Home

User Manual - I

1. 14 3 Connect the PS 2 keyboard and mouse connectors of the KVM cable set to the second stage Switch s console keyboard and mouse ports Note The above working diagram represents an JKP1610LS 16 KVM switch cascaded with the 115 801 17 1 KVM switch 4 Using the all in one KVM Cable set Part No K15C6P take the male HDDB 15pin connector and plug it into the PC1 port indicated on the rear of the second stage switch Connect the other male VGA HDDB 15 cable end to the VGA port of the computer you re installing 5 Connect the PS 2 keyboard and mouse connectors of the KVM cable set to the corresponding keyboard and mouse ports on the computer 4 4 4 45 5 E 6 Repeat steps 2 and 3 for any other compatible KVM switches you wish to add to the installation Then repeat steps 4 and 5 for each additional computer you wish to connect 15 Connecting the Power Supply 1 Connect the power cord to the power jack on the rear of the JKP1 KVM switch Then plug the power cord into an available power outlet For all KVM switches attached connect in turn the DC 9V 600mA power adapter to the power jack on the rear of each switch g 2 Power on all computers Perform a Manual Reset of the Master KVM switch by pressing the Port 1 and Port 2 manual push button selectors simultaneously for 2 seconds All port LEDs of the Master switch will flash green for re
2. To access computers of the Slave Switch 1 Invoke the Hot key mode by pressing the SCROLL LOCK key twice within two seconds 2 SPACE 3 In the OSD of the Master Switch move the highlight bar to the cascaded port shown with an symbol NAME PWR Port 1 COMPUTER1 5 E 0 1 2 COMPUTER 2 0 2 3 3 0 3 5 COMPUTER 5 0 5 6 COMPUTER 6 0 6 7 COMPUTER 7 0 7 1 1 1 4 COMPUTER 4 0 4 1 1 1 COMPUTER 8 1 0 8 HOME MASTER ENTER SELECT 1 UP DOWN INS RENAME SPACE SPACE ADMIN ESC EXIT 23 According to the previous OSD port 1 of the Master Switch is cascaded In order to access the Slave Switch move the highlight bar to port 1 and press ENTER to access the slave switch 4 Press SCROLL LOCK key twice within two seconds 5 SPACE 6 Move the highlight bar from 1 to 8 to select the desired computer and press ENTER NAME PWR 1 COMPUTER 2 COMPUTER2 5 3 COMPUTER3 4 COMPUTER4 5 COMPUTER 5 6 COMPUTER 6 X 7 COMPUTER 7 8 COMPUTERS Ag a9 b ENTER SELECT L UP DOWN INS RENAME SPACE SPACE ADMIN ESC EXIT Note the JKP1 series is designed for 2 levels of cascading only Returning to the Master Switch Using OSD 1 Invoke the Hot key mode by pressing the SCROLL LOCK key twice within two seconds 2 SPACE 3 Key in Home Note Afte
3. um 32 LCD FLAT PANEL DIPSLAY Panel Controls and OSD Functions POWER Press MENU Button display will show following picture Continue to press and e button to select function Then press SEL to enter these functions and adjust them to your personal Auto Auto Brightness Contrast Horizontal Vertical Color OSDHP OSDVP OSD Time Language Recall Exit Power On Off switch Soft power on off button Adjacent LED is lit when on Auto Auto synchronize and scale down display to any valid factory preset timings l9 Press to scroll the function you want to adjust Press to scroll the function you want to adjust Menu To access the main menu This button also acts as the Enter button Auto tracking positioning phase and size 1 Press the Menu button 2 Usethe and e button to scroll 33 Brightness Contrast Horizontal Vertical Color OSDHP OSDVP OSD Time Language Recall Exit 3 Press the SEL button to enter 4 Use the LOK and button to adjust the brightness of the display 5 Press the SEL button to go back to main menu Brightness Adjust LCD brightness level 0 255 of the image 1 Press the Menu button Use the e and amp button to scroll 2 Auto Contrast Horizontal Vertical Color OSDHP OSDVP OSD Time Language Recall Exit 3 Press the SEL button to enter 4 Use the and button to adjust the brightness
4. JKP115 1601e 117 1601e port JKP1 series leverages the power of existing server networks with minimal intrusion Highly efficient it allows centralized access and control of up to 128 256 computers via Cascading from an integrated 1U console drawer with built in 15 17 LCD display 8 16 port KVM switch keyboard and touchpad JKP1 KVM series is designed to deliver considerable return on investment saving time money and valuable server room real estate it can be rack mounted at any user height With a host of advanced features designed to protect your investment the series includes intelligent OSD On Screen Display menus Hot Key switching Auto sensing of cascade computers Quick View scanning and Firmware upgrades Whether it s in educational government or corporate sectors the JKP1 series provides network managers and IT managers a stable management tool for consolidated server access and control 1 APPLICATIONS The JKP115 801eJKP1 117 801e 115 1601eJKP1 117 1601e switch offers IT managers and MIS staff consolidated control of hundreds of computers via a single integrated console Applications include ISPs IDCs Data centers amp server firms Test labs OVERVIEW OSD On Screen Display An intelligent menu system designed to easily access and control multiple servers Hot Keys Hot keys allow you to use designated key commands to switch computers Control multiple computers using a simple hot
5. Hot Key Set Password Change Password wn D o cm 2 SR RE RE RRR aagal 5158 ale Eeee goc ee e SEE E ERR RR RR IERRA M s E m 5 15 5 Note 1 The SCROLL LOCK key must be pressed within 2 seconds 2 The Shift key can be another Hot Key choice 3 You will find that after the KVM unit switches to another computer there is a mouse keyboard delay of 1 2 seconds This is normal and ensures re synchronization of the console and connected computers 20 OSD OPERATION The On Screen Display OSD is an intelligent menu system designed to help administrators set up and easily access and control a multiple server installation The menu driven interface consists of a main Overview menu and an Administrative sub menu from which users can perform multiple tasks from naming servers to configuring operations The superimposed OSD overlay screen is generated by the Switch and does not affect your computers or software in any way OSD Overview Menu The main On Screen Display OSD menu can be accessed by doing the following 1 Press the SCROLL LOCK key twice followed by the Space bar The OSD overlay screen appears NAME PWR Port 1 COMPUTER1 E 0 1 2 COMPUTER2 0 2 3 COMPUTER3 0 3 4 COMPUTER 4 0 4 5 COMPUTER 5 0 5 6 6 0 6 7 7 0 7 8 COMPUTERS 0 8 HOME M
6. OSD OPERATION ra nta P21 FIRMWARE UPGRADES sess nnns P26 JKP115e 117e LCD CONTROL CONSOLE OVERVIEW FEATURES teer dea ly P28 iet three et P28 SPEGIEIGATIONS edt reb mete P29 DISPLAY DIAGRAMS etate decia int eet oce ted ea erue apes de P30 HARDWARE eene nnne P31 LCD DISPLAY CONTROLS AND P33 FCC a oaen P36 ABOUT THIS MANUAL Document Conventions This manual uses different formats to quickly identify information Indicates keyboard selection E g Ctrl 8 indicates you should press the Control key followed by the numeral 8 Sequenced keys appear with a comma between them Ctrl Ctrl Bulleted information 1 Numbered lists designate sequenced instructions indicating important information Italics Italics Represents text given in reference or as example D Important Information Please have the following information ready beforehand Your current computer installation operating system configuration details software etc e Error messages reports or other information that may assist our staff INTRODUCTION Thank you for purchasing VeloxView LCD Console KVM server management solution Designed for IT professionals the 8 JKP115 801e 117 801e and 16
7. TECH COMPANY 8 16 Port LCD KVM Switch JKP115 801e 117 801e JKP115 1601e 117 1601e LCD Control Console JKP115e 117e User Manual TABLE OF CONTENTS JKP115 8016 117 801e amp JKP115 16016 117 1601e LCD KVM SWITCH MANUAL CONVENTIONS essen nnne P1 TECHNICAL SUPPORT notet ertet toten hh S P1 INTRODUCTION triti teinte nne ehe retenir te eret tbe rendus P1 eee ees P2 OVERVIEW xcti tern eese Ir ee PEE RR P2 FEATURES iip qi oto mise iac na cb Aa P3 PACKAGE CONTENT S P4 EQUIPMENT 5 emen enn P4 SPECIFICATIONS pistes diente eee te EE ds P5 DISPLAY DIAGRAMS emen nennen P6 INSTALELATION centri te tenete ehe eerte es P8 HARDWARE INSTALLATION nnns P9 LCD DISPLAY CONTROLS AND FUNCTIONS e P10 SINGLE SWITCH INSTALLATION ssseseeeee nnn P13 MULTIPLE STAGE CASCADING P14 CONNECTING EXTERNAL MOUSE sess enne enne P14 OPERATION rectc seen nina dai rn P17 HOT KEY OPERATION rt tria P17 PORT IDENTIFICATION ene e ehe P17 PORT SELECTION 22 1 nente itd ere tee eee tete ane P18 QUICK VIEW SCAN eene eene P19 PASSWORD SECURITY LOCKING SERVER ACCESS sse P19 BEEPER CONFIRMATION 2 2 ftt dft dette P19 HOL KEY SUMMARY ud erede n ecrire be rere eei P20
8. of the display 5 Press the SEL button to go back to main menu Contrast Adjust white color level 0 255 of the image 1 2 Press the Menu button Use the and button to scroll Auto Brightness Horizontal Vertical Color OSDHP OSDVP OSD Time Language Recall Exit Press the SEL button to enter Use the and button to adjust the brightness of the display Press the SEL button to go back to main menu 34 Horizontal Adjust LCD display horizontal level 0 255 Vertical Adjust LCD display vertical level 0 255 Recall Adjust LCD setting back to previous setting Color ICON 9300 To set CIE coordinate at 9300 color 6500 To set CIE coordinate at 6500 color Gain R G B 0 255 Offset R G B 0 255 OSDHP Adjust OSD horizontal level 0 255 OSDVP Adjust OSD vertical level 0 255 OSD TIME Adjust OSD time 5 60 seconds Language Chinese English Recall Adjust LCD setting back to previous setting Power Indicator ON ORANGE STANDBY ORANGE SUSPEND 35 FCC CERTIFICATIONS This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed
9. the port ID 05 Press SCROLL LOCK SCROLL LOCK 05 Multiple Switch Installation Cascade Port number m i gt PortiD 0008 PortiD 0006 PortiD 0004 Ac ys c9 cm como como Bank01 Boo c 9 e c m mh Port 6 P PortlD 0106 7 geo EE nri P PortiD o70g Port PortlD 0702 Note The above working diagram represents an JKP1610LS 16 ports KVM Switch cascade with the JKP115 801e 117 801e KVM Switch For example To access a PC with the port ID 0008 Press SCROLL LOCK SCROLL LOCK 0008 To access a PC with the port ID 0702 Press SCROLL LOCK SCROLL LOCK 0702 18 Reset PC Name This function resets PC Name settings to default values Quick View Scan Mode The Quick View Scan feature allows you to monitor the activity of the connected computers at regular intervals so that you can monitor the computer activity without having to take the trouble of switching yourself This time interval can be changed as desired Note 1 The interval between these two keys should be no more than 0 5 seconds Once the scanning begins it continues until you press any key to exit Quick View Scan Mode 2 A Port LED will flash indicating that the connected computer is under Auto Scan mode Setting the Quick View Scan Time The scan time or the time the Switch spends on each
10. ASTER ENTER SELECT 1 UP DOWN INS RENAME SPACE SPACE ADMIN ESC EXIT Note When Hot plugging computer ports you must manually refresh exit and re enter the OSD menu to display the new status information of the corresponding port The OSD Overview Menu displays a list of connected computers controls and function keys as well as symbols that refer to the status of each computer 21 Navigation Use the following to navigate through the OSD menu To escape from the OSD menu or sub menu press the Esc key To move up and down through the screen list use the Up Down arrows Move the highlight bar to the desired location and press Enter to activate a port OSD Heading Description Port or server name that is designated by the user See OSD Functions in the next section under Port Naming The symbol indicates that the computer connected to that port is powered on If a computer is connected and powered on but the OSD menu does not display a 3t symbol reset the Switch in order to re detect the server To reset the Switch press the Port 1 and Port 2 manual push button selectors simultaneously for 2 seconds An E Symbol displays when cascading computers Lists the port identification numbers for all connected servers The 2 digits read left to right consist of the BANK and PORT number respectively To gain access to a computer move the highlight bar over a server in the name list and hit Ente
11. M Cable set includes an industry standard coaxial VGA cable and nickel plated connectors for high resolution applications The following cables are recommended for your JKP1 KVM installation Single Installation Multiple Installations Cascaded e K15C6P L 1 8M e K15C9P L 3 0M e 15 L 4 8M Power Supply An 100 240 50 60Hz is recommended Operating Systems Windows 98 Me NT 2000 XP 2003 server FreeBSD LinuxR NovellR NetWare 4 x 5 x Computers Keyboards 6 Pin PS 2 mini DIN Mice 6 Pin PS 2 mini DIN Monitors VGA SVGA MultiSyncR SPECIFICATIONS JKP115 801e JKP115 1601e JKP117 801e JKP117 1601e wem m mens m o T inpuS gral Keyboardand Key Pad PS keytoardw huuh pad Power Sump 102 240 30 GER Sum Omar Boream OSDBP OSDV P 050 Tre LCD On SarenD Largiage Recall Pot Se keen OSD Boc Key Bush Campurr Corrrcm 900215 Fernak Mouse Vh Commer Conect Commer Correct 56 ener 5 Ternperanet D 40 deg C noperacrg 20 60 deg C Burney D 30985 RB ren condec rg Hore See amp 44 x 56052 244 25 1E Ll 4431 390 32 4425 Fash Upgrade Fernsate dede Note Specifications are subject to change wi
12. and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Shielded interface cables must be used in order to comply with emission limits You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation CE Mark Warning This is a Class B product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures VCCI Warning 36
13. e of your JKP1 KVM switch CHANGGE PASSWORD Modify and or delete user passwords Resets OSD function setting to default values server names designated by the administrator are NOT affected Perform an OSD Reset when Daisy Chaining or RESET when keyboard mouse inactivity is experienced NOTE Pressing SCROLL LOCK SCROLL LOCK Delete will reset the OSD to its factory default settings FIRMWARE UPDATES Firmware upgrades enable your KVM switch to maintain consistent compatibility with the latest devices and computers Firmware upgrades are free for the life of your JKP1 KVM switch Refer to the Windows flash upgrade instructions below for the latest upgrade software information and support To update the firmware you will need the following items 1 A separate computer running Windows 95 98 ME 2000 or XP This computer must not be connected to the CPU ports on your KVM switch 26 2 An available serial port on the computer 3 Acustom serial cable 8 pin to RS232 9 pin included in package 4 Firmware update files available at customer support web site Set Up To setup for the flash upgrade do the following 1 2 Open the firmware upgrade program by double clicking on the latest firmware file from customer support web site Use a computer that is not connected to your KVM computer ports Connect the power cord to the power jack of the KVM switch Then plug the power cord into an ava
14. ilable power outlet Using a serial cable 8 pin to RS232 9 pin connect an available COM port on your computer Take the other cable end and connect it to the FLASH port on the rear of the KVM switch Succentul 1 Shuatova yow aad AU cables that conzecw your The will yos to imet 2 You Be se Demi EYN 27 LCD CONTROL CONSOLE JKP115e 117e OVERVIEW The JKP115e 117e is a rackmounted control console designed for 19 rack systems The JKP115e 117e is designed for the control and access of server farms or automation applications The JKP115e 117e integrates a 15 17 inch color TFT LCD module which supports up to XGA 1024 x 768 and 16 7M 8 bit color The new innovative design with heavy duty steel housing and aluminum front brezel meets tough environmental standards Whether it s in educational government or corporate sectors the JKP115e 117e provides network administrators and IT managers a stable management tool for server access and control FEATURES Stable management tool 1U 19 design for universal setting 15 17 color TFT LCD module 3 Step rack mount installation Easy maintenance PACKAGE CONTENTS The complete JKP115eRM 117e package consists of Item Qty Remark JKP115eRM 117e 1 19 Rackmount LCD KVM console drawer Power Cord 1 Power Adapter 1 Bracket 2 User Manual 1 KVM Cable 1 28 Check to make sure that the unit was n
15. in 19 inch rack systems The sliding brackets feature adjustable positions for rack depths of 22 36 inches Important Information Installing and or removing the Switch module and chassis improperly could void your warranty If you are uncertain what to do please contact our technical support Please follow these simple steps to install the JKP1 into a server rack 1 Adjust the sliding rack mount brackets to match the depth of your server cabinet Fix both brackets at a desired height to the server cabinet rails Note The slider brackets are extendable to a rack depth of 22 to 36 3 Fasten the front end bracket screws Your JKP1 Switch is now ready for use locate the handle slide out the console and flip the LCD cover Note The front end bracket screws must be fastened to properly secure the JKP1 chassis to the server rack LCD FLAT PANEL DIPSLAY Panel Controls and OSD Functions POWER Press MENU Button display will show following picture Continue to press and e button to select function Then press SEL to enter these functions and adjust them to your personal Auto Auto Brightness Contrast Horizontal Vertical Color OSDHP OSDVP OSD Time Language Recall Exit Power On Off switch Soft power on off button Adjacent LED is lit when on Auto Auto synchronize and scale down display to any valid factory preset timings l9 Press to scroll the function you want to adjus
16. key sequence from your keyboard Manual Port Selectors Push button selectors allow for convenient manual PC selection LCD Bank Display The LCD Bank Display shows bank identification when cascading Quick View Scan The Quick View Scan function allows you to automatically scan and monitor all computers one by one that are connected to your JKP1 KVM switch Video Resolution The 15 17 LCD monitor supports 1024 x 768 1280 x 1024 75Hz Port LED Display Port LEDs allow for easy status monitoring of all connected computers A lit Green LED indicates which computer the KVM console currently has control of A Red LED indicates which computer is connected but not in use Sliding 1U console Drawer The entire LCD KVM console simply slides away into a compact 1U rack space when not in use 2 FEATURES Control 8 and up to 16 computers directly from a single PS 2 console Multi Bank installation Cascaded control up to 128 256 computers respectively Allows users to control up to 8 115 801 117 801 and up to 16 JKP115 1601e JKP117 1601e computers directly from an integrated 1U console drawer Control up to 128 256 computers respectively via a Cascade installation Convenient computer selection via intelligent On Screen Display OSD Menus Hot Keys or Manual PC Selectors Auto Sensing of Bank Position on Cascade installations 7 segment LED display for BANK identification when Cascading Quick View Sca
17. n for monitoring connected computers Console s mouse port or touch pad can be easily used to control connected computers Password Security lock access to connected servers No software required for installation Hot Pluggable add remove computers without powering down the Switch Keyboard and mouse emulation intelligently manages booting via independent channel microprocessors Optional 15 17 RGB LCD monitor supporting 1024 x 768 1280 x 1024 75Hz 1U rack mountable at any user height in a 19 system rack console drawer simply slides away when not in use New Rackmount Advantages One person installation saves valuable human resources and time Quick release rack mount draw thumbscrews Adjustable rack slides for convenient positioning in 22 36 server racks PACKAGE CONTENTS Item Qty Remark JKP115 801e 117 801 1 19 Rackmount LCD KVM drawer JKP115 1601e 117 1601e Power adapter 1 Bracket 2 User Manual 1 Flash Cable 1 Power Cord 1 Please check to make sure that each item of the above list is included in your JKP1 package Contact your dealer immediately if any item is missing or damaged in shipment EQUIPMENT REQUIREMENTS Cables It is highly recommended that you use only our KVM Cable sets These cables offer the highest quality possible to ensure optimal data transmission our KVM cables feature micro cable construction and are molded together for a neat and organized setup All in one KV
18. onnecting your External Mouse To select a mouse option do the following Switch to External Mouse port use 1 Select the External mouse from the switch located on the front panel of the JKP1 KVM switch 2 Connect your external mouse to the mouse port located on the front panel of the JKP1 KVM switch Switch back to Touchpad Mouse use Select the Touchpad mouse from the switch located on the front panel of the JKP1 KVM switch MULTIPLE STAGE INSTALLATION Cascading This section provides complete instructions for the hardware setup of installing cascaded computers To control even more computers up to 8 JKP115 801e 117 801e and 16 JKP115 1601e 117 1601e additional switches can be cascade from the CPU ports of the First Stage Master switch The cascaded Switches that connect back to the First Stage switch are referred to as Second Stage switches or BANKS and assigned a location For example the Console keyboard monitor and mouse connects to BANK 00 or the Master switch As many as 128 256 computers can be controlled by a system administrator in a complete multi bank installation To set up a Multiple Stage Installation do the following 1 Power off all computers 2 Using the all in one KVM Cable set Part No K15C6P Take the male HDDB 15pin connector and plug it into the PC1 port indicated on the rear of the KVM Switch Connect the other male VGA HDDB 15 cable end to the console VGA port of the second stage switch
19. ot damaged during shipment If you encounter a problem contact your dealer Please read this manual thoroughly Follow the installation guide and operation procedures carefully to prevent any damage to the JKP115eRM 117e and or any of the devices that connect to it SPECIFICATIONS Lone 5 2 5 2 15 D Sub NNNM Connections t a Auto Brightness Contrast Horizontal Vertical Color OSDHP OSDVP oe OSD Time Lanquage Recall Exit 0 40 deg C In operating 20 60 deg C In storage 448 20 x 560 52 x 44 25 10 3kg 448 20 x 560 52 x 44 25 mm 10 7kg Note Specifications are subject to change without notice 29 DISPLAY DIAGRAMS Front View Console Drawer Handle LCD Display 15 17 LCD Display Controls External mouse port Touchpad and keyboard Mouse and touch Pad switch Power LED Power Switch o o noo o wm Rack mounting Brackets Rear View 1 DC input 2 CPU Port Connect your computer KVM switch here 30 HARDWARE REQUIREMENT Computer 6 Pin PS 2 mini DIN keyboard port 6 Pin PS 2 mini DIN mouse port VGA SVGA MultiSyncR Above equipment must be built in one computer KVM The KVM console must support the following specification 6 Pin PS 2 mini DIN keyboard port 6 Pin PS 2 mini DIN mouse port VGA SVGA MultiSyncR Installing the Switch into a Server Rack Unlike other traditional rack m
20. ounted LCD KVM units the RM series requires only one person for installation The RM series includes 2 adjustable sliding rack mount brackets for installation in 19 inch rack systems The sliding brackets feature adjustable positions for rack depths of 22 36 inches Important Information AN Installing and or removing the Switch module and chassis improperly could void your warranty If you are uncertain what to do please contact Technical support Please follow these simple steps to install the RM into a server rack 1 Adjust the sliding rack mount brackets to match the depth of you re your server cabinet Fix both brackets at a desired height to the server cabinet rails Note The slider brackets are extendable to a rack depth of 22 to 36 gt 2 31 2 Gently slide the RM chassis into the fixed brackets of the rack rail assembly 3 Fasten the front end screws Your RM Switch is now ready for use locate the Smart handle slide out the console and flip the LCD cover Note The front end screws must be fastened to properly secure the RM chassis to the server rack Installation of JKP115eRM 117e 1 Plug the VGA Mouse Keyboard cable to the JKP115eRM 117e unit The other end plugs into the computer or KVM s console 2 Plug the power cord into JKP115eRM 117e s power jack then plug the power cord into an AC power source 3 Turn the JKP115eRM 117e on by pushing the Power on button 5 gt Pu om
21. port can be changed using either Hot Keys or OSD Password Security Locking Server Access Administrators can set a unique password to restrict access to computers connected to the JKP1 switch Changing your Password To set a new password do the following 1 Invoke the Hot Key mode by pressing the SCROLL LOCK key twice within two seconds 2 Key in R 3 Enter old password up to 15 characters 4 Enter the new password up to 15 characters 5 Re enter the new password for confirmation Hotkey Beeper Confirmation The beeper function can be turned on and off as desired using the following Hotkey sequence 18 HOT KEY COMMANDS SUMMARY On Screen Port Identification tag Previous active channel E Next active channel Switch to Port X X 01 16 Switch to Port X on Bank Y Y 00 16 cascading B Previous active bank B Next active bank SSE E 0 Sa un Switch to Master switch Enable OSD Mode B Set OSD display time 7 sec B Set OSD display time 15 sec Set OSD display time 30 sec Set OSD display time 60 sec Reset OSD menu Reset PC Name B Quick View Scan mode B Stop Quick View Scan mode Turn On Off Beep confirmation 1 beep ON 2 beeps OFF Set Quick View Scan time 7 sec B Set Quick View Scan time 15 sec B Set Quick View Scan time 30 sec B Set Quick View Scan time 60 sec B Set Alternative Shift Hot Key B Set Default Scroll Lock
22. r To gain BANK level access when cascading computers move the highlight bar over a server in the name list and press SCROLL LOCK twice to display the BANK OSD For example a cascaded KVM switch connected to the Master switch Port 2 will show the preceding BANK numeral as 2 OSD Main Menu Functions This section provides details on the use of the following OSD functions HOME MASTER UP DOWN SPACE ADMIN ENTER INS and ESC From the main OSD mode the following OSD functions can be accessed HOME MASTER To return the KVM focus to the Master switch s first active port press Home from the keyboard UP DOWN To select any computer at the same KVM stage move the highlight bar using the Up Down arrow keys and press Enter e g Bank 01 Ports 01 to 16 Bank 00 Ports 01 to 16 22 Accessing computers using the OSD To access computers of the Master Switch 1 Invoke the Hot key mode by pressing the SCROLL LOCK key twice within two seconds 2 SPACE 3 Move the highlight bar between 1 and 8 4 Press ENTER to gain access to the computer shown with a symbol Note the OSD display will be dismissed after ENTER is pressed NAME PWR Port 1 COMPUTER 1 0 1 2 COMPUTER2 0 2 3 COMPUTER3 0 3 4 COMPUTER 4 0 4 5 COMPUTERS5 X 0 5 6 COMPUTERS 0 6 7 7 0 7 8 COMPUTER 8 0 8 HOME MASTER ENTER SELECT 1 UP DOWN INS RENAME SPACE SPACE ADMIN ESC EXIT
23. r switching back to the Master switch port 1 of the Master switch is always the first to be shown SPACE SPACE ADMIN To access the Administration sub menu press SPACE SPACE from the main OSD menu see next section for details 24 ENTER To confirm a selection and save the content input press ENTER NAME PWR Port 1 COMPUTER E 0 1 2 COMPUTER2 0 2 COMPUTER3 0 3 ESC To exit the current OSD menu press ESC OSD Administration Sub Menu This section provides details on configuring default Hot keys to setting up user password access To access the Administration sub menu complete the following 1 Press SPACE SPACE from the main OSD menu see above The OSD overlay screen appears ADMINISTRATION CHANGE HOT KEYS CHANGE SCAN TIME CHANGE DISPLAY TIME FIRMWARE INFORMATION CHANGE PASSWORD RESET T MOVE UP ENTER SELECT 4 MOVE DOWN ESC EXIT 25 OSD Function Description CHANGE HOT KEYS Changes the default HOT Key option Scroll Lock Shift CHANGE SCAN TIME Quick View Scan allows users of large installations hands free automatic scanning and viewing of all connected ports for a selected time interval You may choose 7 15 30 or 60 seconds CHANGE DISPLAY TIME Changes the amount of time the OSD menu is displayed on screen and also specifies the amount after making a port selection You may choose 7 15 30 or 60 seconds FIRMWARE INFORMATION Indicates version and mak
24. s setting Color ICON Description 9300 To set CIE coordinate at 9300 color 6500 To set CIE coordinate at 6500 color RIGIB 0 255 R G B 0 255 OSDHP Adjust OSD horizontal level 0 255 OSDVP Adjust OSD vertical level 0 255 OSD TIME Adjust OSD time 5 60 seconds Language Chinese English Recall Adjust LCD setting back to previous setting Power Indicator GREEN ON ORANGE STANDBY ORANGE SUSPEND 18 SINGLE SWITCH INSTALLATION This section provides complete instructions for the hardware setup of a single JKP1 KVM switch in which there are no other KVM switches cascaded Connecting the Computers 1 Power off all computers 2 Using all in one KVM Cable set Part No K15C6P take the male HDDB 15pin connector and plug it into the PC1 port indicated on the rear of the KVM Switch Connect the other male VGA HDDB 15 cable end to the VGA port of the computer you re installing 3 Connect the PS 2 keyboard and mouse connectors of the KVM cable set to the corresponding keyboard and mouse ports on the computer hm dom dim de dm amp l 4 Repeat step 1 and 2 for each additional computer you wish to connect Connecting the Power Supply 1 Connect the power cord to the power jack on the rear of the Switch Then plug the power cord into an available power outlet 2 Power on the Switch s LCD display 3 Power on your computers aj 13 C
25. set confirmation Confirmation Procedure Once all computers are powered on the switch emulates both mouse and keyboard signals on each port allowing your computer to boot normally without errors To make sure your Cascade installation was successful do the following 1 Press SCROLL LOCK twice and enter your 4 digit port ID code For example if Cascading is successful press SCROLL LOCK SCROLL LOCK 07107 then the monitor will show PC s screen Check to see that the keyboard monitor and mouse are working normally Proceed to do this with all occupied ports to verify that all computers are connected and responding correctly If you encounter an error check your cable connections for that computer and reboot 18 OPERATION Controlling your computers with the JKP1 series couldn t be easier The JKP1 series allows you to access the computers using three simple methods Hot Keys Manual Selectors OSD Screen Display Menu PC Manual Selectors You can select any computer or access any Bank by using the PC selectors located at the top left of the console draw Manual Selectors You can directly select any single computer or access any connected Bank by using direct access PC selectors located at the top left of the KVM console Each port switch has a corresponding LED for easy status monitoring A Green LED indicates current port selection Selected A Red LED light indicates a port is not selec
26. t Press to scroll the function you want to adjust Menu To access the main menu This button also acts as the Enter button Auto tracking positioning phase and size 1 Press the Menu button 2 Usethe and e button to scroll 10 Brightness Contrast Horizontal Vertical Color OSDHP OSDVP OSD Time Language Recall Exit 3 Press the SEL button to enter 4 Use the button to adjust the brightness of the display 5 Press the SEL button to go back to main menu Brightness Adjust LCD brightness level 0 255 of the image 1 Press the Menu button Use the and 4 button to scroll 2 Auto Contrast Horizontal Vertical Color OSDHP OSDVP OSD Time Language Recall Exit 3 Press the SEL button to enter 4 Use the LOR and button to adjust the brightness of the display 5 Press the SEL button to go back to main menu Contrast Adjust white color level 0 255 of the image 1 2 Press the Menu button Use the e and button to scroll Auto Brightness Horizontal Vertical Color OSDHP OSDVP OSD Time Language Recall Exit Press the SEL button to enter Use the and 4 button to adjust the brightness of the display Press the SEL button to go back to main menu 11 Horizontal Adjust LCD display horizontal level 0 255 Vertical Adjust LCD display vertical level 0 255 Recall Adjust LCD setting back to previou
27. ted but the connected computer is powered and ready Online The JKP1 series is also equipped with seven segment LCD display for BANK identification when cascading HOT KEYS Port Identification Each computer in a JKP1 installation has a specific port ID You can directly switch the KVM focus to any computer by entering the switch port number and the BANK number for cascaded installations Each is assigned a two digit numeric ID Single Switch Installation The Port number X is a two digit number that identifies the port on the 1 switch that the computer is connected to For example a computer connected to Port 8 has the numeric ID of 08 Multiple Switch Installation Cascading The Port number X is a two digit number that identifies the port on switch that the computer is connected to The BANK number Y is a two digit number that identifies the Switch s position in the cascade installation Note the BANK number always precedes the Port number For example a computer connected to Port 8 of BANK 6 has the numeric ID of 0608 Selecting the Active Port Directly switch the KVM focus to any computer by entering the Port number and or the BANK number Single Stage Installation Port number 8 7 6 5 4 3 2 1 4 PortlD 08 PortlD 05 PortlD 01 For example To access a PC with the port ID 08 Press SCROLL LOCK SCROLL LOCK 08 To access a PC with
28. thout notice DISPLAY DIAGRAMS Front View Console Drawer Handle LCD Display 15 17 LCD Display Control see the LCD Display Guide for details Power Switch LCD Bank Display External Mouse Port Touchpad Mouse amp Touch Pad Switch o oN A QN Rack Mounting Brackets A Manual Port selectors 1 8 1 16 Rear View 1 DC Input 2 Firmware Upgrade Port 3 PC Ports INSTALLATION Where to Place the Switch The enclosure of the JKP1 Switch is designed for standalone or rack mount configuration The Switch is natively rack mountable in a standard 1U 19 server rack Rack mount hardware is included with your Switch for a sturdy rack installation Cautions and Warnings Avoid placing cables near machines that create electrical noise such as fluorescent lighting air conditioning equipment etc Important Information Before you begin make sure that power to all the computers you will be connecting has been powered off To prevent damage to your installation due to ground potential difference make sure that all computers on the installation are properly grounded Failure to follow these instructions can result in damage to computers and or the Switch Installing the Switch into a Server Rack Unlike other traditional rack mounted LCD KVM units the JKP1 series requires only one person for installation The JKP1 series includes 2 adjustable sliding rack mount brackets for installation

User Manual - I

Contents

Download Pdf Manuals

Related Search

Related Contents