Mini Par User Manual
Contents
1. 1 7 groups ID code press KEY for setting it only can works under same ID code of transmitter and receiver NOOB WD Establishing Communication Power on DMX512 wireless received board and transmitted board Press Key button to set same ID value of transmitted board and received board please use different ID value if you need use more than 1 group wireless net at same time in same place The red LED flashes when transmitter transmits DMX data by no interfered frequency section then receiver changes communicated frequency section Green LED flash till received corrected same ID value LED flash faster once DMX data more fast Communication was established correctly then Cleaning Due to fog residue smoke and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light output 1 Use normal glass cleaner and a soft cloth to wipe down the outside casing 2 Clean the external optics with glass cleaner and a soft cloth every 20 days 3 Always be sure to dry all parts completely before plugging the unit back in 4 Cleaning frequency depends on the environment in which the fixture operates i e smoke fog residue dust Trouble Shooting Listed below are a few common problems the user may encounter with solutions Unit not responds to DMX 1 Check that the DMX cables are connected properly and are wired correctly pin 3 is hot on some other DMX devices p2. matter Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to the point they exit from the unit 2 Control Channels 6CH Master Slave synchronization Electronic Dimming 0 100 LED operation menu with function buttons Daisy Chain Units Together in DMX Mode 000005000006 Cleaning The fixture should be cleaned only as recommended by the manufacturer See Cleaning for details Heat The appliance should be situated away from heat sources such as radiators heat registers stove or other appliances including amplifiers that produce heat The fixture should be serviced by qualified service personnel when A The power supply cord or the plug has been damaged B Objects have fallen or liquid has been spilled into the appliance C The appliance has been exposed to rain or water D The appliance does not appear to operate normally or exhibits a marked change in performance Fuse standard is 2A 250V Grounded using yellow green line The ambient temperature must always be under 35 C Set Up Power Supply Before plugging your unit in be sure the source voltage in your area matches the required voltage for your MINI PAR The MINI PAR is workable in 100 220V 50 60Hz Because line voltage may vary from venue to venue you should be sure your unit voltage matches the wall outlet voltage before attempting to
3. Mini Par User Manual Tri LED 9 CE Please read over this manual before operating the light Introduction Unpacking Thank you for purchasing the Mini PAR Every Mini PAR has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during shipping If the carton appears to be damaged carefully inspect your fixture for any damage and be sure all accessories necessary to operate the unit have arrived intact In the case damage has been found or parts are missing please contact the manufacturer or your dealer for further instructions Do not return this unit to your dealer without first contacting Introduction The Mini PAR is a DMX intelligent LED par light This par light is lightweight and compact which makes it a great piece for mobile DJ s and clubs Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures warranty In the unlikely event your unit may require service please contact the manufacturer or your dealer PLEASE recycle the shipping carton whenever possible General Instructions To optimize the performance of this product please read these operating instructions carefully to familiarize you with the basic operations of this unit These instructions conta
4. ch the button for battery to bat on When charge the light please switch the button for battery to charge At the same time if the switch for power is on the light will be at work during the process of charge but will consume some power from the charge if the switch for power is off the light will be blackout and not be at work Tip for the battery and charge The battery can last for 6 hours when all LEDs on after full charge and can last for more than 10 hours on auto running mode Itis suggested to charge the battery for at least 8 hours which will extend the life span of the battery Atthe bottom of the fixture there is a little hole which is the indicating light for the charge When charge the light the indicating light will be in red and when charged full it will be in green Wireless Module of DMX512 MODE PCB WI DMX Brief DMX512 wireless receiver transmitter transmits standard DMX512 protocol data generated by console by wireless way which solves lighting control issues of wireless transmitting completely between console and lighting lighting and lighting and so on It get rid of connecting cable limited completely And also can ensure without any time delay when signal data is transmitting signal data is real time and reliably This product adopt 2 4G ISM freguency section global opening section without permission limited High effective GFSK modulate communication design 126 chan
5. in 2 may be hot Also check that all cables are connected to the right connectors it does matter which way the inputs and outputs are connected Unit does not respond to sound 1 Quiet or high pitched sounds will not activate the unit If problems are not resolved contact your dealer for service Specifications Model Mini PAR Working Position Any safe working position Power Supply Switching power supply Voltage AC 100 220V 50 60Hz Power Consumption 30W Colors RGB Color Mixing LED 9 pcs 3in1 Gross Weight 1 3Kgs Dimensions 200 L x 100 W x 200 H mm Note All information is subject to change without prior notice 2011 01 01 Ht
6. in important safety information regarding the use and maintenance of this unit Please keep this manual with the unit for future reference Features e Multi Colors Color Strobe DMX 512 protocol Operating Modes Sound activation Auto and DMX control mode e 1 20 flashes sec strobe effect Safety Precautions To reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Do not spill water or other liquids into or on to your unit Be sure that the local power outlet match that of the reguired voltage for your unit Do not attempt to operate this unit if the power cord has been frayed or broken Do not attempt to remove or break off the ground prong from the electrical cord This prong is used to reduce the risk of electrical shock and fire in case of an internal short Disconnect from main power before making any type of connection Do not remove the cover under any conditions There are no user serviceable parts inside Never operate this unit when it s cover is removed Never plug this unit in to a dimmer pack Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm tween this device and a wall Do not attempt to operate this unit if it becomes damaged This unit is intended for indoor use only use of this product outdoors voids all warranties During long periods of non use disconnect the unit s main power Always mount this unit in safe and stable
7. n To set the LED display off when idling for 50 seconds Enter to set the words in the LED display up side down To show the used hours of the unit W 1 512 Da RE T T DMX Values and Functions Channel 0 255 Red dimmer 0 100 0 255 Green dimmer 0 100 0 255 Blue dimmer 0 100 0 15 No function Enable all other channels 16 255 7 color changing from slow to fast Disable all other channels 5 0 127 No function 128 255 Master strobe for R G and B channels from slow to fast RE CH1 CH2 and or CH3 should be activated p 31 No function sr Master dimmer for R G and B channels 0 100 For Battery Function and Charge The unit has the function of battery powered The button for battery and charge is set on the rear panel It is showed as the following picture and the function is described as below 9 Power socket and fuse holder 10 Fixation screw 11 Mounting bracket 1 Alpha numeric display 2 Touch switches 3 Microphone 4 DMX In socket 5 DMX Out socket 6 Power switch 7 Battery switch 8 GND There are two buttons on the rear panel of the lighting One is for power and the other is for battery When use the fixture with DMX not battery please switch the button for power to on and switch the button for battery to bat off When use the fixture with battery instead of DMX please switch the button for power to off and also swit
8. nels jumping freguency automatically high anti jamming ability Application Upgrade DMX512 stage lighting PCB Hole Receiver Frequency Selector 13 Led Indicator Light Product feature Product name 2 4G wireless DMX512 R T molding board Small size Easy to suit for interior of accessed lighting Single key to operate tricolor LED displaying Transmitting standard DMX512 protocol data of console also can transmitting lighting and lighting DMX512 protocol data 126 channels jumping freguency automatically high anti jamming ability to ensure works reliability 7 groups ID code settable User can use 7 groups individual wireless net without any interfere each other in the same place Input voltage 5VDC Work frequency section 2 4G ISM 126 channels frequency section Max transmitting power rate 20dBm Receiver sensitive 94dBm Signal port RS485 or CPU series port AURT LCD WI DMX ID 0 15 RAD WI DMX ID 1 7 XRL WI DMX ID 1 7 Operating manual ID code and LED color corresponding relationship RED GREEN RED GREED BLUE RED BLUE GREEN BLUE RED GREED BLUE Press key 1 time to indicate ID setting Press again to set ID then ID value adding 1 each time by press Working condition LED constant lit up no DMX or wireless signal Red LED flash transmitting Green LED flash receiving RF frequency 2 400 2 525 G total 126 channels it s searching automatically ID Code
9. operate you fixture DMX Linking To ensure proper DMX data transmission when using several DMX fixtures tries to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain Operating Instructions Operating Modes You can use the Mini PAR in 4 ways Sound activation The unit will activated by the sound signal Static display The unit will display the pattern in static way Auto Mode The unit will automatically chase through the different patterns DMX control mode This function will allow you to control each individual fixtures traits with a standard DMX 512 controller DMX Mode Operating through a DMX controller give the user the freedom to create their own programs to their own individual needs This function also allows you to use your fixtures as pattern changing lights 1 This function will allow you to control each individual fixture s traits with a standard DMX 512 controller 2 The Mini PAR uses 6 DMX channels to operate Please see DMX Values and Functions for the DMX traits 3 To run your fixture in DMX mode plug in the fix
10. ture via the XLR connections to any standard DMX controller Set your desired DMX address following the setup specifications that come with your DMX controller 4 The unit can automatically recognize the DMX signal once the DMX connection is done Touch Buttons There are four touch buttons under the LED display Menu Down Up Enter Normally the LED will display the current DMX address code of the fixture At this time presses Menu to choose the function you want to set up Press and hold Up or Down to fast scrolling within the menu options When an option is flashing the LED display press Enter to confirm and Menu to exit LED Operation Menu After initialization the unit is ready for setting and working Please see the following table for setting information To set DMX starting address To set as master unit Only one unit in a chain can be set as master To set as slave unit When it shows St the slave mode is ready Press for three MENU seconds to activate the sound activation mode Press MENU again for three seconds to quit PLO1 PL16 PLO1 Red PLO2 Green PLOS Blue PLO4 Red Green PLOS Red Blue PLOG Green Blue PLO7 Full On PLO8 Red Strobe PLOY Green Strobe PL10 Blue Strobe PL11 Red Green Strobe PL12 Red Blue Strobe PL13 Green Blue Strobe PL14 Full On Strobe PL15 RGB Color Changing PL16 7 color changing SP01 SP08 Speed of PLAY strobe amp color changing To keep the LED display always o
Download Pdf Manuals
Related Search