Home
phoenix audio mt 305 product manual
Contents
1. 1 Phoenix Audio Technologies www phnxaudio com User Manual Please read the instructions in these manual before using the Quattro Please refer to our website www phnxaudio com for more information specifically to our Q amp A section in our Support page For additional help please send a detailed e mail to Support phnxaudio com 2 Phoenix Audio Technologies www phnxaudio com Table of Contents 1 Introduction 3 2 Key Elements 4 3 Key Features 6 4 Control and Panels 8 Primary USB Computer Interface Panel Control Panel Secondary Panel 5 Using the Quattro with Your Computer Connection and Operation 12 6 PSTN Interface Connection and Operation 14 7 VCA Interface Connection and Operation 17 8 Daisy Chain Interface Connection and Operation 20 3 Phoenix Audio Technologies www phnxaudio com 1 Introduction The Quattro is a high quality speakerphone for use in medium to large conference rooms It has an exceptionally large pickup and broadcasting range yet it is small in size
2. o Eliminate the surrounding noise 5 Phoenix Audio Technologies www phnxaudio com o Eliminate the Acoustic Echo o Eliminate the Line Echo when used with PSTN interface o Eliminate the room reverberation o Balance the input pickup level of the different speakers o Balance the output signal level and adjusting it to the type of signal being broadcasted The Result Extended pickup and broadcasting range that can provide high quality communication in a large conference room setup 6 Phoenix Audio Technologies www phnxaudio com 3 Key Features Extended and powerful broadcasting capability As a result of its unique design the Quattro drives up to 25 Watts peak power through its loudspeakers delivering a strong and clear output signal This feature is critical in large room coverage Ganging capability The user can gang unlimited number of units for extended size room coverage Each ganged unit will perform independent audio pickup processing and deliver it to the unit in front of it in the chaining hierarchy The higher hierarchy unit will select the best available audio signal to pass on Each of the ganged units will also transmit the output signal more details in the Daisy Chain Interface chapter Battery operation Each of the interface modules includes a built in rechargeable battery The unit does not have to be connected to the power supply for power The user will be notified when t
3. The Quattro utilizes multiple microphones multiple speakers and a powerful DSP to obtain its performance In its basic configuration the Quattro is designed for PC VoIP communication In addition the Quattro may include an interface module that will communicate directly with your telephone line or other communication devices per your choice The Interface module can be replaced by the factory or by an approved dealer Please send an e mail to support phnxaudio com or call your dealer for details This manual covers instruction for the installation and usage of the Quattro in its basic configuration and with several selected interface modules Specific instructions for other interface modules will be provided separately when you purchase a unit with that specific interface Interface modules that are detailed in this manual include PSTN interface POTS telephones VCA video codec and analog interface Daisy Chain interface 4 Phoenix Audio Technologies www phnxaudio com 2 Key Elements The Quattro utilizes Four microphones Four loudspeakers A powerful Digital Signal Processor that performs the Quattro s sophisticated audio processing This processing includes o Detecting a person speaking o Finding the direction of the person speaking relative to the Quattro o Aiming a directional audio beam towards the person speaking note the Quattro can manage multiple people speaking simultaneously
4. com 2 Using a RCA Y cable split the VC out connect one end to the Quattro right RCA jack and the other end to your speakers This way requires less cables running back and forth from your VC to the Quattro Note that in this configuration the Quattro s internal speaker will work in addition to the external speakers If you wish to disable the internal loudspeakers you can plug a Dummy 3 5mm plug into the 3 5mm jack in the primary interface panel Such dummy plug can be purchased separately you can use any 3 5mm plug for this purpose Dummy Plug Optional Video Codec Quattro Out VC Speakers Out Splitting Connection 20 Phoenix Audio Technologies www phnxaudio com 8 Daisy Chain Interface Connection and Operation Several Quattro units can be chained to provide larger room coverage One of the Quattro s need to be connected to the communication line or computer for that matter Another Quattro will be connected to Quattro number one a third Quattro can be connected to Quattro number two and so on There is practically no limit to the number of Quattro s that can be chained In this chain we refer to the Quattro higher in hierarchy as a Master and the lower in hierarchy as a Slave unit Any Quattro can be a Master since the Master connection is provided with the basic unit and is included on all Quattro s via the primary interface panel In order for a Quattro to become a Slave unit it needs to have a Dai
5. one end and a wider one on the other 2 The Quattro utilizes your telephone for the dialing and ringing functions It is connected directly to your PSTN line through the RJ jack in the wall using a standard telephone cable provided with your phone The telephone is connected to the Quattro using the unique cable supplied with the Quattro Note the unit is supplied with a 6 cable A 20 cable is also available and can be purchase separately 3 If your telephone is currently connected to your telephone line unplug the cable from your telephone leave the wall side connected and plug the loose end to the Quattro the wider jack on the right If your telephone is not connected to the telephone line use a standard telephone cable plug one end to the Quattro wider jack on the right and the other end to your telephone s line wall jack 15 Phoenix Audio Technologies www phnxaudio com 4 Plug the narrow connector of the unique cable to the Quattro left side and the other side to your telephone same jack that you unplugged before and is typically used to connect your telephone to the line 5 You can now use your telephone as before to dial out and get calls in 6 L1 s or L2 position determines whether your telephone is connected to the line or the Quattro refer to the functional drawing on the next page When L1 is active light is on the Quattro is connected when it is inactive light
6. start blinking To un mute push the Power Mute button for less than 3 seconds The light will stop blinking and become steady Notes 1 The unit can be turned off from both On position or Mute In both cases turning off requires pushing and holding the button for about 4 seconds 2 After turning the unit off you should wait a couple of seconds before turning it On again Otherwise the unit may fail to turn On Secondary Interface Panel If your Quattro is equipped with an additional interface module it may have a secondary panel depending on your specific interface Details and description are provided within the instructions of your specific interface module 12 Phoenix Audio Technologies www phnxaudio com 5 Using the Quattro with Your Computer Connection and Operation 1 Plug the USB cable supplied into the Quattro on one end and to your computer on the other end 2 Push the Power Button the unit will turn on blue light is on as an indication The unit will identify itself as Phnx MT301 In most cases the Quattro will become your system s default audio device In some cases depending on the application you are using and on the operating system you are running you ll have to select the Quattro as your Audio Input and Output device Note if your unit does not have a battery if it s not equipped with an interface module or when the unit s battery power level is low the unit
7. 5mm for external speakers or headphones using this jack will disable the Quattro s internal speakers Control Panel The Quattro s control panel has five buttons Power On Off and Mute button in the middle see details of operation below Volume Up and Volume Down to the right Interface control buttons noted as L1 and L2 to the left These two buttons serve different functions depending on the interface module you are using In some cases for 10 Phoenix Audio Technologies www phnxaudio com example in the computer only configuration these buttons have no role and are not functional Operating the L1 and L2 controls please refer to the specific interface module you have on your unit Light Indications Power Mute button light off the unit is off Steady Power Mute light unit is on Blinking Power Mute light the unit is on and the microphones are muted L1 or L2 light is on the button is active For example when using the PSTN interface L1 light on indicates that Line 1 in connected Power On Power Off Mute operation To turn on push the Power Mute button The light will turn on To turn off push the Power Mute button and hold for a few seconds The units will beep four times and turn off in the fifth The light will turn off 11 Phoenix Audio Technologies www phnxaudio com To mute push the Power Mute button for less than 3 seconds The light will
8. ers The red RCA jack on the left is the Quattro s output and it should be connected to your VC system s or sound card s Input The VCA interface has a sensitivity control switch which offers 8 different settings of output signal level This allows the user to tune the Quattro s output level and optimize it to the specific VC or sound card input level specifications The output levels for the different switch settings are detailed in the following table note the orientation of the switches in the diagram represents the way these switches appear when the Quattro is sitting on the table 18 Phoenix Audio Technologies www phnxaudio com Switch Position Output level peak to peak Switch Position Output level peak to peak Line level 3 0v Mic level 0 5v Line level 1 5v Mic level 0 25v Line level 0 75v Mic level 0 125v Line level 0 375v Mic level 0 0675v In order to use the VCA interface with a digital phone s headset jack you need the proper cable two RCA to RJ11 There are two types of wiring depending on the type of telephone you are using These cables are available for purchase separately Using external speakers If you wish to use your VC s speakers you can either 1 Connect the VC out to the right RCA jack and connect your speakers to the 3 5mm external speakers jack on the Quattro s primary panel Or 19 Phoenix Audio Technologies www phnxaudio
9. he battery power is low The unit can be recharged through the USB or with AC DC wall mount power supply supplied with the interface module Three Way communication When using the Quattro with both the computer through the USB interface and an additional communication device through the additional interface module like the PSTN line the Quattro mixes the incoming and outgoing signals so that the three partners the Quattro user the telephone communication and the computer communication are full participants in the conference 7 Phoenix Audio Technologies www phnxaudio com In addition to being convenient in many instances this feature allows to record the telephone conferencing and also playback audio files into the telephone lines 8 Phoenix Audio Technologies www phnxaudio com 4 Control and Panels The Quattro has A Primary USB interface panel A Simple control panel and A secondary interface panel optional Primary USB Computer Interface Panel The Quattro has a primary USB panel that includes three jacks USB on the right for computer communication 9 Phoenix Audio Technologies www phnxaudio com Cascading DIN6 in the middle for chaining additional Quattro units This connector can also be used to connect an external microphone The chained Quattro unit must have a Daisy Chain interface Please refer to the Daisy Chain Interface chapter for more details 3
10. is off your telephone is connected 7 Please follow these steps to conduct a conference call a Dial out pick up your telephone s handset and dial the number you want to call At any time after dialing push L1 or L2 if you dialed using line 2 to transfer the call to your Quattro The Quattro is now connected to the line and your PSTN Connection Diagram 16 Phoenix Audio Technologies www phnxaudio com telephone is disconnected As such the telephone is currently not functional and you cannot utilize its dial pad unless you switch the call back to your telephone see C below b Accepting a call when your telephone rings you can push L1 or L2 if the call is coming from line 2 to accept the call on the Quattro No need to pickup the handset c Switching back to your telephone Pickup the telephone s handset and push L1 or L2 if the call is on line 2 The Quattro will be disconnected form the line and you can use your telephone ordinarily L1 Telephone Line PSTN Functional Diagram 17 Phoenix Audio Technologies www phnxaudio com 7 VCA Interface Connection and Operation The VCA interface is an Analog In Analog out interface It can be utilized to connect the Quattro to a Video Set top Codec a computer s sound card or a digital phone headset jack The black RCA jack on the right should be connected to your VC system s or sound card s output the signal that goes to the loudspeak
11. microphones searching and tracking the best possible audio signal The diagram below illustrates the process 22 Phoenix Audio Technologies www phnxaudio com PSTN Line Thank you for purchasing the Quattro For more information please refer to our Website www phnxaudio com or call 516 829 2920
12. sy Chain interface Connecting a Slave unit to a Master is done using a unique cable supplied with the Daisy Chain interface PSTN or Other Network Connection Unique Cable 21 Phoenix Audio Technologies www phnxaudio com Powering the Slave unit the Slave unit has a battery and it does not need any extra power supply If the battery on the Slave unit runs low the unit will turn Off its loudspeakers The unit s microphone and audio processing will still run powered by the Master through the connecting cable Remember if the Slave unit s battery is low it is still powered and operational it will just shut off its loudspeakers to preserve power The Master unit can supply enough power to operate the Slave unit s microphones and processor but not its loudspeakers You can connect the Slave unit to an external power supply using an AC DC converter which is supplied with the Daisy Chain unit Microphone Pickup Performance the Slave unit is not just a simple satellite microphone The unit runs the same audio processes as a stand alone unit including the person speaking detection direction finding and tracking The Slave unit will transfer its processed audio to the Master unit which will weigh its quality against its own pickup quality If the talker was closer to the Slave and was picked up better by the Slave the Master will select the Slave s signal as the preferred one With two units connected you have in actuality eight
13. will turn on as soon as you plug it into the USB port and you will not have to push the Power button to turn On You will still be able to turn the unit Off and On again as you wish 3 You can control the unit s pickup level microphone using your computer s audio controls You can control the unit s playback speaker level using either the computer s audio controls or the unit s Volume Up Volume Down controls 13 Phoenix Audio Technologies www phnxaudio com Note when working with both a VoIP application and an additional communication interface it is recommended that you set the speakers level using your computer s volume controls first Then you can use the unit s volume controls to set the output level of both interfaces to a comfortable level The reason is that your computer controls only the level of signal coming out of your computer and not of the other interface while the unit s volume controls affect both 4 Push the power button with a short push to toggle between Microphone On and Mute When muted the light will blink 5 Push and hold for 4 seconds to turn the unit off the unit will beep four times and turn off on the fifth 14 Phoenix Audio Technologies www phnxaudio com 6 PSTN Interface Connection and Operation 1 The PSTN interface panel has two RJ jacks one narrower than the other A unique telephone cable is supplied with the unit This cable has a narrow RJ connector on
Download Pdf Manuals
Related Search
Related Contents
Windows Xp ー安全上の注意 ReleaseNotes DG 12.2.2. - 3DEXCITE Software Services Untitled - Idemasport Kawasaki Ninja 250R service manual (eng) Westinghouse 52-Inch Specification Sheet User Manual - CIE LIBRO DE PRODUCCIÓN Copyright © All rights reserved.
Failed to retrieve file