WS-GB Laser
Contents
1. works in sync with the music To determine the power requirements for a particular fixture see the label affixed Mic Knob To detect the music sound signal to the back plate of the fixture of refer to the fixture s specifications chart A Used to attach a safety cable when the fixture Bon ara _ Safety Eye a fixture s listed current rating is its average current draw under normal conditions is rigged All fixtures must be powered directly off a switched circuit and cannot be run off a Interlock Switch To interlock laser diodes output rheostat variable resistor or dimmer circuit even if the rheostat or dimmer LED Display Board To display operation menu channel is used solely for a 0 to 100 alae PEIR applying power to a fixture DMX Output Spins female AiR connector check that the source voltage matches the fixture s requirement The unit is supplied with a power plug appropriate to its voltage and destination DMX Input 3 pins male XLR connector Should any other connections be required they must be carried out with the following configuration USER MANUAL PRODUCT OVERVIEW This device has left out premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation it is necessary for the user to follow the safety instructions and warning notes written in this manual The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or2. AUTO SHOW 150 255 DMX MODE 0 115 Clockwise fast to slow CH2 MOTOR A SPEED 140 255 Anticlockwise slow to fast CH3 0 19 Stop MOTOR B SPEED 20 255 Slow to Fast 13 USER MANUAL LASER SAFETY WARNINGS Potential laser injury hazard exists with this product Read these instructions carefully which includes important information about installation safe use and service AN Caution Avoid direct eye contact with laser light Never intentionally expose your eyes or others to direct laser light AN Caution This laser product can potentially cause instant eye injury or blindness if laser light directly strikes the eyes AN Caution It is illegal and dangerous to shine this laser into audience areas where the audience or other personnel could get direct laser beams or bright reflections into their eyes AN Caution It is a US Federal offense to shine any laser at aircraft A Caution _ here are no user serviceable parts inside the unit Do not open the housing or attempt any repairs yourself In the unlikely event your unit may require service please contact the dealer nearest to you A N Caution Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure Every person involved with installation and maintenance of this device has to Be qualified Follow the instructions of this manual CAUTION Be careful with your operati
3. any unauthorized modification to the device Front Panel i kd POWER MUSIC Laser Aperture Laser effect output aperture USER MANUAL FUSE 5mmx20mm FUSE F 1 A 250V caeu cabs Pn mrt Brown Black Live Light blue White Neutral DMX 512 connection between fixtures The fixture is equipped with 3 pin XLR sockets for DMX input and output The sockets are wired in parallel Only use a shielded twisted pair cable designed for 3 pin XLR plugs and connectors in order to connect the controller with the fixture or one fixture with another Occupation of the XLR connection DMX output DMX input XLR mounting sockets rear view XLR mounting plugs rear view 1 Shield 2 Signal 3 Signal A Caution At the laser fixture the DMX cable has to be terminated with a terminator Solder a 120 Ohm resistor between Signal and Signal into a 3 pin XLR plug and plug and plug it in the DMX output of the last fixture PIN 3 PIN 2 USER MANUAL USER MANUAL Building a serial DMX chain Rigging the Fixture Hy L 9 0 TN ae n I DMX 512 1209 Controller operation H Master slave t L ga Doo t operation 1209 1209 If you are using the standard DMX controllers you can connect the DMX output of the controller directly with the DMX input of the first fixture in the DMX chain If you wish to connect DMX controllers with other XLR outputs you need to use ad
4. Laser Medium DPSS Nd YVO4 532nm Blue Laser Medium DPSS 450nm Beam Diameter lt omm at aperture Pulse Data All pulses lt 4Hz gt 0 25sec Divergence each beam lt 2mrad Divergence total light lt 160 degrees Laser Power Blue gt 300mW Green gt 50mW AS measured under IEC measurement conditions for classification LASER COMPLIANCE STATEMENT According to the EN 60825 1 1994 A1 2002 A2 2001 COTT regulations this laser fall under the classification 3B Direct eye exposure can be dangerous USER MANUAL USER MANUAL BEFORE OPERATION Rear Panel Unpacking Instructions A N CAUTION Immediately upon receiving a fixture carefully unpack the carton check the contents to ensure that all parts are present and have been received in good condition Notify the shipper immediately and retain packing material for inspection if any parts appear damage from shipping or the package itself shows signs of mishandling Save the package and all packing materials In the event that a fixture must be returned to the factory it is important that the fixture be returned in the original factory box and packing What is included i ON Twld4dS The carton or flight case contain following items PT NAME QTY DESCRIPTION Power Supply With IEC socket and integrated fuse holder 1pc Power Switch Switch ON and OFF the fixture Turn the knob potentiometer until the laser Power Supply Sensitivity Knob
5. USER MANUAL surroundings can cause greater accumulation of dirt on the unit s optics 1 Clean with a soft cloth using normal glass cleaning products 2 Always dry the parts carefully 3 Clean the Aperture glass at least once every 30 days The interior of the fixture should be cleaned annually using a vacuum cleaner or air jet ATTENTION We strongly recommend internal cleaning to be carried out by qualified engineer SPECIFICATIONS Fuse 250V 1 5A slow blow 20mm glass Music Control Internal microphone Laser Power 50mW Green laser I 532nm 300mW Blue laser 1 450nm Laser Safety Standard EN60825 1 2007 220mm 180mm 80mm Specifications subject to change without prior notice The availability of particular products may vary by region Please check with the dealer 15 USER MANUAL WS GB Laser This manual contains important laser system safety and operation information Read and understand all instructions prior to powering on laser unit the first time to avoid laser eye injury and to avoid breaking the law Keep this manual in a safe place for future reference USER MANUAL WARNING Lasers can be hazardous and have unique safety considerations Permanent eye injury and blindness is possible if lasers are used incorrectly Pay close attention to each safety REMARK and WARNING statement in the user manual Read all instructions carefully BEFORE operating this device This unit contains high pow
6. apter cables Connect the DMX output of the first fixture in the DMX chain with the DMX input of the next fixture Always connect output with the input of the next fixture until all fixtures are connected If you use a controller with 5 pins DMX connector you need to use a 5 to 3 pins adaptor At last fixture the DMX cable has to be terminated with a terminator Solder a 120 Ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pins XLR plug and plug it in the DMX output of the last fixture Connect the fixture together in a daisy chain by XLR plug cable from the output of the fixture to the input of the next fixture The cable cannot be branched or split to a Y cable DMX 512 is a very high speed signal Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the system The DMX output and input connectors are pass through to maintain the DMX circuit when power is disconnected to the unit Each fixture needs to have a DMX address to receive the data from the controller The DMX address number which could be read from rear panel of each fixture is between 000 511 The end of the DMX 512 chain should be terminated to reduce signal errors CAUTION Please consider the respective national norms during the installation The installation must only be carried out by an authorized employee or dealers The installation of the fixture has to be built and constructed in a way t
7. er laser devices internally Do not open the laser housing due to potential exposure to unsafe levels of laser radiation The laser power levels accessible if the unit is opened can cause instant blindness skin burns and fires The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorized modification to the device A Caution Prevent damage or injury from incorrect operation A Laser Laser safety warning labels nr l l Qaae Recycle To protect the environment recycle packing material wherever possible 3 Indoor The projector is for indoor use only IP20 Use only in dry locations Keep this device away from rain and moisture excessive heat humidity and dust Do not allow contact with water or other fluids R Disposal Don t throw this product away just as general trash please dispose of this product following the abandon electronic product regulations in your area g Location The projector must be installed in a location with adequate ventilation at least 50cm 20 inches from adjacent surfaces Be sure that no ventilation slots are blocked USER MANUAL 121 160 Green strobe blue not strobe 161 200 Blue strobe Green not strobe CH6 STROBE SPEED 251 255 Strobe by sound CH7 0 255 Slow to Fast GRATING SPEED a CH8 GRATING DIRECTION 161 255 Anticlockwise MAINTENANCE Make sure the area below the installation place i
8. hat it can hold 10 times the weight for 1 hour without any harming deformation The installation must always be secured with a secondary safety attachment e g an appropriate catch net This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails Make sure the area below the installation place is free from unwanted persons during rigging de rigging and servicing The operator has to make sure that safety relating and machine technical installations are approved by an expert before taking into operation for the first time and after changes before taking into operation another time The operator has to make sure that safety relating and machine technical installations are approved by a skilled person once a year The fixture should be installed in the position where persons cannot reach and where persons may walk by or be seated CAUTION When installing the device make sure there is no highly in inflammable material decoration articles etc in between a distance of min 0 5 meter
9. oblems stop using the fixture and contact your dealer immediately Attention Laser will be output from laser aperture in 5 seconds after the unit is powered on Operating Mode When laser is powered on LED monitor on rear panel shows the current operating standalone mode or DMX address of DMX mode With help of LED control panel it is very easy to set and change the operating mode of laser After every resetting and saved the new mode information will be shown on LED monitor at next power on Mode Function Option to choose the operating mode of laser ENTER Confirmation to confirm all setting or change of LED control panel UP DOWN to change operating mode parameter or DMX address Stand Alone Preprogram Laser Show Press FUNC to enter MODE OPTION Press UP or DOWN to select your favorite Stand Alone mode as above Press ENTER to confirm the setting 11 USER MANUAL LASER EXPOSURE WARNING LASER LIGHT AVOID DIRECT EYE EXPOSURE Further guidelines and safety programs for safe use of lasers can be found in the ANSI 2136 1 Standard For Safe Use of Lasers available from www laserinstitute org Many local governments corporations agencies military and others require all lasers to be used under the guidelines of ANSI Z136 1 Laser Display guidance can be obtained via the International Laser Display Association www laserist org LASER EMISSION DATA Laser Classification Class 3B Green
10. ons With a high voltage you can suffer a dangerous electric shock when touching the wires USER MANUAL LASER SAFETY LABEL REPRODUCTIONS CAUTION CLASS 3B LASER RADIATION WHEN OPEN AVOID EXPOSURE TO BEAM LASER RADIOATION AVOID EXPOSURE TO BEAM CLASS3B LASER PRODUCT THE LASER INDICATEDS THE LASER BEAM OUTPUT APERTURE USER MANUAL The laser is working in stand alone Each time when you turn on your laser you will have this confirmed laser show 1 2 3 ee FUNC UP DOWN ENTER In the MODE OPTION setting the stand alone laser show that you are going to choose is flashing Press UP or DOWN to change stand alone laser show you will have 21 different stand alone preprogrammed laser show Their DISPLAY and EFFECT are listed below DISPALY STAND ALONE MODE LASER EFFECT AUTA Auto mixed slow laser with random show Pattern choose 01 79 MM 1 Motor speed 1 4 turn to left 5 stop 6 9 turn to right Strobe speed 00 15 Sound activated DMX control effect Master Slave control effect 12 USER MANUAL CONTROL amp FUNCTION Regular breaks during operation are essential to maximize the life of this device as it is not designed for continual use Do not switch the unit on and off in short time intervals Always unplug the unit when it is not used for a longer time Or before replacing the bulb or start servicing In the event of serious operation pr
11. s free from unwanted persons during servicing Switch off the fixture unplug the mains cable and wait until the unit has been cooled down Housings fixations and installations spots ceiling truss suspensions should be totally free from any deformation The mains cables must be in impeccable condition and should be replaced immediately when even a small problem is detected In order to protect the fixture from overheat the cooling fans if any and ventilation openings should be cleaned monthly The cleaning of aperture glass and scanner mirrors must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty 14 USER MANUAL MASTER SLAVE MODE Press FUNC to enter MODE OPTION Till to LED panel shows SLAV Press ENTER to confirm the setting The laser is working in SLAVE MODE Connect MASTER laser and SLAVE lasers with DMX cable the SLAVE lasers do what exactly MASTER laser does Check 5 2 DMX connection to have more details about laser connection DMX MODE Press FUNC to enter MODE OPTION Till to LED panel shows D001 Press ENTER to confirm the setting The laser is working in DMX MODE With help of UP DOWN button it could be easily change the DMX address of the laser 1 2 3 se FUNC UP DOWN ENTER DMX CHANNEL 000 049 BLACKOUT CH1 050 099
Download Pdf Manuals
Related Search