SIMADYN D Digital Control System SS52 Interface Module
Contents
1. Cabinet ground connection Siemens AG Dk No 247463 Edition 04 97 9 SIMADYN D Hardware User Manual Drives and Standard Products Variable Speed Drives Division Postfach 3269 D 91050 Erlangen System Based Drive Technology Edition 04 97 Siemens AG Dk No 247463 SIMADYN D Hardware User Manual2. which can be switched in Please refer to the SINEC Industrial Communications Catalog IK10 1996 for information regarding SINEC L2 DP as well as the components required to configure a bus system 5 2 Monitor interface A hexadecimal monitor runs in parallel on the SS52 in the background Parameter data of the PROFIBUS are loaded using the hexadecimal monitor When a fault error condition develops diagnostics is possible via the hexadecimal monitor so that they can be quickly localized and removed For space reasons this interface is located at the same connector as for the PROFIBUS interface The monitor interface is an RS232 interface and cannot be modified 4 Edition 04 97 Siemens AG Dk No 247463 SIMADYN D Hardware User Manual 6 Application information 6 Application information The interface module can be configured in any slot of the CS7 subrack A maximum of three interface modules can be configured for each CS7 No specific sequence has to be followed The board must be screwed to the guide rails for perfect functioning even during start up If the board is inserted in an adapter the front panel must be connected to the rack housing through a short cable The board may neither be inserted nor withdrawn under voltage 7 Shielding The bus cable shield must be grounded through the largest possible surface area where the cable enters the cabinet The cable shield must be connected to the grounding rail where the cab
3. DD1688 0AE2 SS52 interface board 3 Description The SS52 board is an interface board for the SINEC L2 DP PROFIBUS protocol It is inserted into one of the three slots of the CS7 subrack corresponding to the actual configuration A maximum of three modules can be inserted in each support board The interface module has a serial RS485 interface conforming to the PROFIBUS Standard This interface is floating electrically isolated The interface is physically located at the 9 pin sub D socket connector X5 The connection to the support board is established via the CS7 SS4 SS5 1 parallel interface at the 48 pin plug connector X1 In addition to the data address and control bus this connection is also used to connect the 5 V 15 V and 15V module power supply Data transfer with the processor boards is realized via a 16 kbyte dual port RAM which is located on the support board A double test socket and a double LED assigned to each slot are provided on the support board The LEDs have the following function H10 H20 H30 H11 H21 H31 bright dark flashing Significance of the function refer to PROFIBUS DP Instruction Manual In addition to the reset function by the power supply a local reset can be initiated by short circuiting jumpering the two test sockets at the processor of the appropriate interface module This function has no effect on the remaining subrack It is required for the software test and fault find
4. SIMADYN D User Manual Digital Control System SS52 Interface Module Edition 04 97 DK No 247463 User Manual SS52 Interface Module SS52 Interface Module 02 96 SS52 Interface Module 04 97 Copying of this document and giving it to others and the use or communication of the contents thereof is forbidden without express authority Offenders are liable to the payment of damages All rights are reserved in the event of the grant of a patent or the registration of a utility model or design We have checked the contents of this Manual to ensure that they coincide with the described hardware and software However deviations cannot be completely ruled out so we cannot guarantee complete conformance However the information in this document is regularly checked and the necessary corrections included in subsequent editions We are thankful for any recommendations or suggestions Contents Contents le Warningsiniormation iss iv in naco od dan A es ee ete ota 1 2 gt Ordenng AVA ken naeh at av e be AT 3 3 D SON PWO Ayen ao arten Ronnie 3 4 Sforzi e Be l loje jq tb yb por fa ee eee eee eet 4 HE SOMAl inte ACS eu tert aki hha a aa Tae aaa Ta Ta oo aa a taa aa ta Ta Tata ah A 4 BASSINEC EZ DP ante e a a a a a e a qa a aa e Ja e aed 4 5 23 Monitor inten acest aa a do 4 6 Application information Mar A fi tata ta fede ija fa ea ada ada a a oka 5 FeSHICMING sc ile eA do 5 8 Additional omponenti oye y si vey a ira nanan hain
5. annel B Opto coupler DC DC EEPROM e LED 32Kbyte He Service interface Signal level conv RS 232 RS485 48 pin parallel bus connector X1 Serial interface 9 pin sub D X5 Fig 1 SS52 block diagram 8 Edition 04 97 Siemens AG Dk No 247463 SIMADYN D Hardware User Manual 13 ESD instructions 13 ESD instructions Components which can be destroyed by electrostatic discharge ESD Generally electronic boards should only be touched when absolutely necessary The human body must be electrically discharged before touching an electronics board This can be simply done by touching a conductive grounded object directly beforehand e g bare metal cubicle components socket outlet protective conductor contact Boards may not come into contact with highly insulating materials e g plastic foils insulated desktops articles of clothing manufactured from man made fibers Boards may only be placed on conductive surfaces When soldering the soldering iron tip must be grounded Boards and components should only be stored and transported in conductive packaging e g metalized plastic boxes metal containers If the packing material is not conductive the boards must be wrapped with a conductive packing material e g conductive foam rubber or household aluminum foil The necessary ESD protective measures are clearly shown in the following diagram a Conductive floor surface d ESD overall b ESD table e ESD chain c ESD shoes f
6. els Danger indicates death severe personal injury and or substantial property damage will result if proper precautions are not taken WARNING For the purpose of this User Manual and product labels Warning indicates death severe personal injury or property damage can result if proper precautions are not taken CAUTION For the purpose of this User Manual and product labels Caution indicates that minor personal injury or material damage can result if proper precautions are not taken NOTE For the purpose of this User Manual Note indicates information about the product or the respective part of the User Manual which is essential to highlight CAUTION This board contains components which can be destroyed by electrostatic discharge Prior to touching any electronics board your body must be electrically discharged This can be simply done by touching a conductive grounded object immediately beforehand e g bare metal cabinet components socket protective conductor contact WARNING Hazardous voltages are present in this electrical equipment during operation Non observance of the safety instructions can result in severe personal injury or property damage It is especially important that the warning information in all of the relevant Operating Instructions are strictly observed 2 Edition 04 97 Siemens AG Dk No 247463 SIMADYN D Hardware User Manual 2 Ordering data 2 Ordering data SS52 6
7. hina anna hae 5 95 TECHNICANAALA A wey a a 6 10 Connector assignment of the interfaces 0 ss nanna nanna mnnn nanna nnnnnnnnnn 6 10 1s Serial interta e sais 6 10 2 Parallel interface CS7 SSA SSB nanna anna ttmmnmn mnn 7 11 STRUC L mask of the SS52 board in the master program ss ennnnnnnnnnznnnnnnnnnnrnnnnnn nano 7 A i l NA 7 1241 Eiteratures e a a a a Ta a Ta ean een ean a 7 12 2 Attachments us Atti a a itaffi o a tfa o f ff ee A 7 12 21 LAYOUT diagram sass areata age ieee eS 7 1 2 2 2 DIMENSION drawin oca 8 12 2 3 Block dlagram sia 2555524855 hae da 8 1 3 ESB MStUCHUONS e adda ad ts 9 Siemens AG Dk No 247463 Edition 04 97 SIMADYN D Hardware User Manual 1 Warning information Edition 04 97 Siemens AG Dk No 247463 SIMADYN D Hardware User Manual 1 Warning information NOTE The information in this Manual does not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation operation or maintenance Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser s purposes please contact your local Siemens office Further the contents of this Manual shall neither become a part of nor modify any prior or existing agreement committment or relationship The sales contract contains the entire obligation of Siemens The warranty contained in the contract be
8. ing During normal operation it is not permissible to initiate a reset using these sockets Siemens AG Dk No 247463 Edition 04 97 3 SIMADYN D Hardware User Manual 4 Board design PROFIBUS interface operation is indicated by an LED on the interface module It is used for fault finding and commissioning and is not externally visible in normal operation when the module is inserted It has the following function LED bright PROFIBUS interface operation a dark PROFIBUS interface not operational There is an 80 pin test connector X20 on the board for hardware diagnostics using a logic analyzer Correct hardware functioning is monitored using a watchdog 4 Board design The board has the following hardware components 80C186 processor 20 MHz EPROM 256 kbyte with firmware Local processor RAM 256 kbyte Parallel interface to the support board RS485 serial interface Watchdog for NMI monitoring LED for the operating display of the PROFIBUS interface Diagnostics connector for the logic analyzer Diagnostics functionality using the hexadecimal monitor 5 Serial interfaces 5 1 SINEC L2 DP The connection is either realized via the SINEC L2 bus terminal or the SINEC L2 bus connector at the 9 pin Sub D socket connector X5 When using the RS485 bus terminal the cable capacitance must be taken into account dependent on the baud rate Both the bus terminal as well as the bus connector have a terminating resistor
9. le enters the cabinet Further the shield in the connector housing must be connected to the housing The connector must be screwed to the module The SIMADYN D EMC Directives and Installation Guidelines 2 are valid 8 Additional components CS7 subrack 6DD1662 0ABO Following data and additional bus components e g fiber optic cables refer to Catalogs IK10 and ST76 1996 SINEC L2 bus cable e g 6XV1830 0AH10 SINEC L2 DP connector 6ES7972 0BA20 0XA0 12 Mbaud e g Siemens AG Dk No 247463 Edition 04 97 5 SIMADYN D Hardware User Manual 9 Technical data 9 Technical data INSULATION GROUP A acc to VDE 0110 Paragraph 13 Group 2 at 24 V DC 15VDC 5 VDC AMBIENT TEMPERATURE 0 to 55 degrees C for self cooling STORAGE TEMPERATURE 40 to 70 degrees C HUMIDITY CLASS F acc to DIN 40040 ALTITUDE RATING S acc to DIN 40040 MECHANICAL STRESSING Mounted in stationary but not necessarily vibration free equipment PACKAGING SYSTEM Installed in the slot in the CS7 subrack DIMENSIONS 184 65 mm WEIGHT 0 5 kg CURRENT DRAIN P5 07A A ETA pO INT 10 Connector assignment of the interfaces 10 1 Serial interface X5 X5 9 pin Sub D socket connector Pin Designation Explanation ME ES PRFTR Receive and send signal Ready to send 6 PSEXT JPSextemal 8 PRFTR receive andsendsignal 9 RTS Readytosend 6 Edition 04 97 Siemens AG Dk No 247463 SIMADYN D Hard
10. tween the parties is the sole warranty of Siemens Any statements contained herein do not create new warranties nor modify the existing warranty 1 Warning information WARNING Electrical equipment has components which are at dangerous voltage levels If these instructions are not strictly adhered to this can result in severe bodily injury and material damage Only appropriately qualified personnel may work on this equipment or in its vicinity This personnel must be completely knowledgeable about all the warnings and service measures according to this User Manual The successful and safe operation of this equipment is dependent on proper handling installation operation and maintenance Siemens AG Dk No 247463 Edition 04 97 1 SIMADYN D Hardware User Manual 1 Warning information Definitions QUALIFIED PERSONNEL For the purpose of this User Manual and product labels a Qualified person is someone who is familiar with the installation mounting start up and operation of the equipment and the hazards involved He or she must have the following qualifications 1 Trained and authorized to energize de energize clear ground and tag circuits and equipment in accordance with established safety procedures 2 Trained in the proper care and use of protective equipment in accordance with established safety procedures 3 Trained in rendering first aid DANGER For the purpose of this User Manual and product lab
11. ware User Manual 10 2 Parallel interface CS7 SS4 SS5 X1 48 pole connector C OOo A A TE _ k po 9 Ds TC BB 11 STRUC L mask of the SS52 board in the master program STRUC L mask 100 5552 PROFIBUS DP interface module 101 KKK KKK KKK KKK KKK KKK KKK KKK KKK KKK KKK KKK KKK KKK KKK KKK KKK KKK KKK AH AK 12 Others 12 1 Literature 1 DK No 21 43 10 Parallel interface CS7 SS4 SS5 2 DK No 20 10 60 EMC Directives Installation Guidelines 12 2 Attachments 12 2 1 Layout diagram Layout diagram Siemens AG Dk No 247463 Edition 04 97 SIMADYN D Hardware User Manual 35E 465 688 9004 22 AO 12 Others 12 2 2 Dimension drawing Dimension drawing 3SE 465 688 9004 22 MB 12 2 3 Block diagram Block diagram Fig 1 e __ ddress bus Address latch Quart uartz EPROM e e Data bus falla oscillator 512K byte ven e Control bus 40 MHz RAM L 256Kbyte Control LED E YA AN p ki ASPC2 oscillator 48 MHz Chip select Watchdog e NMI e Control logic W at State e LOCK Bus arbitration Pat e a Seria ontroller f l e 85030 Electrical isolation e e Channel A Ch
Download Pdf Manuals
Related Search