Home

Honeywell Vista-30PSE User Manual

1. Color Lead Terminal On Control These are the same connections as those used for remote GREEN DATA IN terminal 6 keypads BLACK AUX terminal 4 RED AUX terminal 5 YELLOW DATA OUT terminal 7 2 Insert the keyed connector at the other end of the connector cable into the mating header on the Phone module see diagram on next page for location of the header 3 Connect terminals 1 through 5 on the Phone module as shown in the Wiring Table and in the 4285 wiring diagram that follows Use an RJ31X jack with a direct connect cord and make all connections exactly as shown If the leads on the direct connect cord are too short to reach their assigned terminals splice additional wires to them as required 4285 WIRING TABLE 4 Phone Out Ring GRAY lead from direct connect cord Earth ground terminal 21 on control 6 Not Used 7 _ Not Used ees If no touch tones are produced following access to the security system from oh on premises this problem may arise in rare cases it may be necessary to reverse the wires connected to terminals 3 and 4 on the Phone module and the wires connected to terminals 17 amp 18 on the control The wiring diagram shows the wiring connections that will provide proper operation in most cases Caller ID Units If the telephone system on the premises includes a Caller ID unit connect the ID unit directly to the Handset terminals 1
2. 2 Attach the Red and Black wires on the battery connector cable as follows a Red to the positive battery tab on the control board b Black to the negative battery tab on the control board This not required if wires are already connected to the battery tabs on the control 3 Attach the Red and Black wires at the other end of the battery connector cable to the battery as follows a Red to the positive terminal on the battery b Black to the negative terminal on the battery AUXILIARY DEVICE CURRENT DRAW WORKSHEET device mA x of units 4291156615852 Type ES RS aoe Reay unt ES AS 4229 Zone Expander Relay Module 35 100mAt a el Long Range Radio Depends on type of Radio used see its instructions If using hard wire devices such as PIRs refer to the specifications for that particular unit s current draw and include on worksheet Figures are for relays OFF relays ON In UL installations maximum current draw from the Auxiliary Output and the Alarm Output combined must not exceed 600mA 12 2 Section 13 ALPHA DESCRIPTOR PROGRAMMING This section provides instructions for programming Alpha descriptors This is recommended for systems using Alpha keypads and necessary if a 4285 Phone module is used Alpha descriptors cannot be displayed on fixed word keypads If using a 4285 Phone module select from those words in the Alpha Vocabulary list on a following page sho
3. 7 and Security Code 8 Note Whichever entry is used to start stop the action cannot also be used to stop start it The opposite action must either be performed by the other keypad entry or by some other event or operation offered in the programming section If a relay is energized before a 4 wire smoke detector is oh reset the relay will be stopped by the interruption of Aux Power that resets the smoke detector If this is not desired the power to the relay unit should be supplied from another 12V power source e g the same source that is powering ex ternal equipment through the relay contacts Programming Output Relays 1 With at least one 2 line Alpha keypad 5137AD or 6139 connected to the keypad terminals on the control power up the system temporarily If you had previously connected the AC transformer to the control panel you need only plug in the transformer to 120VAC outlet to power up the system 2 Enter the programming mode by keying the following on the Alpha keypad INSTALLER code 4 1 1 1 8 0 A Field 25 OUTPUT MODULE must have been programmed for a 4204 module enter 3 3 Press 80 Note that this is an interactive menu programming mode It is used to program all output relays used in the system 4204 Relay modules Refer to the Programming Form worksheet in the separate PROGRAMMING GUIDE for 80 Interactive Mode Output Relay Displays Upon press
4. Fa You must connect a 4204 relay module when using an AAV unit Do not use relay output number 1 for any other usage Wiring Connections Programming The method used to trigger AAV is via the use of a 4204 relay module as shown in the AAV connection diagrams that follow one diagram for connections when a 4285 Phone module is used the other when the 4285 is not used 1 With at least one 2 line Alpha keypad 5137AD or 6139 connected power up the system If you had previously connected the AC transformer to the control panel you need only plug in the transformer to 120VAC outlet to power up the system 2 Enter the programming mode by keying the following on the Alpha keypad Installer code 4 1 1 1 8 0 3 Press 91 OPTION SELECTION Enter 4 for AAV monitoring Enter 0 for none For UL installations enter 0 no AAV Relay programming in field 80 Do not program anything for Relay 1 Exit the programming mode by keying 99 11 1 o NCOMING TELCO LINE a z DIRECT Zus CONNECT CORD 27 ba A amp oe WW JACK PREMISES g g ANSWERING z Elz MACHINE AND 5 zlo TU PHONES S 5 GE ANSWERING TERMINALS S G Ge E TU MACHINE ON CONTROL 17 18 19 2 21 H EARTH d GROUND H ON o al wl D SE SR 2 g REFER T
5. Check battery Use only batteries specified in the instructions does not apply to transmitters with non replaceable batteries Replace faulty transmitter If system disarmed before ensuing entry time runs out CA or Canceled Alarm will be displayed Sounding will stop If system not disarmed before entry time ends EA or Exit Alarm will be displayed and Exit Alarm message will be sent to central station Sounding will continue until system is disarmed or timeout occurs Clear display by entering code OFF a second time Avoid fault when re arming CONTROL POSSIBLE CAUSE 1 POWER light off or 1a Interrupted AC power supply 1a Check transformer connection and power line circuit breaker NO AC displayed 2 Digital communicator mes 2a Control in TEST mode 2a Remove from TEST mode Sage not being received 2b Telephone connection not secure 2b Check all connections 2c Digital communicator malfunctioning 2c Check with a different VIA 30PSE 2d Telephone number in program needs prefix 2d Program prefix or access code into the or access code control 2e Telephone call to central monitoring station 2e System cannot work in this situation requires operator assistance 3 Does not arm properly 3a READY light not on 3a Check for faulted zone s by pressing Tal make faulted zone s intact or use Bypass arming if desired A VIA 30PSE doesn t respond to Aa CC or MODEM COMM di
6. Zone Types 08 24 Hr Aux 09 Fire 10 Interior w Delay 20 Arm Stay lt 5800 21 Arm Away e RF 22 Disarm Systems 23 No Alarm Only Response When the display shows the zone type you want press to continue You must enter 00 as the zone type for any hard wired zone that is not used Programming Panic Keys 05 Report Code Ist 03 2nd 12 3C Typical summary display Program Alpha 0 No 1 Yes Enter Zn Num 00 Quit 03 Enter next zone number T The report code consists of 2 hexadecimal digits each in turn consisting of 2 numerical digits For example for a report code of 3C enter 0 3 for 3 and 1 2 for C Refer to the SYSTEM COMMUNICATION section for complete information on report codes if necessary Enter the desired report code and then press to continue A summary display will appear showing the data for the zone that was just programmed If it is programmed satisfactorily press to continue The next request is to enter Alpha descriptors for the zones The entry may be done now enter 1 or may be done at a later time using 82 interactive mode enter 0 See the ALPHA DESCRIPTOR PROGRAMMING section for specific procedure If 0 no was entered above the system will return to the Enter Zone Number prompt Proceed with the programming for the next zone Le and zone number When programming zones note t
7. side the loop The EOL resistor must be connected in series with the devices following the last device See the Summary of Connections diagram 3 Connect open circuit devices in parallel across the loop The 1 000 ohm EOLR must be connected across the loop wires at the last device If the EOLR is not at the end of the loop the zone will not be properly supervised and the system may not respond to an open circuit on the zone xh Wiring 4 Wire Smoke Combustion Detectors on Zone 5 The system will support as many 4 wire detectors as can be powered from Auxiliary Power on the control on zone 5 Refer to the detector s instructions for complete details regarding its proper installation and operation 1 Connect 12 volt power for the detectors from Auxiliary Power terminals 4 and 5 which will interrupt power for fire alarm reset Observe proper polarity when connecting detectors See Figure 7 2 Connect detectors including heat detectors if used across terminals of zone 5 All detectors must be wired in parallel 4 Remove 1000 ohm EOL resistor if connected across the zone terminals You must connect the EOL resistor across the loop wires at the last detector 3 To meet NFPA 72 requirements you must use a Supervisory module to supervise power e g System Sensor No A77 716B Relay module TERMINALS O eg EOL POWER SUPERVISION RELAY MODULE A77 716B 4 WIRE SMOKE NEE
8. ADEMCO Security System VIA 30PSE THIS ISSUE INCLUDES THE NEW QED QUICK ENROLLLMENT OF DEVICES PROCEDURE FOR 5800 SERIES TRANSMITTERS Installation Instructions Installation Instructions Installation Instructions N7225V2 4 97 RECOMMENDATIONS FOR PROPER PROTECTION The following recommendations for the location of fire and burglary detection devices help provide proper coverage for the protected premises Recommendations For Smoke And Heat Detectors With regard to the number and placement of smoke heat detectors we subscribe to the recommendations contained in the National Fire Protection Association s NFPA Standard 72 noted below Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and areas of the household as follows For minimum protection a smoke detector should be installed outside of each separate sleeping area and on each additional floor of a multi floor family living unit including basements The installation of smoke detectors in kitchens attics finished or unfinished or in garages is not normally recommended For maximum protection the NFPA recommends that you install heat or smoke detectors in the living room dining room bedroom s kitchen hallway s attic furnace room utility and storage rooms basements and attached garages In addition we recommend the following e Install a smoke detector inside every bedroom where a smoker sleeps e I
9. should be heard on the phone and from a wired keypad and the words DISARMED READY TO ARM or DISARMED NOT READY TO ARM should be heard indicating that the command was entered successfully DISARMED NOT READY TO ARM would indicate an open zone 4 Hang up the phone To Check Phone Module Operation From an Off Premises Phone 1 Have someone dial the premises phone number using a Touch tone phone e If the phone system does not include an answering machine 2 long tones will be heard in the caller s phone followed by a voice prompt HELLO ENTER PHONE CODE NOW The caller should then enter the programmed 2 digit phone code entered in field 26 VOICE PHONE MODULE ACCESS CODE e If the premises phone system includes an answering machine the 2 digit phone code should be entered during a pause at the beginning of or during the outgoing answering machine message 2 When the 2 digit phone code is entered the caller will hear a voice prompt asking for entry of the 4 digit system code ENTER SYSTEM CODE NOW 3 The caller should then enter the INSTALLER code 4111 As a safety feature there is a 3 try limit in which to enter each code phone code and system code after which time the call in will be aborted Also if no keys are pressed for a period of 20 seconds the call in will be aborted 4 Annunciation of a system status report will start if both codes were entered correctly 5 During any pause in the status r
10. 100mA 300mA 500mA 500 ft 152m 250 ft 76m 80 ft 24m 50 ft 15m 750 ft 228 6m 380ft 116m 130 ft 39 6m 80 ft 24m 1300 ft 396m 650 ft 198m 220 ft 67m 130 ft 39 6m 1500 ft 457m 1000 ft 305m 330 ft 100 5m 200 ft 70m Includes Keypads RF Receivers Relay Units or 4285 Phone module unshielded quad conductor cable is used 750 feet if shielded cable is used This restriction is due to the capacitive effect on the data lines when quad cable is used 4 The length of all wire runs must not exceed 1500 feet 457m when 2 Run field wiring from the control to the keypads using standard 4 conductor twisted wire cable using the wire gauge determined in step 1 3 Connect remote Keypads to terminals 4 5 6 and 7 on the control board as shown in Figure 5 KEYPAD CONNECTOR CABLE O RED GREEN KEYPADS S YELLOW CONTROL TERMINALS Figure 5 Keypad Connections To The Control Board Mounting the Keypads 1 Make sure addressable type keypads 4137AD 5137AD 6128 6137 6138 and 6139 are set to non addressable mode address 31 which is the factory default setting Refer to the instructions provided with the keypad for address setting procedure 2 Mount the keypads at a height that is convenient for the user Refer to the instructions provided with the keypad for mounting procedure You can either surface mount or flush mount keypads using an appropriate Trim Ring
11. 1400Hz Under 3 secs The following describes each format in greater detail 3 1 and 4 1 Standard Formats Comprise a 3 or 4 digit subscriber number and a single digit report code e g Alarm Trouble Restore Open Close etc 3 1 and 4 1 Expanded Formats Comprise a 3 or 4 digit subscriber number and a two digit re port code The first digit is displayed on the first line followed by a second line where the first digit is repeated 3 or 4 times and followed by the second digit This is the expanded digit 4 2 Format Comprises a 4 digit subscriber number and 2 digit report code Ademco Contact ID Comprises a 4 digit subscriber number 1 digit event qualifier Reporting Format new or restore 3 digit event code and 3 digit zone number user number or system status number see the following page 15 1 Where Where SSS or SSSS A Z Tt Bb EAc LLg O 3 1 4 1 Report Standard Alarm SSS S A Trouble SSS S T Bypass SSS S B AC Loss SSS S E Low Batt SSS S L Open SSS S O Close SSS S C Test SSS S G Restore SSS S R Alarm AC Restore SSS S R A LoBat Res SSS S RL Trouble Res SSS S RT Bypass Res SSS S Rp Subscriber ID Alarm Code 1st digit Typically Zone Number 2nd digit Trouble Code 1st amp 2nd digits Bypass Code 1st amp 2nd digits AC Loss Code 1st amp 2nd digits Low Battery Code 1st amp 2nd digits Open Code 1st Digit
12. 6 3 Setting the DIP Switches on 5700 Series Wireless Transmitters 0 100eeenereneeee 6 4 Wireless Zone ID Assignments for 5700 Series Transmitters cccceeeeeseeees 6 4 DIP Switch Tables for 5700 RF System Wireless Devices ceteeeeeeeee 6 5 Compatible 5700 Series Transmitters 0 ccccceececeeeeeeeenee ceeeeeceaeeeeaaeseeeeeseeeesae seeeeeeeaees 6 6 Programming the Control For a 5700 Wireless System cccceeeseeeeeeeee ceeeeeneeeesees 6 7 Using the House ID Sniffer Mode 5700 Systems ccceceeseeeeeeeee eerren 6 7 Zone Programming for 5700 Series Transmitters ceeeeeeeeeeeeetaeeeeneeeees 6 7 GO NOGO WEE 6 9 Section 6 Section 7 Section 8 Section 9 Section 10 Section 11 Section 12 WIRELESS RF ZONE EXPANSION 5700 amp 5800 RF SYSTEMS CONT D 5800 Series Transmitter Setup us 6 10 5800 Series Transmitter Input LOOPS cccceeceeeeeeceeee ceeeeeeaeeeeaeeseeeeseeeeesaee ena 6 10 5800 Series Transmitter Input Types cceeeseeeeseceeee ceeeeeeeaeeeeaeeseeeeseeeeetees ena 6 10 Compatible 5800 Series Transmitters ccccccceeeceeeeeee eeeeeeseeeeeseeeseaeeeeeaeeeae eeeeeeeeas 6 11 Programming the RF Transmitters 5800 RF Systems 6 12 Enrolling 5800 Transmitters Into the System 6 13 Enrolling Through Zone Programming 56 6 13 To Either Temporarily or Permanently Remove a Zone From the System D800 System dauere e
13. ENERGY CABLE FOR ALL CONNECTIONS ae i ma Tr z y ZONES 1 4 PRESENT AUX POWER S OUTPUT E 10 5 13 8VDC a lt S00mA MAX T S gt OPTIONAL INTERRUPTS o rae No 5800TM FOR FIRE Z slo TRANSMITTER MODULE ALARM RESET O 6 F 20mA i Clelcis for No 5827BD TO 110VAC NOTE SIE Wireless Bidirectional Keypad UNSWITCHED KEYPAD Q a z lt AND OR OUTLET Gap CURRENT clos No 4285 VOICE MODULE 24HR MUST BE wle s 6 160mA PLUG IN INCLUDED xjl eg TRANSFORMER IN AUX SlSI I No 7720ECP CURRENT S a HS LONG RANGE RADIO 16 5VAC 25VA DRAIN 21dieig MAY ALSO BE CONNECTED e g ADEMCO alc o gt SEE INSTRUCTIONS ACCOM No 1321 CALCULATIONS PANYING THOSE DEVICES 1000 1000 FOR COMPLETE USE No 1321CN OHMS OHMS INFORMATION IN CANADA EOLR EOLR SEE INSTRUCTIONS K Gees ALARM OUTPUT MAXIMUM LOOP RESISTANCE EACH ZONE 300 OHMS PLUS EOLR 10 5 13 8VDC 2A MAX REMOTE KEVPADS RESPONSE ZONES 5 6 300 500MSEC 600mA MAX FOR UL USAGE ZONE 5 CAN BE PROGRAMMED FOR USE AS A FIRE ZONE SYSTEM MUST BE SEE DIAGRAM INCLUDING AUX POWER PROGRAMMED WITH A STEADY FOR BURGLARY PANIC PULS ADEM ING FOR FIRE e g USE CO No 740 SOUNDER No 702 OR 719 SIREN OR 12V BELL CONNECTION OF THE FIRE ALA HEADQUARTERS OR A CENTRA ONLY WITH THE PERMISSION O RM SIGNAL TO A FIRE ALARM L STATION SHALL BE PERMITTED F THE LOCAL AUTHORITY HAVING JURISDICTION THE BURGLAR ALARM SIGNAL SHALL NOT BE CONN
14. This method of exiting may also be done at any time during the review To either temporarily or permanently remove a zone from the system go into programming mode and press 5 6 Enter the zone number and press At the Zone Type prompt enter 0 0 and This sets the type of the zone to Not Used The next prompt will be Delete Zone Yes will permanently remove the zone from the system while No will disable it but retain all data except the original zone type You can then go back to this zone later and put back an active Zone Type to re enable it Check Out Procedure For Hard Wired Zones After installation of all hard wired devices is completed the security system should be checked as follows 1 Make certain that all devices and sensors connected to the hard wired zones are not in a faulted state Doors and windows with contacts should be closed PIRs should be covered use a cloth to mask them temporarily if necessary Plug in the AC Transformer if you have not already done so With all hard wired zones intact the Alpha keypad connected to the system should display amp x DISARMED READY TO ARM If the following is displayed DISARMED Press x to show faults press the key to display the faulted zone s Restore any faulted zone s as necessary also make sure that you have connected a 1000 ohm EOL resistor across the terminals of unused zones When the DISARMED READY TO ARM
15. command the user should make the initial call allow 1 to 3 rings only and hang up Then call in again the Phone Module will now seize the line and 2 long tones will be heard followed by the usual voice prompt for the 2 digit phone access code If this procedure is not followed Phone Module operation will not be possible 5 Zone descriptors should also be programmed regardless of the type of keypads in use If this is not done the Phone module will not annunciate a description of the zone s in alarm trouble etc the Phone module will annunciate zone numbers only You can enter zone descriptors now or later using interactive mode 82 See the ALPHA DESCRIPTOR PROGRAMMING section for a detailed procedure 6 Exit the programming mode by entering 99 Perform a preliminary check of the 4285 Phone module as indicated next Checking the Operation of the 4285 Phone module To Check Phone Module Operation From an On Premises Phone 1 Pick up phone and enter the programmed 2 digit phone code entered in field 26 VOICE PHONE MODULE ACCESS CODE Annunciation of a system status report should automatically start See the User s Guide accompanying the Phone module for detailed information regarding the nature of the status report if necessary 2 During any pause in the status report or immediately following it key the following via the keypad on the phone INSTALLER Code 4111 then press key 1 OFF 3 A beep
16. input Device Type RF Sends periodic check in signals as well as fault Supervised RF restore and low battery signals The transmitter must remain within the receiver s range UR Sends all the signals that the RF type does Unsupervised RF but the control does not supervise the check in signals The transmitter may therefore be carried off premises BR These send only fault signals They do not send Unsupervised Button low battery signals until they are activated The RF transmitter may be carried off premises Do not install batteries in wireless transmitters until ready to use as will be indicated under Programming the RF Transmitters 5800 RF Systems later in this section Though it is not critical to remove batteries after entering into the system it is recommended in order to avoid interference while entering additional transmitters into the system Compatible 5800 Series Transmitters Enter As Input Device Type Description Wireless Panic Has four pushbuttons each with a Transmitter unique input loop code Programmable responses e g Panic Arm Stay Arm Away Disarm etc Pendant BR Only Has single pushbutton Personal Emergency Usually programmed for response Transmitter type of 24 Hr Audible or 24 Hr Silent other zone responses are possible Contains a non replaceable battery At the end of the battery s life the entire unit must be replaced 5802CP Belt Clip BR Only Same as 58
17. press to go to the next screens This is a review mode only and data cannot be changed Example of Output Relay Programming A lamp is to be turned on when any one of 3 specific zones are faulted or when any 24 hour auxiliary zone is disturbed We want to turn off the lamp manually without affecting the arming status of the system In field 80 we choose Output Relay 01 and program the Action A to be 2 Close and stay closed The Event we are looking for to start the relay action is a fault so we will program 2 in EV We will use Zone List 1 for the 3 specific zones so will program 1 in ZL and will program these 3 zones in field 81 s Zone List 1 The second condition for turning on the indicator is triggering a 24 hour aux zone Zone Type 08 so we will program ZT as 08 To stop relay action and turn off the indicator we do not want to use a restore of any zone so we will program a 0 for the Restore of Zone List ZL To choose a manual entry of User Code 7 to turn it off we will program ZT as 34 If no other relay is to be programmed go to field 81 and program the 3 specific zones in Zone List 1 Zone List Displays Zone List No 00 Quit 01 01 Enter Zn Num 00 Quit 00 01 Del Zn List O No 1 Yes 0 01 Delete Zone 0 No 1 Yes 0 01 Zn to Delete 00 Quit 00 Press 81 Zone Lists for Output Relays This interactive mode is applicable only if you ha
18. system armed Improper user operation of exit entry delays Magnets located too far from switches and or doors and windows not properly aligned 18 1 Check or change transmitter s battery Check the control s AC power Check code switches inside transmitter Must match with RF House Code pro grammed in control Move transmitter or 4281 5881 Check for large metal obstructions then relocate transmitter if necessary Verify by activating 4281 5881 with an other similar transmitter If O K now return defective transmitter Verify by making sure other transmitters cannot activate 4281 5881 If defective replace and return original 4281 5881 Verify programming Set DIP switch for address 0 Set field 22 to 1 for 4281 RF receiver or 2 for 5881 RF receiver Set ZT to a valid active zone type in field 56 Install proper battery Check and set the DIP switch Enter unit s serial No in field 56 Check 4281 receiver System battery is low or missing Remote RF keypad battery is low Transmitter for zone nn has a low battery Enter Code OFF to exit TEST mode Enter Code OFF and replace the battery Check the wireless transmitter indicated Restore communication to the RF receiver to cancel the condition Delete input s serial number not the zone and enter the proper loop input see field 56 Determine which transmitter is pro grammed for this zone and r
19. 11 13 The summary screen for the zone will appear Note that an s indicates that a serial number has in fact been enrolled The cursor will be flashing above the loop number Press to accept the zone information Note If you entered 0 in step 10 previously you will not get an indication that the serial number has been enrolled If you want to delete the serial number enter 0 and press The system will then prompt Delete S N Press the 1 Yes key to complete the delete sequence This process deletes the serial number only not the loop number The assumption is that the proper loop number was programmed but the wrong serial or loop number was enrolled To change the loop number you must go back through zone programming for that zone and manually enter the loop number over the existing one 14 If you want to program alpha descriptors now enter 1 Yes See the ALPHA DESCRIPTOR PROGRAMMING section for more information If not enter 0 No This will bring you back to the Enter Zn Num prompt for the next zone When all zones have been programmed enter 00 to quit If you plan to enroll serial numbers in the sequential mode enter 00 to quit then go to Section 14 SEQUENTIAL MODE later in this manual to enroll the serial numbers When you have finished programming all zones including all serial numbers test each zone using the system s TEST mode Do not use the Transmitter ID
20. 3 Press 26 VOICE PHONE MODULE ACCESS CODE If using a 4285 Phone module enter the 2 digit phone access code as follows For first digit enter 1 9 for second digit enter 11 for or 12 for Example if desired access code is 7 7 is the first entry and 11 for is the second entry Enter 00 if not using a Phone module this is the default NOTE a 0 in either digit will disable the phone module 4 Press 95 RING DETECTION COUNT Refer to the chart below and program this field accordingly Voice Answering Module Machine Downloading Field 95 Programming Set for value other than 0 1 14 This will enable the a Ze to answer the phone call Otherwise it will not be possible to access the Phone module Set for a value higher than the number of rings for which the answering machine is set Example if the machine is set for 4 rings use a value of 5 or higher This is recommended so that the Phone module can still be accessed if the answering machine is turned off and does not answer the phone call pes No ves Set for value other than 0 1 14 Enter 15 to bypass the answering machine See Important Note below Important Note If 15 is entered in field 95 to bypass an answering machine and a 4285 Phone Module is included in the installation you should note the following When calling in from an off premises phone to receive a status report or execute a
21. Alpha keypad connected to the system should display DISARMED READY TO ARM If the following is displayed DISARMED Press to show faults press the key to display the faulted zone s Restore any faulted zone s as necessary also make sure that you have connected a 1000 ohm EOL resistor across the terminals of unused expansion zones on the 4219 or 4229 module When the READY TO ARM message is displayed you can proceed to the next step Continued 3 Fault and restore every contact or sensor in each expansion zone individually to ensure that it is being monitored by the system Each time a zone is faulted the keypad should display the number of the faulted zone as programmed by you just previously in 56 mode When each zone is restored the READY TO ARM message should appear again 4 When you get the proper displays on the keypad s the wired expansion zones in the system are functioning properly 5 Unplug the AC transformer If a CHECK 09 message appears on the display data from the control is not being received by the zone expander module Check your wiring and DIP switch settings Section 6 WIRELESS RF ZONE EXPANSION 5700 AND 5800 RF SYSTEMS This section provides the following information e Wireless systems available e Installing the wireless receiver e Installing the 5800TM Module e Programming for the wireless receiver e Setup and installation of the wirele
22. DIP switches on the transmitters must match the system House ID programmed into the control in data field 24 f using a 5827BD wireless keypad the House ID also applies Other than the 5827 and 5827BD 5800 series devices do not communicate by House ID but by transmitting a unique serial number to the control In this case programming a House ID is not necessary Wireless Zone ID Assignments for 5700 Series Transmitters Notes Each wireless zone can be assigned any zone response type such as Entry Exit Interior Follower Perimeter etc see the ZONE RESPONSE TYPE DEFINITIONS section in the separate Programming Guide for a detailed explanations of each zone type For 5700 series transmitters each response type uses a certain range of zone numbers Each range of zone ID numbers is shown below Zone Type Transmitter Zone ID Entry Exit Burg n se 10 through 47 Perimeter Bug 10 through 47 Interior Burg 10 through 47 32 through 47 5775 FIG sise creme tiens 48 through 63 48 through 55 5706 24 Hour Panic 48 through 63 silent or audible 0 0 62 or 63 5701 Day Night Burglary 0 10 through 47 24 Hour Auxiliary 2 00 10 through 47 Zone ID numbers 10 63 can be used but you should note the following in connection with certain transmitter zone IDs identified as follows Transmitter IDs 48 through 55 have h
23. Kit 5137TRK or 6139TRK Refer to the mounting instructions and template included with the keypad and or trim ring kit for specific information Using a Supplementary Power Supply to Power Additional Keypads The control provides 500mA for powering keypads up to a maximum of 4 and other devices from the auxiliary power output The backup battery will supply power to these keypads in the event that AC power is lost When the control s auxiliary power load for all devices exceeds 500mA you can power additional keypads from a regulated 12VDC power supply e g 487 12 supplies 12V 250mA 488 12 supplies 12V 500mA Use a UL Listed battery backed supply for UL installations The 487 12 488 12 power supplies have a backup battery which can power these keypads in the event of AC power loss A Keypads powered from supplies which do not have a backup battery will not function when AC power is lost Therefore be sure to power at least one keypad from the Control s auxiliary power output Connect the additional keypads as shown in Figure 6 using the keypad wire colors shown Be sure to observe the current ratings for the power supply used A Make connections directly to the screw terminals as shown in Figure 6 Make no connection to the keypad blue wire if present Be sure to connect the negative terminal on the Power Supply unit to terminal 4 AUX on the control SUPPLEMENTARY CONTROL POWE
24. No The next prompt will ask you to enter zone number Enter Zn Num 00 Quit Zone Number T Typical summary display J Zone Number Zone Type T Enter the first zone number that you wish to program or 0 0 to exit zone programming H you are starting with zone 5 enter and press to continue If programming another zone enter the desired zone number 06 etc zone 02 is shown in the next display Press to continue A summary display will appear showing the present status of that zone s programming Zn zone number ZT zone type RC report code for that zone In input type of zone Values displayed are currently programmed values If it is programmed satisfactorily press to back up one step and enter the next zone number if desired If you want to change a zone s programming press A prompt for Zone Type will appear Each zone must be assigned a zone type which defines the way in which the system responds to faults in that zone A detailed explanation of each zone type is provided in Response Type Definitions in the ZONE RESPONSE TYPE DEFINITIONS section in the Programming Guide Enter the desired zone type code as listed next The example on the left shows zone type 03 Perimeter entered 00 Zone Not Used 01 Entry Exit 1 02 Not used 03 Perimeter 04 Interior Follower 05 Trouble Day Alarm Night 06 24 Hr Silent 07 24 Hr Audible
25. OFF 1 Bypassing Zones 0 100 Enter code BYPASS 6 zone number s Forced Quick Bypass To automatically bypass all faulted zones use if enabled the Quick Bypass method Enter code BYPASS then wait for all open zones to be displayed Arm when display indicates Bypass and Ready to Arm Chime Mode Enter code CHIME 9 To turn chime off enter code CHIME again SUMMARY OF ARMING MODES Features for Each Arming Mode Arming Exit Entry Perimeter Interior Mode Delay SE AWAY Yes Yes STAY Pre e e INSTANT ve No Ys No MAXIMUM 17 2 Panic Keys 4285 Phone module if used Relay Outputs if used Exit Alarm Displays if programmed There are three individual panic keys or on some keypads panic key pairs If programmed they can be used to manually initiate alarms and send a report to the central station Each key or key pair can be individually programmed for 24 hour Silent Audible Personal or Fire Emergency responses The panic function is activated when both keys of the appropriate key pair are pressed at the same time or the appropriate lettered key is pressed for at least 2 seconds Shown on the left is a typical keypad with individual Panic keys shown lettered ARMED READY OFF AWAY STAY BYPASS 6 CHIME 9 The panic functions are identified by the
26. Programming For 5700 Transmitters Before proceeding each of the 5700 transmitters in the system should have been assigned a unique Zone ID number via its DIP switches and this information marked on the back of the transmitter Wireless Zone ID Assignments for 5700 Series Transmitters on a previous page provides information concerning the assignment of Zone ID numbers to transmitters 1 With a 2 line Alpha keypad connected to the keypad terminals power up the system temporarily If you had previously connected the AC transformer to the control panel you need only plug the transformer in to 120VAC outlet to power up the system 2 Enter the programming mode by keying Installer Code 8 0 Data field 22 RF SYSTEM TYPE must have been programmed for a 5700 RF system 1 Also the House ID should have been entered in field 24 and all 5700 transmitters set to the same House ID 4 Press 56 Zone Programming Mode Use this mode to program zone numbers zone types and alarm report codes for all 5700 wireless zones that are going to be used in the system 5700 transmitters are programmed into the system one at a time starting with the lowest Zone ID number that has been assigned to it previously via its DIP switches Example If the first transmitter to be programmed has been set via its DIP switches to Zone ID 20 you will program zone types and alarm report codes for that transmitter in zone 20 Enter
27. SHOWN UP SE COUNT UP INST MODE UP DIP SWITCH POSITION 8 9 up uP UP UP UP UP UP ur UP UP UP UP UP UP UP UP XMTR ID 48 SHOWN UP UP DIP SWITCH POSITION HOUSE ID 1 SHOWN XMTR ID inm uP uP uP FIXED AT ete UP 1 2 3 4 5 00 UP UP UP 2 Wf e E He 1 DN DN II UU UU SSI ESS J a 5715 5711 5711WM weesen 5716 DOOR WINDOW TRANSMITTER SET SWITCHES WITH UNIVERSAL TRANSMITTER DOOR WINDOW TRANSMITTER BATTERY REMOVED OO DIP j Sw4 TRANSMITTER DIP SWITCH POSITION D TERMINAL TERMINALS DIP e sw3 BLOCK o 6 5 4 3 2 1 snt DONDAN HOUSE ID 1 SHOWN SIDE i SIDE VIEW UP 1 2 1 2 34 5 6 7 8 910112 VIEW sire ESHON a e DI UP ON HOUSE ID 1 SHOWN 6 5 43 2 DN ES SEN 000000 XMTR ID POS 1 UP NORMAL RESPONSE 33 SHOWN POS 12 UP N O SW3 DN FAST RESPONSE N C POS 2 UP NO COVER TAMPER Avoid ID 32 37 with N O DN COVER
28. Swing the base of the board into the mounting clips and secure the board to the cabinet with the accompanying screws see Detail B in Fig 2 2 1 4204 4219 or 4229 1 Insert self tapping screws provided in two adjacent raised cabinet tabs Expansion Unit Leave the heads projecting 1 8 if installed in cabinet 2 Hang the unit on the screw heads via two of the slotted holes at the rear of its housing as shown in Figure 2 3 The expansion unit s cover can be left off if the unit s DIP switch is set with its position 1 ON to the right as shown in its instructions The tampered cover is necessary for installations outside of the control s cabinet LEE LW CIRCUIT f yl DETAIL B SIDE VIEW OF LONG MOUNTING CLIPS DETAIL A SIDE VIEW OF CONTROL CIRCUIT BOARD SUPPORTING SLOTS BOARD Figure 2 Installing The PC Board in the Cabinet Alone or if used with a 4204 4219 or 4229 Module HOLES FOR ANTENNAS AND GROUNDING LUGS Kee SUPPORTING SLOTS eee A RECEIVER CIRCUIT BOARD CIRCUIT SHORT MOUNTING CLIPS CONTROL CIRCUIT BOARD w MOUNTING CLIPS DETAIL B SIDE VIEW OF SHORT MOUNTING CLIPS SCREW ap H aa ANTENNA DETAIL C GROUNDING LUG SIDE VIEW OF LONG MOUNTING CLIPS D DETAIL D ANTENNA AND GROUNDING LUG INSTALLATION RCVR BOARD tee Figure 3 Installing The PC Board And RF Receiver Together In The Cabinet 2 2 Installing the Control and
29. Zn Num 00 Quit 20 Zone 20 entered T JL Zone Number Entry for Zone Type 03 shown A detailed explanation of each zone type is provided in the ZONE RESPONSE TYPE DEFINITIONS section in the separate Programming Guide 5 Enter the zone number that you wish to program As an example zone 20 is shown entered here Zone numbers between 10 and 63 can be assigned to transmitters However the total number of wireless zones that can be used is 8 for 5700 RF systems see Table 1 on a previous page A summary display will appear showing the status of that zone s program If it is programmed satisfactorily press to back up one step and enter another zone number if desired If the zone is not programmed or you want to change it press A prompt for Zone Type will appear Each zone must be assigned a zone type which defines the way in which the system responds to faults in that zone Enter the zone type or change it if necessary Zone types that you can assign are listed below Enter the desired zone type code as listed 00 Zone Not Used 06 24 Hr Silent 01 Entry Exit Burglary 07 24 Hr Audible 03 Perimeter 08 24 Hr Aux 04 Interior Follower 09 Fire 05 Trouble Day Alarm Night 10 Interior w Delay 23 No Alarm Response e g relay activation When the display shows the zone type you want press to continue Enter the report code The report
30. a 5727 5827 or 5827BD wireless keypad has a low battery it will be displayed as Zone 00 when it transmits Note After a low or dead battery is replaced activate the transmitter and then enter the security code OFF to clear the system s memory of the Low Battery signal e Batteries in the wireless transmitters may last from 4 7 years depending on the environment usage and the specific wireless device being used External factors such as humidity high or low temperatures as well as large swings in temperature may all reduce the actual battery life in a given installation The wireless system can identify a true low battery situation thus allowing the dealer or user of the system time to arrange a change of battery and maintain protection for that given point within the system e Some transmitters eg 5802 5802CP and 5803 contain long life but non replaceable batteries At the end of their life the complete unit must be replaced and a new serial number entered into the control e Button type transmitters eg 5802 5802CP 5803 5804 should be periodically tested by the user for battery life Receiver Supervision Wireless System Installation Advisories The receiver itself is supervised A tamper report zone 9 will be generated a If communication with the receiver is interrupted or b If valid RF signals are not received within 12 hours from at least one supervised wireless transmitter if any are included in
31. alarm sounder and audible low battery warning 5711 Slimline Door Window Transmitter Can be used with any closed or open circuit sensor 5715WH Universal Transmitter DIP switch selectable for fast res ponse and open or closed sensor usage Has a tamper protected cover 5716 5716WM Door Window Transmitter Can be used with any open or closed circuit sensor Features a built in reed switch 5716WM includes magnet Audio Discriminator For use in unoccupied areas to detect the sound of shattering glass when a window is broken Dual Technology Glassbreak Detector Detects the sound and shock of breaking glass and requires the presence of both to initiate an alarm condition PIR Detector Wireless Keypad House ID Dual element passive infrared detector with built in selectable pulse count Note There is a 3 minute lock out between fault transmissions to con serve battery life Can be used to turn the burglary protection on and off Features the same built in panic functions as wired keypads Identified as zone 00 on wired keypads when it transmits with a low battery 5827BD Wireless Keypad House ID usable in a 5700 System Requires use of 5800TM Module RF House ID must be programmed in field 24 and the wireless key pad set to the same ID Operates the system similarly to wired keypads Can indicate system status via its 3 LEDs and sounder Includes 3
32. and zone 09 will be displayed if a module is disconnected from the control s keypad terminals 4 5 6 amp 7 4204 RELAY 4 TYPICAL DIP SWITCH SHOWN OFF FOR SETTING DEVICE ADDRESS AND ENABLING DISABLING TAMPER ODDA 56 RELAY COVER TAMPER REED SWITCH 4 PIN CONSOLE PLUG EITHER OR BOTH CAN BE USED TB1 6d 9 OOO DATA IN FROM CONTROL GROUND DATA OUT TO CONTROL 12V Figure 10 4204 Connections to Control RELAY RELAY DIP SWITCH 4229 CONNECTOR 7 2 FOR SETTING ADDRESS AND ZONE A RESPONSE O O DD EITHER OR BOTH CAN BE USED TERMINALS ON ho RELAY SC CONTROL PANEL TB2 O NO C NC 4 PIN CONSOLE PLUG Lo GRN DATA OUT TAMPER JUMPER POSITION a TO CONTROL EF TERM 6 Lo 4229 IN CABINET E gt LL lolz NOT TAMPERED o GROUND TERM4 Jio Sn ac amp 4229 REMOTE TERM ll ll ae o TAMPER PROTECTED ge ole ey RE ae S YEL DATA IN 22 o gt TERM7 aos o CONTROL BLY GC REED TERMINATE EACH Bee TAMPER WITH 1000 OHM 1K RELAYS SWITCH END OF LINE RESISTOR gt EACH ZONE S MAX LOOP RESISTANCE 300 OHMS E O L ZONES A B C D E F G H Figure 11 4229 Connections to Control Programming Options Defined The following will help you understand the programming of OUTPUT RELAYS when using 80 and
33. as the 5816 and 5817 can support more than one zone referred to as loops or inputs On the 5816 for example the wire con nection terminal block is loop 1 the reed contact is loop 2 Each loop must be assigned a different zone number and entered separately For button transmitters wireless keys such as the 5804 you must assign a unique zone number to each individual button used on the transmitter Each button on the transmitter also has a pre designated loop or input number which is displayed when entered Refer to 5800 Series Transmitter Input Loop Identification in the separate Programming Guide manual UL The 5816 and 5817 do not supervise their loop wiring for shorts Therefore for UL Household Burglary installations the loop wiring may not exceed 3 ft Programming an RF House ID 01 31 in field x24 is necessary only if using 5827 or 5827BD wireless keypads An RF House ID is not necessary for other 5800 series transmitters and the entry should be left at 00 default in those cases 5800 Series Transmitter Input Types The 5827 wireless keypad reports low battery status as zone 00 All of the transmitters described have one or more unique factory assigned loop inputs Each of the inputs requires its own programming zone e g a 5803 s three button inputs require three programming zones 5800 Transmitters can be entered into the system as one of the following input device types
34. completed key 0 0 at the Enter Zone Number prompt 14 Exit the programming mode by keying 99 e In field 56 at the summary line for each zone the entered values can be checked f you wish to change anything press to move to the previous entry Press a number of times to move to earlier entries Press to move to later entries again e Zone entries can be reviewed by pressing 5 6 Changes cannot be made here so this is safer for review Enter the first zone number to be viewed and press To view each zone press and the zone number will advance to the next programmed zone When the end of the list is reached press 0 0 to exit This method of exiting may also be done at any time during the review e To either temporarily or permanently remove a zone from the system go into programming mode and press 5 6 Enter the zone number and press At the Zone Type prompt enter 0 0 and This sets the type of the zone to Not Used The next prompt will be Delete Zone Yes will permanently remove the zone from the system while No will disable it but retain all data except the original zone type You can then go back to this zone later and put back an active Zone Type to re enable it Before mounting transmitters permanently conduct Go No Go tests to verify adequate signal strength and reorient or relocate transmitters if necessary During this mode wireless receiver gain is reduced b
35. e 026 BUILDING 083 FOYER 131 MOTION 179 SOUTH Bag c 084 FREEZER 132 MOTOR 180 SPRINKLER 232 app 028 CABINET 085 FRONT N 182 STATION ge a 029 CALL G 134 NORTH 184 STORE 234 4TH 030 CAMERA 089 GARAGE 135 NURSERY 185 STORAGE RE 031 CAR 090 GAS o 186 STORY e 236 5TH 033 CASH 091 GATE e 136 OFFICE 190 SUPERVISED 337 6 034 CCTV 092 GLASS 138 OPEN 191 SUPERVISION 238 6TH 035 CEILING 093 GUEST 139 OPENING 192 SWIMMING 239 7 036 CELLAR 094 GUN 140 OUTSIDE 193 SWITCH 240 7TH 037 CENTRAL H 142 OVERHEAD S EE 241 8 038 CIRCUIT k P 242 8TH e 040 CLOSED i ee HEAT 143 PAINTING 196 TELCO 243 9 046 COMPUTER 098 HOLDUP 144 PANIC 197 TELEPHONE 244 9TH 047 CONTACT 099 HOUSE 145 PASSIVE 199 TEMPERATURE D 100 INFRARED 146 PATIO SC E e 048 DAUGHTERS e 101 INSIDE 147 PERIMETER 049 DELAYED i We 148 PHONE 202 TRANSMITTER 250 Custom Word 1 e 050 DEN 103 INTRUSION 150 POINT U 251 Custom Word 2 051 DESK J 151 POLICE 205 UP 052 DETECTOR 104 JEWELRY 152 POOL 206 UPPER 252 Custom Word 3 e 053 DINING 153 POWER 207 UPSTAIRS 054 DISCRIMINATOR K R 208 UTILITY 253 Custom Word 4 055 DISPLAY 105 KITCHEN 155 RADIO BBE ee Wee 156 REAR Note Bulleted words in boldface type are those that are also available for use by the 4285 Phone Module If using a Phone module and words other than these are selected for Alpha descriptors the module will not provide annunciation of those words CHARACTER A
36. is not displayed on any of the keypads in the system or a Not Ready message is displayed check the keypad wiring connections and make sure each of the 6 basic hard wired zones has a 1000 ohm resistor connected across its terminals 4 When you get the proper Ready displays on the keypad s the system is functioning properly at this point Do not remove the EOL resistors until you are ready to make connections to the hard wired zones to allow for testing later in the manual S If an OC or OPEN CIRCUIT display is present on the keypad data from the control is not reaching the keypad Check the wiring Section 4 BASIC HARD WIRED ZONES 5 AND 6 This section provides general information for the hard wired zones in the system plus specific instructions for installing 4 wire smoke combustion detectors Also included is a procedure for programming the hard wired zones Installing the Hard Wired Zones Common Characteristics for Zones 5 and 6 e Response time from 300 500 milliseconds 400 milliseconds nominal e OLR supervised zones support both open circuit amp closed circuit devices e As many 4 wire smoke detectors as can be powered from Aux Power on the control on zone 5 Wiring Burglary and Panic Devices To Zones 5 and 6 1 Connect sensors contacts to the hard wired zone terminals 8 through 16 See the Summary of Connections diagram 2 Connect closed circuit devices in series in the high
37. keypad sound continuously but stop when the system is disarmed No message will be transmitted to the central station e A display of EXIT ALARM or EA and a zone indication will appear if an exit or interior zone contained a fault during closing at the time the exit delay ended but the system was NOT disarmed during the entry delay time The alarm sounder and keypad sound continuously until the system is disarmed or timeout occurs An exit alarm message is sent to the central station Continued 17 3 e The EXIT ALARM display etc will also result if an alarm from an exit or interior zone occurs within two minutes after the end of an exit delay In any of the previous cases use a second OFF sequence code plus OFF key to clear the display Trouble Conditions See Troubleshooting Guide also General Information Check and Battery Displays Power Failure Other Displays Fixed Word displays are in parentheses The word CHECK on the keypad s display accompanied by a rapid beeping at the keypad indicates that there is a trouble condition in the system The audible warning sound can be silenced by pressing any key Instruct users to call for service immediately upon seeing any of the following messages e A display of CHECK and one or more zone numbers indicates that a problem exists with the displayed zone s and requires attention e A display of CHECK and 09 indicates that communication betwee
38. message is displayed you can proceed to the next step Fault and then restore every contact or sensor on each zone individually to ensure that it is being monitored by the system Each time a zone is faulted the keypad should display the number of the faulted zone When each zone is restored the READY TO ARM message should appear again When you get the proper displays on the keypad s the hard wired zones in the system are functioning properly Section 5 WIRED ZONE EXPANSION This section provides information regarding the use of expansion modules 4219 or 4229 for expanding the number of wired zones in the system describes the modules that can be used and their wiring connections plus a procedure for programming the wired expansion zones Installing Zone Expansion Units You can add an additional 8 wired expansion EOLR zones to the basic control s 8 hardwired zones for a total of 14 wired zones by using a No 4219 Wired Expansion Unit or 4229 Wired Expansion Relay Unit Location e You can mount an expansion unit within the control cabinet if space permits Otherwise mount the unit outside the cabinet Supervision e Units are supervised against removal Keypads will display CHECK and zone 09 if a zone expander is disconnected e Units have tamper protection for security when mounted outside of the cabinet Zone Information Assign zone numbers 10 17 for the eight wired expansion loops designated A to H You ca
39. of control board along with any documentation that came with the product Note your ADEMCO customer number and or company name Having this information handy will make it easier for us to serve you quickly and effectively You may contact Technical Support via Toll Free FAX Please include your return FAX number You will receive a reply within 24 hours You may also contact Technical Support via modem to ATLIS BBS Technical Support s Electronic Bulletin Board System Replies are posted within 24 hours East Coast Technical Support 1 800 645 7492 8 a m 6 p m E S T West Coast Technical Support 1 800 458 9469 8 a m 5 p m P S T Technical Support FAX Number 1 800 447 5086 ATLIS BBS Electronic Bulletin Board System 1 516 496 3980 1200 9600 Baud 8 Data Bits 1 Start Stop Bit No Parity ATLIS FAX Automated Fax Retrieval System 1 800 573 0153 1 516 921 6704 Ext 1667 ADEMCO World Wide Web Page HTTP WWW ADEMCO COM INTERNET E Mail Address Ademco_ Tech SPRT Ademco 165 Ademco com 18 3 18 4 Section 19 SPECIFICATIONS amp ACCESSORIES Specifications VIA 30PSE 1 Physical 12 1 2 W x 14 1 2 H x 3 D 318mm x 368mm x 76mm SECURITY CONTROL 2 Electrical VOLTAGE INPUT 16 5VAC from plug in 25VA transformer Ademco No 1321 TF2 in U S A RECHARGEABLE BACK UP BATTERY 12VDC 4AH Gel type Charging Voltage 13 8VDC ALARM SOUNDER 12V 2 0 Amp output can drive 12V BELLS or can dr
40. on battery power only Note There is a random delay up to 48 minutes before the system will report an AC failure to the central station The keypad response is about 6 seconds The restore report has a random delay of up to 12 minutes if the AC failure report was sent e If the battery standby capacity is used up during a prolonged AC power outage the control s auxiliary power will shut down to minimize deep discharge of the battery Busy Standby dl If this remains displayed for more than 1 minute the system is disabled Modem Comm CC The system is in communication with the central station for change of function or status verification Comm Failure FC A communication failure has occurred Open Circuit OC The keypad is not receiving signals from the control and sees an open circuit Long Rng Trbl bF Back up LRR communication failure 17 4 Section 18 TROUBLESHOOTING GUIDE SYSTEM including Wireless SYMPTOM POSSIBLE CAUSE REMEDY Transmitter signal not received at 4281 5881 Transmitter zone number appears during Go NoGo test mode but does not clear Low Battery message on keypad Periodic beep s from keypad With 5800 RF System no response to a transmitter in normal operation although zone number clears during Go NoGo mode Nuisance or phantom alarm Intrusion alarm for no ap parent reason Transmitter or 4281 5881 not properly pow ered If Transmitter is 5827 5827BD hous
41. on premises or off premises phones for arming disarming etc plus control of relay outputs Optional Long Range Radio e Allows all messages that have been programmed to go to the primary telephone number to be reported additionally to a 7720 PLUS or 7820 radio Alarm Output Provides a 12VDC 2 AMP output that can drive the compatible sounders listed in the EXTERNAL SOUNDERS section assumes a fully charged battery is connected e Steady output for Burglary Panic or temporal pulse sounding output for Fire notification as required by UL e Uses current limiting circuitry for protection Auxiliary Power Output Provides 12VDC 500mA maximum Uses current limiting circuitry for protection e Output interrupts for smoke detector reset if 4 wire smoke detectors are used Programming e Programmed options are stored in electrically erasable non volatile EEROM memory information can be reprogrammed at any time and will not be lost in the event of a power loss e The system can be uploaded downloaded or controlled via an IBM compatible computer using either Ademco s V Link downloading software Rev 4 or higher or Ademco s Compass Windows downloading software and a modem specified by Ademco Keypad programming consists of e Data field programming e Interactive menu mode programming For programming from a keypad a 5137AD or 6139 2 line Alpha keypad must DA be connected but need not necessarily stay in the syste
42. panic keys Magnets Package of 8 magnets for use with 5716 transmitters The 5711 5715 and 5716 do not supervise their loop wiring for shorts Therefore for UL Household Burglary installations the loop wiring may not exceed 3 feet Programming the Control For a 5700 Wireless System 1 With at least one two line Alpha keypad wired and set to address 31 default power up the system temporarily by plugging the AC transformer previously wired to the control into a 120VAC outlet 2 Enter data field programming mode Installer Code 8 0 Set data field 22 RF SYSTEM TYPE to 1 5700 4 Enter the House ID 01 31 in data field 24 RF HOUSE ID CODE The House ID entered in this field will identify 5700 series transmitters in a 5700 RF system all 5700 type transmitters are set for the same House ID If a 5827BD wireless keypad is to be used in a 5700 RF system the same House ID code entered in this field must also set on the 5827BD wireless keypad s 5 Exit the programing mode by keying 99 CA The DIP switches in each 5700 series transmitter that is going to be used in the system must be set to the appropriate zone ID number and House ID Refer to Setting the DIP Switches On 5700 Series Transmitters and Wireless Zone ID Assignments for 5700 Series Transmitters on a previous page if necessary The system House ID must have been programmed in data field 24 and the DIP switches o
43. provide reasonable protection against such interference in a residential installation However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures If using an indoor antenna have a quality outdoor antenna installed Reorient the receiving antenna until interference is reduced or eliminated Move the radio or television receiver away from the receiver control Move the antenna leads away from any wire runs to the receiver control Plug the receiver control into a different outlet so that it and the radio or television receiver are on different branch circuits If necessary the user should consult the dealer or an experienced radio television technician for additional suggestions The user or installer may find the following booklet prepared by the Federal Communications Commission helpful Interference Handbook This booklet is available from the U S Government Printing Office Washington DC 20402 The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User s Manual Unauthorized changes or modifications could void the user s authority to operate the equipment FEDERAL COMMUNICATIONS COMMISSION FCC Part 68 STA
44. that the connected keypads are functioning properly in the system Keypads That May Be Used e Fixed Word Display 4127 4137AD 6127 6128 6137 e Alpha Display 5137AD 6138 6139 e Up to 4 keypads independent of auxiliary power considerations you may need to use an auxiliary power supply if the 500mA aux output is exceeded A If you are going to use a 4285 Phone module you MUST use addressable keypads 4137AD 5137AD 6128 6137 6138 6139 in the system but set to the non addressable mode address 31 Wiring To The Keypads 1 Determine wire gauge by referring to the wiring length gauge chart below For devices Keypads RF Receivers etc connected to a single 4 wire run determine the current drawn by all units connected to the single wire run then refer to the Wiring Run chart to determine the maximum wire length that can be safely used for each wire size Current draw for all devices can be found in the SPECIFICATIONS AND ACCESSORIES section Note Refer to Auxiliary Device Current Draw Worksheet in the FINAL POWER UP section for current draw for all keypads Maximum wire lengths for any device that is homerun to the control can also gh be determined from the chart based on the current draw of that device alone Wiring Run Chart For Devices Drawing Aux Power From The Control 12V amp 12V a TOTAL CURRENT DRAWN BY ALL DEVICES CONNECTED TO A SINGLE WIRE RUN Wire Size 50mAorless
45. the system Disregard the following advisories if the receiver is mounted in the control cabinet as described in the INSTALLING THE CONTROL section 1 Place the receiver in a high centrally located area for best reception Do not place receiver on or near metal objects This will decrease the range and or block transmissions Do not mount receivers or transmitters in an attic where extreme temperatures could prevent proper operation 2 The house IDs must be entered for the receiver applies only to 5700 RF system or if using a 5827 5827BD wireless keypad in a 5700 or 5800 RF system Installation and Setup of the 4281 5881 Wireless Receivers 1 Mount the receiver s if not installed previously in the control cabinet as indicated in the INSTALLING THE CONTROL section Receivers can detect signals from transmitters within a nominal range of 200 feet Take this into consideration when determining mounting location outside of the cabinet 2 Make sure that the receiver s DIP switches are set for device address 0 as shown in Figure 8 all switches to the right OFF 3 Connect the receiver s wire harness to the control s keypad terminals 4 5 6 and 7 Plug the connector at the other end of the harness into the receiver see Figure 9 4 Refer to the receiver s installation instructions for further installation instructions regarding antenna mounting etc NOTE WHEN CIRCUIT BOARD IS MOUNTED IN CONTROL S CABINET GROU
46. transmitter to be enrolled before pressing the upper left hand button of the program tool Press the button and then immediately activate the transmitter to be enrolled This will minimize the possibility of the system accepting a random transmission instead of one from the intended transmitter Enter Zn Num 00 Quit 15 8 After all wireless zones have been displayed whether enrolled or not the Enter Zn Num prompt will appear Enter 00 to exit the Sequential mode and return to the data field programming mode When you have finished programming all zones test each using the system s TEST mode see TESTING THE SYSTEM section Do not use the Transmitter ID Sniffer mode for testing as it will only check for transmission of one zone on a particular transmitter and NOT the zones assigned to each additional loop 14 3 14 4 Section 15 SYSTEM COMMUNICATION This section provides an explanation of formats this system accommodates for reporting alarms and other system conditions to the central station The process of a successful transmission consists of both the method of communication between the control panel and the central station receiver and the actual way the information is sent and displayed at the central station Report Code Formats When the panel calls the central station receiver it waits to hear a handshake frequency from the receiver to confirm that the receiver is on line and ready to recei
47. will not display the serial number but will wait for a transmission from another transmitter or transmitter loop input 10 Confirmed A022 4064 1 12 The system will then enter a confirmation mode so that the operation of the actual programmed input can be confirmed Activate the loop input or button that corresponds to this zone We recommend that you confirm the programming of every transmitter before proceeding to the next zone When the system sees activity on the appropriate input it will beep three times and display the confirmation message A At any time during this step you may press the key on the keypad or the upper left hand button of the program tool if you are satisfied with the serial and loop number combination that has been enrolled regardless of whether or not the enrolled input has been confirmed If the incorrect transmitter has been enrolled press the key on the keypad or the upper right hand button of the program tool to delete the serial number and return to the Learn S N prompt A single long beep will be heard from the keypad to verify pressing of the upper right hand button Then press 1 Yes or press the upper left hand button of the program tool a single short beep will verify the system is ready for enrolling and re activate the proper transmitter or transmitter loop input ZN ZT RC IN L 10 03 00 RF 1s Program Alpha O NO 1 YES 0 Enter Zn Num 00 QUIT
48. with the same letter as it does 13 4 ALPHA VOCABULARY LIST For Entering Zone Descriptors NOTE Some rarely used words appearing in previously published lists have been deleted from the list below Use only this list for selecting zone descriptors 000 Word Space 057 DOOR L R Vv A 059 DOWN 106 LAUNDRY 155 RADIO 209 VALVE e 001 AIR 060 DOWNSTAIRS 107 LEFT 156 REAR 210 VAULT 002 ALARM 061 DRAWER 108 LEVEL 157 RECREATION 212 VOLTAGE 004 ALLEY 062 DRIVEWAY 109 LIBRARY 159 REFRIGERATION w 005 AMBUSH 064 DUCT 110 LIGHT 160 RF 213 WALL 006 AREA E 111 LINE 161 RIGHT 214 WAREHOUSE 007 APARTMENT 065 EAST 113 LIVING 162 ROOM 216 WEST 009 ATTIC 066 ELECTRIC e 114 LOADING 163 ROOF 217 WINDOW 010 AUDIO 067 EMERGENCY 115 LOCK e 219 WING B 068 ENTRY 116 LOOP 164 SAFE 220 WIRELESS 012 BABY 069 EQUIPMENT 117 LOW 165 SCREEN x 013 BACK 071 EXIT e 118 LOWER 166 SENSOR 222 XMITTER 014 BAR 072 EXTERIOR M 167 SERVICE y 016 BASEMENT F 119 MACHINE 168 SHED 223 YARD 017 BATHROOM 073 FACTORY 121 MAIDS 169 SHOCK 7 018 BED 075 FAMILY 122 MAIN 170 SHOP 224 ZONE N e 019 BEDROOM 076 FATHERS 123 MASTER 171 SHORT 225 See o 020 BELL 077 FENCE 125 MEDICAL 173 SIDE 226 0 e 021 BLOWER 079 FIRE 126 MEDICINE 174 SKYLIGHT 8 Se 4 e 022 BOILER 080 FLOOR 128 MONEY 175 SLIDING 228 1ST 023 BOTTOM 081 FLOW 129 MONITOR 176 SMOKE 220 a 025 BREAK 082 FOIL e 130 MOTHERS 178 SONS 230 2ND
49. 02 Personal Emergency Miniature e Has single pushbutton Personal Emergency e Usually programmed for a response Transmitter type of 24 Hr Audible or 24 Hr Silent other zone responses are possible 5804 Wireless Key BR Only e Has four pushbuttons each with a Transmitter unique input loop code e Programmable responses eg Arm Stay Arm Away Disarm etc 5806 Wireless Photoelectric e One piece smoke detectors with a 5807 Smoke Detectors built in transmitter Wireless Photoelectric RF e One piece smoke detectors with a Smoke Detector built in transmitter e Has built in thermal circuitry to detect temperatures above 135 F and tamper switch on base Door Window e Has two unique input loop codes Transmitter one for a wired closed circuit contact loop the other for a built in reed switch used in conjunction with a magnet 5816 Low Temperature e Transmits a fault condition when TEMP Sensor temperature drops below 45 F 5817 Multi Point e Has three unique input loop Universal Transmitter codes one for a Primary contact loop with programmable options the others for two Auxiliary closed circuit contact loops U L The 5816 and 5817 do not supervise their loop wiring for shorts Therefore for UL Household Burglary installations the loop wiring may not exceed 3 feet Continued Compatible 5800 Series Transmitters Continued Enter As Input Device Type Description RF Shock Proces
50. 03 AW Note that AW indicates an auxiliary wired zone expansion module zone If it is programmed satisfactorily press to display the next prompt P Albha For all zone types the next request is to enter rogram pie Alpha descriptors for the zones The entry may 0 No 1 Yes 0 be done now enter 1 or may be done at a later time using 82 interactive menu mode enter 0 We recommend that the entry of Alpha descriptors be done later using 82 menu mode See ALPHA DESCRIPTION PROGRAMMING section for specific procedure If 0 No was entered above the system will Enter Zn Num display a prompt for entry of the next wired 00 Quit 11 expansion zone number Proceed with the programming for the next zone as indicated Enter next zone number previously When all wired expansion zones are programmed satisfactorily exit 56 mode at the Enter Zn Num prompt by pressing 0 0 Exit the programming mode by keying 99 Proceed to the check out procedure that follows Check Out Procedure For Wired Expansion Zones After you have completed installation of all devices all wired expansion zones should be checked as follows 1 Make certain that all devices and sensors connected to the wired expansion zones are not in a faulted state Doors and windows with contacts should be closed PIRs should be covered use a cloth to mask them temporarily if necessary 2 With all zones intact including hard wired zones the
51. 1100mA current draw Ademco 705 820 20 watt 8 ohm indoor or outdoor speaker 5 inch Round Speaker Requires a driver Ademco 713 Speaker 40 watt 8 ohm indoor outdoor speaker Requires a driver System Sensor PA400B Indoor piezo sounder red or beige rated at 90 beige PA400R red dB 10 feet Indoor Piezo Sounder Requires special power wiring connections 19 3 Compatible 4 Wire Smoke Combustion Detectors System Sensor Models 1412 4 wire ionization products of combustion detector 2412 4 wire photoelectric smoke detector 2412TH 4 wire photoelectric smoke detector w 135 F 57 C heat detector A77 716B EOL relay module supervisory module for wired 4 wire fire zone 2112 24T Low profile 4 wire photoelectric smoke detector w 135 F 57 C heat detector 19 4 APPENDIX A REGULATORY AGENCY STATEMENTS FEDERAL COMMUNICATIONS COMMISSION FCC Part 15 STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use The FCC requires the following statement for your information This equipment generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio and television reception It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules which are designed to
52. 7 amp 18 on the control as shown in 4285 Phone module Wiring Connections diagram that follows 4285 WIRING NOTES Wire the 4285 Phone module exactly as shown using a direct connect cord and RJ31X jack If Touch tones are not heard when pressing keys following phone access to the security system via an on premises phone try reversing the pair of wires connected to terminals 3 amp 4 on the 4285 and the pair of wires connected to terminals 17 amp 18 on the control H an error signal fast busy signal is heard when trying to access the system via the phone check for correct line seizure wiring as described in note 4 Connection to the incoming Telco line via a RJ31X jack and direct connect cord as shown in this diagram is essential even if the system is not connected to a central station The 4285 will not function if this is not done The house phone lines gray and brown wires must be wired to the Phone module terminals not to the control terminals Otherwise an error signal fast busy signal will occur when trying to access the system from an on premises phone If the telephone system on the premises includes a Caller ID unit connect the ID unit directly to the Handset terminals 17 amp 18 on the control as shown Incoming Handset Telco Line TERMINALS ON CONTROL EARTH GROUND COLD WATER PIPE oe INCOMING TELCO LINE CALLER ID AO Ba P E 0Z DIRECT IMPORTA
53. 81 interactive menu modes The options used to start and stop relays are described below followed by the actual screen prompts and available entries The letter s in parentheses after each function described below such as A after ACTION are those that appear in the various summary displays of programmed data during programming ACTION A The ACTION of the relay is how the relay will respond when it is activated by the START programming You may want the relay to activate momentarily to pulse on and off continuously or to remain activated until some other event occurs to stop it There are four different choices of actions e ACTIVATE for 2 SECONDS and then reset e ACTIVATE and REMAIN ACTIVATED until stopped by some other event e PULSE ON and OFF until stopped by some other event e NOT USED when the relay is not used START STT The START programming determines when and under what conditions the relay will be activated The following START options are available A 1 EVENT EV is the condition Alarm Fault Trouble that must occur to a zone or group of zones zone list in order to activate the relay These conditions apply only when a zone list is used The different choices for EVENT are listed below and in the Programming Output Relays section that follows e ALARM Relay action begins upon any alarm in an assigned zone in the zone list e FAULT Relay action begins upon any opening or short in an assi
54. CRIPTION ON THE FACE HEREOF IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY EXPRESS OR IMPLIED OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER S OWN NEGLIGENCE OR FAULT Seller does not represent that the products it sells may not be compromised or circumvented that the products will prevent any personal injury or property loss by burglary robbery fire or otherwise or that the products will in all cases provide adequate warning or protection Customer understands that a properly installed and maintained alarm may only reduce the risk of a burglary robbery fire or other events occurring without providing an alarm but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result CONSEQUENTLY SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING HOWEVER IF SELLER IS HELD LIABLE WHETHER DIRECTLY OR INDIRECTLY FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE REGARDLESS OF CAUSE OR ORIGIN SELLER S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER This warranty replaces any previous warranties and is the only warranty made by Seller on this prod
55. ECTED TO A POLICE EMERGENCY NUMBER No 5137AD OR 6139 IT NEED NOT REMAIN IN SYSTEM AFTER PROGRAMMING THE SYSTEM CAN USE No 4127 20mA 4137AD 60mA 5137AD 90mA 6127 20mA 6128 30mA 6137 85mA 6138 100mA OR 6139 100mA MULTIPLE KEYPADS MAY BE THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND 2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION COMPLIES WITH FCC RULES PART 68 FCC REGISTRATION NO AC398U 68192 AL E RINGER EQUIVALENCE 0 7B USED BUT USE MAX OF 220 FT OF 22 WIRE OR 550 FT OF 18 LOCATED AT TIP RING TIP RING SE BROWN GRAY GREEN RED pean HANDSET INCOMING PHONE LINE TELEPHONE WIRING VIA RJ31X JACK DIRECT Geer CONNECT CORD IN CANADA CA38A JACK ere INSTRUCTIONS OR DOC LOAD NO 3 PROPER GROUNDING WARNING TO PREVENT RISK OF SHOCK DISCONNECT TELEPHONE LINE AT TELCO JACK BEFORE SERVICING THIS UNIT THIS EQUIPMENT SHOULD BE INSTALLED IN ACCORDANCE WITH THE NATIONAL FIRE PROTECTION ASSOCIATION S STANDARD 74 NATIONAL FIRE PROTECTION ASSOC BATTERYMARCH PARK QUINCY MA 02269 PRINTED INFORMATION DESCRIBING PROPER INSTALLATION OPERATION TESTING MAINTENANCE EVACUATION PLANNING AND REPAIR SERVICE IS TO BE PROVIDED WITH THIS EQUIPMENT WARNING OWNER S IN
56. FOR ZONE TYPES 00 Not Used 05 Trouble Day Alarm Night 08 24 Hr Aux 01 Entry Exit 06 24 Hr Silent 09 Fire 03 Perimeter 07 24 Hr Audible 10 Interior w Delay 04 Interior Follower CHOICES FOR SYSTEM OPERATION 20 Arming Stay 33 Any Burglary Alarm 39 Any Fire Alarm 21 Arming Away 34 Code 7 Key Entry 40 Bypassing 22 Disarming Code OFF 35 Code 8 Key Entry 41 AC Power Failure 31 End of Exit Time 36 At Bell Timeout 42 System Batt Low 32 Start of Entry Time 38 Chime 58 Duress Or at Disarming whichever occurs earlier If a zone list will be used to STOP or restore the relay action enter the zone list ZL number 1 2 or 3 to be programmed in 81 mode If not used enter 0 Press the key to continue If a zone type or system operation will be used to STOP the relay action enter the appropriate two digit code see the ZT choices listed above If not enter 00 Press the key to continue This screen again displays a summary of the current relay START programming Press the key to continue This screen again displays a summary of the current relay STOP programming Press the key to continue The display then returns again to the first screen so that the next relay number to be programmed can be entered or enter 0 0 to end relay programming Previously entered data can be reviewed by pressing 8 0 After the relay number is chosen
57. Introduction This section provides instructions for programming those fields that affect communications between the control and the central station Trouble Global Remote Arm Disarm Download Quick Arm AWAY MAX STAY INSTANT 601 Programming 1 With at least one Alpha keypad 5137AD or 6139 connected to the Procedure system power up the system If necessary refer to the FINAL POWER UP section for the power up procedure If you had previously connected the AC transformer to the control panel you need only plug in the transformer to 120VAC outlet to power up the system 2 Enter the programming mode by keying the following on the Alpha keypad Installer code 4111 8 0 Fields 40 41 42 Press 40 PABX ACCESS CODE Enter up to the number Enter up to 4 digits if PABX is needed to access an outside line of digits shown Do not If fewer than 4 digits are needed to be entered exit by pressing fill unused spaces and next field number e g 41 To clear entries from field SE press 40 11 for 12 for Press 41 PRIMARY PHONE No 13 for a pause Enter up to 12 digits If fewer than 12 digits entered exit by 2 secs pressing and next field number eg 42 To clear entries from field press 41 Press 42 SECONDARY PHONE No Enter up to 12 digits If fewer than 12 digits entered exit by pressing and next field number eg 43 To clear entries from field press 42 If
58. N again To exit this mode press 00 Adding Custom Words will not be annunciated by 4285 Phone module You can add up to five installer defined words can be added to the built in vo cabulary Each of the five words can actually consist of a word string of one or more words but no more than ten characters can be used for each word or word string Custom words must begin with an alphabetic character If a number or symbol is used as the first character the word will not be saved When adding Custom Words in steps 3 6 the keypad keys perform the following functions DI Advances through the alphabet in ascending order 1 Moves through the alphabet in descend ing order 6 Selects desired letter moves cursor one space to right 4 Moves cursor one space to left 7 Inserts a space at the cursor location eras ing any character lo cated there 8 Saves the new word in the system s mem ory 1 Perform steps 1 2 and 3 of Programming the Descriptors on a previous page Select CUSTOM WORD mode enter 1 when the prompt CUSTOM WORD is displayed Enter the number 1 5 of the custom word or word string to be created for example if you are creating the first custom word or word string enter 1 for the second enter 2 etc A cursor will now appear at the be ginning of the second line One of two methods of entering the custom word s characters can
59. NDING LUGS 2 PROVIDED MUST BE INSERTED IN LEFT HANDTER MINALS OF ANTENNA BLOCKS AND ANTENNAS SECURED TO CABINET SEE RECEIV INSERT IN ER S AND CONTROLS INSTRUCTIONS RIGHT HAND TERMINALS MOUNTING d HOLES TO RELEASE CIRCUIT BOARD REMOVE SCREWS 2 AND BEND BACK TABS S Figure 9 RED ro BLACK gt TO CONTROL S REMOTE Ms GREEN KEYPAD CONNECTION CIRCUIT POINTS EACH RECEIVER BOARD SCH WIRING MUST BE ON INDIVIDUAL OPENING HOME RUN INTERFERENCE DIP SWITCH GIE INDICATOR KNOCKOUT AREA FOR 4 SURFACE H WIRING P ah 4281 5881 amp 5882 Series Wireless Receivers cover removed Installing the 5800TM Module 5800TM Wiring Connections Installation of this module is necessary only if you are using one or more 5827BD Wireless Bi directional keypads The 5800TM must be located between one and two feet from the 4281 or 5881 receiver s antennas The 5800TM must not be installed within the control cabinet Mount the unit using its accompanying mounting bracket Connect the 5800TM to the control panel s keypad connection terminals using the supplied connector with flying leads as follows WIRE TERMINAL ON CONTROL RED 12VDC Terminal 5 BLACK Ground Terminal 4 GREEN Data to Control Terminal 6 YELLOW Data from Control Terminal 7 BLUE Not Used Do not cut any of the jumpers on the 5800TM when using it with the VIA 30PSE For additional information re
60. NT NOTE E Je E CONNECT FOR EXISTING 5 a CORD INSTALLATIONS u Z D EXISTING WIRES Z Qu PREMISES CONNECTED TO THE og 8 a ANSWERING HANDSET TERMINALS m PLUG MACHINE AND ON CONTROL MUST BE 85 36 PHONES MOVED FROM THERE 20 TO TERMINALS 3 AND 4 ON THE 4285 ANSWERING MACHINE TO GND TERMINAL 21 ON CONTROL BROWN T 4285 VOICE MODULE 1234567 4 NOT INSTALLER ADJUSTABLE Wm NOTE IF THE TELEPHONE HAS BUILT IN CALLER ID KEYED THE CALLER ID FUNCTION MAY NOT WORK HEADER GE 4285 TERMINAL ASSIGNMENTS UNUSED YELLOW TO DATA OUT term 7 TIP NO CONNECTION TO CONTROL PANEL a RING f PHONE INPUT CONNECTOR RED TO AUX term 5 TERMINALS USED 3 TIP WITH FLYING BLACK TO AUX GROUND term 4 FOR KEYPAD 4 RING PHONE OUTPUT LEADS GREEN TO DATA IN term 6 CONNECTIONS 5 GROUND I AUDIO OUT 1 I I L 7 FOR FUTURE USE Figure 12 4285 Phone module Wiring Connections a ms Programming The Control For Phone Access 1 With at least one addressable keypad but set to the non addressable mode address 31 connected to the keypad terminals on the control power up the system temporarily If you had previously connected the AC transformer to the control panel you need only plug in the transformer to 120VAC outlet to power up the system 2 Enter the programming mode by keying the following on the keypad INSTALLER code 4 1 1 1 8 0
61. O H EI AAV MODULE JS INSTRUCTIONS Ae N FOR CONNEC Z TIONS TO AUDIO ZS 4 SPEAKERS AND MICROPHONE e aS 2 INPUT TRIGGER l S 4 lt gt e a S aO 4204 CRE 3 V MODULE Q wa 4 Se 5 GND NOTE DO NOT USE ue RELAY 1 FOR RELAY 1 SHOWN OFF Cl NO NC C Ca ANY OTHER PURPOSE D 3 Figure 15 Connection Of AAV Unit When Not Using A 4285 Phone module 5 NCOMING TELCO LINE DIRECT SE CONNECT PU GE pustx Le GRAY RING RING 4285 O BEE ie est Op JACK RING PREMISES aS CIS ANSWERING a z amp MACHINE AND HI PLUG PHONES a lu Sle HIER TERMINALS we 18 19 20 EARTH ON CONTROL CH GROUND ON KERGER E REFER TO HS ae AAV MODULE Ra 4 ZS INSTRUCTIONS e FOR CONNEC Oe TIONS TO AUDIO SPEAKERS AND sl MICROPHONE ol Wil Wiel w 26 a Siama SE Bel lv 4204 SE Q7 GND MODULE PE Qt VDC gua i 15 GND NOTE 16 DO NOT USE gees RELAY 1 FOR PEPAY I SHOWN ANY OTHER PURPOSE Se NO NCC 1 2 3 Figure 16 Connection Of AAV Unit When Also Using A 4285 Phone Module 11 2 Section 12 FINAL POWER UP In previous sections you made temporary power connections for the purpose of programming and testing This s
62. R SUPPLY TERMINAL STRIP AUX AUX DATA DATA IN OUT 4 5 6 T IMPORTANT iil S E MAKE THESE w je je jg Z CONNECTIONS IS Q x Z a DIRECTLY TO lt le lZ lg alo gt SCREW TERMINALS Ja l o IS a Oloiol AS SHOWN Q Q a Q Elgg amp lt LE gt gt gt gt gt gt gt gt LU Ww LU Ww LU LI LU LU Ka Ze TS x Ka SS O O IOO O O O O F FIFI F F F Figure 6 Using A Supplementary Power Supply For Keypads Preliminary Check out Procedure If you want to check that the system is working before connecting field wiring from zones and devices do the following 1 Temporarily connect a 1000 ohm end of line resistor across each of the basic hard wire zones 5 and 6 as shown in the Summary of Connections diagram Without actual zone wiring or EOL resistors connected the keypads in the system will not display the Ready message 2 Power up the system temporarily by plugging the AC transformer previously wired to the control into a 120VAC outlet 3 Busy Standby Alpha keypads or di Fixed word keypads will be displayed After approximately 1 minute the green READY LED or POWER LED on some types of keypads should light and the word READY Fixed word keypads or DISARMED READY TO ARM Alpha keypads should be displayed To bypass the 1 minute delay press plus 0 If the Ready message
63. RF Receiver Circuit Boards Together in the Cabinet 1 Hang two short black mounting clips provided with receiver on the raised cabinet tabs as shown in Detail B in Figure 3 2 Insert the top of the receiver board removed from its own case as de scribed in its instructions into the slots at the top of the cabinet as shown in Detail A in Figure 3 Make sure that the board rests on the correct row of tabs as shown 3 Swing the base of the board into the mounting clips and secure it to the cabinet with the accompanying screws see Detail B in Fig 3 4 Insert the top of the control s board into the slot in the clips and position two ong red clips at the lower edge of the board see Detail C 5 Swing this board into place and secure it with two additional screws 6 Insert grounding lugs supplied with the receiver through the top of the cabinet into the eft hand terminals of the antenna blocks at the upper edge of the receiver board and secure them to the cabinet top with the screws provided as shown in Detail D 7 Insert the receiver s antennas through the top of the cabinet into the blocks right hand terminals and tighten the screws 8 Setup and wiring of the receiver is contained in the WIRELESS RF ZONE EXPANSION 5700 amp 5800 RF SYSTEMS section Standard Phone Line Connections module is used Refer to the 4285 Phone module section for information A The wiring connections shown here are not app
64. Red and Black wires on the battery connector cable to the control board as follows t a Red to the positive battery tab on the control board see Summary of Connections Diagram for location if necessary b Black to the negative battery tab on the control board T These wires may have already been connected to the battery tabs on the control board If so disregard steps a and b DO NOT CONNECT THE WIRES TO THE BATTERY YET UL Use a 4AH battery or larger for UL installations Earth Ground Connections The designated earth ground terminal 21 must be terminated in a good earth ground for the lightning transient protective devices in this product to be effective The following are examples of good earth grounds available at most installations Metal Cold Water Pipe Use a non corrosive metal strap copper is recommended firmly secured to the pipe to which the ground lead is electrically connected and secured AC Power Outlet Ground Available from 3 prong 120VAC power outlets only To test the integrity of the ground terminal use a three wire circuit tester with neon lamp indicators such as the UL Listed Ideal Model 61 035 or equivalent available at most electrical supply stores Section 3 INSTALLING REMOTE KEYPADS This section lists the wired keypads that may be used and provides instructions for wiring and mounting the keypads A preliminary check out procedure is also provided to ensure
65. SCII CHART For Adding Custom Words 32 space 42 52 4 62 gt 73 82 R 33 43 53 5 63 74 J 83 S 34 44 54 6 64 75 K 84 T 35 45 55 7 65 A 76 L 85 U 36 46 56 8 66 B 77 M 86 V 37 47 57 9 67 C 78 N 87 W 38 amp 48 0 58 68 D 772H 88 39 49 1 59 69 E 9 o 89 Y 40 50 2 60 lt 70 F 80 P 90 Z 41 51 3 61 71 G 81 Q 13 5 13 6 Section 14 SEQUENTIAL MODE for 5800 Series Wireless Transmitters Use this mode only after all other zone information has been programmed including transmitter loop numbers There are two methods of enrolling you can enroll each transmitter into the system as you are entering the zone information in field 56 the procedure will be found in the WIRELESS RF ZONE EXPANSION section or you can enroll all the transmitters in 83 menu mode after all other zone information has been entered in field 56 The enrollment method in 83 is called sequential mode and is described in this section As an option the new enrollment mode allows you to use a 5804 button type transmitter as a program tool The advantage of using a program tool is that it tells the control that you are about to enroll a transmitter into the system You can move to the physical location of the transmitter to be enrolled press the upper left hand button of the program tool and then trip the intended transmitter see step 10 for operation This helps to prevent random signals from being accep
66. STRUCTION NOTICE NOT TO BE REMOVED WEEKLY TESTING IS REQUIRED TO ENSURE PROPER OPERATION OF THIS SYSTEM ADEMCO ALARM DEVICE MANUFACTURING CO A DIVISION OF PITTWAY CORPORATION 165 Eileen Way Syosset New York 11791 Copyright 1997 PITTWAY CORPORATION N7225V2 4 97
67. Sniffer mode for this as it will only check for transmission of one zone on a particular transmitter and NOT the zones assigned to each additional loop Temporarily Or Permanently Removing A Zone From The System 5800 System 1 Enter the programming mode Key Installer Code 8 0 and press 5 6 2 Enter the zone number and press A summary display will appear 3 Press again 4 The Zone Type prompt will appear Enter 0 0 This sets the zone type to Not Used Not Used 00 Press to continue 20 Zone Type 20 Delete Zone 5 E will ask whether you want to 1 Yes 0 No Yes will permanently remove the zone from the system while a No will disable it but retain all data except the original zone type You can then go back to this zone later and put back an active zone type to re enable it A serial number that has been entered for a 5800 system will not be deleted if the zone is temporarily disabled by answering No to the prompt above If only the physical transmitter is to be removed or changed i e its serial number deleted as when replacing a unit that has a non removable battery it can be done in 56 Mode as indicated next Deleting a Transmitter Serial Number From a Zone in 56 Mode 5800 System The abbreviated procedure below can be used to delete a serial number from a zone using the 56 Mode 1 In the programming mode press 5 6 to enter Zone Programming m
68. TAMPER use N C setting POS 6 UP N O DN N C DIP SWITCH POSITION T 8 DIP SWITCH POSITION DIP SWITCH POSITION 10 UP UP ddeclelelele clalcielsiele CIS H IPL TTYL TL EYL a 3 0 ed ool ed 5 0 5 5 5 STEEL ISIS SISISISISIS SISISISISISIS 55 5515155 5 5 5 5 5 5 5 HEP TELE EEE le 2 UP UP UP UP UP UP UP UP UP UP UP UP UP UP UP ell ul ISISISISISISISISH Il ht SISISisisisis no bad nod ne dd iodo aod od no aod ao a a D D 8 a D R a For 5700 series transmitters not shown in this table refer to the instructions accompanying each transmitter Compatible 5700 Series Transmitters Zone ID Panic Transmitter 62 or 63 Programmable for either silent or audible 24 hour alarm Photoelectric Smoke 48 55 Detector One piece smoke detector with built in transmitter Built in UL Listed 85dB piezo electric
69. TEMENT This equipment complies with Part 68 of the FCC rules On the front cover of this equipment is a label that contains among other information the FCC registration number and ringer equivalence number REN for this equipment If requested this information must be provided to the telephone company This equipment uses the following jacks An RJ31X is used to connect this equipment to the telephone network The REN is used to determine the quantity of devices which may be connected to the telephone line Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call In most but not all areas the sum of the RENs should not exceed five 5 0 To be certain of the number of devices that may be connected to the line as determined by the total RENs contact the telephone company to determine the maximum REN for the calling area If this equipment causes harm to the telephone network the telephone company will notify you in advance that temporary discontinuance of service may be required If advance notice is not practical the telephone company will notify the customer as soon as possible Also you will be advised of your right to file a complaint with the FCC if you believe necessary The telephone company may make changes in its facilities equipment operations or procedures that could affect the operation of the equipment If this happens the telephone company will provide advance notice in order f
70. TO HI SIDE EOLR OF ZONE 5 TERM 14 SC TOLO SIDE DETECTOR OF ZONE 5 TERM 15 Figure 7 4 wire Smoke Detector Connections Zone 5 Compatible System Sensor 4 Wire Smoke Combustion Detectors 1412 4 wire ionization products of combustion detector 2412 4 wire photoelectric smoke detector 2412TH 4 wire photoelectric smoke detector w 135 F 57 C heat detector A77 716B EOL relay module supervisory module for wired 4 wire fire zone 2112 24T Low profile 4 wire photoelectric smoke detector w 135 F 57 C heat detector Programming Hard Wired Zones 1 With at least one 2 line Alpha keypad 5137AD or 6139 connected to the keypad terminals on the control power up the system temporarily If you had previously connected the AC transformer to the control panel you need only plug in the transformer to 120VAC outlet to power up the system 2 Enter the programming mode by keying the following on the Alpha keypad INSTALLER code 4 1 1 1 8 0 SC Data fields 22 RF SYSTEM and 25 OUTPUT RELAY MODULE must be programmed as required before continuing 3 Press 56 Note that this is an interactive programming mode You will use it to program zone numbers zone types and alarm report codes for hard wired zones and RF zones Note If you enabled the 5800 wireless system in field 22 a 2 entry the first screen prompt will be Program Tool 0 No 1 Yes Enter 0
71. User No 811 Trouble NNN Zone No t The first digit of the Subscriber No entered in field 43 must be 1 9 DO NOT USE 0 the last 3 digits can be 0 9 Failure to observe this requirement may interfere with paging services 15 4 TO PROGRAM SYSTEM STATUS AND RESTORE REPORT CODES 60 68 70 75 Example 1 Pager displays 1834 911 664 This indicates that Subscriber No 1234 s system is reporting an Alarm 911 due to zone 4 being faulted 004 This indicates that Subscriber No 1234 s system is reporting an opening 001 by User 5 005 Note that no restore reports are sent to the pager Important Do not use AAV when Paging or Alarm Reports are being sent to a Secondary number If this is done the call to the Secondary number by the communicator after the alarm report will prevent the AAV from taking control of the phone line and the AAV Listen in session cannot take place Press 48 15 SECOND DIALER DELAY BURGLARY Enter 0 for no or 1 for yes Default is 0 no delay Press 49 PERIODIC TEST REPORT Select the desired test report interval 0 none 1 24 hours 2 weekly 3 30 days Default is 0 none Test Report Code entered in field 64 is sent Reports with Subscriber No Press 50 SESCOA RADIONICS SELECT 0 Radionics 0 9 B F reporting 1 SESCOA 0 9 only reporting Select 0 for all other formats Default is 0 With a 3 1 or 4 1 St
72. When the system sees activity on the appropriate input it will beep three times and display the confirmation message Press or the upper left hand button of the program tool when you are ready to enroll the next transmitter At any time during this step you may press the key on the keypad or the upper left hand button of the program tool if you are satisfied with the serial and loop number combination that has been enrolled regardless of whether or not the enrolled input has been confirmed This will ready the system to enroll the next transmitter If the incorrect transmitter has been enrolled press the key on the keypad or the upper right hand button of the program tool to delete the serial number and return to the LEARN S N prompt A single long beep will be heard from the keypad to verify pressing of the upper right hand button Then press 1 Yes or press the upper left hand button of the program tool a single short beep will verify the system is ready for enrolling and re activate the proper transmitter or transmitter loop input 14 2 7 The system will search for the next zone that does not have a serial number associated with it If one is found the prompt in step 5 along with the appropriate zone number will be displayed Follow steps 5 and 6 for the remaining wireless zones S If you are enrolling transmitters which have already been physically installed move to the location of the
73. Zone numbers for amp or B 99 3 1 4 1 Expanded 4 2 SSS S A SSSS AZ AAA A Z SSS S T SSSS Tt TTT T t SSS S B SSSS Bb BBB B b SSS S E SSSS EAc EEE E Ac SSS S L SSSS LLp LLL L Lp SSS S O SSSS OU OOO O U SSS S C SSSS CU CCC C U SSS S G SSSS Gg GGG G g SSS S R SSSS RZ RRR R Z SSS S R A SSSSR Ac RaRaRa Ra Ac SSS S RL SSSS R Lp RLRLRL RDLB SSS S RT SSSS Pri RTRTRT ir SSS S Rp SSSS Rgb RgRgRg R p b C Close Code 1st Digit U User Number in hex Gg Test Code 1st amp 2nd digits R Restore Code Alarm Ryt Restore Code Trbl 1st amp 2nd digits Rpb Restore Code Byps 1st amp 2nd digits RaAc Restore Code AC 1st amp 2nd digits R Lp Restore Code Bat 1st amp 2nd digits 1 or A 95 Duress 8 3 or C 96 Tamper 9 Ademco Contact ID Reporting takes the following format CCCC Q EEE GG ZZZ where CCCC Customer subscriber ID Q Event qualifier where E new event and R restore EEE Note ZZZ Event code 3 hexadecimal digits For a complete list of event codes refer to the central office receiver manual GG Always 00 Zone contact ID number reporting the alarm or user number for open close reports System status messages AC Loss Walk Test etc contain zeroes in the ZZZ location 15 2 TABLE OF CONTACT ID EVENT CODES e 131 Periodic Test Fire Loop Trouble 606 AAV to follow Communication Programming
74. adio If communication is lost or a trouble develops a message will be attempted to be sent via both radio and telephone to the central station For complete information see the manual that accompanies the radio Wiring Connections Connect the data in data out terminals and voltage input terminals of the Long Range Radio to the control s keypad connection points terminals 4 5 6 and 7 as shown below RED 7720 PLUS 7820 GREEN LONG RANGE RADIO CG YELLOW CONTROL TERMINALS Figure 14 Long Range Radio Connections Programming for Long Range Radio 1 With at least one keypad connected to the keypad terminals on the control power up the system temporarily If you had previously connected the AC transformer to the control panel you need only plug in the transformer to 120VAC outlet to power up the system 2 Enter the programming mode by keying the following on the Alpha keypad INSTALLER code 4 1 1 1 8 0 3 Press 27 OUTPUT TO LONG RANGE RADIO Enter 1 when using a Long Range Radio enter 0 if not default is 0 If yes is selected any dialer report programmed to report to the PRIMARY phone number in field 47 will be sent as well via long range radio All dialer and long range radio reports will be in Contact ID format regardless of the selection made in field 46 Full Trouble and Restore messages are sent 5 Program the long range radio for device address 3 on the keypad lines 6 Exit the programmin
75. ady for next word 10 The two words in our example have now been entered Note however that up to three words may be entered provided the number of characters will fit on the screen Press 8 to save all words in memory The A with the flashing cursor over it will disappear indicating that the word s are stored in memory for that zone as shown in the display at the left 11 To enter a descriptor for the next zone press plus the desired zone number eg 02 The summary display following step 4 previously will appear Now repeat steps 6 through 10 for the descriptor for the next zone 12 To exit the Alpha descriptor mode press k00 at the summary display This prompt will be displayed Program Alpha 0 No 1 Yes 00 Alpha Pgm 13 Press 0 This will be displayed 82 14 Press 99 to exit the programming mode Alternate Method For Programming Zone Descriptors 1 Perform steps 1 through 5 of the previous method When entering the Zone 2 Note that the first letter of the alphabet appears after the zone number Descriptors using this and that the zone number is automatically included with the description f method the keypad keys there already is a description for the zone the description will appear with perform the following no cursor since this is a display mode To enter or change a description functions press Zone Number again A flashing cursor will n
76. age indicating Exit Alarm is sent to the central station and a zone indication and Exit Alarm or EA is displayed on the keypad For expanded or 4 2 reporting a 2nd digit is sent and is the same as the 2nd digit of the zone alarm report code programmed in field 56 For Contact ID reporting Event code 374 and the zone number is sent There is no restore message for an Exit Alarm report ARM AWAY STAY REPORT CODES This option allows for independent programming of AWAY and STAY reports 2nd digit of Report is User No if expanded or 4 2 reporting is selected RF XMTR LOW BATTERY REPORT CODE This is sent in the event that a wireless transmitter low battery condition exists CANCEL REPORT CODE This is sent upon disarming of the system after an alarm condition was reported ALARM RESTORE REPORT CODE 1st DIGIT This is sent when the zone that caused an alarm is restored to its non faulted condition 2nd digit is automatically sent as the 2nd digit of the zone alarm report code programmed in field 56 if expanded or 4 2 reporting is selected TROUBLE RESTORE REPORT CODE This is sent when a trouble in a zone is restored BYPASS RESTORE REPORT CODE This is sent when a zone that has been bypassed is un bypassed 15 6 Press 73 AC RESTORE REPORT CODE This is sent when AC power has been restored after an AC power outage Press 74 LOW BAT RESTORE REPORT CODE This is sent when a system low battery condition is restored to no
77. andard Format Enter a code in the first digit box 1 9 0 B C D E or F Enter 10 for 0 11 for B 12 for C 13 for D 14 for E 15 for F A 0 not 10 in the first digit box will disable a report A 0 not 10 in the second digit box if any will result in automatic advance to the next field when programming With an Expanded or 4 2 Format Enter codes in both boxes 1st and 2nd digits for 1 9 0 or B F as described above A 0 not 10 inthe second box will eliminate the expanded message for that report A 0 not 10 in both boxes will disable the report With Ademco Contact ID Reporting Enter any digit other than 0 in the first box to enable zone to report This is an enabling code only and is disregarded in the actual reporting to the central office Entries in the second boxes will be ignored A 0 not 10 in the first box will disable the report Examples For Code 3 Single Digit enter For Code 32 Two Digits enter For Code B2 Hexadecimal enter Press 60 TROUBLE REPORT CODE This will be sent if a zone goes into trouble Press 61 BYPASS REPORT CODE This will be sent when a zone is manually bypassed 15 5 Press 62 Press 63 Press 64 Press 65 Press 66 Press 67 Press 68 Press 70 Press 71 Press 72 AC LOSS REPORT CODE Reports with Subscriber No Timing of th
78. andby battery connection is automatically checked every 3 minutes CSFM requirement In addition entry into the test mode will cause a battery test to be initiated If there is no battery or a low battery a low battery message is displayed and if so programmed will be reported to the central station Calculating the Determine the total device current draw after filling in the AUXILIARY DEVICE Battery Size CURRENT DRAW WORKSHEET on the next page To this figure add the Needed 4100mA that is drawn by the control panel itself Then to determine the battery size needed use the following formula Total Current Drawn x Number of hours standby wanted Battery Ampere Hours Convert mA figure to decimal Amps see example Example If total auxiliary device current drawn is 450mA add 100mA for the control panel for a total of 550mA 0 55 amps if 24 hour standby is wanted the calculation will be 0 55mA x 24 hours 13 2 Ampere Hour battery needed In this example two 7 Amp Hr batteries connected in parallel must be used Making the Battery Connections 1 Use the battery standby formula shown on previous page to select the appropriate battery for the installation Remember when calculating the battery size needed you must add the 100mA drawn by the control itself to the total Auxiliary current draw in the worksheet that follows 12 1 Do not connect the battery until all devices have been wired to the control wh
79. basic hardwired zones having the following characteristics e 300 500 millisecond response time e EOLR supervision supporting N O or N C sensors e Zone 5 supports as many 4 wire smoke or heat detectors as can be powered from the control e Zone 7 95 and 96 are keypad Panics e Zone 8 is Duress e Zone 9 is Tamper Optional Expansion Zones 30 total wired and wireless Wired Supports up to 8 additional wired zones using a 4219 expansion module or a Expansion 4229 expansion relay module Expansion zones have the following characteristics e EOLR supervision supporting N O or N C sensors e 300 500 msec normal response with an option for fast 10 15msec response on loop A first expansion zone Wireless Supports up to 30 wireless zones less if using wired expansion zones Expansion Requires the use of a 4281 type RF receiver with 5700 series wireless transmitters or 5881 5882 in Canada type RF Receiver with 5800 series wireless transmitters as shown below Receiver Model No of Zones Transmitter Type 4281L Up to 4 5700 4281M Up to 8 5700 4281H Up to 8 5700 5881L 5882L Up to 8 5800 5881M Up to 16 5800 588 1H 5882H Up to 30 5800 5882L or 5882H used in Canada Remote Keypads Supports up to 4 of any of the following keypads Fixed Word Keypads 4127 4137AD 6127 6128 and 6137 These keypads cannot be used if the 4285 Phone module is being used Alpha Keypads 5137AD 6139 2 line alphanumeric
80. ber of zones that can be used which is shown in Table 1 above Wireless System Operation and Transmitter Supervision The receiver responds to status and alarm signals from wireless transmitters operating at 345MHz for 5700 series in USA 815MHz in Canada and 345 MHz for 5800 series in USA and Canada within a nominal range of 200 feet the receiver then relays this information to the control Except for transmitters that may be carried off premises such as the 5700 system s 5701 and 5727 the 5800 system s 5802 5802CP 5803 5804 and 5827 and either system s 5827BD each transmitter is supervised by a check in signal that is sent to the receiver at 70 90 minute intervals If at least one check in is not received from each supervised transmitter within a 12 hour period the missing transmitter number s and CHECK will be displayed on the keypad Transmitter Battery Life The supervision for a particular transmitter in the 5800 system may be turned off by entering it as a UR unsupervised RF type as described later 5800 series transmitters have built in tamper protection and will cause a CHECK condition to be annunciated if covers are removed Each transmitter is also supervised for low battery and will transmit a low battery signal to its receiver with the battery having at least 30 days of life re maining A low battery message and appropriate zone number will appear on a wired keypad s display If
81. by using the Panic keys or key pairs on some keypads If a key or key pair has been programmed for audible emergency the keypad will emit a steady alarm sound and ALARM and zone number will be displayed If a key or key pair has been programmed for silent emergency there will be no audible alarms or displays but a report will be sent to the Central Station If a key or key pair has been programmed for Fire the keypad and external sounder will emit an interrupted alarm sound and ALARM FIRE and zone number will be displayed Silence alarms by entering the security code and pressing OFF 9 If Output Relay Units have been installed test their programmed action 10 Notify the Central Station when all tests are finished and verify results with them Continued 16 1 To test the wireless part of the system and the RF Receiver perform the two following tests Transmitter Sniffer Mode and Go NoGo Test Mode TRANSMITTER SNIFFER MODE Make sure the system is disarmed before trying to enter this mode Key Installer code 3 This initiates a procedure that will check that all 5700 series transmitters have been properly programmed Note If the communicator is in the process of sending a report to the Central Station the system will not go into the Sniffer mode If so wait a few minutes and try again The keypad will display all zone numbers of wireless units programmed into the system As the system receives a signal
82. ccceeeeeeeeeeceeeee ceeeeeaeceaaeeeeeeeeeaeescaeeeea ceseeeeeeaees 9 2 Testing the Gounder usine 9 2 LONG RANGE RADIO nnna 10 1 General Information iii 10 1 Ee EE 10 1 Programming for Long Range Radio ccccceeeseeeeeseeee rae e E EE EEE kE ES 10 1 AUDIO ALARM VERIFICATION AAV UNIT 11 1 General Information 1 mariaa aana EE ENEE iandae aait 11 1 Wiring Connections A 11 1 Programming 225882 2m ene ne ve sed des i dn Wel he eee aero cet ee ee deed 11 1 FINAL POWER TT 12 1 Earth Ground Connections iii 12 1 AG e UW ices tie tte Ate tin E E 12 1 Connecting the Back Up Battery sis 12 1 Calculating the Battery Size Needed ceecceeeeeeeeeeeeee ceeeeseeeeceeeeeeeeeeaeeeeneee seat 12 1 Making the Battery Connections cceeeceeeeeeceee eee eeeeeaeeeeeeeeeeeesaeesaeeeeaa eeeneeeeaees 12 2 Auxiliary Device Current Draw Workeheet caeeseeeeseeeeseaeeeaeeneeeee anes 12 2 Section 13 Section 14 Section 15 Section 16 Section 17 Section 18 Section 19 Appendix A Appendix B ALPHA DESCRIPTOR PROGRAMMING 13 1 Assigning Zone Descriptors eeeeeeeeeeeeeeeeneee ceeeeeeeeeeeeeeeeeeaeeeeeeaeee eeseeeeeeeeneaeeeeeeaaees 13 1 Entering Zone Descriptors in program Menu Mode 82 13 1 Programm
83. ck up to the Program Tool prompt The serial number for the program tool will only remain in the system until the programming mode is exited Entering 97 will not delete the tool Press to continue 00 Input S N L A123 4567 3 4 Enter the zone number that you wish to program As an example zone Enter Zn Num 10 is shown here 00 Quit 10 Press to continue Zone 10 entered 7 5 A display will appear showing a summary of that zone s programming L If the zone is not programmed the display will appear as shown here If 1 checking a zone s programming and it is programmed satisfactorily press to back up one step and enter another zone number if desired Otherwise press to continue ZN ZT RC In 10 00 00 RF JL Zone Number 10 Z T 6 Each zone must be assigned a zone type which defines the way in ong Se which the system responds to faults in that zone Enter the zone type Perimeter desired or change it if necessary Available zone types are 00 Zone Not Used 08 24 Hr Aux Entry for Zone Type 06 01 Entry Exit 1 Burglary 09 Fire SNOWN 02 Not Used 10 Interior w Delay 03 Perimeter 20 Arm Stay 04 Interior Follower 21 Arm Away 05 Trouble Day Alarm Night 22 Disarm 06 24 Hr Silent 23 No Alarm Response 07 24 Hr Audible EX Relay activation These are special zone types used with 5800 series wireless pushbutton units which will result in arm
84. cluded in the installation you should note the following When calling in from an off premises phone to receive a status report or execute a command the user should make the initial call allow 1 to 3 rings only and hang up Then call in again the Phone Module will now seize the line and 2 long tones will heard followed by the usual voice prompt for the 2 digit phone access code If this procedure is not followed Phone Module operation will not be possible 96 INITIALIZE DOWNLOAD ID AND SUBSCRIBER ACCT No FOR DOWNLOADING No data entry required This completes the communication programming Exit the programming mode by keying 99 Refer to the TESTING THE SYSTEM section to check system operation 15 7 Section 16 TESTING THE SYSTEM Test Procedure After installation is completed the System should be carefully tested as follows 1 With the System in the disarmed state check that all zones are intact If a NOT READY message is displayed press the key to display the faulted zone s Restore faulted zone s if necessary so that the READY message is displayed 2 Enter the security code and press the TEST key The external sounder will sound for 1 second If the backup battery is discharged or missing the sounder may not turn on and a LOW BATTERY report will be transmitted with a TEST report Note that the keypad will beep once every 40 seconds as a reminder that the system is in the Test Mode 3 Fault and res
85. code consists of 2 hexadecimal digits each in turn consisting of 2 numerical digits For example for a report code of 3C enter 0 3 for 3 and 1 2 for C See the SYSTEM COMMUNICATIONS section for complete information on report codes if necessary Press to continue For the hardwired zones HW and the zones for a 5700 system s transmitters RF the Input Device types are automatically assigned Panic Duress and Tamper inputs are not applicable Special Notes on Zone Programming 5700 RF Systems Go No Go Test 10 Mark the zone number on the transmitter 11 After the transmitter has been entered into the system press to continue Typical summary display Zn ZT RC Im L 20 03 3C RF A summary of the programmed values for the selected zone will now be displayed If all is okay press for the next display 5 Alpha descriptors for the zones can be done Program Alpha now or may be done at a later time using 82 0 No 1 Yes 0 interactive mode enter 0 Refer to ALPHA DESCRIPTOR PROGRAMMING section for performing this procedure in the 82 interactive menu mode If O no was entered in response to the Enter Zn Num Program Alpha question a prompt will 00 Quit 21 then be displayed for entry of the number for the next wireless zone to be programmed 12 Proceed with the programming of the next wireless zone starting at step 5 again 13 To exit field 56 when
86. cons to denote critical notes and technical tips to assist you with the installation of this system see next page CONVENTIONS USED IN THIS MANUAL MAIN SECTION TITLES ARE SHOWN IN REVERSE TYPE UL These notes include specific information which must be followed if you are installing this system for a UL Listed application with the installation and which if not observed could result in operational difficulties 4 These notes include information that you should be aware of before continuing could seriously affect the operation of the system or could cause damage to the system Please read each warning carefully This symbol also denotes warnings about physical harm to the installer IN This symbol indicates the presence of critical information that if not observed Many system options are programmed in an interactive menu mode by responding to Alpha keypad display prompts These 00 Quit prompts are shown in a double line box Enter Zn Num 00 When programming the system data fields are indicated by a star followed by the data field number PRODUCT MODEL NUMBERS Unless noted otherwise references to specific model numbers represent Ademco products vi Section 1 GENERAL DESCRIPTION The VIA 30PSE is a control that supports up to 32 zones using basic hardwired wired expansion and or wireless plus remote keypads Basic Hardwired Zones 5 and 6 Provides 2
87. ction provides instructions for mounting the 4285 Phone module wiring the Phone module and for programming the system for phone access via the Phone module Installing the Phone module General The 4285 Phone module is an add on accessory for the VIA 30PSE that Information permits access to the security system via a Touch tone phone either on premises or by a call in when away The Phone module can announce many of the same words that would normally be displayed on an Alpha keypad under the same system conditions When using the 4285 Phone module addressable keypads must be used in the system but set to the non addressable mode address 31 i e do not use a 4127 or 6127 keypad When properly connected the 4285 Phone module will enable the user to do the following via a Touch tone telephone a Receive synthesized voice messages over the phone regarding the status of the security system b Arm and disarm the security system and perform most other commands using the telephone keypad with voice annunciation being provided over the phone as confirmation after a command is entered The phone used for phone access must have Touch tone capability though Touch tone service is not necessary if premises uses PULSE dialing switchable phones must be set for Touch tone temporarily before attempting phone access A Phone Access User s Guide for phone access to the security system is provided with the Phone module for the u
88. dee EE a ege 17 4 General Information eege REENEN EE 17 4 Check and Battery Displays ccecccceeceeeeeees ceeeeeeeeeeeceeeeaeeeseaeseaaes ceeeeeeeeeaee 17 4 ower F aluro eege eise Eeer ee ated eee ae ede 17 4 Other Displays antenne tale ely eee Sege 17 4 TROUBLESHOOTING GUIDE 18 1 Contacting Technical Gupport sisi 18 3 SPECIFICATIONS amp ACCESSORIES 19 1 Eiere Mee EE 19 1 Accessories Compatible Devices cccccceeceeeeeeeee ceeeeaeeeeaeeseseeseeeeeseeeeaa eeeeneeeenees 19 3 REGULATORY AGENCY STATEMENTS ccesceeeeeueeeeeeneeeeeeuseuseueeeeeeans A 1 LIMITATIONS OF THIS ALARM SYSTEM cccceccseeseeseeseeeeeeeeeeeeeeneaneas B 1 LIMITED WARRANTY ccccceneeneeneeneeeeseeseusceaeeaeeaeeaeueeaeuaeuagueeegeegeeaees B 2 SUMMARY OF CONNECTIONS DIAGRAM ss Inside Back Cover NOTE A separate Programming Guide is supplied with this manual Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 Figure 10 Figure 11 Figure 12 Figure 13 Figure 14 Figure 15 Figure 16 Figure 17 LIST OF FIGURES Installing the Cabinet LOCK sn eee ene 2 1 Installing The PC Board Alone or if used With a 4204 4219 or 4229 Module cccccccccccccsesnsesesnsusnen sususesusesususesnsnsesesesess 2 2 Installing the PC Board amp RF Receiver Toge
89. descriptor for zone 1 enter plus the next zone number for which you wish to enter or check a descriptor A summary display for that zone will appear You must then press plus the same zone number again to gain access to the entry mode flashing cursor for that zone Flashing Cursor 6 Press plus 3 digit number for the first word from the ALPHA ZN 01 BACK VOCABULARY LIST on a following page Example The descriptor that we wish to enter for zone 1 is BACK DOOR From the list BACK 013 Therefore you would enter 0 1 3 Note If you accidentally enter the wrong word simply press plus the correct 3 digit number for the word you want ZN0O1 BACK 7 Press 6 to accept the selected A word and continue Note lf this is the only word you are Flashing C if 6 j using for the descriptor press 8 GE Geen is S instead of 6 to save that word in ready for next word memory and then go to step 11 8 Enter the 3 digit number for the next ZN 01l BACK word In our example the word is DOOR DOOR whose number is 057 Enter 0 5 7 This display will appear T Flashing Cursor 13 2 ZN01 BACK 9 Press 6 to accept the selected word DOOR Note f these are the only words you are using for the descriptor press 8 instead of 6 to save them in memory Flashing Cursor if 6 is pressed system re
90. displays 6138 1 line alphanumeric display For programming from a keypad a 5137AD or 6139 2 line Alpha keypad must be connected but need not necessarily stay in the system Security Codes e One Master code for entire system user 2 Installer code is user 1 e 4secondary user codes users 3 6 e One duress code User 8 Duress Code An emergency code which when used to disarm or arm the system will send a silent duress message to the central station xh Keypad Panic Keys e Upto 3 programmable panic key functions are provided e Designated as Zones 95 96 7 e Activated by wired amp wireless keypads e Reported separately distinguished by subscriber ID number Paging Feature If the paging feature has been programmed for your system your pager will respond to certain conditions as they occur in your system and display code numbers indicating the type of condition that has occurred Quick Arm Feature Quick Arm may be programmed allowing use of the key in place of the security code for arming Quick Arm will not work unless the Master code has been programmed into the system Optional Output Relays Supports up to 4 relays using one 4204 Relay Module or 2 relays using one 4229 Zone Expansion Relay Module e Actions programmable to respond to zone activity or manual keypad entries Optional Phone module Supports the Ademco 4285 VIP Phone Module e Provides access to the system via
91. dom flicker is OK Installing the Lock if used Use an Ademco No N6277 Cam Lock and No N6277 1 Push On Clip Retainer Clip Note The cabinet can be closed and secured without a lock by using 2 screws in the cover s edge 1 Remove the cabinet door P P RETAINER CLIP is easily removable for f OAOE POSITS servicing and is easily re i installed 2 Remove the lock knockout RETAINER from the control cabinet SLOTS door Insert the key into the LOCKED RETAINER 9 CLIP lock Position the lock in the SA hole making certain that the TR latch will make contact with re the latch bracket when the door is closed 3 Hold the lock steady and in CABINET DOOR BOTTOM sert the retainer clip into the retainer slots Position the clip as illustrated in order to permit easy removal Figure 1 Installing the Lock xh Before installing the cabinet s contents remove the metal cabinet knock outs required for wiring entry Do not attempt to remove the knockouts after the circuit board has been installed Installing the Control s Circuit Board Alone or if used with a 4204 4219 or 4229 Relay Unit Control s Circuit Board 1 Hang two long Red mounting clips provided on the raised cabinet tabs see Detail B in Fig 2 2 Insert the top of the circuit board into the slots at the top of the cabinet Make sure that the board rests on the correct row see Detail A in Fig 2 3
92. e ID code not set in field 24 or transmitter not set to same house code set in that field Transmitter located too for from 4281 5881 Metal shielding between transmitter and 4281 5881 Transmitter malfunctioning 4281 5881 malfunctioning Transmitter No zone not programmed 4281 5881 address incorrect Field 22 not set properly Transmitter zone type ZT is set to 00 Not Used Transmitter battery not installed 5700 System transmitter s DIP switch not set properly house ID and transmitter ID 5800 System transmitter serial No not entered in system With 5700 System no response at all to any transmitter Bat or System Lo Bat no zone Nos Bat or Lo Bat 00 Bat or Lo Bat nn System is in TEST mode A wireless transmitter low battery has occurred and is displayed A supervision CHECK has occurred Put control in TEST mode If zone does not re spond try operating the tamper switch or another input to the transmitter 5a 5b If another input causes the zone to be dis played the wrong loop input was entered when programming If no response at all from this transmitter this physical transmitter has not been entered into the system Go NoGo display is being cleared by another unit programmed for this zone Sensors not properly installed wired or monitored Universal transmitter 5715 5817 pro grammed wrong Protected door or window opened while
93. e assigned to User Number 8 To program a Duress code 1 Enter Master Code 2 Press the CODE 8 key 3 Press the 8 key again 8 Duress code User No 4 Enter the desired 4 digit Duress Code The keypad will beep once Note The Duress code must differ from the Master Code or any other User s Code To change the Duress code Repeat steps 1 2 and 3 and then step 4 with the new Duress Code To delete the Duress code Perform steps 1 2 and 3 and then stop When the keypad beeps once it signifies that the code has been deleted 17 1 Keypad Functions General Information Arming Functions Note that if you enabled QUICK ARM field 21 the key can be pressed instead of entering the security code for any of the arming procedures Away Stay Instant Maximum etc The security code is always required however when disarming the system NOTE The Quick Arm feature will function only if the Master Code has been programmed see Assigning the Master Code on the previous page The keypad allows the user to arm and disarm the system and perform other system functions such as bypassing zones and display zone descriptors Zone and system conditions alarm trouble bypass are displayed in the Display Window When an alarm occurs keypad sounding and external sounding will occur and the zone s in alarm will be displayed on the keypad Pressing any key will silence the keypad sounder for 10 seconds Disa
94. e enr Que NEEN Eed eect ddr ae Ad 6 16 Deleting a Transmitter Serial Number From a Zone in 56 Mode 5800 System 6 16 Check out Procedure for Wireless ZONES ccceccceceeeeeeeeee eeeeeeeceeeeaaeeeeaeeteneeseee anaes 6 16 Transmitter ID Sniffer Mode 5700 RF Systems Only sessen eer 6 16 Go No Go Test Mode 5700 and 5800 RF Systems 6 17 RELAY OUTPUT DEVICES unten timides 7 1 Relay Device Basics e ecciatiiteteltins hihi eee ee ee eee eee deeded te et 7 1 4204 Relay Modules eeh ege dese eege gege e e EE EAE Seege EE Eege 7 1 A204 le EE 7 1 SUPERVISION EE 7 1 Programming Options Defned ceeeeeeeeecaeeeeaeeeeneeseaeeee qeeesaaeeseeeseeeeesaes 7 1 Programming Output RelayS sisi 7 3 Example of Output Relay Programming ceeeeeeeeeeaaeeeseeeeeeeeteaeen aes 7 5 4285 PHONE MODULE ecaeesaaeeesaeeseeeseneees 8 1 Installing the Phone module 8 1 General Informations ae At MAN RE An hahaa ee 8 1 Mounting The Phone module eeeeaeeeeneaeeenes 8 1 PRONG module Wirng f25rsssseensstmrnese tte E EE ER tnt fente EE eme EKRE 8 1 Galles OASIS Kee Ee nn nee 8 2 Programming The Control For Phone ACCESS ccccececeeeeeeeeee caeeeeeeeeseaeeesaeeseneeenaees 8 4 Checking the Operation of the 4285 Phone module eeeeeeeeeeeeeeeteaees 8 5 EXTERNAL SOUNDERS A 9 1 Compatible Sounders ee ee ana ean sl aie Se tite 9 1 Sounder Connections ii eegeeesaeessaesseaeesseeeesees anaes 9 2 Programming For External Sounders cc
95. ection devices Users of alarm systems owe it to themselves and their loved ones to learn about these developments ADEMCO LIMITED WARRANTY Alarm Device Manufacturing Company a Division of Pittway Corporation and its divisions subsidiaries and affiliates Seller 165 Eileen Way Syosset New York 11791 warrants its products to be in conformance with its own plans and specifications and to be free from defects in materials and workmanship under normal use and service for 24 months from the date stamp control on the product or for products not having an Ademco date stamp for 12 months from date of original purchase unless the installation instructions or catalog sets forth a shorter period in which case the shorter period shall apply Seller s obligation shall be limited to repairing or replacing at its option free of charge for materials or labor any product which is proved not in compliance with Seller s specifications or proves defective in materials or workmanship under normal use and service Seller shall have no obligation under this Limited Warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than Ademco factory service For warranty service return product transportation prepaid to Ademco Factory Service 165 Eileen Way Syosset New York 11791 THERE ARE NO WARRANTIES EXPRESS OR IMPLIED OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE WHICH EXTEND BEYOND THE DES
96. ection provides information about final power up procedures and battery size calculations Earth Ground Connections The designated earth ground terminal 21 must be terminated in a good earth ground for the lightning transient protective devices in this product to be effective See the INSTALLING THE CONTROL section earlier in this manual AC Power Up 1 Plug the 1321 TF2 transformer into a 24 hour uninterrupted 120VAC outlet 2 Following power up AC dl disabled or System Busy Alpha keypads or NOT READY fixed word keypads will be displayed Also the green READY LED on the keypad s should light Some keypads are equipped with a POWER LED in place of a READY LED After approximately 1 minute the initial displays will revert to DISARMED READY TO ARM for Alpha keypads or READY for Fixed word keypads if there are no faulted zones This 1 minute delay allows PIRs etc to stabilize To bypass this delay press 0 Note If you do not get the Ready displays described above refer to Trouble Conditions in the SYSTEM OPERATION section and also to the TROUBLESHOOTING GUIDE section Connecting The Back Up Battery In the event of an AC power loss the Control panel is supported by a back up rechargeable gel cell battery The minimum battery size recommended is the No 467 12V 4AH battery See Calculating Battery Size Needed below The battery is installed in the control cabinet The st
97. ecurity system so that alarm signals can still be sent to the alarm monitoring station in the event that the telephone lines are out of order alarm signals are normally sent over the phone lines if connected to an alarm monitoring station Section 1 Section 2 Section 3 Section 4 Section 5 Section 6 TABLE OF CONTENTS GENERAL DESCRIPTION 1 1 INSTALLING THE CONTROL 2 1 Mounting the Cabinet sisi 2 1 Installing the Lock if used oo eee eee eeeeee eee eeeeene eeeeesaeeeeeeaaeeeeeaaeeeeeeaeee eeeaaeeeseaaeeeeeeaeeeeaas 2 1 Installing the Control s Circuit Board Alone or if used With a 4204 4219 or 4229 Module 2 1 Installing Control and RF Receiver Circuit Boards Together in the Cabinet 2 3 Standard Phone Line Connections ceeeeceeeeeseaeeesaaesseeeeseae eeseaeeseneeeeaes 2 3 Wiring the AG Transformer as dire E AAt EEEE E E EAE EES 2 4 Installing the Back Up Battery ss 2 4 Earth Ground Connections usine 2 4 INSTALLING REMOTE KEYPADS ceeeenaees 3 1 Keypads that May Be Used 3 1 Winng tothe e E 3 1 Wiring Run Chart for Devices Drawing AUX Power From the Control 3 1 Mounting the Keypads AA 3 2 Using A Supplementary Power Supply To Power Additional Keypads sssnns0s1101 3 2 Preliminary Check Out Procedure sir 3 3 BASIC HARD WIRED ZONES 5 and 6 tee eeeteeeeeaeeeaees 4 1 Installing the Hard W
98. el you need only plug the transformer in to 120VAC outlet to power up the system 2 Enter the programming mode by keying Installer Code 8 0 Data field 22 RF SYSTEM TYPE must have been programmed for a 5800 RF system before continuing 2 entered in that field 3 24 RF HOUSE ID CODE The House ID identifies a 5827 or 5827BD Wireless keypad if it is used enter 01 31 The wireless keypads should be set to the same ID If no wireless keypad is to be used leave as 00 Enrolling 5800 Transmitters Into The System There are two methods that may be used to enroll transmitters The first method is performed in 56 zone programming mode which is contained in this section and describes how to enroll each transmitter into the system as you are entering the zone information The second method is called sequential mode and uses 83 described in the SEQUENTIAL MODE section later in this manual This section describes how to enroll all the transmitters into the system after all zone information has been entered As an option the zone programming and sequential modes allow you to use a 5803 or 5804 button type transmitter as a program tool The advantage of using a program tool is that it tells the control that you are about to enroll a transmitter into the system You can move to the physical location of the transmitter to be enrolled press the upper left hand button of the program tool and then trip the in
99. en previously enrolled you may enter the enrollment mode now by either entering 1 Yes or by 0 No 1 Yes 0 pressing the upper left hand button of the program tool If using the program tool move to the physical location of the transmitter to be enrolled before pressing the button A single short beep will verify that the button has been pressed The system will respond to the first serial number transmitted after the key on the keypad or the button of the program tool is pressed Enter 0 No if you wish to enroll the transmitter later using the SEQUENTIAL MODE described in Section 14 If 0 No is entered go to step 13 skip steps 11 and 12 11 This prompt is displayed if 1 Yes is entered in response to the Learn S N prompt The serial number may be enrolled by one of two methods es a Enter the 7 digit serial number printed on the transmitter using a Alpha keypad or b Activate the transmitter by faulting or restoring the input you wish to use for that zone e g press a button open or close a door etc 10 Input S N L A002 4064 1 The system will enroll the serial number of the first transmitter heard add the loop number entered to this serial number display the serial and loop numbers and cause the keypad to beep twice l If the serial and loop number combination is already present in the system a single long beep will be heard from the keypad If this happens the system
100. ency Some of the reasons smoke detectors used in conjunction with this System may not work are as follows Smoke detectors may have been improperly installed and positioned Smoke detectors may not sense fires that start where smoke cannot reach the detectors such as in chimneys in walls or roofs or on the other side of closed doors Smoke detectors also may not sense a fire on another level of a residence or building A second floor detector for example may not sense a first floor or basement fire Finally smoke detectors have sensing limitations No smoke detector can sense every kind of fire every time In general detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed violent explosions escaping gas improper storage of flammable materials overloaded electrical circuits children playing with matches or arson Depending on the nature of the fire and or location of the smoke detectors the detector even if it operates as anticipated may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation manual Passive Infrared Detectors do not provide volumetric area protection They do create multiple beams of protection and intrusion can only be detected in unobstructed areas covered by those beams They cannot detect motion or intrusion t
101. enter Alpha descriptors The easiest method requires that you simply enter the 3 digit reference number for the desired word s The 3 digit number for each word is provided in the Alpha Vocabulary list on a following page An alternate method allows you to pick the desired words by scrolling through the Alpha Vocabulary list Programming the Descriptors 1 With the system powered up enter the programming mode by keying Installer code 4 1 1 1 8 0 The following display will appear 2 Press 82 The Program Alpha prompt will appear 3 Press 1 Yes The Custom Words prompt will appear 13 1 4 Press 0 No The system will then automatically display the default descriptor for zone 1 The procedure for adding custom words to the built in vocabulary will be found later under Adding Custom Words Default Descriptor If a descriptor was not entered previously for zone 1 the default descriptor for zone 1 will be dis played Note that no entries can be made Entries can be made only when the display contains a flashing cursor which signifies the entry mode Flashing Cursor system is 5 To delete or change the default ready PE of word descriptor for zone 1 press plus the same zone number 01 This will clear that descriptor and gain access to ZN 01 the entry mode with flashing cursor allowing changes to be made NOTE If you do not wish to change the existing
102. eport or immediately following it the caller should key the following via the keypad on the phone INSTALLER Code 4111 then 1 OFF 6 A beep should be heard and from a wired keypad on the premises and the words DISARMED READY TO ARM or DISARMED NOT READY TO ARM should be heard on the callers phone indicating that the command was entered successfully DISARMED NOT READY TO ARM would indicate an open zone 7 Atthis point the caller can hang up the phone 8 Verify with the caller that there was successful access to the system and that the appropriate annunciations were heard over the phone Section 9 EXTERNAL SOUNDERS This section provides a list of compatible sounders connection information for an external sounder and programming procedures for those options that affect the operation of external sounders Compatible Sounders Ademco AB 12M 10 Motor bell amp box UL Grade A 100mA current Motorized Bell amp Box draw Ademco 1011BE12M Motor bell amp box UL Listed 100mA current draw 10 Motorized Bell amp Box Ademco 702 Self contained 6 12 volt siren driver built in and Outdoor Siren weatherproof for outdoor use Can be wired for either a steady or warble sound 117dB 10 feet 1500mA current draw Ademco 719 Self contained 6 12 volt siren driver built in 2 Channel Siren Steady or warble sound 109dB 10 feet 550mA current draw Ademco 747 Self contained 6 15 volt siren driver b
103. eprogram as necessary Check installation to see if in accordance with established procedure Check programming switches on transmit ter Check with all occupants of protected premises Check setting of entry delay Exit delay is 15 seconds longer than the entry delay time Remind user of same Check all openings for proper switch and magnet orientation Continued TROUBLESHOOTING GUIDE continued SYMPTOM POSSIBLE CAUSE REMEDY 7 Intrusion alarm for no ap parent reason continued 8 Repeated low battery signal 9 Local bell and keypad sound continuously after arming Magnetic contacts improperly connected or wire broken Entry door programmed as Instant Loose fitting door or window being rattled by wind or vibrations Transmitter located where temperature drops below 32 F Poor quality or unspecified battery in transmitter Transmitter malfunctioning 9 Exit or interior zone contained a fault at end of Exit Delay e g Exit door left open The Exit Alarm display etc will also result if an alarm from an exit or interior zone occurs within two minutes after the end of an exit delay ___________ Check wiring connections Be sure wires are properly stripped and are tightly fastened to screw terminals Check and revise programming Re program transmitter number Mount magnet closer to magnet Change location Use magnetic contacts to protect opening
104. es wiring setup programming requirements and a checkout procedure for that device The checkout procedures ensure that the specific device is operational in the system before proceeding to the next section This sectional arrangement is also particularly useful if you are making an addition to the system at a later time e g adding Wireless zones adding a 4285 Phone module etc Without an understanding of the programming method for this system you will not be able to successfully perform the required programming Before any programming is attempted we therefore urge you to read the Mechanics of Programming and the Data Field Descriptions in the separate PROGRAMMING GUIDE that has been supplied If you are an experienced user of Ademco products you may choose to wire and then program the entire system at one time If so refer to Mechanics of Programming and Data Field Descriptions in the separate PROGRAMMING GUIDE after the hardware setup is complete The separate PROGRAMMING GUIDE contains all of the information you will need to program the system including a blank Programming Form except for detailed programming for hardwired zones 5 and 6 hardwired expansion zones and wireless zones which are contained in the following sections in this manual BASIC HARDWIRED ZONES 5 and 6 HARDWIRED ZONE EXPANSION 4219 4229 and WIRELESS RF ZONE EXPANSION 5700 amp 5800 RF SYSTEMS This manual uses various i
105. ese is described below and in the programming procedure for 80 and 81 interactive modes that are provided at the end of this section The control supports the following relay modules 4204 Relay Module 4 relays 4229 Zone Expander Relay Module 2 relays 1 The 4204 and 4229 relays provide Form C normally open and normally closed contacts 2 A 4204 cannot be used if a 4219 or 4229 is already being used In 80 and 81 interactive modes a series of keypad prompts will request entries for programming of the Relay outputs used in the system Refer also to OUTPUT RELAYS WORKSHEET FOR FIELDS 80 AND 81 in the blank programming form provided in the separate Programming Guide manual 4204 and 4229 Relay Modules 4204 4229 Setup The 4204 unit can be mounted either remotely or in the control panel The following steps should be taken to properly set up the 4204 1 Connect the 4204 or 4229 module to the control s remote keypad terminals 4 7 using the connector supplied with the module Use standard 4 conductor twisted cable for long wiring runs 2 Set the 4204 or 4229 s DIP switch for a device address of 1 switch 2 OFF and switches 3 4 and 5 ON Switch 1 determines the unit s cover tamper response ON disabled OFF enabled 3 Connect the desired field wiring to the unit s relay contact terminals See Figures 10 and 11 Supervision The 4204 and 4229 modules are supervised against removal CHECK
106. ether This precaution may be particularly important in rural areas Caution User should not attempt to make such connections themselves but should contact the appropriate electric inspection authority or electrician as appropriate The Load Number LN assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device to prevent overloading The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the Load Numbers of all the devices does not exceed 100 AVIS L tiquette du minist re des Communications du Canada identifie le mat riel homologu Cette tiquette certifie que le mat riel est conforme certaines normes de protection d exploitation et de s curit des r seaux de t l communications Le minist re n assure toutefois pas que le mat riel fonctionnera la satisfaction de l utilisateur Avant d installer ce mat riel l utilisateur doit s assurer qu il est permis de le raccorder aux installations de l entreprise locale de t l communications Le mat riel doit galement tre install en suivant une m thode accept e de raccordement Dans certains cas les fils int rieurs de l entreprise utilis s pour un service individuel la ligne unique peuvent tre prolong s au moyen d un dispositif homologu de raccordement cordon prolongateur t l phonique interne L abonne ne doit pas oubl
107. eut tre constitu e de n importe quelle combinaison de dispositifs pourvu que la somme des indices de charge de l ensemble des dispositifs ne d passe pas 100 APPENDIX B WARNING THE LIMITATIONS OF THIS ALARM SYSTEM While this System is an advanced design security system it does not offer guaranteed protection against burglary fire or other emergency Any alarm system whether commercial or residential is subject to compromise or failure to warn for a variety of reasons For example e Intrusion detectors e g passive infrared detectors smoke detectors and many other sensing devices will not work without power Battery operated devices will not work without batteries with dead batteries or if the batteries are not put in properly Devices powered solely by AC will not work if their AC power supply is cut off for any reason however briefly Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver Even if the signal path has been recently checked during a weekly test blockage can occur if a metal object is moved into the path A user may not be able to reach a panic or emergency button quickly enough While smoke detectors have played a key role in reducing residential fire deaths in the United States they may not activate or provide early warning for a variety of reasons in as many as 35 of all fires according to data published by the Federal Emergency Management Ag
108. fer to the 5800TM s instructions 5700 Series Transmitter Setup Each 5700 series transmitter has DIP switches to set both the transmitter s zone number Transmitter zone ID and the system House ID The House ID will be the same for all transmitters and must match the House ID programmed into the system in data field 24 for the wireless receiver This can be likened to a family in which everyone has the same last name House ID but each person has a different first name Transmitter zone ID The zone ID number must then be programmed into the system using 56 interactive mode A variety of wireless transmitters can be used to make up the wireless zones These include window door units smoke detectors PIRs and panic buttons Zone ID number assignments can be from 10 63 Remember the 5700 system supports up to 8 wireless zones depending on the RF receiver used see Table 1 previously Setting the DIP Switches on 5700 Series Transmitters Set the DIP switches on each 5700 series transmitter to the appropriate zone ID number and House ID Refer to the Compatible 5700 Series Transmitters table on a following page in this section for zone numbers and programming information for each particular transmitter Refer also to DIP SWITCH TABLES FOR 5700 RF WIRELESS DEVICES later in this section S The House ID allows the 5700 RF system to identify 5700 transmitters with a matching House ID If using a 5700 RF wireless system the
109. for wired expansion zones Values in the summary display are the currently programmed values To start programming zone 10 press A prompt for Zone Type will appear Zone Number Each zone must be assigned a zone type which defines the way in which the system responds to faults in that zone A detailed explanation of each zone type is provided in Response Type Definitions in the in the separate Programming Zone Type 03 entry shown T Guide Enter the desired zone type from the list below 00 Zone Not Used 06 24 Hr Silent 01 Entry Exit 1 07 24 Hr Audible 03 Perimeter 08 24 Hr Aux 04 Interior Follower 09 Fire 05 Trouble Day Alarm Night 10 Interior w Delay 23 No Alarm Response When the display shows the zone type you want press to continue The report code consists of 2 hexadecimal digits each in turn consisting of 2 numerical digits For example for a report code of 3C enter 0 3 for 3 and 1 2 for C Refer to the SYSTEM COMMUNICATION section for com plete information on report codes if necessary Enter the report code and then press to continue At the INPUT DEVICE prompt enter 2 AUX Wired as the input device The display on the left will appear Press to continue 10 Input Dev LP AUX WIRED AW 01 Typical summary display A summary display will appear showing the Zn ZT RC In L data for the zone that was just programmed 10 03
110. from each of the transmitters the zone number of that transmitter will disappear from the display The transmitter codes may be checked upon installation or in an installed system All the wireless zone numbers should disappear after about 1 1 2 hours Note Any transmitter that is not properly entered into the system will not turn off its zone number Exit the Transmitter Sniffer mode by keying Installer code OFF GO NO GO TEST MODE By keying Installer code 4 a mode similar to the test mode is entered but the wireless receiver gain is reduced Checking in this mode not only assists in determining good mounting locations for the transmitters when the system is being installed but also verifies that the RF transmission has sufficient signal amplitude margin for the installed system 1 Enter the Installer Code 4 2 Once transmitters are placed in their desired locations and the approximate length of wire to be run to sensors is connected to the transmitter s screw terminals fault each transmitter Do not conduct this test with your hand wrapped around the transmitter as this will cause inaccurate results e The keypad will beep three times to indicate signal reception e If the keypad does not beep re orient or move the transmitter to another location Usually a few inches in either direction is all that is required 3 Exit the GO NoGo mode by keying Installer code OFF TO THE INSTALLER Regular maintenance a
111. from the alarm output terminals cannot exceed 2 Installations amps The back up battery must be installed since this current is supplied by that battery I Going beyond the limits indicated 2 amps will overload the power supply or may cause the electronic circuit protecting the sounder output to trip This control complies with NFPA requirements for temporal pulse sounding of fire notification appliances Temporal pulse sounding for a fire alarm consists of the following 3 pulses pause 3 pulses pause 3 pulses repeated Sounder Connections The VIA 30PSE provides a 12 VDC output which can power external alarm sounders bells or sirens see compatible sounders listed previously This output will activate a sounder when an alarm occurs Make connections to alarm output terminals 3 and 4 See Figure 13 CONTROL BOARD No 702 SIREN ALARM OUTPUT Figure 13 Typical Sounder Wiring Programming for External Sounders 1 With at least one 2 line Alpha keypad 5137AD or 6139 connected to the keypad terminals on the control power up the system temporarily If you had previously connected the AC transformer to the control panel you need only plug in the transformer to 120VAC outlet to power up the system 2 Enter the programming mode by keying the following on the Alpha keypad INSTALLER code 4 1 1 1 8 0 3 Press 28 Single Alarm Sounding per Zone Armed Period Enter 1 f
112. g is to be used Note The maximum number of alarm and alarm restore reports during one armed period is determined by field 92 Press 47 SPLIT DUAL REPORTING Enter 0 to disable Backup report only This is the default TO PRIMARY PHONE No TO SECONDARY PHONE No 1 Alarms Restore Cancel Other Reports 2 All except Open Close Test Open Close Test 3 Alarms Restore Cancel All reports 4 All except Open Close Test All reports 5 All reports All reports TO PRIMARY PHONE TO PAGING NUMBER 6 Allreports except Open Close Alarms Open Close Troubles 7 All reports Alarms Troubles 8 All reports Alarms Open Close Troubles 9 Allreports except Open Close Alarms Open Close for User Nos 5 25 Troubles Will report only Users 5 8 If using wireless button type devices the zone number of the arm or disarm button 10 25 will be sent as the user number Entries 6 through 9 will send a report to a pager in addition to the selected primary phone number but you must enter the pager number as the secondary phone number in field 42 A 10 digit code is sent to the pager which will take the following format t 4 digit Subscriber No gt SSSS EEE NNN lt 3 digit User or Zone No as entered in field 43 T 3 Digit Event Code as follows 911 Alarm NNN Zone No 001 Open System disarmed NNN User No 002 Close System armed NNN
113. g mode by keying 99 10 1 10 2 Section 11 AUDIO ALARM VERIFICATION AAV UNIT General Information An Audio Alarm Verification AAV module such as the Eagle 1241 is an add on accessory that permits voice dialog between an operator at a central station and a person at the alarm installation for the purpose of alarm verification Alarm reports must be programmed for the primary phone number to enable this feature AAV should not be used when Paging or Alarm Reports are being sent to a Secondary number If this is done the call to the Secondary number by the communicator after the alarm report will prevent the AAV from taking control of the telephone line and the AAV Listen in session cannot take place The AAV option cannot be used in UL installations After all messages have been sent during a reporting session to the primary phone number the control will trigger the AAV if at least one of the messages was an alarm report If Contact ID format is selected for the primary phone number the control will send a listen in to follow message event code 606 which signals the 685 receiver at the central station to hold the phone connection for 1 minute Once the digital message is kissed off the control will give up the phone line to the AAV module without breaking connection with the central station At this time all sirens and all continuous keypad sounds will be shut off
114. gned zone in the zone list e TROUBLE Relay action begins upon any trouble condition in an assigned zone in the zone list e NOT USED Relay action is not dependent upon one of the above events 2 B STOP STP A B ZONE LIST ZL is a group of zones to which the EVENT applies in order to activate a particular relay Note that there are a total of 3 zone lists that can be programmed in field 81 mode when the selected EVENT Alarm Fault or Trouble occurs in any zone in the selected Start ZONE LIST 1 2 or 3 activation of the selected relay will START 1 ZONE TYPE SYSTEM OPERATION ZT If a System Operation such as DISARMING or ANY FIRE ALARM is to activate the relay the appropriate choice would also be entered under the ZONE TYPE option ZONE TYPE is used independently of the EVENT ZONE LIST combination If a specific ZONE TYPE is chosen any zone of that re sponse type going into alarm trouble or fault will cause the relay to activate as selected in ACTION If the same ZONE TYPE is also chosen for the STOP programming any zone of that type that restores will de activate the relay If a SYSTEM OPERATION is chosen eg End of Exit Time that operation will cause the relay to activate as selected in ACTION The different choices for ZONE TYPE and SYSTEM OPERATION are listed in Programming Output Relays later in this section and in the Programmi
115. hat takes place behind walls ceilings floors closed doors glass partitions glass doors or windows Mechanical tampering masking painting or spraying of any material on the mirrors windows or any part of the optical system can reduce their detection ability Passive Infrared Detectors sense changes in temperature however as the ambient temperature of the protected area approaches the temperature range of 90 to 105 F 32 to 40 C the detection performance can decrease Alarm warning devices such as sirens bells or horns may not alert people or wake up sleepers if they are located on the other side of closed or partly open doors If warning devices are located on a different level of the residence from the bedrooms then they are less likely to waken or alert people inside the bedrooms Even persons who are awake may not hear the warning if the alarm is muffled by noise from a stereo radio air conditioner or other appliance or by passing traffic Finally alarm warning devices however loud may not warn hearing impaired people Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or temporarily out of service Telephone lines are also subject to compromise by sophisticated intruders Even if the system responds to the emergency as intended however occupants may have insufficient time to protect themselves from the emergency situation In the case of a monitored alarm sy
116. he following The defaults for individual panic keys or panic key pairs are Zone 07 amp or B zone type 06 24 hr silent Zone 95 1 amp or A zone type 00 not used Zone 96 3 amp or C zone type 00 not used Panic keys are programmed or re programmed by keying the zone number e g 07 95 and 96 and entering the desired zone type that will provide the desired panic function for each of these keys using the list of zone types below 06 24 Hr Silent 07 24 Hr Audible 08 24 Hr Aux 09 Fire Special Notes on Zone Programming When you have programmed all the hard wired zones and Panic keys satisfactorily exit 56 interactive mode at the Enter Zn Num prompt by entering 0 0 as the next zone number Then exit the programming mode by keying 99 See the special notes below then proceed to the check out procedure that follows In field 56 at the summary line for each zone the entered values can be checked If you wish to change anything press to move to the previous entry Press a number of times to move to earlier entries Press to move to later entries again Zone entries can be reviewed by pressing 5 6 Changes cannot be made here so this is safer for review Enter the first zone number to be viewed and press To view each zone press and the zone number will advance to the next programmed zone When the end of the list is reached press 0 0 to exit
117. ier qu il est possible que la conformit aux conditions nonc es ci dessus n emp che pas la d gradation du service dans certaines situations Actuellement les entreprises de t l communications ne permettent pas que l on raccorde leur mat riel aux prises d abonn s sauf dans les cas precis pr vus par les tarifs particuliers de ces entreprises Les r parations du mat riel homologu doivent tre effectu es pas un centre d entretien canadien autoris d sign par le fournisseur La compagnie de t l communications peut demander l utilisateur de d brancher un appareil la suite de r parations ou de modifications effectu es par l utilisateur ou cause de mauvais fonctionnement Pour sa propre protection l utilisateur doit s assurer que tous les fils de mise en terre de la source d nergie lectrique des lignes t l phoniques de r seau de conduites d eau s il y en a soient raccord s ensemble Cette pr caution est particuli rement importante dans les r gions rurales Avertissement L utilisateur ne doit pas tenter de faire ces raccordements lui m me il doit avoir recours un service d inspection des installations lectriques ou un lectricien selon le cas L indice de charge IC assign chaque dispositif terminal pour viter toute surcharge indique le pourcentage de la charge totale qui peut tre raccord un circuit t l phonique boucl utilis par ce dispositif La terminaison du circuit boucl p
118. ighest signal priority Transmitter IDs 62 and 63 are unsupervised to allow removal of the 5701 off premises signal priority is lower than that of fire but higher than burglary 1 Transmitters set for zone IDs 48 55 FIRE will transmit once every 12 seconds while the zone is faulted Transmitters set for zone IDs 56 63 will transmit once every 3 seconds while faulted These two ranges of zone ID numbers have high signal priority and their frequent transmissions while faulted ensure re triggering of the alarm until the cause is removed Bear in mind that because of this transmitter battery life could be shortened 2 Transmitters set for an zone IDs of 32 through 47 will have a 3 minute lock out between transmissions Use this range of zone ID numbers for sensors protecting frequently used doors or windows to conserve battery life 3 Refer also to Compatible 5700 Series Transmitters on a following page DIP SWITCH TABLES FOR 5700 RF SYSTEM WIRELESS DEVICES HOUSE ID 5701 PANIC TRANSMITTER 5706 5707 SMOKE 5775 PIR SWITCH SETTING FOR ALL DETECTORTRANSMITTER DETECTOR TRANSMITTER DEVICES EXCEPT 5716 SUSE IDA OWN oF MIRROR DEVICE DIP SWITCH POSITION FT 23456 SIDE 3 5 VIEW UP uP oF I il il f i pa HOUSE ID 1 SHOWN y a te toe tt UP DN VIEW UP 2 3 4 5 6 7 8 9 10 UP TP POS 6 UP XMTR ID 62 HH DN XMTR ID 8S HOUSE ID 1 SHOWN SIDE GES VIEW UP XMTR ID SS 5727 KEYPAD 7234 5 678 32
119. ing 80 this screen will appear Enter the Relay Number 01 02 03 or 04 for a 4204 or 00 to end these entries Press the key to continue The key is used to accept an entry and advance to the next prompt The key is used to revert back to the last question to check or change an entry Press to go forward again This screen displays a summary of the current Relay START programming for this example relay 02 has been selected Press the key to continue This screen displays a summary of the current Relay STOP programming Press the key to continue Enter the desired relay action as listed below Press the key to continue 0 No response 2 Close and Stay Closed 1 Close for 2 seconds 3 Continuous Pulse on amp off 1 sec ON 1 sec OFF Enter the event to START the relay 0 Not used 2 Fault 1 Alarm 3 Trouble A zone list must be used in conjunction with an event If a zone type system operation is to be used instead of an event enter 0 Press the key to continue If a zone list will be used to START the relay action enter the zone list number to be programmed in field 81 1 2 or 3 If not used enter 0 Press the key to continue 02 AEN ZL ZT STT 0 0 O 00 If a zone type or system operation will be used to START the relay action enter the appropriate two digit code see table that follows If not enter 00 Press the key to continue CHOICES
120. ing the Descriptors ss 13 1 Alternate Method for Programming Zone Descriptors cceeeeeeteeeeeeeeae ceeeeenaeeeeeeaaes 13 3 Adding Custom Words 13 4 Alpha Vocabulary List For Entering Zone Descriptors AA 13 5 Character ASCII Chart us iii 13 5 SEQUENTIAL MODE For 5800 Series Wireless Transmitters 14 1 SYSTEM COMMUNICATION seeaeeeeneeesaees 15 1 Report Code Formats iii 15 1 Table of Contact ID Event Codes 15 3 Communication Programming us 15 3 TESTING THE SYSTEM us 16 1 Test Procedure RANNER LO Pages lagon el ee 16 1 TONE Installer eege caine ee E EE EE M AE EP EE 16 2 SYSTEM OPERATION 17 1 Security Codes EE 17 1 Installer Code e deed Seed geed ed date ue 17 1 Assigning the Master Code cccsceeeseeceeeeee caeeeeneeseneeecaeeesaaeeseeees caeeesaeeseaeeeeaes 17 1 Changing the Master Code c cccecceceeeceeeeceee ceceaeeeaeeeeaeeseeeeseeeesaae seaaeeeeaeeeeeeeeaas 17 1 User Code seis nation elites ayia eee cru ed deal tina 17 1 Duress ele EE 17 1 Keypad FUnCtIOns einen din element diem dite inntin nel 17 2 EEN ETH en le 17 2 AMING Riede 17 2 Sie 17 3 4285 Phone module use 17 3 Relays Outputs if used standin tied la aani acetal 17 3 Exit Alarm Displays if programmed s ssessseessseeessrnsssrnsseserrssinnssinnnsrinssrensnrnnnst aens 17 3 Trouble Gonditions ios andere bead raid ee
121. ing the system in the STAY or AWAY mode or disarming of the system depending on the selection made A button programmed for these functions will report the zone number of the button as the user number that armed disarmed to the central station Press to continue 7 Enter the report code The report code consists of 2 hexadecimal digits 10 ReportCode each in turn consisting of 2 numerical digits For example for a report lst 03 2nd 12 3C code of 3C enter 0 3 for 3 and 1 2 for C Refer to the SYSTEM COMMUNICATION section for more information about report codes and report code formats Press to continue 8 Enter the transmitter input device type as follows 3 RF supervised RF transmitter 4 UR unsupervised RF transmitter 5 BR button type RF transmitter unsupervised Refer to the separate Programming Guide for input types Press to continue 10 Input Dev LP Rf Trans RF 1 10 Input Dev 9 The cursor should now be flashing above the loop number The default p is 1 To accept this press If a different loop number is being used RF Trans RF 1 on this transmitter enter the loop number 1 4 and press to continue see the loop designations for various transmitters in the separate Programming Guide The loop number must be entered here whether using Zone Programming or Sequential Mode to enroll transmitters 10 Learn S N 10 If the transmitters serial number has not be
122. ired ZONES cceceeeeeeeeeeeeeeee ceeeeeaeeeeeaaeeeeneaeeeeeeaaeee ceaaeeeenenaeeeeeaaes 4 1 Common Characteristics For Zones 5 and 6 cscesesceceeeeeeeeeeeee ceeeeeeeseeeeeeaeeeeaeeee 4 1 Wiring Burglary and Panic Devices to Zones 5 and 6 eeeteeeeeenaeeeenes 4 1 Wiring 4 Wire Smoke Combustion Detectors on Zones P 4 1 Compatible 4 Wire Smoke Combustion Detectors c ccccsecceceesteeee sesteeeeessneeeeees 4 2 Programming Hard Wired Zones 4 2 Programming Panic Keys eeeeeeeeseeeaeeseeaaeees 4 3 Check Out Procedure for Hard Wired Zones 5 and 6 ccseeeeeeeeeeeeeeeee ceseeeeeeeeneeeees 4 4 WIRED ZONE EXPANSION 4219 4229 ccccscsceeesceeeeueeeeeeeeeeeeeeeeeeeenens 5 1 Installing Zone Expansion Units ss 5 1 Connections and Setup iii 5 1 Programming Wired Expansion Zones A 5 2 Check Out Procedure for Wired Expansion Zones 5 3 WIRELESS RF ZONE EXPANSION 5700 amp 5800 RF SYSTEMS 6 1 Wireless Systems Available cccccccccceeeeeeees ceeeeeeecaeeeeaeeseeeeecaeeeea aeseeeeeseaeeesaeeneneeee 6 1 Wireless System Operation and Transmitter Supervision 6 1 Transmitter Battery CN 6 2 Receiver Supervision iii 6 2 Installation and Setup of the 4281 5881 Series Wireless Receivers 6 2 Installing the 5800TM Module ee eeeeceeeeeeeeeee ceneeeeeeeneeeeeseeeeeeseeeeeee ceeeeeeseeeaeeeeeeeaeees 6 3 5700 Series Transmitter Setup
123. is report is random with up to a 48 minute delay The Restore report has a random delay of up to about 12 minutes If AC restores before the report goes out there is no AC restore report LOW BAT REPORT CODE This will be sent when a low battery condition exists in the system s standby battery connection to the standby battery is checked every 3 minutes CSFM requirement TEST REPORT CODE This is sent periodically to test that the communicator and phone lines are operational frequency of report is selected in field 51 OPEN EXIT ALARM REPORT CODE 1st DIGITS Open Report Code To enable enter a code or 0 to disable in the left hand box For expanded or 4 2 reporting 2nd digit User Exit Alarm Report Code To enable enter a code or 0 to disable in the right hand box If enabled any alarm from an exit or interior zone occurring within two minutes after the end of the exit delay will send a special message indicating exit alarm to the central station and a zone indication and Exit Alarm or EA is displayed on the keypad If an exit or interior zone contains a fault as the exit delay ends the local bell and keypad sound continuously a Ifthe subscriber then disarms the system before the ensuing ENTRY delay ends no message is transmitted to the central station but a zone indication and Canceled Alarm or CA is displayed on the keypad b Ifthe system is not disarmed before that entry delay ends a special mess
124. it Master Code Note The Master Code is defined as User 2 In normal operation mode the Master code can be changed by entering Master Code 8 2 New Master Code New Master Code again In normal operation mode the Master security code can be used to assign up to 4 secondary 4 digit security codes It can also be used to remove sec ondary codes from the system individually To assign or change a Secondary security code enter via keypad Master Code CODE key User 3 6 desired 4 digit Secondary Code The system will emit a single beep when each secondary code has been suc cessfully entered To delete a Secondary security code enter via keypad Master Code CODE key User 3 6 e All Master and Secondary security codes permit access to the system for arming disarming etc s f a secondary code is inadvertently repeated for different users the lower user number will take priority e Opening and closing reports are sent for the Master code as No 02 with the appropriate subscriber number Secondary user codes are sent as Nos 3 through 6 respectively with the appropriate subscriber number This feature is intended for use when you are forced to disarm or arm the system under threat When used the system will act normally but can silently notify the central station of your situation if that service has been provided The Duress code may be any 4 digit cod
125. ive one or two 702 series connected self contained 20 watt sirens Do not connect two 702s in parallel AUXILIARY POWER OUTPUT 12VDC 500mA max Interrupts for 4 wire smoke detector reset Note For UL installations Alarm Sounder plus Auxiliary Power currents should not exceed 600mA total STANDBY TIME see Table in the FINAL POWER UP section FUSE Battery 8A No 90 12 3 Communication FORMATS SUPPORTED Ademco Express 10 characters sec DTMF Touch Tone Data Tones 1400 2300Hz ACK 1400Hz KISSOFF Ademco Contact ID Reporting 10 characters sec DTMF Touch Tone Data Tones 1400 2300Hz ACK 1400Hz KISSOFF Ademco Low Speed 10 pulses sec 1900Hz Data Tone 1400Hz ACK KISSOFF Radionics SESCOA 20 pulses sec 1800Hz Data Tone 2300Hz ACK KISSOFF Can report 0 9 BF Line Seize Double Pole Ringer Equivalence 0 7B FCC Registration No AC 398U 681 92 AL E 4 Maximum Zone Resistance Zones 5 and 6 300 ohms excluding EOLR 5 Zone Response Zones 5 and 6 300 500 msec 4127 1 Physical 5 5 8 W x 4 11 16 H x 7 8 D 143mm x 119mm x 22mm REMOTE KEYPAD 2 Electrical Voltage Input 12VDC Current Drain 20mA 3 Interface Wiring To control panel s keypad connection points RED 12VDC input aux power GREEN Data Out to Control YELLOW Data In from Control BLACK Ground 4137AD amp 5137AD 1 Physical 8 2 5 W x 4 3 4 H x 1 1 10 D 213mm x 121mm x 28mm BEMOTE KEYRAD 2 Electrica
126. l Voltage Input 12VDC Current Drain 60mA 4137AD 90mA 5137AD 3 Interface Wiring Same as 4127 19 1 6127 REMOTE KEYPAD 6128 REMOTE KEYPAD 6137 REMOTE KEYPAD 6138 amp 6139 REMOTE KEYPADS 4281L 4281M 4281H RF RECEIVERS 5700 System and 5881L 5881M 5881H RF RECEIVERS 5800 System 5800TM TRANSMITTER MODULE used with 5827BD Wireless 2 Way Keypad 4219 WIRED EXPANSION MODULE 4229 WIRED EXPANSION RELAY MODULE 4204 RELAY MODULE UNa o nD on ech O no ech Wi A Physical 5 3 4 W x 4 3 4 H x 1 D 146mm x 121mm x 26mm Electrical Voltage Input 12VDC Current Drain 20mA Interface Wiring Same as 4127 Physical 5 3 4 W x 4 3 4 H x 1 D 146mm x 121mm x 26mm Electrical Voltage Input 12VDC Current Drain 30mA Interface Wiring Same as 4127 Physical 6 1 4 W x 4 3 4 H x 1 D 159mm x 121mm x 26mm Electrical Voltage Input 12VDC Current Drain 85mA Interface Wiring Same as 4127 Physical 6 1 4 W x 4 3 4 H x 1 D 159mm x 121mm x 26mm Electrical Voltage Input 12VDC Current Drain 100mA Interface Wiring Same as 4127 Physical 7 3 8 188mm W x 4 3 8 112mm H x 1 7 16 37mm D Note 10 7 8 277mm H with antenna Electrical Voltage Input 12VDC Current Drain 35mA Interface Wiring Same as 4127 Range 200ft 60m nominal indoors from wireless transmitters the actual range to be determined with sys
127. l Voltage Input 12VDC Current Drain 150mA Device Address Set to address 3 Interface Wiring Same as 4127 above Accessories Compatible Devices No 1321 16 5VAC 25VA Plug In Transformer in U S A No 1321CN 16 5VAC 25VA Plug In Transformer in Canada Sounders Ademco AB 12M 10 Motor bell amp box UL Grade A 100mA current Motorized Bell amp Box draw Ademco 1011BE12M 10 Motor bell amp box UL Listed 100mA current Motorized Bell amp Box draw Ademco 702 Outdoor Self contained 6 12 volt siren driver built in Siren and weatherproof for outdoor use Can be wired for either a steady or warble sound 117dB 10 feet 1500mA current draw Ademco 719 Self contained 6 12 volt siren driver built in 2 Channel Siren Steady or warble sound 109dB 10 feet 550mA current draw Ademco 747 Self contained 6 15 volt siren driver built in for Indoor Siren indoor wall mount 747F available for flush mounting 105dB 10 feet 400mA current draw Ademco 747UL Self contained 6 15 volt siren driver built in for Indoor Siren indoor wall mount UL Listed 85dB 10 feet 320mA current draw Ademco 744 6 jumper selected sound outputs Rated at 119dB with use of an 8 ohm 30 watt speaker Siren Driver 1 3 amps current draw Ademco 745X3 12 volt voice siren driver with English Spanish Voice Siren Driver and French voice messages Separate messages for Fire and Burglary Use with 8 ohm speaker UL Listed
128. licable if the 4285 Phone regarding phone line connections which are different than those shown here Incoming phone line and handset wiring is connected to the main terminal block via a RJ31X jack as indicated below and shown in Figure 4 Term 17 Local Handset TIP Brown Term 18 Local Handset RING Gray Term 19 Incoming Phone Line TIP Green Term 20 Incoming Phone Line RING Red Colors of wires in Direct Connect Cord Incoming Handset Telco Line TERMINALS ON CONTROL 4 EARTH GROUND INCOMING TELCO LINE SI D GROUND BROWN TIP E CH M 5 y PREMISES PHONES Figure 4 Standard Telephone Line Connections 2 3 Wiring The AC Transformer Installing No 1321 Wire the No 1321 transformer to terminals 1 and 2 on the control board See wiring table below for wire gauge to use WIRING TABLE Distance of Transformer Wire Gauge From the Conirol Panel To Use Up to 50 feet 20 50 100 feet 18 100 250 feet 16 S Wiring to the AC Transformer must not exceed 250 feet using 16 gauge wire Do not plug the transformer into the AC outlet until you are instructed to do so later in the manual The Back Up Battery wh Do not attach the connector cable to the battery terminals until you are instructed to do so later in the manual 1 Place the 12 volt back up battery in the control cabinet 2 Attach
129. ly conduct Go No Go tests to verify 5700 5800 adequate signal strength and reorient or relocate transmitters if necessary RF Systems During this mode wireless receiver gain is reduced by 50 Testing in this mode assists in determining good mounting locations for the transmitters and verifies that the RF transmission has sufficient signal amplitude margin for the installed system 1 Enter the Installer Code 4 2 Once transmitters are placed in their desired locations and the approximate length of wire to be run to sensors is connected to the transmitter s screw terminals fault each transmitter Do not conduct this test with your hand wrapped around the transmitter as this will cause inaccurate results e The keypad will beep three times to indicate signal reception e If the keypad does not beep re orient or move the transmitter to another location Usually a few inches in either direction is all that is required 3 Mount the transmitter according to the instructions provided with the transmitter 4 Exit the GO NO GO test mode by entering Installer Code OFF Section 7 RELAY OUTPUT DEVICES Relay Device Basics Relays are programmable switches that can be used to perform many different functions They can be used to turn lights on and off control sounders or for status indications In this system each relay must be programmed as to how to act ACTION when to activate START and when to deactivate STOP Each of th
130. m Communication Formats Supported e Ademco Low Speed Standard or Expanded e Sescoa Radionics Standard or Expanded e Ademco Express e Ademco Contact ID Zone Descriptors You can assign Alpha descriptors to all zones useful only when using Alpha keypads and or the 4285 Phone module 1 2 Section 2 INSTALLING THE CONTROL This section provides instructions for mounting the control cabinet and installing the cabinet lock if used Also included in this section are instructions for the following e Installing the main PC board and 4204 Relay Unit if used e Mounting the RF Receiver board if used in the cabinet e Standard phone line connections e Installing the back up battery in the cabinet e Connecting the AC transformer e Making earth ground connections Mounting the Cabinet Mount the control cabinet to a sturdy wall using fasteners or anchors not supplied in a clean dry area which is not readily accessible to the general public Four mounting holes are provided at the back of the cabinet If an RF Receiver is being used and you intend to mount its PC board within the cabinet note the following e Do not mount the cabinet on or near metal objects This will decrease RF range and or block RF transmissions from wireless transmitters e Do not locate the cabinet in an area of high RF interference revealed by frequent or prolonged lighting of the LED in the receiver after it is operational Ran
131. n program these zones individually in 56 interactive mode as indicated in Programming Wired Expansion Zones later in this section Connections 1 Connect the 4219 or 4229 module to the control s keypad terminals see and Set Up diagram below 2 Set the 4219 or 4229 s DIP switch for device address 1 switch 2 OFF and switches 3 4 5 ONT Switch 1 determines expansion zone A s response time ON normal response OFF fast response For location of the DIP switch in the unit see the diagram below location of DIP switch for both units is in the same location For additional information see instructions supplied with the 4219 and 4229 DIP SWITCH FOR SETTING ADDRESS I AND ZONE A RESPONSE RELAY CONNECTOR EITHER OR BOTH CAN BE USED TERMINALS ON CONTROL PANEL 4 PIN CONSOLE PLUG E S GRN DATA OUT TAMPER JUMPER POSITION TO CONTROL 2 TERM 6 4229 IN CABINET ae NOT TAMPERED o 4 GROUND TERM 4 Tir o 4229 REMOTE gt zo o TAMPER PROTECTED TBI og UE SE de e YEL DATA IN Z oji gt TERM7 ele CONTROL RLY i REED TERMINATE EACH on ge rine eee RELAY H PLAYS SWITCH END OF LINE RESISTOR EACH ZONE S MAX LOOP RESISTANCE 300 OHMS E 0 L ZONES A B C D E F G H Figure 8 Wiring Connections 4219 amp 4229 4229 shown Programming Wired Expansion Zones 1 Wi
132. n all transmitters set for the same ID If using a 5827BD wireless keypad the House ID also applies Note The 5827BD is keypad programmable the 5727 wireless keypad is programmed via its DIP switches Refer to the instructions supplied with the 5827BD and 5727 for details Batteries should be installed in all transmitters Using the House ID Sniffer Mode 5700 Systems 4281 series RF receivers respond only to 5700 transmitters and 5827BD wireless keypads set to the same House ID 01 31 programmed into the control panel This prevents system interference from transmitters in other nearby systems Using the House ID Sniffer Mode will make sure you have not chosen a House ID that is in use in a nearby system 1 Enter your Installer Code 2 2 The receiver will now sniff out any House IDs in the area and display them Keep the receiver in this mode for about 2 hours to give a good indication of the House IDs being used Be sure you have used a House ID that is not displayed 3 To exit the Sniffer Mode simply enter your Installer Code OFF wh Since the Sniffer Mode effectively disables wireless point reception Sniffer Mode cannot be entered while the system is armed S Do not permanently mount the transmitters yet a Go No Go test described later must be performed after programming is completed to make sure reception of each transmitter s signal at the proposed mounting location is adequate Zone
133. n control and a zone expander or wireless receiver is interrupted Check the wiring and DIP switch settings on the units e If there are wireless sensors in the system the CHECK condition may also be caused by some change in the environment that prevents the receiver from receiving signals from a particular sensor e A display of BAT Fixed word keypads or SYSTEM LO BAT Alpha keypads with no zone number indicates that the system s main standby battery is weak s A display of BAT Fixed word keypads or LO BAT Alpha keypads with a zone number and a once per minute beeping at the keypad indicates that a low battery condition exists in the wireless sensor displayed zone 00 indicates a wireless keypad If the battery is not replaced within 30 days a CHECK display may occur Note Some wireless sensors contain a non replaceable long life battery which requires replacement of the entire unit at the end of battery life e g Nos 5802 5802CP 5803 e If there is no keypad display at all and the POWER indicator if present is not lit operating power for the system has stopped and the system is inoperative Note The control panel will power up in its previous state armed or disarmed after a complete power failure but will not retain any memory of bypasses e If the message AC LOSS Alpha keypads or NO AC Fixed word keypads is displayed and the POWER indicator if present is off the keypad is operating
134. nd inspection at least annually by the installer and frequent testing by the user are vital to continuous satisfactory operation of any alarm system The installer should assume the responsibility of developing and offering a regular maintenance program to the user as well as acquainting the user with the proper operation and limitations of the alarm system and its component parts Recommendations must be included for a specific program of frequent testing at least weekly to insure the system s proper opera tion at all times 16 2 Section 17 SYSTEM OPERATION Security Codes Installer Code Assigning the Master Code Changing the Master Code User Codes Notes Duress Code Important This code is useful only when the system is connected to a central station The installer programs the 4 digit Installer Code initially as part of the programming procedure The factory default Installer code is 4 1 1 1 but may be changed in field 20 Note The Installer Code is defined as User 1 The Installer code is the only code that can allow re entry into programming mode In normal operation mode only the Master code can be used to enter the User codes refer to Assigning the Master Code See MECHANICS OF PROGRAMMING section in the PROGRAMMING GUIDE manual for details on exiting the programming mode via 98 or 99 In normal operation mode assign the 4 digit Master Code as follows Installer Code 8 2 4 dig
135. ng Form in the separate Programming Guide The STOP programming determines when and under what conditions the relay will be de activated The following options are available 1 RESTORE ZONE LIST ZL If a ZONE LIST is used as the Stop event the relay will de activate when all the zones in that list restore from a previous fault trouble or alarm condition This will occur regardless of what is programmed to START the relay therefore a RESTORE ZONE LIST would normally only be used when a ZONE LIST is used to start the relay 1 ZONE TYPE SYSTEM OPERATION ZT Instead of using a RESTORE ZONE LIST a specific zone response type or system operation action can be selected to de activate the relay If a specific ZONE TYPE is chosen any zone of that response type that restores from a previous alarm trouble or fault condition will cause the relay to de activate If a SYSTEM OPERATION is chosen that operation will cause the relay to de activate The different choices for ZONE TYPE and SYSTEM OPERATION are listed in Programming Relays later in this section and in the Programming Form If relay outputs are used two keypad entries available to the user are included among the system operation choices 34 and 35 that may be programmed They can manually activate or de activate the relay s for starting or stopping some action such as turning lights on or off etc These entries are Security Code
136. now be used refer to the CHARACTER ASCI LIST of letters numbers and symbols on a following page Method 1 Press the key followed by the two digit entry for the first letter you would like to display e g 6 5 for A or Method 2 Use the 3 key to advance through the list of symbols numbers and letters Use the 1 key to move back through the list When you have reached the desired character press 6 to select it The cursor will then move to the right in position for the next character Repeat steps 3 and 4 to create the desired word s Note that the 4 key can be used to move the cursor to the left if necessary and that key 7 can be used to enter a blank or erase an existing character Remember no word or word string can exceed 10 characters Press the 8 key to save the custom word s and return to the CUSTOM WORD display Repeat steps 2 5 for other custom words to be entered To change a custom word just overwrite it If no more are to be entered now press 0 to return to the Descriptor entry The custom word s will be automatically added to the built in vocabulary When zone descriptors are being entered as described in step 6 of Programming the Descriptors the custom word numbers are 250 to 254 for words 1 to 5 respectively When being entered as described in step 3 in Alternate Method For Programming Zone Descriptors each word will be found at the end of the group of words that begin
137. nstall a smoke detector inside every bedroom where someone sleeps with the door partly or completely closed Smoke could be blocked by the closed door Also an alarm in the hallway outside may not wake up the sleeper if the door is closed e Install a smoke detector inside bedrooms where electrical appliances such as portable heaters air conditioners or humidifiers are used e Install a smoke detector at both ends of a hallway if the hallway is more than 40 feet 12 meters long e Install smoke detectors in any room where an alarm control is located or in any room where alarm control connections to an AC source or phone lines are made If detectors are not so located a fire within the room could prevent the control from reporting a fire or an intrusion KITCHEN A A KITCHEN DINING DINING LIVING ROOM BEDROOM M Smoke Detectors for Minimum Protection Smoke Detectors for Additional Protection A Heat Activated Detectors A CLOSED GARAGE DOOR THIS CONTROL COMPLIES WITH NFPA REQUIREMENTS FOR TEMPORAL PULSE SOUNDING FOR FIRE NOTIFICATION APPLIANCES Recommendations For Proper Intrusion Protection For proper intrusion coverage sensors should be located at every possible point of entry to a home or commercial premises This would include any skylights that may be present and the upper windows in a multi level building In addition we recommend that radio backup be used in a s
138. ode 2 Then enter the zone number and press repeatedly until the cursor is under the RF Input Loop L position This is the specific input loop or button on the transmitter that has been entered for that zone 3 Enter a 0 at this point then press 4 A prompt Delete S N will appear Enter Yes to delete the existing serial number from the system Note that the other programmed values for that zone will not be deleted This will allow you to re instate a new transmitter in its place 5 A display for the next zone number will appear To exit enter 00 6 Press 99 to exit the programming mode Check Out Procedure for Wireless Zones Transmitter ID When all transmitters have been installed use the Transmitter Sniffer Mode to Sniffer Mode test that they have all been properly programmed 5700 5800 1 Enter Installer Code 3 The keypad will display all zone numbers of RF Systems wireless units programmed into the system 2 Fault each wireless zone causing each device to transmit As the system receives a signal from each of the transmitters the zone number of that transmitter will disappear from the display If a 5700 transmitter is not dipswitched correctly or if a 5800 transmitter is not enrolled its Zone number will not turn off S 3 To exit the Transmitter Sniffer mode enter the Installer Code OFF Continued Go No Go Test Before mounting transmitters permanent
139. or fire zone usage Both batteries will fit inside the panel s cabinet CANADIAN DEPARTMENT OF COMMUNICATIONS DOC STATEMENT NOTICE The Canadian Department of Communications label identifies certified equipment This certification means that the equipment meets certain telecommunications network protective operational and safety requirements The Department does not guarantee the equipment will operate to the user s satisfaction Before installing this equipment users should ensure that it is permissible to be connected to the facilities of the local telecommunications company The equipment must also be installed using an acceptable method of connection In some cases the company s inside wiring associated with a single line individual service may be extended by means of certified connector assembly telephone extension cord The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment Users should ensure for their own protection that the electrical ground connections of the power utility telephone lines and internal metallic water pipe system if present are connected tog
140. or yes 0 for no default 4 Press 29 Fire Sounder Timeout Enter 1 for no timeout O for timeout default 5 Press 30 Alarm Bell Timeout Enter 0 for no timeout 1 for 4 min default 2 for 8 min 3 for 12 min 4 for 16 min 6 Press 51 Confirmation of Arming Ding Enter 0 for no default 1 for yes 2 for yes but with RF arming only 7 Exit the programming mode by entering 99 Testing the Sounder After installation of the sounder is completed the Security System should be carefully tested as follows 1 Connect the battery wires from the control board to the battery observing correct polarity 2 Enter the INSTALLER code 4 1 1 1 and press the TEST key on the wired keypad The external sounder should sound for 1 second if the sounder is good and proper connections have been made Note that if the backup battery is discharged the sounder will not turn on 3 To turn off the test mode enter the INSTALLER code 4 1 1 1 and press the OFF key Section 10 LONG RANGE RADIO General Information Check availability of Model 7720PLUS or 7820 long range radio If output to long range radio is selected all messages that are programmed to go to the primary telephone line receiver will also be sent to the 7720PLUS or 7820 long range radio These messages will be in Contact ID format not affected by entry in field 46 The data line is supervised as well as certain functions in the r
141. or you to make the necessary modifications in order to maintain uninterrupted service If trouble is experienced with this equipment please contact the manufacturer for repair and warranty information If the trouble is causing harm to the telephone network the telephone company may request you remove the equipment from the network until the problem is resolved There are no user serviceable components in this product and all necessary repairs must be made by the manufacturer Other repair methods may invalidate the FCC registration on this product This equipment cannot be used on telephone company provided coin service Connection to Party Line Service is subject to state tariffs This equipment is hearing aid compatible When programming or making test calls to an emergency number briefly explain to the dispatcher the reason for the call Perform such activities in the off peak hours such as early morning or late evening UL NOTICES This is a Grade A residential system The 4285 Phone module and 7720PLUS or 7820 Long Range Radios have not been UL tested and cannot therefore be used in a UL installation The Entry Delay field 438 cannot be greater than 45 seconds for UL installations The maximum number of reports per armed period field 92 must be unlimited set to 1 for UL installations Periodic testing field 49 must be at least every 24 hours set to 1 for UL installations Alarm Sounder plus Auxilia
142. ow appear 3 Scrolls both alphabet and Assume for example that the desired description for zone 1 is BACK actual words in ascending DOOR alphabetical order 1 Scrolls both alphabet and 3 Select the first letter of the desired description note that A is already actual words in descend displayed ing alphabetical order Press key 3 repeatedly to advance through the alphabet e g to B or 6 Selects between alphabet key 1 to go backward Then press 6 to display the first available word and actual word list also beginning with the desired letter e g BABY used to save words Next press 3 repeatedly to move forward or 1 to move backward until 8 Stores the zone descrip the desired word is displayed e g BACK Then press 6 to accept the tion in memory word and toggle back to the alphabet list 13 3 4 For selection of the next word e g DOOR repeat step 3 as follows Press key 8 until the first letter of the next word appears e g D Then press 6 to display the first available word beginning with that letter e g DAUGHTERS Press 3 repeatedly until the desired word e g DOOR appears To accept the word press 6 which toggles back to the alphabet list When all desired words have been entered press 8 to store the description in memory Enter NN where NN is the next zone that you want to review or for which you want to program a descriptor To modify the descriptor enter N
143. r enrolling a transmitter into the system The serial number for the program tool will only remain in the system until the programming mode is exited Entering 97 will not delete the tool Press to continue Note that pressing the key on the keypad will cause the system to back up to the Program Tool prompt 4 Enter the first zone number to be enrolled e g zone 10 Press to continue The system will starting with this zone number search for the first Zone Number Entered transmitter which has all of the following attributes pre programmed in Zone Programming a An input type of RF UR or BR programmed b A loop number programmed c No serial number programmed Enter Zn Num 00 Quit 10 attributes the system will search its database for the first zone that does If the first zone number entered does not have one or more of the above EA and will display it on the next screen 14 1 5 This prompt is displayed when the system has found the next zone 10 Input S N L which needs to be enrolled AXXX XXXX The system will respond to the first serial number transmitted A serial number may be enrolled by one of two methods a Enter the 7 digit serial number printed on the transmitter or b Activate the transmitter by faulting or restoring the input you wish to use for that zone e g press a button open or close a door etc If you do not wish to enroll the zone di
144. rmal Press 75 RF XMTR LOW BATTERY RESTORE CODE This is sent when a transmitter that previously sent in a low battery message has sent a message indicating it no longer has a low battery condition Press 92 NUMBER OF REPORTS IN ARMED PERIOD This option can be used to limit the number of messages alarm amp alarm restore reports sent to the central station in an armed period 0 limits reports to a total of 10 1 allows an unlimited number of reports Press 94 DOWNLOAD PHONE NUMBER Enter up to 12 digits 0 9 11 for 12 for 13 for a pause Do not fill unused spaces End field by entering To clear entries press 94 Press 95 RING DETECTION COUNT FOR DOWNLOADING Refer to the chart below and program this field accordingly Voice Answering Module Machine ET Field 95 Programming Set for value other than 0 1 14 This will enable the control GE to answer the phone call Otherwise it will not be possible to access the module Set for a value higher than the number of rings for which the answering machine is set Example if machine is set for 4 rings use value 5 or higher This is recommended so that the Phone module can still be accessed if the answering machine is turned off and does not answer the phone call Set for value other than 0 1 14 Important Note If 15 is entered in field 95 to bypass an answering machine and a 4285 Phone Module is in
145. rming the system will silence both keypad and external sounders When the system is disarmed any zones that were in an alarm condition during the armed period will be displayed memory of alarm To clear this display simply repeat the disarm sequence enter the security code and press the OFF key again The keypads also feature chime annunciation and 3 panic key pairs or individual panic keys depending on keypad type see Panic Keys on next page for silent audible fire or personal emergency alarms These keys can notify the central station of an alarm condition if that service is connected The following is a brief list of system commands For detailed information concerning system functions refer to the User s Manual Disarmed Not Ready Before arming the system must be in the READY condition all zones must be intact If the NOT READY message appears press the READY key to display faulted zones Arming Away Enter code AWAY 2 Arming Stay 0aaaaaeaaea Enter code STAY 3 Arming Instant 0 00 Enter code INSTANT 7 Arming Maximum 000 Enter code MAXIMUM 4 Quick Arming Simply press key in place of code then press if enabled AWAY STAY INSTANT or MAXIMUM to arm system as desired Note that the key cannot be used in place of code when disarming the system Disarming Enter code
146. ry Power currents must not exceed 600mA total for UL installations Downloading is not permissible for UL installations CALIFORNIA STATE FIRE MARSHAL CSFM 24 HOUR BATTERY BACK UP REQUIREMENTS The California State Fire Marshal has published new regulations which require that all residential fire alarm control panels installed after June 30 1993 must be provided with a back up battery which has sufficient capacity to operate the panel and its attached peripheral devices for 24 hours in the intended standby condition followed by at least 4 minutes in the intended fire alarm signaling condition This control panel can meet these requirements without using a supplementary power supply provided that the panel s auxiliary power and bell output currents are limited as indicated below OUTPUT LIMITATIONS TO MEET CSFM 24 HOUR BATTERY BACK UP REQUIREMENTS FOR UL LISTED RESIDENTIAL FIRE INSTALLATIONS OUTPUT CURRENT LIMITATIONS BATTERY INFORMATION OUTPUT CURRENT MAXIMUM BATTERY CAPACITY RECOMMENDED BATTERY TOTAL AUXILIARY CURRENT TO USE Amp Hrs Yuasa Model No 600mA maximum total NP4 12 ot NP7 12 auxiliary power plus bell output currents NP4 12 two NP7 12 two tNote Use two batteries connected in parallel Obtain an Ademco No 4100EOLR Resistor Kit A dual battery harness is provided with the kit The kit also contains EOL resistors with spade lug heat shrink tubing construction which has been approved by UL and CSFM f
147. ser of the system UL The Phone module is not Listed for UL installation use Mounting The The Phone module may be mounted in the control cabinet if space is available 4285 Phone or if this is not possible on the side of the cabinet or adjacent to it module When mounting the Module outside the cabinet use the screw holes at its rear which will permit it to be mounted horizontally or vertically 2 faced adhesive tape may be used if preferred Wires can be brought out from the side or back a round breakout is also available on the back Affix the Phone module s connections label supplied separately to the inside of the Phone module s cover if the cover is used If you have installed the module within the cabinet affix the label to the inside of the control cabinet s door Phone Module The 4285 is wired between the control panel and the premises handset s It Wiring listens for touch tones on the phone line and reports them to the control panel During on premises phone access it powers the premises phones during off premises phone access it seizes the line from the premises phones and any answering machines Note The phone lines must be in service for the phone module to function even when accessing the system from an on premises phone 1 Make 12V and and data in and data out connections from the Phone module to the control using the connector cable supplied with the Phone module see Figure 12
148. sor e Connects to externally mounted Transmitter inertia type shock detector not supplied Has built in tampered cover switch Has 3 unique input loop codes Loop 1 Terminals for a wired N C sensor loop Loop 2 For a closed circuit contact loop using the built in reed switch in conjunction with a magnet Loop 3 Terminals for a wired closed circuit contact loop Wireless Keypad House ID Can be used to turn the burglary protection on and off Features the same built in panic functions as wired keypads The keypad is identified as zone 00 on wired keypads when it transmits with a low battery 5827BD Wireless Two Way Keypad used with 5800TM Operates the system similarly to wired keypads Can indicate system status via its 3 LEDs and sounder Includes 3 panic keys House ID must be set Requires 5800TM Transmitter Module 5850 Glass Break Detector Requires both sound and shock of GBD breaking glass to cause alarm to be transmitted 5890 PIR Detector Dual element passive infrared detector transmitter with selectable pulse count Note There is a 3 minute lock out between fault transmissions to conserve battery life Package of 4 magnets for use with 5816 and 5817 transmitters Programming the RF Transmitters 5800 RF Systems 1 With at least one 2 line Alpha keypad connected to the keypad terminals power up the system temporarily If you had previously connected the AC transformer to the control pan
149. splayed 4a System is in communication with down keystrokes on keypad loader at central station Wait until down load session is finished 4b System has just been powered and is in its one minute initialization To bypass this time press 0 4c More zones have been programmed than the zone expansion modules can handle Delete some zones or use a higher capability RF receiver 4d Keypads must be set for address 31 non addressable mode 4b di or System Busy displayed 4c E4 or E8 displayed 4d Keypad address setting incorrect SMOKE DETECTOR 1 Detector alarms no apparent Dust dirt in sensing chamber Clean unit s sensing chamber with vacuum reason cleaner per unit s instructions Improper location See unit s instructions for locations to avoid Relocate as necessary Replace detector Check for proper installation of battery Try new battery Replace detector Unit malfunctioning 2 Detector s siren sounds Unit not receiving required power Unit malfunctioning 18 2 CONTACTING TECHNICAL SUPPORT PLEASE Before you call Technical Support be sure you e e READ THE INSTRUCTIONS Check all wiring connections Determine that the power supply and or backup battery are supplying proper voltages Verify your programming information where applicable Note the proper model number of this product and the version level NXXXX number on large circuit module in center
150. splayed press the key on the keypad or the upper right hand button on the program tool a long beep will be heard to verify The following prompt will appear 10 Leam S N 0O No 1 Yes 0 To learn now enter 1 Yes If 0 No is entered the following prompt will appear if a program tool has already been programmed Enter Zn Num 00 Quit 12 Zone Number Entered Enter the next zone number to be enrolled e g zone 12 The system will search for that zone and will display the prompt shown in the beginning of step 5 If you wish to exit the Sequential mode completely enter 00 and press Serial T Loop 7 10 Confirmed A022 4064 The system will enroll the serial number of the first transmitter heard add the loop number entered to this serial number display the serial and loop numbers and cause the keypad to beep twice S If the serial and loop number combination is already present in the system a single long beep will be heard from the keypad If this happens the system will not display the serial number but will wait for a transmission from another transmitter or transmitter loop input 3 6 The system will then enter a confirmation mode so that the operation of the actual programmed input can be confirmed Activate the loop input or button that corresponds to this zone We recommend that you confirm the programming of every transmitter before proceeding to the next zone
151. ss transmitters 5700 or 5800 series e Programming the wireless transmitters 5700 or 5800 series e Checkout procedure for wireless zones test modes UL Wireless may not be used in UL Commercial Burglary installations Wireless Systems Available The VIA 30PSE supports wireless zones which may be used exclusively or in addition to hardwire zones 5 and 6 The system supports two different wireless systems which have many similarities but notable differences in the programming of the transmitters for each system The following receivers may be used with this system and each supports the number of zones shown TABLE 1 5700 Series 5800 Series 4281L 4281CN LT 5881 L 5882L 1 4281M 4281CN Mt 5881M up to 16 4281H 4281CN Ht 5881H 5882H t T 4281 and 5882 type receivers are for use in Canada See special note below S In Canada 5700 systems must use 4281CN series receivers 4281CN L 4281CN M or 4281CN H with Canadian versions of 5700 type transmitters 5800 systems must use 5882 series receivers 5882L or 5882H Information in this manual relative to the 4281 series of receivers applies as well to the 4281CN series Information relative to the 5881 series of receivers applies as well to the 5882 series 5881 and 5882 series receivers can use the same transmitters 5800 type S Any zone number from 10 63 can be used as a 5700 or 5800 series wireless zone do not confuse this with the num
152. stem authorities may not respond appropriately This equipment like other electrical devices is subject to component failure Even though this equipment is designed to last as long as 20 years the electronic components could fail at any time The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance This alarm system should be tested weekly to make sure all sensors and transmitters are working properly The security keypad and remote keypad should be tested as well Wireless transmitters used in some systems are designed to provide long battery life under normal operating conditions Longevity of batteries may be as much as 4 to 7 years depending on the environment usage and the specific wireless device being used External factors such as humidity high or low temperatures as well as large swings in temperature may all reduce the actual battery life in a given installation This wireless system however can identify a true low battery situation thus allowing time to arrange a change of battery to maintain protection for that given point within the system Installing an alarm system may make the owner eligible for a lower insurance rate but an alarm system is not a substitute for insurance Homeowners property owners and renters should continue to act prudently in protecting themselves and continue to insure their lives and property We continue to develop new and improved prot
153. system as follows Displayed as Zone Notes A or 1 amp e Keys A B C are not on all keypads B or amp H e Key D if present is not active eose es ry Important For the Silent Panic functions to be of practical value the system must be connected to a central station Refer to the separate instructions supplied with the Phone module for information concerning its operating procedures Note The Phone module cannot be used to add user codes in this system User codes must be added by using a wired keypad If relay outputs are used two keypad entries available to the user are included among the system operation choices 34 and 35 that may be programmed see the RELAY OUTPUTS section They can manually activate or de activate the relay s for starting or stopping some action such as turning lights on or off etc These keypad entries are Security Code 7 and Security Code 8 Note Whichever entry is used to start stop the action cannot also be used to stop start it The opposite action must either be performed by the other keypad entry or by some other event or operation offered in the programming section e A display of CANCELED ALARM or CA and a zone indication will appear if an exit or interior zone contained a fault during closing at the time the exit delay ended e g exit door left open but the system was disarmed during the entry delay time The alarm sounder and
154. ted into the system until you are ready to enroll the intended transmitter The transmitter that you use as the program tool can also be used as a transmitter in the system If you plan to use an existing transmitter it must first be enrolled into the system as its associated zones You may then program it as the tool A Alpha keypad is required for the following procedures To enroll transmitters sequentially after all other zone information has been programmed do the following 1 Enter Programming mode Installer Code 8 0 on a Alpha keypad Enter the Serial Number Sequential mode by pressing 83 The following prompt will be displayed P m Tool If using a program tool enter 1 If not using a tool enter 0 If a tool rogram ROUE has already been programmed this prompt will not appear If either 0 No 1 Yes 0 not using a tool or one has already been programmed skip to step 4 D 00 Input S N 3 If 1 is entered the system will prompt for the transmitter s serial pu i number Enter the program tool s serial number using one of the AX X X X XXX following methods a Enter the 7 digit serial number printed on the transmitter or b Press any button on the transmitter The keypad should beep twice and display the serial number of the tool 00 InputS N L In this example the serial number is A123 4567 Once enrolled the ER upper left hand button of the program tool can be pressed to ready the A123 4567 3 system fo
155. tem in TEST mode With the Ademco VIA 30PSE 4281L accepts up to 4 transmitters 4281M or 4281H accepts up to 8 transmitters 5881L accepts up to 8 transmitters 5881M 5881H accepts up to 30 transmitters Zones Physical 2 1 4 W x 4 1 8 H x 7 8 D 57mm x 105mm x 22mm Electrical Voltage Input 12VDC Current Drain 20mA Interface Wiring Same as 4127 Physical Electrical 6 1 2 W x 4 1 4 H x 1 1 4 D 169mm x 108mm x 32mm Voltage Input 12VDC Current Drain 35mA Interface Wiring Same as 4127 Physical 6 1 2 W x 4 1 4 H x 1 1 4 D 169mm x 108mm x 32mm Electrical Voltage Input 12VDC Current Drain 35mA Relays off 100mA Relays on Two Output Relays SPDT Contacts Rating 2A max at 28VDC AC Physical Electrical 6 1 2 W x 4 1 4 H x 1 1 4 D 169mm x 108mm x 32mm Voltage Input 12VDC Current Drain 15mA Relays off 180mA Relays on Interface Wiring Same as 4127 Four Output Relays SPDT Contacts Rating 2A max at 28VDC AC 19 2 4285 PHONE MODULE 7720PLUS 7820 a Fond PORN Physical 6 1 2 W x 4 1 4 H x 1 1 4 D 169mm x 108mm x 32mm Electrical Voltage Input 12VDC Current Drain 160mA Device Address Permanently set to address 4 Interface Wiring See 4285 PHONE MODULE section Telephone Line Connections See 4285 PHONE MODULE section Physical 8 1 2 W x 9 1 2 H x 1 3 4 D 216mm x 242mm x 45mm Electrica
156. tended transmitter see step 10 for operation This helps to prevent random signals from being accepted into the system until you are ready to enroll the intended transmitter The transmitter that you use as the program tool can also be used as a transmitter in the system If you plan to use an existing transmitter it must first be enrolled into the system as its associated zones You may then program it as the tool Enrolling Through Zone Programming 56 1 Enter Programming mode Installer Code 8 0 Enter Zone Programming by pressing 56 If the system has been set up to use 5800 series RF and a program tool has been entered skip to step 4 If no program tool has been entered the following prompt will appear Program Tool 2 Ifa program tool is being used enter 1 If not using a tool enter 0 O No 1 Yes 0 and skip to Step 4 3 If 1 is entered the system will prompt for the unit s serial number 00 Input SN L Enter the program tool s serial number using one of the following AX XX XX XX methods a Enter the 7 digit serial number for the transmitter or b Press any button on the transmitter The keypad should beep twice and display the serial number of the tool In this example the serial number is A123 4567 Once enrolled the upper left hand button of the program tool can be pressed to ready the system for enrolling a transmitter into the system Pressing the key on the keypad will cause the system to ba
157. th at least one 2 line Alpha keypad 6139 connected to the keypad terminals on the control power up the system temporarily If you had previously connected the AC transformer to the control panel you need only plug in the transformer to 120VAC outlet to power up the system 2 Enter the programming mode by keying the following on the Alpha keypad Installer code 4 1 1 1 8 0 S If RF zones or wired expansion is used data fields 22 RF SYSTEM TYPE and 25 WIRED EXPANSION RELAY USED must be programmed as required before continuing see Programming Form in the separate Programming Guide 3 Press 56 Note that this is an interactive programming mode It is used to program zone numbers zone types and alarm report codes for all zones that are going to be used Note If you enabled the 5800 wireless system in field 22 entry of 2 the first screen prompt will be Program Tool 0 No 1 Yes Enter 0 No The next prompt will ask you to enter zone number Enter the first zone number that you wish to program or 0 0 to exit zone programming 00 Quit Normally you will be starting with zone 10 this is the default Press to continue Enter Zn Num Zone Number T A summary display will appear showing the present status of that zone s programming Zn zone number ZT zone type RC report code for that zone In input type of zone AW for Aux Wired L Loop not used
158. ther in the Cabinet s s s 2 2 Standard Telephone Line Connections ess 2 3 Keypad Connections to the Control Board ns vesrrenmrnnmennes 3 2 Using a Supplementary Power Supply for Keypads nine vs 3 3 4 Wire Smoke Detector Connections to Zone 5 msn ren 4 1 Wiring Connections 4219 and 4229 Expanders mine venmmnns 5 1 4281 5881 and 5882 Wireless Receivers cover removed 6 3 4204 Connections To Control seen 7 1 4229 Connections to Control sn 7 2 4285 Phone module Wiring Connections sisi sean 8 3 Typical Sounder Wiring sn serres cece 9 2 Long Range Radio Connections ss cee 10 1 Connection of AAV Unit When Not Using a 4285 Phone module 11 2 Connection of AAV Unit When Also Using a 4285 Phone module 12 2 VIA 30PSE Summary of Connections Diagram 008 Inside Back Cover HOW TO USE THIS MANUAL This manual is written to accommodate both the new and the experienced installer of Ademco products A general description of the entire system is located in the first section of this manual This includes the various features available and the optional peripheral devices that the system can support This manual is divided into separate sections A section covering the hardwired zones provides complete information on the capabilities of each basic hardwired zone including its usage programming and a checkout procedure Separate sections are also provided for each peripheral device that can be used in the system and includ
159. tore every sensor individually to assure that it is being monitored by the system Each time a protection zone is faulted the keypad will sound 3 beeps and the identification of each faulted protection zone should appear on the keypad display Note For 5800 wireless systems triggering a zone set to Arm Away Arm Stay or Disarm will take the system out of the TEST mode and cause that action 4 Walk in front of any interior motion detectors if used and listen for the required sound as movement is detected The identification of the detector should appear on the display when it is activated Note Wireless motion detectors Passive Infrared units will send signals out only if they have been inactive for 3 minutes 5 Follow the manufacturer s instructions to test all smoke detectors to ensure that all are functioning properly The identification of each detector should appear on the display when each is activated 6 Turn off the test mode by entering the security code and pressing the OFF key Alarm messages will be sent to the Central Station during the following tests Notify them in advance that tests will be in progress 7 Arm the system STAY and fault one or more perimeter zones After 15 seconds silence alarm sounder s by entering the security code and pressing OFF Arm the system AWAY and check the Entry Exit zones for the programmed exit and entry delays 8 Check the keypad initiated alarms that are in the system
160. uct No increase or alteration written or verbal of the obligations of this Limited Warranty is authorized WVYOVIG SNOILDINNOD 40 AYVINWNS 1Sd0 VIA LT 21NnbI4 GEL LEAD ACID TYPE SET UNIT S DIP SWITCH DO NOT USE GATES BATTERY SO Meter i e ADEMCO No 4219 FOR DEVICE ADDRESS BATTERY NORMALLY NEED NOT BE e g 9 90 12 of WIRED EXE ANSION MODULE See units instructions GE FOR REPLACEMENT g5 8 ADD L EOLR WIRED ZONES YAS USE SAME VALUE SS OR AUX PWR 5 lt BATTERY CAPACITY FOR EMERGENCY 85 ADEMCO No 4229 OUTPUT Be ARED STANDBY USE AT LEAST 4 HOURS We WIRED EXPANSION RELAY MODULE TERMS F ee SE pix 8 ADD LEOLR WIRED ZONES PLUS 2 EOL N 3A Bech OUTPUT RELAYS POWER BATTERY BLACK 5G opp SS VISION CHARGING BATTERY r S8c ge ADEMCO No 4204 RELAY MODULE See ege bb Sch Ze BC e g ADEMCO E E 2e E S z Ce H GAS RELAYS OR COMBUSTION MODULE H No 467 3 ARBOR DETECTOR iodo A77 716B Eer SR E Eeer ds CONNECTOR TABS gt 39 ADEMCO 4281 or 5881 Type DEVICE ADDRESS To Hi SIDE OF SELECTED ZONE FOR TE RF RECEIVER OF 0 ara ee ee BLK_ 22 BLK WIRELESS ZONES See receiver s 4 TO ZONE 5 HEAT EARTH oe RED 16 4281L UPTO4 instructions y DETECTOR ROUND weer S 2 4281M 5881L UP TO 8 7 peee a GROU E en E 5881M UP TO 16 Be TO LO SIDE OF SELECTED ZONE TERMINAL pe ag OT EN D ie Ce 4281 5881H UP TO 30 P IF PROGRAMMED FOR FIRE A USE UL LISTED LIMITED
161. uilt in for Indoor Siren indoor wall mount 747F available for flush mounting 105dB 10 feet 400mA current draw Ademco 747UL Self contained 6 15 volt siren driver built in for Indoor Siren indoor wall mount UL Listed 85dB 10 feet 320mA current draw Ademco 744 6 jumper selected sound outputs Rated at 119dB Siren Driver with use of an 8 ohm 30 watt speaker 1 3 amps current draw Ademco 745X3 12 volt voice siren driver with English Spanish Voice Siren Driver and French voice messages Separate messages for Fire and Burglary Use with 8 ohm speaker UL Listed 1100mA current draw Ademco 705 820 20 watt 8 ohm indoor or outdoor speaker 5 inch Round Speaker Requires a driver Ademco 713 Speaker 40 watt 8 ohm indoor outdoor speaker Requires a driver System Sensor PA400B Indoor piezo sounder red or beige rated at 90 beige PA400R red dB 10 feet Indoor Piezo Sounder Requires special power wiring using additional components UL e Use only UL Listed sounding devices for UL installations e The total current drawn from the alarm output and the auxiliary power output combined cannot exceed 600mA In addition the sounding device must be a UL Listed audible signal appliance rated to operate in a 10 2 13 8 VDC voltage range and must be mounted indoors Example Wheelock Signals Inc siren model 34T 12 provides 85dB A for NFPA 74 amp Standard 985 Non UL The total current drawn
162. using the Paging feature enter the pager number as the secondary phone number Press 43 SUBSCRIBER ACCOUNT No Field 43 is also Central Station Account Number used as the Long Enter 0 9 11 for B 12 for C 13 for D 14 for E 15 for F Range Radio default Bee GES Enter as the fourth digit if a 3 digit account number for 3 1 dialer reporting format is used Enter 0 as the first digit of a 4 digit account number for Nos 0000 0999 End field by pressing and press next field See the blank Programming Form in the separate Programming Guide for examples of Account No entries 15 3 Can only be used if Primary reporting format is Ademco Contact ID If reporting to Pager choose from 6 7 8 or 9 as desired Press x45 PHONE SYSTEM SELECT Enter 1 digit default 0 If Central Station Receiver is not on WATS line 0 Pulse Dial 1 Tone Dial If Central Station Receiver is on WATS line 2 Pulse Dial 3 Tone Dial Press 46 REPORT FORMAT PRIMARY SECONDARY Determines which format is to be used to report to the central station 0 3 1 4 1 ADEMCO Lo Speed Standard this is the default 1 3 1 4 1 Radionics Standard 2 4 2 ADEMCO Lo Speed Standard 3 4 2 Radionics Standard 6 4 2 ADEMCO Express 7 ADEMCO Contact ID Reporting 8 3 1 4 1 ADEMCO Lo Speed Expanded 9 3 1 4 1 Radionics Expanded Enter as the 4th digit of 43 if 3 1 dialer reportin
163. ve its message Once the panel hears the handshake it is programmed to listen for it sends its message The panel then waits for a kissoff frequency from the receiver acknowledging that the message was received and understood If the handshake frequency is not given or is not understood by the panel the panel will not send its message Once the handshake frequency is received and understood by the panel the panel will send its message If there is an error in the transmission the receiver does not receive a valid message the kissoff frequency will not be given by the central station receiver The panel will make a total of eight attempts to the primary telephone number and eight attempts to the secondary telephone number if programmed to get a valid message through If the panel is not successful after its numerous attempts the keypad will display Communication Failure Alpha keypad or FC Fixed word keypad The following chart defines the three sets of handshake kissoff frequencies that the panel supports and the different formats that can be sent for each FORMAT HANDSHAKE TRANSMITS DATA KISSOFF TRANSMIT TIME Low Speed 1400Hz 1900Hz 10PPS 1400Hz Under 15 secs 3 1 Standard report 4 1 4 2 Sescoa Rad 2300Hz 1800Hz 20PPS 2300Hz Under 10 secs 3 1 Standard report 4 1 4 2 Express 1400 2300Hz DTMF 10 cps 1400Hz Under 3 secs 4 2 Contact ID 1400 2300Hz DTMF 10 cps
164. ve programmed 80 mode Refer to the Programming Form worksheet for 81 Mode Upon keying 81 this screen will appear Enter the Zone List Number 01 02 or 03 to program or 00 to end these entries Press the key to advance In the following displays zone list 01 has been selected for programming Enter each zone number to add to the zone list by first entering the zone number then the key example 01 02 03 After all zones desired are entered press 00 to advance To delete the zone list enter 1 Yes All zones in the zone list will be deleted automatically and programming will return to the first screen To save the zone list enter 0 No to advance To delete a zone or zones in a zone list enter 1 Yes to advance Enter each zone to be deleted from the list followed by the key After all zones to be deleted are entered enter 00 to return to the first screen so that another list can be programmed if desired Notes e Any list may include any or all of the system s zone numbers e A zone list can be assigned to more than one output relay e If you only want to review what has been programmed previously enter 8 1 The review can be advanced by using the key When finished enter 0 0 to quit No programmed values can be changed in this mode When programming in 80 and 81 interactive modes is completed exit the programming mode by keying 99 Section 8 4285 PHONE MODULE This se
165. wn in boldface type The Phone module will not provide annunciation of the other words descriptors presently in the system should be re programmed selecting from those words shown in boldface type in the Alpha Vocabulary list The Phone module will not provide annunciation of any other words The ALPHA VOCABULARY LIST and CHARACTER CHART will be found on a following page 4 If a 4285 Phone module is added to an existing VIA 30PSE system the Alpha Assigning Zone Descriptors The Alpha Keypad used with the VIA 30PSE can have a user friendly English language descriptor location of all protection zones keypad panics and RF receiver supervision faults programmed into the system Each descriptor can be composed of a combination of words up to a maximum of 3 selected from a vocabulary of words stored in memory see the list on a following page In addition up to 5 installer defined words can be added to those already in memory Thus when an alarm or trouble occurs in a zone an appropriate descriptor for that zones location will be displayed at the keypad Note Alpha Descriptor entry can be done locally at the Alpha Keypad or re motely using Downloading software The Alpha keypad procedure is described below Entering Zone Descriptors program menu mode 82 The descriptor can be entered when the zone is being defined in field 56 Alternatively zone descriptors can be entered in field 82 There are two methods that can be used to
166. y 50 Testing in this mode assists in determining good mounting locations for the transmitters and verifies that the RF transmission has sufficient signal amplitude margin for the installed system 1 Enter the Installer Code 4 2 Once transmitters are placed in their desired locations and the approximate length of wire to be run to sensors is connected to the transmitter s screw terminals fault each transmitter Do not conduct this test with your hand wrapped around the transmitter as this will cause inaccurate results e The keypad will beep three times to indicate signal reception e If the keypad does not beep re orient or move the transmitter to another location Usually a few inches in either direction is all that is required 3 Mount the transmitter according to the instructions provided with the transmitter 4 Exit the GO NO GO test mode by entering Installer Code OFF You should now proceed to Check Out Procedure for Wireless Zones at the end of this section 5800 Series Transmitter Setup General Information 5800 Series Transmitter Input Loops 5800 series transmitters have built in serial numbers that must be enrolled in the system using the 56 or 83 interactive mode or input to the control via the downloader 5800 series transmitters except 5827 described separately do not have DIP switches Each transmitter s zone number is programmed into the system in 56 mode Some transmitters such

Honeywell Vista-30PSE User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents