KIC550 - Fastwel
Contents
1. Carefully insert the module into the required slot moving it along the guide rails until it touches the mezzanine board connector Using the handle of the front panel insert the module into the mezzanine board connector The device is properly installed when the ejector handle makes a clear click sound Fix the module by two holding screws on the front panel of KIC550 see Figure 1 2 Connect all the required external interface cables to the module Make sure that both KIC550 and all the cables connected to it are properly fixed KIC550 is ready for operation KIC550 User Manual 2013 Fastwel Ver 0 03 46 KIC550 Storage Module Fastwel Lee Specification 4 3 Module de installation procedure To de install the module you need to perform the following operations 1 6 If the Hot Swap of the module is carried out comply the sequence of operations described in subparagraph 2 3 2 and follow the indication on the front panel 1 Make sure that the safety requirements of subparagraph 4 1 are met Attention Subsequent operations should be carried out with care avoiding damages to both KIC550 and other system devices 2 Before de installing the KIC550 make sure that the system power supply is switched off 3 Disconnect all interface cables from the module 4 Remove the holding screws from the front panel 5 Unblock the ejector handle on the front panel by pressing a white button and lowering the handle do2. Turn off system supply and replace the damaged storage device with the identical one that operates properly The 88SE9130B controller will define the new storage device as Free Physical Disks in the Topology menu KIC550 User Manual 2013 Fastwel Ver 0 03 39 KIC550 Storage Module Topolog Free Physical Disks Help i Fastwel Le Specification Marvell BIOS Setup c 2009 Marvell Technology Group Ltd Information Port ID PD ID Type Status Size Feature Support Current Speed Model Serial FW Version Physical Disk can be combined into a YD ENTER Operation F10 Exit Save ESC Return o 0 SATA PD Unconfigured 95386948 NCO 66 48Bits 6G WOC WD1002FAEX 0073A0 WO ABCDE1 234567 05 12321 KIC550 User Manual 2013 Fastwel Ver 0 03 40 KIC550 Storage Module Fastwel Lee Specification In the Topology menu select the Virtual Disks Test and press Enter In the dropdown menu select Rebuild option and press Enter Marvell BIOS Setup c 2009 Marvell Technology Group Ltd Topolog Information HBA 0 Marvell 0 ID Virtual Disks Name Ces 0 We Status Stripe Size Free Physical Rebuild RAID Mode LWDD 1 WDC A Size BGA Status Number of PDs Members Help Virtual Disk A set of disk blocks presented to an operating environment as a range of consecutively numbered logical blocks with disk like storage ENTER Operation F10 Exit Save ESC Return Open the Free Ph
3. srace Select F10 Exit Save ESC Return KIC550 User Manual o2013 Fastwel Ver 0 03 27 KIC550 Storage Module Fastwel Lee Specification Note The 88SE9130B controller always requires two physical discs to create the virtual disc After selection of the discs press Enter The information window of the Create Virtual Disk menu will show various possible virtual disc configuration options The lower Help window will list the available menu navigation and control options Marvell BIOS Setup c 2009 Marvell Technology Group Ltd Configure gt Select free disksCreate Virtual Disk i Ee E Virtual Disks Free Physical Disks Stripe Size t 64KB i HDD O WOC WD1002FAEX HDD 1 WDC WD1002FAEX Nane t Default Next Help Virtual disk configurations ENTER Select rio Exit Save ESC Return Note Depending on the software version some of the menu options could be unavailable In the right menu window select HyperDuo and press Enter A dropdown menu containing a list of available virtual disc options will appear Select RAID 0 or RAID 1 option depending on the desired RAID type see paragraph RAID functions and press Enter KIC550 User Manual 2013 Fastwel Ver 0 03 28 KIC550 Storage Module Fastwel Lee Specification 1 RIOS Setun fe NNG Sivoo gt etup c c lt uus ct free disksCreate Virtual Dis U1SKS Le O WDC WDIOO2FAEX Keep original data Yes HDD 1 WDC WDIOO2FAE
4. Fastwel Co Ltd reserves the right to change modify and improve this document or the products described in it at Fastwel s discretion without further notice Software described in this document is provided on an as is basis without warranty Fastwel assumes no liability for conseguential or incidental damages originated by the use of this software This document contains information which is property of Fastwel Co Ltd It is not allowed to reproduce it or transmit by any means to translate the document or to convert it to any electronic form in full or in parts without antecedent written approval of Fastwel Co Ltd or one of its officially authorized agents Fastwel and Fastwel logo are trademarks owned by Fastwel Co Ltd Moscow Russian Federation Ethernet is a registered trademark of Xerox Corporation IEEE is a registered trademark of the Institute of Electrical and Electronics Engineers Inc Intel is a trademark of Intel Corporation Pentium M and Celeron M are trademarks of Intel Corporation Microsoft is a trademark of the Microsoft corporation In addition this document may include names company logos and trademarks which are registered trademarks and therefore are property of their respective owners Fastwel welcomes suggestions remarks and proposals regarding the form and the content of this Manual KIC550 User Manual 2013 Fastwel Ver 0 03 6 KIC550 Storage Module Fastwel Lee Specification Trademarks Fastwel l
5. Marvell Technology Group Ltd onfigure gt Select free disks l Marv Port ID MI Virtual Disks PD ID t Free Physical Disks Type SATA PD d O WOC WO1002FAEX status Unconfigured Size 953869MB Feature Support WCQ 6G 48Bits Current Speed 6G Model WOC WD1002FAEX 00Z3A0 Sertal WD ABCDE1234567 FW Version 08 12321 Help Use space bar to select the free disks to be used in the array ENTER Operation srace Select F10 Exit Save ESC Return KIC550 User Manual 2013 Fastwel Ver 0 03 32 KIC550 Storage Module Fastwel Lee Specification Note The 88SE9130B controller always requires two physical discs to create the virtual disc After selection of the storage devices please press Enter The information window of the Create Virtual Disk menu will show various possible virtual disc configuration options The lower Help window lists the available menu navigation and control options KIC550 User Manual 2013 Fastwel Ver 0 03 33 KIC550 Storage Module Fastwel Lee Specification Thane gt Free 1 Disks Stripe Size HDD O WDC MD1002FAEX a a a du HDD 1 WDC MD1002FAEX Name Default Next Help Virtual disk configurations S i ENTER Select F10 Exit Save ESC Return Note Depending on the software version some of the menu options could be unavailable In the right menu window select HyperDuo and press Enter A dropdown menu containing a list of available virtual disc
6. Virtual Disks PD ID L Type T H U UU LU nu Free Physical Disks Current Speed Model WDC WD1002FAEX 00Z3A0 Serial WD ABCDE1234567 FW Version 05 12321 Help Erase RAID configuration data from the selected physical disk ENTER Operation F10 Exit Save ESC Return 3 5 4 Virtual disc rebuilding RAID 1 virtual disc generated by the 88SE9130B controller can be rebuilt if either of the storage devices fails Note Notwithstanding the fact that BIOS Setup program of the 88SE9130B controller supports manual disc rebuilding mode Marvell Storage Utility MSU which functions in the operating system environment cannot be used for initiating resuming or completing of the rebuilding process Redundancy of physical discs is not supported KIC550 User Manual 2013 Fastwel Ver 0 03 38 KIC550 Storage Module Fastwel LE Specification 3 5 4 1 Manual virtual disc rebuilding In case of virtual disc failure its Status is changed from Functional to Degrade Marvell BIOS Setup c 2009 Marvell Technology Group Ltd Topology HBA O Marvell O Ke Disks LWOD 1 WOC ND1002FAEX Free Physical Disks Information ID Name Status Stripe Size RAID Mode Size BGA Status 2 Number of PDs Members Help Virtual Disk A set of disk blocks presented to an operating environment as a range of consecutively numbered logical blocks with disk like storage ENTER Operation F10 Exit Save ESC Return
7. appeared system message window confirm the virtual disc creation by pressing Y The created virtual disc should appear in the list of Topology window KIC550 User Manual 2013 Fastwel Ver 0 03 36 KIC550 Storage Module Fastwel Lee Specification Marvell BIOS Setup c 2009 Marvell Technology Group Ltd onfigure gt Select free disksCreate Virtual Disk HyperDuo Safe Yirtual Disks Free Physical Disks Lea 0 C300 MTFDDAC25 Keep original data Yes HDD 1 WDC WD1002FAEX N efaul Threshold x 90 Help Virtual disk configurations ENTER Select F10 Exit Save ESC Return 3 5 3 Deleting RAID configuration parameters The physical discs that were previously used in the virtual RAID disc or array often save RAID configuration data obtained from that disc or array In order to use these physical discs with the new virtual disc the previous RAID configuration needs to be erased Attention If the physical disc initially was a part of the other virtual disc deleting RAID configuration data could damage such virtual disc In the Topology window select Physical Disk Test gt HDD 0 Disc type and press Enter In the dropdown menu select Erase RAID Config Data and press Y key to confirm the operation KIC550 User Manual 2013 Fastwel Ver 0 03 37 KIC550 Storage Module Fastwel Lee Specification Marvell BIOS Setup c 2009 Marvell Technology Group Ltd Topology Information HBA 0 Marvell O Port ID
8. is simultaneously supported by the processor module KIC550 User Manual 2013 Fastwel Ver 0 03 15 KIC550 Storage Module Fastwel Lee Specification 1 5 2 Main components layout Fig 1 2 Layout of KIC550 main components top view Dimensions o gl Sf Ge O o HLI XSI i eee REN mun IP HIE SW1 Operation mode switch XS2 CFast connector ET 9 ER J 7 XP2 a B C g mg XS3 2 5 storage carrier connector U o A A gh KIC550 421459 550 CG XP4 Bottom fixing screw CFast removable cover Ejector button Upper fixing screw Appearance of the module hardware versions can have insignificant variations from the one shown on the Figure This Figure shows the upper side of the KIC550 module and the front panel view KIC550 User Manual 2013 Fastwel Ver 0 03 KIC550 Storage Module Fastwel Lee Specification Fig 1 3 Reverse side of KIC550 Appearance of the module hardware versions can have insignificant variations from the one shown on the Figure This Figure shows the reverse side of the KIC550 module The board is implemented in the 3U CPCI Serial form factor with due consideration of all the requirements provided for by the PICMG standard CFast storage device is removed from a hole of the module s front panel The SATA storage device should be fixed on the board by screws KIC550 User Manual 2013 Fas
9. options will appear Select the desired HyperDuo mode option Safe or Capacity see paragraph Marvell HyperDuo functions and press Enter KIC550 User Manual 2013 Fastwel Ver 0 03 34 KIC550 Storage Module Fastwel Lee Specification Marvell BIOS Setup c 2009 Marvell Technology Group Ltd Configure gt Select free disksCreate Virtual Disk Virtual Disks Free Physical Disks Keren SSD 0 C300 MTFDDAC26 Keep original data Yes city HDD 1 WDC WD1002FAEX RAID 0 Threshold x 90 RAID 1 Next Help Virtual disk configurations ENTER Select OU Exit Save ESC Return If the Safe option is selected it is possible to save the original data on the storage device while creating the virtual disc To confirm data saving select Yes in the dropdown menu Select No if you don t need the data to be saved Marvell BIOS Setup c 2009 Marvell Technology Group Ltd Configure gt Select free disksCreate Virtual Disk HyperDuo erte o Next Wirtual Disks Free Physical Disks SSD 0 C300 MTFDDAC 25 HDD 1 WDC WD1002FAEX Help Virtual disk configurations ENTER Select OLJ Exit Save ESC Return KIC550 User Manual 2013 Fastwel Ver 0 03 KIC550 Storage Module Fastwel Lee Specification Note Where the virtual disc is created with the Capacity option all the data on the storage devices will be deleted Upon completion of the virtual disc configuration select Next and press Enter In the
10. power supply voltage range YY RAY HL ALL LLA LL LLALL LLA EL ER ELLA DL LY LYN Doa 49 Table 5 2 KIC550 current Consumption YY LLY ALL LLALL RALL LLALL tt trt LLALL ER ELLEN LEL DR ED RL DY En on 49 Table 5 3 Parameters of climatic and mechanical effects CPChOp LLE eee teeta Y YY YY Y LEon 50 KIC550 User Manual 2013 Fastwel Ver 0 03 KIC550 Storage Module Fastwel Lee Specification List of Figures Fig 1 1 Appearance of KIC550 with the installed storage device and memory Card 15 Fig 1 2 Layout of KIC550 main components top view Dimenslons eee YY LYW FFY tees 16 Fig 1 3 Reverse side of KIChbO 0 nea ELN FEN teenie 17 Fig 2 1 Block diagram of KICRbO oc ne eet a eneeeeeeeeeeeee 18 Fig 3 1 Position of the SW1 1 mode selector switch of KIC550 0 ecee cece eeceee eee ete FFY eee FFI nL ion 22 Fig 3 2 RAID consisted of two discs NO redundancy cece eee ee eee ER Y teeta eee n teen ete ea en een tanta ee nno 24 Fig 3 3 RAID En e EE 24 All information in this document is provided for reference only with no warranty of its suitability for any specific purpose This information has been thoroughly checked and is believed to be entirely reliable and consistent with the product that it describes However Fastwel accepts no responsibility for inaccuracies omissions or their conseguences as well as liability arising from the use or application of any product or example described in this document
11. 03 26 KIC550 Storage Module Fastwel Lee Specification 3 5 Creation of virtual discs 3 5 1 Creation of virtual RAID The virtual RAID can be created by means of the Configuration Wizard in the Topology window select HBA 0 Marvell 0 and press Enter a window invitation to the Configuration Wizard mode will appear as a result Marvell BIOS Setup c 2009 Marvell Technology Group Ltd Topology Information 1B4B Virtual Disks 9130 Free Physical B1 HDD O WDC WD1OO2FAEX BIOS Version 1 0 0 1029 HDD 1 WDC WDIOD2FAEX Firmware Version 2 2 0 1118 PCle Speed Rate 0 Configure SATA as AHCI Mode Supported Mode RAIDO RAIDI Safe Capacity Help Marvell RAID on chip controller ENTER Operation F10 Exit Save ESC Return Use the arrow keys to select available hard discs for creating the virtual disc Selection or de selection of the discs is made by the Space key CH When the storage device is selected symbol appears to the left of it Marvell BIOS Setup c 2009 Marvell Technology Group Ltd onfigure gt Select free disks i HBA Marve Port ID SS Virtual Disks PD ID hee Free Physical Disks Type SATA PD E HDD O WDC WD1OD2FAEX Status Unconfigured Size 953869MB Feature Support WCQ 66 48Bits Current Speed 66 Model WOC WD1002FAEX 0073A0 Sertal WD ABCDE1234567 FW Version 08 12321 Help Use space bar to select the free disks to be used in the array ENTER Operation
12. 50 two storage devices 2 5 CFast enable the creation of RAIDs of the following levels RAID O Striping is the increased capacity array provides no fault tolerance RAID 1 Mirroring is the mirroring redundant array of independent discs RAID 0 is an array consisting of two discs no data redundancy The information is split into the fixed length data blocks and is at the same time recorded to the both discs which significantly improves the performance In this case the reliability is sufficiently lower than the reliability of any disc taken apart since the failure of any of the discs leads to inoperability of the whole RAID KIC550 User Manual 2013 Fastwel Ver 0 03 23 KIC550 Storage Module Fastwel Specification Fig 3 2 RAID consisted of two discs no redundancy Physical Disks Virtual Disk Legend Empty area of disk ee Disk filled with fragment A RAID 1 is an array of two hard discs being exact copies of each other Application of such an array ensures an appropriate write transaction rate and offers an advantage in terms of the read transaction rate while multiple I O requests are to be serviced in parallel The array delivers high reliability it continues to operate as long as at least one drive is functioning Fig 3 3 RAID 1 Mirroring Virtual Disk Physical Disks Legend Empty area of disk e Disk filled with fragment A EE A Mirror of fragment A KIC550 User Manual 2013 Fastw
13. F FFR FFR YF EG NE FN RHEN 7 ege 7 NEE ee Eege 8 E E 9 General Board Operation Elte esskueeskstgresn CO GYLL C ARR UGADNGDUUGAxURERUE EEN 10 TRANSPORTATION UNPACKING AND STORAGE 0 cs eeeceeeeeeeeeeeeeeeeeeseeeeeeeeseeeeeeeseeaes 11 tae og Lo a FEED HNN OFHI FU AF EF FEHEFIN 11 A gi oz 1o 51g FEED cc n POEN HF EF A FR REF 2 AN FN FFF FN FR 11 SE 11 MANUFACTURER S GUARANTEES u X lt cuuwiuu nu LiNYLG uu GN NL CLLR EN NLd CRAD Hn DNA AABAD ENA EE ADDAW ADEN Nun 12 Warranty EE eege dee 12 Liability Limitation e TE 12 Warranty E 19 FFF FU 12 Limitation of warranty lIabillll amp S ii xswa uru un kEiRKENAWE LEG NN UE FARW ADO NEU YR GENNAD YDYN UC R n 12 Returning a EE 12 1 INTRODUCTION RE 13 1 GE 13 12 el Ee een e FFF FEN YNN EHO NEF HE READ FFF FN NN YN WN NN 14 oa o E 14 14 PACKAGING 1MOMM a O Dui ei Gwi YGU O NEA GROW NOA OODD EF REU EA FR 14 1 5 Appearance and layout of elemenf S vvvvv eeuuuonuuuuunuuuunnLLLnn 15 2APUNCTIONAL OVERVIEW EE 18 KIC550 User Manual 2013 Fastwel Ver 0 03 3 KIC550 Storage Module Fastwel Lee Specification 2 1 CHOWAN diagrar E 18 eege 19 23 Op ration OF LED uii i nU EE 19 3 CONFIGURING STOR AGE DEVICES uegegeiecae eseou WU i A OS 22 3 1 Program configuration of the storage deviC6S v v
14. Fastwel dr KIC550 Storage Module User Manual Revision 0 03 The product described in this manual is compliant with all related CE standards KIC550 Storage Module Fastwel Lee Specification Product Title KIC550 Document name KIC 550 User Manual Manual version 0 03 Reference document IMEC 421459 550 Copyright 2012 2013 Fastwel Co Ltd All rights reserved Revision Record 0 01 Initial version of KIC550 User Manual KIC550 December 2012 Compliance with USB 2 0 specification The Hot Swap mode in this 0 02 version of the Module is not supported Meu February 2013 Compliance with USB 3 0 specification The Hot Swap function of KIC550 0 02 is supported if the specified function is also supported by the processor KIC550 July 2013 module Contact Information Fastwel Co Ltd Fastwel Corporation US Address 108 Profsoyuznaya st 55 Washington St 310 Moscow 117437 Brooklyn New York 11201 Russian Federation USA Tel 7 495 232 1681 1 718 554 3686 Fax 7 495 232 1654 1 718 797 0600 E mail info fastwel com sales fastwel com Web http www fastwel com FASTWEL Asia 6F No 118 Ln 235 Baogiao Rd Xindian Dist New Taipei City Taiwan R O C Tel 886 2 891 2 19 38 Fax 886 2 891 2 19 39 E mail asia fastwel com KIC550 User Manual 2013 Fastwel Ver 0 03 2 KIC550 Storage Module Fastwel Lee Specification TABLE OF CONTENTS VEO ONAN FF sa HR FFEFRIR YE R
15. Size DC WD1002FAEX HDD 1 WDC WD1002FAEX Nane Create Virtual Disk Do you want to create this virtual disk i es o Virtual disk configurations ENTER Select F10 Exit Save ESC Return 3 5 2 Virtual disc creation with HyperDuo technology Similar to the RAID process the HyperDuo virtual disc can be created using Configuration Wizard The creation of the virtual disc will reguire to have CFast memory card which is used as SSD as well as to have the 2 5 storage carrier installed Please select HBA 0 Marvell 0 in the Topology window and press Enter The dropdown widow will show an invitation to the Configuration Wizard mode Press Enter to continue KIC550 User Manual 2013 Fastwel Ver 0 03 31 KIC550 Storage Module Fastwel Lee Specification Marvell BIOS Setup c 2009 Marvell Technology Group Ltd Topology Information 1B4B Virtual Disks 9130 Free Physical Bl HDD O WDC WDIOD2FAEX BIOS Version 1 0 0 1029 HOD 1 WDC WDLOOZFAEX Firmware Version 2 2 0 1118 PCle Speed Rate 5 0Gbps Configure SATA as AHCI Mode Supported Mode RAIDO RAID1 Safe Capacity Help Marvell RAID on chip controller ENTER Operation F10 Exit Save ESC Return Use arrow keys to select available hard discs for creating the virtual disc Selection or de selection of the discs is made by the Space key CH When the storage device is selected symbol appears to the left of it Marvell BIOS Setup c 2009
16. Supported Mode RAIDO RAIDI Safe Capacity Help i Delete the selected virtual disk ENTER Operation F10 Exit Save ESC Return KIC550 User Manual 2013 Fastwel Ver 0 03 A4 KIC550 Storage Module Fastwel Lee Specification 4 Installation The KIC550 module is easy to install However it is necessary to strictly follow the rules warning notices and procedures below in order to properly install the device and to avoid damaging the product system components as well as avoiding injuries to the staff 4 1 Safety requirements While handling the KIC550 the safety requirements below should be strictly followed Fastwel Group is not responsible for any damages arising out of the failure to comply with such requirements Attention Since the Hot Swap function of KIC550 is available only if it is simultaneously supported by the processor module turn off the CompactPCl system power supply before installing the module into a free slot Violation of this rule poses a potential risk to your health and life as well as can lead to system or module damage Electrostatic Sensitive Device ESD The CompactPCI module contains elements sensitive to electrostatic discharges To prevent module damage it is necessary to comply with the following safety precautions Before touching the module discharge the electrostatic charge from clothing as well as from the tools before using them Do not touch electronic components
17. X Threshold 90 Next isk configurations ENTER Select F10 Exit Save ESC Return After that select Strip Size and press Enter In the dropdown menu with the options available for the specified RAID type select the required one and press Enter KIC550 User Manual 2013 Fastwel Ver 0 03 29 KIC550 Storage Module Fastwel Lee Specification Marvell BIOS Setup c 2009 Marvell Technology Group Ltd Configure gt Select free disksCreate Virtual Disk Virtual Disks Free Physical Disks e HDD DC WDIOO2FAEX HDD 1 WDC WD1002FAEX t Default Help Virtual disk configurations ENTER Select F10 Exit Save ESC Return After that select Name Enter a name of the virtual disc and press Enter to confirm Marvell BIOS Setup c 2009 Marvell Technology Group Ltd Configure gt Select free disksCreate Virtual Disk RAID Level RAID 1 Virtual Disks Free Physical Disks Stripe Size 64KB HDD WDC _WD1002FAEX HDD 1 WDC WD1002FAEX Meme MB Next Help Virtual disk configurations ENTER Select CORE Exit Save ESC Return Upon completion of the virtual disc configuration select Next and press Enter In the appeared system message window confirm the virtual disc creation by pressing Y The created virtual disc should appear in the list of Topology window KIC550 User Manual 2013 Fastwel Ver 0 03 30 KIC550 Storage Module Fastwel Lee Specification hnology Group Ltd RAID Level Stripe
18. and connector contacts If your workplace is provided with antistatic protection do not disregard the opportunity of using it KIC550 User Manual 2013 Fastwel Ver 0 03 45 KIC550 Storage Module Fastwel Lee Specification 4 2 Module installation procedure To install the KIC550 into the system follow the procedure below 1 Make sure that the safety requirements specified in the previous chapter are met Attention Non compliance with the following instruction can lead to module damages and system malfunction gt 2 Before installation make sure that the module has a configuration which corresponds to the application requirements see paragraph 3 Configuration of storage devices While installing the storage device you should consider the installation requirements outlined in subparagraph Attention Be careful when you determine the state of the SW1 1 switch in accordance with Table 3 1 and text of the paragraph 3 Attention Subsequent operations should be carried out with care avoiding damages to both KIC550 and other system devices gt DP 3 To install the KIC550 the following actions should be performed Before the installation make sure that the system power supply is switched off Attention While performing the following operation do not exert force when you insert the module connector into the mezzanine board connector To install the module into the connector use handle of the front panel gt
19. ase create backup copies of all the data before creation of the virtual disc Attention To prevent data loss on virtual disc storage carriers do not set the SW1 1 mode selector switch to the ON position 3 4 Configuration mode with BIOS Setup controller 88SE9130B The BIOS Setup helps to adjust basic operation parameters of the storage carriers Creation of the RAID virtual disc on the basis of the existing storage carriers Creation of the virtual disc using the Hyper Duo technology Verification of the storage carriers and virtual discs current states To enter the BIOS Setup you need to simultaneously press the CTRL M keys during the POST Power On Self Test procedure of the 88SE9130B controller KIC550 User Manual 2013 Fastwel Ver 0 03 25 KIC550 Storage Module F Specification Marvell 88SE91xx Adapter BIOS version 1 0 0 1029 PCI E X1 5 0Gbps Mode CPU AHCI Physical Disk 10 Disk Name speed Status 0 HDD WDC WDlOO02FAEX 3Gb s unconfi gured 1 HDD WDC wO1002FAEX 3Gb s unconfi gured Press lt Ctril gt lt to enter BIOS Setup or lt Space gt to continue_ The BIOS Setup requires using of the following keys t d J Navigation over menu items or lists of options G Selection of the menu item or given option Allow prohibit the given option D Return U Confirm Y or Reject N Save the settings and exit the BIOS Setup KIC550 User Manual 2013 Fastwel Ver 0
20. ee Table 5 3 Table 5 3 Parameters of climatic and mechanical effects CPC506 Type of the effect Parameter name Parameter value Document Change of Low temperature 40 C GOST 28209 89 IEC temperatures 68 2 14 84 With relative humidity High temperature 859C up to 80 no moisture condensation Sinusoidal vibration Frequency range Hz 10 500 GOST 28203 89 IEC Acceleration g 5 68 2 6 82 Single shocks Peak acceleration g 100 GOST 28213 89 IEC 68 2 27 87 Multiple shocks Peak acceleration g 50 GOST 28215 89 IEC Number of shocks 1000 68 2 29 87 given value is specified for the module that has no installed storage devices Where there is a conformal coating KIC550 is resistant to the impact of cyclic damp heat at the ambient temperature of 55 2 C relative humidity of 93 3 if the installed storage device corresponds to the declared conditions KIC550 when packaged is resistant to the ambient temperature changes in the range from 55 to 85 C with the relative humidity up to 80 with no moisture condensation in accordance with the IEC 68 2 14 84 standard Note The tested devices correspond to the declared requirements imposed to mechanical loads provided that the following conditions are met USB devices need to be fixed additionally e g fixed by mastic 5 5 MTBF The Mean Time Between Failures MTBF for ambient temperatures 30 C amount
21. el Ver 0 03 24 KIC550 Storage Module Fastwel Lee Specification 3 3 Marvell Hyper Duo function The Hyper Duo is a technology which helps to create a fast and inexpensive array using high capacity but rather slow storage carriers and CFast cards which support higher transfer rates but are rather expensive and have lower capacity Combining the solid state drive with a standard storage carrier into a single virtual disc the Marvell controller enables to reach the performance at the level up to 80 as compared to the parameters of a standard SSD This means that a user sees the storage devices as a single disc The Hyper Duo function has two operation modes Safe Mode This mode enables to create a virtual disc which is optimized for better resistance to failures In which case the virtual disc can be created with the storage carrier which already stores user data The virtual disc created in the safe mode can also be partially recovered if the data on CFast is damaged however the storage device data was not damaged at that time Capacity Mode This mode creates the virtual disc which is optimized for maximum use of SSD speed advantages Such virtual disc has a better performance in terms of reading writing operations as compared to the one created in the Safe Mode However in case of failure data on such a disc will be lost Attention While creating the virtual disc in the Capacity mode data on the storage carriers will be lost Ple
22. ery checklist The delivery checklist of KIC550 contains _ KIC550 Module 1 pcs _ Installation kit screws 4 pcs 1 pcs _ Antistatic bags for KIC550 Packages Note Maintain the module antistatic bag and consumer packaging in the original state prior to the end of the warranty period 1 4 Packaging information The KIC550 module is packaged in the box with dimensions 230x155x45mm Packaged module weight in kg no more than KIC550 User Manual 2013 Fastwel Ver 0 03 KIC550 Storage Module Fastwel Lee Specification 1 5 Appearance and layout of elements The following figures will help to identify components in terms of their configuration and functions Module hardware versions can have insignificant differences not indicated on diagrams and figures 1 5 1 Appearance of KIC550 Fig 1 1 Appearance of KIC550 with the installed storage device and memory card Compact PCI Serial connector Module ejector handle Storage device Switch to the Hot Swap mode CFast memory card The Figure demonstrates KIC550 module with the installed HDD and CFast card to be ordered separately The switch button to the Hot Swap mode also performs a mechanical function serves for installation de installation of the KIC550 module see subparagraph 4 2 Module installation procedure and 4 3 Module de installation procedure The Hot Swap function of the KIC550 module is available where this function
23. f KIC550 configurations by means of the SW1 1 switch Variation SW1 1 switch 2 5 storage SATA interface PCI Express number position see device interface Fig 3 1 1 OFF Independent of Not used 1 channel 2 5 the storage storage device device 277 channel CFast 2 ON Installed 2 5 device CFast Not installed CFast Not used Figure 3 1 Position of the SW1 1 mode selector switch of KIC550 21 2 1 fr m ON ON SW1 1 OFF SW1 1 ON KIC550 User Manual 2013 Fastwel Ver 0 03 22 KIC550 Storage Module Fastwel Lee Specification 3 1 Software configuration of storage devices Attention Additional functions of the 88SE9130B controller can be used only when the SW1 1 switch is in the OFF position SATA interface of the system module is NOT used Attention Additional functions of the 88SE9130B controller will not be available if the KIC550 module is installed into the slot not supporting the PCI express interface The main function of the the 88SE9130B controller is the PCI Express SATA bridge however it has other functions RAID 0 1 Marvell HyperDuo Controller additional functions are adjusted during system booting and by both Marvell Storage Utility designed for Windows OS and by BIOS built into the controller 3 2 RAID function Attention To avoid data loss on the generated RAID do not set the SW1 1 mode selector switch to the ON position In KIC5
24. he TY 4013 006 52415667 05 technical conditions provided that the Consumer complies with the operating storage transportation and installation conditions and procedures specified by the accompanying documents H The Manufacturer hereby guarantees that the products supplied thereby are free from defects in workmanship and materials provided operation and maintenance norms were observed during the currently established warranty period The Manufacturer s obligation under this warranty is to repair or replace free of charge any defective electronic component being a part of a returned product e Products that broke down through the Manufacturer s fault during the warranty period will be repaired free of charge Otherwise the Consumer will be invoiced as per the current labor remuneration rates and expendable materials cost Liability Limitation Right e The Manufacturer shall not be liable for the damage inflicted to the Consumer s property because of the product breakdown in the process of its utilization Warranty Period The warranty period for the products made by Fastwel LLC is 36 months since the sale date unless otherwise provided by the supply contract e The warranty period for the custom made products is 60 months since the sale date unless otherwise provided by the supply contract Limitation of warranty liabilities The above warranty liabilities shall not be applied e To the products including software which were repaired o
25. ice should be performed only by the employees who have sufficient gualification to do it Caution high voltage A Before installing the board into the system please make sure that the mains supply has been shut off In the course of installation repairs and maintenance of the device there is a serious risk of electric shock therefore always unplug the power cord at the time of operation This also refers to other feeder cables BOARD HANDLING PROCEDURES Electrostatic Sensitive Device ESD The electronic boards and their components are sensitive to the static electricity Therefore it is required to pay additional attention while handling these devices in order to ensure their safety and operability e Do not leave the board without a protective packaging in a non operating condition e lf possible always work with the board at workplaces protected against static electricity If it is not possible the user must discharge the static electricity before touching the device with hands or tools The most convenient way to do this is to touch the metal part of the system housing KIC550 User Manual 2013 Fastwel Ver 0 03 KIC550 Storage Module Fastwel Lee Specification General Board Operation Rules e To keep the warranty the product should not be altered or revised in any way Any alterations or improvements not authorized by Fastwel LLC except for those specified in this document or obtained from the technical support depart
26. ith the instructions for use with high voltage such as below re ER Attention The device is sensitive to the impact of static electricity This symbol and sign demonstrates that the electronic boards and their components are static sensitive which is why it is required to exercise caution while using this device and carry out inspections in order to guarantee integrity and operability of the device Attention Hot surface This symbol and sign warns you about the danger related to touching the hot surfaces of the device Attention This sign draws your attention to the User Manual aspects lack of understanding or ignoring of which may expose your health to danger or lead to the equipment damages Note This symbol is used for marking the text parts which require specific attention KIC550 User Manual 2013 Fastwel Ver 0 03 KIC550 Storage Module Fastwel Lee Specification Safety requirements This product of Fastwel LLC has been developed and tested in order to provide the compliance with the electric safety requirements Its design provides for a longtime failsafe operation The product life cycle can be sufficiently reduced due to its improper use during unpacking and installation process Therefore for the sake of your safety you ll need to comply with the below listed recommendations in order to provide the correct operation of the device HIGH VOLTAGE SAFE HANDLING PROCEDURES Attention All the works with this dev
27. le Table 5 2 KIC550 current consumption Power supply unit Maximum consumption current Average consumption current 12 Volt 400 mA 270 mA Consumption current without the hard disc drive and USB data storage device Connections of power supply lines should ensure minimum losses and guarantee stability of the performance characteristics Long feeding lines small section conductors and high resistance connections should be avoided While module consumes about 3 W the power supply unit should ensure the power allowance for the storage devices installed into the module and external passive devices connected to USB 3 0 interface 5 2 Compliance with KIC550 safety requirements The KIC550 module corresponds to the general safety requirements imposed to the information technology equipment according to the IEC 60950 2002 standard 5 3 KIC550 interference immunity KIC550 complies with the safety requirements related to the information technology equipment resistance to electromagnetic interference as defined in the CISPR 24 97 standard KIC550 corresponds to the requirements lodged to the industrial radio interference coming from the information technology equipment as defined in the CISPR 22 97 standard KIC550 User Manual 2013 Fastwel Ver 0 03 49 KIC550 Storage Module Fastwel Lee Specification 5 4 Operating conditions The device remains functional with the following climatic and mechanical effects s
28. liable computing systems 1 1 Module characteristics e Adapter for installation of 2 5 SATA storage device Supports HDDs with SATA and SATA II interfaces dimensions 100x70x9 5 mm 2 5 Supports RAID operation Supports the control of power supply of the storage device Supports the SGPIO interface indication of storage device states Availability of operation in slots with support of SATA and or PCI Express interfaces e USB 3 0 port USB 3 0 specification Protection against overload Rooted to the front panel CFast interface Corresponds to CFast Revision 1 1 specification 24 pin connector of N7G24 type manufactured by 3M company with the left side ejection unit Rooted to the front panel Availability of operation in slots with support of SATA and or PCI Express interfaces D Indication Status LEDs of the storage device Hot Swap mode indicator e Additional opportunities Support of the intra module RAID RAID 0 and RAID 1 Support of operation modes of HyperDuo storage devices Handle of KIC550 module ejector is equipped with a switch for implementation of the Hot Swap Mode e Forced cooling is not reguired e Supported standards _ SFF 8485 Specification for Serial GPIO SGPIO Bus PICMG 2 30 RC1 0 November 11 2009 PICMG CPCI S 0 R1 0 March 2 2011 CFast Specification Revision 1 1 Universal Serial Bus 3 0 Specification Rev 1 0 e Operating temperature
29. ment of Fastwel LLC as a set of instructions for their implementation cancel the warranty e This device should be installed and connected only to the systems meeting all the necessary technical and climatic reguirements This above is also true of the operating temperature range of a particular version of the board e While performing all the reguired operations for installation and adjustment please follow the instructions specified only in this document e Keep the original package for subseguent storage of the device and transportation in the warranty event If it is necessary to transport or store the board please pack it the same way as it was packed upon delivery e Exercise special care when unpacking and handling the device Act in accordance with the instructions given in the paragraph above KIC550 User Manual 2013 Fastwel Ver 0 03 KIC550 Storage Module Fastwel Lee Specification TRANSPORTATION UNPACKING AND STORAGE Transportation The module should be transported in a separate packaging box transport packaging of the manufacturing facility which consists of an individual antistatic bag and a cardboard box in the closed transport automobile railway air transportation in heated and pressurized compartments in storage conditions 5 defined in the GOST standard 15150 69 IEC 721 2 1 standard or in storage conditions 3 during sea transportation It is possible to transport modules packaged in individual antis
30. n order to let the contacts get into it up to the stop Fix the cover by screws After installation the cover can be sealed if necessary For this purpose one of the cover fixing screws has a cavity and additional holes for fixing the seal Note It is recommended to use the CFast cards labeled and formatted on this device 4 4 3 Connection of USB devices KIC550 supports the use of any PC peripheral USB devices of Plug amp Play standard e g keyboard mouse printer etc Note All the USB devices can be connected or disconnected when their power supply or power supply of the main system is switched on 4 5 Installation of software Drivers for the 88SE9130B controller and Marvell Storage Utility designed for Windows are stored on the following FTP server ftp ftp prosoft ru pub Hardware Fastwel CPx KIC550 KIC550 User Manual 2013 Fastwel Ver 0 03 48 KIC550 Storage Module Fastwel Lee Specification 5 Additional Information 5 1 Power consumption of KIC550 Power supply units used with KIC550 board should meet the following performance specifications Permissible range of the feed voltage values is provided according to the table Table 5 1 KIC550 power supply voltage range Power supply unit Minimum value Maximum value 12 V 10 8 V 13 2V Range of supply voltage variations A 10 Current consumption of the KIC550 board from the external power supply source is according to the tab
31. ogotype is a trademark belonging to Fastwel Group Co Ltd Moscow Russian Federation Besides this document may contain names corporate logotypes and trademarks being registered trademarks consequently property rights to them belong to their respective legitimate owners Ownership Rights This document contains information being the property of Fastwel Group Co Ltd It can neither be copied nor transferred with the utilization of Known media nor be stored in data storage and search systems without the prior written authorization of Fastwel Group Co Ltd To our best knowledge the data in this document does not contain errors However Fastwel Group Co Ltd cannot take responsibility for any inaccuracies and their consequences as well as responsibility arising as a result of utilization or application of any diagram product or example cited in this document Fastwel Group Co Ltd reserves the right to alter and update both this document and the product presented therein at its own discretion without additional notification KIC550 User Manual 2013 Fastwel Ver 0 03 7 KIC550 Storage Module Fastwel Lee Specification Notations Note This symbol and sign warns you about the dangers related to electric charges gt 60 V when touching the device or its parts Failure to comply with safety precautions specified or set by the regulations may endanger your life or health and could lead to product damages Please get acquainted w
32. or control is carried out in a semiautomatic mode One DIP Switch SW1 1 is used which is installed on the board 2 2 4 PCI Express bridge SATA 88SE9130 The PCI Express to SATA bridge is used to create two proprietary on board SATA Ui interfaces from x1 PCI Express Gen 2 0 interface This enables to simultaneously use both CFast and SATA storage devices on KIC550 module board This function also enables to organize the data storage where there is no standard SATA interface provided for Compact PCI Serial and PICMG 2 30 standards 2 2 5 USB The module has 1 USB 3 0 channel transmitting data from the processor module The USB port is rooted to the connector located on the front panel 2 3 Operation of LEDs KIC550 Module has 4 LED indicators rooted to the front panel Three LEDS ensure indication in accordance with the SFF 8485 specification One indicator is designed for visualization of the power supply control modes 2 3 1 SGPIO interface LEDs SGPIO interface LEDs are used to indicate the current status of the storage device connected to the SATA interface of the system module as well as the RAID operation mode which includes the physical storage device located on the KIC550 module In total there are three LED indicators see Table 2 1 Status of SGPIO LED indicators on the front panel of KIC550 1 ACT Activity a green LED which specifies that this storage device is addressed at this particular moment The Hot S
33. r were amended by the employees that do not represent the manufacturer Exceptions are the cases where the customer has made repairs or made amendments to the devices in the strict compliance with instructions preliminary agreed and approved by the manufacturer in writing e To the products broken down due to unacceptable polarity reversal to the opposite sign of the power supply improper operation transportation storage installation mounting or accident Returning a product for repair 1 Apply to Fastwel company or to any of the Fastwel s official representatives for the Product Return Authorization 2 Attach a failure inspection report with a product to be returned in the form accepted by the Manufacturer with a description of the failure circumstances and symptoms 3 Carefully package the product in the antistatic bag in which the product had been supplied Failure to package in antistatic material will VOID all warranties Then package the product in a safe container for shipping 4 The customer pays for shipping the product to Fastwel or to an official Fastwel representative or dealer KIC550 User Manual 2013 Fastwel Ver 0 03 KIC550 Storage Module Fastwel Lee Specification 1 INTRODUCTION KIC550 Storage Module expands functionalities of Compact PCI processor modules which correspond to PICMG 2 30 or Compact PCI Serial specifications The use of this board will enable the creation of high performance and highly re
34. rage Module Fastwel Le Specification Abbreviation Meaning loc Inter Intergrated Circuit LCD Liquid crystal display LPC Low Pin Count LVDS Low Voltage Differential Signal MDI Media Dependent Interface PC Personal Computer PIO Programmed Input Output PLCC Plastic Leaded Chip Carrier PM Peripheral Management Controller POST Power On Self Test PSB Processor System Bus RAMDAC Random Access Memory Digital to Analog Converter RTC Real Time Clock SMB System Management Bus SMBus System Management Bus SODIMM Small Outline Dual In Line Memory Module SSD Solid State Disk TFT Thin Film Transistor UART Universal Asynchronous Receiver Transmitter UHCI Universal Host Controller Interface USB Universal Serial Bus UTP Unshielded Twisted Pair KIC550 User Manual 2013 Fastwel Ver 0 03 52
35. range Industrial version 40 85 C e Resistance to the impact of cyclic damp heat when there is a conformal coating At the ambient air temperature of plus 55 2 C relative humidity 93 3 if the installed storage device corresponds to the declared conditions The Hot Swap function of the KIC550 module is available where this function is simultaneously supported by the processor module KIC550 User Manual 2013 Fastwel Ver 0 03 13 KIC550 Storage Module Fastwel Lee Specification Supply voltage 12 V Current consumption without HDD and USB storage devices 270 mA Shock vibration resistance 100g 5g this value is specified for the module without the storage devices installed D Mean Time Between Failures MTBF No less than 1000000 hours Weight no more than 135 grams Dimensions 130 6 mm x 213 0 mm x 20 3 mm Note Since the Hot Swap function of KIC550 is available in the event it is supported by the processor module turn off the power supply of CompactPCI system prior to installing the module into the available slot and prior to removal of the module from the slot see Paragraph 4 1 2 Ordering Information While applying the conformal coating to the KIC550 module the resistance to impact of cyclic damp heat is ensured provided that the installed storage device corresponds to the declared conditions Table 1 1 Information for KIC550 Coating COATED Conformal coating 1 3 Deliv
36. rties Marvell BIOS Setup c 2009 Marvell Technology Group Ltd Topology information HBA 0 Marvell 0 ID Virtual Disks Name Status HDD O WOC WD1002FAEX Stripe Size HDD 1 WODC WD1002FAEX RAID Mode Free Physical Disks Size G BGA Status BGA Rebuild Help Virtual Disk A set of disk blocks presented to an operating environment as a range of consecutively numbered logical blocks with disk like storage ENTER Operation F10 Exit Save ESC Return KIC550 User Manual 2013 Fastwel Ver 0 03 KIC550 Storage Module Fastwel Lee Specification 3 5 5 Deleting virtual disc The virtual disc can be deleted by using the BIOS Setup program of the 88SE9130B controller Attention The virtual disc delete function will erase all virtual disc data In Topology menu select Virtual Disks Test In the dropdown menu select Delete In the appeared system message window Do you want to delete this virtual disk confirm the virtual disc deleting by pressing Y In the appeared system message window Do you want to delete MBR from this virtual disk confirm the deleting the virtual disc Master Boot Record by pressing Y Marvell BIOS Setup c 2009 Marvell Technology Group Ltd Topology Information HBA 0 Marvell O Vendor ID 1848 Virtual Disks Device ID 9130 ision ID B1 Version 1 0 0 1029 HDD 1 WOC WD1002 ware Version 2 2 0 1118 Free Physical Disks PCIe Speed Rate 5 0Gbps Configure SATA as AHCI ode
37. s to no less than 1000000 hours The MTBF values are calculated according to the Telcordia Issue 1 calculation model calculation procedure Method Case 3 for continuous operation when the device is located on the ground under conditions corresponding to the Moderately Cold Climate category as defined in the GOST standard 15150 69 at the ambient temperature 30 C KIC550 User Manual 2013 Fastwel Ver 0 03 50 KIC550 Storage Module Annex A Fastwel Le Specification Useful Abbreviations Acronyms and Short cuts Abbreviation Meaning ACPI Advanced Configuration and Power Interface AGP Accelerated Graphics Port AGTL Advanced Gunning Transceiver Logic BIOS Basic Input Output System BMC Baseboard Management Controller CRT display Cathode Ray Tube Display DAC Digital Analog Converter DDR SDRAM Double Data Rate Synchronous Dynamic Random Access Memory DMA Direct Memory Access DMI Direct Media Interface DVMT Dynamic Video Memory Technology ECC Error Correction Code EEPROM Electrically Erasable Programmable Read Only Memory EHCI Enhanced Host Controller Interface Universal Serial Bus specification EIDE Enhanced Integrated Drive Electronics EOS Electrical Overstress ESD Electrostatically Sensitive Device Electrostatic Discharge FSB Freguency System Bus FWH Firmware Hub KIC550 User Manual 2013 Fastwel Ver 0 03 KIC550 Sto
38. tatic packages in multiple packaging transport packaging of the manufacturing facility The packaged modules should be transported in accordance with the shipping rules operating with this particular type of transport During handling and transportation operations the packaged modules should not undergo sharp pounding falls shocks and exposure to atmospheric precipitation The packaged modules should be stored in a carrier vehicle in such a manner which will prevent their moving Unpacking Prior to unpacking before transportation at subzero temperature of ambient air the modules should be kept within 6 hours under storage conditions 1 defined in the GOST standard 15150 69 IEC 721 2 1 standard It is prohibited to place the packaged module close to the heat source prior to unpacking While unpacking it is required to comply with all safety precautions which ensure its safety as well as marketable condition of consumer packaging of the manufacturing company At the time of unpacking it is required to check the module that it has no external mechanical damages after transportation Storage Module storage conditions for group 1 are defined in the GOST standard 15150 69 IEC 721 2 1 standard KIC550 User Manual 2013 Fastwel Ver 0 03 11 KIC550 Storage Module Fastwel Lee Specification MANUFACTURER S WAARRANTY Warranty Liabilities e The Manufacturer hereby guarantees the product conformity with the requirements of t
39. twel Ver 0 03 17 KIC550 Storage Module Fastwel Lee Specification 2 Functional overview 2 1 Functional diagram Fig 2 1 Block diagram of KIC550 PCIE Redriver i H SN65LVPE501 Bridge 88SE9130 i l l l l SATA Switch PD2DBS212 SATA SATA SATA Redriver Redriver Redriver a i SN75LVCP600 SN75LVCP600 SN75LVCP600 l l SATA i Interface l CFast Interface i i Se l Front Panel l l l USB l Power come E lach i i l I FAIL Y LED Di f USBSO j Port i Of gt LED Microcontroller l SGPIO l l We Hot Swap l bow 1 Switch Compact PCI Ve u Serial Connector P1 KIC550 User Manual 2013 Fastwel Ver 0 03 18 KIC550 Storage Module Fastwel Lee Specification 2 2 Functional parts overview 2 2 1 Microcontroller The microcontroller serves for exchanging data with host controller via SGPIO protocol and is meant for implementation of monitoring function of the supply voltage and the Hot Swap function support 8 bit microcontroller Atmel ATMega 8 16l is used 2 2 2 Power Switch Powerful P channel key operated by the microcontroller 2 2 3 SATA multiplexors SATA Switch PIZDBS212ZHE SATA multiplexor ensures switching of SATA HDD or CFast over input interfaces depending on functionality of a particular peripheral slot Multiplex
40. v v lt kekesaon 23 3 2 RAID TOU CHON sn Ri O dw non N i i n dai fi A Y aa 23 od Marvell Hyper Duo TUNCHON yna UR do FA ROD ni SEO Enwi Cd RAA 25 3 4 Configuration mode using BIOS Setup controller 88SE9130B v v lt lt 25 3 9 Cr ati n Of virtual E 27 GI ue EN lei ME 45 E 45 242 KIGS5SO Installation ee Beiau YG i ONCE RD Ga DUR AR BA RR 46 4 3 Module demounting e UE 47 4 4 Installation of storage COVICCS a icsncn ctictcewadcnssmianeicens ntaxpedneeenenateciuadaeeranedengdese 47 e EE 48 5 ADDITIONAL INFORMATION 49 5 1 Power consumption of KIC BO uii EGG Oia nU RF DDOL REED Ga N OO 49 5 2 Compliance with KIC550 safety reguiremen S v 9 v vereuo 49 5 3 KIC550 interference IMMUN sees xii hates GG UG ASSEN ENEE 49 5 4 Operating Conditions a GR O NOE UD Fd MC yR OR RR OEOD ML 50 LR 50 ANNEX A Useful Abbreviations Acronyms and Short cutS eun 51 KIC550 User Manual 2013 Fastwel Ver 0 03 KIC550 Storage Module Fastwel Lee Specification List of tables Table TT Information Tor E 14 Table 2 1 Status of SGPIO LEDs on the front panel of KICBbO LLYRY LLYFR eee ee tees eeeee eee 20 Table 2 2 Status of HS blue LED au sic scccsends cot Sege deg ENEE SA SEENEN DO nad AE EES EEN EE RAA 20 Table 3 1 Possible options of KIC550 configurations by using the SW1 1 switch 9 9 99 eeren inner i nenu 22 Table 5 1 KIC550
41. ved from the system KIC550 User Manual 2013 Fastwel Ver 0 03 21 Fastwel o KIC550 Storage Module Specification 3 Configuring of the storage devices The KIC550 module helps to perform flexible adjustment of the storage devices with due consideration of the system specific features The storage devices installed on the KIC550 module hereinafter referred to as the Carrier can be connected to the system module SATA or PCI Express interfaces according to the Compact PCI Serial and PICMG 2 30 specifications If there is connection to the PCI Express interface Marvell controller 88SE9130B built into the PCI Express SATA storage device will be used If SATA interface of the system module is not used SW1 1 switch is in the OFF position both storage devices are connected to SATA channels of the PCI Express SATA controller If SATA interface of the system module is used SW1 1 switch is in the ON position and the 2 5 storage device is installed then the SATA interface is connected to the 2 5 storage device and the first PCI Express channel of the SATA controller is connected to the CFast memory card H during the use of the SATA interface of the system module the 2 5 storage device is not installed then the SATA interface is connected to the CFast memory card The table below describes possible variations of carrier configurations by means of the SW1 1 switch Table 3 1 Possible variations o
42. wap function of the KIC550 module is available where it is simultaneously supported by the processor module KIC550 User Manual 2013 Fastwel Ver 0 03 19 KIC550 Storage Module Fastwel Lee Specification 1 FAIL Failure red LED indicator showing that RAID has switched to the Degrade mode Flashing of FAIL LED with the constant frequency of about 1 Hz indicates that RAID performs the Rebuild procedure The constant flashing of FAIL LED alongside the flashing of the blue HS LED indicates that the ejection of KIC550 module is not available at this particular moment 2 HS two color LED indicator The green LED light corresponds to the Locate LED function of the SGPIO interface The specified LED enables to identify this storage device The blue light is described in the subparagraph 2 3 2 HS blue LED indicator of power supply control modes Table 2 1 Status of SGPIO LEDs on the front panel of KIC550 LED Device status LED response Note ACT green Addressing to the Flashing while being storage device addressed RAID error Constantly on S RAID rebuild Flashing with 1 Hz Device ejection from Constantly on Only with the the crate if prohibited simultaneously flashing blue HS LED indicator Supported only with the Hot Swap driver Operating condition Off Locate LED HS Storage device Flashing with 1 Hz green identification 2 3 2 HS blue LED indicator of the power suppl
43. wn eject the module from the mezzanine board connector see Fig 1 1 6 After the module has been ejected from the mezzanine board connector remove it from the crate using the guide rails 4 4 Installation of storage devices 4 4 1 Installation of 2 5 storage carrier External view of KIC550 with the installed 2 5 storage carrier and memory card is shown on Fig 1 1 The 2 5 storage carrier is connected to XS3 connector and is fixed with the screws supplied in the installation kit holes A D on Fig 1 2 To comply with the preset dimensions the 2 5 storage carriers should be installed into the module without the use of lock washers In this case locking should be ensured by using sealant or paint in accordance with the Industrial Standard 07 460091 014 2004 The Hot Swap function of KIC550 is available when it is simultaneously supported by the processor module KIC550 User Manual 2013 Fastwel Ver 0 03 47 KIC550 Storage Module Fastwel Lee Specification 4 4 2 Installation of CFAST memory cards Module KIC550 is equipped with XS2 connector for CFast memory card External view of the CFast connector is shown on Fig 1 2 Note It is not allowed to remove or connect CFast memory cards on the KIC550 when its power supply power is switched on Remove the screws of the CFast cover on the front panel and carefully insert the properly positioned CFast card into the connector along the guide rails and gently press on it i
44. y control modes HS the Hot Swap blue LED indicates that the Hot Swap mode has been activated In order to properly remove the KIC550 module from the system during its operation it is required to activate the module ejector handle In which case the HS LED starts to flash with a frequency of 1 Hz The KIC550 module remains in this state until it receives the confirmation from the system module that the ejection is available If the confirmation is received the HS LED is constantly on and the module can be removed If there is no confirmation then after 30 seconds the FAIL LED will be on In which case the ejection procedure can t be performed and the handle needs to be brought back to the initial position The table of working combinations of HS blue LED is stated below Table 2 2 Status of HS blue LED System supply HS LED status Module operation mode System is shut down Off Switched off Off Switched on Standard functioning The Hot Swap function of the KIC550 module is available where this function is simultaneously supported by the processor module KIC550 User Manual 2013 Fastwel Ver 0 03 20 KIC550 Storage Module Fastwel LE Specification System is on Flashing with 1 Hz frequency Awaiting system module permission for ejection from the system Constantly on The module power supply is switched off The storage devices have been stopped The module can be remo
45. ysical List and select a new disc after which press the Space key Press Enter to continue the process KIC550 User Manual 2013 Fastwel Ver 0 03 41 KIC550 Storage Module Fastwel Lee Specification Marvell BIOS Setup c 2009 Marvell Technology Group Ltd i Rebuild gt Select free disks Information HBA O Marvell O Port ID 0 Virtual Disks PD ID D L Test Type SATA PD LHDD 1 WDC WD1002FAEX Status Unconfigured Free Physical Disks Size 95386948B Feature Support WCQ 66 48Bits Current Speed 66 Model WOC WD1002FAEX 0073A0 Serial WD ABCDE1234567 FW Version 05 12321 Help Use the space bar to select the free disks to be used in the array ENTER Operation i Select F10 Exit Save ESC Return In the appeared system message window confirm the virtual disc rebuild process by Dressing Y KIC550 User Manual 2013 Fastwel Ver 0 03 KIC550 Storage Module Fastwel Lee Specification Marvell BIOS Setup c 2009 Marvell Technology Group Ltd Rebuild gt Select free disks Information Marv Port ID O Virtual Disks PD ID D LTest Type SATA PD L WDC N Status Unconfigured Free Physical Disks Size 95386 LHDD O WDC WD1002FAEX Feature Support WCQ 66 48Bits Help Use the space bar to select the free disks to be used in the array ENTER Operation SPACE Select F10 Exit Save ESC Return State of the virtual disc rebuild process is displayed in the virtual disc prope
Download Pdf Manuals
Related Search