- Maxi-Cosi
Contents
1. e Do not dry clean e All other surfaces should be cleaned with a mild soap and water e Never clean with bleach or spirit type cleaners e Do not use the restraint without the cover e Check the webbing for fraying Remove trim for cleaning TO REMOVE HEADREST TRIM 1 Move headrest to highest position 2 Remove the 2 elastic straps on the back of the headrest 3 Peel the trim off the headrest 4 Remove Air Protect cells x2 Important Do not wash trim with Air Protect cells still inside TO REPLACE HEADREST TRIM 1 Move headrest to highest position 2 Replace Air Protect 3 Put the headrest trim on 4 Clip the 2 elastic straps to the plastic tabs at the rear of headrest TO REMOVE SEAT TRIMS 1 Undo shoulder straps from the splitter plate 2 Pull straps through the cover 3 Remove the 4 plastic clamps on the front and rear of seat 4 Remove the seat trim from the seat TO REPLACE SEAT TRIM 1 Put the seat trim on the seat 2 Feed the shoulder straps through the cover 3 Attach the plastic clamps 3 Attach the shoulder straps to the splitter plate NOTE ENSURE HARNESS IS NOT TWISTED Take extra care to be sure the harness is reinstalled correctly and the shoulder straps are of equal height through both the trim and the harness slots of the seat Care and maintenance Remove insert for cleaning To remove insert To remove the insert separate the snaps in 2 places Refer to illustrations Undo th2. rerrnrn renee Pere cererr rere ere PR ference Terres treater ai 34 STE INS EEE ENER 35 MAXI COSI Dear customer Congratulations on the purchase of your brand new Maxi Cosi car seat we hope you and your little one will have plenty of hours of fun together Our car seats are produced with the greatest care and craftmanship backed by a 6 year warranty on the seat and 3 year warranty on the trimming In the event of a car accident your Maxi Cosi child restraint may have unseen damage from crash forces The Maxi Cosi Accident Exchange Service offers new for old Maxi Cosi child restraint replacement in the event of an accident giving you peace of mind knowing your child is corectly protected So there is nothing for you to worry about just sit back and enjoy the ride where ever it may take you We would love to hear from you Nothing makes us happier and encourages us to continue developing the very best products available than hearing how it helped you enjoy your time together on the go Feel free to share you story on our Facebook page or our website Enjoy your ride The Maxi Cosi Team Need assistance Call our Customer Service Centre 1300 809 526 Monday to Friday 8 30am 5 00pm AEST or send an email customerservice dorel com au www maxi cosi com au f maxicosi australia Read and follow all of the installation instructions for maximum protection If you have any questions regarding the installation or
3. use of this restraint please contact Dorel Australia or agent or a child restraint fitting station authorised by the relevant transport authority or in New Zealand to consult the agent for the vehicle e To be used only in a rearward facing position until the infant s shoulders reach the lower shoulder height marker approximately 12 months of age Then to be used in a forward facing position until the child s shoulders reach the upper shoulder height marker approximately 4 years of age e Continue to use this child restraint until the child reaches this limit e Do not use forward facing until child s shoulders are above the lower shoulder height marker e Infants are at risk of serious injury if they face forward too early e Children are at risk of serious injury if they move to booster seats too early e Children who have outgrown this restraint are safest in a larger child restraint with an in built harness or a booster seat until their shoulders reach the upper shoulder height marker of the restraint GENERAL e Use the restraint exactly as shown in the instructions e Supervision of children is needed because they may be able to undo the buckles e DO NOT LEAVE CHILDREN UNATTENDED IN THE CAR e Do not alter or modify this restraint e Repairs must only be done by the manufacturers or agent e Do not allow the restraint to come into contact with polishes oils bleach and other chemicals e Destroy the restraint if i
4. ER TO CAR OWNER S HANDBOOK FOR LOCATION OF UPPER ANCHORAGE POINTS REFER TO A CHILD RESTRAINT FITTING STATION IF NO UPPER ANCHORAGE POINTS ARE IN THE MOTOR CAR e Always check the measurements between the front of the seat back of the rear seat and all front seats in the car in which the child restraint is intended to be used to ensure that the space is sufficient e Care and attention be given to ventilation and shading of the occupant e TO BE USED WITH A LAP SASH LAP ONLY SEATBELT OR ISOFIX LOW ANCHORAGES IN THE FRONT BACK OF MOST CARS WITH FORWARD FACING SEATS e The use of child restraints in the front seat may be restricted for children of specific ages by local legislation Please check with your local legislation regarding any restriction for child restraint If a car has two or more rows of seats children under four must not travel in the front seat If all seats other than the front seats are being used by children under seven years children aged between four and six years inclusive may travel in the front seat provided they use an approved child restraint or booster seat e Use of aftermarket accessories i e items not provided in the box with the child restraint can reduce the safety provided by child restraint and may cause injury or death For approved aftermarket accessories please refer to page 12 e Please contact Dorel Australia Customer Service with any questions or concerns Parts list RON oo Air
5. Euro amp Hera Convertible Car Seat To be used only in a rearward facing position until the infant s shoulders reach the lower shoulder height marker approx 12 months of age Then to be used in a forward facing position until the child s shoulders reach the upper shoulder height marker approx 4 years of age IMPORTANT KEEP THIS BOOKLET IN THE PLACE PROVIDED ON THE CHILD RESTRAINT Table of Contents Welcome letter o cccccccccccccccscsesescseseseecsescseecaescecseseacececeeacecaeacecesaeaeaseeesacaseseseeeeetenes 3 Warnings v asvavasktambakserqalaimaesekareegeheiaumnanve 4 PartSistatauva2x4a42ad42 dsaeS era nd 8 Transition period from infant to toddler use s smrnrsrsrrrrvrrrsrrvrvrvrvrrrrrrnenrnrnn 10 Vehicle information arrnrnrrnrnrrrrs rn er nr ar nnser an nsns nr evnen nven nesen eresesnsnrerssnserernsnsnsennnn 12 Upper anchorage fitting installation oo cececcecccceseseeeeteseeceeeseecesseeeeseeeeeseeeteeeeeetes 12 Anchorage fitting installation sssrinin 13 Location of anchor fitting oe ee eeeceseseseseseseecseseetecsescecenseseesansnseesenseetesaneeesatneeetatens 14 Upper anchorage fitting installation for sedans only cesscssecesseeseeeeseseeeeeees 15 Correct rearward facing vehicle position oo eeeceeecesseeseseeeteeeseeseeseseesateceeeseteeeeeees 16 Installation uagraavamvdrsdraa E ered eee eee ere 17 Angle adjustment mosini iie a ET RE TRR nOn 17 Preparing infant seat to fit your Ch
6. Lock washer Nut OMG Front of vehicle Figure 6 Vehicle information Correct rearward facing vehicle position Some seating positions in your vehicle may NOT be safe for this safety seat Some vehicles do not have any seating positions that can be used safely with the seat If you are not sure where to place the infant seat in your vehicle consult your vehicle s owner s handbook Vehicle Seat Location Requirements Children are safer when properly restrained in rear vehicle seating positions Whenever possible secure the infant seat in the centre position of the seat directly behind the front seats CORRECT USE CORRECT USE Figure 8 O 640mm Figure 9 IMPROPER PLACEMENT OF THE SAFETY SEAT INCREASES THE RISK OF SERIOUS INJURY OR DEATH Installation Angle adjustment Position seat ensuring that the angle is no greater than 40 from horizontal plane Angular adjustment is achieved by adjusting the base Refer to page 19 for base adjustment am O Front of vehicle Figure 10 e DO NOT install convertible child restraints excessively reclined ensure the angle is no greater than 40 e DO NOT adjust harness or tether strap hardware such that it sits too close to the occupant e Ensure that correct seatbelt path is used and that the restraint is installed in the correct direction for rearward facing application Refer to page 22 e DO NOT wrap baby in a blanket or swaddled as infant c
7. an be ejected and killed in an accident e Ensure the harness fits the baby firmly e Ensure that any blanket or other covering may only be placed over the harness after the harness is adjusted firmly e The infant s legs are not be bound or wrapped together and the arms are not bound or wrapped together Installation Preparing infant seat to fit your child You MUST make these adjustments with your child before you install the child restraint in the vehicle Please adjust harness according to the infants shoulder height prior to installation Configuring the harness belt for shoulder height 1 Lift the harness release lever at the front of seat 2 Pull one side of the shoulder strap to loosen 3 Press red button to release buckle assembly for ease of child fitment Pull harness straps over sides of infant seat Place child in seat Adjust headrest height 4 Rotate harness height adjustment levers inward Move headrest to the proper height and lock into place 5 Fasten buckle assembly See Page 19 Pull the adjuster belt at the front of the seat until the harness belt lies firmly against the child e Always adjust the height of the shoulder straps as the child grows e Failure to fasten and tighten the harness system correctly can result in serious injury or death Installation Preparing infant seat to fit your child contd Figure 13 To fasten buckle assembly Release Press the red button to release the b
8. asten with an audible CLICK If sticky liquids Such as baby food fruit juice etc get into the buckle it may become sluggish and you will not hear a CLICK The buckle should be cleaned by following the steps below push metal rod into slot Figure 30 Figure 31 1 Fold seat cover and foam back from buckle using a flat edged screwdriver gently lift one end of rod out releasing crotch buckle Repeat for other side 2 As illustrated in Figure 29 place the buckle unit under running water 40 degrees Celsius Let the water flow through the mouth of the buckle for one minute 3 Simultaneously latch and unlatch the tongues into the buckle several times until a strong audible click is heard Refer to Figure 30 4 If you still cannot hear a strong audible click after latching the buckle several times repeat steps 2 and 3 5 DO NOT oil any part of the buckle 6 Allow buckle to dry 7 Refit crotch buckle ensuring RED button is facing out 8 Thread the webbings as shown with arrows in Figure 31 9 Put the 2 metal rods back into the webbing loops and push into the slots 10 Pull the buckle to make sure that it is fitted properly 11 If the buckle does not return to original working order contact Dorel Australia Customer Service on 1300 809 526 Care and maintenance Care instructions e Seat trim may be removed for cleaning Don t forget to remove the instruction manual e Tumble dry 10 15 minutes on low heat
9. d s shoulders be more than 25mm below Child Shoulders SHOULDERS BELOW THIS LINE WHEN HERRE EEE EEE EM HEADREST AT HIGHEST POSITION OMG Front of vehicle gt Figure 24 The child restraint is unsuitable for the occupant when the shoulders are below the lower marker or above the upper marker The child needs to be moved into the next form of child restraint booster seat when they reach the top shoulder height marker DO NOT LEAVE CHILDREN UNATTENDED IN THE CAR Installation Forward facing installation using seatbelt TODDLER 12 MONTHS TO 4 YEARS OLD NOTE Before you start installation adjust the shoulder straps and headrest to fit your child Refer to page 14 1 Adjust the child restraint to the forward facing position by placing restraint on back seat of vehicle in line with an anchorage point FORWARD FACING BELTPATH 2 Thread the vehicle seat belt through the YELLOW forward facing belt path 3 Place one hand on seat press the child restraint into the vehicle seat and pull on seatbelt to remove slack 4 Attach the upper anchorage strap to the anchorage point Adjust until all the slack is removed NOTE If the car seatbelt is not long enough to secure the child restraint DO NOT USE SEAT BELT EXTENDERS Lower connectors installation LOOK FOR THESE SYMBOLS FOR ATTACHMENT IN VEHICLE ISOFIX IMPORTANT Do not attach the lower attachment connectors of two s
10. e buckle and pull the insert out To replace insert Feed the crotch part of the buckle through the opening slot in the insert Place the shoulder straps as illustrated and attach the snaps in 2 places Fasten buckle assembly Figure 37 VERY IMPORTANT Only replace the cover with a manufacturer s supplied replacement cover with identical shoulder height markers or a replacement cover meeting AS NZS 8005 Accessories if supplied Belt mates NOTE Before fitting covers remove harness from splitter plate see page 19 e Fit belt mates to harness strap by threading the strap through the belt mate e Repeat for both sides e Thread harness straps back through harness slots NOTE Refit splitter plate before continuing see page 19 The next seat for your child option 1 Harness forward facing car seat To be used only in a forward facing position by a child whose shoulders are above the lower shoulder height marker approximately 6 months of age until the child s shoulders reach the upper shoulder height marker approximately 8 years of age option 2 Booster seat To be used with a lap sash seatbelt by a child whose shoulders are above the lower shoulder height marker approximately 4 years of age until the child s shoulders reach the upper shoulder height marker approximately 6 to 8 years of age Can also be used with child harness that is approved for use with this boo
11. ed e Vehicle trim Vehicle metal CCF structure sur Front of vehicle gt Figure 4 FOR CARS NOT FITTED WITH A CHILD RESTRAINT UPPER ANCHORAGE POINT For sedans only Drill a 9mm diameter hole in the parcel shelf on the centre line of the seating position as shown in Figure 4 Install the anchor bolt as shown in Figure 5 It is recommended that this installation be carried out by a child restraint fitting station or licenced motor mechanic For vehicles other than sedans In Australia consult your nearest child restraint fitting station or traffic authority for vehicle inspection to find the best correct position for the placement of the upper anchorage point and for the correct attachment bolt length and use of spacers In New Zealand consult the agent for the vehicle WARNING CHILD RESTRAINTS MUST NOT BE ATTACHED TO UNSOUND METAL OR TO WOOD OR SYNTHETIC STRUCTURES WHEN DRILLING THE 9mm HOLE DO NOT DRILL THROUGH FUEL LINES FUEL TANKS ELECTRICAL WIRING OR RADIO SPEAKERS WEBBING STRAPS MUST BE PROTECTED FROM SHARP CORNERS AND EDGES THE ANCHOR FITTING MUST BE USED ONLY AS DESCRIBED ABOVE IT MUST NOT BE HOOKED ONTO ANY OTHER OBJECT Vehicle information Upper anchorage fitting installation for sedans only Centre line of seating position Figure 5 I Attachment bolt Anchor fitting Spacer s gt if required s Vehicle trim Vehicle metal structure e Reinforcing N J washer e
12. eparate child restraints to the same ISOFIX low anchorages in your car Always attach the top tether strap to the child restraint upper anchorage in your car Child restraint lower attachment connectors and the ISOFIX low anchorages in your car are designed to withstand only those loads imposed by a correctly fitted child restraint e Never place a child rear facing in a seating position with an active frontal airbag This can result in serious injury or death e Do not use the lower connectors along with the vehicle lap or lap shoulder belt e Check lower connector strap before each use Use only if the strap can be tightened properly and securely e Do not use both the lower connectors and vehicle belt at the same time e Failure to follow these warnings can result in serious injury or death e Failure to securely attach child restraint to base can result in serious injury or death Lower connectors installation Rearward facing Set base in position 3 High Swing stabilising arm into position Place restraint facing rearwards on back seat of vehicle in line with an anchorage strap anchorage point Fasten the lower attachment connectors to the anchor in the vehicle seat located in the vehicle seat bight Repeat for other side of base Pull on the adjuster strap next to the lower CONNECTORS connectors and remove slack Repeat for Figure 27 other side of base 6 Check for the green indicator on the lower connecto
13. fittings are available from various stores Anchor bolt kit ref no 014400 Locking clip ref no 014401 Extension straps 300mm ref no 014398 Extension straps 600mm ref no 014399 Vehicle information Anchorage fitting installation Child restraints must be used correctly to provide proper protection for your child The anchorage system on child restraint must be used in the correct way CORRECT Make sure there is no slack in the top strap and the attachment clip is upright in the anchorage fitting INCORRECT The clip must not lie flat on the anchorage fitting INSTALLATION CORRECT INCORRECT Make sure there is no The clip must not slack in the top strap lie flat on the and the attachment anchorage fitting clip is upright in the anchorage fitting Figure 1 Anchorages in vertical panel at rear of vehicle Figure 2 Floor mounted anchorages Vehicle information Upper anchorage fitting installation FOR CARS FITTED WITH A CHILD RESTRAINT UPPER ANCHORAGE POINT Locate the upper anchorage point behind the rear seating position consult the car owner s handbook for the location of the upper anchorage point Remove the thread plug from the parcel shelf floor roof and install the attachment bolt as shown in Figure 3 CAUTION DO NOT OVERTIGHTEN THE ATTACHMENT BOLT MAXIMUM TORQUE 20 Nm Attachment bolt Lock washer e ET sier fitting Spacer s e if requir
14. ild m senvvvrvvvvvrvvrrvrrrrrrnrinn 18 Shoulder height marker rearward facing cssesssesssescssesseseecseesessesseeeeeees 21 Rearward facing installation using seatbelt 0 cece eeseetetetsteeteteeeeeeee 22 Correct forward facing vehicle position m vmsererernrvrrrrrerrrrrrrsrerrrrrsrrrerersrnrrrennnn 23 Shoulder height marker forward facin9 ccecesseseseesseseecseeesessesseesseeeesseaeens 24 Forward facing installation using seatbelt oo ceeeeeeeeceeeeseeeeseeteeseeteeeeseseeteeseeeees 25 Lower connectors installation isonrrnsnnorrrrrrrrrrrrrrrrrrrrrrrrrrrnrrrrrrnnrnrrrsnrnrennnn 26 ReamerdTadngunurvdenreeterat danene E E OEE 27 TONNE Eee IN S sss T E T A 27 Installation e encecn panan 28 Installing locking clip optional EEE AR 28 Care and maintenance 0 00 ceccccccscsesssesesesessesescecsnsessnscensesssanecetsesesanseeeseseserenes 29 Cleaning instructions for DUCKIE ccecccesesescsseeseeeseeeeecseseeteeeseseceeseeieeetseseseeeeeees 29 Care INStuetlons sneri e a 30 Removing trim for cleaning cccecseseteeseeetseseeesesceeeeeeeesseeeeseeaseseseeeseeerteeeeeenees 30 Removing insert for cleaning c ccccccesecseseseesseseececseseececeeseecaeseseecaeseeeesanseseesanseeeans 31 Accessories if supplied 0 0 0 0 ccc cscececetsesecessesesssessessseseessaseeesaaneeeananes 32 BAL MASS aa 32 The next seat for your child oo ccs ccescsessssseecssssscescesssssssesssessesstssssesersaees 33 NRS eer
15. ing clip optional Using the seat belt locking clip to convert a lap sash belt to a lap only belt NOTE Locking clip can be fitted on either side depending on the vehicle seatbelt and child restraint configuration 1 Using a locking clip Figure A to convert a lap sash belt to a lap only belt 2 Hold the lap and sash straps Figure B together Thread webbing still pinched into the locking clip one side at a time Figure C amp D 3 Repeat step 2 for the other slot in the locking clip Figure E amp F Feed the straps through the locking clip to remove any slack 5 If the locking clip is on correctly it will hold the lap belt securely if the lap belt slips repeat the previous steps 6 Locking clips are available from most speciality outlets or from Dorel Australia Customer Service 1300 809 526 A NOTE The locking clip must be removed when the child restraint is not installed to allow other users to use the seatbelt as a lap sash seatbelt The locking clip shall not create unacceptable slack in the seatbelt Care and maintenance Cleaning instructions for buckle Follow the manufacturer s instructions at all times Before removal ensure you have carefully noted the way which the various parts are attached to the seat so as to facilitate reassembly Your child car seat is equipped with a buckle designed to give your child maximum protection during proper use When working properly your buckle should always f
16. protect cell x2 Height marker Stabilising arm Harness release lever under flap Harness tightening strap Base adjustment button two positions 7 Base 8 Mesh pocket for lower connector x2 9 Buckle 10 Belt mates x2 11 Infant insert Parts list 12 Adjustable headrest 5 positions 13 Top tether strap 14 Hook 15 Anchor kit 16 Splitter plate 17 Forward facing belt path 18 Lower connectors x2 19 Tension indicator x2 20 Rearward facing belt path 21 Storage pocket instruction manual amp excess tether strap webbing 22 Top tether strap adjuster Transition period from infant to toddler use L height k Rearward facing ower height marker MUST BE REAR FACING WHEN HERRER E EEE EEE SHOULDERS BELOW THIS LINE NOTE Turn the restraint from rearward facing to forward facing once your child s shoulders reach the lower height marker O O Front of vehicle P REARWARD FACING BELT PATH gt Figure 1 Forward facing Upper height marker SHOULDERS BELOW THIS LINE WHEN HERE EEE EEE HEADREST AT HIGHEST POSITION FORWARD FACING BELT PATH Transition period from infant to toddler use cont d e To be used only in a rearward facing position until the infant s shoulders reach the lower shoulder height marker approximately 12 months of age Then to be used in a forward facing position until the child s shoulders reach the upper shoulder height marker approximately 4 year
17. r slots which are nearest to the child s strap shoulders but not lower than the child s shoulders MUST BE REAR FACING WHEN HEER EEE EEE SHOULDERS BELOW THIS LINE OMG Front of vehicle gt Figure 18 Installation Rearward facing installation using seatbelt NEWBORN TO 12 MONTHS 1 Set base in position 3 High 2 Swing stabilising arm into position 3 Place restraint facing rearwards on back seat of vehicle in line with an anchorage strap anchorage point 4 Thread the vehicle seat belt through the BLUE belt path at the front of the restraint and fasten buckle 5 Press the child restraint into the vehicle seat and remove belt slack 6 Attach the anchorage strap to the anchorage point Adjust until all the slack is removed Ensure Base of seat is not lifted STABILISING ARM EARWARD FACING REARWARD FACING BELT PATH BELT PATH Figure 19 NOTE Ensure the harness is pulled through the sale mould amp trim all the way and correctly tensioned Front of vehicle DO NOT LEAVE CHILDREN UNATTENDED IN THE CAR Installation Correct forward facing vehicle position Figure 20 CORRECT USE Figure 21 INCORRECT USE Figure 22 Installation Shoulder height marker forward facing Strap an FORWARD FACING 12 months to 4 years e nex slot NE The shoulder straps must be in the slots which are nearest to the child s shoulders but not Strap cannot more than 25 mm below the chil
18. rs adjuster If indicator is red then take out slack on the belt If indicator is green then your restraint is secure 7 Attach the anchorage strap to the anchorage point Adjust until all the slack is removed Ensure Base of seat is not lifted Forward facing 1 Adjust the child restraint to the forward facing position Fold the Stabilizer Arm if the restraint has been used for rear facing 2 Adjust the base to suit your child as fitment in some vehicles can be impacted due to the location of anchorage points or the shape of rear seats 3 positions base adjustment Place restraint facing forwards on back seat of vehicle in line with an anchorage strap anchorage point 3 Adjust the shoulder straps and headrest to fit your child Refer to page 18 4 Place restraint facing forwards on back seat of vehicle inline with an anchorage strap anchorage point 5 Fasten the lower attachment connectors to the anchor in the vehicle seat located in the vehicle seat bight Repeat for other side of base 6 Pull on the adjuster strap next to the lower connectors and remove slack Repeat for other side of base 7 Check for the green indicator on the lower connectors adjuster If indicator is red then take out slack on the belt If indicator is green then your restraint is secure 8 Attach the anchorage strap to the anchorage point Adjust until all the slack is removed Ensure Base of seat is not lifted Installation Installing lock
19. s of age e Continue to use this child restraint until the child reaches this limit e Do not use forward facing until child s shoulders are above the lower shoulder height marker e Infants are at risk of serious injury if they face forward too early e Children are at risk of serious injury if they move to booster seats too early e Children who have outgrown this restraint are safest in a larger child restraint with an in built harness or a booster seat until their shoulders reach the upper shoulder height marker of the restraint e The child restraint is unsuitable for the occupant when the shoulders are below the lower marker or above the upper marker The child needs to be moved into the next form of child restraint booster seat when they reach the top shoulder height marker NOTE e If the baby s neck muscles are unable to support their head then the child should remain rear facing Vehicle information Location of anchor fitting NOTE e The anchor point can be found in different locations in different cars The illustration above shows possible locations of anchor points Sometimes it is on the parcel shelf in sedans and on the floor area in station wagons vans and hatchbacks Make sure that you do not confuse the luggage hook in the back of a station wagon with anchor points Refer to your owner s manual e An extension strap may be needed for vehicles without a fixed parcel shelf Extension straps and extra
20. ster seat option 3 Larger booster seat To be used with a lap sash seatbelt by a child whose shoulders are above the lower shoulder height marker approximately 4 years of age until the child s shoulders reach the upper shoulder height marker approximately 8 to 10 years of age Can also be used with child harness that is approved for use with this booster seat for more information visit www maxi cosi com au Notes Guarantee Dorel Australia Pty Ltd warrants your new product to be free from defects in materials and workmanship for 6 years on the seat amp 3 years on the trim from the date of purchase provided that the product is used in accordance with accompanying recommendations or instructions where provided The benefit of this warranty is in addition to your rights under the Australian Consumer Law and to other rights and remedies of the consumer under a law in relation to the goods or services to which the warranty relates Dorel Australia Pty Ltd will provide you with your choice of a refund repair or exchange where possible for this product if it becomes defective within the warranty period Dorel Australia Pty Ltd will bear the reasonable expense of claiming the warranty This warranty will no longer apply where the defect is a result of alteration accident misuse abuse or neglect Please retain your receipt as proof of purchase and contact our Cus
21. t has been in a severe crash even if no damage is visible e DO NOT USE THIS RESTRAINT WITHOUT THE COVER e To ensure infant s back is evenly supported do not put more than one nappy on the baby and make sure the nappy is not thickly folded at the back e DO NOT USE A REAR FACING CHILD RESTRAINT WHERE AN AIRBAG IS FITTED IN FRONT OF THE SEATING POSITION e Fit the restraint firmly to the car seat e Fit the harness firmly to the child e A loose restraint or harness is dangerous e Do not harness an infant wrapped in a blanket or swaddled Any blanket or wrap must only be placed over the harness and infant e Seatbelt extenders are not recommended to be used if the seatbelt is not long enough to secure the child restraint If seatbelts are too short then advice should be sought from a child restraint fitter and their recommendation be considered before using a seatbelt extender e Always secure the loose end of the top tether strap Do not use the child restraint where this strap may fall into a split in the seat back or off the side of the seat e Always secure the loose end of the top tether strap to prevent it hanging out of the car or being accessible by the child e ALWAYS ATTACH HOOK AND REMOVE SLACK e THIS RESTRAINT IS NOT SUITABLE FOR USE WHERE THE TOP TETHER STRAP MAY FALL INTO A SPLIT IN THE SEAT BACK OR OFF THE SIDE OF THE SEAT e THIS RESTRAINT MUST BE ATTACHED TO A CHILD RESTRAINT UPPER ANCHORAGE POINT IN THE CAR REF
22. tomer Service team on Ph 1300 809 526 or alternatively via our website at www dorel com au for any difficulties with your product Warranty claims and claims for expense incurred in returning this product can be addressed to our Consumer Service team at 655 685 Somerville Road Sunshine West VIC 3020 Hours 8 30 am to 5 00 pm Monday to Friday For New Zealand please contact Customer Service Centre 14 Sir William Avenue East Tamaki Auckland 2013 Auckland 09 2741040 NZ wide 0800 628 000 Toll Free Hours 8 00 am 5 00 pm Monday to Friday Our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure IMPORTANT KEEP THIS INSTRUCTION MANUAL E IN THE POCKET PROVIDED ON THE HEADREST a mo 3 E o U Australian Standard AS NZS 1754 Lic 1491 SAI Global Europe s most popular and trusted car seat brand DO RE L 2014 Dorel Australia Pty Ltd All Rights Reserved CCA 2013L 015459 08 14
23. uckle 1 Insert one buckle tongue as shown above you will not hear a click 2 Insert the second buckle tongue as illustrated above Now listen for a CLICK 3 Remember to always pull up on the harness straps to make sure buckle is locked tightly Base adjustment PUSH base adjuster in red under front seat and rock seat to adjust the base 3 positions Red base adjuster under front of seat DO NOT LEAVE CHILDREN UNATTENDED IN THE CAR Installation Preparing infant seat to fit your child contd PULL TO LOOSEN Adjusting top tether strap TO LOOSEN Press on the adjuster button with thumb and pull strap back through to loosen anchorage strap using strap which is attached to the seat Figure TO TIGHTEN Adjust anchorage strap and remove slack Pull loose end of strap to tighten Figure NOTE Store the excess webbing in the pocket provide at the back of the child restraint CAUTION CHILDREN CAN BE INJURED OR RESTRAINTS AND TOP TETHER STRAP DAMAGED BY UNSECURED CARGO IN A COLLISION SECURE OR REMOVE HAZARDOUS CARGO BEFORE USING THIS CHILD RESTRAINT Always secure the loose end of the top tether strap to prevent it hanging out of the car or being accessible by the child When not in use fold hanging tether strap and place in storage pocket provided Installation Shoulder height marker rearward facing REARWARD FACING Newborn to 12 months The shoulder straps must be in the Shoulde
Download Pdf Manuals
Related Search