Magnum 650 Magnum 850 user manual
Contents
1. DN 0 NY Smoke output nozzle WARNING HIGH TEMPERATURE VAPOUR AND SURFACES Quick Start You are no doubt eager to switch on the machine and try it out by making a lot of fog This section tells you how to do that However please also make the time to read the safety and servicing instructions in the remainder of this manual Setting up Locate the machine in a suitably large area with nothing in front of the smoke output Fill the fluid tank with MARTIN JEM approved fluid see page 17 Connect a suitably rated power supply to the machine The power requirements are Magnum 650 2 66A at 230V EU or 6 1A at 120V US Magnum 850 3 4A at 230V EU or 6 6A at 120V US Turn the machine on the on off button and the remote control light will illuminate From cold the machine will take approximately five minutes to reach operating temperature When the light on the remote control has gone out the machine is ready to use When the light on the remote control comes on again it indicates that the machine is reheating this will take approximately two minutes IN connector on the rear panel The remote control is permanently connected to the Magnum 650 Turn on the power switch The red Heat indicator on the remote and the top of the unit will light After about 7 10 minutes the green Ready indicator on the remote and the top of the unit will light The machine is then ready to produce fog To obtain maximum fog output2. yellow or brass blue neutral N silver Before connecting the Magnum smoke machine to power verify that the AC supply is adequately dimensioned for the current draw of the machine The machine requires Magnum 650 2 66A at 230V EU or 6 1A at 120V US Magnum 850 3 4A at 230V EU or 6 6A at 120V US Check that the local AC voltage is appropriate as indicated on the machine s serial number label If your AC voltage is outside the appropriate range do not use the machine Contact Martin Service for assistance Installation and setting up Setting up Fill the fluid container with MARTIN approved fluid see page 17 If using the Magnum 850 connect the remote control to the REMOTE amp IN connector on the rear panel The remote control is permanently connected to the Magnum 650 If you are operating several machines using the machine to machine link function connect up the machines in a daisy chain using RJ45 computer network type cables The maximum total length of cable including the remote cable is 50 metres Machine to machine link is not available on the Magnum 650 to additional machines Do not connect a computer network to the RJ45 remote link sockets on the Magnum 850 Although the connectors are compatible the electrical signals are not and equipment may be damaged Installation and setting up 11 Final checks Before applying power to the Magnum smoke machine verify the following
3. Warning This product is not for household use It presents risks of injury due to electric shock burns falls and respiratory problems Read this manual before operating the machine follow the safety precautions listed below and observe all warnings in this manual and printed on the machine Use the system only as described in this manual and in accordance with local laws and regulations If you have questions about how to operate the machine safely or if you have followed the instructions in this manual and the machine is malfunctioning please contact Martin Service Preventing electric shocks Always ground earth the machine electrically Use only a source of AC power that complies with local building and electrical codes and that has both overload and ground fault protection Before connecting the Magnum smoke machine to power check that the voltage indicated on the machine s serial label matches your local AC power voltage If your AC power voltage does not match do not use the machine Contact Martin Service for assistance Before using the machine check that all power distribution equipment and cables are in perfect condition and rated for the current requirements of all connected devices If the machine or any cables connected to it are in any way damaged defective wet or show signs of overheating stop using the machine and contact Martin Service for assistance Disconnect the machine from AC power before servici
4. e the machine is safely located or installed and meets the location requirements stated on page 10 e the operator is familiar with and able to comply with the requirements for safe operation listed on page 3 e the smoke fluid is one of the genuine Martin fluids listed under Smoke fluid options on page 14 e the machine is electrically grounded earthed e the AC power distribution circuits and lines are adequately rated for the current load Turning on the power Turn on the main power switch located next to the power cable inlet The red Heat indicator on the remote will illuminate amp Turn on the main power switch located next to the power cable inlet The red Heat indicator on the remote and on top of the machine will illuminate for about 7 10 minutes as the machine heats up to operating temperature When the green Ready indicator comes on the machine is ready to make fog To obtain maximum output wait another few minutes for the red Heat indicator to go off as fog output is reduced while the unit is heating up Operating with remote The unit is controlled using the remote control Press the button to generate fog Magnum 650 Magnum 850 F L Fog button Fog button 12 Installation and setting up Priming the machine after fluid out If the machine runs out of fluid it may not pump properly after refilling the fluid due to airlocks in the fluid pipework To prime the machine hold do
5. time 4 Turn the knob to the required wait time 5 Press the TIMER SET button once more Both ON OFF lights will come on to show the timer is programmed The run and wait times are now stored and will be remembered even after the unit has been switched off When valid times are stored but the timer is not engaged the OFF and ON lights remain lit constantly To start the timer using the times you ve set press the FOG TIMER ENGAGE button briefly To turn off the timer press the FOG TIMER ENGAGE button briefly again When the timer is engaged the ON light will come on during the On Run time and the OFF light will come on during the Off Wait time unchanged press TIMER SET twice This will take you directly to setting the Off time without changing the On time oO If you only want to change the Off Wait time leaving the On Run time To find out what the current time settings are press TIMER SET then rotate the knob slowly until the ON light begins to flash very rapidly The knob is now set to the current run on time Press TIMER SET once and rotate the knob slowly again until the OFF light begins to flash very rapidly The knob is now set to the current wait off time Press TIMER SET again to get back to normal Setting the one shot timer The one shot timer allows you to pre program the length of the fog burst This can be useful if you want to have a fixed time burst of fog which you can repeat a
6. wait another couple of minutes for the Heat indicator to go out If using the Magnum 850 connect the remote control to the REMOTE Making fog Once the machine has heated up hold the button on the remote to start the fog output Installation and setting up 10 DANGER DO NOT operate the Magnum smoke machine until you have read and observed all the precautions listed under Safety information on page 3 The Magnum smoke machine should be located on the floor or a suitably robust surface The machine can operate in any orientation from 45 degrees upwards to 45 degrees downwards Steeper tilting may cause fluid leakage Do not suspend the machine over areas where people will be underneath Ensure that there is at least 100mm clearance all round the machine and at least 600mm in front of the smoke output Before using the machine ensure that a grounding type earthed power plug that fits the local power outlets is installed on the power cable DANGER Make sure the power plug is correctly rated e For EU 230V use fit a plug rated 6 amp minimum e US 120V models must be fitted with a plug rated 10 amp minimum When installing the plug follow the plug manufacturer s instructions and connect pins as follows yellow and green wire to ground earth blue wire to neutral and brown wire to live The table below shows some common pin identification schemes wire function marking screw colour brown live D
7. Clean the outer casing with a damp cloth only Fuse replacement The main fuse for the Magnum 850 smoke machine is located on the electronics board inside the unit The fuse for the Magnum 650 is located in a tray on the mains connector DANGER Disconnect the power supply before removing any covers Live parts inside 850 To replace the fuse disconnect the power cord from the supply unscrew the screws holding the top cover of the unit and remove the cover The electronics board is located at the back of the unit near the remote control sockets Remove the fuse holder cover and pull out the fuse 650 To replace the fuse disconnect the power cord from the mains plug on the rear panel Using a screwdriver pull out the small fuse compartment underneath the plug Lift out the fuse Remove the spent fuse and replace with one of exactly the same size and rating The fuse type is indicated below Contact Martin Service if the fuse blows repeatedly Magnum 850 120V 10AT 230V 6 3AT Magnum 650 120V 10AT 230V 5AT Basic service Troubleshooting Problem Probable cause s Suggested remedy Machine not at operatin Machine will not produce fog temperature j gt Wait 10 to 15 minutes when remote control Fog button pressed Ensure mains power switch Machine not powered up on and AC power is OK Smoke output is weak Machine requires priming Prime machine page 13 Wet greasy non uniform smoke output fluid drips or spits fro
8. P N 35010029 D Magnum 650 Magnum 850 user manual Salely e dun Eden GE 3 o A O O 6 PFOGUEL GESCHPION EE 6 Features ala Qlance EE 6 Product aglals Ma9RUM 690 22 a a 7 Product details Magnum 850Quick Giant 8 QUER Sale ee ee rer ee ner 9 Seting UP Een ee 9 DE dale be 9 Installation and Seting Uan uote a e a EA 10 Beie wei EE 10 AG ele 10 Senno UD dd ad 11 FINAL GIN CCI S 2 ee dora 12 TUNING ON Me DOWEL a ie 12 Operating Wwiln Te mote rasca decada cin octal stas 12 Priming the machine arer MUG SUR ecen 13 What TAS Elte an En DEE 13 lte E Ee 14 Timer remote Magnum 850 only ooocccccoccnnccnoccnnocnncnnconnconcnnnnonononaconnonnnrnnonnnrnnnnnnrnnnonanenns 14 Manta TIMING EE 14 SEMING TOG OULOUT ISVS dun io loas 15 Setting the ue Edel TEE 15 Setting the one shot Hmer nn nnnnnnnnennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnennnnnn san 15 DIsabling Umer lee r T 16 Meaning of remote control lights nennen nennnnnnnnnnnennennnn nennen 16 FOG MUIDE Sec ee Ba O OS 17 Basic SONICO EE 18 ET le e BEE 18 FUSE le men ti eae raed atu Meet rao er seicae ea ec eae 18 Neie Leet ae EE 19 SPECHIEAUONS rara 20 2 Safety information Safety information The following symbols are used to identify important safety information MAMADA Caution Safety Caution Burn Danger Caution Fire hazard Risk of hazard Hot Hazardous hazard personal injury surface Do not voltage Contact touch will cause electric shock
9. e following functions The red HEAT light and the green READY light are also duplicated on the top of the machine itself HEAT READY meaning no lights Machine is not powered or remote is not connected Heat Machine is heating but is not yet up to operating temperature Machine is heating and has reached minimum operating heat ready temperature Fog output level may be reduced while heating Machine has finished heating and is at full operating ready temperature OFF ON meaning no lights Timer is disabled both on Timer is programmed but not enabled OFF lit Timer is running currently in Off Wait period ON lit Timer is running currently in On Run period ON flashing The timer ON time is currently being programmed ON lit OFF O flashing The timer OFF time is currently being programmed Optional accessories Magnum 850 only Fog fluid types The following types of Martin Jem fog fluid are suitable for use in this machine Each produces a different effect as described below Martin supplies high quality fog fluids that are based on ultra pure deionized water Use only the following genuine Martin Jem fog fluids No other fluid is suitable for use DANGER The Magnum smoke machine can run safely only on the specific smoke fluids it is designed for Use ONLY the Martin Jem smoke fluids designated in this manual NEVER use any other type of fluid or toxic gas may be produced You will probabl
10. emperature Tamax nennen nennen nennen 40 C 104 F Exterior surface temperature steady state at 20 C ambient 40 C 104 F Approvals European EM EN61000 6 3 EN61000 3 2 EN61000 3 3 Seier E E EN 60 335 1 IMIMUNIV olor EN61000 6 1 EN61000 4 2 EN61000 4 3 ETLapprovals CETUS aia UL60335 1 CSA E60335 1 Specifications Included items EU Model 3m 9 8ft IEC power cable 3x1 0mm2 with Schuko male connector 3m 9 8ft IEC power cable 3x1 0mm2 with no male connector US Model 2m 6 5ft US power cable 18AWG with US male connector UL approved 1 x fluid container empty Accessories Timer remote Magnum 850 only ooccccccccnccccncccnoncconccononnnnnnnnnancnnnnss P N 92765032 Ordering information Martin Magnum 650 smoke machine 120V uuuunsesennnnssnnnnneennnnnn P N 92228810 Martin Magnum 650 smoke machine 230V uuunennsennnnnnennnnnnnennnnnn P N 92228811 Martin Magnum 850 smoke machine 120V uunenesessnnnnennnnnnnennnnnn P N 92229110 Martin Magnum 850 smoke machine 230V sceceeeesseeeeeeeeaeees P N 92229111 Martin Magnum 850 remote Control P N 92765030 Specifications 21
11. he output at smooth floors Floors and surfaces may become slippery Check these frequently and wipe dry as necessary to avoid any danger of slipping Ensure at least 2m visibility in areas where smoke is being produced Safety information Smoke fluid contains food grade glycols in solution but may present health risks if swallowed Do not drink it Store it securely If eye contact occurs rinse with water If fluid is swallowed give water and obtain medical advice Preventing breathing problems A smoke machine can operate safely only with the smoke fluid it is designed for Use the machine only with fluids specified under Smoke fluid options on page 17 or you may cause the release of toxic gases presenting a severe health hazard You will also probably damage the machine Do not create dense smoke in confined or poorly ventilated areas Do not expose people with health problems including allergic and or respiratory conditions such as asthma to smoke output Do not point smoke output directly at a person s face or at face height Safety information 5 Product overview Product description The Magnum 850 and Magnum 650 smoke machines from Martin provide a uniquely flexible and convenient solution to a wide range of smoke requirements whether permanently installed or taken on the road The machines feature a unique new design that encompasses what the Magnum range is all about state of the art technology high qua
12. lity and ruggedness The Magnum 650 delivers a heavy punch of fog It s tough and rugged enough to meet the demand of mobile discos and parties The Magnum 850 is a higher power fogger suitable for larger venues or night clubs This manual contains instructions for both the Magnum 650 and Magnum 850 machines Where the Magnum 850 is different you will see this symbol Congratulations on your purchase of the Magnum smoke machine from Martin Details of the full range of Martin products are available on our website at www martin com Features at a glance e Attractive and rugged design e Machine to machine link Magnum 850 only e Continuous operation at reduced output Magnum 850 only e 730W Magnum 650 790W Magnum 850 e litre fluid capacity e Pushbutton remote control hardwired on Magnum 650 e Optional timer remote Magnum 850 only e Thermal fault protection device 6 Product overview Product details Magnum 650 Carry handle Power switch Fluid container Remote cable Fluid level viewer Power inlet plug and mains fuse Smoke output nozzle WARNING HIGH TEMPERATURE VAPOUR AND SURFACES Product overview 7 Product details Magnum 850 Heat Red Ready Green indicators See Ue fee NI Remote machine link sockets Magnum 850 only Main power switch Fluid container Power inlet plug Fluid level viewer e H un O 09
13. m nozzles or very Incompatible smoke fluid Use only approved fluid loud noise when firing Mains fuse blown Replace fuse page 18 machine Machine appears dead No power at AC cable inlet Sheck Power cable and circuit breaker Troubleshooting 19 Specifications 20 Magnum 650 Magnum 850 Physical A E 29SM eeceeteyact sew 450mm YIO SE SCENE 205mm ale ee R lis 244mm Dy WER Seelen LN 9 9Kg Performance Eflect coVelage ware 160M Aemin eee 200m min Operating INe areas Cycles continuous Warm UD UMG cc a 7 5 MINUTOS 8 minutes Safety device nenn OTP device DTP device Control and programming Gontrol OPUONS suas ad remote remote timer remote DMX channels eege een VI DEE n a Fluid system EEN IEN 1 litre Fluid CONSUMPTION occccoccncnnccncccncnnnnncnnnnncnonnnonos 23M MIN iii 35ml min Eompaliblellulds esse DIRA een DJ ZR Connections N ae RG EE n a Remote machine link nee bardwirerd no RJ45 x2 AO ele EE IEG DIUG SE IEC plug Electrical AG VOlldge anne 120V 230V 50 60Hz 120V 230V 50 60Hz Main fuse 120V US version ooccccccccccnccconcnncnonos TOA Teme 10AT Main fuse 230V EU version c cocccccccccccccnccccncncnnno Kee 6 3AT Power usage 120V US version 730W GI 790W 6 6A Power usage 230V EU version 620W 2 664A 790W 3 4A The following specifications apply to both machines Thermal Maximum ambient t
14. ng and when not in use This system is not waterproof and should not be exposed to wet outdoor conditions Do not immerse in water or any other liquid Do not expose to high pressure water jets Do nat spill fluid over or inside the machine If fluid is spilled disconnect AC power and clean with a damp cloth If fluid is spilled onto electronic parts take the system out of service and contact Martin for advice Do not remove the covers or attempt to repair a faulty machine Refer any service not described in this manual to Martin Safety information 3 Do not operate the machine if any parts are damaged defective or missing Moisture and electricity do not mix Do not aim smoke output at electrical connections or devices If the supply cord is damaged it must be replaced by a special cord or assembly available from the manufacturer or its service agent Preventing burns and fire The smoke produced by the machine is hot enough to cause burns when it leaves the nozzle and very hot droplets of fluid escape occasionally Keep people and objects at least 1 meter 39 inches away from the smoke output nozzle Do not touch the smoke output nozzle during or after use it becomes extremely hot and remain hot for several hours after the machine has been shut down Smoke output contains glycol a flammable alcohol that burns with an almost invisible blue flame Do not point smoke output at sources of ignition such as open flames or py
15. rotechnic effects Do not attempt to bypass thermostatic switches fluid sensors or fuses Replace fuses only with ones of the type and rating specified in this manual for the machine Provide a minimum free space of 100mm 4 inches around the machine Provide a minimum free space of 500mm 20 inches around fans and air vents and ensure free and unobstructed air flow to and around the machine Keep the machine at least 600mm 24 inches away from combustible and heat sensitive materials Do not operate the machine if the ambient temperature Ta is below 5 C 41 F or above 40 C 104 F Do not operate the machine if the relative air humidity exceeds 80 Preventing injuries Ensure that the surface on which the machine is located or installed can safely hold the weight of the machine This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance Do not install the machine over areas where people are present Verify that the machine s temperature setting is suitable for the type of fluid in use whenever changing fluid or resetting the default menu values Smoke machines can cause condensation Do not point t
16. so set the fog output level using the knob Manual firing Hold down the FOG button The machine will produce fog until you release the button You must hold the FOG button for one second or more If you hold the FOG button for less than one second the unit will enter timer mode unless the timer is disabled If a long burst of fog is produced after a time the fog output level will be automatically reduced to keep the machine temperature within the operating range This allows continuous operation so that the machine does not have to stop and re heat 14 Optional accessories Magnum 850 only Setting fog output level Set the knob to the desired output level while firing the machine The fog output level is always set by the current position of the knob whether manually firing or in timer mode Setting the Automatic Timer The Automatic Timer allows you to set the machine to keep producing timed bursts of fog without anyone having to press any buttons You need to set two times the run on time during which the machine will produce fog and the wait off time during which the machine will idle 1 Press the TIMER SET button The ON light will flash You are now setting the On Run time 2 Turn the knob to the required run time as shown on the outer scale of the knob OFF 255 seconds 3 Press the TIMER SET button once The ON light will come on static and the OFF light will flash You are now setting the Off Wait
17. t will by pressing the fog button 1 Press the TIMER SET button The ON light will flash You are now setting the On Run time 2 Turn the knob to the required run time as shown on the outer scale of the knob OFF 255 seconds 3 Press the TIMER SET button once The ON light will come on and the OFF light will flash 4 Turn the knob fully right to where OS One Shot is marked 5 Press the TIMER SET button once more Optional accessories Magnum 850 only 15 16 The timer is now programmed to one shot mode and this will be remembered even after the unit has been switched off To produce a timed burst of fog press the FOG button briefly To stop the timed fog output early press the FOG button briefly again Disabling timer mode If you wish to simplify the remote control you can disable the timer function This means that a short press on the FOG button will just produce a short burst of fog and the timer will not be enabled 1 Press the TIMER SET button once The ON light flashes 2 Turn the knob fully left to the OFF section 3 Press the TIMER SET button again The zero times will be stored disabling the timer This will be remembered even after the unit has been switched off The ON and OFF lights remain off when the timer is disabled To re enable the timer function store some non zero times as described above Meaning of remote control lights The four lights on the remote have th
18. wn the FOG button and keep the button held until the fog output is strong and steady If the machine is left to run when out of fluid damage will be caused to the pump which may cause premature pump failure What the status lights mean The red heat light on the remote control has the following meanings Machine is heating but is not yet up to operating temperature Machine is either ready to fire or not powered check mains switch light for status The red green Heat Ready lights on the top of the machine have the following meanings HEAT READY meaning no lights Machine is not powered reai Machine is heating but is not yet up to operating temperature Machine is heating and has reached minimum operating heat ready temperature Fog output level may be reduced while heating Machine has finished heating and is at full operating ready temperature Installation and setting up 13 Optional accessories Magnum 850 only Timer remote amp The timer remote is an optional accessory for the Magnum 850 Output level timer programming knob Machine ready to fog light ve Machine heating light Fog Timer engage button lees ligh Timer Off light A ERR Timer set button Martin The timer remote can be used in these ways e Manual firing by holding down the FOG button e Automatic fog bursts using a repeating timer e You trigger a timed burst of fog using the one shot timer You can al
19. y also cause damage to the system that is not covered by the product warranty Do not dilute smoke fluid with water or any other liquid Discard smoke fluid if it becomes contaminated Regular DJ Fluid DJ mix Regular DJ fluid is an economical fluid that gives a good medium density smoke well suited for atmospheric effects Pro Smoke Super ZR mix Pro Smoke Super fluid is a high quality general purpose fluid that produces a dense white airborne fog with medium dispersal time lts medium to high index of refraction permits both good atmospheric effects and denser white outs Fog fluid types 17 Basic service 18 Before servicing the Magnum smoke machine read and observe all the precautions listed in Safety information on page 3 Any service not described in this section must be carried out by a Martin service technician Excessive dust smoke fluid and dirt buildup will degrade performance and cause overheating and damage to the machine that is not covered by the product warranty To maintain adequate cooling dust must be cleaned from the outer casing and air vents of the machine periodically Isolate the machine from power and allow to cool completely before cleaning The smoke output nozzle remains hot for up to 10 hours after use e Remove dust from the air vents with a soft brush cotton swab vacuum or compressed air e Clean smoke fluid residues from the fog output of the machine using a damp cloth e
Download Pdf Manuals
Related Search