Home
QuickScan I QD2100
Contents
1. 2 Connect Host Interface Keyboard Wedge Interface RS 232 Interface USB Interface gt IBM 46xx Interface Quick Reference Guide 1 Parts of the Imager Parts of the Imager LED Scan Window Trigger Nose Boot Scanning Modes imager can operate in one of several scanning modes Trigger Single When the trigger is pulled scanning is activated until one of the following occurs a programmable duration has elapsed a label has been read the trigger is released This mode is associated with typical handheld reader operation when the trigger is pulled scanning starts and the product scans until the trigger is released or a label is read the maximum programmable duration has elapsed Trigger Hold Multiple When the trigger is pulled scanning starts and the product scans until the trigger is released or a program mable duration has elapsed Readi ing a label does not disable scanning Double Read Timeout prevents undesired multiple reads while in this mode Trigger Pulse Multiple When the trigger is pulled and released scanning is activated until programmable duration has elapsed or the trigger has been pulled again to transition to another state Double Read Timeout prevents undesired multiple reads while in this mode Flashing The reader flashes on and off regardless of the trigger status
2. Interface or power cables are loose Ensure all cable connec tions are secure LED comes on but bar code does not decode Imager not pro grammed for correct barcode type Ensure imager is pro grammed to read the type of barcode scanned Refer to the Product Reference Guide PRG for more information Barcode label is unreadable Check the label to ensure it is not defaced Try scan ning another barcode type Distance between imager and barcode is incorrect Move imager closer to or further from the barcode Barcode reading ability has degraded Scan Window has become scratched or contaminated with dust Replace window as instructed in this guide Barcode is decoded but Imager not pro Scan the appropriate host type barcode Refer to the not transmitted to the grammed for the cor Product Reference Guide host rect host type PRG for more informa tion For detailed troubleshooting refer to the Product Reference Guide NOTE 6 QuickScan i LED and Beeper Indications LED and Beeper Indications imager s beeper sounds and its LED illuminates to indicate various acies or errors on the reader A Green Spot also lights to indicate a good read The tables below list these indi cations One exception to the behaviors listed in the tables is that the reader s functions are programmable and may or may not be turned on For example ce
3. 1 See the Product Reference Guide PRG for additional programmable features in this case Scanning Active Time 2 Double Read Timeout is also programmed using the PRG 3 Controlled by Flash On Time and Flash Off Time Use the PRG to pro gram these options Quick Reference Guide 3 Always On No trigger pull is required to read a barcode Scanning is continually on If the trigger is pulled the reader acts as if it is in Trigger Single Mode Double Read Timeout prevents undesired multiple reads while in this mode Stand Mode No trigger pull is required to read a bar code Scan ning is turned on automatically when an item is placed in read er s field of view If the trigger is pulled the eis acts as if it in Trigger Single mode Double Read Timeout prevents un desired multiple reads while in this mode Trigger Object Sense This mode is similar to Stand Mode ex cept that a trigger pull is required to activate the decoder Scan Mode Trigger Single 1 Double Read Timeout is programmed using the PRG 2 Double Read Timeout is programmed using the PRG QuickScan Scanning Modes Scanning Modes continued Scan Mode Flash ing Quick Reference Guide 5 Troubleshooting Problem Possible Cause Possible Solutions Nothing happens when No power to the Check system power scan button is Ensure power supply is pulled ger connected
4. b any other trade secrets marked appropriately or identified as propri etary or confidential and c any information that End User under the circumstances should recognize as confidential Proprietary Informa tion does not include any information that the receiving party can establish was 1 in the public domain 2 already in the receiving party s possession or rightfully known prior to receipt 3 rightfully learned from a third party not in violation of any other s proprietary rights or 4 independently developed without access to Proprietary Information 1 4 Datalogic Product means the Datalogic Quickscan series scanner product including all embedded Software in and all Documentation related to such product which has been purchased or otherwise acquired by End User whether obtained directly or indirectly from Data logic 1 5 Software means any software or computer programs of Datalogic or its third party licensors in machine readable form which is embedded in the Datalogic Product whether obtained directly or indirectly from Dat alogic including any replacement update upgrade enhancement or modification 2 Scope Of License Granted 2 1 Datalogic grants to End User a non exclusive non transferable perpetual license to use the Software solely on the Datalogic Product in which it is embedded designated Datalogic Product in machine readable form only solely for End User s internal business purposes This
5. be bound to the terms of this Agreement Datalogic is not willing to license the Software to you you may not use the Datalogic Product or the Software and you must contact the party from whom you acquired the Data logic Product for instructions This End User Software License Agreement Agreement is a legally binding agreement governing the licensing of the Software and Documentation by Dat alogic Scanning Inc and its Affiliates Datalogic to the entity or person who has purchased or otherwise acquired a Datalogic Product End User For purposes of this Agreement any software that is associated with a separate end user license agreement is licensed to you under the terms of that license agreement Datalogic and End User hereby agree as follows 1 Definitions 1 1 Affiliate means a business entity currently existing or later acquired that controls is controlled by or is under common control with Datalogic S p A 1 2 Documentation means materials such as user s guides program refer ence guides quick reference guides manuals or similar materials associated with or related to the Datalogic Product whether in printed online or other form 1 3 Proprietary Information means a source code object code software documentation and any related internal design system design data base design algorithms technology technical data or information implementation techniques and trade secrets related to the Software
6. contemporaneous agreements written or oral between the parties concerning the licensing of the Software This Agreement may not be changed amended or modified except by writ ten document signed by Datalogic 11 2 Notice All notices required or authorized under this Agreement shall be given in writing and shall be effective when received with evidence of receipt Notices to Datalogic shall be sent to the attention of Contract Administration Datalogic Scanning Inc 959 Terry Street Eugene OR 97402 or such other address as may be specified by Datalogic in writ ing 11 3 Waiver A party s failure to enforce any of the terms and conditions of this Agreement shall not prevent the party s later enforcement of such terms and conditions 11 4 Governing Law Venue This Agreement and the rights of the parties hereunder shall be governed by and construed in accordance with the laws of the State of Oregon U S A without regard to the rules govern ing conflicts of law The state or federal courts of the State of Oregon located in either Multnomah or Lane counties shall have exclusive juris diction over all matters regarding this Agreement except that Datalogic shall have the right at its absolute discretion to initiate proceedings in the courts of any other state country or territory in which End User resides or in which any of End User s assets are located 11 5 Attorneys Fees In the event an action is brought to enforce the terms a
7. datalogic com Singapore Datalogic Scanning Singapore PTE LTD Telephone 65 6435 1311 singapore scanning datalogic com Iberia Datalogic Scanning SAS Sucursal en Espaha Telephone 34 91 746 28 60 spain scanning datalogic com United Kingdom Datalogic Scanning LTD Telephone 44 0 1582 464900 uk scanning datalogic com gt DATALOGIC www scanning datalogic com Datalogic Scanning Inc 959 Terry Street Eugene OR 97402 USA Telephone 541 683 5700 Fax 541 345 7140 2008 2012 Datalogic Scanning Inc 820045914 Rev E April 2012
8. of corrections or ii QuickScan i responding to End User s problem reports according to Datalogic s standard assistance practices Datalogic does not warrant that the product will meet End User s requirements or that use of the product will be uninterrupted or error free or that Datalogic s remedial efforts will correct any nonconformance This limited warranty does not cover any product that have been subjected to damage or abuse whether intentionally accidentally or by neglect or to unauthorized repair or unauthorized installation and shall be void if End User modifies the product uses the product in any manner other than as established in the Documentation or if End User breaches any of the provisions of this Agreement 6 2 EXCEPT AS PROVIDED IN THIS AGREEMENT THE DATALOGIC PRODUCT IS PROVIDED AS IS AND DATALOGIC MAKES NO WARRANTIES OF ANY KIND EXPRESS OR IMPLIED WRITTEN OR ORAL WITH RESPECT TO THE PRODUCT AND SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 7 Infringement Tal Datalogic will defend End User against any claim in a lawsuit that the Datalogic Product furnished hereunder infringe a United States patent or copyright of a third party and Datalogic will pay any damages finally awarded against End User by a court of competent jurisdiction that are attributable to such claim or will pay End User s part of any settlement that is attributable to such claim
9. provided that 1 End User notifies Datalogic promptly in writing of the claim 2 Datalogic controls the defense or settlement of the claim and 3 End User cooperates fully with Datalogic in such defense or settlement All notices of a claim should be sent to Datalogic Scanning Inc Legal Department 959 Terry Street Eugene OR 97402 7 2 In the defense or settlement of any such claim Datalogic may at its option 1 procure for End User the right to continue using the Datalogic Product 2 modify the Datalogic Product so that it becomes non infringing 3 replace the Datalogic Product with an equivalent product not subject to such claim or 4 provide End User an opportu nity to return the Datalogic Product and receive a refund of the pur chase price paid less a reasonable allowance for use 7 3 Datalogic shall have no liability to End User for claims of infringement based upon 1 the use of any Datalogic Product in combination with any product which Datalogic has not either furnished or authorized for use with such Datalogic Product 2 the use of any Datalogic Product designed manufactured or modified to the specifications of End User or 3 End User s modification of the Datalogic Product without written authorization from Datalogic 7 4 THE FOREGOING STATES DATALOGIC S COMPLETE AND ENTIRE OBLIGATION CONCERNING CLAIMS OF PATENT COPYRIGHT OR OTHER INTELLECTUAL PROPERTY INFRINGEMENT CANCELS AND SUPERCEDES ANY PRIOR AGREEMENTS WHET
10. this manual that is complete and accurate however Datalogic reserves the right to change any specification at any time without prior notice Datalogic and the Datalogic logo are registered trademarks of Datalogic S p A in many countries including the U S A and the E U All other brand and product names may be trademarks of their respec tive owners This product may be covered by one or more of the following patents 4603262 4639606 4652750 4672215 4699447 4709369 4749879 4786798 4792666 4794240 4798943 4799164 4820911 4845349 4861972 4861973 4866257 4868836 4879456 4939355 4939356 4943127 4963719 4971176 4971177 4991692 5001406 5015831 5019697 5019698 5086879 5115120 5144118 5146463 5179270 5198649 5200597 5202784 5208449 5210397 e 5212371 5212372 5214270 5229590 5231293 5232185 5233169 5235168 5237161 5237162 5239165 5247161 5256864 5258604 5258699 5260554 5274219 5296689 5298728 5311000 5327451 5329103 5330370 5347113 5347121 5371361 5382783 5386105 5389917 5410108 5420410 5422472 5426507 5438187 5440110 5440111 5446271 5446749 5448050 5463211 5475206 5475207 5479011 5481098 5491328 5493108 5504350 5508505 5512740 5541397 5
11. 2001 A2 2003 60950 1 2007 EN 61000 3 2 2006 EN 61000 3 3 1995 A1 2001 A2 2005 EN 61000 4 3 2002 Generic Emissions Generic Emissions Generic Emissions Generic Immunity ITE Includes ENG1000 4 2 ESD 4 4 EFT 4 5 Surge 4 6 Cond Immunity and 4 11 Voltage dips interruptions ITE Safety Harmonic Current Voltage Fluctuation Flicker Radiated RF Immunity Susceptibility Equipment Type Handheld Barcode Scanning Equipment Interface Protocol RS 232 USB Keyboard Wedge IBM Placed into EU Service November 2008 under the Datalogic logo Responsible Manufacturer Datalogic Scanning Inc 959 Terry St Eugene Oregon USA od Mat Brad West October 24 2008 Vice President Supply Chain Operations Datalogic Scanning Inc CE Australia Datalogic Scanning Pty Ltd 61 2 9870 3200 australia scanning datalogic com France and Benelux Datalogic Scanning SAS Telephone 33 01 64 86 71 00 france scanning datalogic com Germany Datalogic Scanning GmbH Telephone 49 0 61 51 93 58 0 germany scanning datalogic com India Datalogic Scanning India Telephone 91 22 64504739 india scanning datalogic com Italy Datalogic Scanning SpA Telephone 39 0 39 62903 1 italy scanning datalogic com Japan Datalogic Scanning KK Telephone 81 0 3 3491 6761 japan scanning datalogic com Latin America Datalogic Scanning Inc Telephone 305 742 2206 latinamerica scanning
12. 552593 5557095 5563402 5565668 5576531 5581707 5594231 5594441 5598070 5602376 5608201 5608399 5612529 5629510 5635699 5641958 5646391 5661435 5664231 5666045 5671374 5675138 5682028 5686716 5696370 5703347 5705802 5714750 5717194 5723852 5750976 5767502 5770847 5786581 5786585 5787103 5789732 5796222 5804809 5814803 5814804 5821721 5822343 5825009 5834708 5834750 5837983 5837988 5852286 5864129 5869827 5874722 5883370 5905249 5907147 5923023 5925868 5929421 5945670 5959284 5962838 5979769 6000619 6006991 6012639 6016135 6024284 6041374 6042012 6045044 6047889 6047894 6056198 6065676 6069696 6073849 6073851 6094288 6112993 6129279 6129282 6134039 6142376 6152368 6152372 6155488 6166375 6169614 6173894 6176429 6188500 6189784 6213397 6223986 6230975 6230976 6244510 6259545 6260763 6266175 6273336 6276605 6279829 6290134 6290135 6293467 6303927 6311895 6318634 6328216 6332576 6332577 6343741 6454168 6478224 6568598 6578765 6705527 6857567 6974084 6991169 7051940 7170414 7172123 7201322 7204422 7215493 7224540 7234641 7243850 7374092 7407096 7490770 74
13. 95564 7506816 7527198 7527207 7537166 7562817 601 26 118 6 AU703547 0312631 0313590 0320011 0320012 0323492 0330707 0330708 0349109 0350127 0350735 D351149 0351150 0352936 0352937 D352938 0352939 0358588 D361565 0372234 0374630 0374869 0375493 0376357 0377345 0377346 0377347 0377348 0388075 0446524 0606544 EP0256296 EP0260155 EP0260156 EP0295936 EP0325469 EP0349770 EP0368254 EP0442215 EP0498366 EP0531645 EP0663643 EP0698251 EP01330772 EP870761 GB2252333 GB2284086 GB2301691 GB2304954 GB2307093 GB2308267 GB2308678 GB2319103 GB2333163 GB2343079 GB2344486 GB2345568 GB2354340 ISR107546 ISR118507 159118508 JP1962823 JP1971216 JP2513442 JP2732459 2829331 JP2953593 JP2964278 MEX185552 187245 RE37166 RE40071 Other Patents Pend ing Datalogic Scanning Inc QUICKSCAN PRODUCT SERIES END USER LICENSE AGREEMENT Notice to End User The Datalogic Product you have acquired contains embedded Software which is integral to the product s operation This Soft ware is being provided to you under license subject to the terms and condi tions of this Agreement If you use the Datalogic Product you will be deemed to have accepted the terms and conditions of this Agreement If you do not intend to
14. Agree ment does not convey ownership of the Software to End User Title to the Software shall be and remain with Datalogic or the third party from whom Datalogic has obtained a licensed right As used in this Agree ment the term purchase or its equivalents when applied to the Soft ware shall mean acquire under license End User is not entitled to Quick Reference Guide i receipt or use of the source code to any Software 2 2 End User shall not copy modify decompile disassemble reverse engi neer or otherwise reproduce or remanufacture the Software whether modified or unmodified nor sell assign sublicense distribute lend rent give or otherwise transfer the Software to any other person or organization for purposes other than as expressly provided in this Agreement without Datalogic s prior written consent 3 Transfers Support 3 1 Any copying installing reproduction remanufacture reverse engineer ing electronic transfer or other use of the Software on other than the designated Datalogic Product will be a material breach of this Agree ment However Datalogic may elect not to terminate this Agreement or the granted licenses but instead may elect to notify End User that End User is deemed to have ordered and accepted a license for each breaching use End User shall pay Datalogic the applicable list price for such licenses as of the date of such breach 3 2 End User shall not sell assign sublicense distribu
15. DATALOGIC QuickScan i QD2100 General Purpose Corded Handheld Linear Imager Bar Code Reader Quick Reference Guide Datalogic Scanning Inc 959 Terry Street Eugene Oregon 97402 USA Telephone 541 683 5700 541 345 7140 An Unpublished Work All rights reserved No part of the contents of this documentation or the proce dures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic Scanning Inc or its subsidiaries or affiliates Datalogic or Datalogic Scanning Owners of Datalogic products are hereby granted a non exclusive revocable license to reproduce and transmit this documentation for the purchaser s own internal business purposes Pur chaser shall not remove or alter any proprietary notices including copyright notices contained in this documentation and shall ensure that all notices appear on any reproductions of the documentation Should future revisions of this manual be published you can acquire printed versions by contacting your Datalogic representative Electronic versions may either be downloadable from the Datalogic web site www scanning datalogic com or provided on appropriate media If you visit our website and would like to make comments or suggestions about this or other Datalogic publications please let us know via the Contact Datalogic page Disclaimer Datalogic has taken reasonable measures to provide information in
16. HER ORAL OR WRITTEN BETWEEN THE PARTIES CONCERNING SUCH CLAIMS AND WILL NOT BE MODIFIED OR AMENDED BY ANY PAST CONTEMPORANEOUS OR FUTURE AGREEMENTS OR DEALINGS BETWEEN THE PARTIES WHETHER ORAL OR WRIT TEN EXCEPT AS SET FORTH IN A FUTURE WRITING SIGNED BY BOTH PARTIES 8 Limitation Of Liability EXCEPT AS PROVIDED IN SECTION 7 DATALOGIC SHALL NOT BE LIABLE FOR ANY CLAIMS AGAINST END USER BY ANY OTHER PARTY IN NO EVENT SHALL DATALOGIC S LIABILITY FOR DAMAGES IF ANY WHETHER BASED UPON CONTRACT TORT INCLUDING NEGLIGENCE PRODUCT LIABILITY STRICT LIABILITY WARRANTY OR ANY OTHER BASIS EXCEED THE PRICE OR FEE PAID BY END USER FOR THE DATALOGIC PRODUCT UNDER NO CIRCUMSTANCES SHALL DATALOGIC BE LIABLE TO END USER OR ANY THIRD PARTY FOR LOST PROFITS LOST DATA INTERRUPTION OF BUSINESS OR SERVICE OR FOR ANY OTHER SPE CIAL CONSEQUENTIAL CONTINGENT INDIRECT INCIDENTAL PUNI TIVE EXEMPLARY OR OTHER SIMILAR DAMAGES EVEN IF DATALOGIC Quick Reference Guide iii aaa HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES 9 Government Restricted Rights International Use 9 1 Use duplication or disclosure of the Software by the U S Government is subject to the restrictions for computer software developed at private expense as set forth in the U S Federal Acquisition Regulations at FAR 52 227 14 g or 52 227 19 or in the Rights in Technical Data and Com puter Software clause at DFARS 252 227 7013 c 1 ii which
17. ce Requirements Canada This Class B digital apparatus complies with Canadian IC ES 003 Cet appareil num rique de la classe B est conforme la norme 003 du Camada 14 QuickScan i Replacing the Scan Window Replacing the Scan Window Ifthe Scan Window becomes scratched broken contaminat ed with heavy dust fix it by removing the Nose Boot and clean ing or installing a new window Datalogic offers a replacement window as an orderable accessory Nose Boot Scan Window To replace the Scan Window first remove power from the im ager then hold the imager with the Scan Window facing up Gently pull off the Nose Boot and tilt the imager to one side to remove the window Proceed to the next step immedi ately DO NOT leave the interior of the imager exposed CAUTION Holding it by its edges carefully place the clean replacement Scan Window in position and secure it in place by reinstalling the Nose Boot Quick Reference Guide15 Imager Labeling Labels are shown here to illustrate their location only Please view the labels on your product for actual details G Regulatory 8 Serial Number FOR LASER VERSION COMPLIES WITH 21 CFR 1040 10 AND 1040 11 EXCEPT FOR DEVIATIONS PURSUANT TO LASER NOTICE NO 50 DATED JUNE 24 2007 IEC EN60825 1 2007 SEE QRG FOR PATENT INFO 6 Fe 9 6 5 Waste Electrical and Electronic Equipment WEEE Statement English F
18. cretion can re turn the units in the factory default configuration or with any software or firmware update available at the time of the repair other than the firmware or software installed during the manufacture of the product Customer accepts responsibility to maintain a back up copy of its software and data 16 QuickScan i Imager Labeling Warranty Claims Process In order to obtain service under the Factory Warranty Customer must notify Datalogic of the claimed defect before the expiration of the applicable Warranty period and obtain from Datalogic a return authorization number RMA for return of the product to a designated Datalogic service cen ter If Datalogic determines Customer s claim is valid Datalogic will repair or replace product without additional charge for parts and labor Customer shall be responsible for packaging and shipping the product to the designed Datalogic service center with shipping charges prepaid Datalogic shall pay for the return of the product to Customer if the shipment is to location within the country in which the Datalogic service center is located Customer shall be responsible for paying all shipping charges duties taxes and any other charges for products returned to any other locations Failure to follow the applicable RMA policy may result in a processing fee Customer shall be responsible for return shipment expenses for products which Datalogic at its sole discretion determines are
19. eights Reduce or eliminate vibration Reduce or eliminate direct pressure Provide adjustable workstations Provide adequate clearance Provide a suitable working environment Improve work procedures Regulatory Information models are designed to be compliant with rules and regula tions in locations they are sold and will be labeled as required Any changes or modifications to equipment not expressly ap proved by Datalogic could void the user s authority to operate the equipment Power Supply Use only a power supply approved by Datalogic for this prod uct and model Mode s require either a Lined class II or class III with a Limited Power Source LPS which supplies power di rectly to the imager For the safety certification to be valid class input power sources must be IEC EN60950 1 EN 60335 series EN 60065 or relevant approved Input 100 240 VACOutput 5 2 VDC Max Current 0 4 AmpsPower 15 Watts For USB Power Off Terminal appli cations attach to USB 1 0 1 1 or 2 0 host device only NOTE Quick Reference Guide13 SS Hinweis Benutzen Sie nur eine von Datalogic genehmigte Stromversor gung Die Modelle erfordern eine Stromquelle der Klasse II oder III mit einer Leistungsbegrenzung LPS F r eine g ltige Sicherheitszertifizierung m ssen Klasse III Stromquellen am Eingang nach den Bestimmungen IEC EN60950 1 EN 60335 Serien EN 60065 oder entsprechenden zugelassen sein Einga
20. ers 1 Download the correct USB Com driver from www datalogic com 10 QuickScan Programming Barcodes Keyboard Wedge Interface use a Keyboard Wedge interface scan the barcode for the desired keyboard type Select K AT PS 2 25 286 30 286 60 70 80 90 amp 95 w Standard Key Encoding Select K IBM AT PS2 with standard key is without external kbd Select K AT PS 2 25 286 30 286 pa 5 i 70 80 90 amp 95 w Alternate Key Select KBD AT ALT NK for IBM AT PS2 with alternate key puis but without external keyboard Quick Reference Guide 11 Keyboard Wedge Interface continued Select KBD XT PC XT w Standard Key Encoding Select KBD IBM 3153 for IBM Terminal 3 Select K for IBM Terminals 31xx 32xx ps make only keyboard Seleci K for IBM Terminals 31xx 32xx s pn make break keyboard Select K for DIGITAL D VT4xx 12 QuickScan Ergonomic Recommendations Ergonomic Recommendations In order to avoid or minimize the potential risk of ergonomic injury fol low the recommendations below Consult with your local Health amp CAUTION Safety Manager to ensure that you are adhering to your company s safety programs to prevent employee injury Reduce or eliminate repetitive motion Maintain a natural position Reduce or eliminate excessive force Keep objects that are used frequently within easy reach Perform tasks at correct h
21. etc No Assignment Customer may not assign or otherwise transfer its rights or obligations under this warranty except to purchaser or transferee of product No attempted assignment transfer in violation of this provi sion shall be valid or binding upon Datalogic DATALOGIC S LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EX PRESS OR IMPLIED ORAL OR WRITTEN STATUTORY OR OTHERWISE INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY FIT NESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT DATALOGIC SHALL NOT BE LIABLE FOR ANY DAMAGES SUSTAINED BY CUSTOMER ARISING FROM DE LAYS IN THE REPLACEMENT OR REPAIR OF PRODUCTS UNDER THE ABOVE THE REMEDY SET FORTH IN THIS WARRANTY STATEMENT IS THE CUSTOMER S SOLE AND EXCLUSIVE REMEDY FOR WARRANTY CLAIMS UNDER NO CIRCUMSTANCES WILL DATALOGIC BE LIABLE TO CUSTOMER OR ANY THIRD PARTY FOR ANY LOST PROFITS OR ANY INCIDENTAL CONSEQUENTIAL IN DIRECT SPECIAL OR CON TINGENT DAMAGES REGARDLESS OF WHETHER DATALOGIC HAD ADVANCE NO TICE OF THE POSSIBILITY OF SUCH DAMAGES Risk of Loss Customer shall bear risk of loss or damage for product in transit to Datalogic Datalogic shall assume risk of loss or damage for product in Datalogic s possession In the absence of specific written instruc tions for the return of peda to Customer Datalogic will select the carrier but Datalogic shall not thereby assume any liability in connection with the return shipment Quick Reference G
22. ever is applicable 9 2 If End User is using the Datalogic Product outside of the United States End User must comply with the applicable local laws of the country in which the Datalogic Product is used with U S export control laws and with the English language version of this Agreement The provisions of the United Nations Convention on International Sale of Goods shall not apply to this Agreement 10 Termination 10 1 Either party may terminate this Agreement or any license granted under this Agreement at any time upon written notice if the other party breaches any provision of this Agreement 10 2 Upon termination of this Agreement End User immediately shall cease using any nonembedded software and shall return to Datalogic or destroy all non embedded software covered by this Agreement and shall furnish Datalogic with a certificate of compliance with this provi Sion signed by an officer or authorized representative of End User For embedded software End User agrees to sign a waiver prepared by Datalogic concerning further use of the embedded Software End User s resumed or continued use of the embedded Software after ter mination shall constitute End User s agreement to be bound by the terms and conditions of this Agreement for such use 11 General Provisions 11 1 Entire Agreement Amendment This document contains the entire agreement between the parties relating to the licensing of the Software and supersedes all prior or
23. nd conditions of this Agreement the prevailing party shall be entitled to reasonable attorneys fees both at trial and on appeal END iv QuickScan i Software Product Policy Software Product Policy Datalogic reserves the right to ship its products with the latest version of software firm ware available This provides our customers with the very latest in Datalogic software technology The only exception to this policy is when the buyer has a signed contract with Datalogic that clearly defines the terms and conditions for making software firmware changes in products shipped to the buyer Customers Under Software Support Customers that elect to subscribe to Datalogic Software Maintenance and Support Agreement will receive 30 days advance notification of 1 the release of a new software version and or 2 discontinuation of any prior software version that will no longer be supported Datalogic will provide maintenance for a fee that will assist customers in transitioning to the next software version If a customer is currently using the software version being discontinued the customer may elect to transition to any one of the newer versions depending on the hardware in use arrange for a Software Maintenance and Support Agreement please contact your Datalogic sales person Quick Reference Guide 5 vi QuickScan i Connect Disconnect 0 Connect Disconnect Cable
24. ng 100 240 VACAusgang 5 2 VDC Max Strom 0 4 AmpsMax Leistung 15 W Radio Frequency Interference Requirements This equipment has been tested and found to FE mm comply with the limits for a Class B digital de vice pursuant to Part 15 of the FCC rules These limits are designed to provide reason able protection against harmful interference in a residential in stallation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accor dance with the instruction manual may cause harmful interfer ence to radio communications However there is no guarantee that interference will not occur in a particular installation If the equipment does cause harmful interference to radio or televi sion reception which can be determined by turning the equip ment and on the user is encouraged to try to correct the interference by one or more of the following measures 9 Re orient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the CAUTION user s authority to operate the equipment FOR HOME OR OFFICE USE Radio Frequency Interferen
25. not defective or eligible for warranty repair Warranty Exclusions The Datalogic Factory Warranty shall not apply to i any product which has been damaged modified altered repaired or upgraded by other than Datalogic service personnel or its authorized representatives Gi any claimed defect failure or damage which Datalogic determines was caused by faulty operations improper use abuse misuse wear and tear negligence improper storage or use of parts or accessories not approved or supplied by Datalogic ii any claimed defect or damage caused by the use of product with any other instrument equipment or apparatus Gv any claimed defect or damage caused by the failure to provide proper maintenance includ ing but not limited to cleaning the upper window in accordance with product manual any defect or damage caused by natural man made disaster such as but not limited to fire water damage floods other natural disasters vandalism or abusive events that would cause internal and external component damage or destruction of the whole unit consumable items vi any damage or malfunctioning caused by non restoring action as for example firmware software upgrades software or hardware reconfigurations etc vii the replacement of upper window cartridge due to scratching stains or other degradation and or viii any consumable or equivalent e g cables power supply batteries keypads touch screen triggers
26. ns are in your imag er or you ve changed some options and want the factory set tings restored scan the Factory Default Settings barcode below This will copy the factory configuration for the currently active interface to the current configuration Factory Default Settings Host Interfaces Cables may vary depending upon sys tem configuration Some interfaces require the imager to NOTE start in the disabled state when pow ered on If additional imager configura tion is desired while in this state pull the trigger and hold it for five seconds The imager will change to a state that allows programming with barcodes 8 QuickScan i Programming Barcodes RS 232 Interface To use an RS 232 interface scan the barcode for the desired 5 232 host type Select RS 232 Standard Select RS 232 Wincor Nixdorf Select RS 232 OPOS for use with OPOS UPOS JavaPOS IBM Interface Select IBM Port 5B Select IBM Port 9B Quick Reference Guide 9 USB Interface The imager attaches directly to USB host or powered USB hub auis powered by it No additional power supply is re quired When using a USB interface the imager auto detects the USB and defaults to the HID keyboard interface Select USB COM STD simulates RS 232 standard interface Select USB Keyboard with standard key encoding Select USB Alternate Keyboard with alternate key encoding Select USB OEM Select USB KBD APPLE for Apple comput
27. o right or interest in any Propri etary Information 5 2 End User shall not disclose provide or otherwise make available the Proprietary Information of Datalogic or its third party licensors to any person other than End User s authorized employees or agents who are under confidentiality agreement and End User shall not use the Propri etary Information other than in conjunction with use of the Datalogic Product exclusively for End User s internal business purposes End User shall take steps to protect the Proprietary Information no less securely than if it were End User s own intellectual property 5 3 The provisions of this Proprietary Information Section shall survive and continue for five 5 years after the termination of this Agreement 6 Limited Warranty 6 1 Datalogic warrants that under normal use and operation the Datalogic Product will conform substantially to the applicable Documentation for the period specified in the Documentation During this period for all reproducible nonconformities for which Datalogic has been given writ ten notice Datalogic will use commercially reasonable efforts to rem edy nonconformities verified by Datalogic End User agrees to supply Datalogic with all reasonably requested information and assistance necessary to help Datalogic in remedying such nonconformities For all defects reported to Datalogic within the warranty period Datalogic s lia bility is limited to providing End User with one copy
28. or information about the disposal of Waste Electrical and Electronic Equipment WEEE please refer to the website at www scanning datalogic com Italian Per informazioni sullo smaltimento delle apparecchiature elettriche ed elettroniche consultare il sito Web www scanning datalogic com French Pour toute information relative l limination des d chets lectroniques WEEE veuillez consulter le site internet www scanning datalogic com German Informationen zur Entsorgung von Elektro und Elektronik Altger ten WEEE erhalten Sie auf der Webseite www scanning datalogic com Spanish Sidesea informaci n acerca de los procedimientos para el desecho de los residuos del equipo el ctrico y electr nico WEEE visite la p gina Web www scanning datalogic com Portuguese Para informa es sobre a disposi o de Sucatagem de Equipamentos El tricos e Eletr nicos WEEE Waste Electrical and Electronic Equipment consultar o site web www scanning datalogic com Chinese 5 WEEENES 184845 Datalogic 34 www scanning 081810816 come Datalogic Scanning Limited Factory Warranty Warranty Coverage Datalogic Scanning Datalogic hardware products are warranted against defects in material and workmanship under normal and proper use The liability of Datalogic under this warranty is limited to furnishing the labor and parts necessary to remedy any defect covered by this warranty and restore the product to it
29. rtain indications such as the pu beep can be disabled using programming barcode la els Re erence the PRG for a more detailed list Indication LED Beeper LED flashes blinks on ia beeps four times Power u pe to view at highest frequency and p USB interface LED blinks until enumeration with pene the hostis completed beep at current fre LED behavior for this indica quency volume Good Read tion is configurable usingthe mono bi tonal setting and PRG duration upon a success ful label scan Imager sounds one error ROM Failure 200ms on 200ms off beep at highest volume for 200 mS Imager chirps six times Scanning at the highest frequency Label Read and current volume Imager Disabled The LED blinks continuously N A 100mS on 900 mS off Quick Reference Guide Programming Barcodes For your convenience this guide includes the programming barcodes required to configure the imager for use with different interface terminal host types See the Product Reference Guide PRG for more complete in formation about programming and configurable features You can download the latest version of the PRG and any other avail able publications for the imager from the website listed on the back cover of this manual Resetting the Standard Product Defaults If you aren t sure what programming optio
30. s normal operating condition Repair or replacement of product during the warranty does not extend the original warranty term Products are sold on the basis of specifications applicable at the time of manufacture and Datalogic has no obligation to modify or y due products once sold If Datalogic determines that a product Tar defects in material or workmanship Datalogic shall at its sole option repair or replace the product without additional charge for parts and labor or credit or refund the defective products duly returned to Datalogic To perform repairs Datalogic may use new or reconditioned parts components subassemblies or products that have been tested as meeting ap plicable specifications for equivalent new material and products Customer will allow Datalogic to scrap all parts removed from the repaired product The warranty period shall extend from the date of shipment from Datalogic for the duration published by Datalogic for the product at the time of pur chase Warranty period Datalogic warrants repaired hardware devices against defects in workman ship and materials on the repaired assembly for a 90 day period starting from the date of shipment of the repaired product from Datalogic or until the expiration of the original warranty period whichever is longer Datalogic does not guarantee and it is not responsible for the maintenance of damage to or loss of configurations data and applications on the repaired units and at its sole dis
31. te lend rent give or otherwise transfer the Datalogic Product to any third party unless such third party agrees with Datalogic in writing to be bound by the terms and conditions of this Agreement Any such transfer of the Data logic Product absent such agreement shall be null and void 3 3 End User may obtain support for Software from Datalogic at Datalogic s standard support fees and under Datalogic s standard support terms and conditions in effect at the time the support is requested 4 Intellectual Property End User acknowledges that the Software constitutes valuable trade secrets of Datalogic or Datalogic s third party licensors and that the Software is protected by intellectual property laws and treaties The license set forth in this Agree ment does not transfer to End User any ownership of Datalogic s or its third party licensors copyrights patents trademarks service marks trade secrets or other intellectual property rights and End User shall have no right to com mence any legal actions to obtain such rights End User shall not remove mod ify or take any other action that would obscure any copyright trademark patent marking or other intellectual property notices contained in or on the Datalogic Product 5 Proprietary Information 5 1 End User acknowledges that Proprietary Information is the confidential proprietary and trade secret property of Datalogic and Datalogic s third party licensors and End User acquires n
32. uide17 001700 NYOSMOIND VNIHO 318V L SHOH ANE BH ES Geuueos pours dn yoo1 Aq Rz ME 9002 69611 L S KIM Sg ET B ERR Gg HR Mel ET a JENANG LE Ed EE Melle MEN xiii uat 9000 69611 LIS 1 E ETE IH Me AY S y ch PEE Eb Ue ch tk A Hl E Ey Le EM o o o o o X pueog Es 0 0 0 HWRE anpon Assy 0 0 0 0 0 K p Me KIME pa Ng pps aga Auaydip 0 6H qd paggumwoagAjog Ainsley pea SHOH EU YI 001200 ue sy ino QuickScan i 18 EUROPEAN DECLARATION OF CONFORMITY SDATALOGIC Datalogic Scanning Inc hereby declares that the apparatus specified below has been tested and found compliant to the following European Council Directives and Harmonized Standards Apparatus QuickScan i Model QD2100 Directives EMC 2004 108 EC Low Voltage 2006 95 EC RoHS 2002 95 EC WEEE 2002 96 EC Standards EN 55022 2006 CISPR 22 2007 AN NZS CISPR22 2008 EN 55024 1998 A1
Download Pdf Manuals
Related Search
Related Contents
HP Color LaserJet CM3530 MFP Series User Guide Dataflex 53.032 flat panel wall mount Clé USB 4GB EMTEC CODi Radiant P-215 Manual del usuario User Manual - Universal Fibre Optics Français - InFocus Copyright © All rights reserved.
Failed to retrieve file