MX6120 Amplifier
Contents
1. Q loads won t hurt the MX6120 but those channels connected to 6 Q loads may occasionally shutdown due to overloading Never ever connect to speaker loads less than 6 Q 7 Individually adjust the channel gains as required Ideally all gains are fully on fully clockwise 8 Make sure the speakers in each room are connected in phase with the amplifier going to the speaker Out of phase speakers give unstable imaging and poor bass response 9 Connect trigger if being used to a 12 VDC source about 35mA using a 3 5mm mono jack 5 VDC triggers will not work 10 Connect the AC power into an outlet that supplies at least EIGHT amps 120 VAC or FOUR amps 230 VAC 1000 watts dedicated to each MX6120 11 This amplifier cannot be mono bridged Caution Never listen to sound that is distorted If distorted sound is heard turn the volume down immediately or speaker and or amplifier damage could occur that is not covered by the warranty If this problem persists contact your dealer User adjustments and service There are no user adjustments on the MX6120 Your installer may make certain gain level adjustments on the rear panel Caution The MX6120 contains no user serviceable parts so do not attempt to open or repair the MX6120 Refer servicing to a qualified technician only or contact the factory for information CAUTION RISK OF ELECTRIC SHOCK WARNING To reduce the risk of electric shock DO NOT OPEN do not expose this appa2. fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used exercise caution when moving the cart apparatus combination to avoid injury from tip over 13 Unplug this apparatus during lightning storms or when not used for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 15 Under no circumstances should the output terminals of the amplifier be short circuited 16 Be sure that the loudspeakers connected can handle the output power of the amplifier at the loudspeakers rated impedance The warranty on the amplifier does not cover damage to loudspeakers that have inadequate power handling capabilities 17 Where an all pole MAINS SWITCH is used as the disconnect device the location on the apparatus and the function of the switch shall be described and the s
3. Warranty Knoll Systems warrants MX6120 amplifiers sold in the USA and Canada by authorized Knoll dealers to be free of defects in materials and manufacturing This warranty extends for three full years from the date of purchase by the original consumer Any products returned to Knoll Systems and found to be defective by Knoll Systems within the warranty period will be repaired or replaced at Knoll Systems decision at no charge Knoll Systems will not be responsible for the actual cost of installation or removal of the product nor for any incidental or consequential damages Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation may not apply to you This warranty gives you specific legal rights You may have additional legal rights that vary from state to state Specifications Line Inputs 6 Gold RCA jacks with adjustable gain Input impedance 50k Q Outputs detachable plug Output power Line Outputs Peak output power Ideal impedance Frequency response S N ratio THD distortion IMD distortion Trigger control Dimensions Fan Noise Power Weight 120 watts RMS per channel 8 Q 6 Gold RCA jacks unbuffered 180 watts per channel 8 Q 8 Q 10 Hz 40 kHz 1dB iw over 108 dB A weighted 100 watts less than 0 1 20 Hz to 20 kHz less than 0 01 60 Hz 7 kHz 4 1 SMPTE 12 VDC 35mA on 3 5mm mono jack 17 x 3 5 x 11 5 432 x 89 x 292mm quiet 26 dBA 900 w
4. atts at 117 VAC or 230 VAC 21 Ibs 9 5 kg Note Specifications subject to change without notice Knoll Systems 145 Tyee Drive Point Roberts WA 98281 14 7163 Vantage Way Delta BC V4G 1N1 Tel 604 940 1689 fax 855 734 3363 Made in Canada Fabrique au Canada MX6120 Amplifier i knoll Warning To be installed and or used in accordance with appropriate electrical codes and regulations FOR USE WITH 6 16 OHM SPEAKERS ONLY Description The MX6120 is a member of the long line of Knoll multi channel amplifiers Designed primarily for the custom install industry it is used to power speakers with different or similar sources in multiple rooms With 6 channels rated at 120 watts per channel at 8 Q the MX6120 packs some serious punch Each channel has a gain control The MX6120 can be turned on and off via the front panel power switch or via the 12 VDC trigger 1 3 MX6120 stereo channels can be connected to a line level BUS input MX6120 amplifiers designed to meet the amplifier needs of custom installed systems where high quality sound is a specific requirement Installation Instructions v1 0 Key Features 1 Size efficiency The MX6120 consists of a total of 6 high power amplifiers in one 3 1 2 high enclosure Each power amplifier channel can deliver 120 watts RMS into an 8 Q load 2 Automatic protection circuitry Each MX6120 channel is individually and fully protected against low impedance overheating overloadin
5. de in full compliance with all local building safety and electrical codes Knoll Systems service information The MX6120 amplifier does not contain any user serviceable parts inside If you suspect a problem that may require servicing contact us at www knollsystems com contact html or by phone at 604 940 1689 Troubleshooting If a problem is encountered with the MX6120 the most expedient procedure is to locate the problem and if possible repair it before requesting service Be sure to carefully check other system components such as controllers CD players volume controls wiring speakers etc that may be at fault Problem Action Power LED does 1 Check that the MX6120 is plugged in not light no sound 2 Test the AC outlet with a lamp 3 If remote on off is used check that the trigger voltage is at 12 VDC 4 Check MX6120 power button on in Sound cuts out 1 Verify speaker impedance is 8 16 Q Changing speakers may be required 2 Check if the MX6120 feels hot If it s hot increase cooling see Installation Turn the volume down Check speakers for damage Check inputs for proper levels MX6120 gain and source output level may have to be adjusted 4 Speakers may be less than 8 Q Sound is distorted WN e MX6120 does Push MX6120 power switch off out not turn off 2 If trigger is being used power switch needs to be set to off out position Or amp is on all the time 3 Try disconnecting trig
6. g over voltage and under voltage The protection circuitry automatically restores the amplifier channel as soon as its parameter returns to the safe operating area 3 Individual input gain adjustment Each channel features an input gain adjustment pot to adjust each channel for gain and speaker sensitivity variations 4 External power on off The MX6120 can be turned off and on by external controllers via its 12 VDC trigger jack 5 Stackable 17 chassis 19 rack ears available 6 Bus Feature Certain installations require that some or all of the stereo channels play the same content Instead of using Y cords the Knoll BUS connects any or all of channels 1 3 to the stereo BUS inputs Important Safety Instructions 1 Read these instructions 2 Keep these instructions 3 Read all warnings 4 Follow all instructions 5 Do not use this apparatus near water 6 Clean only with dry cloth 7 Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prongs are provided for your safety If the provided plug does not
7. ger jack Trigger does not 1 Measure the trigger voltage with a volt work meter It needs to be 11 15 volts DC to work current is about 35mA total per amp See page 5 for details Speaker pops when 1 Speaker may need resistor placed amp turned on or off across terminal Suggest 2k0 Q 1 w Discharges speaker internal capacitor Installation Installing the MX6120 should be relatively easy With a bit of planning it will give trouble free service for years 1 The most important consideration when installing the MX6120 is cooling The MX6120 has a lot of power packed into a small chassis size When installing it in an equipment stack it should be the top component It needs at least 3 5 of space above the amplifier to allow for adequate convection cooling 2 Amplifiers should always be the top components in the system 3 If MX6120 channels frequently shutdown due to overheating install a fan directed up from the MX6120 bottom center 4 Never operate the MX6120 on its side as the cooling potential drops significantly when operated this way 5 Connect the MX6120 inputs to the source component outputs with good quality short as possible RCA jack cables Connect each channel individually 6 Connect the MX6120 speaker outputs to speakers using good quality speaker wire Minimum 16 gauge copper wire is recommended with 14 gauge minimum for runs over 30 10m Note Ideally the MX6120 likes 8 16 Q loads Connecting to 6
8. ponents in your system and then disconnect the input cables at the amplifier Turn the amplifier back on to see if the hum is still present If the hum disappears the fault may be in the input cables used Try replacing them with cables that have better shielding and make certain that the input cables are not running on top of any AC power cords Change the cables one at a time to determine if one or all cables are responsive If the hum disappears when the input cables are disconnected but returns after the cables are changed and the system reconnected your source device may be causing the problem Suggestion 3 Poor grounding of the electrical system in your home may also cause ground loop problems particularly when there are multiple components with three prongs grounded power cords Unplug these components one at a time and see if one or all of them is causing the problem The ultimate solution to this type of problem is to rewire your house with an isolated star type grounding configuration Knoll understands that this may be impractical and expensive In some instances the use of an approved AC power isolation transformer of sufficient capacity may solve this problem Warning If you suspect that the grounding system in your home s electrical wiring is causing the hum problem it is important that you do not make any changes to the wiring Only a licensed electrician should make any changes to household wiring and they must be ma
9. ratus to rain or moisture Wi a ie ey it E The trigger is 12 VDC 35mA per MX6120 via 3 5mm mono jack 5 VDC trigger outputs will not work To connect the trigger to a receiver use a 12 VDC power supply we suggest Knoll PS1205 power supply with an adaptor Plug the power supply into the switched outlet on the rear of the receiver Connect the 12 volt wire to a 3 5mm mono jack Plug the jack into the rear of the MX6120 12 VDC polarity is not important Make sure the MX6120 power switch is off out When the receiver is switched on the MX6120 amplifier is switched on Made in Canada Fabrique au Canada l Class 2 Knoll Systems Point Roberts WA a cman MX6120 Deseme so Bc The Line Bus button is normally set to the in position to give all three stereo inputs individual sources When the BUS button is set to the out position that channel stereo input is connected or paralleled to the BUS INPUT without the use of Y cords Any or all combination of BUS inputs 1 to BUS inputs 3 are possible When all inputs are connected to the BUS INPUT the input impedance is about 15 000 Q Caution NEVER connect the MX6120 to impedances less than 6 or amplifier damage not covered by the warranty may occur Made in Canada
10. witch shall remain readily operable 18 A push button is used to turn the power off and on 19 A LED is used to show when the apparatus is powered on CAUTION These servicing instructions are for use by qualified service personnel only To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so WARNING This product may contain chemicals including lead Known to the State of California to cause birth defects or other reproductive harm Wash hands after handling Hum and noise In most cases one of the following suggestions should help you solve a hum noise in your system Please try these steps in the order shown proceeding from one step to the next if the prior suggestion does not eliminate the problem Suggestion 1 To determine if a cable TV connection is responsible for the hum first turn off all the components Disconnect the cable TV feed to your system at the first place where it connects to your components Alternatively disconnect the cable TV wire where it is connected at the wall outlet Turn your system back on and listen if the hum has disappeared If removing the cable TV feed has eliminated the hum you will need to insert a Ground Loop Isolator Knoll model GB634 before reconnecting the cable TV feed or contact your cable TV operator to see if they can better isolate your cable feed Suggestion 2 Turn off all com
Download Pdf Manuals
Related Search