OP Series HDD Duplicator User`s Manual
Contents
1. The password must be 6 characters Setup Boot Password Boot Password 10 Boot Password m Enable Use Aor Y to select Use Aor Y to select Press ENT to confirm 6 11 Setup Password This option allows to set up password for Setup function to prevent from the change of system settings on the duplicator The password must be 6 characters Setup Setup Password Setup Password 11 Setup Password Enable Use Aor Y to select Use Aor Y to select Press ENT to confirm 6 12 Language This option allows to choose the language for display English Spanish Portuguese and Japanese English is the default language Setup Language 12 Language English Use Aor Y to select 6 13 Clear Setup This option resets the duplicator back to factory default settings Setup Clear Parameter To Default Clear Parameter To Default 13 Clear Setup Yes All Parameters were cleared Use Aor Y to select 14 6 14 Performance This option allows to set up the performance for Copy function based on the following modes Speed Balance and Compatibility Speed mode is to execute the Copy function at the fastest speed but may have compatibility issue with certain brands flash media Balance mode is to execute the Copy function at stable speed and have less compatibility issue with certain brands flash media Compatibility mode is to execute the Copy function at the most stable speed and almost have no compatible issue2. 4 Capacity Check Check 8 Result Ready device 8 Pass 8 Fail 0 Source and target devices inserted Display progress status Final result 5 Utility 5 1 Format FAT32 This option allows to format the target device to FAT32 file format It will not format the source device avoiding accidently erasing the original data content User will be asked if it is sure to format the target devices before the Format process starts Utility Sure to format Format 7 1 Format FAT32 NT Yes P OF 0 0 Use Aor Y to select option Display progress status Result Pass 7 Fail 0 Final result 5 2 Format exFAT This option allows to format the target device to exFAT file format It will not format the source device avoiding accidently erasing the original data content User will be asked if it is sure to format the target devices before the Format process starts Utility Sure to format Format 7 1 Format exFAT o Yes P 0F 0 0 Use Aor Y to select option Display progress status Result m Pass 7 Fail 0 Final result 5 3 Measure Speed This option allows to measure the actual Read and Write speed of the target device This option will NOT alter or erase existing data on the target device Utility 0 Read 20M 1 Read 3 Measure Speed ENT 1sec Write 16 5M mad 1sec Write Display read write speed Use Aor Y to select device 5 4 Quick Erase This option erases the table of content
3. after execution of this function Utility D Signatures 0 Result 7 Change Disk Signatures eyr P O F 0 Wait ENT Pass 7 Fail 0 Display progress status Final result 5 8 Media Information This option displays the information of selected HDD device such as total capacity file format and the size of data content Utility Port Total Capacity 8 Media Information File Format Data Size Use Aor Y to select device 5 9 Device Model This option displays the model information of selected HDD device such as device model serial information and firmware version Utility 0 P 0 1 P 1 9 Device Model NT Model information Model information Use Aor Y to select device 5 10 System Information This option displays general information of the duplicator including controller model system memory size firmware version and number of targets 10 Utility H0104S 128MB Controller Model Memory 10 System Info ayy V1 05 12 1 4 H Firmware Target Number Display system information 5 11 System Update This option allows user to update the firmware of duplicator when necessary Please obtain the proper firmware file from manufacturer and save the unzipped file under home folder on the flash device DO NOT save the file under sub folder Insert the flash device containing the firmware into the source port of duplicator and press ENT It will update the system reboot the duplicator after update activ
4. i 2 5G data to be copied l l P number of passed copies l l l l l l F number of failed copies Basic Mode l 10 rate of progress l 1 Copy 1 number of target l 2 5G data to be copied I 1 03 45 copy time used 10 rate of progress 1 I I Show Timer Mode A 10 number of targets in copy process P 0 number of targets passed copy 4 2303M the port with highest copy speed and data copied so far 1 2183M the port with lowest copy speed and data copied so far 4 2303M 1 2183M Expert Mode 6 7 Start up Menu Choose one of the following as the default start up function Copy Compare Copy Compare Capacity Check Utility and Setup The default start up function is Copy Setup Start up Menu 7 Start up Menu Ss Copy Use Aor Y to select 6 8 Button Beep This option allows to set up button sound from the following options Button amp Warning OFF Warning only The default setting is Button amp Warning Setup Button Beep 8 Button Beep Button amp Warning Use Aor Y to select 6 9 Show Result Time This option allows to enable or disable the display of copy time after finishing the 13 copy process The default setting is disable Setup Show Result Time 9 Show Result Time Disable Use Aor Y to select 6 10 Boot Password This option allows to set up password for system boot up to prevent from the unauthorized use of the duplicator
5. of file system of the target device so it is fast to do Quick Erase There is chance that some files can be retrieved by software Utility Sure to erase Q Erase 7 4 Quick Erase NT Yes P 0 F 0 0 Use Aor Y to select option Display progress status Result Pass 7 Fail 0 Final result 5 5 Full Erase This option completely erases the content of target device It takes longer time to erase and the content will not be retrieved by software Utility Sure to erase F_Erase 7 5 Full Erase Yes NT P 0 F 0 0 Use Aor Y to select option Display progress status Result Pass 7 Fail 0 Final result 5 6 DoD Erase This is to comply with the U S A Department of Defense DoD 5220 standard to fully erase the HDD by rewriting bit by bit three times to guarantee the data to 9 be permanently deleted It takes the longest time to erase and the content will not be retrieved by software Utility Sure to erase DoD Erase 7 6 DoD Erase Yes ENT P OF O 0 Use Aor Y to select option Display progress status Result Pass 7 Fail 0 Final result 5 7 Change Disk Signatures Duplicator generates the same disk signatures after copy which may cause computer unable to read the disk correctly when two disks with identical disk signatures are presented or shut down the computer This function allows to change disk signature Attention it will cause error data mismatch if compare the disks
6. set up the display of time g Don t need to wait for all target devices to be done Each channel executes the task asynchronously IV Menu Overview 1 Copy To copy from source HDD to target HDD s please go to 6 1 Copy Area to select the setting first before this step 1 Copy 1 Copy Copy 7 7 8G Source Not Ready Ready device 7 i P OF 0 10 No source device Source and target devices inserted Display copy progress ENEE ES 2 Copy 7 number of targets 7 8G data to be copied Result l I Pass 7 Fail 0 P number of passed I I I F number of failed 10 rate of progress Final result The process of all tasks are displayed in the same format 2 Compare This command allows to compare the copied target HDD devices against the source for accuracy 2 Compare COMP 7 7 8G Result Ready device 7 P OF 0 80 Pass B Fail 1 Source and target devices inserted Display compare progress Final result 3 Copy Compare This command allows duplicator to start Copy process first then follow with Compare process immediately 3 Copy Compare Copy amp 7 7 8G amp COMP 7 7 8G Ready device 7 N P OF 0 10 P OF 0 10 Source and target devices inserted Display copy progress Display compare progress Result Pass 6 Fail 1 Final result 4 Capacity Check This command allows to verify the HDD device capacity It can detect the actual capacity of devices within 3 seconds
7. Auto Control system starts and stops fan running automatically according to the process of task With over voltage protection the duplicator system shuts down power supply automatically to protect hard disk drive from damage when the power supply is unstable 2 Control Panel Overview 2 line backlit LCD A Button ENT Button ESC Button Y Button A Button Up Backward ENT Button Enter OK Y Button Down Forward ESC Button Escape Cancel 3 Specifications Product specs may change without notice Operation Standalone No PC or software is required Supported HDD 2 5 and 3 5 SATA HDD SATA Il Ill and SSD Display 2 line Backlit Monochrome LCD Power Supply 115V or 230V Control Button 4 push button control panel ENT ESC UP DOWN Working 20 80 Humidity Storage 5 95 Working 32 F 167 F Temperature Storage 4 F 185 F Il Warning 1 The duplicator tasks mentioned in this user s manual are as following Copy Compare Copy Compare Capacity Check and the functions under Utility sub menu such as Format FAT32 Format exFAT Quick Erase Full Erase and DOD Erase 2 The Green LED flashes during the execution process of a task After the task is done the Green LED will stay solid if the process is successful otherwise the Red LED will be on if the process is failed 3 Press and hold ESC button during the execution process of a task will stop and ex
8. OP Series HDD Duplicator User s Manual Version 7 0 All rights reserved 2015 Table of Contents l Introduction 1 Features 2 Control Panel Overview 3 Specifications ll Warning lll Synchronous Asynchronous Mode 1 Synchronous Mode 2 Asynchronous Mode IV Menu Overview 1 Copy 2 Compare 3 Copy Compare 4 Capacity Check 5 Utility 5 1 Format FAT32 5 2 Format exFAT 5 3 Measure Speed 5 4 Quick Erase 5 5 Full Erase 5 6 DOD Erase 5 7 Change Disk Signatures 5 8 Media Information 5 9 Device Model 5 10 System Information 5 11 System Update 6 Setup 6 1 Copy Area 6 2 Asynchronous Mode 6 3 Smaller Target 6 4 Unknown Format 2 un AA A LB LO OO OO OO O O O Oo N N N N D QAQA P e e e he RP BP Pe BP P N N N e be e O O O O 6 5 6 6 6 7 6 8 6 9 6 10 6 11 6 12 6 13 6 14 Check Before Copy Display Mode Start up Menu Button Beep Show Result Time Boot Password Setup Password Language Clear Setup Performance 12 12 13 13 13 14 14 14 14 15 I Introduction This duplicator system is designed and developed based on the FPGA from the world famous semiconductor company XILINX Every processing channel is parallel to each other with its own control unit therefore the duplicator will not sacrifice speed for the increasing number of targets loaded always remain the same and fast copy speed The duplicator supports fast copy with multiple file formats created by three major operating systems Windows Lin
9. e and operate under the new firmware Utility Update BIOS Update BIOS 11 System Update l Identify disc ENT Complete Reboot Looking for firmware 6 Setup 6 1 Copy Area This option allows to select the area on the source device to copy onto the target devices You may select either System And Files to skip all the unoccupied area on the source device or Whole Media By default the copy area is set up as System And Files 6 1 1 System And Files The duplicator first analyzes the file format of source HDD device You may copy only the system and files area to save overall copy time if the file format is FAT16 FAT32 exFAT NTFS Windows EXT2 EXT3 EXT4 Linux and HFS HFS Mac Otherwise the duplicator will copy the entire source device content to the target devices including unoccupied space For instance the source HDD has 2TB capacity but with only 50MB of data in FAT32 file format The duplicator will copy only the 50MB of data area to the target HDD s hence shortening overall copy time 6 1 2 Whole Media When selected the duplicator copies the entire content on the source HDD device including both the data and empty spaces This option is used when you have a source device with unknown file format For instance a source HDD has 2TB capacity and 50MB of data with unknown file format the duplicator will copy the whole 2TB of content to target HDD s 11 6 2 Asynchronous Mode This option all
10. e duplicator will read the data from source device into system memory buffer and start to execute a task immediately when target device s inserted Duplicator does not have to wait for all target device s inserted in order to start the execution of the task at the same time No matter the data size of the source device duplicator can asynchronously execute a task if Asynchronous Mode is enabled Go to 6 2 Asynchronous Mode to enable or disable this function a Insert source media into the source channel select the task to execute from the menu and press ENT button Duplicator will start to execute the task now b Target devices can be plugged in during the execution process and will start to execute the task immediately 6 c Target device can be removed when it finishes the execution process and its green LED is solid on New target device can be plugged into the same channel for execution of the task again d LCD display will show the percentage of execution process the number of successful and failed target s Here the percentage of execution process displayed is only for the least processed target device e During the execution process the status of each target device can be checked by using the A and Y buttons f After the task is done for all target devices press ESC button to exit from the task LCD display will show the total number of successful and failed target s and total execution time Go to 6 9 Show Result Time to
11. it the execution of the task 4 DO NOT unplug HDD from the duplicator during the execution process of a task It may cause damage to the duplicator system and HDD 5 It is strongly recommended that the capacities of the source and target HDD are equal or similar lll Synchronous Asynchronous Mode 1 Synchronous Mode Default Synchronous Mode means that the duplicator will start to execute a task after the source and target devices have been inserted and the ENT button is pressed The task will begin and end at the same time for all target devices Any other target device plugged in during the process of a task will not be executed with the task Go to section 6 2 Asynchronous Mode to enable or disable this function a Insert source media into the source channel and blank media into the target channels properly The LCD display will show no source disk when source media is not plugged in yet and show the number of target media inserted when source media plugged in b The green LED will be on if the target device is plugged in properly c Select the task from menu and press ENT button to execute it d During the execution process the status of each target device can be checked by using the A and Y buttons e After the task is done LCD display will show the number of successful and failed target s and execution time Go to section 6 9 Show Result Time to set up the display of time 2 Asynchronous Mode Asynchronous Mode means that th
12. ows to enable or disable Asynchronous Mode By default the Asynchronous Mode is disabled Please refer to Chapter III for the detail of operation on Synchronous and Asynchronous Mode Setup Asynchronous Mode 2 Asynchronous Mode Disable Use Aor Y to select 6 3 Smaller Target If the capacity of the target HDD is smaller than the source HDD the duplicator will partly copy or cannot copy Cannot Copy is the default setting Setup Smaller Target 3 Smaller Target Es Cannot Copy Use Aor Y to select 6 4 Unknown Format This option allows you to Copy or Skip unknown format If option Skip is selected here the unknown format from source will not be copied during copy process Copy unknown format is the default setting Setup Unknown Format 4 Unknown Format Swa Copy Use Aor Y to select 6 5 Check Before Copy This option allows to check device real capacity before copying By default this option is disabled Setup Check Before Copy 5 Check Before Copy Disable Use Aor Y to select 6 6 Display Mode There are three display modes Basic Show Timer and Expert Basic Mode shows the copy progress in general Show Timer Mode displays the time used for the task Expert Mode shows the devices with highest copy speed and lowest copy speed and their copy progress respectively By default it is Basic Mode 12 Setup Display Mode 6 Display Mode aid Basic l Copy 1 number of target
13. ux MAC and makes mirror copies of data efficiently GPT and MBR partition formats and 4K advanced format hard disk drive HDD are all supported Furthermore this duplicator has been fully tested with quality assurance before leaving our manufacturing facility 1 a w 0 Features Each processing channel has its own control unit and operates independently with dedicated bandwidth of up to 150 MB s Standalone operation No PC or software is required minimizing possible computer virus infection Instant power on and off no warm up or cool down required Easy to use One Touch copy operation Compare function available for verification of copy accuracy Menu options are user friendly and easily accessed through the 4 button control panel Use Aor Y button to scroll through the options and view the operation status of each channel on the 2 line backlit LCD display All functions support synchronous and asynchronous mode to achieve higher efficiency Powerful 32 bit CRC checksum to assure data integrity Heavy duty hardware construction for commercial production or personal use 115V and 230V switching power supply maximizes portability for operation anywhere Designed to save users time and effort in creating multiple copies quickly and reliably Unique source data analysis to copy data area only to achieve highest efficiency Supports multiple file formats Windows FAT 16 32 exFAT NTFS Linux Ext 2 3 4 Mac HFS HFS Fan
14. with flash media The default mode is Speed Setup Performance 14 Performance Speed Use Aor Y to select Version 7 0 Allrights reserved 2015 15
Download Pdf Manuals
Related Search