User Manual
Contents
1. BRIGHTNESS Brightness 0 255 CONTRAST Contrast 0 255 SHARPNESS Sharpness 0 255 A high value of sharpness could increase the noise level HUE Hue 0 255 GAIN Gain 0 255 Setting for the maximum internal gain value 30 ATR Settings for the Wide Dynamic Function Adaptive Tone Reproduction OFF Wide Dynamic Function deactive ON Wide Dynamic Function active LUMINANCE LOW MID HIGH Level of the brightness balance Dark areas will be displayed more bright LOW gt HIGH in addition the brightness for bright areas will be tried to keep constant CONTRAST LOW MIDLOW MID MIDHIGH HIGH Increasing of image contrast LOW gt HIGH A high value can cause detail loss in dark areas as well as over exposure PRIVACY PRIVACY Privacy masking function of up to four zones free to configure OFF Privacy masking function deactive ON Privacy masking for all four zones is active AREA SELECT 1 4 4 4 Zone selection TOP 0 288 Top limit for the selected area BOTTOM 0 288 Bottom limit for the selected area LEFT 0 468 Left limit for the selected area RIGHT 0 468 Right limit for the selected area COLOR 1 8 Red 1 light green 2 blue 3 green 4 light blue 5 purple 6 white 7 black 8 TRANSP 0 0 1 00 Transparency of the masking MOSAIC OFF ON Mosaic display for the privacy masking The impression of unsharp areas will be produced for masked areas The effect is at best at TRANSP2. It must be assumed that safe operation is not longer possible if the device shows visible signs of damage the device no longer operates and has been stored for longer periods under unfavorable conditions or has been subjected to considerable stress in transit Please note The product is absolutely maintenance free for you There are no components on the inside of the product to be checked or services by you never open it 7 2 Cleaning Clean the product with a clean soft cloth To remove severe contamination the cloth can be dampened with luke warm water Make sure that no liquids can enter the equipment as the device can be destroyed Never use chemical detergents as they could attack the surface of the device 8 Disposal Products which are labeled with this pictogram may not be disposed by the domestic rubbish Please dispose the product in accordance with the prevailing legal regulations at the end of its life time Please consult your dealer or dispose the product over the municipal gathering point for electric scarp 33 9 Technical data DSP J Sony Effio E 1020 H x 596 V 976 H x 582 V riri da Illumination 0 Lux F1 2 IR extern 0 Lux Q F1 2 IR cut filter removable IR cut filter removable Day night ICR Color B W ICR Color B W ARES o ps 24LEDs 850mm CET 33 10 20m Automatic gain control AGC 28dB max Backlight compensation IP34 2 x FBAS 1
3. 0 00 RETURN Back to main menu 31 Settings for the noise reduction 2D DNR OFF Noise reduction deactivated NR MODE Y C Y C Y Noise reduction for luminance signal C Noise reduction for chroma signal Y C Combination of Noise reduction for luminance and chroma Y LEVEL 0 15 Level for the noise reduction of luminance C LEVEL 0 15 Level for the noise reduction of chroma RETURN Back to main menu Camera ID Function Description 1 CAMERA ID Camera description OFF No display of the camera description in the live image ON Display of the camera name with dedicated location The camera description length is max 26 digits lt gt Control keys for this sub menu CLR By selection and pressing the Enter key the selected digit will be deleted POS By pressing the Enter key the positioning mode will be activated Use the control keys to change the position of the name By pressing Enter once again the sub menu will be left CAMERA RESET Function Description gt Z 1 1 CAMERA RESET Restore the default camera settings 32 7 Service and cleaning 7 1 Function test Check the technical safety of the product such as damage to the housing at regular intervals When it can be assumed that the safe operation is no longer possible the product must be put out of service and precautions taken o ensure that it is not used unintentionally
4. guarantee for the content of this document is taken 20 Important safety instructions The warranty will expire for damage due to non compliance with these operating instructions We shall not be liable for any consequential loss We do not accept liability for damage to property or personal injury caused by incorrect handling or non compliance with the safety instructions In such cases the warranty will expire Dear customer The following safety instructions are intended not only for the protection of your health but also for the protection of the device Please read through the following points carefully There are no parts on the inside of the product which need to be serviced Apart from this the license CE and the guarantee warranty will lapse if you open take the product apart The product will be damaged even it falls from a low height This device can be used in inside as well as outside During the installation of the camera please take care that direct sunlight cannot fall onto the image sensor of the device Please follow the installation instructions in the corresponding chapter of this user manual Avoid using the device under the following unfavorable ambient conditions wetness or excessive air humidity extreme cold or heat direct sunlight dust or combustible gases vapors or solvents strong vibration strong magnetic fields such as those found in the vicinity of machinery or loudspeakers the camera shou
5. in the triangle points to an important note in this user manual which must be minded This symbol can be found when you are to be given tips and information on operation 3 Scope of delivery 650 TVL dome camera Installation material screws pegs DC 2 pin adapter User manual 4 Features and functions State of the art EFFIO chip set with WD function for clear images even at high contrast ratios DNR function for noise free images Integrated 2 8 10 5 mm variofocal lens High resolution of 650 TV lines Easy Plug camera module and mounting plate for quick installation Triaxial camera holder Auto IR LED function for automatic adjustment of the LED performance TVCC70500 23 5 Description of device 5 1 Overview item numbers TVCC70000 TVCC70500 650 TVL 650 TVL 2 8 10 5 mm 2 8 10 5 mm o IR Ya Day Night removable IR cut y y filter 12 VDC 12 VDC 5 2 Unpacking While you are unpacking the device please handle it with utmost care If you notice any damage of the original packaging please check at first the device If the device shows damages please contact your local dealer 6 Mounting Attention i Please disconnect the camera from power supply during the installation 6 1 Mounting of the camera Surface mounting Before removing the dome head the dome head fixing screw must be removed as factory default the screw is supplied in the package The dome head now can be removed by anti c
6. so that the 15 pin socket and plug position will match At the opposite side of the 15 pin joint the module will be hold in position by two fixing bars In case socket and plug will match please press the camera module on both outside handles in direction of the base part until the 15 pin joint is fully latched Please screw the two fixing screws for the camera module back The dome head and dome head ring will be fixed on the camera bottom part by clockwise rotation Please use the supplied fixing screw to fix the dome head dome head ring position Attention h Please disconnect the camera from power supply during the installation 6 2 Connectors Before you start with the installation please make sure that the supply voltage and the nominal voltage of the camera comply together Power supply amp video signal Video output for service purpose Video output prim ry BNC female FBAS 1Vs s Power connector round plug 5 5x2 1mm 12 VDC or DC 2 pin adapter Videoausgang sekund r Service Cinch female FBAS 1Vs s CO N 26 6 3 Camera module adjustment The camera module can be adjusted in 3 axis The adjustment of the third axis often will be used on wall mount of the camera The module rotation 1 and 3 axis must not be performed more than 360 degree Pan 1st axis Tilt 2nd axis Rotation 3rd axis 6 4 Fokus und Zoomeinstellung The cameras TVCC70000 and TVCC70500 are equipped with a va
7. HT PICT ADJUST ATR PRIVACY NR CAMERA ID CAMERA RESET EXIT SAVE ALL Funktion j Beschribung O General image settings ATR Adaptive Tone Reproduction Settings for the Wide Dynamic Function AN EXIT Leaving the OSD menu SAVE ALL Save all changed values 29 White Balance WHITE BAL Function ATW Auto Tracking White Balance pe The setting for the white balance function will be performed dynamically and continuously in the range of 1800 10500K Continuous setting for the white balance with limitation of color temperature range USER1 User 2 User defined white balance R GAIN 0 255 Red value Optimized white balance settings for fluorescent light to avoid cross color effects MANUAL Manual white balance B GAIN 0 255 Blue value R GAIN 0 255 Red value PUSH LOCK Push Lock BM The white balance measurement will be performed by pressing the Enter button on the control board and will be stored BACKLIGHT The back light handling is turned off The conventional back light compensation function is activated Back Light Compensation The function for inversion of too bright image areas into black color is activated High Light Compensation Too bright image areas will be converted to black areas over certain value e g car lights PICT ADJUST MIRROR Horizontal mirror OFF Horizontal image inversion is deactive ON Horizontal image inversion is active
8. V s s 75 Ohm BNC Cinch 5 5x2 1mm DC 10 C 50 C ER 34
9. eyseo Security Tech Germany WD DNR Day Night Vario 650 TVL Dome camera TVCC70000 Version 12 2010 TVCC70500 Original English user manual Keep for future use 19 Introduction Dear Customer Thank you for purchasing this product This product meets the requirements of the applicable European and national guidelines The corresponding declarations and documents can be obtained from the manufacturer www abus sc com To maintain this condition and to ensure risk free operation you as the user must observe these operation instructions Before initial start up read through the complete operating instructions observing operating and safety instructions All company and product names mentioned in this document are registered trademarks All rights reserved If you have any questions please contact your installer or your local dealer Disclaimer This user manual was prepared with greatest care If you should notice omissions or inaccuracies please inform us about these on the back of this manual given address The ABUS Security Center GmbH amp Co KG assumes no liability for technical and typographical faults and reserves the right to make at any time modifications to the product or user manual without a previous announcement The company is not liable or responsible for direct and indirect subsequent damages which are caused in connection with the equipment the performance and the use of this product No
10. ld not positioned with opened iris towards the sun this can lead to the destruction of the sensor the camera may not be installed on unstable surfaces General safety instructions Do not leave packaging material lying around carelessly Plastic foil oags and polystyrene parts etc could become dangerous toys for children For safety reasons don t give the camera into child hands due to them being able to swallow small parts Please do not insert objects through the openings into the device Use only accessories which are specified by the manufacturer Please do not connect incompatible parts to the device Please pay attention to the safety instructions and user manuals of the other connected devices Check the device for damages before installation If this should be the case please do not use it Please adhere to the operational voltage limitations listed in the technical data High voltage could destroy the device and pose a health hazard electric shock During the installation into an existing video surveillance system make sure that all devices are disconnected from the low and supply voltage circuit 21 make do electrical connection to the mains does only represent at threat to you but also to other If in doubt allow a professional electrician to mount install and wire up your device Improper or m o d Ic persons Wire up the entire system making sure that the mains and low voltage circuit remain separated and cannot c
11. lockwise rotation 24 For this camera type the camera module can be removed and it is fixed by two fixing screws Base part of the camera and camera module are connected by a 15 pin D Sub joint Unscrew the fixing screws and carefully remove the camera module Place the base part to the desired installation position mark the holes for fixing on the surface and drill the fixing holes Use the supplied screws and pegs to fix the base part on the surface The cable rounting can be done to the side or throught the base Flush mounting For flush mount of this analog indoor dome camera an optional flush mount bracket is available TVAC31010 First remove the base cover ring by using a thin flat screw driver Carefully move the screw driver into the small openings at the outside of the dome bottom part and push the screw driver to the center of the dome image marking 1 2 83 The 3 fixing elements will be loose now and the base cover ring can be removed carfully Now drill a hole of 124 mm into the ceiling panel max 130 mm Plase the flush mount bracket Pm onto the ceiling panel and move the camera e m bottom part into the hole Please use the supplied screws to fix the camera bottom part e with the ceiling mount bracket see image B The cable routing will be performed through the pu ceiling ss E 25 Installation of the camera module Bring the camera module close to the base part
12. ome into contact with each other in normal use or due to any malfunctioning Table of contents IER IPIZRE II P 23 EXPLANATION OF SYMBOL 1 erro eren rennen nhanh rara hara eR E REA SR SROREAR IRR A ARORSES 23 SCOPE OF DELIVER Yana iria 23 FEATURES AND FUNCTIONS coooccccccccncnnnncnonannnnnnonannnnonanannnnnnannnnnnenannnnnnnnanannenananannnnananannanananas 23 DESCRIPTION OF DEVICE 0 u cccsccccecssnscecnsnsnscecnsnsescennensescnnnsnscncnensnsenenensesenenensesenensnsenenensass 24 5 1 OVERVIEW ITEM NUMBERS ccscececcecececcccccececcccecececaucececcaucecsceausecseeaetscstaueusscavaeserseeeaess 24 e UNPACKINO E E dd ii ida cebada 24 MOUNTING aaee tasas 24 6 1 MOUNTING OF THE CAMERA cccccececcccecececcccececccecececuucececeecusececseuausecauaususecsuaeausereeaesesseaeaess 24 AONNE OIO nie 26 6 3 CAMERA MODULE ADJUSTMENT ccecececececececcccccccccaccecececececececeneaeaeatecececeteceneneueavavsnstseenenenes 27 6 4 FOKUS UND ZOOMEINSTELLUNG cccccecececcecececcccececcccccececaccucecseceausecseauacuesscauaecstsceuaesersvaees 27 6 5 ADJUSTMENT OF IR LED INTENSITY AND CAMERA PARAMETER sscececcecccececcececececcececeecaees 28 6 6 INSTALLATION OF THE DOME HEAD ccccccececcecececccececcccccececcaucecseueaesecseauaceecseaesesersvausesersnaees 28 6 7 CAMERA PARAMETER OSD MENU esssssseeseeeeeene nennen nnnnn nnns na nnn
13. rio focal lens On the bottom side of the lens two adjustment handles for focus and zoom ratio are positioned The handles additionally act as a fixing screw for the focus and zoom adjustment The fixing handles can be rotated anti clockwise for defixing Please perfom this with care to prevent the handles falling off the lens Now please adjust zoom ratio and focus Afterwards fix the handles by rotating clockwise Description Option Zoom ratio adjustment WIDE Viewing angle wide Zoom Ox max TELE Viewing angle narrow Zoom 3 75x max Focus adjustment FAR Focus far NEAR Focus near 2 6 5 Adjustment of IR LED intensity and camera parameter 1 IRIS ADJ Adjustment of the aperture of the auto iris lens 2 IR intensity 2 levels for the IR light intensity are available HI 20 meter LOW 10 meter 3 Setup of camera parameter over control keys OSD menu TVCC70000 TVCC70500 6 6 Installation of the dome head The dome head with dome head ring will be placed onto the base part in a specific position Please take care that the hole for the side fixing screw will be placed near the opening fort he cables The dome head ring will be fix by 3 handles on the base part and it will be fixed by clockwise rotation onto the base part Please use the supplied fixing screw to fix the dome head dome head ring position 28 6 7 Camera parameter OSD menu SETUP MENU WHITE BAL BACKLIG
14. s nna nnns nsa rrr sana nnns nns 29 SERVICE AND CLEANING ceceneur nnne nnn hu nun h naa RR DR RR RR DR RRRRSRR RENE RR Rau RORaA 33 TED FUNG TION TES NC TRRTRCK Mn 33 yeu OGLEANING enredos dt adas 33 DISPOSAL ccccccccecesescecececcscucecescscncnsecncucnseeeneecescseneusesnseeenseeaeseeaseeseeuensaseneuseseseneuseeeeauensseneaseess 33 TECHNICAL DATA snoot ee ee ree 34 22 1 Intended use The 650TVL dome camera is equipped with a high quality image sensor It is used for video surveillance in internal areas in connection with a recorder or monitor You can find a detailed description of functions in section 4 Features and functions The product should not become damp or wet The camera is only for use in dry indoor areas addition involve other risks This does not include operation for other applications Any other use than that described above can lead to damage to the product and in and would in case of doing so the guarantee and any related liability will lapse This is also the case if any unauthorized changes or additions have been made to the product Please read through the entire manual carefully before putting this product into operation This operating manual contains guidelines that are important for correct mounting and operating 2 Explanation of symbol OPE A flash in the triangle is used if there is danger for the health e g by an electric shock An exclamation mark
Download Pdf Manuals
Related Search