Hardware User Manual DEV-BF548-Lite DEV-BF548DA
Contents
1. All the Core Modules are fully supported by uClinux The required boot loader and uClinux can be downloaded from http blackfin uClinux org Upcoming Products and Software Releases Keep up to date with all the changes to the Bluetechnix product line and software updates at www bluetechnix com BLACKFIN Design Service Based on more than five years of experience with Blackfin Bluetechnix offers development assistance as well as custom design services and software development Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual BLUE Tinyboards ECHNIX maximum performance at minimum size 1 Introduction NOTE The DEV BF548DA Lite has an on board Debug Agent which is not available on the DEV BF548 Lite Board All other features are identical In this document when describing both boards the name DEV BF548 Lite is used The DEV BF548 Lite Development Board with integrated Debug Agent is designed as a development and application board for the high performance ADSP BF548 based CM BF548 Core Module Special feature of the board is the 10 100Mbit industrial Ethernet controller The integrated Debug Agent is a USB based debug interface which enables programming and debugging of the Blackfin Core Modules It is fully compatible with the Visual DSP development environment The development board provides all interfaces on dedicated connectors or expansion connectors Extender boards can be plugged on top of the Deve2. Searching for 8 bit application in flash No application found in flash Searching for BS_BOOT LDR on mass storage device No or invalid file BS_BOOT LDR was found on mass storage device Terminal ready Have a nice work LN PE Alz Connected 06 39 05 ANSTW 115200 SN SCROLL Cars NUM Capture Print echo This shows a sample boot screen Depending on the current software version you might get different boot messages 8 You can find a simple hello world program on your support CD or at the download section of the product homepage To start the sample program type xmr UART on your terminal program then Transfer gt Send file select the appropriate file UART Idr depending on your Core Module choose protocol Xmodem and send After the download has finished type exec UART for executing the sample program 9 Press reset to return to the BLACKSheep command line 7 2 Debug Agent Setup DEV BF548DA Lite only If you have purchased a DEV BF548DA Lite board with the Debug Agent mounted on the bottom side of the board you can use it to download and debug your software with the VDSP development environment from Analog Devices An evaluation version is included in the support CD or you can download it from our website or the website from Analog Devices Currently the Debug Agent works only with version 4 5 of the VDSP IDE Note The Core Module will get warm while in use Please follow the instruction
3. EN BH D 2 50 BLUE fs EEN LE ECHNIX SFE n xy a L Ps i Wm O CH oO de m N E ema m Ma O e 8 ema mu mum ON g MEE em mmm MEE em MEEN a E Iesse Esc Iesse a Ed f aen a i a aar sa I Es EER IE N mm em em ma S IT 6 RO g 9 gt gt N o 0 8 x3 2 50 2 50 31 20 KEE EEN HIDBIRDIDIRDUNININDHID UND TITTEN 3 5 Ri Kg 20 00 20 00 DEE Figure 3 3 Recommended Footprint for Extension Boards top view Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 7 BLUE Tinyboards ECHNIX maximum performance at minimum size 4 Connector Description 4 1 X4 RJ45 Ethernet Connector Signal Core Module 10 Type TX TX RX NC NC RX NC NC COIN OU BUI N FR Table 4 1 Ethernet Connector 4 2 X9 SD Card Connector bottom Mount PinNo Signal Core Module Description SD Card e O SD D CD DAT3 CLK Bi WwW N SD_CLK GN VSS2 sp DO DATO SD DI DATT 10 WP OO NO UI Table 4 2 SD Card Connector 4 3 X6 JTAG Bypass Connector The JTAG connector is compliant with any Blackfin JTAG Emulator from Analog Devices When an external JTAG emulator is attached the on board JTAG is bypassed and the external one is automatically used 4 4 X11 USB UART Connectors Connects either UARTO when S3 is in Pos 1 or UART1 when S3 is in Pos 0 to the USB Int
4. 8 Table 4 3 UAR TL additional Headers ss se idees ee ooo ee ie se ge ee es Eg go ie 9 Table 4 4 DEV board connector types eie see ee ee ee ee ee ee ee ee ee ee RR de ee ee ee EE Ee 9 IE lol CAIN Ooi Ere SE EE N EE EE ER 9 E Poor 50 6 A see EE ee EG be BG EE Ge Ge RE GR be trie rn nearer De DE 9 e de To Bo O OE EE EE N EE 11 4 8 Expansion Connector E 13 Ee der SA OS NOE EE N RE 15 aE IT oie d i EE 16 BZ TOTP VS sa rs cdc pe cscs arcade caress EE xs 16 table C oe Maodile LE D S oo ie Ee GE N Ee Ge 17 TONG 4 TEC CR EE 17 Table 5 5 LEDs for the Deb oen os sk EE ES RE De Ea EEEO 17 Tablet t ene 18 Table 9 1 Used without Extender Board 28 Table 9 2 Used with the Experimental Extender Board 28 Table 9 3 Used with the Video Extender Board 28 Table 9 4 Used with the Audio Extender Board 29 Table 9 5 Used with the Camera Extender Board ees sesse se ee ee ee ee ee RE ee ee ee ee 29 Table 9 6 Used with the Analog Digital Deal Analog Converter Extender Board 29 Table 9 7 Used with the USB ETH Extender Board 29 Table 9 8 Used with the Video and the Audio Extender Board sesse sesse ee ee 29 Table 9 9 Used with the Camera and the Audio Extender Board 30 Table 10 1 Anomalies on yY LO DOAnCS neie eege eege 31 Table 11 1 Prod ct Changes onscreen Ee DE eo EE Re EE ee se 32 TORE Ee AS leed SO E 33 Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 34
5. Bluetechnix CM BF537 New Modify Delete Delete All OK Cancel Test Help 6 Press Ok to close the VisualDSP Configurator The last step is the creation of a VDSP debug session Please follow the instructions below 1 Open the New Session Wizard from the pulldown menu of the VDSP Session gt New Session or press the New Session button on the Sesson List window that appears on startup of VDSP 2 Select the processor corresponding to your Core Module and press Next Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 24 BLUE Tinyboards ECHNIX maximum performance at minimum size Session Wizard H Select Processor Choose a target processor br Select Processor Ha ADSP BF531 Blackfin Processor 800 MMACS 52K bytes op Blackfin Processor 800 MMACS BAK bytes on Blackfin Processor 1512 MMACS 148K bytes o Blackfin Processor 500MHz 132K bytes on chi Blackfin Processor 700 MMACS 308K bytes on Blackfin Processor 100K bytes on chip memory Blackfin Proces 3 Select EZ KIT Lite and press Next Session Wizard Select Connection Type Choose the type of connection that vou would like to establish For the previously chosen processor below I T Select Connection Type Legacy target 4 Select the platform that you have created with the VisualDSP Configurator
6. Lite Hardware User Manual Page 9 BLUE Tinyboards ECHNIX maximum performance at minimum size GND Figure 4 1 Power connector To connect to X141 use a DCPP1 e g from Cliff Electronic Components 2 1mm 5 5mm 9 5mm plug to the power supply Outer contact is GND inner contact is VCC 4 9 Expansion Connectors The interface to the extender boards is grouped into three different connectors X1 X2 X3 The three tables below shows the pin out of these three connectors The column Pin No Connector shows the pin number of each connector while the column Pin No Symbol shows the pin number of the extension connector schematic symbol where the pins are numbered from to 200 The column Pin No CM represents the pin number of the corresponding signal on the Core Module 4 9 1 X2 Expansion Connector 2 Pin No Pin No Signal Signal type Pin No CM Symbol Connector Ne I O PC6 I O DI DI LO Ww LO D 3 3 PC3 I O 97 5 5 CLKOUT O 70 7 7 PA13 I O 114 8 8 PA5 I O 106 9 9 3 3V PWR 10 10 3 3V PWR dd 11 PDO I O 135 12 12 PD2 I O 137 13 13 PD4 I O 139 14 14 PD6 I O 141 15 15 PD8 I O 143 16 16 PD10 I O 145 17 17 PD12 I O 147 18 18 PD14 I O 149 19 19 PHO I O 22 20 20 PE12 I O 188 21 21 PB11 I O 130 22 22 PB9 I O 128 23 23 PE8 I O 192 24 24 PB13 I O 132 25 25 PB12 I O 131 26 26 PH1 I O 23 Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 10 BLUE Tinybo
7. O 177 74 14 PF7 I O 175 75 15 PF9 I O 173 76 16 PF11 I O 171 77 17 PETS I O 169 78 18 PF15 I O 167 79 19 GND PWR 80 20 nAMS1 O 30 81 21 nAWE O 20 82 22 nNMI 34 83 23 DO I O 35 84 24 D2 I O 37 85 25 D4 I O 39 86 26 D6 I O 41 87 27 D8 I O 43 88 28 D10 I O 45 89 29 D12 I O 47 90 30 D14 I O 49 oi 31 D15 I O 50 92 32 D13 I O 48 95 33 D11 I O 46 94 34 D9 I O 44 95 35 D7 I O 42 96 36 D5 I O 40 97 37 D3 I O 38 98 38 D1 I O 36 99 39 NRESET I O 67 100 40 nAOE O 18 101 41 nARE O 19 102 42 nAMS2 O 31 103 43 3 3V PWR 104 44 PF14 I O 168 105 45 PF12 I O 170 Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 12 BLUE Tinyboards ECHNIX maximum performance at minimum size 106 46 PF10 I O 172 107 47 PF8 I O 174 108 48 PF6 I O 176 109 49 PF4 I O 178 110 50 PF2 I O 180 111 51 PFO I O 182 112 52 PH2 I O 24 113 53 PGO I O 166 114 54 A14 O 14 115 55 A12 O 12 116 56 A10 O 10 117 57 A8 O 118 58 A6 O 119 59 A4 120 60 A2 O N B 0O O 4 8 Expansion Connector X1 4 9 3 X3 Expansion Connector 3 Pin No Pin No Signal Signal type Pin No CM Symbol Connector 121 1 GND PWR 122 2 PJ13 I O 74 123 3 PJ12 I O 75 124 4 PJ11 I O 76 125 5 PJ10 I O 77 126 6 PJ9 I O 78 127 7 PJ8 I O 79 128 8 PJ7 I O 80 129 9 PJ6 I O 81 130 10 PJ5 I O 82 131 11 PJ4 I O 83 132 12 PJ3 I O 84 133 13 PJ2 I O 85 134 14 PJ1 I O 86 135 15 GND PWR 136 16 PBO I O 119 137 17 PB1 I O 120 138 18 PB2 I O 121 139 19
8. PB3 I O 122 140 20 PB4 I O 123 141 21 PB5 I O 124 142 22 PB6 I O 125 143 23 PB7 I O 126 144 24 GND PWR 145 25 PAO I O 101 146 26 PA2 I O 103 Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual 9 DI UO CD KA LA BLUE Tinyboards ECHNIX maximum performance at minimum size 147 27 PA3 I O 104 148 28 PA4 I O 105 149 29 PA6 I O 107 156 36 PA15 I O 116 157 37 GND PWR 158 38 GND PWR 159 39 3 3V PWR 160 40 3 3V PWR 161 41 5 0V PWR 162 42 Vin PWR 163 43 GND PWR 164 44 PG3 I O 163 165 45 PG4 I O 162 166 46 PG5 I O 161 167 47 PG6 I O 160 168 48 PG7 I O 159 169 49 PG8 I O 158 170 50 PG9 I O 157 171 sy PG10 I O 156 172 52 PG11 I O 155 173 53 PG12 I O 154 174 54 PG13 I O 153 175 55 PG14 I O 152 176 56 PG15 I O 151 177 57 GND PWR 178 58 PEO I O 200 179 59 PE1 I O 199 180 60 PE2 I O 198 181 61 PE3 I O 197 182 62 PE4 I O 196 183 63 PES I O 195 184 64 PE6 I O 194 185 65 PE9 I O 191 186 66 PE10 I O 190 187 67 GND PWR 188 68 PC8 I O 92 189 69 PC9 I O 91 190 70 PC10 I O 90 t91 71 PC11 I O 89 192 72 PC12 I O 88 193 73 PC13 I O 87 194 74 PH6 I O 28 195 75 PHS I O 27 Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 14 BLUE Tinyboards ECHNIX maximum performance at minimum size 196 76 ATAPI_PDIAG 134 197 77 EXT_WAKEUP O 33 198 78 GND PWR 199 79 CLKBUF O 69 200 80 GND PWR 4 9 Expansion Connector X3 Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware
9. a size of 36 5x31 5mm Blackfin Processor Module powered by Analog Devices single core ADSP BF537 processor up to 6OOMHZz 32MB RAM 4MB Flash integrated USB 2 0 Device 120 pin expansion connector and a size of 36 5x31 5mm will be replaced by CM BF527 Blackfin Processor Module powered by Analog Devices single core ADSP BF537 processor up to 500MHz 32MB RAM 8MB Flash 28x28mm 120 pin expansion connector Ball Grid Array or Border Pads for reflow soldering industrial temperature range 40 C to 85 C Blackfin Processor Module powered by Analog Devices dual core ADSP BF561 processor up to 2x 600MHz 64MB RAM 8MB Flash 120 pin expansion connector and a size of 36 5x31 5mm The new Blackfin Processor Module is powered by Analog Devices single core ADSP BF527 processor key features are USB OTG 2 0 and Ethernet The 2x60 pin expansion connectors are backwards compatible with other Core Modules The new Blackfin Processor Module is powered by Analog Devices single core ADSP BF548 processor key features are 64MB DDR SD RAM 2x100 pin expansion connectors Low cost Blackfin processor Evaluation Board with one socket for any Bluetechnix Blackfin Core Module Additional peripherals are available such as an SD Card Get ready to program and debug Bluetechnix Core Modules with this tiny development platform including a USB Based Debug Agent The DEV BF5xxDA Lite is a low cost starter development system including VDSP Evaluation So
10. and press Finish Session Wizard Select Platform Provide a name For the session and choose the specific platform it will connect to If connecting to an emulator and do not see an appropriate platform in the list click the Configurator to create one f Ti Select Platform ADSP BF537 Bluetechnix CM BF537 D ite via Debug Agent echnix CM BF537 Show all platforms Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 25 BLUE Tinyboards ECHNIX maximum performance at minimum size Now the session is ready and VDSP should start with these settings The Core Module on the DEV BF548DA Lite is now ready for debugging For further information about the session wizard and the VDSP tools please refer to the VDSP manuals downloadable from the Analog Devices website If you change your Core Module on the DEV BF548DA Lite you have to reconfigure VDSP starting with the install tool as described above Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 26 BLUE Tinyboards ECHNIX maximum performance at minimum size 8 Using the VDSP Flash Programming Tool 8 1 Developing an Application If you are developing your own projects with the VDSP development tools using the JTAG provided by Analog Devices you can use the flash programming tool included in the VDSP environment in order to flash your program on the Core Module You have to load the flash driver
11. BLUE ECHNIX ardware User Manual DEV BF548 Lite DEV BF548DA Lite Board V1 1 Tinyboards from Bluetechnix www bluetechnix com Contact Bluetechnix Mechatronische Systeme GmbH Waidhausenstr 3 19 A 1140 Vienna AUSTRIA EUROPE office bluetechnix at http www bluetechnix com Document No 100 2246 1 0 Document Revision 11 2009 02 04 Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Table of Contents Me ie ie dio RE EE os snes oes OE EE i Mac e A E E OE A E N OE l 2 Panc onai Pe ge e E 4 3 PCB Placement and Mechanical Outlme ss sees ee ee AR Re ee ee J od NEE oanien E E E E E E E E GEE 5 3 2 Mechamcal Outline sessies a Pe EA OE EA Ie EE EES EEEE r 6 So Frensio Bodd HOO N sn ER E ed T EEES 6 EE EE 8 dl AARI Ethernet EE 8 42 X9 SD Card Connector bottom Mount 43 OIE Bypass C OC CUE seriski siener on DO Ge ee N OG ee 8 44 X11 USB UART Connectors EEN 8 As AL CUVARI E paai OM Ad ek SUE ee OR E ene Rd ED eee 9 4 6 X1 X2 X3 Expansion ConnecCtOrS iss ese ee ee ee ee RR ee ee ee ee EE Ee 9 4 7 X8 X10 CAN1 CANO Connector ss sesse soe ee ee ee ee ee ee ee ee ee ee 9 As epiteel E 9 AS EIS ION EE eege 10 491 X2 Expansion ent 10 4 9 2 e Expansion Connector EE 12 49 3 X3 Expansion Connector Eet 13 gt Switches Jamper and LED DeseripUOR es ses ser eed sd ee N dee be Ge ek ee de n ie se ee 16 Del RESO E 16 5 2 S2 Ethernet Control Signals SDCARD Ch 16 Be B
12. ERT e EE 16 Zo SFBO COn MOE Oo OE et VR EE OE EE N rr ere 16 Ik dPLsEihernelt Speed Te EE 16 39 JP2 POW Cr SUP DIY ne 16 560 JP3 RTC Power ME Us EA OE ON EO N EE OE EE ON 17 I B a UD EE ee ee eee ee 17 e EE TO EEN 17 II Meme ral Purpose LERE RE EN De EE ed De DO Ee de ee Dr ee 17 IAO Eilieraet LE DS ie Ed EE E De ea De EE GE eaters 17 il 1EDSGFiEDEbAE APE oi esse Ge Ro GE EE Ee AE Ee ee EE EE 17 6 Boet Mode CSCO E 18 Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual T OS die EE 19 Tod Tuil Board SC OER OE EE EE OE EE TE 19 7 2 Debug Agent Setup DEV BF548DA Lite only G 8 Using the VDSP Flash Programming Tool 21 8 1 Developing an Application cccccccccccccssssssseeccccccceeeesseeecceeeesssaeaseeeeeeseessaaaeasseeeeess Pd 62 Overwiriting BLACK sheep Code sedes Ego seke SR BG ee ee SE EN GES ee 27 9 Extender Board Compatibility E ee Re DE EE a re 28 CSN Ter E onder BO ME 28 EN dio EA P e EE E 28 EN TEE 1 EE 28 9 4 Audio Extender Board gege esse esse ses ie ese se es de es ee se rn diens es Ee 29 Emmer F dender Bod as EE ee ee ed ee ee ed ee ee 29 9 6 Analog Digital Deal Analog Converter Extender Board 29 27 USB EIH Extender Bodd ss ie iese ie oe de De Ee ew ee Ge oe Di ee eie 29 Oro GREEN Andio Extender Dodd DoE EG EO Ge Ee DE 29 9 9 Camera and Audio Extender Board 30 O ii AE EE RE ER EE EN 31 MM OG us ER AE OE OR OR N dens 32 IZ Document Revision HIStory asses dsns e SE AER a GE a
13. PORT3 o CANO CANI o UART 2 UART3 o PPIO Sync D16 D17 o SDIO Interface o GPIO Programmable Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 2 BLUE Tinyboards ECHNIX maximum performance at minimum size USB2 0 OTG Connector o Uses the On Board USB OTG transceiver RJ 45 Ethernet Plug o Connected to the On Board SMSC LAN9218 Ethernet Controller External Power Supply o The board is shipped with a 12V 2A external DC DC Power Supply Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 3 BLUE Tinyboards ECHNIX maximum performance at minimum size 2 Functional Specification X1 Data amp Addr Bus Mem Control PPIO GPIO Button Power Power LED Reset Connector cof DC DC 3Vv3 RJ 45 USB Device Power Supply 10 100Mbit Ethernet Connector L L Ethernet Connector USB UART Controller USB UART Converter CM BF548 USB OTG Connector Expansion LI USB UART uart 64MB DDR SD RAM JTAG SD Card Switch S3 8MB Flash Bypass Connector _____SD IO Debug Agent USB CAN LC Mag Connector LT Trasceiver Connector 80 60 X3 ATAPI SPI0 1 SPORT2 3 CANO 1 UART2 3 SD IO GPIO X2 PPI1 SPORT1 SPORTO UARTO SPI2 GPIO Figure 2 1 Functional Block Diagram Power connecto
14. User Manual Page 15 BLUE Tinyboards ECHNIX maximum performance at minimum size 5 Switches Jumper and LED Description 5 1 S1 Reset switch Performs system reset 5 2 S2 Ethernet Control Signals SDCARD CS EE On Won A Default Settings Dipswitch Function KEN Connect SDCARD CS to PC5 2 2 Connect nAMS1 from Core Module to Ethernet chip 2 3 Connect PE6 from Core Module to Ethernet chip IRQ S2 4 Connect PME of Ethernet chip to test point PME1 5 1 DIP switch S2 S3 UART Switch Move S3 to position to route the Core Modules RX0 and TXO signals to USB Move S3 to position 0 to route the Core Modules RX1 and TX1 signals to USB 5 3 S4 Boot Configuration S4 1 to 4 4 Control the boot mode and are described in chapter 6 Boot Mode Description Dipswitch Function S4 6 Power Supply for CAN1 Driver IC S4 7 Connect TXD USB to VCC 4 8 Connect S5 to VCC 5 2 DIP switch S4 5 4 JP1 Ethernet Speed Selection Set jumper JP1 to select Ethernet Speed 1OMBit s and unset JP1 for 1OOMbit s 5 5 JP2 Power Supply Jumper This jumper can be removed in order to insert an AMPERE METER for current measurement Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 16 BLUE Tinyboards ECHNIX maximum performance at minimum size 5 6 JP3 RTC Power Jumper This jumper is used to connect the VddRTC pin of the Core Module to 3 3V You can also use this jumper to connect a ba
15. ard only if he has the qualification More information is found in the General Terms and Conditions AGB Information For further information on technology delivery terms and conditions and prices please contact Bluetechnix http www bluetechnix com Warnings Due to technical requirements components may contain dangerous substances The Core Modules and development systems contain ESD electrostatic discharge sensitive devices Electro static charges readily accumulate on the human body and equipment and can discharge without detection Permanent damage may occur on devices subjected to high energy discharges Proper ESD precautions are recommended to avoid performance degradation or loss of functionality Unused Core Modules and Development Boards should be stored in the protective shipping package Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual BLACKFIN Products Core Modules CM BF533 CM BF537E CM BF537U TCM BF537 CM BF561 CM BF527 CM BF548 Development Boards EVAL BF5xx DEV BF5xxDA Lite Blackfin Processor Module powered by Analog Devices single core ADSP BF533 processor up to 600MHz 32MB RAM 2MB Flash 120 pin expansion connector and a size of 36 5x31 5mm Blackfin Processor Module powered by Analog Devices single core ADSP BF537 processor up to 600MHz 32MB RAM 4MB Flash integrated TP10 100 Ethernet physical transceiver 120 pin expansion connector and
16. ards ECHNIX maximum performance at minimum size 36 36 nABEO O 16 37 37 PB14 I O 133 39 39 PB8 I O 127 40 40 PB10 I O 129 41 41 PE11 I O 189 42 42 PE13 I O 187 43 43 PD15 I O 150 44 44 PD13 I O 148 4 PD11 I O 1 5 45 46 47 47 PD7 I O 142 49 49 PD3 I O 138 51 51 GND PWR 53 53 PA1 I O 102 55 55 PH3 I O 25 6 56 186 5 PE14 I O 57 57 Pel I O 99 59 59 PC5 I O 95 60 60 PC4 I O 96 4 7 Expansion Connector X2 1 Maximum current carrying capacity 1A 2 Pin 29 and 30 of the X8 connector are 5V stabilized from the DC DC that can be used for custom add on boards or the extender boards Maximum current carrying capacity 900mA Attention If Core Modules with USB in host mode are used the current must be shared with the connected USB device 3 Pin 31 and 32 of the X7 are Vin of the external power supply minus the input protection diode voltage These pins can be used for custom add on board power supplies Maximum current carrying capacity 1A Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 11 BLUE Tinyboards ECHNIX maximum performance at minimum size 4 9 2 X1 Expansion Connector 1 Pin No Pin No Signal Signal type Pin No CM Symbol Connector 61 1 Al O 62 2 A3 O 63 A5 O O NOWA a On TERN U A W gt gt WON OO O 6 nn N ONO gt gt A L WIP O e W e 68 A15 O 15 69 9 PG1 I O 165 70 10 PG2 I O 164 S 11 PET I O 181 72 12 PF3 I O 179 73 13 PF5 I
17. e 33 A By S00 Me Fiouies id KE 34 Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Packing List The DEV BF548DA Lite and the DEV BF548 Lite Board Package contain the following items 1 DEV BF548DA Lite or DEV BF548 Lite Board 2 1x USB Cable USB A B 3 1x USB Cable USB A B DEV BF548DA Lite only 4 1x USB Cable USB A Mini USB 5 1x Ethernet Cable 6 1x Power Supply 7 Support CD Note The Core Modules are not shipped with the board so you must order them separately Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Edition 2007 02 Bluetechnix Mechatronische Systeme GmbH 2007 All Rights Reserved The information herein is given to describe certain components and shall not be considered as a guarantee of characteristics Terms of delivery and rights of technical change reserved We hereby disclaim any warranties including but not limited to warranties of non infringement regarding circuits descriptions and charts stated herein Bluetechnix makes and you receive no warranties or conditions express implied statutory or in any communication with you Bluetechnix specifically disclaims any implied warranty of merchantability or fitness for a particular purpose Bluetechnix takes no liability for any damages and errors causing of the usage of this board The user of this board is responsible by himself for the functionality of his application He is allowed to use the bo
18. e the driver for MAC and LINUX are available on the CD In order to set up und test your DEV BF548 Lite board the following steps can be done 1 Make sure jumpers JP2 and JP3 are set and the Switch S3 is in Position 1 as shown in Figure 7 1 JP1 unset Console N USB Connector SW es Power Cable Red 6V to 12V Black GND Figure 7 1 Setup of the DEV BF548 Lite Board 2 If you want to use an SD Card insert the SD Card in the appropriate slot at the bottom side of the board 3 Connect the power supply to the power connector off the DEV BF548 Lite board 4 Connect the DEV BF548 Lite Board via USB to the PC The _ pre flashed BLACKSheep starts and the LED mounted on the DEV BF548 Lite board starts blinking On the PC usually the Found New Hardware Wizard opens Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 19 BLUE Tinyboards ECHNIX maximum performance at minimum size Found New Hardware Wizard Welcome to the Found New Hardware Wizard Windows wall search for curent and updated software by looking on Your computer on the hardware installation CD or on the Windows Update Web site with your permission Head our privacy policy Can Windows connect to Windows Update to search for sottware Yes this time only Yes now and every time connect a device Ce No not this time Click Next to continue If the wizard asks you to connect to the windows u
19. ed with the Video Extender Board Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 28 Table 9 4 Used with the Audio Extender Board 9 5 Camera Extender Board Table 9 5 Used with the Camera Extender Board Tinyboards BLUE ECHNIX maximum performance at minimum size 9 4 Audio Extender Board 9 6 Analog Digital Digital Analog Converter Extender Board Table 9 6 Used with the Analog Digital Digital Analog Converter Extender Board 9 7 USB ETH Extender Board Table 9 7 Used with the USB ETH Extender Board 9 8 Video and Audio Extender Board Table 9 8 Used with the Video and the Audio Extender Board Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 29 BLUE Tinyboards ECHNIX maximum performance at minimum size 9 9 Camera and Audio Extender Board Table 9 9 Used with the Camera and the Audio Extender Board Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 30 BLUE Tinyboards ECHNIX maximum performance at minimum size 10 Anomalies Missing pull up resistor on nBR gt workaround done I Missing pull up resistor on CMD_OD gt workaround done Table 10 1 Anomalies on V1 0 boards Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 31 BLUE Tinyboards ECHNIX maximum performance at minimum size 11 Product Changes Bug Fix and Connector Replacement inal Board Venton Table 11 1 Pr
20. erface enabling a COM Port on the PC UARTO is standard console IO for the BLACKSheep Software Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 8 BLUE Tinyboards ECHNIX maximum performance at minimum size 4 5 X12 UART Expansion Pads When S3 is in position 1 the UARTI on PortH TX RX is available on the expansion pins and disconnected from the USB UART Chip Pin No Signal Signal Type 1 TxD Blackfin Input Core Module RxD Blackfin Output Core Module GND 3V3 Regulated Power Table 4 3 UARTI1 additional Header 4 6 X1 X2 X3 Expansion Connectors The Expansion Connectors on the DEV BF548 Lite for a Stacked Height of 16mm are of the following type Part Manufacturer Manufacturer Part Nr X1 X2 AMP Stacked Height 16mm 5 5179010 2 Matching connector AMP 5179031 2 X3 AMP Stacked Height 16mm 5 5179010 3 Matching connector AMP 5179031 3 Table 4 4 DEV board connector types The matching connector which is used for building an extender board can be ordered from Bluetechnix 4 7 X8 X10 CAN1 CANO Connector Pin No Signal Core Module O Type 1 CAN I O 2 CAN I O Table 4 5 CAN Connector 4 8 X5 Power Connector The board is shipped with a 12V 2A external DC DC Power Supply which should be used Pin No Signal Description Vin 6V to 16V DC Input Supply Preferable 12V DC 2A 1 3 GND Table 4 6 Power Supply Blackfin DEV BF548 Lite amp DEV BF548DA
21. formance at minimum size 3 PCB Placement and Mechanical Outline 3 1 PCB Placement X5 X7 X6 X13 X11 Power USB JTAG Ext JTAG USB OTG USB UART S4 JP4 MEE X12 P 3 iit ft et 1 8 Al som 3 Er g ON Se d X10 CANT X1 X2 31 30 31 30 X8 CANO S2 1 40 muuu 1 60 1 60 1 o 80 a 41 1 i 40 X9 A SD CARD J X4 Ethernet JACK Corner holes on Core Module indicating insertion Rotation Figure 3 1 Connector PCB Placement Please mind the direction while inserting the Core Module Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 5 BLUE Tinyboards ECHNIX maximum performance at minimum size 3 2 Mechanical Outline Ui LL bl uetechnix com amma aiian det RxD RED uuutt E pe Tout TxD R42 3U3 SU ILL MI Jeck x12 Mi WW n am mi o ws Eg 9 atl R45 N R24 f 90 00 100 00 D 50 00 x2 25 00 30 00 20 00 20 00 30 00 100 00 Figure 3 2 Mechanical Outline Expansion Connector Placement 3 3 Extension Board Footprint If you want to design your own Extension Board for the DEV BF548 you can use the following Board dimensions The mating Connectors in Figure 3 3 are mounted on top Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 6 BLUE Tinyboards ECHNIX maximum performance at minimum size 100 00 5 00 Oo e i 1 2 x3 0 50 N
22. ftware License Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual DEV BF5xx FPGA DEV BF548DA Lite EXT Boards Software Support BLACKSheep LabVIEW uClinux Blackfin Development Board with two sockets for any combination of Blackfin Core Modules Additional peripherals are available such as SD Card Ethernet USB host multi port JTAG including a USB based Debug Agent connector for an LCD TFT Display and connector for a digital camera system A large on board SPARTAN 3 FPGA and Soft IPs make this board the most flexible Blackfin development platforms ever developed Get ready to program and debug Bluetechnix CM BF548 Core Module with this tiny development platform including a USB Based Debug Agent The DEV BF548DA Lite is a low cost starter development system including VDSP Evaluation Software License The following Extender Boards are available EXT BF5xx Audio EXT BF5xx Video EXT BF5xx Camera EXT BF5xx Exp EXT BF5xx ETH USB EXT BF5xx AD DA Additional boards based on customer request are also available The BLACKSheep VDK is a multithreaded framework for the Blackfin processor family from Analog Devices that includes driver support for a variety of hardware extensions It is based on the real time VDK kernel included within the VDSP development environment LabVIEW embedded support for the CM BF537E CM BF537U and TCM BF537 Core Modules is based upon the BLACKSheep VDK driver Framework
23. located on your EVAL board support CD corresponding to the inserted Core Module 8 2 Overwriting BLACKSheep Code If you overwrite intentionally or unintentionally the section in the flash containing the BLACKSheep code you need a JTAG device and the VDSP flash tool to reprogram the flash Flashing the appropriate BLACKSheep loader file ldr located on the CD reinstalls the BLACKSheep code The examples drivers and the BLACKSheep software are under permanent development Please refer to the download section of www bluetechnix com to get the latest versions or updates Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 27 BLUE Tinyboards ECHNIX maximum performance at minimum size 9 Extender Board Compatibility List This chapter points out the compatibility of the DEV BF548 Lite and DEV BF548DA Lite with Core Module and Extension Boards Please refer to the Extender board and Core Module Hardware Manuals for further information Legend Full functional Functional but not all features are available Not functional Functionality not guaranteed Not tested yet Limited The following tables show possible board combinations 9 1 Without Extender Board EEN o o Table 9 1 Used without Extender Board 9 2 EXT BF5xx EXP Table 9 2 Used with the Experimental Extender Board All boards can be used in combination with the Experimental Extender Board 9 3 EXT BF5xx Video Table 9 3 Us
24. lopment Board in order to enable additional interfaces 1 1 Overview The DEV BF548 Lite Board includes the following components 60 Pin Expansion Connector 1 USB to DC DC Power Supply UART 5V and 3V3 DEBUG CM BF548 AGENT USB OTG 64MB DDR SD RAM 8MB Flash SD Card 10 100Mbit Ethernet CAN Controller cD O O oO c G O O Ke Sa D O X lt LU E A O OO 60 Pin Expansion Connector 2 Figure 1 1 Overview of the DEV BF548 Lite Board DC DC Converters o 5V 2A o 3V3 1 5A draws its power from the 5V output of the DC DC 1 Core Module Slot o Supports the CM BF548 Core Module USB to UART Port Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 1 BLUE Tinyboards ECHNIX maximum performance at minimum size o Supports up to 915kbps UART USB conversion o Emulates a standard COM port on the computer o Drivers for Windows and Linux available s JTAG o JTAG Plug that supports all analog Devices JTAG Emulators Expansion Connector 1 X1 o Data Bus o Address Bus o Memory Control o RESET o PPIO Parallel Port Interface 0 o GPIO Programmable o Power Supply Expansion Connector 2 X2 o PPI Parallel Port Interface 1 SPORT o Power Supply Main Supply Connector o GPIO Programmable o UARTO o SPI2 Expansion Connector 3 X3 o ATAPI Interface o SPIO SPII o SPORT2 S
25. ndows device manager Control Panel gt System 2 Hardware to see which COM port number has been assigned to the CP2101 UART to USB Chip This number differs from computer to computer based on the already installed COM ports e g COMA4 6 Open a Terminal program like the HyperTerminal included in Windows operating systems and open the respective COM port with 115200 Baud 8 Data bits No Parity and 1 Stop bit disable the Hardware flow control 7 Reset the DEV BF548 Lite Board Press the main reset button After this you will see the BLACKSheep boot screen showing up If you disconnect the device you have to reconnect Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 21 BLUE Tinyboards ECHNIX maximum performance at minimum size com_1 HyperTerminal III x File Edit wiew Call Transfer Help Dis 213l Checking for SD cards Checking slot Card found Checking card D card Command response SD card Product name SD256 D card Manufacturer ID 2 sD card Application ID TM D card Product revision Hz D card Serial number 2133584913 D card Manufacture month 11 sD card Manufacture year 2004 SD card Card Status D card Size in kb 2527160 D card Checking card for filesystem Error B Found Filesystem FAT16 Partition mounted as sdBa Checking slot 1 No or illegal card found Error 1 Last address of BLACKSheep Ox2002811c Searching for 16 bit application in flash
26. oduct Changes Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 32 BLUE Tinyboards ECHNIX maximum performance at minimum size 12 Document Revision History Version Date Document Revision 1 2009 02 04 Caption for some tables added Table 5 1 corrected Table 6 1 S4 4 S4 1 added 2008 10 15 Chapter 4 9 column Pin No Symbol added A 2008 09 23 Extension Footprint added Layout changed 8 2008 08 18 English checked for grammar spelling and clarity Change matching connector 6 2008 06 26 Fixed naming of dipwitches and added missing ones 2008 05 29 VDSP Version 2008 05 23 Several changes 4 2008 04 01 Extender Board Compatibility List 2 2007 12 10 Minor Changes 2007 12 09 Initial release of the document Table 12 1 Revision History Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 33 BLUE Tinyboards ECHNIX maximum performance at minimum size A List of Figures and Tables Figures Figure 1 1 Overview of the DEV BF548 Lite Board l Fisore 2 1 Functional Block Dia graf sees esse oe dee ed be ke we ee De se De A Pieure 5 1 Connector EIERE ER 5 Figure 3 2 Mechanical Outline Expansion Connector Placement iis ss ee ee 6 Figure 3 3 Recommended Footprint for Extension Boards top view 7 Figure 7 1 Setup of the DEV BF548 Lite Board ees ese es 19 Tables Table sd Fiieriier EE EE 8 MAIC Zs SD Card e e ET
27. pdate site select No not this time Found New Hardware Wizard This wizard helps vou install software for CP2101 USB to UART Bridge Controller If your hardware came with an installation CD IE or floppy disk insert it mow What do you want the wizard to da Install the software automatically Recommended Click Next to continue lt Back Cancel Choose Install from a list or specific location The driver is located on your support CD Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 20 BLUE Tinyboards ECHNIX maximum performance at minimum size Found New Hardware Wizard Please choose your search and installation options Sa Search for the best driver in these locations Use the check boxes below to limit or expand the default search which includes local paths and removable media The best driver found will be installed T Include this location in the search Browse C Don t search will choose the driver to install Choose this option to select the device driver From a list Windows does not guarantee that the diver you choose will be the best match for your hardware Back Cancel This procedure has to be done twice because at first the USB driver will be installed Then the Hardware Wizard opens again because the UART bridge driver has to be installed in addition using the same driver file Simply repeat this step 5 Open the Wi
28. r and Power supply The supplied power supply should be used It can deliver up to 2A at 12V The input voltage range of an alternative power supply must be between 6 16V The on board DC DC power supply generates 5V and 3 3V which are made available at the expansion connectors The maximum current that can be drawn from the 5V is 2A but take care this includes the current going into the 3 3V regulator also because this regulator is powered by the 5V The maximum current that can be drawn from the 3 3V is 1 5A but note that this means at least 1A additional load on the 5V connector The serial Port O UARTO default Console IO or Port UART1 of the Core Module can be routed directly to the USB Port USB UART Switch S3 An Ethernet controller SMSC LAN9218 is connected to the data and address bus on the baseboard providing a high speed 10 1OOMBit LAN Interface An SD Card connector is mounted on the board and is connected to the processors SD IO Interface With the SD Card one can make use of file IO Functions delivered with the BLACKSheep Software BLACKSheep supports SD Cards and includes a FAT file system as well as the most relevant File IO Functions The complete BLACKSheep software package can be purchased from Bluetechnix The USB2 0 OTG connector interfaces with the processors on chip ADSP BF548 USB Transceiver Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 4 BLUE Tinyboards ECHNIX maximum per
29. ructions on the screen Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 23 BLUE Tinyboards ECHNIX maximum performance at minimum size After the install process you have to create a Platform using the Platform Wizard of the VDSP Please follow the instructions to create a valid Platform for the Bluetechnix USB Debug Agent 1 Open the VisualDSP Configurator from the start menu entry of VisualDSP 4 5 2 Select New 3 In the Type box select the Bluetechnix entry corresponding to the Core Module on your DEV BF548DA Lite board 4 Enter a Name for the Platform for example Bluetechnix CM BF537 Platform Properties 7 x Platform Devices Hame Bluetechnix CM BF537 mall Devices listed in sequential order from TOO to TDI d Mew Device D Moto Delete Delete Al l BaTS1015 USB EZ KIT CPLD Address D400 i p Doan Cancel 5 Select Ok The created platform should appear in the Platforms section of the configurator window 3 YisualDSP Configurator E KIES Platform Templates Platforms HF ADSP 21065L EZ KIT Lite Aig ADSP 21160 EZ KIT Lite Biv ADSP 21161 EZ KIT Lite HR ADSP 21262 EZ KIT Lite Biv ADSP 21364 EZ KIT Lite Ai ADSP 21369 EZ KIT Lite Aig ADSP BF533 EZ KIT Lite Ai ADSP BF535 EZ KIT Lite Biv ADSP BF537 EZ KIT Lite Aig ADSP BF561 EZ KIT Lite A ADSP TS101 EZ KIT Lite A ADSP TS201 EZ KIT Lite B
30. s for installing and configuring VDSP to work with the Debug Agent 1 Install VDSP 4 5 2 If available install the latest update for VDSP 4 5 You can download updates from the Analog Devices website Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 22 BLUE Tinyboards ECHNIX maximum performance at minimum size 3 Configure VDSP 4 5 to support the DEV BF548DA Lite by starting the Installer from your support CD Once started you should see the following dialog Note To run the installer the net framework is required 4 Select the Core Module that you have inserted in the socket of your DEV BF548DA Lite 5 Press the Install button 6 You should get the following message CS 8 l KA i 1 VOSP 4 4 5 successfully configured 7 Be sure that the board is powered on 8 Connect X4 USB JTAG with an USB cable to a free USB port on your PC 9 The following dialog or a similar one should appear Found New Hardware Wizard Welcome to the Found New Hardware Wizard This wizard helps you install software for USB Device If your hardware came with an installation CD EP or floppy disk insert it now What do you want the wizard to do Install the software automatically Recommended Install from a list or specific location Advanced Click Next to continue 10 Choose Install the software automatically press Next and follow the inst
31. ttery to the internal RTC of the Blackfin 5 7 JP4 USB ID Short jumper JP4 to tie USB ID to GND on the USB OTG Connector X13 5 8 S5 Button The button S5 is a GPIO Button and connects to PH7 5 9 General Purpose LEDs Designator Function Blackfin GPIO V14 GPIO LED PH6 V15 GPIO LED PH5 Table 5 3 Core Module LEDs 5 10 Ethernet LEDs Designator Color Description Yellow Fullduplex Activity 100MB Speed LED Table 5 4 Ethernet LEDs 5 11 LEDs of the Debug Agent Designator Description Monitor Pr done Table 5 5 LEDs for the Debug Agent Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 17 BLUE Tinyboards ECHNIX maximum performance at minimum size 6 Boot Mode Description Boot settings for CM BF548 S4 only Switches 1 4 of 8 are shown _ RAT AE On GEET Of 123 45 6 7 8 The default Boot Mode option for the BLACKSheep Software is 0001 The default Boot Mode option for the uClinux uBoot is 0001 BMODE3 0 S4 4 S4 1 Description 0000 Idle no boot 0101 Boot from serial TWI memory EEPROM flash 1111 Boot from 8 Bit Host DMA Table 6 1 Boot modes Blackfin DEV BF548 Lite amp DEV BF548DA Lite Hardware User Manual Page 18 BLUE Tinyboards ECHNIX maximum performance at minimum size 7 Installation 7 1 Initial Board Setup The installation guide is written for Windows Windows 2000 and WinXP However for connecting the USB devic
Download Pdf Manuals
Related Search