before using mobileye c2-170
Contents
1. MOBILEVE Symptom Possible Cause Possible Solution Display Unit is powered OFF Turn on the Display Unit by pressing the ON OFF button Ignition key is switched off Turn ignition key to On position Power cable is unplugged Contact your C2 170 service center Camera Unit is not functioning No signal is tne Power indicator light Contact your C2 170 service center displayed on the back side of the Windshield Mount is OFF The Camera Unit shuts down automatically when Extreme Temperature the ambient temperature is 80 C and will turn on Protection function is again at 75 C activated WARNING The Camera Unit may be very hot Do not touch it until it cools Power indicator light r is ON but Ea GA Display Ynit Contact your C2 170 service center malfunction other signals are showing In case of rain using the wipers in fast speed may solve the problem In all other poor weather conditions wait until bad weather conditions pass Bad weather conditions CAUTION Bad weather conditions and other situations that hamper system visibility also aggravate general driving conditions Drive carefully Low Visibility 1 Clean windshield using wipers indicator is 2 If the source of obstruction is on the inside of ON the windshield carefully remove the detachable Windshield is dirty impaired bottom part of the Windshield Mount clean the visibility relevant area of the windshield and carefully re install the Mount2. e If you set LDW sensitivity to 0 it will disable LDW alerts e If you select 0 the 2 green dots on the left and right sides of the display unit light on constantly indicating Lane Departure Warnings are currently unavailable e To enable LDW alerts make sure the LDW sensitivity level is set to either level 1 or 2 MOBILEVE 8 2 Increase Decrease Volume Option 1 The Increase and Decrease volume buttons let you select between 6 volume levels Press the button to increase volume and the button to decrease volume When you change the volume level of the system the selected volume level will be displayed on the alphanumeric display and a short audio alert will be played to demonstrate the selected volume level Option 2 The Camera Buzzer Unit also has a volume control button that lets you select between six volume levels for audio alerts levels 0 to 5 The LDW and the HMW uses all six levels while the FCW uses only levels 3 to 5 Thus reducing the volume to O disables the LDW and HMW audio alerts but only reduces the intensity of the FCW alert to level 3 Camera Buzzer Unit Showing Volume Level Control Button 8 3 Mute Option 1 Set volume level to 0 Option 2 To Mute press and hold the Minus button of the display for 1 5 seconds Then a long bip occurs To Exit Mute press Option 3 Press the Camera Buzzer unit volume control button repeatedly until no sound is heard Do not
3. the brightness level There are 5 available levels 1 5 15 S77 IDOLE P NOTE The Mobileye C2 170 identifies day and night conditions and automatically switches between Day and Night modes Each mode has its own independent luminance level that can be configured separately The system saves the latest luminance settings for both Day and Night modes until they are changed or until reset to factory defaults 8 1 3 Setting HMW Alert Timing By default the HMW audio alert is sounded when headway is less than 0 6 seconds If you wish to have the audio warning sounded earlier at a greater headway distance or later at a shorter headway the HMW audio alert timing can be changed to a value between 0 1 and 2 5 seconds WARNING Do not change Mobileye C2 170 settings while driving To set HMW audio alerts timing perform the following steps 1 Press the 7 button twice This will change the system mode to HMW Configuration mode This mode will be indicated by a very slow flashing car icon dim inn and dim out and the HW warning level should be displayed by the left digit of seven segments 2 Press the and buttons to increase or decrease timing NOTE Increasing the timing means the HMW audio alert will be sounded while your vehicle is at a greater distance from the vehicle ahead than when the default settings are in effect If you decrease the timing the alert will be activated when
4. your car is relatively close to the vehicle ahead For example setting the HMW audio alert value to 1 2 seconds will cause the system to sound a warning when headway falls to less than 1 2 seconds 16 ST IDOE EZ PE 8 1 4 Setting LDW Alerts Sensitivity LDW alerts are issued by default up to 0 5 seconds before you swerve out of the lane without signaling You can modify LDW alerts by changing LDW sensitivity There are three LDW sensitivity levels 0 1 and 2 Level 2 is the default Reducing sensitivity to level 1 will delay the LDW alerts and setting the system to 0 will turn off LDW alerts To set the LDW sensitivity level perform the following steps 1 Press the button three times This will change the system mode into LDW Sensitivity configuration mode The Right Left Deviation Alert icons will flash at a very slow phase dim inn and dim out and the LDW level should be displayed by the left digit of seven segments Press the and buttons to increase or decrease sensitivity m NOTE Increasing LDW sensitivity means the LDW alerts will be issued when you have not yet verged from the lane either physically or in terms of time to lane crossing Decreasing LDW sensitivity will let you get relatively closer to the lane marking either physically or in terms of time to lane crossing before the alert is activated If you select level 1 the warning line is pushed outwards by 20 cm CAUTIONS
5. 1 4 Troubleshooting 7 8 Mute Mute mode is indicated by a flashing green dot in the lower part of the display unit 7 9 Low Visibility The 2 green dots on the left and right sides of the display unit next to the Left Right Deviation Alert icons will flash constantly Low visibility may be caused by bad weather heavy rain thick fog direct sunlight or some obstructing element condensation or dirt on the windshield etc that is blocking the camera s field of view The Mobileye C2 170 will continue to work during low visibility conditions but may have a shorter range of detection 14 Section 8 CONTROL BUTTONS WARNING Do not adjust Mobileye C2 170 controls while driving S77 MOBILE E Control buttons Mode button Minus button button 8 1 Mode Selectio This button lets you adjust the following functionalities e System ON OFF e Display Unit Brightness Level e Timing of HMW audio alerts e Sensitivity of LDW alerts 8 1 1 System ON OFF To turn OFF the Mobileye C2 170 press and hold the button for 1 5 seconds until the system shuts off To turn ON the Mobileye C2 170 again press any button once WARNING When the Mobileye C2 170 is turned OFF no warnings will be issued 8 1 2 Setting the Brightness Level The Brightness level of the Mobileye C2 170 display unit can be modified by pressing on the button once By pressing the buttons you can decrease or increase
6. Contact your C2 170 service center Cntinously The SeeQ is too hot Turn on the air condition and let the SeeQ unit h cool down flashing Section 10 LICENSE AND WARRANTIES 10 1 Limited Use License a Mobileye hereby grants the original purchaser of the Mobileye C2 Buyer a non exclusive and non transferable license to use the software embedded in Mobileye C2 as supplied by Mobileye as well as the documentation accompanying Mobileye C2 b Buyer shall not a modify adapt alter translate or create derivative works from any software residing in or provided by Mobileye in conjunction with the Mobileye C2 b reverse assemble decompile disassemble or otherwise attempt to derive the source code for such software without written authorization from Mobileye c assign sublicense lease rent loan transfer disclose or otherwise make available such software or d remove proprietary notices on Product or Documentation 10 2 Limited Warranty The Mobileye C2 Limited Warranty the Limited Warranty covers the original purchaser of a Mobileye C2 system installed on the original vehicle for which the system was purchased against defects in material or workmanship for a period of one year from the date of purchase This Limited Warranty is not assignable and shall be voided if Mobileye C2 is transferred to another vehicle Proof of original purchase is required from the warranty holder to obtain limited warranty coverage
7. The sole obligation of Mobileye under this Limited Warranty is to repair or replace at 21 S77 MosicEsE Mobileye s discretion any Mobileye C2 system which is determined by Mobileye to have been defective in materials or workmanship provided by Mobileye Mobileye will not be responsible for conditions arising as a result of installation or use of Mobileye C2 The original purchaser is responsible for all installation charges or incidental expenses associated with replacing Mobileye C2 The following are excluded from warranty coverage a Damage from misuse negligence improper installation or accident b Installation on a vehicle other than the vehicle for which Mobileye C2 was designed c Repair or alteration of Mobileye C2 by any party other than Mobileye 10 3 Warranty Disclaimer This Limited Warranty is the sole and exclusive warranty applicable to the Mobileye C2 Mobileye disclaims all other expressed warranties and all implied warranties of merchantability and fitness for a particular purpose to the fullest extent permitted by applicable law No representative distributor dealer or agent of Mobileye has the authority to make any representation warranty or agreement on behalf of Mobileye with respectto the Mobileye C2 No warranty of any kind or nature is made by Mobileye beyond those expressly stated herein In no event shall Mobileye be liable for any special collateral indirect punitive incidental consequential or
8. exemplary damages in connection with or arising out of the use of the Mobileye C2 10 4 If Warranty Service Is Needed The following procedure is to be followed if a problem arises with the Mobileye C2 1 Contact the dealer if the Mobileye C2 was purchased from distributor 2 Contact Mobileye if the Mobileye C2 was purchased directly from Mobileye All Mobileye C2 must be returned to Mobileye with prepaid freight and return freight A return authorization number is required and may be obtained by contacting our Customer Service Dept at support mobileye com 3 Warranty service requires verification of ownership and date of purchase Please submit the original invoice to establish ownership and date of purchase If acceptable proof of purchase is not available for verification the warranty period is deemed to have begun on the manufacturing date marked on the Mobileye C2 Section 11 TECHNICAL SUPPORT In the event that you encounter a technical problem with Mobileye C2 please refer to the troubleshooting chapter in this User Manual It is intended to assist you in resolving some technical difficulties For additional support please contact your local Mobileye C2 distributor 22 S77 MOBILE E End User Agreement The following form should be signed and returned to your local Mobileye C2 distributor have read and understood the safety instructions and operating manual before using Mobileye C2 including 1 of this user manu
9. flashing indicator is displayed up to 0 5 seconds before a vehicle touches the right lane mark if you have not signaled for duration of 0 7 second 7 3 LDW Availability The 2 green dots on the left and right sides of the display unit next to the Left Right Deviation Alert icons will light on constantly when the Lane Departure Warnings are manually disabled when LDW sensitivity is set to 0 Lane Departure Warnings are unavailable when you drive at speeds below 55 km h 34 mph when the system is muted or if the LDW alerts have been manually disabled 13 P MOBILEVE 7 4 Headway Visual Alert The car icon is displayed when a vehicle is detected ahead of you in the driving lane This icon is colored green or red according to the increasing alert severity see paragraph 6 3 for additional information 7 5 Headway Distance Meter This is a continuous display of the headway distance in seconds from the vehicle ahead that is detected by the Mobileye C2 170 Only values of 2 5 seconds or less are displayed 7 6 System On Indicator This green dot at the bottom part of the display unit is always on when Mobileye C2 170 is operational 7 7 Error System Error Indication a letter E will flash and beside it the error code number This icon indicates that you may have a malfunction in your system When the vehicle is at a standstill turn the switch off and then restart the car If the icon still appears refer to 8
10. h 34 mph ZA Most Es 5 6 When is LDW not Generated An LDW will not issue an audio alert in any of the following circumstances e Lanes are poorly marked or unmarked e You signal before changing lanes e The LDW is disabled sensitivity level is set to zero e You make a sharp turn such as at an exit at a highway interchange e The system has been intentionally muted e You are driving at speeds below 55 km h 34 mph Section 6 HEaDWAY MonitorinG AND Warninc HMW 6 1 What is HMW The Mobileye C2 170 Headway Monitoring and Warning monitors the driving distance from the vehicle in front of you headway and alerts you when the headway is less than a pre defined threshold Headway is measured in seconds and not physical distance The headway is the number of seconds it would take for your vehicle to reach the current position of the vehicle ahead Mobileye C2 170 continuously calculates your headway and displays it numerically on the Display Unit A two second headway in clear weather is usually considered a safe distance 6 2 AHeadway Warning is Generated When A headway warning is initiated when the headway value is less than a pre defined threshold This value is configurable by the user 6 3 HMW Visual Alert The Headway Meter displays the Headway distance in seconds As long as there is a vehicle ahead of you in your lane the Headway Meter s displayed value is continuously updated If no headway value is displa
11. press constantly on button this will turn system OFF 18 S77 MOBILE FE NOTE e The Forward Collision Warning alerts cannot be muted they are critical alerts e Muting will disable the HMW and LDW audio alerts e Mute and OFF conditions are not saved by the system Each time the vehicle is restarted the Mobileye C2 170 is ON and NOT muted 8 4 Urban FCW Sensitivity To change the Virtual Bumper sensitivity Press and hold the button and then press on the button for 1 5 sec A red car icon will start flashing and the numerical display will show Press the to decrease the VB sensitivity or press to increase it 3 Wait 5 sec for change to take effect The VB sensitivity is limited between 0 5 meters and 2 meters The numerical values represent Distance in Meters By Default and Virtual Bumper Sensitivity is set to 1 2 meters Increasing this value will make the VB more sensitive alerts will be sounded earlier Decreasing this value will make the VBS less sensitive alerts will be sounded later e Available only on speed O Section 9 TROUBLESHOOTING The following section provides possible solutions to situations that may occur when using the Mobileye C2 170 Should this section fail in providing the required solution please contact technical support for assistance WARNING Do not perform any maintenance activities on the Mobileye C2 170 while driving 19 S77
12. STI MoB liLlEsE C2 170 Driver Assistance System User Manual S777 Warning MOBILE PE Berore Usina MosiLeve C2 170 Before installing or using the Mobileye C2 carefully read this User Manual and the important safety instructions and warnings it contains LICENSING AND WARRANTY Please read Sections 10 and 11 in this User Manual for licensing and warranty issues Please return the warranty card located at the end of the manual to activate your original purchaser warranty PATENTS The following patents have been issued and assigned to Mobileye US 6 704 621 US 7 113 867 US 7 151 996 US 6 219 444 EP 1236126 EP 1741079 Every effort has been made to ensure the accuracy of all information in this User Manual However Mobileye Technologies Limited makes no expressed or implied warranty or representation based on the enclosed information Mobileye Technologies Limited reserves the rights to alter the equipment specifications and descriptions in this publication without prior notice Any errors or omissions may be reported to Technical Support Mobileye Technologies Limited Email support mobileye com 2007 2009 Mobileye Technologies Limited All rights reserved Reproduction in whole or in part without written permission is prohibited Mobileye Mobileye C2 and the Mobileye logo are registered trademarks of Mobileye Technologies Ltd www mobileye com 2 MoBs icEsE TABLE OF CONTENTS Section 1 6 3 HMW
13. Visual Alert 10 Warnings 4 6 4 HMW Audio Alert 11 1 1 General 4 65 HMW Activation 11 1 2 System Limitations 4 6 6 When are HMW Audio 1 3 Installation and Safety l Warnings Not Generated 11 Instructions 5 i 6 7 Changing the Timing of the Section 2 Headway Audio Alert 12 System Components 5 cection7 2 1 Camera Buzzer Unit 5 Display Unit 13 a Windshield Maimik b 7 1 Left Deviation Alert 13 2 3 Display and Control Unit 6 72 Right Deviation Alert 13 e aarad 73 LDW Availability 13 74 Headway Visual Alert 14 o on Mobileye 62170 7 5 Headway Distance Meter 14 Forward Collision Warning FCW 8 de On Indicator y 4 1 What is FCW B ima 4 2 FCW is Generated When g 72 Mute a i 4 3 FCW Audio Alert 8 7 9 Low Visibility 14 4 4 FCW Activation g section 4 5 FCW Visual Alert g Control Buttons 15 4 6 When is FCW Not Generated 8 Section 5 8 1 Mode Selection 7 15 Lane Departure Warning LDW 9 8 2 Increase Decrease Volume 18 5 1 What is LDW g 8 3 Mute 18 5 2 LDW is Generated When 9 8 4 Urban FCW Sensitivity 19 5 3 LDW Audio Alert 9 Section 9 5 4 LDW Visual Alert 9 Troubleshooting 19 5 5 LDW Activation 9 Section 10 5 6 When is LDW not Generated 10 License and Warranties 21 Section 6 10 1 Limited Use License 21 Headway Monitoring and 10 2 Limited Warranty 21 Warning HMW 10 10 3 Warranty Disclaimer 2 6 1 What is HMW 10 10 4 If Warranty Servi
14. al Warnings and License and Warranties acknowledge that agree to the terms presented in 1 and of this user manual acknowledge that it is the responsibility of the vehicle owner to assure that the drivers have read the Safety Instructions Card and Operating Manual before using this device 1 Owner Company name and address 2 Name of company representative vehicle owner 3 Vehicle details Vehicle type Vehicle make model and year Vehicle registration state and number Vehicle chassis number 4 C2 serial number 5 Date of purchase 6 Dealer name and address Signed Date 23 SIF yy TIIOGILE www mobileye com 2007 2009 Mobileye Technologies Limited All Rights Reserved Mobileye Mobileye C2 and the Mobileye logo are registered trademarks of Mobileye Technologies Ltd
15. bottom part If after restarting the vehicle the Low Visibility indication is still ON contact C2 170 service center ce ea 1 Ventilate the front windshield using the Condensation inside the soir Ae sae a i i vehicle s air conditioning system Windshield Mount 2 Open the windows to clear the condensation 1 Check for obstructions near the Camera Unit Low visibility conditions and remoye them i 2 Low visibility indication should cease when the No audio weather clears alerts are You are driving safely and no dis heard Anestesia dad Keep driving safely System is muted Raise volume level to un mute the system Volume level is too low Raise volume level by pressing the button 20 S77 MOBILE E Symptom Possible Cause Possible Solution 1 Youare driving ga speed 1 This behavior is normal below 35 kevin eim pn 2 Re activate the LDW alerts by setting LDW No LDW 2 LDW function is manually z a y 9 E sensitivity to level 1 or 2 alerts disabled 3 The turn signal on 4 The Hazard signal is on 3 Turn off the turn signal 4 Turn off the hazard signal u n continuously appears in the Headway Meter Missing speed indication Contact your C2 170 service center Restart the system by turning the ignition off and Error R Malfunction during startup then back on If problem persists contact your indicator is ON C2 170 service center Display Unit malfunction
16. ce Is Needed 22 6 2 A Headway Warning is Section 11 Generated When 10 Technical Support 22 S77 S77 MOBILE SE Section 1 WARNINGS 1 1 General Mobileye C2 is a driver assistance system which is intended to alert drivers to certain potentially dangerous situations It does not replace any functions drivers would ordinarily perform in driving a motor vehicle nor does it decrease the need for drivers to stay vigilant and alert in all driving conditions to conform to all safe driving standards and practices and to obey all traffic rules and regulations Mobileye C2 is not an automated driving system and it does not act as a substitute for any aspect of driver vehicle control or safe driving practices Drivers are strongly cautioned not to rely on the Mobileye C2 as a substitution to even the slightest degree for the exercise of due caution in assuring that they are driving safely and avoiding accidents While Mobileye C2 represents a state of the art innovation in machine vision software and other technologies it cannot and does not guarantee 100 accuracy in the detection of vehicles or driving lanes nor in providing warnings of all potential road hazards In addition road weather and other conditions can adversely affect the Mobileye C2 system s recognition and response capabilities Accordingly drivers should not rely on the Mobileye C2 to assure their driving safety but rather should continue to rely on safe drivi
17. ew Mirror Power Indication Light 2 3 Display and Control Unit The Display and Control Unit provides you with e Visual alerts for example visual indication of your current driving distance from the vehicle ahead e System status indications for example a low visibility situation e Control buttons for system control and configuration The Display and Control Unit is attached either to the dashboard or to the front windshield of the vehicle 6 Mos iceEsE Section 3 GETTING STARTED 3 1 Turning on Mobileye C2 170 The system is turned on automatically when the car is started Seconds after starting the car the Mobileye C2 170 display the EyeWatch1 will show the System Ready screen The System Ready screen The displayed elements on the System Ready screen are e a e A green dot on the lower part of System Ready screen indicates that Mobileye C2 170 is ON operative this indication on the lower part of System Ready screen appears whenever the car is at a standstill It will disappear when the car starts moving MosicEsE Section 4 FORWARD COLLISION WARNING FCW 4 1 What is FCW The Forward Collision Warning alerts you to the danger of an impending collision with the vehicle ahead The Mobileye C2 170 calculates the expected Time to Collision TTC with the vehicle in front and when the TTC drops to a dangerous threshold it immediately generates an FCW aler
18. front of you in your lane and drives away a HMW alert is not generated 6 7 Changing the Timing of the Headway Audio Alert The timing of HMW audio warning is set by default to 0 6 seconds You can change this setting to any value between 0 1 and 2 5 seconds To learn how to change the Headway Warning timing refer to paragraph 8 1 3 WARNING e Never configure Mobileye C2 170 while driving e Setting the timing of the headway alert to a low value will activate the alert when vehicles are very close You are always solely responsible for maintaining a safe driving distance from vehicles ahead regardless of Mobileye C2 170 warnings or lack of them 12 S77 MOBILE E Section 7 DISPLAY UNIT A composite illustration showing all C2 170 Display Unit icons is presented in the following figure The Display Unit visual indications HEADWAY VISUAL ALERT CAR ICON LEFT RIGHT DEVIATION ALERT LDW OFF INDICATION LOW VISIBILITY INDICATION FLASH LEFT RIGHT DEVIATION ALERT LDW OFF INDICATION LOW VISIBILITY INDICATION FLASH HEADWAY DISTANCE METER SYSTEM ERROR INDICATION HEADWAY DISTANCE METER SYSTEM ERROR INDICATION ZERO SPEED INDICATION ZERO SPEED INDICATION SYSTEM ON MUTE FLASH 7 1 Left Deviation Alert This flashing indicator is displayed up to 0 5 seconds before your vehicle touches the left lane mark if you have not signaled for duration of 0 7 seconds 7 2 Right Deviation Alert This
19. n described in this User Manual Section 2 SYSTEM COMPONENTS The Mobileye C2 170 includes the following components e Camera Buzzer Unit e Display and Control Unit C2 170 system components Camera Buzzer Unit Display amp Control Unit Camera Buzzer Unit Back View Front View lt 2 1 Camera Buzzer Unit The Camera Buzzer Unit contains the camera the main processor and the warning buzzer of the Mobileye C2 170 system The Camera Buzzer Unit e Identifies lane markings e Identifies vehicles that are driving ahead of you e Processes the video data for potentially dangerous situations e Instructs the system display unit as to which alert to display MosicEsE The Camera Unit is attached to the front windshield by a Windshield Mount a black plastic element that fastens the Camera Unit to the front windshield Please refer to the following illustration IMPORTANT NOTE To prevent possible degradation in system accuracy do not remove or tamper with the Camera Unit or the Windshield Mount 2 2 Windshield Mount The Windshield Mount is used to attach the Camera Unit to the front windshield It also protects the Camera Unit and ensures a clear unobstructed view The Power Indication Light on the back left side of the Windshield Mount following illustration indicates that the Camera Unit is receiving power Windshield Mount and Camera Unit attached to the front windshield Windshield Mount Rear Vi
20. ng practices Drivers should exercise caution in using the Mobileye C2 Display Unit EyeWatch1 Always maintain full concentration on the road at all times including while looking at the Mobileye C2 display 1 2 System Limitations e The Mobileye C2 is intended for paved roads with clear lane markings e The Mobileye C2 only detects fully visible rear ends of vehicles Therefore the detection of crossing oncoming and passing vehicles as well as motorcycles bicycles and pedestrians is not supported e The Mobileye C2 does not guarantee 100 accuracy in the detection of vehicles 4 MoBs ic ese or driving lanes nor in providing warnings of all potential road hazards In addition road weather and other conditions can adversely affect the Mobileye C2 system s recognition and response capabilities e Any conditions that form partial or full blockage of the camera s view will result in reduced or non functionality of Mobileye C2 Always ensure clear camera view 1 3 Installation and Safety Instructions e Mobileye C2 installation must be carried out by an Authorized Mobileye C2 Dealer or Installer e The Mobileye C2 system should not be transferred between vehicles other than by an Authorized Mobileye C2 Dealer or Installer e The Mobileye C2 should only be operated with 12VDC 24VDC power e Do not cover or obstruct the Camera Unit or Mobileye C2 Display and Control Unit e Do not use Mobileye C2 system for any purpose other tha
21. t 4 2 FCW is Generated When An FCW is generated up to 2 7 seconds before possible collision with the vehicle in front 4 3 FCW Audio Alert An FCW audio alert is a series of loud high pitched beeps which effectively draw your attention to the emergency 4 4 FCW Activation The FCW function is always active 4 5 FCW Visual Alert When an FCW is emitted a red flashing car icon is shown on the Display Unit please refer to the following illustration FCW visual alert 4 6 When is FCW Not Generated A FCW is always active unless the system has been turned off Mos iceEsE Section 5 LANE DEPARTURE WARNING LDW 5 1 What is LDW The Mobileye C2 170 provides a Lane Departure Warning LDW to alert you when you are about to unintentionally swerve outside of the lane you are driving in 5 2 LDW is Generated When LDW alerts you when the car begins to swerve from the driving lane The system generates an LDWalert up to 0 5 seconds before the vehicle crosses the lane marking If you use the turn signal prior to moving between lanes an alert is not generated 5 3 LDW Audio Alert The LDW audio alert is emitted for duration of 0 7 seconds 5 4 LDW Visual Alert On the Mobileye C2 170 Display Unit the relevant right or left Lane Departure indicator flashes as shown in the following illustration Left and Right Deviation Alert visual indication 5 5 LDW Activation The LDW is active at speeds above 55 km
22. yed the vehicle in front of you is more than 2 5 seconds away Headway Meter in Seconds 10 SV MOBLE E There are 2 HMW visual alerts shown in the following illustration issued according to the proximity of the two vehicles Notice A green car icon is displayed from the moment the system detects a vehicle in front of your car and as long as the headway remains greater than 0 6 second Warning A red car icon is displayed when headway is less than 0 6 seconds This is dangerous tailgating and the distance between the two cars is perilous HMW visual alerts 6 4 HMW Audio Alert A single chime is sounded to draw your attention to a dangerous headway situation The timing of the warning can be customized by the user Please refer to Section 8 1 3 for customization instructions 6 5 HMW Activation The visual indication is displayed whenever a car traveling in front of your vehicle is detected The audio alert and numerical display are active when you are driving at speeds greater than 30 km h 19 mph 6 6 When are HMW Audio Warnings Not Generated While Headway Monitoring and Warning visual indications cannot be disabled it is possible to mute this function s audio alert HMW will not issue audio warnings when e You drive at speeds below 30 km h 19 mph e The Mobileye C2 170 volume level has been set to 0 or the System has been Muted S77 MosicEsE NOTES When a passing vehicle cuts in
Download Pdf Manuals
Related Search