Home

Manual

1. BEIJING EPSOLAR TECHNOLOGY CO LTD EPEVER LandStar EPLI Series Solar Charge Controller with built in LED Driver Thank you for selecting the LandStar EPLI series solar charge controller It combines the solar charge controller and LED constant current driver into one unit which is ideal for solar LED Lighting especially for the application for LED lamp which requires dimmer function The control parameter can be programmed by Mobile APP Remote Meter and SPP 02 with infrared IR function 1 Safety Information e Read all of the instructions and cautions in the manual before beginning installation e There are no user serviceable parts inside the controller Do not disassemble or attempt to repair it e Install external fuses breakers as required e Disconnect the solar module and fuse breakers near to battery before installing or adjusting the controller e Power connections must remain tight to avoid excessive heating from a loose connection e Only charge the batteries that comply with the parameters of controller e Battery connection may be wired to one battery or a bank of batteries 2 Overview The advanced pulse width modulation charging methods enables the system charging and discharging management to obtain the most radical optimization Make the system cost reduce and increase the system flexibility The features are listed below e 12 24VDC automatic identify or user defined working voltage e Without any key para
2. Micro IAM Mobile and APP APP software can be downloaded from the website of http www epsolarpv com MISA SPP 02 Mobile amp APP Figure 3 Setting Ways NOTE Please refer to the user manual of handheld device 6 Load Set 1 Manual Mode 2 Light ON OFF default Uy ay wy WU ly sly sdy Night Time 3 Light ON Timer Light ON Timer1 2 r r R ini time1 time2 time3 ime KEZ vlsi vty SLA NEA vl wea z lee Light ON Timer2 Remaini time1 time2 gig time3 usa vlvinty wt a i z L e 4 Time Control Control the load on off time through setting real time clock NOTE In the mode of Light ON OFF and Light ON Timer the Load is turned on after 10Min delay BEIJING EPSOLAR TECHNOLOGY CO LTD Tel 86 10 82894112 82894962 Website www epsolarpv com www epever com 7 Protection e PV Reverse Polarity Fully protection against PV reverse polarity no damage to the controller will result Correct the miswire to resume normal operation e Battery Reverse Polarity Fully protection against battery reverse polarity no damage to the controller will result Correct the miswire to resume normal operation e Battery Over Voltage When the battery voltage reaches to the set point of Over Voltage Disconnect Voltage the controller will stop charging the battery to protect the battery from being over charged to break down e Battery Over Discharge When the battery voltage reaches to t
3. e or turn on the breaker during Tel 86 10 82894112 82894962 Website www epsolarpv com www epever com the installation When disconnecting the system the order will be reserved 2 After power on the controller check the battery LED indicator on the controller it will be on solid green Otherwise please refer to chapter 8 3 Connecting a fuse in series through battery positive in the circuit and the battery circuit fuse must be 1 25 to 2 times to the rated current The installed distance is within 150mm 4 LED Indicators Indicator_ Color Status Instruction PV connection normal but Green On Solid low voltage irradiance from PV no charging Slowly Flashing 1Hz In charging peg Fast e 4Hz PV reverse polarity No PV volt ht time Green ORF age nig We or PV connection problem On Solid Slowly Flashing 1Hz Fast a 4Hz Over voltage Orange On Solid sd Solid Under voltage eee On Solid Over discharged Red Slowly Flashing 1Hz Battery Overheating ee ieee green battery red ee ieee E 5 Setting Operation inglgator System voltage error There are three methods that it can realize Cirever tawai controller work mode and parameters through IR E function 1 Infrared Remote Meter MT55I 2 Super Parameter Programmer SPP 02 This method can realize one key setting operation which is suitable for bulk quantity products setting or applied in the projects 3 Ir Android
4. he set point of Low Voltage Disconnect Voltage the controller will stop discharging the battery to protect the battery from being over discharged e Battery Overheating The controller detect the environment temperature through the external temperature sensor If the environment temperature exceeds 65 C the controller will automatically start the overheating protection to stop working and recover below 50 C e Load Short Circuit Load will be switched off when load short circuit 24 times rated current happens Controller will automatically attempt to reconnect load for 5 times If short circuit protection still exist after controller s 5 times attempts user have to clear short circuit then disconnect and restart the controller or wait for one night day cycle night time gt 3 hours e Damaged Local Temperature Sensor If the temperature sensor short circuited or damaged the controller will be charging or discharging at the default temperature 25 C to prevent the battery damaged from overcharging or over discharged e High Voltage Transients PV is protected against small high voltage surge In lightning prone areas additional external suppression is recommended 8 Troubleshooting Faults Possible reasons Troubleshooting Charging LED indicator off during daytime when sunshine falls on PV modules properly Win OV can etni u Measure battery voltage with No LED indicator l P multi meter Min 9V can start up the the control
5. it Voltage e Boost Reconnect Charging voltage gt Low Voltage Disconnect Voltage Any changes without prior notice Version number V2 2
6. ler controller Disconnect the solar array and Battery LED mare measure the battery voltage whether is indicator green Fast te j Flashing too high Change the controller Change the battery LED Battery When the battery voltage is restored to or above setpoint low voltage over discharged reconnect voltage the load work PV Confirm that PV and battery wire array disconnection connections are correct and tight Battery over voltage Battery indicator red The controller will automatically sto Battery Status LED working When the HE A below 50 C the controller will resume to work Check whether the battery voltage match with the controller working voltage Please change to a suitable battery or reset the working voltage indicator red flashing All the LED indicator flashing battery red indicator flashing Powering on normally the load is off The dimming function is invalid Parameter settings fail Battery Overheating System voltage error The connecting wires are error or virtual connection Load mode is Check the connecting cables 2 Check the load mode and parameter The voltage of LED light source is not in the output voltage range of controller Check the connecting cables and LED light source wrong 3 The controller does not match with the LED light 4 Output short circuit The controller does not match with the LED light source This product is a step up cu
7. meter setting via Mobile APP Remoter Meter and SPP 02 with IR function e Maximum output efficiency of 96 e Dimming function e Digital precision constant current control and the control accuracy are less than 30mA e With functions of current power calculation and real time energy statistics recording it is convenient for users to view charging and discharging energy of each day month year and total value e Adopting temperature compensation and correcting the charging and discharging parameters automatically improving the battery lifetime e Widely used automatic recognize day night e Fully encapsulated PCB IP68 protection e Aluminum housing e Support firmware upgrade Product Features and Wiring CEPEVER Mounting hole Aluminum housing LS102460EPLI PWM Solar Charge Controller Charging Status LED indicator amp LED Driver i B CE RoHS Battery Status LED indicator Temperature Sensor PV Positive and Negative Wires Battery Positive and Negative Wires Load Positive and Negative Wires Infrared Receiver Module Infrared LED ORORO ROROE OROROORO Figure 1 Product Feature i MTSSI Q ne o 2a 9 SPP 02 mf mf Mobile amp APP amon E is rai Euse D Fuse i BEE iw mE i DV or 24V Figure 2 Wiring 1 Connect components to the charge controller in the sequence as shown above and pay much attention to the and Please don t insert the fus
8. rrent control If input voltage is lower than the rated voltage it is not working Replace the LED light 2 Reduce system rated voltage grade and replace the product model For example 24V system change to 12V system and replace the corresponding controller Infrared i n See handheld the user device manual communication error 9 Technical Specifications Oo o lm O LS101240EPLI LS102460EPLI LS2024100EPLI Marinak SyS 12VDC 12 24VDC Auto 12 24VDC Auto voltage current voltage Battery input 9 16V 9 30V voltage range Max output power 30W 12V 60W 24V 50W 12V 100W 24V Max output Current Output voltage Max Battery Voltage 2V 60V range voltage Maximum output 96 efficienc Output current lt 30mA control accurac Battery Type Sealed Default Gel Flooded User Self consumption Charge Circuit Voltage Drop med Temperature compensation coefficient Communication distance of IR Communication angle of IR Working environment temperature Enclosure Overall dimension 8mV C 2V lt 6m 15 90 C400 C IP68 1 5m 72h 107x68x20mm 108 5x88x25 6 mm Mounting dimension 100mm 100 5mm Mounting hole size PV BAT 14AWG 2 5mm PV BAT 12AWG 4 0mm Power cable LOAD 18AWG 1 0mm LOAD 18AWG 1 0mm Net weight 0 23kg 0 39kg Battery Voltage Parameters parameters is in 12V system at 25 C please use X 2 in 24V system Over Voltage Disconnect 16 0V 16 0V 16 0V 9 17V Voltage Charging Limit Vol
9. tage 15 0V 15 0V 15 0V 9 17V Over VOIE REconnEc 15 0V 15 0V 15 0V 9 17V Voltage Equalize Charging Voltage 146v 14 8V 9 17V Boost Charging Voltage 14 4V 14 2V 14 6V 9 17V Float Charging Voltage 13 8V 13 8V 13 8V 9 17V Boost Reconnect Charging a Voltage 13 2V 13 2V 13 2V 9 17V Low Voltage Reconnect 126V 126V 126V 9 17V Voltage l l l Under Voltage Warning 122V 122V 122V 9 17V Reconnect Voltage Under Voltage Warning 42 0V 12 0V 12 0V 9 17V Voltage l l Low Voltage Disconnect 11 1V 111V 111V 9 17V Voltage i i l Discharging Limit Voltage 10 6V 10 6V 10 6V 9 17V Equalize Duration 20min 120min 0 180min NOTE 1 The default battery type is Sealed For Sealed Gel Flooded battery type the voltage point is fixed unable to modify it The adjusting range of equalize duration is 0 to180min and boost duration is 10 to180min 2 User type is the user defined battery type The default value is the same as sealed type When modify it please follow the below logistic relation a Over Voltage Disconnect Voltage gt Charging Limit Voltage 2Equalize Charging Voltage 2Boost Charging Voltage 2 Float Charging Voltage gt Boost Reconnect Charging Voltage b Over Voltage Disconnect Voltage gt Over Voltage Reconnect Voltage c Low Voltage Reconnect Voltage gt Low Voltage Disconnect Voltage 2 Discharging Limit Voltage d Under Voltage Warning Reconnect Voltage gt Under Voltage Warning Voltage 2 Discharging Lim

Manual

Contents

Download Pdf Manuals

Related Search

Related Contents