QB-RL78F14 In-Circuit Emulator User`s Manual
Contents
1. Since the contact is poor if tightening is too great once you have lightly fastened the MA screws tighten them again 5 Depending on the use environment when starting up a device that has been left for a long time starting it may be difficult In this case loosen the screws slightly and then retighten them 6 If startup still is difficult after 5 above check 1 to 3 again 7 Tightening the screws of the MA too much may give rise to cracks in the molded part of the MA plastic part and bend the mold into a bowed shape making contact poor 8 After soldering the NQ do not perform cleaning by flux immersion or vapor R20UT2058EJ0300 Rev 3 00 IRTE Oct 31 2013 RENESAS QB RL78F14 In Circuit Emulator CHAPTER 2 SETUP PROCEDURE 2 5 Connecting QB RL78F14 to Target System If connecting the emulation probe QB 80 EP 01T QB 144 EP 02S connect it to the QB RL78F14 and the target system by the following procedure a Connect the QB RL78F14 to the probe Connect the emulation probe to the QB RL78F14 as shown below Insert CN1 and CN2 of the probe into TCN1 and TCN3 of the QB RL78F14 In case of using QB 144 EP 02S use probe holder Figure 2 7 Connect the QB RL78F14 to the probe Probe holder QB 80 EP 01T QB 144 EP 02S b Connection of emulation probe GND wire There are three GND wires in the emulation probe Connect them to the QB RL78F 14 and target system lt 1 gt Fasten the GND wire on the QB RL782. 1 5 System Configuration for Each Target Device CHAPTER 1 The following table lists the system configuration for each target device of the QB RL78F 14 The adapter and connector for each device and common probe and adapter are sold separately An exchange GENERAL adapter a YQ connector a target connector and an emulation probe are included depending on the order product name Remark http www renesas com iecube rl78 For details refer to 1 6 Package Contents Table 1 3 Adapters and Connectors for Each Target Device Exchange Adaptor QB 20SP EA 05T Space Adaptor YQ Connector QB 20SP NQ 01T For the package drawings of the connector adapter and probe refer to the following URL Target Connector Mount Adaptor QB 30SP EA 04T QB 30SP YS 01T QB 30SP YQ 01T QB 30SP NQ 01T QB 30SP HQ 01T QB 32NA EA 05S QB 32NA TC 01S RL78 F13 QB 48FB EA 05T QB 48FB YS 01T QB 48FB YQ 01T QB 48FB NQ 01T QB 48FB HQ 01T QB 48NA EA 03S QB 48NA TC 01S QB 64FB EA 04T QB 64FB YS 01T QB 64FB YQ 01T QB 64FB NQ 01T QB 64FB HQ 01T QB 80FB EA 04T QB 30SP EA 04T QB 80FB YS 01T QB 30SP YS 01T QB 80FB YQ 01T QB 30SP YQ 01T QB 80FB NQ 01T QB 30SP NQ 01T QB 80FB HQ 01T QB 30SP HQ 01T QB 32NA EA 05S QB 32NA TC 01S RL78 F14 48NA QB 48FB EA 05T QB 48NA EA 03S QB 48FB YS 01T QB 48FB YQ 01T QB 48FB NQ 01T QB 48NA TC 01S QB 48FB HQ
3. 2 10 Figure 2 10 Connector Positions Power supply connector Connect AC adapter USB connector Connect USB interface 2 8 Switching Power On and Off Be sure to switch the power on and off according to the following procedures Switching power on Switching power off lt 1 gt QB RL78F14 power on lt 1 gt Debugger termination Note lt 2 gt Target system power on lt 2 gt Target system power off lt 3 gt Debugger startup lt 3 gt QB RL78F 14 power off Note In the procedures lt 2 gt is unnecessary if the target system is not connected Caution If the wrong sequence was used for the operation the target system or QB RL78F 14 may fail R20UT2058EJ0300 Rev300 denioenae Pag 32 of Oct 31 2013 RENESAS QB RL78F14 In Circuit Emulator CHAPTER 3 SETTINGS AT PRODUCT SHIPMENT CHAPTER 3 SETTINGS AT PRODUCT SHIPMENT Table 3 1 Settings at Shipment Not mounted Oscillator can be mountedN Power switch Set to OFF at shipment Note The oscillation circuit using an oscillation cannot be used R20UT2058EJO300 Rev 3 00 TT Oct 31 2013 RENESAS QB RL78F14 In Circuit Emulator CHAPTER 4 CAUTIONS CHAPTER 4 CAUTIONS 4 1 Cautions Regarding Differences Between Target Device and Emulator When debugging is performed by connecting the QB RL78F14 to the target system the QB RL78F14 emulates the target device as if it operates in the target system However the target device and the QB RL78F 14 operate differ
4. QB 30SP NQ 01T Products supplied with QB RL78F14 S32NA 1to8 9 Emulation probe QB 80 EP 01T 10 Exchange adapter QB 32NA EA 05S 11 Target connector QB 32NA TC 01S Products supplied with QB RL78F14 T48FB 1to8 9 Emulation probe QB 80 EP 01T 10 Exchange adapter QB 48FB EA 05T 11 YQ connector QB 48FB YQ 01T 12 Target connector QB 48FB NQ 01T Products supplied with QB RL78F14 S48NA 1to8 9 Emulation probe QB 80 EP 01T 10 Exchange adapter QB 48NA EA 03S 11 Target connector QB 48NA TC 01S RENESAS CHAPTER 1 GENERAL Page 15 of 41 QB RL78F14 In Circuit Emulator Products supplied with QB RL78F14 T64FB 1to8 9 10 11 12 Emulation probe QB 80 EP 01T Exchange adapter QB 64FB EA 04T YQ connector QB 64FB YQ 01T Target connector QB 64FB NQ 01T Products supplied with QB RL78F14 T80FB 1to8 9 10 11 12 Emulation probe QB 80 EP 01T Exchange adapter QB 80FB EA 04T YQ connector QB 80FB YQ 01T Target connector QB 80FB NQ 01T Products supplied with QB RL78F14 T100FB 1to8 9 10 11 12 R20UT2058EJ0300 Rev 3 00 Oct 31 2013 Emulation probe QB 144 EP 02S Exchange adapter QB 100FB EA 02T YQ connector QB 100FB YQ 01T Target connector QB 100FB NQ 01T RENESAS CHAPTER 1 GENERAL Page 16 of 41 QB RL78F14 In Circuit Emulator CHAPTER 1 GENERAL 1 7 AC Adapter for IECUBE The specifications of the AC adapter for IECUBE differ depending on the region of use Be sure to use an
5. QB RL78F14 In Circuit Emulator CHAPTER 4 CAUTIONS Change the positive reference voltage on the A D converter When change the positive reference voltage after setting ADREFP1 and ADREFPO stabilization wait time of emulator is different from that of the target device Table 4 1 Target devices and stabilization wait time of QB RL78F14 ADM2 register value after change stabilization wait time ADREFP1 ADREFPO Target devices QB RL78F14 1 0 1us 400us 0 0 No 400us 0 1 No 400us P122 input characteristics The P122 input characteristics differ between the target device and the emulator Table 4 2 Input Characteristics of P122 Pins Item Input Characteristics of P122 Pins Target device VIH MIN 0 8VDD VIL MAX 0 2VDD QB RL78F 14 VIH MIN 0 7VDD 2 7V lt VDD lt 5 5V VIL MAX 0 3V 2 7V lt VDD lt 5 5V Power on reset POR voltage value The power on reset POR voltage value differs from that of the target device Table 4 3 Power on reset POR voltage value Item MIN TYP MAX Target device POR 1 48 V 1 51 V 1 54 V QB RL78F14 R20UT2058EJ0300 Rev 3 00 Page 35 of 41 Oct 31 2013 RENESAS age 35 o QB RL78F14 In Circuit Emulator CHAPTER 4 CAUTIONS TTL input buffer characteristics If the port input mode register PIM is used to set the input of a pin that can be set for the TTL buffer to the TTL level the high level input voltage
6. characteristics differ between the target device and emulator See Table 4 4 for details The following pins can be set for the TTL buffer Table 4 4 Input Characteristics of TTL Conditions 2 2V 4 0 V lt VDD lt 5 5 V 2 7 V lt VDD lt 2 7 V 4 0 V lt VDD lt 5 5 V 2 7 V lt VDD lt 4 0 V 2 0V 2 7 V lt VDD lt 5 5 V 0 8V 2 7 V lt VDD lt 5 5 V Item Target device VIH MIN QB RL78F14 VIH MIN VIL MAX The detection voltage value of the voltage detector LVD The value of the detection voltage differs from that of target device Table 4 5 The detection voltage Target device QB RL78F14 Rising edge Failing edge Rising edge Failing edge 2 81V 2 75V 2 76V 3 02V 2 96V 2 97V 3 22V 3 15V 3 14V 4 42V 4 32V 4 29V 4 62V 4 52V 4 50V 4 74V 4 64V 4 60V I O port output signal level detection function I O port output signal level detection function emulation is not supported Even if you set as Output data is read PMSO 1 at port mode select register PMS the value of the port register Pmn is read Remark m 0 to 8 10 to 12 14 15 n 0to 7 Oscillation stopped detection function No supported IECUBE cannot stop operation clock RAM ECC function No supported R20UT2058EJ0300 Rev 3 00 Page 36 of 41 Oct 31 2013 RENESAS age 36 o QB RL78F14 In Circuit Emulator CHAPTER 4 CAUTIONS 4 2 Note of Debugging Opera
7. connector it will cause conductivity problems Clear out the debris with a brush c Precautions when using the CA When using the CA while minor signal propagation delay and capacitance occurs by inserting each adapter Connect the CA to the target system and fully evaluate it before use 2 CA The CA is an optional product for IECUBE and can be used to measure the waveform between IECUBE and the target system Since the pins on the CA do not correspond to the pin layout in each device the pin header cover must be mounted according to the device to be used For mounting methods of the pin header cover refer to URL http japan renesas com qb 144 ca 01 R20UT2058EJ0300 Rev 3 00 ETT Oct 31 2013 RENESAS QB RL78F14 In Circuit Emulator CHAPTER 2 SETUP PROCEDURE 2 4 Mounting and Connecting Connectors When Using T Type This section describes the methods of connecting the QB RL78F14 and target system Make connections with both the QB RL78F14 and target system powered OFF The following abbreviations are used in this section NQ Target connector YQ YQ connector EA Exchange adapter MA Mount adapter CA Check pin adapter SA Space adapter 2 4 1 Mounting NQ to target system 1 Thinly apply a two component epoxy adhesive hardening time at least 30 minutes to the ends of the four projections on the base of the NQ and adhere the NQ to the user board clean the surface of the target system board usin
8. that may pose a direct threat to human life or bodily injury artificial life support devices or systems surgical implantations etc or may cause serious property damages nuclear reactor control systems military equipment etc You must check the quality grade of each Renesas Electronics product before using it in a particular application You may not use any Renesas Electronics product for any application for which it is not intended Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for which the product is not intended by Renesas Electronics You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics especially with respect to the maximum rating operating supply voltage range movement power voltage range heat radiation characteristics installation and other product characteristics Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges Although Renesas Electronics endeavors to improve the quality and reliability of its products semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions Further Renesas Electronics products are not subject to radiation resistance design Ple
9. 01T 64FB QB 64FB EA 04T QB 64FB YS 01T QB 64FB YQ 01T QB 64FB NQ 01T QB 64FB HQ 01T 80FB QB 80FB EA 04T QB 80FB YS 01T QB 80FB YQ 01T QB 80FB NQ 01T QB 80FB HQ 01T 100FB QB 100FB EA 02T QB 100FB YS 01T QB 100FB YQ 01T Table 1 4 Common Probe and Adapter Check pin adapter QB 144 CA 01 RL78 F13 RL78 F14 QB 80 EP 01T Under 80pin of RL78 F14 RL78 F13 QB 100FB NQ 01T QB 100FB HQ 01T QB 144 EP 02S Over 100pin of RL78 F14 Emulation probe R20UT2058EJ0300 Rev 3 00 Oct 31 2013 RENESAS Page 14 of 41 QB RL78F14 In Circuit Emulator 1 6 Package Contents The included products are described for each order product name Products supplied with QB RL78F14 ZZZ R20UT2058EJ0300 Rev 3 00 Oct 31 2013 QB RL78F 14 USB interface cable 2 meters Online user registration card warranty card and software contract in one Probe holder For QB 144 EP 02S Packing list Safety Precautions IECUBE information document EMC regulation VCCI FCC document Table of Toxic and Hazardous Substance and elements oN ogfrans Products supplied with QB RL78F14 T20SP 1to8 9 Emulation probe QB 80 EP 01T 10 Exchange adapter QB 20SP EA 05T 11 Target connector QB 20SP NQ 01T Products supplied with QB RL78F14 T30SP 1to8 9 Emulation probe QB 80 EP 01T 10 Exchange adapter QB 30SP EA 04T 11 YQ connector QB 30SP YQ 01T 12 Target connector
10. AC adapter corresponding to the region of use Table 1 5 Part Numbers of AC Adapter for IECUBE Classified by Region Notes 1 Products are shipped only on order from each region 2 Contact a distributor or a Renesas Electronics representative for information on regions other than the above 3 Only the AC adapter usable in each region can be ordered R20UT2058EJO300 Rev 3 00 TT Oct 31 2013 RENESAS QB RL78F14 In Circuit Emulator CHAPTER 2 SETUP PROCEDURE CHAPTER 2 SETUP PROCEDURE This chapter explains the QB RL78F14 setup procedure Setup can be completed by performing installation setup in the order in which it appears in this chapter Perform setup along the lines of the following procedure See 1 2 Names and Functions of Hardware for clock positions Software settings 2 1 Software Settings Clock settings 2 2 See Clock Settings Mounting and connecting connectors When using the S Type see 2 3 Mounting and Connecting Connectors When Using S Type When using the T Type see 2 4 Mounting and Connecting Connectors When Using T Type Connecting QB RL78F14 to target system 2 5 See Connecting QB RL78F14 to target system Connecting USB interface cable and AC adapter 2 7 See Connecting USB interface cable and AC adapter Switching power on and off 2 8 See Switching power on and off R20UT2058EJ0300 Rev 3 00 ETT Oct 31 2013 RENESAS QB RL78F14 In Circuit Emulator CHAPTER 2 SETUP PRO
11. AS QB RL78F14 In Circuit Emulator CHAPTER 1 GENERAL 1 1 Hardware Specifications Table 1 1 QB RL78F14 Hardware Specifications Target device RL78 F13 RL78 F14 Operating voltage 2 7 to 5 5V High speed 2 7 V lt VDD lt 5 5 V 1 to 20 MHz system system clock clock notet High speed 2 7 V lt VDD lt 5 5V 1 to 32 MHz on chip oscillator clock Power Target system power supply Voltage 2 7 to 5 5 V A Current ORO 200 mA MAX weight Approx 4009 400 g Host interface USB interface 1 1 2 0 112mm Note4 7 e it p fj N if P Rear space adapter i J Front space adapter N Note1 Errors are within 0 05 However this does not apply to errors of the oscillator or clock system on the target board Note2 Errors are within 0 005 However this does not apply to errors of the oscillator or clock system on the target board Note3 When selecting 64MHz or 48MHz for timer RD 32MHz or 24MHz is supplied to the other functions including the CPU Note4 Does not include projection of power switch Note5 Includes projection of screw that fixes rear space adapter Note6 Rear space adapter can adjust the height from 30 mm longest to 0 mm shortest Note7 Front space adapter can adjust the height from 20 mm longest to 5 mm shortest R20UT2058EJ0300 Rev 3 00 RTT Oct 31 2013 RENESAS QB RL78F14 In Circuit Emulator CHAPTER 1 GENERAL 1 2 Names and Functions of Hardware Top View Bottom Vie
12. C D D E 0 lt 5 C v ENESAS QB RL78F14 In Circuit Emulator User s Manual Target Devices RL78 F13 F14 All information contained in these materials including products and product specifications represents information on the product at the time of publication and is subject to change by Renesas Electronics Corp without notice Please review the latest information published by Electronics Corp through various means including the Renesas Electronics Corp Renesas website http www renesas com Renesas Electronics Rev 3 00 Oct2013 www renesas com 10 11 12 Notice Descriptions of circuits software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples You are fully responsible for the incorporation of these circuits software and information in the design of your equipment Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits software or information Renesas Electronics has used reasonable care in preparing the information included in this document but Renesas Electronics does not warrant that such information is error free Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein Renesas Electronics does not assume
13. CEDURE 2 1 Software Settings Check the user s manual for the debugger that will be used 2 2 Clock Settings The QB RL78F14 clock must be set to the clock used by the target device For details about how to set the clock check the user s manual for the debugger that will be used QB RL78F14 clock settings for the clock used by the target device are shown below Oscillation with the resonator on the target system is not supported Therefore the in circuit emulator cannot emulate the oscillation operation of the clock on the target system Table 2 1 List of clock settings Clock Used Clock Supply 1 High speed system clock a When the clock generated within the emulator is used X1 oscillator or External input b When the clock a square wave is supplied from the target system c When the oscillator OSC1 mounted onto the emulator is used 2 Internal high speed Uses the clock internally generated from the emulator oscillation clock 3 Internal low speed Uses the clock internally generated from the emulator oscillation clock 4 Subsystem clock a When the clock generated within the emulator is used XT1 oscillator or External b When the clock a square wave is supplied from the input target system R20UT2058EJ0300 Rev 3 00 SECT Oct 31 2013 RENESAS QB RL78F14 In Circuit Emulator CHAPTER 2 SETUP PROCEDURE 1 High speed system clock The clock settings are list
14. E CREE Oct 31 2013 RENESAS QB RL78F14 In Circuit Emulator CHAPTER 1 GENERAL 1 3 System Specifications This section shows the QB RL78F14 system specifications Table 1 2 QB RL78F14 System Specifications Emulation memory capacity Internal ROM 512 KB MAX Internal RAM 61 75 KB MAX functions Ignore break points and Go Break functions Event break Execution 8 points Access 8 points Software break 2000 points Fail safe break Non map write protect SFR illegal access stack overflow or else Other Forcible break trace full break trace delay break timeout break timer overflow break Trace functions Trace data types Program address program data access address access data status time tag Unconditional trace section trace qualify trace delay trigger trace Non stop full stop full break delay trigger stop delay trigger break Memory capacity 128K frames Real time RAM monitoring function All internal RAM spaces Time measurement Measurement clock 120 MHz functions Measurement objects Start through end of program execution Start event through end event Maximum measurement time Approx 40 hours and 43 minutes Number of timers for Start through end of program execution 1 measurement Start event through end event 2 Measurement results Execution time start through end of execution Maximum minimum average total pass count between events Other Timer overflow break function timeout break function Ot
15. F 14 side of the emulation probe to the nut on the bottom of the QB RL78F 14 using a 0 or 1 Phillips precision screwdriver connection of B to A in Figure 2 8 lt 2 gt Next insert the connector on the top of the emulation probe into the connector at the opening on the bottom of the QB RL78F14 from below being careful of the insertion direction Figure 2 8 GND Wire QB RL78F 14 oL 1 dE Target system R20UT2058EJO300 Rev 3 00 ETT Oct 31 2013 RENESAS QB RL78F14 In Circuit Emulator CHAPTER 2 SETUP PROCEDURE lt 3 gt Connect the exchange adapter and emulation probe to the target connector lt 4 gt Connect the GND wires on the target system side of the emulation probe to the target system GND If a pin or screw is fastened to the target system GND remove the transparent terminal cover on the end of the GND wire and fasten the Y terminal of the GND wire to the target system C in Figure 2 8 If the GND on the target system is an exposed pad likewise fasten the Y terminal to the pad on the target system by soldering recommended soldering iron temperature setting 300 C lt 5 gt Since the length of the GND wire below the head insulated part is approximately 60 mm there must be a GND to which it can be connected to within the range of the two approximately 60 mm radius sections of the target system for connecting the emulation probe as shown in Figure 2 9 Figure 2 9 Where GND Wire Can Be Connected Target
16. Precautions for handling NQ YQ SA and CA ooooocccccciconononoconnnncncnnononcnnnnnnnnnnnnnnnnnnnnnnnnnnnn menos 28 2 4 5 Precautions for mounting IC using NQ and MA sssessesssesirsseerrsserrsstrrrssttrnsssttrnssttrnsstrrnssrenn 29 2 5 Connecting QB RL78F14 to Target SysteM oonocnnnncccnnnoncccnnnnoncccnononcnnnnnonccnnnno EN RR cnc naar nc cc AANER ERRES 30 2 6 Notes on Power Supply and GND Pin ComNectiON coooconccocccnnnccccnnnononcconnnnnnnnnonnnncnnnnnnnnnnnnnnnnnnnnnnnnnns 32 2 7 Connecting USB Interface Cable and AC AdapteT oococcinoncccnnocccccnnoncccccnnoncccnnnnnnnnnnnoncnnnnnn nc nc nnnnnnnnnnns 32 2 8 Switching Power On and OM assenaar AEE SAARE nc TANARA r canario 32 CHAPTER 3 SETTINGS AT PRODUCT SHIPMENT arahen neak AeA ERRERA EEEE E EKKA nono nn nr aA AE EEA KAA AEREE RARI 33 CHAPTER 4 CAUTION Socia E hel Ane en eae eens 34 4 1 Cautions Regarding Differences Between Target Device and Emulator oooonnnccnnnnnccnnnnnacccconnnccccnns 34 4 2 Note of Debugging ceierisrnrin li dd aer DA ee ai 37 QB RL78F14 In Circuit Emulator CHAPTER 1 GENERAL CHAPTER 1 GENERAL The QB RL78F 14 is an in circuit emulator for emulating the RL78 F13 F14 Hardware and software can be debugged efficiently in the development of systems in which the RL78 F13 F14 is used This manual descries basic setup procedures hardware specifications system specifications and how to set switches R20UT2058EJO300 Rev 3 00 SEE Oct 31 2013 RENES
17. Q YQ and SA see the NQPACK series technical materials at the website of Tokyo Eletech Corporation URL http www tetc co jp 11 CA The CA is an optional product for IECUBE and can be used to measure the waveform between IECUBE and the target system Since the pins on the CA do not correspond to the pin layout in each device the pin header cover must be mounted according to the device to be used For mounting methods of the pin header cover refer to URL http www renesas com qb 144 ca 01 R20UT2058EJ0300 Rev 3 00 SET Oct 31 2013 RENESAS QB RL78F14 In Circuit Emulator CHAPTER 2 SETUP PROCEDURE 2 4 5 Precautions for mounting IC using NQ and MA 1 Confirm that there is no weld flash in the resin sealant part of the IC If there is weld flash remove it using a knife or the like 2 Confirm that there is no weld flash breaking or bending of IC leads In particular confirm the planarity of IC leads If there is abnormality in the planarity correct that portion 3 Viewing the NQ contact pins from the top if there are foreign bodies on them remove them using a brush or the like After confirming 1 to 3 fit the IC to the NQ Also fit the MA 4 Put the supplied M2 x 6 mm screws in the four accessory holes of the MA and fasten the screws in opposite corners At that time use either the dedicated screwdriver that is supplied or a torque driver to fasten them equally in turn with a tightening torque of 0 054 Nm MAX
18. Tel 86 10 8235 1155 Fax 86 10 8235 7679 Renesas Electronics Shanghai Co Ltd Unit 204 205 AZIA Center No 1233 Lujiazui Ring Rd Pudong District Shanghai 200120 China Tel 86 21 5877 1818 Fax 86 21 6887 7858 7898 Renesas Electronics Hong Kong Limited N Unit 1601 1613 16 F Tower 2 Grand Century Place 193 Prince Edward Road West Mongkok Kowloon Hong Kong el 852 2886 9318 Fax 852 2886 9022 9044 Renesas Electronics Taiwan Co Ltd 13F No 363 Fu Shing North Road Taipei Taiwan Tel 886 2 8175 9600 Fax 886 2 8175 9670 Renesas Electronics Singapore Pte Ltd 80 Bendemeer Road Unit 06 02 Hyflux Innovation Centre Singapore 339949 Tel 65 6213 0200 Fax 65 6213 0300 Renesas Electronics Malaysia Sdn Bhd Unit 906 Block B Menara Amcorp Amcorp Trade Centre No 18 Jin Persiaran Barat 46050 Petaling Jaya Selangor Darul Ehsan Malaysia Tel 60 3 7955 9390 Fax 60 3 7955 9510 Renesas Electronics Korea Co Ltd 11F Samik Lavied or Bldg 720 2 Yeoksam Dong Kangnam Ku Seoul 135 080 Korea Tel 82 2 558 3737 Fax 82 2 558 5141 O 2013 Renesas Electronics Corporation All rights reserved Colophon 1 3 QB RL78F14 In Circuit Emulator User s Manual ENESAS Renesas Electronics Corporation R20UT2058EJ0300
19. and EA by following the procedure below 1 Check the orientation of pin 1 align the TC guide pin to the guide hole at the tip of the EA flexible printed circuit FPC and then insert it See Figure 2 5 2 Check conductivity between the TC and EA at this time 3 Solder the TC to the guide locking pad that can be seen from the FPC tip flexible guide hole using a soldering iron with a tip radius of 61 0 mm or smaller Once soldered the TC and EA cannot be removed from each other 4 Use extreme care so that the EA FPC cable does not apply stress to the TC If the EA applies even a small amount of stress to the TC we recommend securing the section soldered to the TC board with adhesive Figure 2 5 Magnified guide hole view when TC and EA are mated amp mating diagram TC When the EA and TC are mated Magnified view The guide pin can be seen when the TC and EA are mated R20UT2058EJ0300 Rev 3 00 RTT Oct 31 2013 RENESAS QB RL78F14 In Circuit Emulator CHAPTER 2 SETUP PROCEDURE 2 3 3 General Precautions when Using the EA TC 1 Causes of connector conductivity problems a When flux gets inside the connector when mounting the TC Since flux easily rises into the connector if it gets into the connector completely wash it out using a solvent such as alcohol Wash it at least five or six times If conductivity is unstable repeatedly wash it b Debris gets inside the connector If debris such as fuzz gets inside the
20. any liability for infringement of patents copyrights or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document No license express implied or otherwise is granted hereby under any patents copyrights or other intellectual property rights of Renesas Electronics or others You should not alter modify copy or otherwise misappropriate any Renesas Electronics product whether in whole or in part Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from such alteration modification copy or otherwise misappropriation of Renesas Electronics product Renesas Electronics products are classified according to the following two quality grades Standard and High Quality The recommended applications for each Renesas Electronics product depends on the product s quality grade as indicated below Standard Computers office equipment communications equipment test and measurement equipment audio and visual equipment home electronic appliances machine tools personal electronic equipment and industrial robots etc High Quality Transportation equipment automobiles trains ships etc traffic control systems anti disaster systems anti crime systems and safety equipment etc Renesas Electronics products are neither intended nor authorized for use in products or systems
21. ase be sure to implement safety measures to guard them against the possibility of physical injury and injury or damage caused by fire in the event of the failure of a Renesas Electronics product such as safety design for hardware and software including but not limited to redundancy fire control and malfunction prevention appropriate treatment for aging degradation or any other appropriate measures Because the evaluation of microcomputer software alone is very difficult please evaluate the safety of the final products or systems manufactured by you Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances including without limitation the EU RoHS Directive Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture use or sale is prohibited under any applicable domestic or foreign laws or regulations You should not use Renesas Electronics products or technology described in this document for any purpose relating to military applications or use by the military including but not li
22. demark of International Business Machines Corporation CONTENTS GHAPTER1 GENERAL orga A a Aa dea 7 1 1 Hardware SpecificatiONS ooooocninncccncnnnnnnnnnnonnoncnncnnnnnnnnonnnconnnnnnn anno nn nnnn cnn n nn anne nn nn nn rra nnnnnnnnnnncnncnnanannes 8 1 2 Names and Functions of Hardware ooononcccnnnocccccononcccnononcncnanoncncn cano ncn cnn rca r cnn rr rnn rre 9 EE A E 11 SEARS A O 12 1 5 System Configuration for Each Target Device ooononccccnnnccccnnnocccccononcccnnnoncncnnnnoncccnn arc cn canon nc cnnnnnncnannns 14 1 65 Package CONS caniae la iii EEA EER EE E EE Ai CRA ti 15 1 77 AC Adapter tor IECGUBE ovocitos gesdandedca shag das teniaeesaneiaecstea lanes aaedasee aiii 17 CHAPTER 2 SETUP PROCEDURE civic li ad NAE EEE da bb 18 2A Software Settings O 19 O e eaaa e E O 19 2 3 Mounting and Connecting Connectors When Using S Typ8 oooononcccnnnnnicinnnnocccccnnoncccnnnancccnnnnnncncnnn 23 2 3 1 Mounting TO totarget syste aaa o EEE berets EAEE 23 2 32 MAMO the TCto EA tenia cents E E EEE EE EEEE 24 2 3 3 General Precautions when Using the EA TC ooooococccccncnnconononocnnncnonnononcnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnos 25 2 4 Mounting and Connecting Connectors When Using T Typ8 oooocioncccnonoccccnnnonccccononcnnnnaancccnnnannncnnnn 26 24 1 lt Mounting NO to target system wz cnda EE E A EA EE aber 26 24 2 Mounting YING eoe e E AE E a E a alias ta 27 243 Plugging EA MO YO anir ea E A E A EE 27 24 4
23. ects exchange adapter to target connector Connector soldered to target system Adapter used for mounting target device into socket Target device QB RL78F14 In Circuit Emulator CHAPTER 1 GENERAL Remarks 1 2 R20UT2058EJ0300 Rev 3 00 Oct 31 2013 Refer to 1 6 Package Contents for the purchase forms of the above products As for handling of connectors refer to 2 3 Mounting and Connecting Connectors When Using S Type or 2 4 Mounting and Connecting Connectors When Using T Type The part number of lt 4 gt differs depending on the region of use See Table 1 5 Part Numbers of AC Adapter for IECUBE Classified by Region for the part numbers The IECUBE requires an AC adapter that must be purchased separately See Table 1 4 Common Probe and Adapter for the part numbers of lt 5 gt and lt 6 gt The combination of lt 7 gt lt 8 gt lt 9 gt lt 10 gt and lt 11 gt varies depending on the emulation device See Table 1 3 Adapters and Connectors for Each Target Device for the combinations To determine the T Type socket or the S Type socket check for T or S at the end of the socket product name Example QB 64FB EA 01T gt T Type QB 48NA EA 02S gt S Type Even with the T Type socket there may not be a space adapter YQ connector mount adapter In this case the device cannot be mounted in the socket Check Table 1 3 Adapters and Connectors for Each Target Device Target Device QB RL78F14 In Circuit Emulator
24. ed below Table 2 2 Settings for High Speed System Clock Type of Clock to Be Used a When the clock generated within the emulator is used b When the clock a square wave is supplied from the target system ote c When the oscillator OSC1 mounted onto the emulator is used Oscillator mounted Note This setting is not possible when TARGET LED is not lit Remarks 1 Settings other than the above are prohibited 2 Selection of a or b is possible regardless of whether the oscillator is not mounted in the OSC1socket a When the clock generated within the emulator is used This method uses the clock generated inside the emulator The oscillation frequency that will be used must be set in the debugger For details about how to set the oscillation frequency check the user s manual for the debugger that will be used b When the clock a square wave is supplied from the target system The clock input from the target system is then used To input a clock from the target system input to the clock pin X2 the square wave signal with the same voltage potential as that of the target device supply voltage VDD Inputting the inverted signal to X1 is not necessary The selectable frequencies are same as those of the target device For debugger settings check the user s manual for the debugger that will be used Oscillation by a resonator in the target system is not supported c When the oscillator OSC1 mounted on
25. ently in the following ways Consequently the target device should be used for final evaluation before launching mass production and the customer is to be responsible for judging the appropriateness of applying the QB RL78F 14 On chip debug function The on chip debug function cannot be emulated Oscillator The QB RL78F 14 does not support clock input by an oscillator in the target system Consequently the operation clock frequency when the target device is mounted in the target system may differ from the operation clock frequency when the QB RL78F 14 is connected Pin characteristics The pin characteristics of the QB RL78F 14 slightly differ when the target device is mounted to the target system because a connector adapter emulation probe and circuit board exist between the QB RL78F 14 and the target system In particular note that the A D converter conversion results are commonly affected Current consumption The current consumption of the QB RL78F 14 differs from that of the target device The maximum current consumption is around 200 mA In the same manner the current consumption in standby mode also differs from that of the target device A D conversion error around O V and 5 5 V A D conversion error around O V and 5 5 V on QB RL78F 14 is large Use on chip debugging or actual equipment for checking A D conversion in 0 1 V and under or 5 36 V and over R20UT2058EJ0300 Rev 3 00 SEE Oct 31 2013 RENESAS
26. er of electrical shock if the product is used as described above in 1 Circumstances not covered by product guarantee Readers Purpose Organization How to Read This Manual Conventions How to Use This Manual This manual is intended for users who wish to perform debugging using the QB RL78F14 The readers of this manual are assumed to be familiar with the device functions and usage and to have knowledge of debuggers This manual is intended to give users an understanding of the basic specifications and correct usage of the QB RL78F 14 This manual is divided into the following sections e General e Setup procedure Settings at product shipment e Cautions It is assumed that the readers of this manual have general knowledge in the fields of electrical engineering logic circuits and microcontrollers This manual describes the basic setup procedures and how to set switches To understand the overall functions and usages of the QB RL78F 14 Read this manual in the order of the CONTENTS The mark lt R gt shows major revised points The revised points can be easily searched by copying an lt R gt in the PDF file and specifying it in the Find what field To know the manipulations command functions and other software related settings of the QB RL78F 14 gt See the user s manual of the debugger supplied with the QB RL78F 14 to be used Note Footnote for item marked with Note in the text Caution Infor
27. ered or repaired by the customer If it was dropped broken or given another strong shock e Use at overvoltage use outside guaranteed temperature range storing outside guaranteed temperature range If power was turned on while connection to the AC adapter USB interface cable or target system was in an unsatisfactory state If the cable of the AC adapter the USB interface cable the emulation probe or the like was bent or pulled excessively If an AC adapter other than the supplied product was used e If the product got wet e If this product is connected to the target system when there is a potential difference between the GND of this product and GND of the target system e If the connectors or cables are plugged unplugged while this product is in the power on state e If excessive load is applied to the connectors or sockets As for handling please see 2 3 Mounting and Connecting Connectors When Using S Type or 2 4 Mounting and Connecting Connectors When Using T Type e If a metal part of the power switch cooling fan or another such part comes in contact with an electrostatic charge If the product is used or stored in an environment where an electrostatic or electrical noise is likely to occur 2 Safety precautions If used for a long time the product may become hot 50 C to 60 C Be careful of low temperature burns and other dangers due to the product becoming hot e Be careful of electrical shock There is a dang
28. g alcohol or the like If alignment of target system pads to NQ leads is difficult align them as in 2 2 Align by inserting the guide pins for alignment for the NQ NQGUIDE through the pin holes on the top of the NQ Accessory holes are 41 0 mm non through holes in two or three places For hole positions see the particular NQ drawing 3 Solder after fitting the MA to the NQ This is to prevent troubles such as flux or solder splashing and adhering to the NQ contact pins when soldering Soldering conditions Solder reflow 260 C x 10 seconds or less Manual soldering 350 C x 5 seconds or less 1 pin Caution Do not perform washing by flux immersion or vapor 4 Take away the guide pins R20UT2058EJ0300 Rev 3 00 TN Oct 31 2013 RENESAS QB RL78F14 In Circuit Emulator CHAPTER 2 SETUP PROCEDURE 2 4 2 Mounting YQ to NQ 1 After confirming that there are no broken or bent YQ contact pins fit the YQ in the NQ and fasten it using the supplied YQGUIDE for the fastening method see the next step 2 If repeatedly inserting and removing be sure to inspect the YQ pins before fitting If pins are bent correct them using something thin and flat such as the edge of a knife 2 Fasten YQ to the NQ on the target system using the supplied YQGUIDE Fasten the screws equally in the four corners using the supplied flat blade screwdriver or a torque driver The tightening torque of the YQGUIDE is 0 054 Nm MAX Too great tighte
29. h speed oscillation clock in the user program 3 Internal low speed oscillation clock This method uses the clock inside the emulator by configuring the use of the low speed oscillation clock in the user program 4 Subsystem clock The clock settings are listed below Table 2 3 Settings for Subsystem Clock Type of Clock to Be Used a When the clock generated within the emulator is used b When the clock a square wave is supplied from the target system a When the clock generated within the emulator is used This method uses the clock inside the emulator by configuring the use of the subsystem clock in the user program For debugger settings check the user s manual for the debugger that will be used b When the clock a square wave is supplied from the target system The clock input from the target system is then used To input a clock from the target system input to the clock pin XT2 the square wave signal with the same voltage potential as that of the target device supply voltage VDD Inputting the inverted signal to XT1 is not necessary The selectable frequencies are same as those of the target device For debugger settings check the user s manual for the debugger that will be used Oscillation by a resonator in the target system is not supported R20UT2058EJO300 Rev 3 00 ETT Oct 31 2013 RENESAS QB RL78F14 In Circuit Emulator CHAPTER 2 SETUP PROCEDURE 2 3 Mounting and Connecting Connect
30. her functions Command functions set in the console mapping function event function coverage function snapshot function DMM function power off emulation function pin mask function flash self programming emulation function R20UT2058EJ0300 Rev 3 00 ELT Oct 31 2013 RENESAS QB RL78F14 In Circuit Emulator CHAPTER 1 GENERAL 1 4 System Configuration This section shows the system configuration when using the QB RL78F14 connected to a PC Windows PC PC AT compatible Connection is possible even without optional products Figure 1 2 System Configuration lt 1 gt lt 2 gt P i e N lt 4 gt lt 1 gt Host machine lt 2 gt USB interface cable lt 3 gt AC adapter lt 4 gt QB RL78F14 lt 5 gt Check pin adapter optional lt 6 gt Emulation probe lt 7 gt Exchange adapter lt 8 gt Space adapter optional lt 9 gt YQ connector lt 10 gt Target connector lt 11 gt Mount adapter optional lt 12 gt Device lt 13 gt Target system R20UT2058EJ0300 Rev 3 00 Oct 31 2013 ne lt 10 gt lt 13 gt asi lt 13 gt S type Windows PC IBM PC AT compatible can be used Cable connecting QB RL78F 14 to host machine AC adapters classified by region This product Adapter used for monitoring waveforms with oscilloscope High characteristic FPC type emulation probe Adapter that performs pin conversion Adapter used for height adjustment Connector that conn
31. mation requiring particular attention Remark Supplementary information Numeric representation Binary xxxx or xxxxB Decimal xxxx Hexadecimal xxxxH Prefix indicating power of 2 address space memory capacity K kilo 2 1 024 M mega 2 1 024 Terminology The meanings of the terms used in this manual are described in the table below Term Meaning Target device This is the device to be emulated Target system This is the system to be debugged This includes the target program and the hardware provided by the user IECUBE Generic name for Renesas Electronics high performance compact in circuit emulator Related Documents Please use the following documents in conjunction with this manual The related documents listed below may include preliminary versions However preliminary versions are not marked as such Documents Related to Development Tools User s Manuals Document Name Document Number QB RL78F 14 In Circuit Emulator This manual RL78 family User s Manual Software RO1US0015E Caution The related documents listed above are subject to change without notice Be sure to use the latest version of each document for designing etc IECUBE is a registered trademark of Renesas Electronics Corporation in Japan and Germany Windows is either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries PC AT is a tra
32. may cause poor contact Moreover a board being connected to the YQ must have accessory holes in prescribed positions four places 2 3 mm or 3 3 mm The 3 8 mm or 04 3 mm that is the screw head size is an area where wiring is prohibited 4 In YQ and SA removal since there is a danger of YQ pins being bent or broken when prying and wiggling remove them gradually using a flatbladed screwdriver from four directions Moreover to connect and use the YQ and SA screw the YQ to the NQ according to the YQGUIDE included with the YQ using a 2 3 mm flatbladed screwdriver and then connect it to the SA Fix the torque at 0 054 Nm MAX If even one place is overtightened it may cause poor contact 5 For the NQ YQ and SA since there is a danger that washing fluid on the structure will remain in the connector do not perform washing 6 NQ IC and YQ cannot be used in combination 7 ANQ YQ system cannot be used in an environment of vibrations or shocks 8 It is assumed that this product will be used in system development and evaluation Moreover when used in Japan Electrical Appliance and Material Control Law and electromagnetic disturbance countermeasures have not been applied 9 Since there are rare cases of shape change if the box is left for a long time in a place where it is 50 C or higher for safekeeping store it in a place where it is no higher than 40 C and direct sunlight does not hit it 10 For details about handling the N
33. mited to the development of weapons of mass destruction When exporting the Renesas Electronics products or technology described in this document you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations It is the responsibility of the buyer or distributor of Renesas Electronics products who distributes disposes of or otherwise places the product with a third party to notify such third party in advance of the contents and conditions set forth in this document Renesas Electronics assumes no responsibility for any losses incurred by you or third parties as a result of unauthorized use of Renesas Electronics products This document may not be reproduced or duplicated in any form in whole or in part without prior written consent of Renesas Electronics Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products or if you have any other inquiries Note 1 Renesas Electronics as used in this document means Renesas Electronics Corporation and also includes its majority owned subsidiaries Note 2 Renesas Electronics product s means any product developed or manufactured by or for Renesas Electronics 2012 4 General Precautions for Handling This Product 1 Circumstances not covered by product guarantee e If the product was disassembled alt
34. ning causes bad connections However four screws for fitting to the NQ M2 x 10 mm 4 units are included with the YQ Figure 2 6 Mounting of EA YQ and NQ EZ YQGUIDE supplied with YQ A CSTV Target system 2 4 3 Plugging EA into YQ Match the pin 1 position of the YQ or SA corner cuts match in both to the pin 1 position of the EA and plug in When plugging or unplugging press on the NQ YQ and SA with a finger so that there is no force on the NQ When plugging or unplugging be careful of the direction of wiggling As a tool when unplugging insert some kind of thin non conductive material such as a wooden stick between the YQ SA and EA and wiggle while slowly unplugging Be careful since the connector will be damaged if this is done in the wrong direction R20UT2058EJ0300 Rev 3 00 TT Oct 31 2013 RENESAS QB RL78F14 In Circuit Emulator CHAPTER 2 SETUP PROCEDURE 2 4 4 Precautions for handling NQ YQ SA and CA 1 When taking the NQ from the box press down on the body and take out the sponge first 2 Since the pins of the YQ are thin and easily bent be careful When inserting it in the NQ confirm that there are no bent pins 3 When screwing a YQ soldered to a board to the NQ fasten the screws in four places in turn using a 0 or 1 Phillips precision screwdriver or torque driver after tentatively tightening them Fix the torque at 0 054 Nm MAX If just one place is overtightened it
35. ors When Using S Type This section describes the methods of connecting the QB RL78F14 and target system Make connections with both the QB RL78F 14 and target system powered OFF The following abbreviations are used in this section TC Target connector EA Exchange adapter CA Check pin adapter 2 3 1 Mounting TC to target system 1 Apply cream solder to the foot pattern of the target system for mounting an IC 2 There is a circular protrusion Figure2 4 in middle of the bottom of the TC The center of this cylinder is a metallic component metal plated for the GND connection In the same manner as the IC pad the TC GND is connected to the target board GND by applying cream solder to the pad in the center of the recommended IC foot pattern and then reflow soldering Figure 2 4 TC protrusion 3 Soldering condition of TC a Reflow soldering At 235 C for amaximum of 10 seconds main heating insulator metal Be sure b Manual soldering At 320 C for a maximum of 5 seconds per pin 4 Precautions on flux splatter If the solder flux splatters when the connector is soldered faulty contact may occur to cover the upper part of the connector with aluminum foil Do not clean the connector because the flux solvent may remain inside the connector R20UT2058EJO300 Rev 3 00 ETA Oct 31 2013 RENESAS QB RL78F14 In Circuit Emulator CHAPTER 2 SETUP PROCEDURE 2 3 2 Mating theTC to EA Mate the TC
36. pters and Connectors for Each Target Device Addition of A D conversion error around O V and 5 5 V to Chapter 4 Cautions October 31 2013 Addition of the followings to 1 6 Package Contents Safety Precautions IECUBE information document EMC regulation VCCI FCC document Table of Toxic and Hazardous Substance and elements Change of connection procedure of AC adapter and QB RL78F14 in 2 7 Connecting USB Interface Cable and AC Adapter QB RL78F14 In Circuit Emulator User s Manual Publication Date October 31 2013 Rev 3 00 Published by Renesas Electronics Corporation ENESAS SALES OFFICES Renesas Electronics Corporation http www renesas com Refer to http www renesas com for the latest and detailed information Renesas Electronics America Inc 2880 Scott Boulevard Santa Clara CA 95050 2554 U S A Tel 1 408 588 6000 Fax 1 408 588 6130 Renesas Electronics Canada Limited 1101 Nicholson Road Newmarket Ontario L3Y 9C3 Canada Tel 1 905 898 5441 Fax 1 905 898 3220 Renesas Electronics Europe Limited Dukes Meadow Millboard Road Bourne End Buckinghamshire SL8 5FH U K Tel 44 1628 651 700 Fax 44 1628 651 804 Renesas Electronics Europe GmbH Arcadiastrasse 10 40472 Dusseldorf Germany Tel 49 211 65030 Fax 49 211 6503 1327 Renesas Electronics China Co Ltd 7th Floor Quantum Plaza No 27 ZhiChunLu Haidian District Beijing 100083 P R China
37. system c Ensuring isolation Adjust the height of the QB RL78F14 with the front space adapter and the rear space adapter and ensure isolation from the target system d Precautions related to emulation probe lt 1 gt Be careful that stress of the emulation probe is not placed on the target connector Moreover when removing the emulation probe remove it slowly while pressing down on the exchange adapter with a finger so that there is no stress on the target connector lt 2 gt Be sure to connect the GND wire of the emulation probe to the QB RL78F14 and the target system If it cannot be connected the impedance of the cable is unstable and could bring about lowering of signal transmission characteristics or distortion of the output waveform for an input waveform R20UT2058EJ0300 Rev 3 00 REET Oct 31 2013 RENESAS QB RL78F14 In Circuit Emulator CHAPTER 2 SETUP PROCEDURE 2 6 Notes on Power Supply and GND Pin Connection For power supplies and GND pins of the target device be sure to connect all pins to each power supply or GND 2 7 Connecting USB Interface Cable and AC Adapter Plug the USB interface cable supplied with the QB RL78F14 into the USB connector of the host machine and plug the other side into the USB connector on the rear of the QB RL78F14 Plug the AC adapter into the power supply connector on the rear of the QB RL78F14 and plug the other side into a receptacle For QB RL78F 14 connector positions see Figure
38. tion after target system power application After power application a program will be executed for the target device mounted in the target system when reset is released However with the QB RL78F14 the program does not start until an operation to start execution is performed after the program is downloaded using the debugger Relation between Standby function and Break function The break is interrupt function of CPU The standby mode is released by the break for using the following debug function Stops execution of the user program Step execution of the standby instruction Stops user program after execution instruction Pseudo real time RAM monitor function Break When Readout Pseudo Dynamic Memory Modification Break When Write Breakpoint setting executing of the user program Invalid memory access detection function IAW The behavior when detecting an invalid memory access is different between target device and emulator Target device Reset QB RL78F14 Fail safe break CRC calculation function When using the CRC calculation function do not set software breaks Differing calculation results will be output R20UT2058EJ0300 Rev 3 00 Page 37 of 41 Oct 31 2013 7tENESAS age 37 o REVISION HISTORY QB RL78F14 In Circuit Emulator User s Manual Description Summary August 10 2012 First Edition issued August 22 2013 Change of document format Addition of QB 32NA TC 01S and QB 48NA TC 01S to Table 1 3 Ada
39. to the emulator is used Mount an oscillator in the OSC1 socket in the emulator and then select the Clock socket in the debugger The clock generated from the oscillator mounted on the emulator is used The selectable frequencies are same as those of the target device To modify the clock setting the acrylic board on the bottom of the QB RL78F14 must be removed The acrylic board can be removed by lifting it up For debugger settings check the user s manual for the debugger that will be used R20UT2058EJ0300 Rev 3 00 SRT ET Oct 31 2013 RENESAS QB RL78F14 In Circuit Emulator CHAPTER 2 SETUP PROCEDURE Figure 2 1 Acrylic Board Removal Method As an oscillator to be mounted in the OSC1 socket in the emulator use the one that satisfies the following specifications Supply voltage 5 0 V Output level CMOS Note An oscillation circuit that uses a resonator cannot be used Figure 2 2 Oscillator Shape NC Y Vcc NC p Vec GND CLOCK OUT GND CLOCK OUT Top View Figure 2 3 Mapping of Oscillator to Socket Oscillator y Socket 7 Oscillator _OSC1 Pin Number 4 11 aocor e 5 10 6 9 Remark Insert the oscillator into the socket take care for the pin 1 position R20UT2058EJ0300 Rev 3 00 ETT Oct 31 2013 RENESAS QB RL78F14 In Circuit Emulator CHAPTER 2 SETUP PROCEDURE 2 Internal high speed oscillation clock This method uses the clock inside the emulator by configuring the use of the hig
40. w Vasa aseo omo CEEGGANAIERERD TONI TCN2 TCN3 TCN4 CN6 OSC1 POWER TARGET Red LED Green LED r Side View Power switch Power supply connector Cooling fan USB connector Figure 1 1 Names of Parts of QB RL78F14 R20UT2058EJ0300 Rev 3 00 EEE Oct 31 2013 RENESAS QB RL78F14 In Circuit Emulator CHAPTER 1 GENERAL 1 TCN1 TCN2 TCN3 These are connectors for connecting a check pin adapter or emulation probe 2 OSC1 This is a socket for mounting the oscillator 3 CN6 TCN4 This is a connector for the shipment inspection It is not something that the user will need 4 POWER Red LED This is an LED that shows whether the power supply of the QB RL78F 14 is switched on LED State QB RL78F 14 State Put Power switch ON Not lit Power switch OFF or AC adapter not connected to QB RL78F 14 Blinking Internal error occurred Contact an Renesas Electronics sales representative or distributor 5 TARGET Green LED This is an LED that shows whether the power supply of the target system is switched on LED State Target System State Put Target system power supply ON Not lit Target system power supply OFF or target system not connected 6 Power switch This is the power switch of the QB RL78F 14 It is OFF at shipment 7 Cooling fun This is the cooling fun of the QB RL78F14 It works when the power supply of the QB RL78F 14 is switched on R20UT2058EJ0300 Rev 3 00 SS
Download Pdf Manuals
Related Search