Quick Installation Guide
Contents
1. A Control Panel nm e LED Status oo Function Indication Keys Off Printer power off PAUSE Pause Resume the printing process 1 Enter the menu i i MENU 2 Exit from a menu or cancel a On Printer is ready setting and return to the previous Printer is paused menu POWER On Printer power on ON LINE EE Blinking Printer is downloading FEED Advances one label data UP Scroll up the menu list L 3 SELECT Enter Select cursor located option 2 ey Primer i ready DOWN Scroll down the menu list rause a up On Carriage open or Busu saser ERROR cutter error Lr reep v vow Blinking No paper paper jam or no ribbon Media Sensor Calibration The media sensor should be calibrated whenever changing the label media or after printer initialization Please follow the steps below to calibrate the media sensor 4 Adjust the rear label guide green 5 Adjust the front label guide green 6 Move the media sensor by adjusting to fit the label width to fit the label width the media sensor position adjustment knob make sure the gap or black mark sensor is at the location where media gap black mark will pass through for sensing Method 1 by keys 1 Make sur2. media has been loaded properly as described above 2 Tap the Menu icon to enter the main menu and tap the gt icon to enter the next page 3 Tap the Diagnostic icon to enter this setting list and tap the Print Config item to print out the self test page P N 39 0510001 00LF
3. Quick Installation Guide Printer Overview Fan fold paper entrance chute Graphic LCD with back lit display Paper exit Media view Power jack chute window socket Note ae es External BlueTooth or WiFi module Option interface USB host x 2 Power switch Rear Option RS 232C GPIO interface Option Centronics interface The interface picture here is for reference only Please refer to the product specification for the interfaces availability Printer cover Ribbon supply Print head pressure adjustment knobs Print head Platen roller Media Media sensor Front label spindle sensor auld position adjustment Label supply Ribbon knob spindle guide bar j Ribbon A Ribbon sensor i rewind 2 spindle y o s i o i B DRIA Print head Oo OO release lever Internal rewind Peel off roller Rear label pep Neste spindle Option release lever guide Front Option Label guide bar release lever Loading the Ribbon Install the ribbon and paper core onto ribbon supply spindle and ribbon rewind spindle 2 Push print head release lever to open print head mechanism Thread ribbon above the ribbon guide bar and th
4. e the ribbon and label media are installed properly as described above 2 Press the MENU button and press the SELECT button to enter the main menu 3 Press DOWN button to select the Sensor option and press SELECT button to enter this option 4 Select the Auto Calibration item and press the SELECT button to enter this option 5 Press UP or DOWN button to select the media type and press the SELECT button to calibrate the selected media sensor automatically Method 2 by touch display 1 Make sure the ribbon and label media are installed properly as described above 2 Tap the Calibration icon to enter this option and tap the media type to calibrate the selected media sensor Loading path for media 7 Close print head release lever and label guide bar release lever automatically Printer Initialization Printer Initialization will restore printer settings to defaults Please follow the steps below to initialize the printer Method 1 by keys 1 Press the MENU button and press the SELECT button to enter the main menu 2 Press DOWN button to select the Service option and press SELECT button to enter this option 3 Select the Initialization item and press SELECT button 4 Select Yes item and press SELECT butt
5. on to restore printer settings to defaults Method 2 by touch display 1 Tap the Menu icon to enter the main menu and tap the gt icon to enter the next page 2 Tap the Service icon to enter this setting list and tap the Initialization item 3 Tap Yes item to restore printer settings to defaults Printer Self test Self test printout is used to check if there is any heater element damaged on the print head and shows current printer configurations Please follow the steps as below to perform printer self test 8 Set media sensor type and calibrate the selected sensor Please refer to the Media Sensor Calibration on facing page to calibrate the sensor Note Re calibrate the gap black mark sensors when changing media Method 1 by keys 1 Make sure the media has been loaded properly as described above 2 Press the MENU button and press the SELECT button to enter the main menu 3 Press DOWN button to select the Diagnostic option and press SELECT button to enter this option setting list 4 Select the Print Config item and press SELECT button to print out the self test page For more information and features about this printer please refer to the user s manual on the CD disk Specifications accessories parts and programs are subject to change without notice Page 2 of 2 Method 2 by touch display 1 Make sure the
6. rough ribbon sensor slot Please refer to Loading path for ribbon as 3 following fig L sO 4 Stick ribbon onto ribbon rewind paper core keeping the ribbon flat and wrinkle free counterclockwise roughly 3 5 circles until ribbon is smooth properly stretched and wrinkle free 6 Close the print head mechanism by pushing the print head release lever Loading path for ribbon Ink coated outside wound Ink coated inside wound i O Oe PWO I i Vee Ope oS o O67 90 o Page 1 of 2 Loading the Media al 2 Push open the print head release 3 Pull the leading edge of the label lever and label guide bar release forward through the media guide bar lever for loading media pass media sensor and place the leading edge onto the platen roller D 1 Open the printer right side cover Place the roll of media on the label supply spindle adl ete 50 0 GAP a White ya ae A aa a aa a w TRIAN a i
Download Pdf Manuals
Related Search