Technical Data
Contents
1. Sequence table Con _ ab page left intentionally blank 18 JARAG 5 User Manual2. 2 DMX primary data 3 DMX primary data 4 Not connected 5 Not connected RS232 Function SubD 9 pin female Type Serial link to PC Pinout Not connected TX output RX input DTR input Ground Not connected Not connected Not connected Not connected OO JO O1 P ND JARAG 5 User Manual Con _ Indicators POWER Off No power or fuse blown Green Power on STATUS Off Normal operation Red Malfunction Maintenance required DMX Off No DMX signal Green DMX signal OK Green flashing Occasional DMX errors poor quality DMX signal orange Check the connections and signal integrity Red DMX connection fault or polarity inversion DMX signal not usable JARAG 5 User Manual 9 ab _ Setup menu The setup menu uses the following keys Navigation through the menu Setting a value ENTER Select sub menu Save the value EXIT Exit sub menu Cancel changes Next item Increase the value Previous item Reduce the value Holding down the or key increases the rate of change When a value is being changed all 4 decimal points are lit on the display By default the display is either blank or shows the DMX address of the lighting system To enter the setup menu press lt ENTER gt The display automatically returns to its
3. 6 channel mode the 25 lamp sequence is controlled by the built in sequencer controlled by DMX using 6 channels to control all 25 lamps The sequences are controlled by DMX selection of the sequence speed of sequencing overall brightness fade time between steps orientation and reflection of the patterns The sequencer can store 256 32 step sequences each step defining the state of all 25 lamps Any lighting pattern can be defined as well as transitions The first 128 sequences are defined internally and are the same for all JARAG 5s providing a firm basis for creating lighting effects with the same controls for any lighting system see description of sequences in the appendix All of the remaining 128 sequences can be defined by the user to meet his requirements Pre coding special sequences makes it possible to have optimal light sequences for each lighting system The sequences are programmed using special software supplied free of charge downloaded from www chromlech com that operates under PC Windows The sequences can be defined and then uploaded into the lighting systems A graphic interface allows for simulating the sequences that have been defined 25 DMX channel personality The 25 DMX channel personality is used to control the 25 lamp array directly each DMX channel corresponds to one lamp In this case the internal sequencer and the sequences it contains are not used 31 DMX channel personality The 31 DMX channel
4. OMIEL SIMULT le malt ils EE JARAG 5 User Manual Rev D JA121 JA221 FW V2 3 Chromlech 19 avenue Gabriel Faur 35235 THORIGNE FOUILLARD FRANCE Tel 33 0 2 23 20 77 67 Fax 33 0 2 23 20 75 71 E mail contact chromlech com Web www chromlech com ab Table of Contents TABS or Contents tears eae ge Ge nn ned ne 1 We TMG AAG EE 2 Lamp e E 2 Internal sequencer ee 2 6 DMX channel personality EE 3 25 DMX channel personality essentiel ege te datent 3 31 DMX channel personality E 3 JAIZ I dINEnsSIonsS M E a name 4 JA221 dimensions 4 2 NS AMOR EE 5 Direct E Le EE 5 Using the yoke MOuUntNg beer 5 Stacking amay EE 5 Ke e 6 4 GONr l eu WEE 7 CONNECTIONS RE 8 LAS Le ue EE EE 9 SSL menu ee 10 Setup menu structure ii iiiiiiiiieeeeeereeererrrereneeeeneeeeeeeeeeeneeene 10 EENHEETEN 12 6 channel personality sequences ccinesecincteesencscanssecterscecendedaenenssceteecntacssensaecsnassecneraedacte 12 25 channel personality matrix entente din nine ee 14 31 channel personality te E 14 0 PrograMMiNG ee Ee 15 Eer e EE 16 Ge Part lee E 16 SCQUGICES e EE 17 JARAG 5 User Manual 1 one _ 1 The JARAG 5 The JARAG 5 provides the same light output as a conventional lighting system but can be used to create a wide range of lighting effects The dimmers sequencer and control interfaces are built in so that the system can be installed simply and easily It only requires a ma
5. Rotation 0 12 None 0 13 2590 Vertical 0 26 37 Horizontal 0 38 50 Vertical horizontal 0 51 62 None 90 63 75 Vertical 90 76 87 Horizontal 90 88 100 Vertical horizontal 90 Channel 5 Sequence selection 0 Sequence 1 to 100 Sequence 16 Channel 6 Sequence bank selection 0 Bank 1 to 100 Bank 16 JARAG 5 User Manual one _ 13 Crone 25 channel personality matrix The intensity of each lamp is directly controlled by a DMX channel as for a conventional dimmer and the built in sequencer is disabled The following schematic shows the channel assignments for the lamps 0060006 Channel 1 to 25 Intensity 0 Off to 100 Full On 31 channel personality dual Each lamp is controlled simultaneously by the built in sequencer 6 channel mode and individually as an array 25 channel mode The lighting system calculates the intensity from the two modes using HTP Highest takes Precedence for each lamp individually Channel 1 to 6 Sequence control 6 channel mode Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Intensity Speed step Cross fade low voltage lamp effect Rotation reflection Sequence Sequence bank Channel 7 to 31 Matrix control 25 channel mode Channel 7 Lamp 1 Channel 31 Lamp 25 14 60000 06060606 00000 00000 JARAG 5 User Ma
6. dimmer Switch off unit before disconnecting mains The lighting system should be disconnected from the mains before any maintenance or relamping operation The rear panel must not be opened when the lighting system is powered up Refer servicing to qualified service personal only Before use check that the lighting system cable and plug are in good conditions and that the power supply used is correctly earthed The lighting system should not be exposed to rain or water Not for residential use The lighting system must always be secured with an appropriate safety cable Intense heat Lamps are hot Avoid contact by persons and materials WARNING Read users guide for safety instructions Min distance to flammable material 0 6 m Min distance to illuminated surface 1 60m Maximum ambient temperature ta 35 C Maximum exterior surface temperature 100 C CAUTION Risk of fire and electric shock Use PAR lamps 75W max with aluminium reflector only Replace fuse FU1 and FU2 only with fuse of same type and rating 230V lamps 6 3x32mm T 10A 250V or 115V lamps 6 3x32mm T 20A 250V NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed
7. 5 channels Value Dimm Dimmer channel intensity for the sequence Sped Speed channel speed or step selection for the sequence Fade Fade channel cross fade and LV halogen emulation Seq Sequence channel selects the sequence Banh Bank channel selects the sequence bank Disp Function Sets the default display mode Value On the display shows the DMS of the lighting system continuously Off the display shows the DMX address and goes off after about 1 minute Dfit Function Restores the default settings Value This sets the following values DMX address 1 personality 6 channels rotation 0 display On JARAG 5 User Manual 11 ab pe 5 DMX control Three different DMX personalities are available 6 channel personality sequences 6 channel personality is used to replay sequences programmed in the built in sequencer Channel 1 Intensity 0 Off to 100 Full On Flash Full On starting from the first step of the sequence Channel 2 Speed Step 0 Off 3 Fast to 50 Slow 50 Step 1 to 95 Step 32 100 Synchronise sequence to first step Flash Channel 3 Cross fade Low voltage lamp effect 0 Fast to Off 50 Slow 50 Slow to On 100 Fast 12 JARAG 5 User Manual Channel 4 reflection
8. and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 6 JARAG 5 User Manual one _ 4 Control panel The main operating parameters can be set using the built in control panel This panel has four keys and a display and is located on the back of the lighting system The settings are stored in non volatile memory STATUS C DMX POWER 6 e e e e EXIT ENTER 060040 RS232 Control panel rear JARAG 5 User Manual 7 ab _ Connectors DMX IN Function DMX 512 input Type XLR 5 pin male Pinout 1 Shield ground 2 DMX primary data 3 DMX primary data 4 Not connected 5 Not connected DMX OUT Function DMX 512 output Type XLR 5 pin female Pinout 1 Shield ground
9. default state if no selection is made for 1 minute Setup menu structure 12 or Add F Led Set DMX address PErS Set DMX mode rot Rotation TEST Lamp test opo diMM m DIMMER CtrL Manual control I SPEC LL SPEED So ft J Software version I FACE em FADE DISP m Set display mode I Seq SEQUENCE I Banh BANK DfLt Default settings 10 JARAG 5 User Manual ab Addr Function Sets DMX address Value The value is the first DMX channel for the lighting system Minimum 1 Maximum 512 nominal Maximum value for 6 channel personality 507 Maximum value for 25 channel personality 488 Maximum value for 31 channel personality 482 Pers Function Sets DMX personality Value 6 ch 6 DMX channels using internal sequences 25ch 25 DMX channels direct array addressing 31ch 31 DMX channels internal sequences array using HTP See chapter 5 for the assignment of the channels Rot Function Sets rotation of the lighting system Value UP no rotation UC 90 rotation dN 180 rotation gt A 270 rotation Test Function Lights all the lamps for testing Value Test selected all the lamps are lit at low power Ctrl Function Manual control of the lighting system using
10. ins supply and an external DMX controller Lamp array The JARAG 5 has a 25 lamp array The type of lamp used depends on the lighting system model The JA121 takes PAR20 lamps GU10 and the JA221 takes PAR30 lamps E26 The lamps are controlled individually by a built in 25 channel dimmer Internal sequencer The lighting system has an internal sequencer which makes it easier to control the lamp array The sequencer can store up to 256 sequences A sequence is a series of steps maximum 32 played in a loop and the brightness speed and effects can be adjusted in real time Each step defines the state of each of the 25 lamps The sequences are stored in 16 banks of 16 sequences The sequences for banks 1 to 8 are factory set and cannot be changed These sequences are common to all JARAG 5s and provide a firm basis for creating lighting effects with the same controls for any lighting system see description of sequences in the appendix The sequences for banks 9 to 16 can be defined by the user These sequences allow each lighting system to be set up to meet the user s requirements The sequences are programmed using special software supplied free of charge downloaded from www chromlech com that operates under PC Windows The sequences can be defined and then uploaded into the lighting systems A graphic interface allows for simulating the sequences that have been defined 2 JARAG 5 User Manual ab 6 DMX channel personality In
11. l 25 channel matrix channel 1 to 25 Intensity lamp 1 to 25 25 independent circuits DMX control 31 channel dual HTP Highest Takes Precedence prioritisation of 6 channel sequence and 25 channel array modes channel 1 to 6 Sequence control channel 7 to 31 Array control Kit of 25 PAR20 25 lamps for JA121 Kit of 25 PAR30 10 lamps for JA221 Yoke mounting for JA121 and JA221 Transport flight case for 2 x JA121 Transport flight case for 2 x JA221 Sequence programming software Manual control Manual digital control on rear panel with four keys and display Settings DMX address DMX personality lamp test rotation of the lighting system activating a sequence resetting to factory settings PC control RS232 C The lighting system can be controlled by a PC to upload and save sequences as well as setting up the lighting system Control program Can be downloaded from www chromlech com Requires a PC Win2K XP with RS232 C port for connection to the JARAGs Can be used to create prepare and simulate patterns and sequences without being connected to the lighting system Can be used to upload sequences to and save sequences from the lighting system as well as testing and setting up the lighting system using a built in control console Jarag 5 for aluminium reflector PAR20 GU10 lamps Jarag 5 for aluminium reflector PAR30 E26 lamps JARAG 5 User Manual JARAG 5 User Manual
12. nual 6 Programming The sequences are programmed using the Jarag Control Center This program can be downloaded from www chromlech com Further information can be found in the program documentation JARAG 5 User Manual one _ 15 Cronkch rem 7 Specifications Power supply Mains supply 230V 50Hz 8 2A 1875 W 115V 60Hz 16 4A 1875 W Built in dimmers Lamps 25x 115 or 230V 75W lamps JA121 Hi Spot ES63 25 2800K 2500h GU10 aluminium reflector JA221 Hi Spot ES95 10 2900K 3000h E26 aluminium reflector Chassis Matte black epoxy finish JA121 HxWxD 58 x 58 x 24 cm JA221 HxWxD 58 x 58 x 27 cm Weight without lamps 9 4 kg Attachment Yoke mounting or M10 holes on chassis Stacking JARAG systems can be stacked while maintaining a constant spacing between the lamps Connectors Mains cable Neutrik PowerCon DMX in XLR5 DMX out XLR5 RS232 C SubD9 8 Part numbers JA121 JA221 JA102 JA202 JA123 JA124 JA224 JA105 16 Sequencer Built in sequencer with up to 256 32 step sequences controlled by DMX 128 sequences 8 banks of 16 are factory defined the remaining 128 can be user programmed DMX control 6 channel sequence channel 1 Intensity channel 2 Speed channel 3 Effects channel 4 Rotation H V reflection channel 5 Sequence channel 6 Sequence bank variable cross fade low voltage lamp emulation DMX contro
13. personality makes it possible to use the 6 channel sequencer mode at the same time as the 25 channel matrix mode The lighting system uses a Highest Takes Precedence HTP priority system for each lamp This allows a matrix controller to be used for example for overall animation of a JARAG light wall while still being able to use the internal sequences that can be superimposed as required JARAG 5 User Manual 3 a JA121 dimensions 576mm JA121 front view JA221 dimensions 63 mm diam 576mm JA221 front view 200 mm 200 mm JA121 side view 200 mm 200 mm JA221 side view JARAG 5 User Manual ab 2 Installation The JARAG 5 can be installed in any orientation Direct fastening There are 24 M10 holes on the edges of the JARAG 5 chassis 12 at the front and 12 at the back so that the lighting system can be suspended using hooks slings or shackles Using the yoke mounting The yoke mounting is attached to 4 holes on the side of the JARAG 5 to adjust the inclination and orientation of the lighting system easily Stacking arrays The JARAG 5 lighting systems can be stacked to form larger arrays using M10 bolts in the side holes JARAG 5 User Manual 5 one _ 3 Precautions in use The JARAG 5 lighting system has its own power control unit and is designed to be connected directly to the mains It must not be powered through a
Download Pdf Manuals
Related Search