BOX USER MANUAL - p3connectors.com
Contents
1. aime BOX USER MANUAL Thank you for purchasing our Powersafe sequential Coupling Unit The unit controls the connection sequence of incoming out going cable connections The sequence ensures that the Earth connection is made first and disconnected last FMLB First Mate Last Break To connect cables to the unit 1 With key Included turn the Earth lock clockwise Fig 1 The Earth cover will pop open 2 Ralse the Earth cover fully open 3 Take the Earth cable end connector not included and plug into the Earth position The Powersafe connectors are mechanically keyed to prevent connection errors So it is not possible to plug any other connector other than and Earth keyed connector into this position 4 To mate the connectors align the arrow on the mating connector with the green circle on the Powersafe unit front panel Push the connector fully into the box until it stops and then turn clockwise 5 The Neutral cover will now pop open 6 Raise the Neutral cover to the fully open position Note when covers are raised the previous connection cannot be disconnected without first closing the cover for example when the Neutral cover is raised the Earth connector cannot be removed 7 Repeat steps 3 6 until all 5 connectors E N L1 L2 amp L3 are connected 8 When the L3 connector is mated and turned fully clockwise to the locked position Take the key lock and turn the L3 lock clockwise Fig 2 Turning this l2. A B Cireut complete when lock is open NC Micro Switch rated voltage 250VAC Micro Switch rated current 3A For Further Information or Assistance please contact our sales office Web Site www p3connectors com Telephone 44 0 1592 775995 Email Sales Mp3comnectore com Postal Address Phase IK Limited Unit 14 Fife Business Centre Southfield Indu ZRU United Kingdom te Glenrothes Fife KYS
3. n 1 2U rack mounting Height 88mm Length 483mm Depth 130mm Option 2 Panel mounting Height 108mm Length 483mm Depth 130mm For this option add 108 to part number Maximum Rated Voltage to Earth 2KVac Current Rating Up to 800A Rear Terminals M12 x 25 threaded studs Micro Switch rating 250VAC 3A Part Code Panel Source Box Green Black Red Yellow Blue phase Coding PSS UK Panel Source Box Green Blue Brown Black Grey phase Coding PS5 E Panel Source Box Green Black Red White Blue phase Coding PS5 A Panel Drain Box Green Black Red Yellow Blue phase Coding PD5 UK Panel Drain Box Green Blue Brown Black Grey phase Coding PD5 E Panel Drain Box Green Black Red White Blue phase Coding PDS A Micro Switch Connector Accessory MSPC 3P Micro Switch Lead Assembly Connector assembled with 1 5 meters of 3 core x MSCA 3P 1mm jacketed cable Unlocking Tool Spare UN PSB Source Earth Dummy Plug Allows box to be used in 4 wire configuration EDP PSBS without Earth Position Drain Earth Dummy Plug Allows box to be used in 4 wire configuration EDP PSBD without Earth Position Ca BOX Micro Switch Pin Configuration COMMON To wire for switch normally Open use A C Circuit complete when lock is engaged To wire for switch normally closed use
4. ock does two things a It locks the L3 connector in place to prevent accidental disconnection under load and prevents further access to the unit b It switches an integral micro switch which can be used as a signal path for electrical protection device A 3 pin connector plug is available which will plug onto the 3 pin connector on the rear of the unit to allow for connection of such devices Fig 3 To disconnect cables from the Unit The disconnect sequence is reversed Therefore the connectors have to be removed from Right to Left starting with the L3 connector 9 Turn L3 key lock anticlockwise to release the L3 connector 10 Now turn the L3 connector fully anticlockwise and pull out of the port 11 Push the cover down note the cover will not fully close at this point however with the cover raised it will not be possible to remove the next connector 12 Now turn the L2 connector fully anticlockwise and unplug Note the L3 cover will automatically fully close during this action 13 Once all connectors are removed turn the Earth key lock anticlockwise This locks the Earth cover preventing access to the unit BOX Fig 1 The Earth lock prevents unauthorised use of the unit Final lock prevents removal of connectors from unit and activates integral micro switch Locking Tool Connector on rear panel for connection of micro switch cable Micro switch lead connectol Technical Data Overall Dimensions Optio
Download Pdf Manuals
Related Search