USER`S MANUAL
Contents
1. 8 MAINTENANCE AND cee 9 APTERSALES ATTENTIONS Before operating your unit please read the manual thoroughly and severely conform to the operation methods mentioned this manual Otherwise unexpected damage to unit or injury to yourself or others may occur AIR CONDITIONER OPERATION CONDITIONS Temperature Mode Cooling operation Heating operation Room temperature 17 C_ 326 17 C_ 30 C Outdoor temperature 18 C_ 43 C 7 C 24 CAUTION If air conditioner is used beyond the above conditions safety protection features may come into operation or cause dew dripping and affect cooling or heating effect CHECK UP BEFORE OPERATION e Ensure the grounding wire is not broken off and connected well e Ensure the filter is well installed Before you restart a long period unused air conditioner please clean the filter first Refer to Maintenance and cleaning for details e Ensure the outlet and inlet of outdoor and indoor units is unblocked OPTIMAL OPERATION Pay attention to the following aspects to ensure an optimal operation Refer to relevant section for details e Adjust air flow direction for avoiding blowing directly to the people in the room e Set the temperature properly to obtain a comfort ambient Too low temperature is not recommended e Please shelter from direct sunlight with curtain or window shutter during cool2. ASSIST FUNCTION Button FAN SPEED Button ADJUSTING Button MODE Button ADJUSTING Button ON OFF Button ON OFF button Operations starts when this button is pressed and stops when you press the button again MODE button Selects the appropriate operating mode from following five modes Auto Automatically set the operation mode Temperature range 17 C 30 C Cool Permits cooling operation Temperature range 17 C 30 C Dry Permits dehumidifying the room air and keep the indoor temperature balanced Temperature range 17 C 30 C Heat Permits heating operation For cooling amp heating models only Temperature range 17 C 30 C Fan Permits fan operation without cooling or heating ASSIST FUNCTION button Use this button to initiate or cancel the assist function 1 Press this button to initiate assist function setting the SWING indicator will flash and seven assist functions can be selected by pressing w button Press the ASSIST FUNCTION button again to select or cancel the relative function Different MODELS have different assist functions SWING gt ECONOMIC RUNNING gt ELECTRICAL HEATING gt TIMER ON gt OFF Note Cooling only or Cooling amp Heating models without ELECTRICAL HEATING feature 2 Relative indicator flashes under the different mode settings 3 The present assist function setting can be confirmed or the selected assist function can be canceled b
3. and pull it upward 3 The air inlet grille can be washed by water or wipe with a dry cloth then dry it in a cool place 4 Use a vacuum cleaner to remove the dust or wash the air filter and dry it in the shadow 5 Installation process of the air filter and air inlet grille is the reverse of the removal process CAUTION Make sure nothing has been forgotten or fallen into the fan before installing the air inlet grille Restart the unit after the air inlet grille is correctly installed MAINTENANCE Before long time idleness 1 Clean the indoor unit and air filter 2 Dry the inner parts by keeping the fan running for half a day 3 Turn off the unit and switch off the power switch remove the batteries from the remote control 4 Periodically check and clean the inner parts of the outdoor unit Our local dealer will help you handle this if you contact us After long time idleness Before restarting please check if the air inlet and air outlet of the indoor and outdoor units are blocked up Clean it so AFTERSALES If the air conditioner operate abnormally turn off the unit and switch off the power and contact the local dealer or service center 10 CS282 U 2200019460
4. button the display shows AUTO COOL gt DRY HEAT FAN AUTO in turn 3 If COOL HEAT or FAN is selected you may press the FAN SPEED button to adjust the indoor fan speed Keep on pressing the button the fan speed will be setas AUTO gt LOW HIGH AUTO in turn But under AUTO and DRY mode the fan speed can not be selected On AUTO operation mode the fan speed is Auto on DRY mode the fan speed is low FAN speed display When operating manually the first fan speed symbol displayed indicates low fan the third symbol displayed indicates high fan three symbols displayed simultaneously indicate Auto fan After finishing the settings it displays sequences as First fan speed symbol Second fan speed symbol Third fan speed symbol When operating with remote controller low frequency displaying cycle of three symbols indicates low fan or Auto fan high frequency displaying cycle of the symbols indicates high fan or Auto fan 4 When in DRY COOL HEAT or AUTO mode adjust the temperature by pressing the A and V button Each depress of the button the temperature would increase decrease 1 C 5 Press the ON OFF button to turn off the air conditioner Please do not stop the unit by pulling out the power plug or switching off the power supply 6 When the unit is on press the ASSIST FUNCTION button the function displayed as SWING ECONOMIC RUNNING ELECTRICAL HEATING gt TIMER ON gt TIMER OFF by pres
5. USER S MANUAL UNITARY TYPE AND FLOOR STANDING SPLIT TYPE We sincerely thank you for purchasing our product Please carefully read this User s Manual before using your air conditioner Save this manual in a safe place for future reference ATTENTIONS rer 1 AIR CONDITIONER OPERATION CONDITIONS 1 CHECK UP BEFORE OPERATION siarp aduee A E E 1 OPTIMAL OPERATION N ANEA NES 1 CAUTION a chained shies catecaabeceataacdeessebadeessa cubed cacestesdpsocedtesnetedeecins cn nteneteastedy cesses 1 DANGER 2 PARTS NAMES EE 2 CONTROL PANEL MANUAL 5 GENERAL OPERATION inio ni jiran eataa aei Sa 5 TIMER SETTINGS 5 ADJUSTING THEAIRFLOW DIRECTION nesenxeresgnwneanenomeny 6 TROUBLESHOOTING e a 7 PHENOMENA NOT CONCERNING MALFUNCTIONS
6. e AUTO TIMER OFF program the TIMER OFF indicator remains on 3 The time will appear in the display window using the select the desired AUTO OFF time press the ASSIST FUNCTION button again to register the time The unit will stop automatically when the specified AUTO OFF time is achieved Cancel the TIMER settings To cancel the auto timed program press the ASSIST FUNCTION button then using the A and button to select the specified AUTO ON OFF time press the ASSIST FUNCTION button again to cancel it Note When the unit is turned to off position non operationsl before setting the AUTO OFF timer the AUTO ON time must be set operational When the unit is turned on before setting the AUTO ON timer the AUTO OFF time must be set operational ADJUSTING THE AIRFLOW DIRECTION Horizontal Airflow AUTO Horizontal Airflow may be adjusted by moving the vertical louvers left and right Press the ASSIST FUNCTION button on the control panel to select the SWING feature to make the louvers move repeat the operation again to stop Note Do not touch the vertical louvers with hand Vertical Ai flow MANUAL Vertical Airflow may be adjusted by horizontal louvers Hold the edge of a vertical louver and move it up and down to adjust vertical air flow Note The starting angle of the horizontal louver should not be too small or the narrow air outlet will affect cooling or heating Do not move the vertical lo
7. e following three situations Just start heating operation Defrosting Heating a low temperature Defrosting For cooling and heating models only Frost may be generated on Outdoor Heat Exchanger when outdoor temperature is low and humidity is high It would lower heating efficiency of the conditioner The air conditioner would stop heating operation and start defrosting automatically After finishing the defrosting it will restart heating operation The fans in both of the indoor and outdoor units will stop running during defrosting operation the time of defrosting is different according to the outdoor temperature and frost degree For approximately 4 10 minutes During defrosting white smog may be come out from outdoor unit This is caused by quickly frosted and it s normal operation 2 White smog discharged from indoor unit When running on cooling mode at a place with high humidity white smog may come into being because of high humidity and high difference in temperature When the air conditioner finish the defrosting it will automatically turn to heating operation the water produced during defrosting will change into snog and come out from indoor unit 3 Low noise of air conditioner When the compressor operating or just stopping there may be some ss sound caused by the refrigerant flowing between indoor and outdoor unit After air conditioner starting or stopping for a short while there may be some zz sound cau
8. ing operation e Please close door and window to avoid the formation of convection that may decrease cooling or heating effect e Please use your remote controller to set the desired run time e Do not put anything near the inlet or outlet to block the airflow Otherwise it may decrease the effect of air conditioner even stop it e Please clean air filter regularly An air logged air filter may affect cooling or heating effect CAUTION e Set the main power switch at some place untouched by young one In rainy day please cut off power supply to avoid damage caused by lightning the unit is left unused for long time or nobody is the conditioned room please turn off the main power supply to avoid accident e Please turn off the main power supply to avoid accident before cleaning or maintaining the unit Do not use cleaning agent liquefacient or corrosive cleanser to clean the unit or spray water other liquid at unit all these may damage plastic components even cause electric shock Do insert your hands stick into the outlet of indoor and outdoor units Otherwise the high speed fan may cause serious injury Do not touch the batten during the louver is rotating Otherwise it may clamp your fingers or cause damage to the gearing of louver Do not attempt to take down the cover of outdoor unit fan to avoid likely injury to you Do not let kids play the units to avoid likely injury e Do not wet indoor u
9. nit and remote controller Otherwise it may cause short circuit or fire e Do not use or restore flammable gas or liquid such as fixture paint gasoline etc near the air conditioner to avoid likely fire If any abnormal symptom such as exceptional noise odor smog abnormal temperature rise of electric leakage etc occurs turn off the power immediately and contact local dealer Do not attempt to repair it by yourself PARTS NAMES This unit consists of indoor unit and outdoor unit Indoor Unit a Vertical Louver Outdoor unit Air Outle Control N Horizontal Louver 9 SSS SSS LSS Refrigerant Pipe Air Inlet SSS _ Sasa SSS Outdoor Power Cord Drain pip NOTE The above air conditioner s outer shape is based on the standard model so it may be different from the one you purchased Air Outlet Let the conditioned air go out from it Control Panel LCD Consists of indicators and control buttons Air Inlet Where a filter is settled absorbing the air in the room and clean it Drain Pipe From which the condensed water is drained Refrigerant Pipe In which the refrigerant passes through connects the outdoor unit with the indoor unit CONTROL PANEL Control Buttons and Functions LCD Signal Receiving Window TEST RUNNING Button LOCK Button TRO a re mnnn Sage lhe a sm
10. o do 1 E1 E2 Temperature Sensor is off or Contact service people E4 short circuit 2 E6 Outdoor unit protection Contact service people 3 E8 Electrostatic dust collection Contact service people The temperature of the evaporator Turn off the unit clean the air filter 4 P4 of indoor unit is too low or high For then restart the unit If this operation the protection feature the does not work please contact service compressor turns off automatically people mng temperature of condenser o Turn off the unit check if there is any the outdoor unit is too high For the gt 5 P5 obstacle in air inlet otherwise call protection feature the compressor peoble turns off automatically PEERS The unit will auto restart after finishing Defrosting protection or warm air 6 9 the defrosting or the temperature of the controlling is off Heat Exchanger of indoor unit raise CAUTION When the power cord is to be replaced replacement work shall be performed by authorized personnel only PHENOMENA NOT CONCERNING MALFUNCTIONS The following symbols do not mean the unit is abnormal 1 Compressor protection Feature Protection for compressor The compressor can not operate within 3 minutes Warm air control For cooling and heating models only Under the HEAT mode the indoor fan speed is automatically reduced or stopped to prevent a cold draft if the set temperature has not been reached under th
11. right picture There is a big difference in temperature Low between indoor and outdoor and this will increase the heating High Low load In this case You are recommended to use another heating Outdoor temperature apparatus in combination with the air conditioner MAINTENANCE AND CLEANING CAUTION For your safety please turn off the unit and shut down the main power switch before cleaning 1 Use a dry cloth to wipe the indoor unit and remote controller 2 A cloth dampened with cold water may be used on the indoor unit if it is very dirty 3 Do not splash water on unit This may cause damage to the inner parts or an electric shock CAUTION 1 Do not use a chemical treated duster for wiping or leave such material on the unit for long 2 Do not use benzine thinner polishing powder or similar solvents for cleaning These may cause the plastic surface to crack or deform Air inlet grille and air filter cleaning The air filter should be checked and cleaned at least once every 2 weeks to maintain optimal performance of the air conditioner Air Filter Air Filter d Note Screw 5 Anti formol filter fixed on the Air filter does not need replacement just wash it with water and dry it in the shadow Air in grid 1 Unscrew the air inlet grille on both sides hold both sides of the grille and pull it up then pull out the grille 2 Take hold of the air filter holder
12. sed by natural expansion or shrindage of plastic parts because of the temperature change 4 Dust blowing from indoor unit e After being left unused for long time the dust may blow out from indoor unit if it is operated again 5 Odor from indoor unit The indoor unit absorbs odor of room furniture or cigarette and emanates them during operation 6 Cooling and Heating mode turned to Fan mode Cooling only models without heating If the indoor temperature achieves to set one the air conditioner controller will stop compressor from running automatically and convert to Fan mode When the temperature increases or decreases to a certain value the compressor will restart and the unit will get right 7 When cooling under high humidity condition relative humidity gt 80 condensate may occur on the surface of indoor unit Please set the louver at the position with Max air flow normal to vertical direction and select High fan speed 8 Lightning car or mobile telephone may cause malfunction of the air conditioner Please unplug your unit for several seconds then connect it again and restart it 9 Heating capacity For cooling and heating models only In heating operation heat is absorbed from outdoor and Heating capacity released into the room That is so called heat pump system High When the outdoor temperature is too low heat absorbed from outdoor reduced and will result in reduced heating capacity see the
13. sing the A and V button press the ASSIST FUNCTION button again to confirm the appropriate mode Note When the unit stays waiting press the ASSIST FUNCTION button only TIMER ON and TIMER OFF feature can be activated When restart the unit after unplug it from the power supply the assist function must be reset if only turn off the unit without shutting off the power SWING feature can be restored in memory Note The program time is not accurate to your local time please reset it Setting the AUTO ON TIMER 1 When the unit is turned to the off position non operational to set the AUTO ON timer press the ASSIST FUNCTION button using the V button to initiate the TIMER ON feature the TIMER ON indicator will flash Press the ASSIST FUNCTION button again to register the AUTO TIMER ON program the TIMER ON indicator remains on 2 The time will appear the display window press the A V button to select the desired AUTO ON time press the ASSIST FUNCTION button again to register the time The unit will start automatically when the specified AUTO ON time is achieved and operate under the former operational mode Setting the AUTO OFF TIMER 1 Press the ON OFF button to turn on the unit 2 To set the AUTO OFF timer press the ASSIST FUNCTION button using A and V button to initiate the TIMER OFF feature the TIMER OFF indicator will flash press the ASSIST FUNCTION button again to register th
14. troller operation is available Push this button again to cancel the LOCK mode LCD B A Indoor fan speed indicator MER B Temperature setting timer setting and maintenance or malfunction information indicator a Timer indicator 7 1 D Lock indicator auto 3 ee BM E Assist function indicator F Mode indicator Meanings of symbols are as shown below 1 Modes Select appropriate operation mode see Manual operation for details Auto AUTO COOLING 7 5 HEATING 2 Assist functions Manual operation for details KN SWING Equally big airflow ECONOMIC RUNNING Save energy ELECTRICAL HEATING Auxiliary electric heater rending rapid heating up even in cold winter Only for the cooling amp heating type with Electric heater 3 Others First Fan Speed Symbol The low frequency flashing cycle of the three Second Fan Speed Symbol fan speed symbols indicate low fan or Auto fan The high frequency flashing cycle of the fan Third Fan Speed Symbol speed symbols indicate high fan or Auto fan GENERAL OPERATION When the air conditioner has been connected with the power supply follow the procedures given below to operate your air conditioner 1 Press ON OFF button to start the unit 2 Press MODE button to select a desired mode Keep on pressing the
15. uver manually or it may malfunction during operation Do not set the starting angle of the louvers too small during cooling or drying operation Otherwise condensation may occur on the surface of the horizontal louver and cause dew dripping TROUBLESHOOTING Before calling for service please review the following list of common problems and solutions Problem Possible Cause Solutions Air conditioner does not operate at all Power failure Wait for power restoring The power supply is disconnected Switch on the main power switch The power fuse is blown Change the fuse The timer is set Wait or cancel timer setting The batteries of the remote control are exhausted Change the batteries Air conditioner does not cool or heat well The temperature setting is too high or too low Set a more comfortable temperature The air filter is clogged with dust Clean the filter The air inlet or outlet of the outdoor unit is blocked Clear up the block Doors or windows are open Close the doors or windows Air conditioner does not cool or heat at all The air inlet or outlet of the outdoor unit is blocked Clear up the block first then begin to operate Three minute protection feature Wait for a while Unappropriated temperature setting Set the temperature properly Number ais Problems What t
16. y the second depression of the button then it automatically enters the next assist function setting operation 4 Assist function setting program automatically cancel when nothing has done to the ASSIST FUNCTION button button within 10seconds If any other button is pressed during this period it will override the assist function setting program immediately FAN SPEED button This button is used to select the desired fan speed Each time you push the button a fan speed is selected in a sequence as following AUTO gt LOW gt meh ADJUSTING button 1 Temperature adjust Press A and WV to adjust the temperature except under Assist Function Timer or Checking setting mode 2 Timer adjust Adjust the timer on off time under the Timer setting mode 3 Assist function selection Select the desired assist function by pressing and Y 4 Under the Checking mode press A Y to check T1 2 protection code and malfunction code TEST RUNNING button This button is specially designed for maintenance technicians Press this button will enter force cooling operation press it again to close the test running If malfunctions occur during test running or air condition operating press ADJUSTING button to display the maintenance information LOCK button When you press the LOCK button the first time all the current settings are locked in but the remote con
Download Pdf Manuals
Related Search