Leica FlexLine TS02 TS06 TS09 Mining Application
Contents
1. Point ID Northing Elevation Backsight Point Grade Elevation 55 987 90 265 P100 88 265 88 365 60 325 91 354 P101 90 365 3 Save the created coordinate list File gt Save As Define tolerances For defining tolerances ensure that the unit setting on the instrument select step by step Settings gt General is identical to the units set in the Mining Editor select Options gt Settings Step Description 1 Open tolerances Options gt Tolerances gt Edit 2 Enter the password Mining Editor FlexLine 39 Mining Editor FlexLine 40 Step Description Ee To create a new password Options gt Password 3 Select a measuring sequence BFFB BFBF or BBFF Ee B Backsight point F Foresight point 4 Enter the number of sets On the Limits tab select a tolerance type Primary Secondary or Tertiary I Sequence Limits Tolerance Profile fFimy o O Horizontal Angle Limit 0 0065 gon Horizontal Distance Limit 0005 m Height Limit food m Cancel Apply Uploading step by step Step Description Enter the values for e Horizontal Angle Limit e Horizontal Distance Limit e Height Limit Press OK to save the tolerances Refer to Uploading step by step to upload tolerances to the instrument Step Description Connect the instrument via the serial interface RS232 to the compu2. Peg Survey FlexLine 16 Measure points step by step Step Description Enter the reflector height hr for the backsight point if required Aim at backsight point and press MEASURE Depending on the measurement sequence selected enter a desired backsight or foresight point ID PtID OK saves the point ID and proceeds to the measurement screen Enter the reflector height hr for the point if required Aim at target point and press MEASURE Decide whether to measure an additional point e NO Repeat steps 2 and 5 until all sets are measured e YES Repeat steps 3 to 5 with a new point C amp A maximum of 7 additional points can be measured If the tolerances after a set are not met the user has the option to continue with the measurements or reject the data e REJECT to reject the measurements and remeasure the set again e ACCEPT to accept the result and continue with the next set Next step After each set the TOLERANCES MET or the Out of tolerance screen displays TOLERANCES MET TOLERANCE INFO 1 2 Tolerances met ae FS ID 3 dHz 4 0 00 25 Toi Hz 0 00 50 ok dHD BS 0 007 m To proceed to the results screen dHD FS 0 003 m EXIT Tol HD 0 006 m To exit the application and return to the PEG SURVEY settings screen Description of fields Field Description BS FS ID Point ID for backsight and fore
3. correct format 5 Save the created file File gt Save as Mining Editor FlexLine 43 Index FlexLine 44 Index A 0 Applications Offset descriptiOncOF ccc cava disncacuedeaes 33 Grades riens Giasdies 23 p Line peg 22 Offset 32 PIN code set 4 8 PAS SUIVOCY wicsccetecescsciecseus a aa Lk APANERE EE 9 s H Sequence description cceceeeeeeseeeeeeeeeseeeeeees 13 Height difference description ccccccecceeeees 24 Sets description Serer teceeeeeeteeeeeeeeeeetsenesneneeanees 12 Slope gradient description ecceseeeeeeeeeeteeeees 24 l Symbols used in this manual eeeeeeeeeeeeeees 2 Installation of mining editor cceeeeeeeeeee 38 T M Tolerances Mining editor Defining Creating fixpoint files eeren 39 Met scccsines cuts Defining tolerances 39 Select profile Tale LR LUS serors dsns iienaa 39 Installation 38 Process imported files n se 42 Software oe eeeeeececeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeesenenaeees 38 Uploading Index FlexLine 45 Total Quality Management Our commitment to total customer satisfaction Leica Geosystems AG Heerbrugg Switzerland has been certified as being equipped with a quality system which meets the International Standards of Quality Management and Quality Systems ISO standard 9001 and Environmental 1S0 9001 1SO 14001 Management Syste
4. distance to the foresight point mHBS Average height of the back sight point mHFS Average height of the fore sight point Saving the data The following results are stored in the internal memory Field Description Result mHz Average horizontal angle between backsight point and foresight point mHD Average horizontal distance to backsight and foresight points mH Average height to backsight and foresight points Residual dHz Horizontal angle residual dHD Horizontal distance residual Field Description dH Height residual Coordinates foresight point E Easting N Northing H Height point GrEl Grade elevation Next step Press OK to save the data and exit the application The CONTINUE WITH screen appears for access to the GRADES or OFFSET applications Refer to 4 2 Starting Grades and 5 2 Starting Offset Peg Survey FlexLine 21 Line Peg FlexLine 22 3 Line Peg Description The application Line Peg is used to mark a new line peg This application is similar to Peg Survey except there is only one set of measurements required For the Line Peg application follow the procedure described in 2 Peg Survey 4 Grades 4 1 Overview Description The Grades application is used e to mark gradelines along the side walls of the mines or tunnels e to input the slope gradient and an offset concerning the grade point e to compute the stake out height d
5. establish a forward peg point e to control the intermediate horizontal angle between backsight and foresight points e to check the horizontal distances and heights of the backsight and foresight points e to compute the coordinates of the foresight point Users can measure several sets in different sequences The quality of measurement is controlled by the tolerances which are set before starting Peg Survey Station Backsight point Foresight point Height of the reflector Height of the instrument Distance to backsight point Distance to foresight point Horizontal direction to backsight point Horizontal direction to foresight point Peg Survey FlexLine 9 Peg Survey FlexLine 10 Known e Coordinates of station e Coordinates of backsight point Unknown e Coordinates of foresight point 2 2 Access Input station step by step Starting Peg Survey 1 Select Prog from the MAIN MENU 2 Select Peg Survey from the PROGRAMS menu 3 Complete the application pre settings by e Se ecting a job and e Confirming the set of tolerances Refer to 1 2 Selecting Tolerance Profiles 4 Select Start to proceed to Input Station Step Description I Enter the point ID PtID 2 For manual entry of instrument height e Enter instrument height hi of the station For measuring the instrument height e Turn the telescope to the azimuth with the help of the displayed ver
6. Leica FlexLine TSO2 TSO6 1509 Mining Application Version 1 0 j English when it has to be right Sica Geosystems Introduction FlexLine 2 Introduction To use equipment in the permitted manner please refer to the detailed safety A instructions in the FlexLine TS02 TS06 TSO9 User Manual Symbols The symbols used in this manual have the following meanings Type Description Ee Important paragraphs which must be adhered to in practice as they enable the product to be used in a technically correct and efficient manner EE Press the function button F1 to F4 A Navigation keys Table of Contents In this manual Chapter Page 1 Tolerances 5 1 1 Defining Tolerances 5 1 2 Selecting Tolerance Profiles 7 1 3 PIN Personal Identification Number 8 2 Peg Survey 9 2 1 Overview 9 2 2 Starting Peg Survey 11 2 3 Measuring Peg Survey 15 2 4 Peg Survey Results 19 3 Line Peg 22 4 Grades 23 4 1 Overview 23 4 2 Starting Grades 25 4 3 Gradeline Marking 27 4 4 Grade Results 30 5 Offset 32 5 1 Overview 32 Table of Contents FlexLine 3 Table of Contents FlexLine 4 5 2 Starting Offset 34 5 3 Offset Results 37 6 Mining Editor 38 6 1 Overview 38 6 2 Functionality 39 Index 44 1 1 1 Description Access ES Define tolerances step by step Tolerances Defining Tolerances Before use of the mining applications tolerance profi
7. Select either a Primary Secondary or Tertiary tolerance profile to be applied 5 Press SET to set the selected profile 6 Press ACCEPT to accept the profile in the tolerances summary screen OR REJECT to reject the profile and return to the define tolerance profile screen CE e Tolerances themselves can be changed by using the PIN protected Define Tolerance application Refer to 1 1 Defining Tolerances e Ifa tolerance was uploaded by the Mining Editor software this tolerance will appear as Uploaded and cannot be changed on the instrument Tolerances FlexLine 7 Tolerances FlexLine 8 1 3 Description Set PIN code step by step PIN Personal Identification Number The definition of tolerances is PIN protected to prevent unauthorised changes The PIN is definable by the user If a wrong PIN has been typed in 5 times a Personal UnblocKing code PUK is required which can be found on the instrument delivery papers If the entered PUK code is correct then the PIN code is reset to default value 123456 Step Description 1 Select Setting from the MAIN MENU Select Mining from the SETTINGS MENU Enter the current PIN in PIN CODE Press OK Enter a personal PIN Code max 6 characters numeric in New PIN Code Accept with OK Oy St ay ON The default PIN is 123456 2 2 1 Description Peg Survey Overview The application Peg Survey is used e to
8. ceed to measure another point Grades FlexLine 29 Grades FlexLine 30 4 4 Grade Results Description The Grades application computes the height difference dHgt between the measured point and the stake out point and the difference in horizontal distance dHD along the foresight line Profile view PO Station P1 Foresight point de a Gradeline dHgt Difference in height dHD Difference in horizontal distance PO Station P1 Foresight point a New gradeline point dHD Difference in horizontal distance Saving the data The following results are stored in the internal memory Field Description Measurement data PtID Point ID Hz Horizontal angle V Vertical angle HD Horizontal distance SD Slope distance dH Height difference Coordinates of new gradeline point E Easting N Northing H Height Grades Result daH Stake out height difference daHD Horizontal distance along the foresight line Grd Slope gradient GE Grade elevation Grades FlexLine 31 Offset FlexLine 32 5 Offset 5 1 Overview Description The Offset application is used e to record sections of the tunnels for volume computation and mapping e to input an offset value left right up or down e to compute after measurement the actual coordinates of the tunnel walls Known e Coordinates of station e Coordinates of backsight point e O
9. dHz Tolerated residual in horizontal direction dHD Tolerated residual in horizontal distance dH Tolerated residual in height Peg Survey FlexLine 13 Peg Survey FlexLine 14 Next step Step Description T Press OK to proceed to the number of sets screen The number of sets screen displays which set is about to be measured out of the total number of sets remaining For example Set 1 of total 3 means the measurement will be the first set of three 2 Press OK to proceed to the Measure Backsight Point screen The Measure Backsight Point screen displays information about which backsight point the user has to measure 3 Press OK to proceed to the backsight point measurement screen 2 3 Access Backsight Point Foresight Point Measuring Peg Survey Press OK from the Measure Backsight Point screen Backsight Point 1 263 MEASURE P 1D 1 To start angle and distance measure Hz 100 47 59 pa and save the measured rien values K 74 539 16 SEARCH hr To search for a different backsight point EXIT To exit the application and return to the PEG SURVEY settings screen Foresight Point 1 263 PTtID 3 ia 2 4 190 48 00 DIST 74 59 16 To start distance and angle measure ee 1 632 n jo without saving the measured D NN 777 m y GRADE To edit current grades Refer to 4 Grades Peg Survey FlexLine 15
10. ffset value Unknown e Point coordinates of the tunnel walls Station Backsight point Foresight point Offset Profile view TSOX Mining 011 Top view TSOX Mining_012 angu Up Left Right Down Station Foresight point Offset left Offset right Offset FlexLine 33 Offset FlexLine 34 5 2 Starting Offset Access The Offset application is started by either selecting it in the PROGRAMS menu or Starting offset step by step after measuring in the applications PEG SURVEY and LINE PEG When started from the PROGRAMS menu station data must be entered and a measurement made to backsight and foresight points first before the Offset application can be used Step Description 1 Select Prog from the MAIN MENU 2 Select GRADES amp OFFSET from the PROGRAMS menu and complete the application pre settings by e Selecting a job and Confirming the set of tolerances Refer to 1 2 Selecting Tolerance Profiles Select Start to proceed to the Input Station screen Input station data and measure to the backsight and foresight points Refer to 2 Peg Survey for details on this process Accept the tolerances from the measurements In the CONTINUE WITH screen press OFFSET to start the Offset application OFFSET Offset step by step OFFSET 69 MEASURE PHID FP10 To start angle and distance measure offset 1 500 m ments a
11. ifference e to map the positions of the grade points along the gradelines TSQK Mining_005 Station Backsight point Foresight point New gradeline Measured points New gradeline points Horizontal distance along the foresight line Current height of gradeline above mine floor Height difference to new gradeline Grades FlexLine 23 Grades FlexLine 24 Known e Coordinates and grade elevation of station e Coordinates and grade elevation of backsight point e Slope gradient station to foresight point e Height difference dH between current gradeline and new gradeline Unknown e Stake out height difference dHgt between measured point and gradeline point e Horizontal distance dHD along the foresight line Slope gradient ee a Gradeline Td h Height d Vertical distance racine 06 d Height difference PO Station P1 Foresight point a New gradeline b Current gradeline H Current height of gradeline above mine floor dH Height difference between current gradeline and new gradeline 4 2 Access Starting grades step by step Starting Grades The Grades application is started by either selecting it in the PROGRAMS menu or after measuring in the applications PEG SURVEY and LINE PEG When started from the PROGRAMS menu station data must be entered and a measurement made to backsight and foresight points first before the Grade application can be used Step Desc
12. is a Windows based program used for the data exchange between the instrument and a computer The installation program for the Mining Editor can be found on the CD ROM supplied Please note that the Mining Editor can only be installed under the operating systems MS Windows 95 98 ME NT4 0 WINDOWS2000 or WINDOWSXP For the installation select setup exe in the directory MiningEditor Disk1 on the CD ROM and follow the onscreen instructions to complete the installation The Mining Editor can be used for the following purposes Creating fixpoint files Creating and editing of fixpoint files such as coordinates Defining and uploading tolerances Defining editing password protected and uploading tolerances Data import and export Importing and exporting fixpoint files ASCII format Data transfer between computer and instrument Uploading of fixpoint files and tolerances downloading of fixpoint files and measurement data and conversion of measurement data to various formats for peg calculation and archiving 6 2 Functionality Creating fixpoint In the fixpoint entry module the Mining Editor allows users to create view modify files step by step and save coordinate lists Step Description 1 Open a new file File gt New 2 Enter point IDs and for each one coordinates a backsight reference point and a grade elevation aE Eile Edt View Data Options Window Help l8 OSHS 4B BANV
13. les have to be defined and selected The definition of tolerances can be done either via the Mining Editor software or manually on the instrument This chapter describes defining and selecting tolerances manually Refer to 6 Mining Editor for details on using the Mining Editor software 1 Select Prog from the MAIN MENU 2 Select Define Tolerances from the PROGRAMS menu 3 Enter the current PIN 4 Press OK to proceed to the tolerance profile screen If a wrong PIN has been typed in 5 times a Personal UnblocKing code PUK is required which can be found on the instrument delivery papers If the entered PUK code is correct then the PIN code is reset to default value 123456 Step Description 1 Select the tolerance profile to define Primary Secondary or Tertiary 2 Enter the limits for horizontal direction horizontal distance and height 3 Select the preferred sequence BFFB BFBF or BBFF and number of sets Ee B Backsight point F Foresight point Tolerances FlexLine 5 Tolerances FlexLine 6 Step Description 4 Repeat steps 1 to 3 for each of the three tolerance profiles 5 Set the defined tolerances by pressing SET 1 2 Select tolerances Selecting Tolerance Profiles Step Description step by step 1 Start a mining application 2 Select Set Tolerances 3 Select Select Tolerances 4
14. ms ISO standard 14001 Ask your local Leica dealer for more information about our TQM program Leica Geosystems AG Heinrich Wild Strasse CH 9435 Heerbrugg Switzerland Phone 41 71 727 31 31 when it has to be right www leica geosystems com Original text Printed in Switzerland 2008 Leica Geosystems AG Heerbrugg Switzerland 767508 1 0 0en eca Geosystems
15. nd save the measured values BE ist To start distance and angle measure ments without saving the measured values EXIT To exit the application and return to the CONTINUE WITH screen Step Description k Enter a desired point ID PtID and the offset value 2 Select the offset definition Left Right Up or Down 3 Aim at the target point and press MEASURE The measurement is triggered and stored C After storing the application returns to the OFFSET screen 4 To measure a new point repeat steps 1 to 3 Offset FlexLine 35 Offset FlexLine 36 Next step Press MEASURE to measure and record data for the current point and proceed to measure another point 5 3 Offset Results cE The measurement data is already corrected according to the offset values Saving the data The following results are stored in the internal memory Field Description Measurement data PtID Point ID Hz Horizontal angle V Vertical angle HD Horizontal distance SD Slope distance Offset information Offset Offset value OffsetDir Offset direction left up right down Coordinates of new offset point E Easting N Northing H Height Offset FlexLine 37 Mining Editor FlexLine 38 6 6 1 Description Installation on the computer Program content Mining Editor Overview The Mining Editor
16. ription alk Select Prog from the MAIN MENU 2 Select GRADES amp OFFSET from the PROGRAMS menu and complete the application pre settings by e Selecting a job and e Confirming the set of tolerances Refer to 1 2 Selecting Tolerance Profiles Select Start to proceed to the Input Station screen Input station data and measure to the backsight and foresight points Refer to 2 Peg Survey for details on this process Accept the tolerances from the measurements In the CONTINUE WITH screen press GRADES to start the Grade application Grades FlexLine 25 FlexLine 26 Grades GRADES Enter the slope gradient as a proportion for example 1 150 and the height difference f the slope gradient from the station to the foresight point is the same as the slope gradient from the backsight point to the station then no gradient needs to be entered GRADES SET Grade 1 x 1 To save the current values Grade Z 24 25 7 CHAIN Grade Ang 13 38 00 To enter a chain length instead of a Direction Down 4 gradient Height 0 500 m EXIT To exit the application and return to the CONTINUE WITH screen Next Step Press SET to set the entered values and proceed to the GRADELINE MARKING screen 4 3 Gradeline Marking Access Press SET from the GRADES screen GRADELINE GRADELINE MARKING 62 MEASURE MARKING P 1D FP10 To s
17. sight points dHz Horizontal angle residual Tol Hz Horizontal angle tolerance dHD BS FS Horizontal distance residual for the backsight and foresight points Tol HD Horizontal distance tolerance dH BS FS Height residual for the backsight and foresight points Tol H Height tolerance Set No Set number Peg Survey FlexLine 17 Peg Survey FlexLine 18 Next step Press OK to proceed to the results screen 2 4 Access TRAVERSE RESULT Peg Survey Results Press OK from the TOLERANCES MET screen TRAVERSE RESULT 172 S 1D 1 x S ID 3 mHz 56 36 25 OK mHD BS 56 465 m To save the data and exit the appli mHBS 0 786 m cation mHD FS 46 632 m EXIT HFS 1 236 m To exit the application and return to the PEG SURVEY settings screen Description of fields Field Description BS FS ID Point ID for backsight and foresight points mHz Average horizontal angle between backsight point and foresight point mHD BS FS Average horizontal distance to backsight and foresight points mH BS FS Average height to backsight and foresight points Sequence Sequence of measurements No of Sets Number of sets Peg Survey FlexLine 19 Peg Survey FlexLine 20 Station Backsight point Foresight point mHz Averaged horizontal angle mHDBS Average horizontal distance to the backsight point mHDFS Average horizontal
18. tart angle and distance measure dHgt 0 552 m poy ments and save the measured dHD 3 123 m values i a Ml DIST Hz 126 56 45 To start distance and angle measure HD 10 253 m ments without saving the measured values PREV To return to the previous screen EXIT To exit the application and return to the GRADES screen Description of fields Field Description PtID Point ID of the measured point dHgt Difference in height between the measured point and the grade point Grades FlexLine 27 Grades FlexLine 28 Gradeline marking step by step Field Description cE If the sign is negative the stake out point is above the meas ured point If the sign is positive the stake out point is below the measured point dHD Difference in horizontal distance between the measured point and the grade point sa If the sign is negative the stake out point is further away than the measured point If the sign is positive the stake out point is closer than the measured point Hz Current horizontal angle HD Measured horizontal distance Step Description 1 Enter a desired point ID PtID 2 Aim at the target point and press MEASURE The height difference dHgt and horizontal distance difference dHD will display 3 Turn the telescope until the height difference dHgt is zero then repeat the measurement Next step Press MEASURE to measure and record data for the current point and pro
19. ter The instrument communication settings must be set to Port RS232 and Baudrate 19200 CS To enable a higher data transfer speed at 19200 bauds the baudrate must be entered manually in the Com Port settings In Mining Editor open a fixpoint file File gt Open Choose Upload Data gt Upload Select a job folder on the instrument to save the data into cE If the selected job already has data all existing data will be over written by the new file being uploaded Mining Editor FlexLine 41 Mining Editor FlexLine 42 Step Description 5 Enter a jobname operator and comments Operator and comments are optional Select a tolerance type and select OK 7 The file uploading will begin and a status bar will indicate the progress Process imported The Mini ng Editor allows import of fixpoint files in ASCII format fixpoint files step by step Step Description Open an ASCII formatted file File gt Open 21x Look in ASCII We mee Size Type 7KB ASC File 10KB GSI File 11KB IDX File 3KB ASC File 8 B OKB ASCFile 5 400_5M ASC OKB ASCFile File name Oper Files of type All Files z Cancel Template lt none gt X Step Description 2 Search and select the ASCII File 3 Open the selected file 4 Follow the wizard onscreen instructions to convert the ASCII file into the
20. tical angle V e Press DIST to measure distance to the peg C The sign for the instrument height is normally negative 3 Press SET to set the point ID and instrument height Peg Survey FlexLine 11 Peg Survey FlexLine 12 Messages The following are important messages or warnings that may appear Messages Description Measures Station or BS point The point ID entered is not available Re enter point ID in the internal memory or it has Step 1 invalid coordinates has no valid coords Next step Press SET to proceed to the TOLERANCE INFO screen TOLERANCE INFO TOLERANCE INFO Survey will be executed acc to the following settings No of Sets 2 Sequence BFFB dHz i 0 00 36 dHD 0 010 m dH 0 010 m OK To continue with Peg Survey Description of fields Field Description No of Sets One set means to measure the backsight point P1 twice and the foresight point P2 twice in both faces Field Description One Set a a Set P1 fe N P2 Ca Two Sets a Set FN 5 TSOX Mining_003 CS The user must complete the number of sets as preset in the tolerance settings A maximum number of 20 sets is supported by the application Sequence Displays the measuring sequence BFFB Backsight Foresight Foresight Backsight BFBF Backsight Foresight Backsight Foresight BBFF Backsight Backsight Foresight Foresight
Download Pdf Manuals
Related Search