FCC 47 CFR PART 15 SUBPART B TEST REPORT
Contents
1. Compliance Certification Services Inc FCC 47 CFR PART 15 SUBPART B TEST REPORT for Digital Satellite Receiver MODEL DBS7000 Brand LEXIUM Test Report Number T110118401 D Issued to WS International 1200 Cobb Parkway North Suite 100B Marietta Georgia 30062 USA Issued by Compliance Certification Services Inc Tainan BU No 8 Jiu Cheng Ling Jiaokeng Village Sinhua Township Tainan Hsien 712 Taiwan R O C TEL 886 6 5802201 FAX 886 6 5802202 Issued Date January 27 2011 NAVAS S SS Gar S i at Jac MRA o Testing Laboratory f yw 1109 Note This report shall not be reproduced except in full without the written approval of Compliance Certification Services Inc This document may be altered or revised by Compliance Certification Services Inc personnel only and shall be noted in the revision section of the document The client should not use it to claim product endorsement by TAF NIST or any government agencies The test results in the report only apply to the tested sample Page 1 24 Compliance Certification Services Inc M28 Revision History Issue Effect al Date Revisions crm Revised By January 27 2011 Initial Issue Initial Issue Issue ALL Sunny Chang Page 2 This report shall not be reproduced except in full without the written approval of Compliance Certification Services 1 2 3 3 1 DECISION OF FINAL TEST MODE ici2. 0 01 25 52 34 18 60 02 1 25 84 QP 0 308 8 65 0 01 9 88 18 54 50 02 1 31 48 AVERAGE 3 074 8 66 0 02 17 75 26 43 56 00 1 29 57 QP 3 074 8 66 0 02 11 07 19 75 46 00 1 26 25 AVERAGE 8 020 8 89 0 02 8 14 17 05 50 00 1 32 95 AVERAGE 8 020 8 89 0 02 14 71 23 62 60 00 1 36 38 QP 16 661 8 78 0 15 1 13 35 22 28 50 00 1 27 72 AVERAGE 16 661 8 78 0 15 1 25 21 34 14 60 00 1 25 86 QP NOTE 1 Measured Level dBuV LISN Factor dB Cable Loss dB Meter Reading dBuV 2 Over Limit dBuV Measured Level dBuV Limits dBuV Page 14 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc 7 RADIATED EMISSION MEASUREMENT 7 1 LIMITS OF RADIATED EMISSION MEASUREMENT Below 1GHz for digital device dBuV m At 10m Class A Class B 30 230 40 30 230 1000 47 37 FREQUENCY MHz Limit tables for non digital device Class A Radiated Emission limit at 10m Hr others MHZ P 30 88 88 216 960 Above 960 Class B Radiated Emission limit at 3m Mes others MHZ uV m Q P ay P Above 1GHz for all device Frequency Class A dBuV m At 10m Class B dBuV m At 3m MHZ Average Peak Average Peak Above 1000 NOTE 1 The lower li
3. s loss LISN to EMI Tester Receiver Meter Reading Uncorrected Analyzer Receiver reading Measured Level Meter Reading LISN Factor Cable loss Limit Limit stated in standard Over Limit Measured Level Limits Detector Peak PK Peak Reading QP Quasi peak Reading AV Average Reading Calculation Formula 1 Measured Level dBuV LISN Factor dB Cable Loss dB Meter Reading dBuV 2 Over Limit dBuV Measured Level dBuV Limits dBuV Page 12 This report shall not be reproduced except in full without the written approval of Compliance Certification Services O Compliance Certification Services Inc ee ee 6 6 TEST RESULTS Model No DBS7000 6dB Bandwidth Environmental Environmental E 55 Test Mode Normal Operation Tested by Shiang Su Line The chart below shows the highest readings taken from the final data Data 1 0 Level dBuV Date 2011 01 21 40 0 15 0 5 1 2 5 10 20 30 Trace Discrete Frequency MHz Freg LISN Cable Meter Measured Limits Over Factorl Loss Reading Level Limits lDetector MHz dB dB dBuV dBuV dBuV 0 184 8 65 0 01 39 51 48 17 64 28 1 16 12 QP 0 184 8 65 0 01 23 29 31 95 54 28 1 22 34 AVERAGE 0 248 8 65 0 01 31 78 40 45 61 82 1 21 37 QP 0 248 8 65 0 01 14 45 23 11 51 82 1 28 71 AVERAGE 0 305 8 65 0 01 25 36 34 02 60 10 1 26 08 QP 0 3
4. 120VAC 60Hz power source from the outlet socket under the turntable All support equipment power received from another socket under the turntable The antenna was placed at 3 or 10 meter away from the EUT as stated in ANSI C63 4 The antenna connected to the Spectrum Analyzer via a cable and at times a pre amplifier would be used The Analyzer Receiver quickly scanned from 30MHz to 40GHz The EUT test program was started Emissions were scanned and measured rotating the EUT to 360 degrees and positioning the antenna 1 to 4 meters above the ground plane in both the vertical and the horizontal polarization to maximize the emission reading level The test mode s described in Item 3 1 were scanned during the preliminary test After the preliminary scan we found the test mode described in Item 3 1 producing the highest emission level The worst configuration of EUT and cable of the above highest emission level were recorded for reference of the final test Page 18 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Procedure of Final Test EUT and support equipment were set up on the turntable as per the configuration with highest emission level in the preliminary test e The Analyzer Receiver scanned from 30MHz to 40GHz Emissions were scanned and measured rotating the EUT to 360 degrees varying cable placem
5. QP Quasi peak Reading AV Average Reading Calculation Formula Over limit dBuV m Result dBuV m Limit dBuV m Above 1GHz Freq Reading AF Closs Filter Level Limit Margin Mark Height MHz dBuV dBuV dB dB dB dBuV m dBuV m dB P Q A Meter Digital Satellite 56 00 25 14 2 07 41 77 1072 42 16 70 00 27 84 P 1 00 ReceiverX XX Freq Emission frequency in MHz Reading Uncorrected Analyzer Receiver reading AF Antenna Factor Closs Cable s loss Pre amp Pre amp Gain Filter Insertion loss of filter Level Reading AF Closs Pre amp Filter Limit Limit stated in standard Margin Reading in reference to limit Mark P Peak Reading Q Quasi peak Reading A Average Reading Height Antenna Height Calculation Formula Margin dB Level dBuV m Limit dBuV m Page 20 This report shall not be reproduced except in full without the written approval of Compliance Certification Services O Compliance Certification Services Inc 7 6 TEST RESULTS Below 1GHz Model No DBS7000 Test Mode Normal Operation 6dB Bandwidth 120 kHz Environmental MESSEN Antenna Antenna Pole 26 3deg C 60 RH Report No T101223402 D Detector Function on by LEE GUO The chart below shows the highest readings taken from the final data Data 1 80 Level dBuV m 40 Date 2011 01
6. 05 8 65 0 01 6 29 14 95 50 10 1 35 15 AVERAGE 2 993 8 66 0 02 17 61 26 29 56 00 1 29 71 QP 2 993 8 66 0 02 13 91 22 59 46 00 1 23 41 AVERAGE 7 728 8 88 0 02 13 07 21 97 60 00 1 38 03 QP 7 728 8 88 0 02 4 63 13 53 50 00 1 36 47 AVERAGE 16 661 8 78 0 15 25 80 34 73 60 00 1 25 27 OP 16 661 8 78 0 15 15 72 24 65 50 00 1 25 35 AVERAGE NOTE 1 Measured Level dBuV LISN Factor dB Cable Loss dB Meter Reading dBuV 2 Over Limit dBuV Measured Level dBuV Limits dBuV Page 13 This report shall not be reproduced except in full without the written approval of Compliance Certification Services O Compliance Certification Services Inc EE Martini Em ae ate 22deg C 55 RH Test Mode Normal Operation Conditions Neutral The chart below shows the highest readings taken from the final data Data 2 80 Level dBuV Date 2011 01 21 40 0 15 0 5 1 2 5 10 20 30 Trace Discrete Frequency MHz Freg LISN Cable Meter IMeasured Limits Over Factorl Loss Reading Level Limits lDetector MHz dB dB dBuV dBuV dBu dBuV 0 185 8 65 0 01 38 14 46 80 64 24 1 17 44 0 185 8 65 0 01 21 94 30 60 54 24 1 23 64 AVERAGE 0 248 8 65 0 01 14 09 22 75 51 82 1 29 07 AVERAGE 0 248 8 65 0 01 30 56 39 22 61 82 1 22 60 QP 0 308 8 65
7. 25 0 30 224 Trace Discrete Freq Reading Antenna Level Factor MHz dBuv dB m 34 15 14 93 18 49 86 10 18 65 7 90 114 55 13 39 13 32 189 00 12 45 12 43 230 88 8 40 12 41 384 73 11 49 16 05 459 00 11 77 17 46 540 00 10 03 18 79 609 95 12 86 19 43 740 53 3 23 21 22 891 00 2 68 22 71 999 00 1 90 24 00 418 612 Frequency MHz Measure Limit Level dBuV m dBuV m 34 62 40 00 28 15 40 00 29 32 43 50 28 31 43 50 24 65 46 00 32 98 46 00 35 01 46 00 35 12 46 00 39 21 46 00 32 35 46 00 34 22 46 00 35 10 54 00 806 Detector 1000 Note 1 QP Quasi peak Reading 2 The other emission levels were very low against the limit Page 21 This report shall not be reproduced except in full without the written approval of Compliance Certification Services O Compliance Certification Services Inc M Model No No DBS7000 TestMode Mode Normal Operation Normal Operation oat 26 3deg C 60 RH Bandwidth 120 kHz ec E Antenna Pole Pole Horizontal Antenna Distance Distance Hom Detector Function oe RR by EN GUO The chart below shows the highest readings taken from the final data Data 2 80 Level dBuV m Date 2011 01 25 40 0 30 224 418 612 806 1000 Frequency MHz Trace Discrete Freq Reading Antenna Cable Measure Limit Over D
8. ble measurement uncertainty value without requiring revision of the compliance statement is base on conducted and radiated emissions being less than Ucispr which is 3 6dB and 5 2dB respectively CCS values called U_ap in CISPR 16 4 2 is less than Ucispr as shown in the table above Therefore MU need not be considered for compliance Page 9 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Report No T101223402 D 6 CONDUCTED EMISSION MEASUREMENT 6 1 LIMITS OF CONDUCTED EMISSION MEASUREMENT Class A dBuV Class B dBuV FREQUENCY MHz NOTE 1 The lower limit shall apply at the transition frequencies 2 The limit decreases in line with the logarithm of the frequency in the range 0 15 to 0 50 MHz 3 All emanations from a class A B digital device or system including any network of conductors and apparatus connected thereto shall not exceed the level of field strengths specified above 6 2 TEST INSTRUMENTS Conducted Emission room 1 Name of Equipment RON E Serial Number Calibration Due L I S N SCHWARZBECK ETT 8121 8121308 308 MAR MAR 09 2011 2011 TEST RECEIVER Rohde amp Schwarz ESCS 30 100348 JUL 13 2011 BNC COAXIAL CCS BNC50 11 OCT 04 2011 CABLE BNC COAXIAL BNC50 OCT 04 2011 CABLE e 3 5 04211c R amp S 2 27 Test S W NOTE 1 The calibration interval of the abo
9. ci eerte e tb nne iate the a de aa casada 3 2 EUT SYSTEM OPERATION 000 ee ten eee ener 4 4 1 DESCRIPTION OF SUPPORT UNITS 4 2 CONFIGURATION OF SYSTEM UNDER TEST sese nennen nnne sennes 5 912 FACILITIES uiu iet ettet he bien deni erae eun ie c aaa eden VE pe ea uada 5 2 5 3 MEASUREMENT 6 Compliance Certification Services Inc TABLE OF CONTENTS TEST RESULT CERTIFICATION 5 inania nucakakn acu uikkanuuxuu Caii an ru ck au da da a ci ida BUT DESCRIPTIQN ccsinsainiEiniuiic nuni dq RISE IN PULS SEC tU S RUNS SOY UN DM RIVE EI MENGE CC TEST METHODOLOGY scires uve ti aV rr EE DONIS Ee ndn SU FOR SETUP OF EQUIPMENT UNDER TEST iban icu dato kon ihn kan t ko hinh FACILITIES AND ACCREDITATIONS iin sa s nain iaa a taxa saa CER Ea b va dE aS s ERES Ea upRV na nnmnnn CONDUCTED EMISSION 50 6 1 LIMITS OF CONDUCTED EMISSION 0 6 2 TESTINSTRU MENTS itt rette tiere ne Lene en Fh dne tir ee eL d n e 6 3 TEST PROCEDURES tie eit Oa TESLOETUP uuo are e
10. creditation certificates are available for downloading from our web site http www ccsrf com Page 8 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc M 5 3 MEASUREMENT UNCERTAINTY Where relevant the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16 4 2 Measurement Uncertainty Power Line Conducted Emission 9kHz 30MHz 2 01dB Test Site OATS 5 30 MHz 200 MHz 3 57dB 200 MHz 1000 MHz 3 53dB E m Test Site OATS 6 30 MHz 200 MHz 3 40dB 10m 200 MHz 1000 MHz 3 50dB 3 81dB Test Site OATS 7 ssa alle 200 MHz 1000 MHz 3 08dB Test Site OATS 5 30 MHz 200 MHz 3 16dB 200 MHz 1000 MHz 3 04dB C omom oa Test Site OATS 6 30 MHz 200 MHz 3 38dB 200 MHz 1000 MHz 3 04dB Test Site OATS 6 1000 MHz 6000 MHz 3 20dB This uncertainty represents an expanded uncertainty expressed at approximately the 95 confidence level using a coverage factor of k 2 Consistent with industry standard e g CISPR 22 2005 clause 11 Measurement Uncertainty determining compliance with the limits shall be base on the results of the compliance measurement Consequently the measure emissions being less than the maximum allowed emission result in this be a compliant test or passing test The accepta
11. e details please refer to the User s manual of the EUT Page 5 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc M 3 TEST METHODOLOGY 3 1 DECISION OF FINAL TEST MODE The EUT was tested together with the above additional components and a configuration which produced the worst emission levels was selected and recorded in this report The test configuration modes are as the following Conduction Modes Normal Operation Radiation Modes 1 Normal Operation 3 2 EUT SYSTEM OPERATION Setup whole system for test as shown on setup diagram Turn on power and check function Start to test by test mode Note Test program is self repeating throughout the test Page 6 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc 4 SETUP OF EQUIPMENT UNDER TEST 4 1 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units The following support units or accessories were used to form a representative test configuration during the tests Peripherals Devices Product Manufacturer Model No Certify No Signal cable CHI MEI TL 22W6000T R63298 Unshd 1 6m Signal cab
12. e reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc E E 7 2 TEST INSTRUMENTS Open Area Test Site 5 TEST RECEIVER Rohde amp Schwarz ESCS 30 100294 MAR 09 2011 TYPE N COAXIAL SUHNER RG_214_U 2X 5 NOV 24 2011 CABLE Test Software EMI e 3 AUDIX 5 04211c Above 1GHz Used E INSTRUMENT RF Swicth ERS 180A EC1204141 N C R TELH LTD Test Software e 3 5 043036 NOTE 1 The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML ROC and NIST USA 2 N C R No Calibration Request Page 17 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Report No T101223402 D 7 3 TEST PROCEDURES P rocedure of Preliminary Test The equipment was set up as per the test configuration to simulate typical usage per the user s manual When the EUT is a tabletop system a wooden turntable with a height of 0 8 meters is used which is placed on the ground plane When the EUT is a floor standing equipment it is placed on the ground plane which has a 12 mm non conductive covering to insulate the EUT from the ground plane Support equipment if needed was placed as per ANSI C63 4 All I O cables were positioned to simulate typical usage as per ANSI C63 4 The EUT received AC
13. ent and positioning the antenna 1 to 4 meters above the ground plane in both the vertical and the horizontal polarization to maximize the emission reading level e Recording at least the six highest emissions Emission frequency amplitude antenna position polarization and turntable position were recorded into a computer in which correction factors were used to calculate the emission level and compare reading to the applicable limit Below 1GHz the Q P reading and above 1GHz the Peak and Average reading are presented e The test data of the worst case condition s was recorded 7 4 TEST SETUP Test table amp Turntable 1m 4m f Coaxial Cable Power Cable 3 or 10 m PI EMI Receiver For the actual test configuration please refer to the related item Photographs of the Test Configuration Page 19 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc ee ee 7 5 DATA SAMPLE Below 1GHz Reading Antenna Measure imi Over fou level limit Detector dBuV m dBuV m dBuV m Freq Emission frequency in MHz Reading Uncorrected Analyzer Receiver reading Antenna Factor Antenna Factor Amplifier Gain Cable los Cable s loss Measure level Reading Antenna Factor Cable loss Limit Limit stated in standard Over limit Measure level Limit Detector Peak PK Peak Reading
14. et Class B limit ICES 003 Issue 4 ANSI C63 4 2003 Radiated PASS Meet Class B limit Note 1 statements of test result on the above are decided by the request of test standard only the measurement uncertainties are not factored into this compliance determination 2 The information of measurement uncertainty is available upon the customer s request Deviation from Applicable Standard None The above equipment has been tested by Compliance Certification Services Inc and found compliance with the requirements set forth in the technical standards mentioned above The results of testing in this report apply only to the product system which was tested Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties Approved by Reviewed by _ Lov S He Jeter Wu Eric Huang Assistant Manager Assistant Section Manager Page 4 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc 2 EUT DESCRIPTION Report No T101223402 D Product Digital Satellite Receiver Applicant WS International PORT Exmewr z wowor o J ew amp svooo o NA swear o ev Note 1 Client consigns two model samples to test Model Number DBS7000 Therefore the testing Lab just guarantees the unit which has been tested 2 For mor
15. etector Level Factor Loss Level Limt 1 MHz dBuV dB m dB dBu m dBuV m dBuV m 1 86 13 15 32 7 90 1 2 20 25 42 40 00 14 58 QP 112 20 16 60 13 03 2 59 32 21 43 50 11 29 QP 1 185 14 11 89 12 06 3 45 27 40 43 50 16 10 QP 1 270 00 18 81 13 05 1 4 20 36 06 1 46 00 9 94 QP 1 307 73 13 80 14 30 4 59 32 68 46 00 13 32 QP 1 459 00 11 02 17 46 1 5 78 34 26 46 00 11 74 QP 538 75 15 10 18 75 6 28 40 13 46 00 5 87 QP 609 95 12 20 19 43 6 98 38 61 46 00 7 39 QP 813 40 6 70 22 02 8 30 37 01 46 00 8 99 QP 999 48 0 70 24 00 9 20 33 90 54 00 20 10 QP 1 QP Quasi peak Reading 2 The other emission levels were very low against the limit Page 22 This report shall not be reproduced except in full without the written approval of Compliance Certification Services O Compliance Certification Services Inc MM M 8 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST LETT TS Use Im Si E P L I2 gt ZU x i4 4 Mio T e 23 This report shall not be reproduced except full without the written approval of Compliance Certification Services O Compliance Certification Services Inc RADIATED EMISSION TEST Page 24 This report shall not be reproduced e
16. le description Power Cable Unshielded 1 6m 1 pcs RS232 Gable IHDMICable Shielded 1 1m 1 pcs H Coaxial Cable Shielded 1 8m 1 pcs Note 1 All the equipment cables were placed in the worst case configuration to maximize the emission during the test 2 Grounding was established in accordance with the manufacturer s requirements and conditions for the intended use 4 2 CONFIGURATION OF SYSTEM UNDER TEST Satellite Source A AC Source Page 7 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc ee 5 FACILITIES AND ACCREDITATIONS 5 1 FACILITIES All measurement facilities used to collect the measurement data are located at CCS Taiwan Tainan BU at No 8 Jiu Cheng Ling Jiaokeng Village Sinhua Township Tainan Hsien 712 Taiwan R O C The sites are constructed in conformance with the requirements of ANSI C63 4 and CISPR Publication 22 All receiving equipment conforms to CISPR 16 1 1 CISPR 16 1 2 CISPR 16 1 3 CISPR 16 1 4 and CISPR 16 1 5 5 2 ACCREDITATIONS Our laboratories are accredited and approved by the following accreditation body according to ISO IEC 17025 Taiwan TAF The measuring facility of laboratories has been authorized or registered by the following approval agencies Canada Industry Canada Germany TUV Rheinland Taiwan BSMI USA FCC Copies of granted ac
17. mit shall apply at the transition frequencies 2 Emission level dBuV m 20 log Emission level uV m 3 The measurement above 1GHz is at close in distances 3m and determine the limit L2 corresponding to the close in distance d2 by applying the following relation L2 L1 d1 d2 where L1 is the specified limit in microvolts per metre uV m at the distance d1 10m L2 is the new limit for distance d2 3m So the new Class A limit above 1GHz at 3m is as following table Frequency Class A dBuV m At 3m MHZ Average Peak Above too e Page 15 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Report No T101223402 D According to FCC Part 15 33 b for an unintentional radiator including a digital device the spectrum shall be investigated from the lowest radio frequency signal generated or used in the device without going below the lowest frequency for which a radiated emission limit is specified up to the frequency shown in the following table Highest frequency generated or used in the Upper frequency of measurement range device or on which the device operates or MHz tunes MHz Below 1 75 30 1 75 108 1000 108 500 2000 500 1000 5000 5 harmonic of the highest frequency or 40GHz whichever is lower Above 1000 Page 16 This report shall not b
18. ove scans the emissions were maximized by cable manipulation The test mode s described in Item 3 1 were scanned during the preliminary test After the preliminary scan we found the test mode described in Item 3 1 producing the highest emission level The worst configuration of EUT and cable of the above highest emission level were recorded for reference of the final test Procedure of Final Test EUT and support equipment were set up on the test bench as per the configuration with highest emission level in the preliminary test A scan was taken on both power lines Line 1 and Line 2 recording at least the six highest emissions Emission frequency and amplitude were recorded into a computer in which correction factors were used to calculate the emission level and compare reading to the applicable limit The test data of the worst case condition s was recorded Page 11 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc M 6 4 TEST SETUP Vertical Reference EMI Test Receiver Reference Ground Plan For the actual test configuration please refer to the related item Photographs of the Test Configuration 6 5 DATA SAMPLE Meter Measured Reading Level imi Detector dBuV dBuV Freq Emission frequency in MHz LISN Factor Insertion loss of LISN and Pulse Limiter Cable Loss Cable
19. t ent ong ee eee es NA TNI LUM EE SENS pei dcc RR 6 6 TEST RESULTS tea ee easet ese lente all aati an Pu aa un 7 RADIATED EMISSION MEASUREMENT 7T 1 LIMITS OF RADIATED EMISSION MEASUREMENT sse ee eere enne 7 2 TEST INSTRUMENTS 3 5 et reiten ie es deir ases entren ce ee pM addas rau a de sace TA TEST SETUP iiie dte e e rei ete ete etn eee ee E ee E ai 7 95 SAMPLE ices EE LO torte fe ditatem hea LN NE cU INT DL 8 APPENDIX 1 PHOTOGRAPHS OF BUT nu rntrna nuncu nhan ritu nna aki nuum hau uu nina A1 1 PHOTOGRAPHS OF THE TEST Page 3 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc M 1 TEST RESULT CERTIFICATION Product Digital Satellite Receiver Model DBS7000 Brand LEXIUM Applicant WS International 1200 Cobb Parkway North Suite 100B Marietta Georgia 30062 USA Manufacturer WS International 1200 Cobb Parkway North Suite 100B Marietta Georgia 30062 USA Tested January 21 January 25 2011 Standard Result Remarks FCC 47 CFR Part 15 Subpart B Conducted Power Port PASS Me
20. ve test instruments is 12 months and the calibrations are traceable to NML ROC and NIST USA 2 N C R No Calibration Request Page 10 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc M 6 3 TEST PROCEDURES P rocedure of Preliminary Test The EUT and support equipment if needed were set up as per the test configuration to simulate typical usage per the user s manual When the EUT is a tabletop system a wooden table with a height of 0 8 meters is used and is placed on the ground plane as per ANSI C63 4 see Test Facility for the dimensions of the ground plane used When the EUT is a floor standing equipment it is placed on the ground plane which has a 12 mm non conductive covering to insulate the EUT from the ground plane All I O cables were positioned to simulate typical actual usage as per ANSI C63 4 The test equipment EUT installed by AC 120VAC 60Hz main power through a Line Impedance Stabilization Network LISN which was supplied power source and was grounded to the ground plane All support equipment power by from a second LISN The test program of the EUT was started Emissions were measured on each current carrying line of the EUT using an EMI Test Receiver connected to the LISN powering the EUT The Receiver scanned from 150kHz to 30MHz for emissions in each of the test modes During the ab
21. xcept in full without the written approval of Compliance Certification Services
Download Pdf Manuals
Related Search