NDS3208 8 in 1 MPEG-2 Encoder User`s Manual
Contents
1. so users can just check the physical address under this interface and the modification must be done in the network updating tools 4 1 4 MAC Address 201012345679 NOTE The MAC address is unique and cannot be modified When the MAC address is ffffffffffff users must modify the address through special software otherwise the IP output data will be filter out when the IP stream passes through the router a mu DE OINC y All the specifications are subject to change without any further notice All rights reserved ZFAdd No 10 amp No 12 Wuxing Fourth Road Wuhou District Chengdu 610045 Sichuan PR China Awww dsdvb com English TWTel 86 028 85558928 Fax 86 028 85585255 t amp Email sunyu dsdvb com 15 29 al 3 2 5 Save Configuration Users can save the modification by pressing the enter key and it will display the following interface when user press the enter key 5 1 Save Configuration 5 2 Restore configure 5 3 Factory Set 3 2 6 Version Users can check the device software version and hardware version and the LCD will display the following interface when users press the ENTER key in 1 Encoder SW X XXF 3 2 Language User can select the needed language under this submenu Language 1 English 2 F X a mum DE OI y All the specifications are subject to change without any further notice All rights reserved ZFAdd No 10 amp No 12 Wuxing Fourth Road Wuhou District Chengdu 610045 Sichuan2. 11 29 DEGING NDS3208 8 in 1 MPEG 2 Encoder User s Manual gt 3 Encoder Param 4 Output IP 3 2 1 1 Encoder Enable This is for user to choose to output the program or not Encoder Enable ON OFF 3 2 1 2 Video Param User can adjust the relevant parameters of input video in submenus of Brightness Contrast Saturation and Hue The adjustable range is 0 255 while the adjustable range of Hue is 127 127 The figure outside the parentheses is decimal while the inside is hexadecimal NOTE Below explanations are applied in this entire manual 1 To press ENTER to start editing 2 To move the underline through LEFT RIGHT keys 3 To modify the value of underlined character through UP DOWN keys 2 1 Brightness 0 255 128 2 2 Contrast 0 255 128 2 3 Saturation O 255 128 2 3 Hue 127 127 000 3 2 1 3 Encoder Param User can modify the video audio encoding bit rate and program information under this menu a mu DE OINC y All the specifications are subject to change without any further notice All rights reserved ZFAdd No 10 amp No 12 Wuxing Fourth Road Wuhou District Chengdu 610045 Sichuan PR China Awww dsdvb com English Tel 86 028 85558928 Fax 86 028 85585255 t amp Email sunyu dsdvb com 12 29 DEING NDS3208 8 in 1 MPEG 2 Encoder User s Manual 3 1 Video Bitrate 1000 19500Kbps 4 500Kbps 3 2 Audio Bitrate 64 320Kbps optional gt 64Kbps 3 3 Pro info 3 2 1 4
3. Layer2 e Supports MPEG 2 encoding format e Supports CBR e Supports IP output MPTS or 8 SPTS output over UDP RTP RTSP e Support PCR accurate adjusting e Support PID re mapping and passthrough e Support PSI SI editing e Supports PAL and NTSC SD video formats e Real time effective encoding output bit rate monitoring e Supports web NMS operation e Keyboard and LCD operation 1 3 Principle Chart s ma DE OINC 7 All the specifications are subject to change without any further notice All rights reserved Add No 10 amp No 12 Wuxing Fourth Road Wuhou District Chengdu 610045 Sichuan PR China Awww dsdvb com English WTel 86 028 85558928 Fax 86 028 85585255 Email sunyu dsdvb com 1 29 DEGING NDS3208 8 in 1 MPEG 2 Encoder Users Manual o O AV 2 rH Ci E S AV 6 z a CE ee AV 7 CRI AV 8 aeei CRED ASI a ASI Output IP Output 1xMPTS amp 8xSPTS 1 4 Specifications 8xCVBS inputs BNC interface Input 8 pairs of unbalanced audio inputs BNC interface 1xASI input BNC interface Resolution PAL 720x576_50i1 NTSC 720x480_60i Encoding MPEG 2 Video Bit rate 1Mbps 19 5Mbps Rate Control CBR Chroma 4 2 0 Aspect Ratio 4 3 Encoding MPEG 1 Layer2 Audio Sampling rate 48KH Resolution 24 bit Bit rate 64Kbps 384Kbps each channel 1 ASI input multiplexed with local 8 channel SPTS Multiplexing PID re mapping or passthrough PCR accurate adjusting PSI SI editing 2 x ASI outpu
4. or customize the input and output parameters setting The detail operations go as follows Keyboard Function Description ENTER Activating the parameters which need modifications or confirming the change after modification MENU To cancel presently entered value resume previous setting and return to previous menu LEFT RIGHT To move the gt to choose or set the parameters UP DOWN To modify activated parameter or page up down when parameter is inactivated LOCK To Lock the screen cancel the lock state After pressing lock key the system will question the users to save present setting or not If not the LCD will display the current configuration state At the Factory Configuration page user can press ENTER key to restore the factory default configuration 3 1 Initializing After powering on the device it will take a few seconds to initialize the system and then the LCD will show the device name and output real time bit rate in the first row while the 8 channels respective serial number and input real time encoding bit rate in the second row in turn It shows as below in 1 Encoder 1P 02 94M 2P 02 73M 3P 02 92M 4P 02 90M 3 2 General Setting By pressing LOCK key users can enter in the main menu and set the input and output a mu DE OINC y All the specifications are subject to change without any further notice All rights reserved ZFAdd No 10 amp No 12 Wuxing Fourth Road Wuhou Dis
5. range and the connection 1s correct before switching on device Checking the RF output level varies within tolerant range if it is necessary Checking all signal cables have been properly connected Frequently switching on off device is prohibited the interval between every switching on off must greater than 10 seconds Conditions need to unplug power cord Power cord or socket damaged Any liquid flowed into device Any stuff causes circuit short Device in damp environment Device was suffered from physical damage Longtime idle After switching on and restoring to factory setting device still cannot work properly Maintenance needed a mu DE OINC y All the specifications are subject to change without any further notice All rights reserved ZFAdd No 10 amp No 12 Wuxing Fourth Road Wuhou District Chengdu 610045 Sichuan PR China Awww dsdvb com English TTel 86 028 85558928 Fax 86 028 85585255 t amp Email sunyu dsdvb com 26 29 DEGING NDS3208 8 in 1 MPEG 2 Encoder Users Manual Chapter 6 Packing list NDS3208 8 in 1 MPEG 2 Encoder Ipcs User s manual I pcs Analog Audio Video Composite Input Cable 8 pcs ASI cable Ipcs Power cord Ipcs s mu DE OINC y All the specifications are subject to change without any further notice All rights reserved ZFAdd No 10 amp No 12 Wuxing Fourth Road Wuhou District Chengdu 610045 Sichuan PR China Awww dsdvb com English WTel 86 028 85558928 Fax 86 028 85585
6. 10045 Sichuan PR China Awww dsdvb com English WTel 86 028 85558928 Fax 86 028 85585255 t Email sunyu dsdvb com 3 29 DEGING NDS3208 8 in 1 MPEG 2 Encoder Users Manual 6 25AStoupapons 5 NMS ONerwork management pom O 9 PowerSwim s mm DE OINC F All the specifications are subject to change without any further notice All rights reserved lt Add No 10 amp No 12 Wuxing Fourth Road Wuhou District Chengdu 610045 Sichuan PR China Awww dsdvb com English WTel 86 028 85558928 Fax 86 028 85585255 t Email sunyu dsdvb com 4 29 DEGING NDS3208 8 in 1 MPEG 2 Encoder User s Manual Chapter 2 Installation Guide 2 1 Acquisition Check When users open the package of the device it is necessary to check items according to packing list Normally it should include the following items NDS3208 8 in 1 MPEG 2 Encoder User s Manual Analog Audio Video Composite Input Cable ASI Cable Power Cord If any item is missing or mismatching with the list above please contact local dealer 2 2 Installation Preparation When users install device please follow the below steps The details of installation will be described at the rest part of this chapter Users can also refer rear panel chart during the installation The main content of this chapter including Checking the possible device missing or damage during the transportation Preparing relevant environment for installation Installing Encoder Connecting signal c
7. 255 t Email sunyu dsdvb com 21 29
8. 818 3 Audio Ox3a Apply Close Figure 4 Input new data and click Apply button at last to confirm the modification PID Pass Clicking Mi it displays the interface where to add the PIDs which need pass through Figure 5 In some occasions there are some PIDs which won t belong to any program such as EPG NIT tables and so on which user just wants to pass them through the multiplexing module without changing anything This is the main purpose of this function PID Pass Index Channel Input PID Output PID NEXT 9 0x1 0x1 Add Apply Close Figure 5 Click Add to add more boxes for filling the Input amp Output PIDs then click Apply to confirm System Output Click Output it displays the interface where users can configure the IP output it include SPTS MPTS and ASI output s mu DE OINC y All the specifications are subject to change without any further notice All rights reserved ZFAdd No 10 amp No 12 Wuxing Fourth Road Wuhou District Chengdu 610045 Sichuan PR China Awww dsdvb com English WTel 86 028 85558928 Fax 86 028 85585255 Email sunyu dsdvb com 20 29 DEING SPTS Settings NDS3208 8 in 1 MPEG 2 Encoder Users Manual Under this menu user can configure the 8 output SPTS parameters separately Figure 6 Output Parameters Here you can configure the ip output it includes spts and mpts but output bit rate should not over 100Mbps sPTS Settings MPTS Settings DATA I
9. DEGING NDS3208 8 in 1 MPEG 2 Encoder User s Manual NDS3208 8 in 1 MPEG 2 Encoder NMS Version 1 12 5 SW 2 07 HW 1 3 a mm DE QIN j All the specifications are subject to change without any further noftice All rights reserved Add No 10 amp No 12 Wuxing Fourth Road Wuhou District Chengdu 610045 Sichuan PR China ANwww dsdvb com English WTel 86 028 85558928 amp Fax 86 028 85585255 t amp Email sunyu dsdvb com DIRECTORY Chapter 1 Product Introduction 000 0 eee ccccccccessccessseceeseceesseccesseecesssecessseceesseccesseecesseecesseecessecesaeeess 1 Ded OUNO eiae e E E E E E EENE AEE EALE AE EEN E TEE E EEE 1 te MAET o UO aE EE E E E E E A AEE EE AE E E EEE 1 To PUNCO CRI en a n E rey 1 TAPEEC ANO ee eh ee E N 2 1 5 Appearance and INIUStration oo ccccssccccssseecesesseeecessseeeessseecessseeecseseesesesseeeeeesseeceeeseesesesaeees 3 Chapt r 2 Installation GUIGG oocesecssccescnnnnnesnnnaninaninia aaa 5 ZACION ORO C1 eenen EEEE EE EA AEE E E EAEE AE E EE 5 2 2 MSTANATIO NMP FE DAN ATION sssini aaa aaa Naa 5 29 VINES S COMME CMON sr E E E AA 7 2 4 Signal Cable Connection ccc cccccccsccessccessecessecesseccessecesecesecessecesseeceseeceseecessecesseceeseeeeseeeeeees l onapter s SAO araea E EAE AEE de OE A EAE Ai 10 SA e a aE E E EE A E EE E OEE E EAE 10 ZG SA LUNG a N S O ENN 10 Chapter 4 NMS 9 2116 9 eee eee ET E A R 17 4 1 Login Interface 00 cc ccc cccccsssceesssecessseeessseecessseceessec
10. Fourth Road Wuhou District Chengdu 610045 Sichuan PR China Awww dsdvb com English WTel 86 028 85558928 Fax 86 028 85585255 t Email sunyu dsdvb com 7 29 DEING NDS3208 8 in 1 MPEG 2 Encoder Users Manual 2 4 2 ASI output cable illustration 2 4 3 Network Cable illustration CAT5 2 4 4 Unbalanced audio and CVBS video input connection User can firstly find the CVBS input connector on the device according to the connector mark described on the rear panel illustration and then connect the analog CVBS video and unbalanced audio cables in the accessories One end is connected to the signal source equipment while the other end to the encoder s CVBS input port The encoder s Analog Composite Video input port and its connection are illustrated as follows 2 4 5 ASI output interface connection s mmm DE Onn 7 All the specifications are subject to change without any further notice All rights reserved Add No 10 amp No 12 Wuxing Fourth Road Wuhou District Chengdu 610045 Sichuan PR China Awww dsdvb com English WTel 86 028 85558928 Fax 86 028 85585255 t Email sunyu dsdvb com 8 29 a User can firstly find the ASI output interface on the device according to the connector mark described on the rear panel illustration and then connect the ASI cable in the accessories One end is connected to the encoder s ASI out connector ASI1 ASI2 while the other end to the TS stream multiplexer or modulator s A
11. Output IP User can set the SPTS output IP parameters under this menu The device will display the following page after users pressing the enter key Users can decide to 4 1 Output Enable 1 OFF output the SPTS or not and choose output 4 2 Filter Null PKT IP protocol 4 3 Dest IP Address Users can set 4 4 Destination Port Destination IP Address d Port h and Port here 4 5 Out Bitrate Kbps 3 2 2 MPTS Output Setting User can set the MPTS output IP parameters under this menu The device will display the following page after users pressing the enter key Users can decide to 2 1 Output Enable 1 OFF tout th MPTS oe ae a 2 2 Filter Null PKT not and choose output IP t l dia 2 3 NIT Insert 2 4 Dest IP Address 2 5 Destination Port 2 6 Out Bitrate Kbps a mu DE ONC y All the specifications are subject to change without any further notice All rights reserved ZFAdd No 10 amp No 12 Wuxing Fourth Road Wuhou District Chengdu 610045 Sichuan PR China Awww dsdvb com English WTel 86 028 85558928 Fax 86 028 85585255 t amp Email sunyu dsdvb com 13 29 al Users can copy a 1 MPTS 2 7 ASI output stream from the IP out streams 1 MPTS amp 8 SPTS to output through ASI 2 8 TSID and ONID 3 2 3 MUX Setting Under this menu user can choose programs to mux out 3 1 Channel 1 3 2 Channel 2 3 7 Channel 7 3 8 Channel 8 3 9 ASI Ch
12. P Settings E hn a n n e Ove myi e Interface CHANT UDP CHAN gt RTPIRTSP Status MAC Addr 01 00 5E 02 02 02 Output IP 224 2 2 2 Output Port 1002 Output Bitrate 4 801 Mbps MAC Addr 01 00 5E 02 02 02 Output IP 224 2 2 2 Output Port 1003 Output Bitrate 4 795 Mbps MAC Addr 00 00 00 00 00 00 Output IP 224 2 2 2 Output Port 1004 Output Bitrate 4 797 Mbps MAC Addr 00 00 00 00 00 00 Output IP 224 2 2 2 Output Port 1005 Output Bitrate 4 818 Mbps MAC Addr 00 00 00 00 00 00 Output IP 224 2 2 2 Output Port 1006 Output Bitrate 4 786 Mbps MAC Addr 00 00 00 00 00 00 Output IP 224 2 2 2 Output Port 1007 Output Bitrate 4 81 Mbps MAC Addr 00 00 00 00 00 00 Output IP 224 2 2 2 Output Port 1008 Output Bitrate 4 8 Mbps MAC Addr 00 00 00 00 00 00 Output IP 224 2 2 2 Output Port 1009 Output Bitrate 4 786 Mbps Actions To modify the output SPTS parameters as needed By clicking this button to pop up a dialog box as below a mu DE OINC y All the specifications are subject to change without any further notice All rights reserved ZFAdd No 10 amp No 12 Wuxing Fourth Road Wuhou District Chengdu 610045 Sichuan PR China Awww dsdvb com English TWTel 86 028 85558928 Fax 86 028 85585255 Email sunyu dsdvb com 21 29 al Channel 1 s IF Output OFF t OFF To not output Filter Null Fkt NO UDP the corresponding Dest IP Addr 224 2 2 2 RTRIRTSP SPT
13. PR China Awww dsdvb com English TWTel 86 028 85558928 Fax 86 028 85585255 Email sunyu dsdvb com 16 29 DEGING NDS3208 8 in 1 MPEG 2 Encoder Users Manual Chapter 4 NMS Operation Network Management System Profile Network management system is applied to digital TV equipment operation control and management and parameters setting etc It centralizes digital TV equipment through network 4 1 Login Interface The factory default IP address is 192 168 2 136 and users can connect the device and web NMS through this IP address Connect the PC Personal Computer and the device with a net cable and use ping command to confirm they are on the same network segment For instance the PC IP address is 192 168 99 252 we then change the device IP to 192 168 99 xxx xxx can be 0 to 255 except 252 to avoid IP conflict Launch the web browser an input the device IP address in the browser s address bar and press Enter It will display the Login interface as Figure 1 Input the Username and Password Both the default Username and Password are admin And then click Sign In to start the device setting Welcome Username Password Defaut User admin Defaut Password admin Figure 1 User can login the NMS by pressing OK key after inputting user name Upon the inputs the software will verify them with database record automatically and the main interface will a mu DE OINC y All the specifications are subject to chang
14. S Pi Dest Port 1002 Output Bitrate 10000 kbps Trans Stream ID 1 Original Network IO 1 Close Apply Input new data and click Apply button at last to confirm the modification MPTS Settings Under this menu user can configure the output MPTS Parameters Figure 6 Output Parameters Here you can configure the ip output itincludes spts and mpts but output bit rate should not over 100Mbps SPTS Settings MPTS Settings DATA IP Settings ASI Output Output IP OFF vo 224 2 2 2 Output 1001 Destination Mac Addr Output Bitrate 60000 Kbps Trans Stream ID 0 Original Network ID 0 Filter Null Pkt NO v NIT Instertion NO v Figure 6 DATA IP Settings Data IP Setting is for setting the Data parameters for the device Figure 6 s mu DE OINC y All the specifications are subject to change without any further notice All rights reserved ZFAdd No 10 amp No 12 Wuxing Fourth Road Wuhou District Chengdu 610045 Sichuan PR China Awww dsdvb com English WTel 86 028 85558928 Fax 86 028 85585255 Email sunyu dsdvb com 22 29 DEING NDS3208 8 in 1 MPEG 2 Encoder User s Manual Output Parameters Here you can configure the ip output itincludes spts and mpts but output bit rate should not over 100Mbps SPTS Settings MPTS Settings DATA IP Settings ASI Output IP Addr 192 168 4 137 Submask 255 255 255 0 Gateway 192 168 4 1 Mac Addr 40 70 74 76 78 FA Figure 7 ASI Output Clicking ASI Output f
15. SI input port The encoder s ASI output interface and its connection are illustrated as follow 2 4 6 IP Output Interface connection Users can firstly find the DATA interface on the device according to the connector mark described on the rear panel illustration and then connect the network CATS One end of the network cable is connected to the encoder s DATA output connector while the other end to the TS stream multiplexer IP input port or other device which can input IP signal The encoder s DATA connection 1s illustrated as follows 2 4 7 NMS Connection Users can firstly find the NMS interface on the device according to the connector mark described on the rear panel illustration and then connect the network CATS One end of the network cable is connected to the encoder s NMS connecter while the other end to the computer or the PC The encoder s NMS connection is illustrated as follows mm DE Onn r All the specifications are subject to change without any further notice All rights reserved Add No 10 amp No 12 Wuxing Fourth Road Wuhou District Chengdu 610045 Sichuan PR China Awww dsdvb com English WTel 86 028 85558928 Fax 86 028 85585255 t Email sunyu dsdvb com 9 29 DEGING NDS3208 8 in 1 MPEG 2 Encoder User s Manual Chapter 3 Operation NDS3208 8 in 1 MPEG 2 Encoder s front panel is user operating interface Before operating user can decide whether directly use the default setting
16. Set Local Save save this config file to local Download Local Load upload local file to device paz Upload Figure 9 System Network When user clicks Network it will display the screen as Figure 10 It displays the network information of the device Here user can change the device network configuration as needed Network IP Adar The manege address use this address to visit the manege web The format is wxx woooxilike as 192 168 0 1 After set the IP addrress you must use the new address to visit the manege web Submask General is 255 255 2550 itis mustthe same in a local area network Gateway Ifthe device is in different net segment you must set the gateway IP Addr 192 168 2 136 Submask 255 255 255 0 Default Gateway 192 168 2 1 Web Listen Port 80 O 65535 After saving restart valid Figure 10 a mu DE OINC y All the specifications are subject to change without any further notice All rights reserved ZFAdd No 10 amp No 12 Wuxing Fourth Road Wuhou District Chengdu 610045 Sichuan PR China Awww dsdvb com English WTel 86 028 85558928 Fax 86 028 85585255 Email sunyu dsdvb com 24 29 a System Password When user clicks Password it will display the password screen as Figure 11 Here user can change the Username and Password for login to the device After putting the current and new Username and Password click Apply to save the configuration Password Mod
17. ables Connecting communication port 1f it is necessary 2 2 1 Device s Installation Flow Chart is Illustrated as following Acquisition Fixing Connecting Grouding Wie erate Connecting Setting Running Check Device Signal Wire Parameter Device Power Cord 2 2 2 Environment Requirement a mu DE Onn F All the specifications are subject to change without any further notice All rights reserved lt Add No 10 amp No 12 Wuxing Fourth Road Wuhou District Chengdu 610045 Sichuan PR China Awww dsdvb com English WTel 86 028 85558928 Fax 86 028 85585255 t Email sunyu dsdvb com 5 29 G DEYING NDS3208 8 in 1 MPEG 2 Encoder User s Manual When user installs machine frame array in one machine hall the Machine Hall Space distance between 2 rows of machine frames should be 1 2 1 5m and the distance against wall should be no less than 0 8m Electric Isolation Dust Free Machine Hall Floor Meee aly oi ground E material 1X10 1X10 Grounding current limiting resistance 1M Floor bearing should be greater than 450Kg m Environment 5 40 C sustainable O 45 C short time Temperature installing air conditioning is recommended Relative Temperature 20 80 sustainable 10 90 short time Moore Window Installing moba strip for sealing door gaps and dual level glasses for window It can be covered with wallpaper or brightness less paint Fire Protection Fire alarm system and extinguisher Requiring devi
18. annel Users can choose to 3 10 PID remap remap PID or not Channel 1 8 represent the CVBS input ASI Channel represents the ASI input User could parse and select program s to mux out The setting principle is the same for channel 1 8 and ASI Channel Here take Channel as example 3 1 Channel 1 Press Enter key to get the program list tec e eee Seer eee e Sees eee OLJCCTYV 1 Press Enter key to choose to output the program or not Choose Vv to output the corresponding WV program Choose xX to not output mu DE OINC y All the specifications are subject to change without any further notice All rights reserved ZFAdd No 10 amp No 12 Wuxing Fourth Road Wuhou District Chengdu 610045 Sichuan PR China Awww dsdvb com English TWTel 86 028 85558928 Fax 86 028 85585255 Email sunyu dsdvb com 14 29 DEING NDS3208 8 in 1 MPEG 2 Encoder User s Manual 3 2 4 Network Setting Users can set the network parameters by pressing the enter key and the LCD will display the following interfaces 4 1 NMS Interface Set the Data interface 4 2 Data Interface parameters here 4 3Web Listen Port 4 1 NMS Interface user can set the parameter of NMS to connect with PC 4 1 1 IP Address 192 168 002 136 4 1 2 Subnet Mask 255 255 255 000 4 1 3 Default Gateway 192 168 002 001 The MAC address is read only in the keyboard operation interface
19. ce power air conditioning power and lighting Power power are independent to each other Device power requires AC power 220V 50Hz Please carefully check before running 2 2 3 Grounding Requirement All function modules good grounding designs are the basis of reliability and stability of devices Also they are the most important guarantee of lightning arresting and interference rejection Therefore the system must follow this rule Coaxial cable s outer conductor and isolation layer should keep proper electric conducting with the metal housing of device Grounding conductor must adopt copper conductor in order to reduce high frequency impedance and the grounding wire must be as thick and short as possible Users should make sure the 2 ends of grounding wire well electric conducted and be antirust Itis prohibited to use any other device as part of grounding electric circuit The area of the conduction between grounding wire and device s frame should be no less than 25mm a mum DE Onc F All the specifications are subject to change without any further notice All rights reserved lt Add No 10 amp No 12 Wuxing Fourth Road Wuhou District Chengdu 610045 Sichuan PR China Awww dsdvb com English WTel 86 028 85558928 Fax 86 028 85585255 t Email sunyu dsdvb com 6 29 DEGING NDS3208 8 in 1 MPEG 2 Encoder User s Manual 2 2 4 Frame Grounding All the machine frames should be connected with protective co
20. e without any further notice All rights reserved ZFAdd No 10 amp No 12 Wuxing Fourth Road Wuhou District Chengdu 610045 Sichuan PR China Awww dsdvb com English Tel 86 028 85558928 Fax 86 028 85585255 Email sunyu dsdvb com 17 29 a appear 4 2 Operation System Encoder From the menu on top side of the webpage clicking Encoder it displays the information of the programs from the X encoding board as Figure 2 User can click any item here to enter the Encoder Save Load 5 corresponding interface Input channel selection area The MUN Network h k f e l E to check information or interface and setting principle of asswor Output T the parameters each channel are the same J Here you can configure the encoder parameters Click button Init can reset theerCoder chip and re encoder 7 Video I Brightness 128 0 255 Norm PAL_BDGHIN Contrast 128 0 255 l l Encoding Saturation 128 0 255 Bitrate 0 Mbps l I Hue 0 127 127 E _ h _ i Cid Video Bitrate 4500 Kbps 1000 19500 Kbps lI User can set the parameters udio Bitrate 256 Kbps v S of the video Driehtness Seba a Seea contrast saturation Hue and Video Audio Bitrate by ee respective slider Hardware 1 3 Software 2 07 Figure 2 cs Click this button to reset the encoder chip and re encoder Click this button to apply the de
21. essseceesseecesseceesseeesseecessaesceaeeceesseceseeeenas 17 i O ozo AE ceded AE AE E TAE E EA AE O AE E E E A TAE 18 Chapter 5 Troubleshooting oneeseeeseeseeesssesseesseesseesseessessoessessoesseesssesssesseesseesnessnrssoessoesseesseessressees 26 cD rO FACKING I Tre EEE 27 a ma DE QIN 7 All the specifications are subject to change without any further notice All rights reserved Add No 10 amp No 12 Wuxing Fourth Road Wuhou District Chengdu 610045 Sichuan PR China Awww dsdvb com English WTel 86 028 85558928 amp Fax 86 028 85585255 E Email sunyu dsdvb com DEGING NDS3208 8 in 1 MPEG 2 Encoder User s Manual Chapter 1 Product Introduction 1 1 Outline The NDS3208 8 in 1 MPEG 2 Encoder is a professional SD audio amp video encoding and multiplexing device It has 8 channel CVBS video input interfaces 8 pairs of unbalanced audio input interfaces supporting MPEG 2 video encoding and MPEG 1 Layer 2 audio encoding This device can simultaneously encode 8 channel SD audio amp video moreover it has an ASI input and can multiplex the input TS with the 8 encoded SPTS to generate a MPTS output In conclusion its high integrated and cost effective design makes the device widely used in varieties of digital distribution systems such as cable TV digital head end satellite digital TV broadcasting etc 1 2 Main Features e 8xCVBS video inputs 8 pairs of unbalanced audio inputs e 1x ASI input interface e Audio MPEG 1
22. fault setting of Input X Aon Click this button to apply the modified parameters a Click this button to choose color schemes and patterns System gt MUX s mm DE OINC y All the specifications are subject to change without any further notice All rights reserved ZFAdd No 10 amp No 12 Wuxing Fourth Road Wuhou District Chengdu 610045 Sichuan PR China Awww dsdvb com English WTel 86 028 85558928 Fax 86 028 85585255 B Email sunyu dsdvb com 18 29 DEGING NDS3208 8 in 1 MPEG 2 Encoder Users Manual Click MUX it displays the interface where nsers can confionre the Mux out MPTS Figure 3 Select the needed language English and P X Chinese optional MUX Here you can configure the mux out mpts s N Click this button Lose Locked L ose Locked to restart the Input Program Channel Output Program Channel f rE ogram Vhanne e ae d CH 1 ENCODER 1 CH 1 ENCODER 0 C evice P 257 Encoder 1 CH 2 ENCODER 0 l Program Number 257 i r CH 3 ENCODER 0 i Program ease 1 i MPD Remap i gt CH 4 ENCODER 0 0x CH 5 ENCODER 0 I 8 CVBS l PCR PID 0x111 l j Refresh Input I gt CH 6 ENCODER 0 Paani lt H Element PIDs l gt CH 7 ENCODER 0 8 l amp CH 2 ENCODER 1 i Refresh Output CH 8 ENCODER 0 Channels CH3 ENCODER 0 i CH9ASIO W CH4 ENCODER 0 l i l j CH 5 ENCODER 0 l i i CH 6 ENCODER 0 l l iii U
23. g CH7 ENCODER 0 i I CH 8 ENCODER 0 I EditPra 1 ASI Input iy Sa Yale en ee Output area Channel Input area Operation area PID Pass Hardware 1 3 Software 2 07 Figure 3 Configure Input Area and Output Area with buttons in Operation Area Instructions are as below PID Remar To enable disable the PID remapping Refresh Input F F reres mou fr refresh the input program information Refresh Output Fetes ouou r refresh the output program information gt Select one input program first and click this button to transfer the selected program to the right box to output Similarly user can cancel the multiplexed programs from the right box Program Modification The multiplexed program information can be modified by clicking the program in the output area For example first select the target a program in the output area then clicking e it triggers a dialog box Figure 4 where users can input new information a mu DE OINC y All the specifications are subject to change without any further notice All rights reserved ZFAdd No 10 amp No 12 Wuxing Fourth Road Wuhou District Chengdu 610045 Sichuan PR China Awww dsdvb com English TWTel 86 028 85558928 Fax 86 028 85585255 Email sunyu dsdvb com 19 29 al General Program Number 16 Program Name Encoder 1 PMT PID 0x38 PCR PID 0x39 Program Info 13818 2 Video 0x39 13
24. ify the login name and password to make the device safely lf forget the name or password you can reset it by keyboard in menu 4 2 The default login name and password is admin Also please note the capital character and lowercase character Current UserName admin Current Password New UserName New Password Confirm New Password Figure 11 a mu DE OINC y All the specifications are subject to change without any further notice All rights reserved ZFAdd No 10 amp No 12 Wuxing Fourth Road Wuhou District Chengdu 610045 Sichuan PR China Awww dsdvb com English WTel 86 028 85558928 Fax 86 028 85585255 Email sunyu dsdvb com 25 29 DEGING NDS3208 8 in 1 MPEG 2 Encoder User s Manual Chapter 5 Troubleshooting DEXIN s ISO9001 quality assurance system has been approved by CQC organization For guarantee the products quality reliability and stability All DEXIN products have been passed the testing and inspection before ship out factory The testing and inspection scheme already covers all the Optical Electronic and Mechanical criteria which have been published by DEXIN To prevent potential hazard please strictly follow the operation conditions Prevention Measure Installing the device at the place in which environment temperature between 0 to 45 C Making sure good ventilation for the heat sink on the rear panel and other heat sink bores if necessary Checking the input AC within the power supply working
25. pper strip The grounding wire should be as short as possible and avoid circling The area of the conduction between grounding wire and grounding strip should be no less than 25mm 2 2 5 Device Grounding Connecting the device s grounding rod to frame s grounding pole with copper wire 2 3 Wire s Connection The grounding wire conductive screw is located at the right end of rear panel and the power switch fuse power supply socket is just beside whose order goes like this power switch is on the left power supply socket is on the right and the fuse is just between them Connecting Power Cord User can insert one end into power supply socket while insert the other end to AC power Connecting Grounding Wire When the device solely connects to protective ground it should adopt independent way say share the same ground with other devices When the device adopts united way the grounding resistance should be smaller than 1Q Caution Before connecting power cord to NDS3208 8 in 1 MPEG 2 Encoder user should set the power switch to OFF 2 4 Signal Cable Connection The signal connections include the connection of input signal cable and the connection of output signal cable The details are as follows 2 4 1 Unbalanced audio and CVBS video input cable illustration s mu DE 0N F All the specifications are subject to change without any further notice All rights reserved lt Add No 10 amp No 12 Wuxing
26. rom the menu it will display the interface as Figure 6 where to choose TS to output from ASI Output Parameters Here you can configure the ip output itincludes spts and mpts but output bit rate should not over 100Mbps SPTS Settings MPTS Settings DATA IP Settings ASI Output a Ey Channel 1 Users can copy a stream from the pe nanosi AI channel 4 IP out streams 1 MPTS amp 8 I Channel 5 Channel 6 SPTS to output through ASI channel 7 Channel 8 System Save load Clicking Save Load from the menu it will display the screen as Figure 9 s mu DE OINC y All the specifications are subject to change without any further notice All rights reserved FAdd No 10 amp No 12 Wuxing Fourth Road Wuhou District Chengdu 610045 Sichuan PR China Awww dsdvb com English WTel 86 028 85558928 Fax 86 028 85585255 Email sunyu dsdvb com 23 29 DEGING NDS3208 8 in 1 MPEG 2 Encoder Users Manual Save Configuration When you change the parameter you shoud save configuration otherwise the new configuration will lost after reboot Restore Configuration Load latest saved configuration after click the Restore then please click the Save config button otherwise the Restore parameter will lost after reboot Set Factory Set Set all configuration back to default after click the Factory Set then please click the Save config button otherwise the default parameter will lost after reboot
27. trict Chengdu 610045 Sichuan PR China Awww dsdvb com English TWTel 86 028 85558928 Fax 86 028 85585255 t amp Email sunyu dsdvb com 10 29 a parameters in the following editing interfaces the LCD will display the following pages gt System Param 2 MPTS Output Setting gt 3 Mux Setting 4 Network Setting gt 5 Config Setting 6 Version gt 7 Language 1 English 2 3 The option with BP is the current selection users can press the ENTER key to enter the specified submenu to modify the device parameter 3 2 1 System Setting Under this menu the LCD will display 8 submenus which from Encoding Channel 1 to Encoding Channel 8 The setting principle is the same for Encoding Channel 1 8 so here this manual just takes one channel as the example to explain After pressing the enter key the LCD will display the following pages gt 1 1 Channel 1 1 2 Channel 2 gt 1 7 Channel 7 1 8 Channel 8 After users enter the submenu the interface will turn into the following pages and then users can enter the corresponding interface to modify the parameters gt 1 Encoder Enable ON OFF 2 Video Param mm DE OINC 7 All the specifications are subject to change without any further notice All rights reserved FAdd No 10 amp No 12 Wuxing Fourth Road Wuhou District Chengdu 610045 Sichuan PR China Awww dsdvb com English Tel 86 028 85558928 Fax 86 028 85585255 t Email sunyu dsdvb com
28. ts BNC interface Stream output 1 MPTS 8 SPTS over UDP RIP RTSP 10 100Base T Ethernet interface uni cast multicast LCD keyboard operating Web NMS support System function Chinese English control interface Ethernet software upgrade Dimensions 482mmx455mmx44 5mm Approx weight 4Kg General Temperature 0 45 C Operation 20 80 C Storage Power AC 110V 10 50 60Hz or AC 220V 10 50 60Hz Power 17 6W a mu DE OING All the specifications are subject to change without any further notice All rights reserved lt Add No 10 amp No 12 Wuxing Fourth Road Wuhou District Chengdu 610045 Sichuan PR China Awww dsdvb com English WTel 86 028 85558928 Fax 86 028 85585255 t Email sunyu dsdvb com 2 29 DEGING NDS3208 8 in 1 MPEG 2 Encoder Users Manual 1 5 Appearance and Illustration Front Panel Illustration NDS3208 MPEG 2 Encoder a x N BENIM Indicate area All indicators will light on when the device is on the current working state a fucpsren screen a a a indicator TS in TSin inputlockindicator lock indicator Indicators CH1 CH8 When program has been multiplexed the mma will be on 3 ur DOWN LEFT RIGHT UP DOWN LEFT RIGHT keys Rear Panel Illustration AC 100V 240V 50 60Hz 2A 8 CVBS input ports mm DE Onn r AII the specifications are subject to change without any further notice All rights reserved Add No 10 amp No 12 Wuxing Fourth Road Wuhou District Chengdu 6
Download Pdf Manuals
Related Search