures Adjust regulator as required Gas Hose with Regulator The gas hose with regulator supplied with appliance must be used for LP installations The replacement bust be those specified by the appliance manufacturer Page 17 www outdoorrooms com Crystal Fire 42435 REV K 12 30 14 10 Reference Materials A Service Ports List Description of Part Part Number Stainless Steel Flex Line FE ies KA e Res hanced replacement bal ave ov SE 9 Control panel for DIY or Outdoor GreatRoom Co fire pit tables Electronic Piezo 16 NF 719 NF 737 Ignition Electrode CF 2424 NF 1919 CF 1242 L Replacement Glass for Crystal Fire 5lb bag 1 CAITE 7 Grounding wire for Crystal Fires All models 1 nA OutdoorGreatRoom company For more information you can visit us online at Http www OutdoorRooms com Or Call Us At 1 866 303 4028 Page 18 www outdoorrooms com Crystal Fire 42435 REV K 12 30 14 B Limited One Year Warranty e TA The Outdoor GreatRoom Company Outdoor GreatRoom Outdoor Products Limited Warranty company The Outdoor GreatRoom Company extends the following warranty for Outdoor GreatRoom outdoor products used in the United States of America or Canada Dealers and employees of The Outdoor GreatRoom Company have no authority to make any warranty or authorize any remedies in addi
Download Pdf Manuals
Related Search