LBI-39056 - EDACS C3 MAESTRO CONSOLE SYSTEM EDITOR
Contents
1. Console Name 8 character console name or alias Names less that 8 characters are space padded MAESTRO Console ID ID used by the console for normal radio communication via CIM channels and 2 The valid ID range is 1 16382 800 Call Director ID ID used by the console for call director patch via CIM channel 4 This must be a unique ID from the unit console ID space 0 or 16383 are valid for non CD patch consoles The valid ID range is 0 16383 0 Startup Setup The setup number that the console will start up with The valid setup range is 1 10 1 A number corresponding to a language text file that the console will read into memory at startup 0 Language 0 English 4 Spanish 8 Hungarian 1 French 5 Swedish 9 Polish 2 German 6 Norwegian 10 Dutch 3 Italian 7 Finnish 11 Portuguese l Seb TROY The PC bus hardware interrupt IRQ used by the Console Logic Board normally referred to as simply the Logic Board to interrupt the PC The valid IRQ numbers are 7 10 11 12 CLBs identified 500 0006 000 manufactured previous to 1993 can only use IRQ7 7 Speaker Config This is actually the number of speakers in the console system Valid numbers are and 2 for single PA Board systems and 1 4 for dual PA Board systems See Tower PA Boards below 2 Tower PA Boards The number of Audio Tower PA Boards installed Valid numbers are 1 or 2 Two 2 boards are requir2. About This Menu Displays a window containing brief information about the parameters that can be edited General information Edit Config Database Displays the Configuration Data form Editing numeric and yes no parameters used by the application at startup Section 8 1 Disable Keyboard Keys Displays the Disable Keys form Disabling certain keys on the dispatch keyboard Section 8 2 Edit Site Database Displays the Site Data form Editing the text of the site names Section 8 3 Edit Screen Colors Displays the Screen Colors form Changing the colors assigned to various fields and areas of the Maestro screen Section 8 4 Edit DAC Values Displays the Edit DAC Values control panel Changing the RGB values of the individual colors used by the application Section 8 5 Read Special Config File Prompts the user for a configuration filename Reading a special configuration file in for editing other than the default CONFIG DAT Section 8 6 Save Changes to Disk Prompts user to save changes to disk Saving the configuration changes to a file The default is CONFIG DAT Section 8 7 Restore Initial Database Restores setup database to the values before editing began Restoring the memory image of the database to its values previous to editing Quit Changes and Return and Return to Main Menu Returns user to Main Men
3. Erasing all startup modules from the current setup Clear Patch Simulselects Prompts user to confirm clearing Section 7 3 Erasing all patches and simulselects from the current setup Copy Setup Prompts user for source and destination setups Section 7 4 Copying the contents of one setup to another setup or to all other setups Edit Page Database Displays Page Data form for current setup Section 7 5 Editing the test of the page names displayed in the page window Edit User Profile Data Displays User Profile Data screen for current setup Section 7 6 Editing of numeric and yes no parameters in the user profile of the current setup Save Changes to Disk Prompts user to save changes to disk Saving the setup changes to the SETUPS DAT file Restore Initial Database Restores setup database to the Restoring the memory image of the database save values before editing began to its values previous to editing Quit Changes and Return and Return to Main Menu Esc Returns user to Main Menu Select other main editing functions or return to MS DOS 7 1 SELECT SETUP NUMBER When Select Setup Number is selected from the Edit Setups Profiles Menu the Setup Number Window is displayed This number must be set to the number of the setup that is to be edited and saved It must be set before editing begins It remains
4. lt 7 oe Moves the highlight bar to the next record Moves the cursor to the beginning of the next field OEN Moves the highlight bar to the first record Moves the cursor to the beginning of the current field Moves the highlight bar to the last record Moves the cursor to the end of the current field Moves the highlight bar to the first record on the Up current page or to the first record on the Does nothing AN previous page if already at the top of the current page Moves the highlight bar to the last record on the f current page or to the last record on the next Does Nothing page if already at the bottom of the current page 4 Executes the current highlighted function on the Completes the entry on the current field suier Function Menu N S7 Esc Exits the main edit Exits the form CN 0 3 EDITING A RECORD When Edit has been selected from the Function Menu the left hand record edit form shown in Figure 7 is displayed If the selected record exists the current data is displayed in the form otherwise the data displayed is undefined The user should enter the required data to complete the form If the type is C conventional the right hand form will be displayed after the left hand form is complete Table 6 shows the validation checks made on the entered data Since the data is not rigidly checked the user should use care when entering the data After the form is complete t
5. that will be copied to the destination setup the destination setup will be overwritten with data from the source For single copies the user should enter two different numbers separated by a space each in the range 1 10 For example entering 2 8 will copy setup 2 to setup 8 If it is desired to copy the source to all setups the destination should be 99 For example entering 7 99 will copy setup 1 to all setups 2 10 Only source numeric data not the source setup title is copied to the destination s This preserves the titles of all destinations Figure 14 Copy Setup Source Destination Window 7 5 EDIT PAGE DATABASE When Edit Page Database is selected from the Edit Setups Profiles Menu the Page Data form is displayed See Figure 15 The page numbers 1 8 on the form are static they cannot be changed The user can modify the page names stored in the current setup by using the form navigation keys and text editing keys Page names are limited to eight 8 alphanumeric characters NOTE Maestro application module numbering format of a letter A H followed by a 2 digit number cannot be changed 18 LBI 39056 z G z oo yuy AU AUNE Figure 15 Page Data Form 7 6 EDIT USER PROFILE DATA When Edit User Profile Data is selected from the Edit Setups Profiles Menu the User Profile Data form and top bottom information line is displayed See Figure 16 All
6. 33 LBI 39056 13 TECHNICAL INFORMATION 13 1 SYSTEM REQUIREMENTS The Editor program requires the following minimum configuration e IBM PC AT computer or compatible e MS DOS 3 3 or later e One floppy disk drive and a hard disk e VGA display e 640K RAM 13 2 OPERATING SYSTEM Unlike the Maestro application that uses a proprietary multi tasking operating system Editor is a MS DOS application Screen displays are done by writing directly to video RAM bypassing the BIOS and MS DOS Keyboard I O is done at the BIOS level 13 3 DISPLAY MODE The user may notice that the Editor characters appear different than the characters seen in MS DOS Editor operates in color 80 column by 28 row text mode The normal 25 row 16 x 9 pixel character set is changed to a 14 x 9 pixel EGA character set This provides an extra three 3 display rows since shorter characters are used The display is returned to 80 x 25 text mode when the program terminates Due to the color choices used in the program Editor displays may not be easily readable on monochrome displays There is no way to modify the colors to rectify this situation If Print Screen is used to print the Editor screens certain PC BIOS versions may only output the first 25 rows of the display 34 14 INDEX Audio Tower ppp 23 Auxiliary I O Msg Dela yotini anne 24 VIEW 32 Baud Rate 6 24 Call Director pe 23 24 CLB a cise etn a eel the 23 Compatibility
7. 63 Reserved 8 4 2 Keys The following keys are used to navigate around the window and adjust the labels attributes Jel Navigation from label to label The small white arrow points to the selected label for which the foreground background or blink can be changed al Jat Increments the foreground color to the next color After color 15 the color reverts back to color zero KA ZN 27 LBI 39056 Increments the background color to the next color After color 7 the color reverts back to color Zero Toggles the blink attribute for the foreground background colors SA ka AN Restores the selected label to the colors previous to the beginning of the editing Restores all labels to the colors previous to the beginning of the editing S k ZN NOTE Recommendation Make a backup copy of the CONFIG DAT file before changing colors or save the changed color configuration with a different file name Section 8 7 8 5 EDIT DAC VALUES When Edit DAC Values is selected the Edit DACs screen shown in Figure 21 is displayed When the screen is first displayed the screen colors will change dramatically They will be adjusted to those of the Maestro screen color palette as defined in CONFIG DAT Colors are displayed as they appear on the Maestro screen during normal operations BGS FEE EEE HTO T PgUp PgDn Select Color Prompt T J Select RGB lt Adjust level Restore Values
8. Debug Messages Development mode debug messages are displayed N Y Messages displayed N No messages Rt Unpriv Emer Route unprivileged emergencies on to supervisor console An unprivileged emergency is one that occurs on an unprivileged and unprogrammed group Does not apply to non supervisors N Y Emergencies on unprivileged and unprogrammed groups are declared on the console N Emergencies on unprogrammed groups are declared on the console Confirmed Call Enables group confirmed call i e confirmed channel request from console N Y Group confirmed call requests N Normal call requests Force Tones Beeps error confirmation emergency etc tones are forced to the select speaker or headset even if the tone is related to an unselected entity N Y Tones to select speaker or headset N Tones follow entity 8 EDIT CONFIGURATION When Edit Configuration is selected from the Main Menu the Edit Configuration Menu shown in Figure 17 is displayed EDIT CONFIGURATION Edit Config Database Disable Keyboard Keys Edit Site Database Edit Screen Colors Edit DAC Values Read Special Config File Save Changes to Disk Restore Initial Database Quit Changes and Return Return to Main Menu Esc Figure 17 Edit Configuration Menu 21 LBI 39056 TABLE 10 EDIT MENU CONFIGURATION SELECTIONS MENU ITEM ACTION USE
9. current file and edit memory parameters The top line shows the name of the file being edited the file size and the date and time the file was last saved The filename will always be ENTITY DAT The file size will vary depending on the number of entities in the file A reminder about the help key is located at the right end of the line The bottom line shows the current number of each type of entity FUNCTION TOP INFORMATION LINE FILE NAME MENU FILESIZE LAST SAVED ENTITY DAT 32128 bytes 02 28 94 12 34 56 Edit Delete Sort Write File Erase DB Pvt All Pvt Privilege All Pvlg Find Name Find Next Find ID Hex Mode Quit NUM IDI TYPE HGROUP HSITE PRVLG PVT NAME_ 0 1234 2 IL FA Y SIMURINSE IE il 1240 2o Y Y BROWN P 2 TASS ZL JONES P 3 A 1 i i ai 274 0 S PATROL 0 E PATROL FIRE HIGHLIGHTED LINE ENTITY RECORD EDIT AREA 289 J al LINE CONS gul CONS VZ SUPR CON xxxnbnaoanoanta KKK KK KK KE 4 5 6 7 8 2 9 0 aL alt 1234 Groups 85 Phones 0 Consoles 6 Figure 6 Entity Editor Screen 12 LBI 39056 6 1 2 Function Menu The Function Menu is located on the second and third lines of the screen It contains the fourteen 14 editing functions that can be executed A function can be selected by two methods e Use the left and right arrow keys to move the highlighted bar over the desired function and press lt Enter gt e Use the hot key selection m
10. erased Toggles the private status for the highlighted entity Y indicates private status is set and a blank Pvt at i indicates private is off All Pvt Toggles the private status for all units and groups Toggles the privilege for the highlighted entity Y indicates that the privilege is set blank indicates Privilege Pe 2 the privilege is off All Pvlg Toggles the privilege for all entities Finds the first record whose name alias matches the search string The search string is entered in a small window when this function is selected Up to 8 characters can be entered The search is not case sensitive Find Name Finds the next match s of the search string This function can be repeated to find all entities whose Find Next name matches the search string Find ID Finds the first record that matches the search number Hex Mode Toggles the display of IDs between decimal and hexadecimal The display mode is hexadecimal when a check appears next to the word Hex Quit Returns the user to the Main Menu 13 LBI 39056 6 2 KEYS Table 5 identifies the keys and key actions used to navigate around the entity editor or entity record form TABLE 5 ENTITY EDITOR AND ENTITY RECORD SELECTIONS KEY MAIN EDIT ACTION FORM ACTION Moves the highlight bar to the previous record Moves the cursor to the beginning of the previous field e
11. is 0 255 150 Supervisor Supervisor console and supervisor privileges N Y Supervisor N Normal operator 24 Hour Time 12 24 time display mode Y Y 24 hour military time N 12 hour time G nsel Labels Caller aliases labels displayed on unselected calls Y Y All callers displayed N Only selected callers Numeric Labels LID GID etc numbers used instead of aliases in module displays N Y Display IDs N Display aliases Numeric Volume Numeric module volume level 0 32 used instead of volume bar N Y Numeric value N Volume bar Auto Alarm Off Audible alarms automatically reset by emergency clear Y Y Alarm reset when emergency is cleared N Alarm must be manually reset even if emergency is clear Continued LBI 39056 TABLE 9 USER PROFILE DATA PARAMETERS Continued PARAMETER DESCRIPTION AND VALID VALUES Beep w Error Beeps error tones when keyboard errors occur or warning message banners are displayed Y Beep with keyboard error or banner N No beeps Rst Before Clr Reset Emergency Before Clear Alarm reset acknowledge is required before lt EMER CLR gt key will clear emergency N Y Alarm must be reset first N lt EMER CLR gt works all the time Disp Failsoft Failsoft trunking status indicator is displayed Y Y Display indicator N No display
12. name beginning with a letter and names with leading spaces will come before any name beginning with a number or letter When Write File is selected from the Function Menu directly after record editing the user will see the warning message shown in Figure 9 It is not necessary to sort the database before saving However if the database is sorted previous to saving blank records are eliminated and the entity records are easier to view WARNING Database is not sorted Figure 9 Database Not Sorted Warning Message 7 EDIT SETUPS PROFILES When Edit Setups Profiles is selected from the Main Menu the Edit Setups Profiles Menu is displayed See Figure 10 ETUPS PROFILE Select Setup Number Clear Startup Modules Clear Patch Simulselects Copy Setup Edit Page Database Edit User Profile Data Save Changes to Disk Restore Initial Database Quit Changes and Return Return to Main Menu Esc Figure 10 Edit Setups Profiles Menu 16 LBI 39056 TABLE 8 EDIT SETUPS PROFILES MENU SELECTIONS MENU ITEM ACTION USE About This Menu Displays a window containing brief information about the parameters that can be edited General information Select Setup Number Prompts user for setup number Section 7 1 Setting the current setup number for all setup editing Clear Startup Modules Prompts user to confirm clearing Section 7 2
13. save to disk of module programming changes add modify delete when lt MODL MODFY gt is used N Y Immediate save to disk N On demand with lt F10 gt Mod Ignores DV Mode Modules can ignore the digital clear voice mode of incoming calls i e they will not follow the call mode N Y Modules ignore call mode N Modules follow call mode Default to DV Mode All units and groups may default to private digital when programmed Even if module is saved as clear voice it will be programmed as private when the application starts up All module add modify operation follow the setting N Y All units and groups are programmed as private N All units and groups are added as clear voice or follow their saved mode at startup 24 LBI 39056 8 2 DISABLE KEYBOARD KEYS When Disable Keyboard Keys is selected from the Edit Configuration menu the Disable Keys form shown in Figure 19 is displayed DISABLE ELECT gt E gt Volume Keys MODFY gt FUNCS gt FUNCS gt lt lt M lt lt lt SE lt lt lt F lt lt D He E H rt Tone Keys All Patch Keys All Simulselect Keys All Telephone Icom Keys An A AA A Aar A A AA AAA A A A A Figure 19 Disable Keys Form A key or group of keys is disabled by setting the Yes No field to Y The key fun
14. until any key is pressed This copyright screen includes Ericsson GE copyright information and the program s version number If password control is not enabled the Editor Main Menu is displayed after the copyright screen 4 2 PASSWORD Editor is protected from unauthorized use by means of a password Password control can be enabled or disabled If enabled a small window will be displayed after the copyright screen This window will prompt the user for a password The password will not be echoed to the screen however the cursor will move to indicate user input The password is not case sensitive and the backspace key may be used for editing The password can be changed or disabled but only if the current password is known There is no password when Editor is installed on a new system It is up to the user to set a password if desired 4 3 EXITING To exit Editor from any menu or form press lt Esc gt repeatedly until the screen is cleared and the MS DOS prompt is visible again If data is not saved before exiting with multiple lt Esc gt presses the data in memory will be lost and the file data will remain unchanged 4 4 HELP ___ Help is available by pressing lt F1 gt Help is context sensitive In other words help is displayed for the selected field when lt F1 gt is pressed Help appears as a single line of text at the bottom of the screen It temporarily overwrites any text on the bottom row Help text is erased and the pre
15. 3 Emergency module background l 35 Not used 4 Picked module border l 36 Name list title ID 5 Unpicked module border l 37 Name list normal text 6 Selected module background I 38 Name list highlight bar 7 Module name foreground l 39 Not used 8 CALL and caller foreground l 40 Not used 9 XMT I 41 Not used 10 BUSY foreground l 42 Not used 11 PBY foreground l 43 Not used 12 PRIV foreground l 44 Debug window 13 Conventional indicators foreground 45 Debug window 14 Phone intercom ind foreground l 46 Prompt line 15 Reserved l 47 Warning error message banner 16 Volume bar l 48 System message banner 17 MUTE foreground l 49 Cross mute banner area 18 Sign on screen company info l 50 Telephone or intercom call banner 19 Sign on screen title version l 51 Emergency status indicator banner 20 Normal page l 52 Not used 21 Active call page l 53 Clock 22 Current page l 54 Pl S1 indicators 23 Active emergency page l 55 P2 S2 indicators 24 Status window attribute 1 l 56 P3 S3 indicators 25 Status window attribute 2 l 57 P4 S4 indicators 26 Status window attribute 3 l 58 P5 indicator 27 Status window attribute 4 l 59 Low VU 28 Normal call history l 60 Medium VU 29 Emergency call history l 61 High VU 30 Emergency declare call history l 62 No VU VU background 31 Call history detail
16. ELECTION FORM ITEM OR ACTION OR CHANGE ACTION TO TAKE Purge entity database Edit Entity Database Erase DB n a Change sidetone levels Edit Setups Profiles Edit User Profile Opr Sidetone or Data Sup Sidetone Change page names Edit Setups Profiles Edit Page Database Edit any page name field Purge old patches and Edit Setups Profiles grear Been n a simulselects PERC CES Set serial port for 19 2k baud oar an connection normally used for Edit Configuration Edit Config Database 19 2K Baud Y hardwired connection to CIM Set serial port for 9600 baud ae ae connection normally used for Edit Configuration Edit Config Database 19 2K Baud N modem connection to CIM Change foreign language Edit Configuration Edit Config Database Language Assign new foreground and background colors to a screen field or area Edit Configuration Edit Screen Colors Select field and change foreground and background colors an existing screen color Change RGB components hue of Edit Configuration Edit DAC Values Select color and move sliders Change the password Change Password none Enter current and new passwords in prompt windows NOTE All data should be saved to disk after the changes are made 3 SCREEN AND KEYBOARD BASICS This section will familiarize the user with screen display techniques and the use of keys in the Editor program 3 1 KEYBOARD The E
17. ERICSSON 3 LBI 39056 Mobile Communications EDACS C3 MAESTRO CONSOLE SYSTEM EDITOR PROGRAM User s Manual LBI 39056 5 3 SCREEN AND KEYBOARD BASICG cccssssssssssssssssssessscsssessscsssessscssssssesssessscsssessscsssssscsssessseees 7 2 CLEAR STARTUP MODULEG sccssssssssssssssssrssesssesssesssessscssscssscsssesssessscssscssscssscssscssscssoess 17 7 3 CLEAR PATCH SIMULSELECTB sssssssssssscsssssessscsssessscsssessscssscssscssscssscssscssscssscsssesoers LO 7 6 EDIT USER PROFILE DATA ccsssssscssscssssscsssesssesssesssessscssscssscssscssscsssesssessssssessscssscsseres LD 8 1 EDIT CONFIG DATABAGE cssssssssssscssssssersscssscsssesssesssessscssscssscssscssscsssesssessscssscssscssessscses 22 8 2 DISABLE KEYBOARD KEYS E 25 8 6 READ SPECIAL CONFIG FIL see 30 8 7 SAVE CHANGES TO DISK csssssssssssssscsserssessscssscssscssscsssessscssscssscssscsssessscssscssscssscssesssetes J0 i Copyright February 1994 Ericsson GE Mobile Communications Inc LBI 39056 TABLE OF CONTENTS Continued Page 9 EDIT LANGUAGE FILES wis cccdecseisctscscsectesteiecossesscecssevsdesecesccusucevsgesscasesesescescesdcesacssocesscceceacdevecssacesaceos 31 10 VIEW On 32 11 CHANGE PASSWORD es ETES 33 12 COMPATIBILITY scciseccisecsscssdeceecescvsvscsuecesosescescdesvessecesescensessssecc
18. Quit Examples in this window Error Msg 28 Figure 21 Edit DACs Screen LBI 39056 8 5 1 About Colors There are sixteen 16 colors available for use on the Maestro screen The colors will be referenced by a number from 0 15 where 0 is usually black and 15 is usually white Colors 0 7 may be used as foreground and background colors while colors 8 15 can only be used as foreground colors Each color is made up of three component colors Red Green and Blue RGB Each component color can be adjusted to have a level intensity of 0 63 Up to 262 144 possible color hues are possible by mixing various levels of the component colors The three component colors red green blue cannot be changed S The simple S box to the left represents a single character cell on the Maestro screen The area around the letter is the background color gray and the foreground color is black A VGA compatible PC contains sixteen Digital to Analog Converters DACs that convert the digital 0 63 RGB levels stored in registers to analog voltages that are fed to the color display This part of the Editor changes the RGB levels stored in those registers When all RGB levels are 0 the color is black When they are all at maximum 63 the color is white When the RGB levels are nearly equal shades of gray from black to white are possible as the levels increase 8 5 2 Palette Window The palette window is the top window on the Edit DACs
19. al Configuration File Filename Input Window 8 7 SAVE CHANGES TO DISK The user is prompted for a filename when Save Changes to Disk is selected The default file name is CONFIG DAT but the user can edit the name to a new file Saving the data to a new file name allows multiple screen color combinations by using the different files 30 LBI 39056 NOTE The only file name that the Maestro application will read is CONFIG DAT If more than one color configuration is needed save the changes to CONFIG 000 CONFIG 001 etc then use the MS DOS RENAME REN command to rename the desired file to CONFIG DAT 9 EDIT LANGUAGE FILES The Edit Language File menu is shown in Figure 24 The user should select one of the languages Other should be selected for a language not on the menu EDIT LANGUAGE French German Italian Spanish Swedish Norwegian Finnish Hungarian Polish Dutch Portuguese Other Main Menu Figure 24 Edit Language Files Menu When the language is selected the large text string edit window is displayed with the first twenty text strings displayed The first string is a null string and it will appear empty Do not edit this string A string is selected by moving the highlighted bars over the desired string and pressing lt Enter gt This will open up a one line form with the current string contents Editing is done within this window Press lt Enter gt
20. am do not contain all of the features described in this manual In contrast future versions of the Editor program may contain additional features that are not described in this manual See Section 12 in this manual for additional program version details Users of the Editor program should be familiar with EDACS particularly in regards to the Console Electronics Controller CEC or the Integrated Multisite and Console Controller IMC Digital Audio Switches and supporting equipment such as the CEC IMC Manager Users must understand that the CEC IMC Manager should be the central point of databasing and configuration for all C3 Maestro consoles connected to the CEC IMC Changes made locally at a console by the Editor program can override those previously made by the CEC IMC Manager Correspondingly changes made at the CEC IMC Manager can also override changes previously made at a C3 Maestro console This document shall not attempt to explain in detail the implications or workings of system parameters that can be set with the Editor but how they can be set and in most cases valid parameter values For example the user will be shown how to enable Confirmed Call but not what Confirmed Call is or what will happen if it is enabled TABLE 1 CHARACTER STYLES AND SYMBOLS USED IN THIS MANUAL EXAMPLE DESCRIPTION Display Courier type is used to simulate information that appears on the computer screen CONFIG DAT Bold CAPITAL letters ar
21. ccccccccees 22 TABLE 11 EDIT CONFIGURATION DATABASE PARAMETER ccccccsssscccscssccccccceees 23 TABLE 12 DISABLE KEYBOARD KEYS SELECTIONS 00 cccsssssscccccsscscscccccceccccecsssees 25 TABLE 13 SCREEN COLOR DESCRIPTIONS cccccccccsssscccsccsccccscsscccsccccccccsscccccssssesseeeee 27 TABLE 14 VIEW AUX I O FIELDS cccccccscsccccccccccccscccccccccccccsccccccscccscccesccccccccceseccccssseeee 33 NOTE Information in this document is subject to change without notice CREDITS IBM is a registered trademark of International Business Machines Corporation PC AT is a trademark of International Business Machines Corporation MS DOS is a registered trademark of Microsoft Corporation LBI 39056 This page intentionally left blank LBI 39056 1 INTRODUCTION This user s manual describes the use ofthe C3 Maestro Editor program which is distributed with C3 Maestro application software package 344A3922Gxx The Editor program provides a user interface to the C3 Maestro support files in the absence of the CEC IMC Manager MOM PC It is a non essential utility program because except for a few configuration items all of the same configuration and database tasks can be performed by the CEC IMC Manager This manual was developed in accordance with Editor program Version 3 10 which is included with software package 344A3922G10 Earlier versions of the Editor progr
22. ctions normally when the field is set to N The corresponding PC keyboard key if any is also disabled TABLE 12 DISABLE KEYBOARD KEYS SELECTIONS KEY DESCRIPTION lt Key Title gt Disables the specific key labeled with the title in brackets lt MODULE SELECT gt Disables lt MODULE SELECT gt but does not disable lt Alt lt MODULE SELECT gt function for Call Director patch Module Volume Keys Disables both the Volume Up and Down keys for modules but does not affect lt Alt gt lt Volume gt used for headset sidetone adjustment All Alert Tone Keys Disables all three alert tone keys as a group All Patch Keys Disables lt P1 gt lt P5 gt lt P1 TX gt lt P5 TX gt and lt PATCH VIEW gt as a group All Simulselect Keys Disables lt S1 gt lt S4 gt and lt SIMUL VIEW gt as a group All Telephone Icom Keys Disables lt CALL RLSE gt lt CALL HOLD gt lt CALL ANSR gt lt PHONE ICOM TX gt and lt CALL FUNCS gt as a group 25 LBI 39056 8 3 EDIT SITE DATABASE When Edit Site Database is selected the Site Data form shown in Figure 20 is displayed NAME SITE 1 CAND 800 MVR SIMULCST VOTER SITE 7 1 2 3 4 3 6 7 8 Figure 20 Site Data Form The site numbers 1 32 on the form are static The user can add delete or modify site names by using t
23. data remains current N Any other The cursor moves to the first field for further editing No new data has been accepted but the new data remains in temporary storage NOTE The data in some fields will be automatically right justified when lt Enter gt is pressed after entering numeric data that is less than the width of the field This will also occur when numeric fields are passed over using the arrow keys This right justification is normal the field data is unaffected LBI 39056 3 5 PROMPTS A prompt is a small one line form which prompts the user to enter a number or a yes no response For yes no prompts a yes or no default answer is displayed at the cursor position If lt Enter gt is pressed the default answer is accepted as the answer For example if the default answer is Y yes and the user wishes to answer yes to the prompt question only lt Enter gt must be pressed A prompt with a No default answer is shown in Figure 3 Confirm E E startup modules N Figure 3 Typical Prompt 4 RUNNING EDITOR This section will instruct the user in the basics of starting and ending the Editor program It will also show how to get on line help during the operation of the program 4 1 STARTING Start Editor from the MS DOS prompt by typing EDITOR followed by lt Enter gt The current directory must be C CONSOLE The Editor s copyright screen will be displayed for five seconds or
24. data remains unchanged and the cursor moves to the beginning of the next field Exits the form The following keys are used for form editing Backspace A gt D Completes user input on the current field and moves the cursor to the beginning of the next field Deletes the character to the left of the cursor but does not affect the character under the cursor Deletes the character under the cursor and shifts the text to the right of the cursor to the left The cursor does not move When the cursor is at the end of a field and the user attempts to enter more characters than the width of the field a beep will sound and the cursor will not move any farther to the right A form can be completed in three ways editing the last field on the form e moving across all fields with arrow keys or by pressing lt Enter gt repeatedly e pressing lt Esc gt anywhere on the form When a form is completed the following message is displayed The data is not accepted at this point Press ENT ER to accept ESC to abort changes any other key to Re edit At this point the data can be accepted existing data is overwritten exited without saving changes or edited again These keys are defined as follows _ 1 The data on the form is accepted and stored in memory Previous data is Enter overwritten LOOS S7 The form is exited All new data entered on the form is ignored and the previous SS
25. ditor program uses the standard PC keyboard exclusively Both white and gray navigation keys can be used for cursor positioning functions The custom Maestro keyboard is never used during the operation of the Editor 3 2 WINDOWS A window is a rectangular area on the screen that appears temporarily for the purpose of viewing information or entering data When the user acknowledges the information or completes a data entry task the window is erased and the LBI 39056 previous screen contents under the window are restored The Editor uses the drop shadow technique to make the windows appear to float above the screen WINDOW SCREEN DROP SHADOW Figure 1 Window 3 3 MENUS A window in which various functions and commands are organized is a menu Figure 2 shows a typical menu A highlighted bar is used to mark one of the menu items This bar moves up and down the list of items by using the navigation keys Most items have a single highlighted letter used for instant or hot key selection A menu item may select a function or another menu A menu item can be selected by two methods e Use the up and down arrow keys or lt Page Up gt and lt Page Down gt to move the highlighted bar over the desired item and press lt Enter gt Press the letter key that matches the highlighted letter in each item title This key is known as a hot key The lt Enter gt key does not need to be pressed after pressing a h
26. e used for the names of files used with Editor This style is also used to indicate MS DOS commands COPY for example Words in italics are data that the user must supply by typing from the keyboard Italics may also User mpi be used occasionally in the text for emphasis Words inside angle brackets lt gt identify certain keys on the keyboard that the user must press lt Enter gt a to perform a specific function Examples include lt Enter gt and lt F1 gt S7 Page This example symbol represents a key on the standard PC keyboard that the user must press to Up make a selection This example shows the lt Page Up gt key LONS 2 QUICK REFERENCE This section is primarily intended to aid users who are already familiar with the Editor program Users who are new to the Editor should proceed to Section 3 to learn Editor operating details Table 2 lists in the ACTION OR CHANGE column the more common configurable items that are unique to the Editor program It highlights the more common items that cannot be changed at the CEC IMC Manager It is a non inclusive list for all unique configurable items The table also shows the menu s to select to advance to the field or window to make the changes LBI 39056 TABLE 2 CONFIGURABLE ITEMS UNIQUE TO THE EDITOR PROGRAM Non Inclusive List MAIN MENU SELECTION NEXT MENU S
27. ed for call director patch or extra unselect speakers 1 CTIS Hang Time Reserved for future use 0 Continued 23 LBI 39056 EDIT CONFIGURATION DATABASE PARAMETERS Continued TABLE 11 PARAMETER DESCRIPTION AND VALID VALUES System Msg The delay in seconds that a system message queued denied etc will be displayed before Delay being erased Valid times are 30 seconds 2 AuxI O Msg The delay in seconds that an Auxiliary I O input message will be displayed before being erased Delay Valid times are 30 seconds 3 Serial data rate selection for console to CEC IMC communications COM1 The setting 19 2K Baud should be N for V 32 data modems 19 200 baud is the preferred hardwired data rate Y Y 19 200 baud N 9600 baud Alt Keyboard File Allows the console to use the data file ALTKBD DAT with an alternate keyboard table instead of the built in keyboard table N Y Use ALTKBD DAT table N Use default table Call Director Status of call director connection N Y Call Director connected N No Call Director I Call Alias Enables the I Call numeric alias entry feature As an alternative to name list selection or LID entry of an unprogrammed I Call a numeric alias of up to 8 digits can be entered after lt ICALL SEL gt N Y Enabled lt gt is enabled N disabled Mod Prog Quick Save Enables the immediate
28. esseveadesvcaseascoeseedegeesscese sesso cesdesoessbcsseses 33 13 TECHNICAL INFORMATION ccccccsssssssssscccccccccccscssssscccccccecccssccccccceecccsscsccccccssccssssccscccsscceeecees 34 13 1 SYSTEM REQUIREMENTS ee 34 13 2 OPERATING SY STEM so cccccisccsiscdescccscssesssscceecdes lscdstescdsecdeaccosctessscecdescssecesscseesdossssecesssoeseesscosnses 34 13 3 DISPLAY MODE c esi 34 aE E E DI DD EET E NE SEAE E EIEE E E SE E E E O EREA E ERSE 35 TABLES TABLE 1 CHARACTER STYLES AND SYMBOLS USED IN THIS MANUAL ccccseees 5 TABLE 2 CONFIGURABLE ITEMS UNIQUE TO THE EDITOR PROGRAM 000 6 TABLE 3 MAIN MENU SELECT ION G ccccccsssssssssscccccccscssssscccccccccsssscscccccccccssssscccceceecssscsees 11 TABLE 4 FUNCTION MENU SELECT IONG cccccssssccsscsccccscsccccsccscccccccccccccccsccccscsecccccees 13 TABLE 5 ENTITY EDITOR AND ENTITY RECORD SELECTIONS vs 14 TABLE 6 ENTITY RECORD FORMS VALIDATION CHECK ccccccccssssscccccsccccccscees 15 TABLE 7 SORTING METHOD MENU SELECTIONS sccccccccsssssssssscccccccccsscssceccccecccscscees 16 TABLE 8 EDIT SETUPS PROFILES MENU SELECT IONG ccccccccsssscccssssccccccccsccccscees 17 TABLE 9 USER PROFILE DATA PARAMETER cccccsccccsscsscccscsscccccscccccccccccccscsesseceeee 20 TABLE 10 EDIT MENU CONFIGURATION SELECTION G ccccccccsssscccscscccccccs
29. ethod by pressing the letter key that matches the highlighted letter in each function title The following table shows a brief description of each function The hot key letter is shown is bold type TABLE 4 FUNCTION MENU SELECTIONS MENU ITEM USE A Edits the highlighted entity record A small window containing an information form is displayed when Edit the function is selected A secondary form window is displayed for conventional only information If the record is blank the data from the form is added as a new entity See Section 6 3 Delete Deletes the highlighted entity record from memory Deleting is immediate there is no prompt for j confirmation Accidentally deleted records are not permanently deleted until the file is saved to disk Sorts the entity records according to the sorting method selected when this function is selected The ort sorting can be done by ID number Name alias or Home Group Records are sorted by type unit group conv phone console first and then by the selected method See Section 6 4 Writes saves the file image in memory to a disk file named ENTITY DAT The previous entity data is written to a file named ENTITY OLD If the file has not been sorted a warning message will be displayed It is not necessary to sort the file before writing it to disk Write File Erase DB Erases all records in the file image A confirmation window is displayed before the data is
30. he data will be displayed in the main edit area and the highlighted bar will move down to the next record 14 LBI 39056 Figure 7 Entity Record Forms TABLE 6 ENTITY RECORD FORMS VALIDATION CHECKS PARAMETER RANGE CHECK ID 1 16382 Type None Home Group 0 2047 Home Site 0 32 Privilege Y or N Private y or N Name Max 8 characters Channel 1 99 Max RX TX 1 8 Zero is a valid home group for a group conventional or phone 6 4 SORTING RECORDS The Sorting Method Menu is displayed when Sort is selected from the Function menu See Figure 8 SORTING METHOD Name Home Group Figure 8 Sorting Method Menu 15 LBI 39056 TABLE 7 SORTING METHOD MENU SELECTIONS SORTING METHOD RESULTS ID Number Records are sorted by type and then numerically by ID number Name Records are sorted by type and then alphabetically by name Home Group Records are sorted by type numerically by home group and then numerically by ID During the sorting process blank records are eliminated and the file size of the potential new file is recalculated Consoles are sorted separately from units even though they reside in the same ID space The alphabetic sorting is done by ASCII value therefore a name beginning with a number will come before any
31. he form navigation keys and text editing keys A site name can be deleted by making the name field blank with spaces or deleting all characters 8 4 EDIT SCREEN COLORS The Screen Colors window is displayed when Edit Screen Colors is selected It contains 64 labels representing a screen area field or indicator These color settings are stored in CONFIG DAT This menu selection should always be preceded by a selection of Edit DAC Values see below in order to set the colors to actual Maestro hues 8 4 1 Color Descriptions Table 13 describes the use of each of the 64 colors used in the Maestro Where foreground is explicitly mentioned the color is used against a background color defined elsewhere For these special foregrounds their backgrounds on this screen must remain black for proper mixing with their actual Maestro backgrounds Where background is explicitly mentioned the foreground color on this screen should be black for proper mixing 26 LBI 39056 TABLE 13 SCREEN COLOR DESCRIPTIONS NO DESCRIPTION NO DESCRIPTION 0 Main background l 32 Menu title 1 Page status call history headers l 1 33 Menu normal text 2 Normal module background l 34 Menu highlight bar
32. of the user profile data parameters shown in Table 9 can be set at the CEC IMC Manager except the setup Title parameter Subsequent CEC IMC Manager profile updates will override any Editor changes Default values are shown in square brackets SETUPS DAT TITLE MUTE MUTE LABEL MAX C TONE OPR S SUP S 17920 bytes 02 28 94 16 50 22 USER PROFILE DATA Operator Setup DEFAULT VOL DEFAULT SPKR EMERG VOL VOL DELAY DELAY BLANK DELAY MIN ALRM VOL NFM DEL OFFSET IDETONE IDETONE 16 2 16 0 30 0 0 16 0 5 SUPERVISOR 24 HOUR TIME UNSEL LABELS NUMERIC LABELS NUMERIC VOLUME AUTO ALARM OFF BEEP W ERROR RST BEFORE CLR DISP FAILSOFT DEBUG MESSAGES RT UNPRIV EMER CONFIRMED CALL 2 2 Z K 22K SZEKK EZ Patches 0 FORCE TONES Figure 16 User Profile Data Screen 19 LBI 39056 TABLE 9 USER PROFILE DATA PARAMETERS PARAMETER DESCRIPTION AND VALID VALUES Title Setup Title This is the current setup s title displayed on the Maestro Change Setup notecard It can contain up to 31 printable ASCII characters Operator Setup x Default Vol Default unselect volume This is the volume at which all newly programmed entities are set to Valid range is 0 32 16 Default Spkr Default unselect speaker This is the unselect speaker to which all newly added entities are set Valid numbers are 2 for a single PA Boa
33. onent color level Restores all colors to their component values previous to beginning color editing 8 5 5 Accepting Changes When the user has completed color editing the Edit DACs screen can be exiting by pressing lt Q gt or lt Esc gt As shown in Figure 22 the user will then be prompted with a window asking if the original palette colors should be restored Restore original palette colors N Figure 22 Restore Original Palette Colors Confirmation Window If further foreground background color changes for screen areas or indicators are to be made continue with the default answer No However if the color editing is complete the user may answer Yes if it is desired toreturn to the normal Editor screen colors The color changes are permanent when the Save Changes to Disk option is selected from the Edit Configuration menu 8 6 READ SPECIAL CONFIG FILE When Read Special Config File is selected the user is prompted for a file name The default file name is CONFIG DAT but the user can edit the name to a new file The file must already exist before it is read The normal MS DOS file naming conventions are expected Typical names would be CONFIG 000 CONFIG 001 CONFIG NEW etc If the user is going to create a modified configuration file based on CONFIG DAT use the default for reading but save it using a different filename after the changes have been made Filename CONFIG DAT Figure 23 Read Speci
34. ors in CONFIG DAT Section 8 Edit Language Files Displays the Edit Language File Menu Editing English or foreign language text strings displayed by the console application Sec 9 View Aux I O Displays the Auxiliary I O screen View the contents of AUXIO DAT Sec 10 Change Password Prompts user for current and new passwords Change the current password to a new password Section 11 About Editor Displays a window describing the Editor program General information Exit to DOS Terminates program returns user to MS DOS prompt Returns to MS DOS prompt LBI 39056 When one of the Edit or View selections is made a file related to that selection will be opened If the file is missing or cannot be opened for some reason the window shown in Figure 5 will be displayed XXXXXXXX can be ENTITY CONFIG PHONE AUXIO or a language name If the file is missing it can be copied from the Maestro installation disk or from another console XXXXXXXX DAT open error Press any key to continue Figure 5 File Open Error Message 6 EDIT ENTITY DATABASE 6 1 EDITOR SCREEN The entity database editing screen is composed of four main sections the top and bottom Information Lines the Function Menu and the main editing area The screen layout is shown in Figure 6 6 1 1 Information Lines The top and bottom lines of the screen display
35. ot key EDITOR MAIN MI Highlighted Selection Setups Profiles Configuration Highlighted Edit Language Files Letter for j Aux I O Hot Key nge Password Selection About Editor Instant Exit to DOS 1 Execution Figure 2 Typical Menu LBI 39056 The following keys are used to navigate around a menu E Jel _ f F Q D LSS AN _ eve ES W _7 Je AEN 3 4 FORMS Moves the highlighted bar to the previous item Moves the highlighted bar to the next item Moves the highlighted bar to the first item Moves the highlighted bar to the last item Selects the item under the highlighted bar Returns to the previous menu or exits to MS DOS from the Main Menu A window that requires or accepts user input is a form A form is made up of fields in which the user enters data A field may require as little as a single character for example Y for yes or several characters The following keys are used to navigate around a form or field Jel CN f N Sif End Moves the cursor to the beginning of the previous field Moves the cursor to the beginning of the next field Moves the cursor to the beginning of the current field Moves the cursor to the end of the current field Moves the cursor to the beginning of the next field m gt D ESC LBI 39056 If pressed without entering data the current field
36. pp 33 Configuration 5 6 19 22 Entities Editing et 14 Brasin banuan prai 6 13 Savine nng nonta oies 13 SOPMNE reer 15 EXE eie aea 10 Files Config Names pp 30 j DEKO REE 12 Form S h e n R A 8 Configuration Data 22 Entity Record pp 14 Sit Datas eann p 26 User Profile pt 19 Helpies aias 10 IDs Call Dirfector pp 23 CONSE nee aane 23 Keyboard 6 Keys Color Editing pp 27 DAC Editing eee 29 Disabling nisaire 25 Entity Editor et 14 OTDR 8 Menus cosicci stteiedt tein sitentiacds 7 Language 31 Startups osise 6 23 Menus a tiie an eatin 7 Configuratign cesses 21 ERICSSON B Ericsson GE Mobile Communications Inc Mountain View Road Lynchburg Virginia 24502 LBI 39056 Language Files 31 Ma 11 Setups Profiles pe 16 Modems 0 24 MS DOS senner s 10 34 Password ee 10 11 33 Prompts sn nnsa seors 10 Quick Reference pp 5 Running Editor eee 10 Screen Colors 00006 6 26 34 Changing c ck iti 26 DACS cucaniekite den 28 Sidetone Levels 008 6 20 SUES ci cvsiceedeesedigeeesidiedestecsedenierves 26 Starti NET erneer eieae 10 System Requirements 34 User Profiles Editing se 19 Windows Ne 6 Printed in U S A 35
37. r Board register bit number that corresponds to input or output ACT lt Alt gt Key that activates output DEACT MOM Momentary output output is deactivated when key is released lt Key gt Alternate action output lt Alt gt key that deactivates output MESSAGE Up to 25 character message that is displayed when input is triggered 11 CHANGE PASSWORD This function allows a qualified user to change the program password The user must know the current password in order to change it When the function is selected the user is prompted for the current password If the password is entered correctly the user is then prompted for a new password The new password may be up to fifteen 15 characters consisting of letters and numbers Password characters are not displayed on the form as they are entered only the movement of the cursor is seen Password control can be disabled by pressing lt Enter gt when prompted for the new password This sets the password to a null string which is interpreted by the program as no password Current Password Figure 27 Change Password Windows 12 COMPATIBILITY Editor Version 3 x is compatible with C3 Maestro Version 3 x and later support DAT files Use of Editor with Version 2 x support files will result in erroneous data displays and corrupted files if they are saved Conversely the use of previous versions of Editor with Version 3 x support files will have the same results
38. rd system or 2 4 for a dual PA Board system 2 Emer Vol Emergency volume Valid range is 0 32 16 A Mute volume This is the volume to which a module will be set when muted Valid range is 0 32 Mute Vol 0 All Mute Delay This is the delay in seconds that all mute will remain active until it is Mute Delay automatically canceled Valid range is 0 60 30 Label Delay Call and Caller label delay This is the delay or hang time in seconds that these fields will remain active after a call has actually dropped Valid range is 0 10 0 Blank Delay Screen blanking delay This is the delay in minutes that the screen will remain on without key or call activity before going blank 0 disables the feature Valid range is 0 30 0 Min Alrm Vol Minimum alarm volume See CEC IMC documentation for details Valid range is 0 32 16 Max Cnfm Del Maximum confirmed call delay in seconds Reserved for future use 0 Tone Offset Confirmation and system tone offset in dBm See CEC IMC documentation for details Valid range is 0 20 which translates to 0 to 20 dBm 5 Opr Sidetone Operator headset sidetone level setting for digital pot on the Audio Matrix Board Applies to AMB Rev A or later Valid range is 0 255 150 Sup Sidetone Supervisor headset sidetone level setting for digital pot on the Audio Matrix Board Applies to AMB Rev A or later Valid range
39. screen It consists of sixteen blocks of colors the palette an arrow pointing to the blocks three horizontal RBG slide controls the sliders and an arrow pointing to the sliders To adjust any color the user selects the color then selects the component color and then adjusts the level of the component color The level of any or all of the three component colors determines the hue of the selected color As the selected slider is moved the digital value is displayed at the right edge of the slider The portions of the screen that use the selected color change along with the changes made by the sliders The sliders wrap around when a slider moves past its maximum value it returns to zero to continue forward instead of remaining at the maximum position 8 5 3 Samples Window This window has _actine controls It displays the sample color changes as they will appear on the Maestro screen Several common screen areas fields and indicators are shown in the samples window 8 5 4 Keys The following keys are used to control the color selection from the palette pick the component color for adjustment and to adjust the level of the component color __ Sal Selects previous color moves arrow left from palette Selects next color moves arrow right from palette Selects B blue then G green then R red Selects R red then G green then B blue 29 LBI 39056 Decreases component color level Increases comp
40. the current setup number until it is changed or the Edit Setups Profiles Menu is exited The default number is 1 Setup number 7 2 CLEAR STARTUP MODULES Figure 11 Select Setup Number Window When Clear Startup Modules is selected from the Edit Setups Profiles Menu the erase confirmation window is displayed If confirmed as YES all startup modules stored in the current setup will be erased Startup modules are those that are programmed when the Maestro application starts up and establishes a link with the CEC IMC If lt Enter gt is pressed the default answer of No is accepted and nothing is erased 17 LBI 39056 Confirm E E startup modules N Figure 12 Clear Startup Modules Erase Confirmation Window 7 3 CLEAR PATCH SIMULSELECTS When Clear Patch Simulselects is selected from the Edit Setups Profiles Menu the erase confirmation window is displayed If confirmed as YES all patches and simulselects stored in the current setup will be erased These are the memory patches and simulselects seen with the Maestro lt Patch View gt or lt Simul View gt keys If lt Enter gt is pressed the default answer of NO is accepted and nothing is erased Confirm E E patch ss N Figure 13 Clear Patch Simulselects Erase Confirmation Window 7 4 COPY SETUP When Copy Setup is selected from the Edit Setups Profiles Menu a window is displayed The source setup is the one
41. to accept the edit changes Figure 25 shows the two windows The windows use the same navigation and editing keys that are used when editing entities Care should be taken to keep the width of the text for indicators exactly the same do not to exceed the width of the warning error banner 31 LBI 39056 HIGHLIGHTED STRING V3 00 2 ACTV 3 ii CALL CG EDIT WINDOW EMER Figure 25 Text String Edit Windows 10 VIEW AUX I O When View Aux I O is selected the Aux I O window shown in Figure 26 is displayed This window is for viewing only Editing of this data is done only at the CEC IMC Manager There are 30 auxiliary I O events to view The up down arrow page and home end keys can be used to view the other events lt Esc gt returns the user to the previous menu Table 14 describes each field NUM TYPE STATE BIT ACT DEACT MESSAGE H 0 Fl MOM 1 1 F2 2 EMERG 1 2 3 4 5 6 7 8 9 BACKUP SYSTEMS FAILURE e H e o H N INPUT 6 ACTIVE PPR a es w Figure 26 Aux I O Window 32 LBI 39056 TABLE 14 VIEW AUX I O FIELDS FIELD DESCRIPTION NUM The AUX I O event number 1 30 TYPE Type of event I Input O Output undefined STATE Active state that triggers input event or active output state H High L Low BIT Controlle
42. u Select other main editing functions or return to MS DOS 8 1 EDIT CONFIG DATABASE When Edit Config Database is selected the Configuration Data form shown in Figure 18 is displayed This figure shows default data The user can modify data by using the form navigation and text editing keys The numeric data fields have different field widths depending on the maximum value that may be entered The yes no fields in the right column can only contain yt or YN Table 11 describes the parameters on the Configuration Data form Parameters followed by an asterisk are not settable at the CEC IMC Manager these items can only be changed by the Editor Changes to parameters not marked with an asterisk will override values from the CEC IMC Manager and subsequent CEC IMC Manager configuration messages will override any Editor changes Default values are shown in square brackets 22 LBI 39056 Console Name MAESTRO Console ID 800 19 2K Baud Call Director ID Startup Setup Language CLB IRQ Speaker Config Tower PA Boards CTIS Hang Time System Msg Del AuxI O Msg del CONFIGURATION DATA O Alt Keyboard File Call Director I Call Alias Mod Prog Quick Save Mod Ignores DV Mode Default to DV Mode ZZZZZZK WNoOrRrNNA gt AIOF Figure 18 Configuration Data Form TABLE 11 EDIT CONFIGURATION DATABASE PARAMETERS PARAMETER DESCRIPTION AND VALID VALUES
43. vious text re appears upon the next key stroke any key The help text must be erased to continue 10 LBI 39056 5 MAIN MENU The Main Menu is the starting point from which all Editor operations begin This menu appears after the copyright screen and password window if enabled are displayed After an editing session has been completed the user will always return to the Main Menu before exiting to MS DOS The Main Menu is shown in Figure 4 EDITOR MAIN M t to DOS Esc Setups Profiles Configuration Language Files Aux I O nge Password ut Editor Table 3 briefly describes the actions that follow a menu selection and how the menu selection is used Most of the menu Figure 4 Editor Main Menu items have an entire section devoted to their use Hot key letters are shown in bold type TABLE 3 MAIN MENU SELECTIONS MENU ITEM ACTION USE Edit Entity Database Accesses the entity database edit screen Editing of entity database file ENTITY DAT This includes the entity name privilege and home site Section 6 Edit Setups Profiles Displays the Edit Setups Profiles Menu Editing of user profiles setup titles and page names Clearing startup modules patches and simulselects Section 7 Edit Configuration Displays the Edit Configuration Menu Editing console configuration including hardware parameters site names and screen col
Download Pdf Manuals
Related Search