Owner/User Manual - Acoustic Research
Contents
1. Acoustic Research PORTABLE WIRELESS SPEAKER WITH 3 5MM JACK MODEL AWS73 INSTALLATION AND OPERATION MANUAL IMPORTANT INFORMATION CAUTION Caution To reduce the risk of electric shock do not remove cover or back No RISK OF ELECTRIC SHOCK user serviceable parts inside Refer servicing to qualified service personnel DO NOT OPEN Important Safety Instructions 8 Protect the power cord from being walked on or pinched 1 Read these instructions particularly at plugs convenience receptacles and the 2 Keep these instructions point where they exit from the apparatus 3 Heed all warnings 9 Unplug this apparatus during lightning storms or when 5 unused for long periods of time 4 Follow all instructions Bi sje 10 Refer all servicing to qualified service personnel 5 Clean only with dry cloth Servicing is required when the apparatus has been 6 Do not block any ventilation openings Install in damaged in any way such as power supply cord or plug accordance with the manufacturer s instructions is damaged liquid has been spilled or objects have fallen 7 Do not install near any heat sources such as radiators into the apparatus the apparatus has been exposed to heat registers stoves or other apparatus including rain or moisture does not operate normally or has been amplifiers that produce heat dropped For PLUGGABLE EQUIPMENT the socket outlet shall The apparatus shall not be exposed to dripping2. the transmitter s three broadcast frequencies 1 2 or 3 switch If you experience poor reception or interference try choosing a different frequency by moving the channel select switch to another position ELJ When the transmitter is receiving an audio signal and is ready x the SIGNAL indicator turns solid green Note If the SIGNAL indicator on the transmitter does not turn on please check the following Confirm the transmitter AC power adapter is securely connected Confirm the cable from the transmitter is securely connected to the audio source output MP3 player A V receiver etc Confirm the audio source is playing audio and is turned up Streaming Audio with the 90OMHz Wireless Transmitter 1 Make sure the 900MHz transmitter is on and that there s something playing on your audio source Turn your audio source up to at least 3 4 full volume 2 If the speaker isn t already on press the On Off button to turn it on 3 The indicator light starts flashing which means the speaker is trying to link with the 900MHz wireless transmitter The indicator light turns solid blue when the speaker is tuned to the 9OOMHz wireless transmitter you should hear sound coming from the speaker now Note If the speaker is not linked to the 9OOMHz transmitter or if the transmitter isn t connected properly the indicator light will continue to blink If this occurs please see the Troubleshooting section of this m
3. this product to the Retailer This Warranty is not transferable and does not cover product purchased serviced or used outside the United States or Canada The warranty does not extend to the elimination of externally generated static or noise to costs incurred for the installation removal or reinstallation of the product The warranty does not apply to any product or part thereof which in the opinion of the company has suffered or been damaged through alteration improper installation mishandling misuse neglect accident or exposure to moisture This warranty does not apply to damage caused by an AC adapter not provided with the product or by leaving non rechargeable batteries in the product while plugged into an AC outlet THE EXTENT OF THE COMPANY S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND IN NO EVENT SHALL THE COMPANY S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT This Warranty is in lieu of all other express warranties or liabilities ANY IMPLIED WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO DURATION OF THIS WARRANTY ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER NCLUDING ANY IMPLIED WARRANTY MUST BE BROUGHT WITHIN A PERIOD OF 24 MONTHS FROM THE DATE OF ORIGINAL PURCHASE IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER No person or representa
4. a classe B est conforme a la norme NMB 003 du Canada Avis d Industrie Canada sur l exposition aux Rayonnements Cet appareil est conforme aux limites d exposition aux rayonnements d Industrie Canada pour un environnement non contr l RF Exposure Warning This equipment must be installed and operated in accordance with provided instructions and the antenna s used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co located or operating in conjunction with any other antenna or transmitter End users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance 12 MONTH LIMITED WARRANTY VOXX Accessories Corporation the Company warrants to the original retail purchaser of this product that should this product or any part thereof under normal use and conditions be proven defective in material or workmanship within 12 months from the date of original purchase such defect s will be repaired or replaced at the Company s option without charge for parts and repair labor To obtain repair or replacement within the terms of this Warranty the product along with any accessories included in the original packaging is to be delivered with proof of warranty coverage e g dated bill of sale specification of defect s transportation prepaid to the Company at the address shown below Do not return
5. anual IMPORTANT The indicator light on the back of the speaker indicates the status of the wireless connection only If you re not using the transmitter or if you re out of range of the transmitter it will keep blinking until it finds the transmitter This is normal 4 Adjust the volume on the speaker as desired Notes If you re using a single speaker with this transmitter keep the L M R switch on the bottom of the speaker in the M position for mono If you re using more than one speaker with this transmitter set the speakers to the L left or R right positions according to their orientation to the listener The speaker automatically retunes if it loses the transmitter s signal You can also press the AutoScan button on the back of the speaker to retune the speaker at any time The transmitter turns off automatically if there is no audio signal present for a prolonged period Interference in the form of static and or distortion can sometimes be heard If this occurs confirm the transmitter speaker adjustments and indicators If the problem persists refer to the Troubleshooting section of this manual USING THE AUXILIARY AUDIO INPUT Making a Direct Connection 1 Connect one end of the provided 3 5mm audio in cable to the AUDIO IN jack on the back of the speaker 2 Connect the other end of the cable to the headphone output on your MP3 player or other portable audio device 3 If
6. is broadcasting 4 x Sigal E E Power P 7 POWER indicator lights when the transmitter is on CHANNEL 1 2 3 lets you find the best transmission frequency for your environment CHANNEL _DGIN 123 OS Ol R AUDIO T _ AUDIO IN R L connects to your sound source lt Back panel using one of the connection options shown here included 12V 200mA AC power adapter DC IN jack receives the small round end of the 7 Included Accessories Speaker AC DC 10V 1500mA adapter fp Transmitter AC DC 12V 3 5mm audio in cable 3 5mm to RCA cable 200mA adapter Note These power units should be plugged in so that they stay vertical or lie flat POWERING THE SPEAKER SYSTEM Powering the Transmitter Connect the small round plug from the transmitter AC anemiar Gack panel power adapter to the transmitter s DC IN jack Plug the iov at other end of the transmitter AC power adapter into any Aepowar Meee standard 120V AC wall outlet Adapter Note Be sure to use the speaker AC power adapter rated 12V DC 200 mA it has the smaller diameter plug Note There is no transmitter ON OFF switch The transmitter is designed to be left plugged in and powered at all times If you will not be using the AWS73 for an extended period of time unplug the transmitter AC power adapter Powering the Speaker There are two options to power your wireless speaker
7. ision reception which can be determined by turning the radio or television off and on the user is encouraged to try to correct interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on another circuit Consult the dealer or an experienced radio TV technician for help Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment Industry Canada Regulatory Information This device complies with RSS 210 of the Industry Canada Rules Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device This class B digital apparatus complies with Canadian ICES 003 IC Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment Avis d Industrie Canada Cet appareil est conforme a la norme CNR 210 des r glements d Industrie Canada Son fonctionnement est sujet aux deux conditions suivantes 1 Cet appareil ne doit pas provoquer d interf rences et 2 Cet appareil doit accepter toutes les interf rences y compris celles pouvant entrainer son dysfonctionnement Cet appareil num rique de l
8. l outlets and the adapter power cords are firmly connected to the power input jacks on the transmitter or speaker or If you re using batteries for the speaker check that they are fresh and inserted with correct polarity Check that the audio source component stereo MP3 player etc is turned on and transmitting sound as it normally should Make sure the volume on your audio source is turned up Check that the speaker volume is turned up If you are using a Tape 2 Monitor output from your receiver amp as the audio output check that you have pressed the Tape Monitor Tape 2 button on the front of the receiver This will turn on the Tape 2 outputs which may not have been active Cause and solution When using battery power make sure the batteries are fresh and replace if necessary Issue Sound is distorted or has static Check that the speaker s indicator light is solid blue not blinking when an audio source is connected to the transmitter Change the position of the channel select switch 1 2 or 3 to change the operating frequency Then press the AutoScan button on the speaker s back panel to make the speaker retune Change the location of the transmitter Place it as high and away from obstructions as possible Avoid placing the transmitter directly on top of or behind a TV Move the transmitter and speaker closer together Sending the signal through certain materials such as gla
9. nnection options and detailed operating instructions for making the AR Wireless Speaker System a valued part of your lifestyle If after having reviewed the instructions you have any questions please call toll free 1 800 732 6866 or visit www acoustic research com Range may vary according to environment TOUR OF THE SPEAKER Speaker Back panel Power indicator blinks when the speaker is first powered on it turns solid blue when the speaker is tuned to the transmitter gt On Off button turns the speaker on and off Auto Scan button rescans for the transmitter s signal Volume buttons adjust the speaker s volume level Audio Input connects directly to your MP3 player smartphone or other portable audio device using the 3 5mm audio in cable provided Volume Bottom Panel L M R switch determines if the speaker plays sound in mono as a stand alone speaker or plays the left or right track in a stereo pair with an additional AWS73 DC IN receives the small round end of the included 10V 1500mA AC power adapter remove the protective cover to insert the adapter Battery Compartment Cover not shown remove to install 6 AA batteries TOUR OF THE SPEAKER 900MHz Wireless Transmitter SIGNAL indicator lights green when the audio is Top panel go FR present and the transmitter
10. or be installed near the equipment and shall be easily splashing or placed near objects filled with liquids accessible Care and Maintenance Always use a soft cloth to clean the speaker and transmitter Never use any product containing alcohol or other solvents as they may damage the surface Use caution when plugging the power transformers in an AC outlet to avoid the risk of electric shock If the speaker are used outside on a deck or patio make sure you take them indoors in the event of a rainstorm to prevent possible damage Do not operate or store the system in extreme temperatures below 32 F 0 C and above 122 F 50 C Product Information Keep your sales receipt to obtain warranty parts and service and for proof of purchase Attach it here and record the serial and model numbers in case you need them These numbers are located on the product Model No Purchase Date Dealer Address Phone INTRODUCTION The Acoustic Research Portable Wireless Speaker with 3 5mm jack lets you enjoy your music anywhere at home or on the go with two ways to connect to your music The 9OOMHz wireless transmitter gives you 150ft of room to roam from your audio source great for outdoor entertaining at home with crystal clear wireless audio The speaker s 3 5mm jack offers a convenient connection option to use anywhere you go just connect your MP3 player or smartphone to the speaker and enjoy This manual covers various co
11. s remove old weak or worn out batteries promptly and recycle or dispose of them in accordance with local and national regulations SETTING UP FOR WIRELESS AUDIO Connecting to an Audio Source Connecting to an A V Receiver a i 1 Plug the stereo plugs on the provided Y adapter tack paneh A V Receiver audio cable into the AUDIO IN jacks on the back of J the transmitter make sure to match the colors on the plugs and jacks Audio Output Mini jack to RCA adapter not included 2 Plug the mini plug end of the provided Y adapter into a mini jack to RCA adapter not included Y adapter l audio cable Va 3 Connect the stereo plugs on the mini jack to RCA adapter to the corresponding left and right audio outputs of your A V receiver amp or other audio source Connecting to a Portable Audio Device 1 Plug the stereo plugs on the provided Y adapter audio N M o ue cable into the AUDIO IN jacks on the back of the transmitter f 2 Plug the mini plug end of the provided Y adapter into E ai 0 the headphone output of your MP3 player or other JE oe portable audio device Transmitter Audio back panel source Adjusting the Transmitter 1 Turn on your audio source for example A V receiver MP3 player stereo etc and play music at a normal listening volume Channel 2 Set the channel select switch on the back of the transmitter to select one of
12. ss tile and metal can decrease the effective transmitting distance of the system SPECIFICATIONS Transmitter Speaker Omni directional 9OOMHz broadcast Push button auto lock tuning Effective transmitting range up to 150 ft 45m 2 way acoustic design Phase locked loop circuitry PLL 2 tweeter 3 woofer S 3 selectable broadcast frequencies 10 Watt rated internal amplifier Omni directional receiver Frequency response 40Hz 15kHz Maximum range results may vary according to Left Mono Right switch environment Operates using supplied AC adapter or six 6 AA batteries not included Stereo audio input FCC Statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B Digital Device pursuant to Part 15 of the FCC Rules These limits are designed to this equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or telev
13. the speaker isn t already on press the On Off button to turn it on Withee Warning This product is designed to work with line level pe outputs or headphone outputs only DO NOT connect it o i pee a directly to speaker outputs as it will permanently damage a the speaker oe D On off 1 1 1 Auto Scan 1 i 1 1 Volume Volume Audio input TURNING THE SPEAKER OFF 1 Press the On Off button on the back of the speaker to turn the speaker off 2 Confirm that the speaker is off by verifying that the indicator light on the speaker s back panel is no longer illuminated TROUBLESHOOTING The following troubleshooting guide takes you through some of the more common problems associated with the installation and or operation of a wireless system If the problem persists please call toll free at 1 800 732 6866 or visit www acoustic research com Issue Cause and solution No sound Check that the transmitter AC power adapter is fully inserted into the wall outlet and the power cord from the AC adapter is firmly connected to the transmitter power input jack Confirm that the speaker is turned on and tuned to the transmitter the indicator light on the back of the speaker should be solid blue not blinking If you re using the power adapters confirm that both for the speaker and for the ransmitter are fully inserted into their wal
14. tive is authorized to assume for the Company any liability other than expressed herein in connection with the sale of this product Some states provinces do not allow limitations on how long an implied warranty lasts or the exclusion or imitation of incidental or consequential damage so the above limitations or exclusions may not apply to you This Warranty gives you specific legal rights and you may also have other rights which vary from state province to state province U S A Audiovox Return Center 150 Marcus Blvd Hauppauge New York 11788 CANADA Audiovox Return Center c o Genco 6685 Kennedy Road Unit 3 Door 16 Mississauga Ontario L5T 3A5 Trademark s Registered www Acoustic Research com MADE IN CHINA AWS73 US IB 03
15. using the included AC power adapter or using 6 AA batteries not included AC Power Adapters T 1 Insert the small round plug from the speaker AC Bottom of power adapter into the DC IN jack on the bottom the speaker s of the speaker AC power 120V AC adapter wall outlet 2 Plug the other end of the speaker AC power adapter into any standard 120V AC wall outlet Note Be sure to use the speaker AC power adapter rated 10V DC 1500 mA Warning This product is water resistant not waterproof Avoid prolonged exposure to wet environments such as rain mist dew etc In other words you can take it out just don t leave it out If you plan to use the speaker in a humid or wet environment we recommend powering it with batteries instead of with the power adapter POWERING THE SPEAKER SYSTEM AA Batteries 1 Remove the battery compartment cover on the bottom of the speaker 2 Insert six 6 AA batteries not included into the speaker following the polarity and as diagrammed inside the battery compartment 3 Replace the battery compartment cover on the bottom of the speaker Note Place the rubber cap in the speaker power input jack when using batteries DO NOT mix batteries with different chemistry types for example a zinc battery with an alkaline battery DO NOT mix new and used batteries DO NOT leave batteries installed in the product when not in use for long periods Alway
Download Pdf Manuals
Related Search