IXP220 Software Manu..
Contents
1. Address 192 1 3 2 Subnet Mask 255 255 252 0 Subnet Host bits Device Name DP220 Product Name DP220 Device Discovery Version 01 00 Force Update Figure 3 Configuration Settings Dialog 4 Assign the IXP220 Controller to EITHER a local or non local Subnet as follows ewww impro net o ISW302 0 0 GB 00 March 2009 Page 10 Local Subnet refers to the subnet connecting the Controller and the PC whether running IXP220 or the stand alone Ethernet Discovery Utility By assigning an invalid IP Address the IXP220 may no longer communicate Refer to the Controller s Installation Manual for information on restoring factory defaults Case 1 using the integrated Ethernet Discovery Utility access the Ethernet Discovery Utility direct from the IXP220 Base Application see the Tip 1 on page 8 After detection and configuration it s not necessary to assign a Logical Address as the IXP220 Auto ID process does this Therefore it is not necessary to export the settings to a file i 2 3 4 5 In the Device IP Address textbox enter a Device IP Address Tick the checkbox to set the IP Address to Static In the Gateway IP Address textbox enter a Gateway IP Address Tick the checkbox to set the Gateway IP Address to Static Continue with ONE of the procedures Subnet Mask or Subnet Host Bits below Subnet Mask 1 Select the Subnet Mask radio button 2 Inthe textbox alongside enter the Subnet Mask 3 Ti2. the Select Destination Location dialog select the Destination Directory we recommend that you use the default location of C Program Files Firebird Firebird 2 1 Click the Next button From the drop down menu select the Full Installation of Super Server and Development Tools option At the Select Start Menu Folder screen click Next ewww impro net o ISW302 0 0 GB 00 March 2009 Page 4 j5 Setup Firebird Co o fea Select Additional Tasks Which additional tasks should be performed ED Select the additional tasks you would like Setup to perform while installing Firebird then click Next J Use the Guardian to control the server Run Firebird server as Run as an Application Run as a Service V Start Firebird automatically everytime you boot up v Install Control Panel Applet V Copy Firebird client library to lt system gt directory V Generate client library as GDS32 DLL for legacy app support lt Back Net gt Cancel Figure 2 Firebird Select Additional Tasks 10 On the Select Additional Tasks screen Select the Use the Guardian to Control the Server option Select the Run as a Service option Select the Start Firebird Automatically Everytime You Boot Up option Select the Install Control Panel Applet option Select the Copy Firebird Client Library to lt System gt Directory option Select the Generate Client Library as GDS32 DLL for Legacy ap
3. ault username is SYSDBA and the default password is masterkey 3 From the Security Device Search drop down list make your selection from the following choices Automatically Search for IXP220 3 and IXP220 4 installations where an ImproX RS is connected but you are unsure of the COM Port number in use by the ImproX RS Enter the COM Port Name for IXP220 3 and IXP220 4 installations where an ImproX RS is connected and you know the COM Port number in use by the ImproX RS Recommended when you have an enabled Bluetooth or Infrared Port Automatically searching on a computer that has an enabled Bluetooth or Infrared Port may result in the IXP220 ewww impro net o ISW302 0 0 GB 00 March 2009 Page 14 application freezing If you select this choice enter the COM Port number in the supplied textbox do NOT Have One for XP220 1 and XP220 2 installations with no ImproX RS On first time installation of the IXP220 Software the do NOT Have One choice is by default selected In this case if the site has an ImproX RS connected that s unlocked for a System 3 or System 4 then the IXP220 Software starts up as a System 1 This means no search is performed for the ImproX RS 4 Click the amp button Database Version Check After completing the login action the Automatic Database Upgrade Utility checks the database version If the Utility confirms the Database is older than that needed by the Software a Warning dialog t
4. ck the checkbox to set the Subnet Mask to Static Subnet Host Bits 1 Select the Subnet Host Bits radio button 2 Enter the number of bits in the textbox If necessary amend the supplied Device Name Use the same site prefix to name devices belonging to the same site Example Site 1 Factory Site 1 Testing ewww impro net o ISW302 0 0 GB 00 March 2009 Page 11 7 Ensure the Force Update checkbox is UNCHECKED when assigning an Address on the Local Subnet Alternatively ensure the Force Update checkbox is CHECKED when assigning an Address on an external subnet si Ifthe Force Update checkbox remains UNCHECKED the Controller changes the IP Address testing communication on the new Address If successful the update is final if not the Controller reverts to its old settings By CHECKING the Force Update checkbox the Controller changes the IP Address and reboots In this case if the Address points outside the Local Subnet the Controller is not found until it s physically moved to the new location Changes to the IP Configuration result in the Controller rebooting on acceptance of the change The Configuration Settings dialog remains open while allowing the Controller to reboot On closure of the dialog the Utility again searches for the Controller and if successful displays the updated Controller details 8 Click the Update buiton After installing the Controller in its new location you can
5. ctory file path ensure that you enter text only NO spaces wm IXP220 V1 80 Build 16 Beta Software olo es Choose Install Set 6 Introduction Install Set Full License Agreement J DP220 Base Application A Choose Install Folder A Choose Install Set Figure 1 Install Set Menu ewww impro net o ISW302 0 0 GB 00 March 2009 Page 2 9 At the Choose Install Set screen from the Install Set drop down list make your preferred installation type selection 44 An Install Set is a collection of pre selected applications suitable for specific scenarios Customize an Install Set option by selecting or de selecting applications from the list 10 Click the Next button 11 Click the Install button 12 At the Install Complete dialog click the Done button LJ By default Windows XP SP2 and SP3 installs a firewall To keep this Firewall unblock the TCP Ports thereby allowing functionality of the IXP220 Software Continue as follows 10 11 12 ISW302 0 0 GB 00 Select Start gt Control Panel Select the Windows Firewall icon In the Windows Firewall Settings dialog select the Exceptions tab Click on the Add Port bution Unblock the TCP Port in the Add a Port dialog by completing the Name for example Impro and Port Number Ethernet Controllers use 10005 text boxes Select the TCP radio button Close the Add a Port dialog by clicking the OK button At the Windows Firewall Settings dial
6. different operations in the IXP220 Base Application These menus include File Hardware Configuration Tagholder Web and Help Topics B Page Tabs Switches between the different configuration settings for example e Site Configuration e Controller Configuration e Door Configuration e Access Group Configuration e Tagholder Configuration e Holiday Configuration C Configuration Pane Lets you adjust various settings based on your selection from the Page Tabs or Menu Bar D Viewer Pane h Click the KY button placed alongside the Page Tabs to adjust the Base Applications layout e First Click closes the Viewer Pane opening the Configuration Pane in Full Screen Mode e Second Click opens the Viewer Pane in Full Screen Mode e Third Click returns the Base Application to Split screen Mode showing both the Configuration Pane and the Viewer Pane ewww impro net o ISW302 0 0 GB 00 March 2009 Page 20 The Viewer Pane consists of Tabs showing the following information e Transaction Viewer dgives a live real time view of all types of transactions in the System It displays the names of the Doors Locations and details of Tagholders who have entered or exited these Doors Locations e Alarm Transaction Viewer gives a live real time view of all alarm transactions in the System It displays the names of the Doors Locations and details of Tagholders who have entered or exited these Doors Locations e Co
7. ells you an upgrade is needed Perform the upgrade as follows 1 Atthe Warning dialog click the OK button 2 Inthe Database Updater dialog click the Upgrade button 3 At the Message dialog click the OK button If you do not upgrade the Database immediately the IXP220 Software closes Hardware Auto ID During an Auto ID the Base Application polls attached Controllers and Terminals identifying their type and their Logical Address After physically connecting and powering up the ImproX Hardware carry out the Auto ID process Hardware detected for the first time receives a Logical Address This Logical Address does not change thus ensuring continuity in the Database ewww impro net o ISW302 0 0 GB 00 March 2009 Page 15 1 Atthe Auto ID is Recommended for New Sites dialog click the Yes button 2 Atthe Confirm Auto ID dialog click the OK button 3 If you connected your Controller to the Host PC via an ImproX RS from the Auto ID Communications Configuration dialog select the appropriate Com Port record 4 If you connected your Controller to the Host PC via TCP IP click the lal button 5 Inthe Channel column replace the default IP Address details with the IP Address of your Controller 6 Press Enter Alternatively If your Controller does not appear in the Auto ID Communications Configuration dialog continue as follows 1 Click the button 2 Inthe Input dialog enter the Subnet Mask details for your Net
8. find it using the Network gt Search IP menu option Case 2 using the stand alone Ethernet Discovery Utility use this version of the Ethernet Discovery Utility when installing a Controller at a remote location without prior configuration on the local subnet of the Host PC Install the Utility on a PC on the Remote Subnet to detect and configure the Controller Do NOT check the Force Update checkbox Export the settings to a file for manual entry into the IXP220 Base Application ewww impro net o ISW302 0 0 GB 00 March 2009 Page 12 Change the Default Password 1 On the Menu Bar go to Configuration gt Change Password 2 Logon if requested see page 9 3 Inthe Enter New Device Password dialog in the Enter New Password textbox enter a new password not exceeding 16 characters for the selected Controller 4 Inthe Confirm New Password textbox re enter your password 5 Click on the button ewww impro net o ISW302 0 0 GB 00 March 2009 Page 13 que Configuration Procedure Open the Software Logon Username Password Server Name localhost Database C IXP220 Database DB220 FDB w fuu Security Device Search Automatically Search v Automatically searching for a security device on a PC with an enabled Bluetooth or infrared port may cause the Application to hang ka ks Figure 4 Login Dialog 1 In Windows click Start gt All Programs gt IXP220 gt IXP220 2 Enter your Username and Password The def
9. gholder may not pass this same exit access point within the specified time period 4 Enable or disable Controllers as per your requirements by selecting or de selecting the Controller Enabled checkbox 5 Click the E button ewww impro net o ISW302 0 0 GB 00 March 2009 Page 18 Using the IXP220 Software 4 IXP220 User Interface e LJ vx 220 New Ste File Mardware Configuraten Tegholder Web Help Topics baleen ad LJ Site Configuration Ste Properties She NETE Nen Ste She Rretho Addens Ortar af i gt ka la Corfou on Leve Qedad Coffins ter Adv aried Config stor a vE Transaction Viewer Aam Transacton herer Communications Satus Viewer Door Status vewe Ste Seq Date Teme ermana Evert we Tas tern Ste 6 este e 0206 DPN Emergency Undock Off burn Ste 5 O 10100 DPIN Power Up bien Ste 2 e x 17 a9 100 DPO Emergency Untock Off been Ste 1 D0902 17 28 59 OG DPN Power Up A ordre ConfigOverview_01 300 jpg Figure 5 IXP220 Work Area The IXP220 Base Application only displays as shown in Figure 5 where you select the standard Windows Vista Business or Ultimate and XP Professional themes Using other non standard themes results in IXP220 displaying incorrectly ewww impro net e March 2009 Page 19 ISW302 0 0 GB 00 The following parts comprise the IXP220 Base Application s interface A Menu Bar Contains drop down menus that let you navigate between
10. he Wizard pops up twice installing two drivers one for the USB Registration Reader and one for the COM Port to USB Bridge ewww impro net e ISW302 0 0 GB 00 March 2009 Page 6 D Pre configuration Procedure When all IXP220 Software components are installed you need to perform the Pre configuration Procedure This procedure determines if the hardware communication infrastructure is functioning correctly RS485 Communications Infrastructure 1 Using the supplied USB Cable connect the ImproX RS to the PC 2 Using the IXP220 Controller s RS485 Controller Port connect the IXP220 Controller to the ImproX RS USB Communications Infrastructure 1 Plug the IXP220 Controller into a USB port on the PC The Found New Hardware Wizard displays 2 Select the Locate and Install Driver Software Recommended option 3 Select don t have the Disk Show me Other Options 4 Select the Browse My Computer for Driver Software Advanced option 5 Click the Browse button 6 Inthe Browse for Folder dialog select the IXP220 USB_ Device _Driver folder 7 Click the OK button 8 Click the Next button 9 Atthe Windows Security dialog select the Install this Driver Software Anyway option Take note of the COM Port number displayed by the Driver i Software Installation dialog 10 Click the Close button ewww impro net o ISW302 0 0 GB 00 March 2009 Page 7 TCP IP Communications Infrastructure Start the Discovery Utility I
11. impro IXP220 Software QUICK START GUIDE Scope of Document This document gives a brief overview of the IXP220 System Document Conventions We use the following conventions in this document Note points out extra information Tip points out alternative methods to perform a task Important points out important information Warning points out potential danger to you or the product Before You Begin Have the following available e An active Ethernet connection to the IXP220 Controller e The IXP220 Software Suite e The MAC Address and Fixed Address of each IXP220 Controller on a label bundled with the Controller ewww impro net e Installation IXP220 Software Installation Procedure Install the IXP220 Software Suite on a single Host PC as follows 1 Insert the IXP220 Installation CD into the CD ROM drive 2 Select the Install IXP220 Suite option P If the CD does not start up automatically browse the CD in Windows Explorer and double click Setup exe 3 Select English as the language option 4 Click the OK button If no Database Server is present one is installed Follow the onscreen instructions for this 5 At the Introduction screen click Next 6 At the Licence Agreement screen select the Accept the Terms of the Licence Agreement radio button 7 Click the Next button 8 Atthe Choose Install Folder screen click Next lf you change the installation dire
12. ions below continue as for an Advanced Configuration For a Standard Configuration ignore references made to fields that appear greyed out In the Communications group from the Communication Schedule drop down list select a Communication Schedule If you wish to communicate only with the selected site select the Communicate Exclusively checkbox From the Poller Configuration group click the Set Parameters button Setthe Polling Frequency seconds how often Doors Locations get polled for their status Set the Door Open Time Limit seconds normal duration Doors Locations remain open From the Time Zone drop down list make your selection ewww impro net e ISW302 0 0 GB 00 March 2009 Page 17 Set the Apply Daylight Saving option as follows 1 Alongside Apply Daylight Saving click the Yes radio button 2 Click on the Set Daylight Saving button 3 Inthe Set Daylight Saving dialog set the Time Offset Start Date Start Time End Date and End Time 4 Click the amp button 9 Click the ka button Controller Configuration 1 Select the ta Page Tab 2 Inthe Controller Name textbox assign your Controller a suitable name 3 From the APB Configuration group adjust the following settings Set the APB Lockout Delay on Entry minutes the same Tagholder may not pass this same entry access point within the specified time period Set the APB Lockout Delay on Exit minutes the same Ta
13. led information on Site setup please refer to Part III of the IXP220 Software Installation Guide Or alternatively refer to the WebHelp included with the IXP220 Software ewww impro net o ISW302 0 0 GB 00 March 2009 Page 22 Extra Information Further information is available at the following resources e IXP220 Software Installation Guide ISW300 0 0 GB XX e IXP220 WebHelp ISW390 0 0 GB XxX e IXP220 Software Product Specification Catalogue ISW350 0 0 GB XxX e Ethernet Discovery Utility Software User Manual ISW301 0 0 GB XX e ImproX IXP220 Controller Product Specification Catalogue ISC350 0 0 GB XX e ImproX IXP220 Controller Installation Manual ISC300 0 0 GB XX The referenced documents are available for download at www impro net Alternatively contact your Impro dealer for a copy User Notes ewww impro net o ISW302 0 0 GB 00 March 2009 Page 23 User Notes This manual is applicable to the IXP220 Software Suite V1 80 upwards The last two digits of the Impro stock code indicate the issue status of the product IXP220 Software English Manuals LATEST ISW302 0 0 GB 00 Mar 2009 ISSUE 220QSG swm en 01 docx ewww impro net o ISW302 0 0 GB 00 March 2009 Page 24
14. mmunications Status Viewer indicates the status of the IXP220 Controllers communicating with the IXP220 System e Door Status Viewer indicates the status of the Doors Locations forming part of the Site You may physically unlock Doors Locations displayed here using the IXP220 Software Using Help P The Context Sensitive WebHelp provided with the IXP220 Software works with your positioned Mouse Pointer or cursor on your screen For example if you place your Mouse Pointer in the Viewer Pane WebHelp opens Context Sensitive WebHelp specific to the Viewer Pane If however you want WebHelp specific to the active Configuration Pane continue as follows 1 Move your Mouse Pointer into the Configuration Pane 2 Anchor your Mouse Pointer by clicking the left hand button on your mouse thus ensuring the Pane has focus 3 Press the F1 key on your keyboard The IXP220 System has integrated context sensitive WebHelp Information not covered in this guide is covered in detail in the WebHelp ewww impro net o ISW302 0 0 GB 00 March 2009 Page 21 Activate the WebHelp as follows 1 In Windows go to Start gt Programs gt IXP220 gt IXP220 2 From the Menu Bar select Help Topics gt Online Help Site Setup Perform Site setup in the following order Site Configuration Controller Configuration Door Configuration Access Group Configuration Tagholder Configuration Holiday Configuration Full Upload Oo so hy For detai
15. n Windows go to Start gt All Programs gt IXP220 gt Utils gt Ethernet Discovery Utility Lj Alternately access the Ethernet Discovery Utility direct from the IXP220 Base Application From the Menu Bar select Hardware gt Unit Discovery View all Available Controllers To view all the IXP220 Network Controllers on the local subnet 1 On the Menu Bar go to Network gt Search Local Subnet 2 If the Discovery Application fails to find any Devices at the Device Not Found dialog click the OK button 3 On the Menu Bar go to Network gt Advanced Local Search P By selecting Advanced Local Search you may 1 Select the correct Network Interface only displayed where more than one exists 2 Enter the correct Subnet Mask If the search returns Controller details then the Discovery Application while running retains the Network Interface and Subnet Mask information captured for further searches You may however use the Advanced Local Search feature again during the session for further searches using different search criteria 4 Atthe Select Network Interface dialog select the relevant Network Interface if more than one displays 5 Click the OK button ewww impro net e ISW302 0 0 GB 00 March 2009 Page 8 6 Inthe Input dialog in the textbox enter the Subnet Mask for your network 7 Click the OK button 8 Wait for the Controllers to display Sort the information displayed in either ascending or descending orde
16. og again click on the Add Port button Set the Ethernet Firebird Port by completing the Name for example Firebird Service and Port Number Ethernet communication uses 3050 Select the TCP radio button Close the Add a Port dialog by clicking the OK button Close the Windows Firewall Settings dialog by clicking the OK button ewww impro net e March 2009 Page 3 Installing the Firebird 2 1 Database Server A Database Server is required to host the IXP220 Database If the IXP220 Suite is installed on to a single PC the Database Server installs automatically However if more than one PC is used to host the IXP220 software you must install the Database Server manually Firebird automatically prompts to install if a previous version is not detected As any PC on the network can host the Database Server select a PC to host the Database Server Insert the IXP220 Installation CD in the PC s CD ROM drive Browse to the database firebird directory on the IXP220 Installation CD Double click Firebird exe In the Select Language Setup dialog from the drop down menu select your preferred language Click the OK button Firebird Installation Wizard 1 At the Welcome dialog review and follow the on screen instructions Click the Next button At the Licence Agreement dialog select the Accept the Agreement radio button Click the Next button Review the Information dialog and then click the Next button In
17. p Support option 11 Click the Next button 12 Click the Install button 13 Review the Information dialog and then click the Next buiton 14 Click the Finish button ewww impro net e ISW302 0 0 GB 00 March 2009 Page 5 Installing the USB Registration Interface s USB Driver IXP220 uses a USB Registration Reader Interface to read Tags Some Interface versions also provide an RS485 communication link to the Controllers To install the driver proceed as follows Oo G On some PC s the New Hardware Found wizard displays If there are old USB Drivers on the PC delete them before installing the provided driver every time you plug in a USB Registration Reader Interface with a new USB Serial Number Fixed Address If this happens choose the option to automatically install the unit The New Hardware Found wizard will not display again Plug the USB Registration Interface into a USB port on the PC The Found New Hardware Wizard displays Select the Locate and Install Driver Software Recommended option Select don t have the Disk Show me Other Options Select the Browse My Computer for Driver Software Advanced option Click the Browse button In the Browse for Folder dialog select the IXP220 USB_Device _Driver folder Click the OK button Click the Next button At the Windows Security dialog select the Install this Driver Software Anyway option 10 Click the Close button You will notice that t
18. r by selecting the column header The arrow displayed in the column header indicates whether sorting is ascending or descending and the column on which the sort took place View a Specific Controller To view a specific Controller 1 Onthe Menu Bar go to Network gt Search IP 2 Inthe Enter IP Address dialog enter the IP Address of the Controller you re searching for 3 Click on the amp button 4 Wait for the Controller to display Secure Logon The default password is masterkey for improved security we recommend that you change this password 1 Inthe Device Password dialog enter your password 2 Click on the button ewww impro net o ISW302 0 0 GB 00 March 2009 Page 9 Configure IP Addresses If you do not know your Configuration Settings contact your Network Administrator lf a DHCP server is present IP Addresses are dynamically assigned initially Obtain a suitable IP Address from your Network Administrator A static IP Address is essential for the Controller because a DHCP Server may assign a new IP Address resulting in the Software losing communications Configure a Controller s IP Address settings as follows 1 Inthe Ethernet Discovery Utility window select the Controller for configuration 2 From the Menu Bar select Network gt Configure IP 3 Logon if requested see page 9 Ay Configuration Settings Device MAC Address 00 1A 6E 00 0B 51 Device IP Address 192 1 0 238 Gateway IP
19. work 3 Click the OK button 7 From the list of devices displayed in the AutolID Channel column make your selection 8 Click the E button P Connecting Controller A via the network and Controller B connected to Controller A by RS485 lets you configure both Controllers at the same time P After performing Auto ID review the log of identified units by E selecting Hardware gt Latest Auto ID Log from the Menu Bar This feature lets you check whether Auto ID has missed any terminals possibly because of a wrong DIP switch setting or faulty communications ewww impro net o ISW302 0 0 GB 00 March 2009 Page 16 Firmware Version Confirmation After physically connecting powering up and identifying the ImproxX Hardware confirm whether a Firmware upgrade is required The Firmware Revisions dialog indicates the Unit Type along with the Latest Firmware revision available and the Current Firmware version in use by the unit Access the Firmware Revisions dialog by selecting Hardware gt Firmware Version Check from the Menu Bar See the Software Installers Guide Part VII Utilities for more information on the Firmware Upgrade Utility Configure the Site e ON gt If not already selected select the o Page Tab In the Configuration Pane complete the Site Name textbox Complete the Site Street Physical Address text area Select either the Standard Configuration or the Advanced Configuration radio button The instruct
Download Pdf Manuals
Related Search