Home

¥ Liberty (520) Manual

1. CLEAN THE BRASS IF NECESSARY If your appliance has a brass door it may be cleaned using a non abrasive polish such as FLITZ when the appliance is cool The brass trim and ashlip is anodized and should be cleaned with soap and water CHECK FOR CREOSOTE BUILDUP Creosote buildup should be checked twice monthly during the heating season Either look down the chimney from the top or remove a chimney connector section Any more than 1 4 of buildup requires chimney cleaning Creosote develops quickest when burning at a low temperature or when burning un seasoned wood When wood is burned slowly it produces tar and other vapors which combine with moisture to form creosote Creosote vapors condense in the relatively cool chimney flue and creosote residue accumulates on the flue lining When ignited this creosote makes an extremely hot fire pace24 MAINTAINING YOUR APPLIANCE CONTINUED DOOR AND GLASS INSPECTION The door must seal air tight for the appliance to work correctly Check the two items below and follow the appropriate remedy to fix any problems e Check the door cam operation When closed the door cam should pull the door against the face of the appliance but not be so tight as to not allow the handle to point downwards If the operation is not correct see the section Adjusting the Door Cam below e Remove the door by opening it and lifting it off the hinges Place th
2. MAINTAINING YOUR APPLIANCE CONTINUED pace 25 Replacing the Door Gasket Remove the door by opening it and lifting it off the hinges Remove the old gasket by stripping it away with a screwdriver or other tool see the illustration below Apply a line of gasket cement available from your dealer in the groove that follows the perimeter of the door Insert the gasket into the groove Do not stretch the gasket as you place it into the groove Cut off any excess gasket when done Allow 2 hours for the cement to dry When re installing the door the gasket may need to be flattened by repeatedly opening and closing the door Replacing the Glass or Glass Gasket Remove the door by opening it and lifting it off the hinges Remove the door handle from the door Then remove the glass retainer by unscrewing the ten screws that hold it in place with a 5 16 nutdriver see the illustration below Carefully remove the glass Make sure the 3 4 black channel tape new or old runs around the perimeter of the glass If using a new gasket trim off any excess Place the glass new or old in place so there is a small gap between the edge of the glass and the door frame Make sure the gasket is tucked underneath the glass so the glass does not touch the door frame Place the glass retainer in place and secure it with the screws removed earlier Make sure the white gasket stays in place and seals the window Tighten the glass retainer until the gaskets st
3. Block Off Plate Template 2 Flanges i Measurement Damper for attaching the block off Measurement The center of the flue is 9 1 4 back from the fireplace opening Measurement B Mark the location where the flue exits 6 1 4 in diameter Pace16 OPERATING YOUR APPLIANCE SAFETY NOTICE If this appliance is improperly operated a house fire may result For your safety read the directions below and the Safety Precautions listed on pages 2 and 3 prior to operating this appliance e If you have any questions regarding the operation of this appliance contact your dealer Building a fire in disregard of the information provided in this section can cause permanent damage to your appliance and void your warranty Never use gasoline lantern fuel kerosene charcoal lighter fluid or similar liquids to start of freshen up a fire in this appliance Keep these liquids well away from the appliance Keep furnishings and other combustible materials away from the appliance PAINT CURING The paint on this stove cures under heat Start a small fire and burn at a low rate for the first fire You will notice fumes and smoke from the paint curing and oil burning off the steel This is normal We recommend you open windows to vent the room ASH REMOVAL Ashes should be placed in a metal container with a tight fitting lid
4. PAGE 8 STOVE INSTALLATION CONT OPTIONAL EQUIPMENT REQUIREMENTS See Optional Equipment on page 33 Must be installed with either the optional legs or pedestal FACTORY BUILT CHIMNEY REQUIREMENTS Chimney connector must be a minimum 24 MSG black or 26 MSG blued steel Use 6 diameter type HT chimney from one manufacturer do not mix brands Chimney must be used from the first floor or wall penetration to the chimney cap Chimney connector and chimney must be fastened to the stove and each adjoining section Follow the chimney manufacturer s clearances and requirements Use the chimney manufacturer s fire stops attic guards roof supports and flashings when passing through a ceiling or thimble when passing through a combustible wall Minimum height of 15 feet NOTE External factors may adversely affect draft see Drafting Performance below In these cases additional chimney height may be required to boost draft Maximum height of 33 feet No more than 180 of elbows two 90 elbows or two 45 amp one 90 elbow etc NOTE Additional elbows may be allowed if draft is sufficient Whenever elbows are used the draft is adversely affected Additional chimney height may be required to boost draft Chimney Cap oO I See the section Chimney Termination Requirements for more details Minimum System 15 Maximum System 33 Roof Penetration Equipment Roof Radiation Shield Factory Built Flashing St
5. cceeceeeeeeteeeeettees 23 Chimney Termination Requirements eeee 9 Chimney Requirement ccccceeeeeeeeeeseeeeneeeneees 8 ClearanCes isin lid ee Gece 7 Creosote Buildup Check 0 eceeeceeeeeeeeeeeeeeeseeeeeeeeeaes 23 DIM NSIONS 3 a el eeaieded eae Adie 5 Door Cam AdjuStment c cecceeeceeeeeseeeeeeeeeeeetneeeneees 24 Door Gasket Replacement ceccceeeseteeeeteeeeeeeneeeee 25 Door Hinge Lubrication i e 25 Door INSP6Ction 2 ntina Altes 24 EMIClONCY wes ci A oe A ies 5 Emissions Phase II Approved 5 EPA Emissions Phase I Approved seee 5 Exterior Chimney Stove c cecceeseeseeeeeeeseeeeseeeeeees 13 Factory Built Chimney Requirements eeee 8 Fan Operation x icicniei nay iene 20 Features amp Specifications 0 0 cceeeeeeeeeeeeteeeeeeeeneees 5 FirGDOX SIZ cc hits eseceeac ed lecestesuacteeepathstedtieaviendaieneceel 5 Firebrick And Baffle Inspection And Cleaning 26 Firebrick Removal and Replacement Inst 24 Floor Protections nn nities Ae eee ens 7 Flue Size 6 artien kid ieee eed deed ee 5 Fihi iret Ge tee oats 21 Glass Cleaning isis yi ieed whittlin ats 23 Glass INSP CTION cceceeeceeeeeeeeeeteeeeeeteaeeteeeeeaeeteaees 24 Glass or Glass Gasket Replacement ceeeee 25 Hearth Stove starting ON Page eeeeeeeeeeeeeeeeeeeeee 13 Heating Capacity cecceecseeesseeeeneeteeeeeeeetseeseeeeneees 5 Int
6. ecceeeeeeeeeeeeeeeeeneeenees 5 Stove Installation Before YOu BeGin cccesscceeseseeseseeeeesseeeeneneeeeneees 6 Planning The Installation 6 Preparation for Installation eeseeeeeseeeeseeeeeeneees 6 Stove Installation Considerations ceeeeeeee 6 Stove Placement Requirement ceeeeeeeee 7 Floor Protection Requirement cccesseeeeneeeeees 7 Optional Equipment Requirements 0 ce 8 Factory Built Chimney Requirements 0 008 8 Chimney Termination Requirements eeee 9 Outside Air Requirement ccceeeeseeeeeeeeeeeeneees 9 Alcove Installation Requirement e 10 Mobile Home Requirement n e 11 INSTALLATION DIAGRAMS Standard Ceiling with a Factory Built Chimney 12 Cathedral Ceiling with a Factory Built Chimney 12 Exterior Factory Built Chimney ceeeeeees 13 Hearth Stove Positive Connection cceee 13 Hearth Stove Direct Connection ceeeee 14 Hearth Stove Horizontal Connection 14 Block Off Plate Installation ceceeeeeeeeseeeees 15 Operating Your Appliance Before YOu BeGin s cccesceceeseseeseseeeeesseeesseneeerseees 16 Paint GUNG cs iven geist esiratas 16 Location Of Controls cccecceeeeeeeeeseeeeeeeeteeeeeeeteaeens 16 Approximate Air Control Settings ceeee 16 Bypass Control vvcesie heieri 17 Learning to Burn your Appliance 17 How to Start a
7. x Ay _ T Hil E t ie El F Liberty Owner s Manual May 2001 e Residential Freestanding Stove e Mobile Home Freestanding Stove e Alcove Approved SAFETY NOTICE If this appliance is not properly installed a house fire may result For your safety follow the installation directions Contact local building or fire officials about restrictions and installation inspection requirements in your area Liberty Wood Stove GANT Ind Warnock Hersey Inc Vv VY lt gt 10850 117th Place N E Kirkland WA 98033 F Listed Part 93508013 10 00 INTRODUCTION amp IMPORTANT INFORMATION Pacet Introduction We welcome you as a new owner of a Lopi Liberty wood burning appliance In purchasing a Lopi Liberty you have joined the growing ranks of concerned individuals whose selection of an energy system reflects both a concern for the environment and aesthetics The Lopi Liberty is one of the finest appliances the world over This manual will explain the installation operation and maintenance of this appliance Please familiarize yourself with the Owner s Manual before operating your appliance and save the manual for future reference Included are helpful hints and suggestions which will make the installation and operation of your new appliance an easier and more enjoyable experience We offer our continual support and guidance to help you achieve the maximum benefit and enjoyment from your appliance Importan
8. 10850 117th PI N E Kirkland YA 98033 OPTIONAL EQUIPMENT Rear blower electrical rating 115V Replace glass only with LOPI supplied NEOCERAM ceramic 60 Hz 1 8 Amps glass 5mm U S ENVIRONMENTAL PROTECTION AGENCY Certified to comply with July 1990 particulate emission standards DATE OF MANUFACTURE 1997 1998 1999 Jan Feb Mar Apr May June July Aug Sep Oct Nov Dec EEEE i L EEHEHE E E OPTIONAL EQUIPMENT pace33 STOVE LEGS INSTALLATION BRASS 99200500 CAST BLACK 99200800 BLACK STEEL 99200100 There are three different stove legs available for your wood stove cast brass cast black and black steel The instructions for installing the legs are the same for each type of leg Raise the stove by inserting some pieces of lumber in the middle of the stove to a height of about 8 Line up the hole in the top of the leg with the threaded bolt hole in each corner of the stove bottom Using a 9 16 open end or socket wrench fasten the leg to the stove with the supplied attachment bolts and washers making sure the legs are flush with the corners of the stove Unscrew the leveling bolts enough so the stove will rest on the upper tips not the metal portion of the legs Lower the stove down Attach each leg to the stove by inserting a bolt and washer through the hole or slot in the leg and into the threaded hole on the stove Use a 9 16 socket wrench to tighten S S eo pear z j emcee J pf z eo
9. For good results YOU MUST OBTAIN AN INTENSE FIRE BEFORE CLOSING THE AIR CONTROL DOWN The steps below detail one method for starting a fire 1 Pile several pieces of kindling on top of newspaper or a fire starter in the center of the firebox it is better to have too much kindling than not enough Place two medium sized pieces of wood on either side of kindling laying front to back 2 Make sure the air control is fully open push all the way in and the bypass opened pull all the way out Start the newspaper or fire starter Note you may want to crack the door during starting to allow for more air 3 Allow the kindling to start and burn Then place another medium size piece of wood on top of the burning kindling so that it straddles the two medium pieces and close the door This arrangement takes advantage of the air inlet located in the center under the door to feed the fire with adequate oxygen You may notice the flames burning from the front to the back 4 Let the fire burn at least 15 minutes before closing the bypass Wait at least 30 minutes or until the appliance is fully hot before closing the air control down paceis OPERATING YOUR APPLIANCE CONTINUED How to Reload Your Appliance When reloading your appliance you can avoid smoke entering the room by following the steps below 1 Push the air control all the way in so the fire starts to burn quickly helping draft 2 Pull the bypass out all the way and wait 30 se
10. The closed container of ashes should be placed on a noncombustible floor or on the ground away from all combustible materials pending final disposal Ashes should be retained in the closed container until all cinders have thoroughly cooled LOCATION OF CONTROLS To open turn the handle DOOR HANDLE counter clockwise and swing the door forward Slide out to close down the amount of air into the firebox for a Slide in to allow more air into the firebox for a faster rate of slower rate burn nN of burn nn A 4 BYPASS CONTROL AOU Pull the bypass out AIR CONTROL for loading amp starting Push the bypass in during burning e Do not open the door when the air control is closed This may result in a sudden flash of flames as the fire ignites with oxygen However this appliance has been designed to reduce this possibility e The controls become hot during operation use a glove or other device if necessary e Open the door for refueling only do not operate with the door open or removed Approximate Air Control Settings Overnight Burn 06 Fully out to 9 32 open Medium Burm c eeee 9 32 open to 5 16 open Medium High Burn 5 16 open to 7 16 open High BUT soms teeta 7 16 open to pushed fully in OPERATING YOUR APPLIANCE CONTINUED pace 17 Bypass Control The bypass control is located on the right side of the s
11. between the pieces I Nj v pace22 OPERATING YOUR APPLIANCE CONTINUED A WORD ABOUT WOOD CONTINUED Sheet Metal Roofing 2x4 Purlins 2x6x12 Rafter Constructing a Wood Shed ah on The drawing to the right details the lt M ee Roste a 8 Apart construction of an inexpensive wood shed DE aaar i that will promote drying increasing the heat output from your wood 8 Width et Depth What Type of Wood is Best Choosing the kind of firewood to burn in your appliance depends on what is available to you Softwoods such as pine or fir ignite and burn quicker but require more frequent loadings and are less suited for overnight burns For longer burns with less frequent loadings we recommend harder woods such as oak or maple The chart below details the BTU heat output of the various species Note the higher BTU output of the harder woods The best arrangement is to have softwoods for starting and immediate heating and hardwoods for overnight and sustained burns SPECIES LBS CORD BTU s CORD Hours per Cord at 40 000 BTU s per Hour Approximate 20 moisture Approximate Approximate ALDER 19 050 000 APPLE 33 000 000 ASH 25 800 000 BIRCH 22 800 000 CEDAR 15 450 000 COTTONWOOD 16 200 000 DOGWOOD 31 725 000 ELM 16 950 000 FIR DOUGLAS 22 275 000 HEMLOCK 20 250 000 MAPLE 24 000 000 OAK RED 27 600 000 OAK WHIT
12. Hot Fire Quickly 0 ee 17 How to Reload Your Appliance eee 18 How to Adjust the Heat Output Precisely 18 How to Obtain an Overnight Burn sses 19 Good Burning Habits 0 0 00 eceeeeeeeeeeteeeeneeeees 19 Blower Operation ceccccsceeeeeeeseeseeeeeeeteaeeeeeetsaees 20 When to turn the blower ON seeen 20 Blower COntrols cccessceeeeseeeeeeeeeeesneeeeeneeereaes 20 How to Use the Blower to Regulate Heat 20 A Word about Wood cc essseeeeseeeseneeeeeneeeteneeereneees 21 The Drier the Better eseceeeseseessseeeeseeeeresees 21 How to Dry and Store Wood sses 21 Constructing a Wood Shed ceeeeeseeseeeeeeeeee 22 What Type of Wood is Best 22 How to Buy Wood 1 0 0 eeeeeeeeeeeeeneeeeeeeeeteneeeeeeeeeees 22 Don t Burn Scraps Garbage Wax Logs etc 22 Maintaining Your Appliance Maintenance Schedule ecceeeceeeseeeeeeeteeeeeeeeaees 23 Remove Ash From The Firebox eee 23 Clean The Viewing Glass cccceeeeeeeeeeeeeeeeeeeetes 23 Clean The Brass ci cieccsicsctsegseeceiidieiesstiacneaeeeuzegeaesee 23 Check For Creosote Buildup ceceeseeseeeteeeereee 23 Door And Glass Inspection c cecceeeeeeeeteeeneeeees 24 Adjusting the Door Cam sesser 24 Replacing the Door Gasket ecceeeeeeeeeeeees 25 Replacing the Glass or Glass Gasket 0 25 Lubricate The Door HINge eese 25 TOUChH Up P
13. through the vents along the top of the stove Operating instructions are on page 20 The directions below detail its installation 1 Feed the two wires from the thermodisk assembly through the space between the stove and rear heat shield Insert the thermodisk assembly into this space until the top portion hooks the top edge of the rear heat shield see the illustration below The thermodisk should fit tight in the channel If it does not remove it and bend the metal support down to insure a snug fit Slide the thermodisk This portion assembly into hooks on the the space top edge of the between the rear heat shield stove and rear heat shield Thermodisk Wire Clip Run both of the i wires from the This portion of the wire thermodisk down clips slides over the behind the stove j rear heat shield and through the eye of the wire clip The wires pass through the eye of the wire clip The two yellow wires attach to the thermodisk Blower Box Three holes for attaching the blower box to the Power Cord back of the stove exits from back of blower box 2 Slide the wire clip over the rear heat shield Run the two wires from the thermodisk assembly through the wire clip and pull the slack wire out of the stove The wires coming from the thermodisk assembly must not have any slack these wires may cause a short if the wires come in contact with the firebox Remove enough slack to eliminate the wires rubbi
14. 12 hours may be obtained with a small amount of coals left over in the morning if the right steps are taken 1 Establish a hot fire 2 Fill the appliance with large pieces of wood preferably hardwoods like oak or maple 3 Let the wood burn on high for 20 to 30 minutes to allow the new pieces of wood to catch fire and burn off any moisture 4 Pull the air control out to a low setting HINT You want an air control position that is the farthest in yet still allows coals to be left in the morning Experiment using air control positions that are farther and farther in until a suitable position is found 5 In the morning break down the coals and lay kindling and small pieces of wood on top of the coals to re establish the fire NOTE Even the smallest amount of coals can start a new fire easily because of all the heat energy stored in the firebrick If there are no coals left yet the appliance is hot you will find starting a new fire will be much easier and the appliance will start giving off heat much quicker than if started cold Let the appliance burn at least 20 minutes on high after loading This allows the appliance to reach the most efficient operating temperature a Even the smallest amount of coals can re start the appliance Good Burning Habits Increased efficiency reduced emissions and less creosote are the rewards of good burning habits The items below list good habits to establish with your
15. CAUTIONS CONTINUED Never try to repair or replace any part of this appliance unless instructions are given in this manual All other work must be done by a trained technician Allow the appliance to cool before carrying out any maintenance or cleaning Maintain the door and glass seal and keep them in good condition Avoid placing wood against the glass when loading Do not slam the door or strike the glass Do not throw this manual away This manual has important operating and maintenance instructions that you will need at a later time Always follow the instructions in this manual WY amp PAGE 3 Do not make any changes or modifications to an existing masonry fireplace or chimney to install this appliance Do not make any changes to the appliance to increase combustion air Overfiring the appliance may cause a house fire If a unit or chimney connector glows you are overfiring Do not use a grate or other device to elevate the fire off of the firebox floor Burn the fire directly on the bricks Travis Industries Inc grants no warranty implied or stated for the installation or maintenance of your appliance and assumes no responsibility of any consequential damage s PAGE 4 TABLE OF CONTENTS General Information Introduction amp Important Information eee 1 Safety Precautions cccesceeseseeeeseeeeeeeeseeeeeeeaes 2 Features amp Specifications
16. Capacity in square feet 1500 to 2500 Maximum BTU s per Hour Cord Wood Calculation 74 300 Overall Efficiency Oregon Method 70 Maximum Burn Time Hours 12 Heating capacity will vary depending on the home s floor plan degree of insulation and the outside temperature It is also affected by the quality and moisture level of the fuel Dimensions ee Width i Flue Location Of Stove Weight 6 Diameter flue is With Legs 470 Lbs centered on the A stove and 6 1 4 from the back edge of the stove top Depth NOTE From Back Edge of Stove Measure all Top to Faceplate clearances Ashlip Depth from the edge of the stove top With Black Steel Legs 30 7 8 With Cast or Brass Legs 32 1 4 With Pedestal Emissions 2 6 Grams Per Hour EPA Phase II Approved Tests conducted by E E S P C Lab paces STOVE INSTALLATION SAFETY NOTICE If this appliance is not properly installed a house fire may result For your safety follow the installation directions Contact local building or fire officials about restrictions and installation inspection requirements in your area e Check with local building officials for any permits required for installation of this stove and notify your insurance company before proceeding with installation PLANNING THE INSTALLATION HINT We suggest that you have an authorized Travis Industries dealer install your stove If you install the stove yo
17. E 31 500 000 PINE 16 875 000 REDWOOD 18 000 000 SPRUCE 16 800 000 How to Buy Wood Wood is sold by the cord 4 wide by 4 high by 8 long Buy wood in the spring and summer when prices are lower and it will have plenty of time to dry If buying in winter have the wood moisture tested test several pieces You will receive up to 25 more heat from a cord of dry wood than from wet or green wood Rotate your wood so as to allow for the maximum drying time for all pieces Don t Burn Wood Scraps Garbage Paper Wax Logs Coal Etc Wood scraps from construction are typically chemically treated making them difficult to burn and dangerous due to emitting chemicals The same holds true for garbage solvents driftwood containing salt cardboard and colored paper Coal and wax impregnated logs burn especially hot creating a possible safety hazard In addition all the aforementioned items may create excessive creosote MAINTAINING YOUR APPLIANCE pace 23 MAINTENANCE SCHEDULE Your appliance requires periodic maintenance to work correctly The steps involved with maintenance are usually quick and easy Look through this maintenance schedule and plan accordingly WARNING Failure to properly maintain and inspect your appliance may reduce the performance and life of the appliance void your warranty and create a fire hazard PERIODIC MAINTENANCE every week when appliance is in use e Remove ash from the firebox if necessary e Clean t
18. INC to your regional distributor or dealership 4 Check with your dealer in advance for any costs to you when arranging a warranty call Dealers may require you to pay a service or trip charges for any warranty work This charge can vary from store to store Gants pace32 PRODUCT LISTING INFORMATION The data on the label below matches the data on the label attached to the back of your stove Warnock Hersey DO NOT REMOVE THIS LABEL usag LISTED SOLID FUEL BURNING APPLIANCE SUITABLE FOR USE IN RESIDENTIAL ALCOVE REPORT 6014 MAY 94 AND MOBILE HOME INSTALLATIONS S MODEL TESTED TO RELEVANT PORTIONS OF SERIAL LIBERTY 520 NT UL 1482 737 AND 907 NUMBER PREVENT HOUSE FIRES Install and use only in accordance with the Lopi Liberty 520 NT owner s manual Contact your toca building or fire officials about restrictions and installation inspection in your area Refer to local building codes and the chimney manufacturer s instructions for precautions required for passing a chimney through a combustible wall or ceil ing Do not run a chimney connector through a combustible wall or ceiling Do not connect this unit to a chimney flue serv ing another appliance Clearances may be reduced by methods specified in NFPA 211 listed wail shietds pipe shields or other means approved by local building or fire officials FREESTANDING INSTALLATION STANDARD RESIDENTIAL FREESTANDING INSTALLATIONS REQUIRE 6 diameter minimum 24 M
19. NDARY AIR TUBE COLLARS Must have the two push pins inserted into them This keeps the secondary air tubes aligned MAINTAINING YOUR APPLIANCE CONTINUED pace 27 Firebrick Removal and Replacement Instructions With the appliance cool remove all ash from the firebox Only the firebrick that is damaged must be replaced If the damaged firebrick is on the floor it can be replaced by simply removing the firebrick in front of it NOTE Do not pry firebrick to remove this will chip or crack the firebrick If a firebrick on the wall of the firebox needs replacement the floor firebrick near it will need to be removed first The wall firebrick is held upright by a clip on the walls of the firebox To remove pivot it out from the bottom See the illustration on the following page WALL FIREBRICKS First remove the firebricks on the floor in front of the firebrick needing replacement Then pivot it out from the bottom to CLIPS clear the clip that holds it in Hold the wall firebrick in place place FLOOR FIREBRICKS Remove the firebricks in front of the firebrick needing replacement FIREBRICK SIZES All firebrick is 1 1 4 x 4 1 2 x 9 except those labeled Firebrick labeled A are 1 1 4 x 4 1 2 x 6 3 8 Firebrick labeled B are 11 4 x 4 1 2 x 8 1 4 Baffle Removal and Replacement Instructions The view below details the baffle components Instru
20. SG black or 25 MSG blued steel connector with listed type HT factory built chimney suitable for use with solid fuels or masonry chimney Pedestal or legs are required ALCOVE INSTALLATIONS REQUIRE One of the listed doublewall connectors shown below Pedestal or legs are required Maximum alcove depth 48 minimum alcove height 84 MOBILE HOME AND REDUCED CLEARANCE INSTALLATIONS REQUIRE One of the listed doublewall connectors shown below tn addition mobile home instatlations require outside air use the optional pedestal or outside air boot Pedestal or legs are required e DURAVENT model DVL with DURA PLUS chimney METALFAB model DW connecter with TG chimney AMERI TEC model DCC with metet HS chimney Standard Masonry Chimney with any one of the above listed connectors e SECURITY model DP with SECURITY model ASHT or 2100 chimney CLEARANCES AND STANDARD RESIDENTIAL MOBILE HOME ALCOVE AND INSTALLATION SINGLE VALL REDUCED CLEARANCE INSTALLATIONS CONNECTOR REQUIRES DOUBLE WALL CONNECTOR SIDEWALL TO UNIT BACKWALL TO UNIT CORNER TO UNIT SIDEWALL TO CONNECTOR BACKWALL TO CONNECTOR CORNERWALL TO CONNECTOR For use with solid wood fuels only cord wood Operate with MINIMUM CLEARANCES TO COMBUSTIBLES FLOOR PROTECTOR feed door closed open to feed fire only Do not use a grate or elevate fire build fire directly on the hearth BACKWALL ADJACENT WALL TIVA INIJYrAY Manufactured by eS Travis Industries Inc
21. aint iiiter a e daye 26 Blower Cleaning e cccescesseeeeneeeeeeeeaeeeneeteaeeseeetenees 26 Firebrick And Baffle Inspection And Cleaning 26 Firebrick Removal and Replacement Inst 27 Baffle Removal and Replacement Inst 27 Replacement Parts LiSt eee eeseeeesseeeeseeeeeeneeeeees 29 Troubleshooting Troubleshooting Table eseeeeseeeeesneeessneereneeees 30 Warranty Wartanty si c a heal ute i i hee 31 Listing Information Listing Information eeseeeseeeeeseeeeesneeeeeneeeeeneeeeee 32 Optional Equipment Stove Legs Installation ececeeeeeeeeeeeeeeseeeeneeeees 33 Pedestal Installation ccccccccccceeseeeeseesesssesssessnaees 33 Using Outside Air with the Pedestal 34 Outside Air Boot Installation cccccccsseceesseseees 34 Rear Blower Installation cccccccccccsessssssesssnseeees 35 Index WAGs 222 2S aodi ta AEETI TEET 36 FEATURES AND SPECIFICATIONS paces Installation Options Features Freestanding EPA Phase II Approved 3 1 Cubic Foot Firebox Volume Single Push Pull Operating Control Freestanding in an Alcove Freestanding in a Mobile Home Accepts Logs Up to 24 Long Freestanding Hearth Stove Long Burn Time Up to 12 Hours 5 16 amp 3 16 Steel Plate Construction Heavy Duty Refractory Firebrick Optional High Tech Blower Heating Specifications Approximate Maximum Heating
22. ar and flashing are Chimney Sections required some require NOTE ae i H a radiation shield Exterior Minimum Air Space to n chimneys are Combustibles See oo Minimum 15 subject to Chimney Manufacturer s Wall Bands lt 1 Maximum 33 greater Instructions usually 2 and Supports __ You should have at moisture and least 8 of vertical chimney for every 1 of horizontal run due to the creosote Min 18 clearance gt gt accumulation to ceiling Al Insulated Tee TUTMUUTUIUI IY lower SC temperatures Chimney Connector Follow the chimney An insulated Sections manufacturer s chase will Floor Protection instructions and reduce these See the clearances for wall accumulations section Floor penetrations A wall the proper Protection fear a ns thimble is required oe 1 Requirements lt Stove Clearances the chimney for more See the section Stove must be details Placement Requirements Optional maintained for more details y insulated chase HEARTH ra fi STOVE NOTE The entire fireplace Cap prevents water NIVVE including chimney must be clean from entering POSITIVE and not cracked or damaged CONNECTION Any damage must be repaired prior to installation of the insert NOTE Chimney must be at least 15 tall Flue Liner Most factor
23. art to flatten The glass is held in place with the glass retainer and ten screws ross Section Door Frame The door gasket is 7 8 white rope gasketing and is held in place with gasket cement gt a Make sure Use a 5 16 nutdriver for there is a the glass retainer re E small space around the edge of the glass Glass Retainer 3 4 Black Channel Tape LUBRICATE THE DOOR HINGE Periodically lubricate the door hinges with a high temperature lubricant such as Permatex Industrial Anti Seize Lubricating the door involves removing the door by opening it and lifting it off the hinges and placing lubricant on the hinge pins pace2s MAINTAINING YOUR APPLIANCE CONTINUED TOUCH UP PAINT Included with the owner s pack of this appliance is a can of Stove Brite paint To touch up nicks or dulled paint apply the paint while the appliance is cool Use 120 grit sandpaper clean with water and dry with a piece of cloth if the surface requires smoothing Wait at least one hour before starting the appliance The touched up area will appear darker than the surrounding paint until it cures from heat Curing will give off some fumes while curing open windows to ventilate the fumes Touch Up Paint BLOWER CLEANING The optional blowers for this appliance will gather dust as they circulate air Before cleaning remove the blower from the appliance instructions are included i
24. boot to the bottom of the stove with two of the included sheet metal screws 5 Right the stove and position it in its final position Mark the location where the air boot contacts the floor Attach fiberglass tape to the bottom of the air boot so it covers all four edges of the air boot and telescope the air boot down until it makes contact with the floor Press against the air boot so it seals against the floor 6 The two holes on the sides of the air boot are used to hold for a screw that keeps the two telescoping segments of the air boot from moving Use the included 9 64 drill bit to drill a hole through the holes and into the top segment of the air boot Then screw the two remaining sheet metal screws into these holes Use touch up paint to remove scratches from the outside air boot 7 The outside air boot includes several cover plates Use the cover plate that is 6 1 2 wide The rest may be discarded Remove the two screws that hold the piece that fits over the air control rod in place see the illustration on the previous page under 3 Slide the air control plate in place underneath the air control rod Replace the piece removed from the cover plate The cover plate should form an air tight seal against the air control portion of the stove REAR BLOWER INSTALLATION Part 99000138 The rear blower increases the natural convection of the stove by pushing air through the convection chamber of the stove and causing the heated air to exit
25. coals are enough to start a new some there fire if kindling is placed on top Appliance Does Not Draft is low Your installer or dealer can give you more information Burn Fast On on draft The most common causes of low draft are a High short offset or small chimney an external down draft due to wind an extremely air tight home with exhaust fans or a thermal down draft due to appliance placement Wood is wet Wet wood will give off much less heat than dry seasoned wood see A Word about Wood on page 21 Appliance is cool New high tech appliances have a lag time between adjusting the air control and the fire speeding up Blower Does Not Appliance is not hot enough yet Appliance must be up to temperature for the blower to Turn On turn on if it is turned to AUTO see Blower Operation on page 20 Blower is not plugged in or Check the outlet that the blower is plugged into with a circuit is off lamp to see if it has power Smoke Is Dirty When reloading or starting The fire is evaporating the water from the wood giving From Chimney smoke is higher than normal off more visible smoke Wood is wet Wet wood will give off much more smoke than dry seasoned wood see A Word about Wood on page 21 WARRANTY Paces To register your TRAVIS INDUSTRIES INC 7 Year Warranty complete the enclosed warranty card and mail it within ten 10 days of the appliance purchase date to TRAVIS INDUSTRIES INC 10850 117th Place N E Kirkland Was
26. conds to establish a strong draft 3 Open the door one inch and let air enter the appliance for a few seconds 4 Carefully place the new wood on top of the existing fire Close the door and shut the bypass by pushing it all the way in Let the fire burn on high for at least 20 minutes before turning it down this will reduce creosote build up BYPASS CONTROL AIR CONTROL Open the door 1 and let air enter the appliance for a few seconds How to Adjust the Heat Output Precisely One complaint from wood burning appliance owners is controlling the heat output to obtain a consistent room temperature The reason for this is the inherent lag time between adjusting the air control and the change in heat output Simply put if you turn a hot appliance down now it will continue to put off high amounts of heat for an additional 15 minutes To obtain consistent room temperature think ahead When the room is starting to warm and is almost up to the right temperature turn the appliance down If you utilize an optional blower turn it on and off to increase or decrease room temperature If you find the appliance must be turned down often burn smaller more intense fires instead Although this means more reloadings it will reduce creosote build up and give a more consistent heat output OPERATING YOUR APPLIANCE CONTINUED Pace 19 How to Obtain an Overnight Burn An overnight burn of
27. ction Alcove Installation Requirements e Must maintain the following clearances to combustibles drywall furniture etc Minimum Clearance Singlewall Reduced See the illustration below Connector Clearance A Sidewall to stove 16 16 B Backwall to stove 15 10 C Cornerwall to stove 9 1 2 7 1 2 D Connector to sidewall 28 27 1 2 E Connector to backwall 18 1 4 12 3 4 F Connector to cornerwall 21 18 1 2 Rear heat Measure all clearances from the nearest edge of the stove top Reduced clearance installations require one of the chimney systems listed below e DURAVENT model DVL with DURA PLUS chimney e AMERI TEC model DCC with model HS chimney e SECURITY model DP with SECURITY model ASHT or 2100 chimney e Standard Masonry Chimney with any one of the above listed connectors e Metalfab model DW connector with TG chimney NOTE Reduced clearance connectors can not connect directly to the flue collar Make sure to order an appliance adapter for the brand of connector being used FLOOR PROTECTION REQUIREMENTS 6 Minimum from rear of stove not stove top or heat shield e Must be non combustible and at least 018 thick 26 gauge _ Heat Shield e Must extend 6 to the side and rear of Stove Top the appliance PP 6 Minimum e Must extend 16 from the front eat cee stove measure from the faceplate not stoventop e Minimum 42 3 8 deep by 39 1 2 N Floor Protection id 16 Minimum
28. ctions for removal are on the following page Bypass Rod threaded in two locations for easy removal Bypass Handle Baffle Bypass Firebrick Center Baffle Support Forward Baffle Support Bypass Support note its orientation and how it rests on the rear baffle firebrick Baffle supports rest on these tabs pace28 MAINTAINING YOUR APPLIANCE CONTINUED Baffle Removal and Replacement Instructions continued All of the baffle components are removable to facilitate easy cleaning and repairs Make sure the appliance is cool before removing any of the components See the instructions on the following page for removing the secondary air tubes REMOVING BAFFLE COMPONENTS 1 Lift up on the front portion of SIDE VIEW the front three firebricks Front Firebrick 2 Lift the front baffle support and rotate it forward until it can be removed Front Tab Baffle Welded to Support Firebox 3 Slide the center front firebrick forward and out the door opening Then slide the side front firebricks towards the middle then out in the same manner 4 Slide the center baffle support forward and out of the firebox 5 Slide the rear firebrick forward and out of the firebox NOTE When the center rear firebrick are slid forward the baffle support will come to rest on the rear secondary air tube and r
29. dustries will not be responsible for inadequate performance caused by environmental conditions such as nearby trees buildings roof tops wind hills or mountains or negative pressure or other influences from mechanical systems such as furnaces fans clothes dryers etc 6 This Warranty is void if a The unit has been operated in atmospheres contaminated by chlorine fluorine or other damaging chemicals b The unit is subject to submersion in water or prolonged periods of dampness or condensation G Any damage to the unit combustion chamber heat exchanger or other components due to water or weather damage which is the result of but not limited to improper chimney venting installation Ti Exclusions to this 7 Year Warranty include injury loss of use damage failure to function due to accident negligence misuse improper installation alteration or adjustment of the manufacturer s settings of components lack of proper and regular maintenance damage incurred while the appliance is in transit alteration or act of God 8 This 7 Year warranty excludes damage caused by normal wear and tear such as paint discoloration or chipping worn or torn gasketing chipped or cracked firebrick etc Also excluded is damage to the unit caused by abuse improper installation modification of the unit or the use of fuel other than that for which the unit is configured use cord wood only 9 Damage to brass surfaces caused by fingerprints scratches melted items
30. e door face down and check the door gasket see the illustration below If the door gasket requires replacement see the section Replacing the Door Gasket on the following page Check the glass and glass gasket If the glass or gasket require replacement see the section Replacing the Glass or Glass Gasket on the following page The door gasket should be unbroken have enough bulge to contact Check the the face of the unit and glass for any be firmly attached to the cracking door frame The glass gasket should form an airtight seal between the glass Door Cam and the door frame Adjusting the Door Cam If the door cam does not pull the door against the face of the appliance the door cam will need to be tightened see the illustration below for details If the door handle does not turn down all the way it is too tight and will need to be loosened see the illustration below for details Before adjusting remove the door by opening the door and lifting it off the hinges Side View of Door Handle Exploded View Door Cam ee ae Door Handle i EEE i E Door Cam Adjustment a To tighten remove Washers a washer from the inside of the door frame To loosen Use a 9 16 place an additional Door Frame socket wrench to washers onthe remove this nut inside of the door frame or loosen the nut 1 2 turn
31. ear air channel 6 Slide the bypass support to the left and the bypass damper to the right so the bypass damper seperates from the support Lower the bypass damper so bypass rod disengages from the bypass damper from the top 7 Remove both components by sliding them between the front two secondary air tubes The bypass support will need to be rotated 90 for removal REPLACEMENT INSTRUCTIONS A Place the bypass support above the secondary air tubes in the rear left of the firebox B Position the bypass damper so the bypass rod inserts into the two tubes on the bypass damper make sure to have correct orientation Then slide the bypass support under the bypass damper until both are centerd in the firebox C Follow the instructions above in reverse order starting with step number 5 MAINTAINING YOUR APPLIANCE CONTINUED pace 29 Baffle Removal and Replacement Instructions Continued REMOVING THE SECONDARY AIR TUBES Pry out both pins on the secondary Follow the directions to the right air tube sleeve use a screwdriver to remove any of the three seconary air tubes Secondary Air 7 Tube Sleeve Slide the secondary air tube sleeve to the left NOTE When replacing make sure the two holes on the secondary air tube sleeve line up with the hole on the secondary air tube and the hole on the air tube stub welded to the side air chan
32. edges of pedestal to seal off any air from entering underneath the pedestal 3 Attach the cover plate to the front of the stove Remove the two screws that hold the piece that fits over the air control rod in place Slide the air control plate in place underneath the air control rod Replace the piece removed from the cover plate The cover plate should form an air tight seal against the air control portion of the stove see the illustration below S Remove the two screws on the cover plate to remove the piece that fits over the air control rod Then replace the TE piece when the cover plate is in place i Air Control Rod The cover plate has a clip which s j P attaches it underneath the air control OUTSIDE AIR BOOT INSTALLATION PART 99200134 The outside air boot includes all of the items necessary to route outside air to the stove for combustion when a stove is installed on legs Before installing check the section Outside Air Requirements on page 9 for installation concerns The directions below outline the steps for installing outside air boot 1 Before installing the stove determine the location of the outside air hole that penetrates through the floor protection and floor The illustrations below detail the size of the outside air boot and its location in relation to the faceplate of the stove The hole may be cut anywhere underneath the outside air boot as long as it is not within 1 of t
33. eeeeeeeeteeseeeeeaee 6 Stove Installation Considerations ccceeee 6 Stove Installation Diagrams starting on page 12 SlOVE LOGS deiere nsan a a ail Meat REE 33 Stove Placement Requirements sessen 7 Table of Content 0 00 eeeeeseseeeeeseeesaeeeeeeseeteeeeeeeeeaes 4 Troubleshooting Table eeseeeeeseeeseneeeeeeneeeenneeees 30 Tube Replacement Secondary air tube ee 29 Warranty erasia ats hit wae i 31 Weight DiMeNSiONS seeeeeseeeeeeeeeeeneeeeeeeeeenaeeees 5 Wood Quality tri seanna en ea tae 21 Wood Storage cc esscsecteecsetsisedessescenederssateeseneneieescectteceass 21 Wood Types ij ac0h non ake tla 22
34. etc to allow air to move around the non combustible walls and ceiling All other alcoves are considered combustible The clearances below must be met Minimum Clearance See the illustration below Combustible Alcove Non Combustible Alcove Sidewall to stove Backwall to stove Connector to sidewall Connector to backwall Maximum depth of alcove Minimum width of alcove Minimum height of alcove CIrQOmMvVwayS Non combustible alcove construction on walls and ceiling see the explanation above Ventilated 27 1 2 12 3 4 48 62 84 17 1 2 4 3 4 48 42 6 above stove top alr space 3 42 thick non combustible material Combustible materials Non combustible reinforcer STOVE INSTALLATION CONT pace 11 MOBILE HOME REQUIREMENTS The Liberty is approved for installation into a mobile home if the requirements listed below are met in addition to the normal requirements Outside air must be installed see Outside Air Requirements on page 9 The appliance must be bolted to the floor The optional pedestal provides the equipment needed to do this see Pedestal Installation on page 33 The appliance must be grounded to the chassis of the mobile home some states do not require this check with local building officials The appliance must not be located in the bedroom of a mobile home some states do not require this check with loca
35. he outside perimeter of the outside air boot is at least 16 square inches in area and does not interfere with structural members of the home Cut the hole when the correct location is determined 2 Install the legs see instructions above Pry out the outside air knock out Itis 7 wide 2 deep and 6 11 16 back from the front of the stove See the illustration below 3 Align the air boot over the knock out and mark the locations where the two holes located on the top side of the air boot line up on the bottom of the stove Use the included 9 64 drill bit to drill holes into the bottom of the stove where the marks were placed you may need to tilt the stove or place it on its side Drill only enough to penetrate the first layer of metal The air boot Holes for its Oxer attaching yor Ss CS zS Attach fiberglass this hole the outside Ff 00 to entire air boot to surface on all the stove four edges li f pee Top _ o lt t Hole for oot Y Segment Attaching P ee Ly Bottom lt et Segment to Bottom Top Segment See the instructions for Segment VF 1 8 exact location and size tH OPTIONAL EQUIPMENT CONTINUED pace 35 4 Attach the fiberglass tape to all four top edges of the air boot There is a seam in the bottom segment of the air boot Position the air boot over the knock out so this seam is facing the rear Attach the air
36. he viewing glass if necessary e Clean the brass if necessary e Check for creosote buildup in the chimney and connector BI MONTHLY MAINTENANCE every two months during the heating season e Door and glass inspection e Lubricate the door hinge YEARLY MAINTENANCE before every heating season e Touch up paint e Blower cleaning e Firebrick and baffle inspection and cleaning REMOVE ASH FROM THE FIREBOX IF NECESSARY At least once a week while the appliance is in use check the level of ash on the floor of the firebox If 1 or more of ash has accumulated let the appliance cool and place the excess ash into an airtight container away from any structure After the ash is fully extinguished it may be disposed A 1 2 to 1 bed of ash is desirable for it allows the appliance to burn at a slightly lower speed WARNING Ashes removed from the appliance must be stored in an airtight container away from any structure until fully extinguished before disposing CLEAN THE VIEWING GLASS IF NECESSARY This appliance has an airwash to keep the glass clean However burning un seasoned wood or burning on lower burn rates leads to dirtier glass especially on the sides Clean the glass by following the directions below For especially dirty glass use fine steel wool to remove build up Apply glass Then take a piece of newspaper cleaner to the or paper towel dip it in cool wee ade Fr SS ashes and wipe the glass glass when i is cool
37. hington 98033 TRAVIS INDUSTRIES INC warrants this appliance appliance is defined as the equipment manufactured by Travis Industries Inc to be defect free in material and workmanship to the original purchaser from the date of purchase as follows Years 1 amp 2 COVERAGE PARTS amp LABOR Firebox Assembly Ceramic Glass RE INSTALLATION ALLOWANCE Firebox Baffle Supports Air Tubes Air Channels Convection Glass breakage from thermal shock In cases where heater must be removed from Chamber Firebrick home for repairs a partial cost of re installation is Door Assembly Breakage from thermal shock covered pre authorization required Solid Brass or Cast Door Latch Assembly Glass Retainers Accessories ONE WAY FREIGHT ALLOWANCE i y PIE ee Fy One Way Freight Allowance On Pre Authorized Ai r Control Assembl Legs Pedestal Panels Blower Repair Done At Factory Is Covered Slider Plate Pressure Plate Exclusions Paint Gasketing Years 3 Through 5 COVERAGE PARTS amp LABOR Firebox Assembly Door Assembly ONE WAY FREIGHT ALLOWANCE Firebox Baffle Supports Air Tubes Air Channels Convection Chamber Solid Brass or Cast Door Latch ONE Way Freight Allowance On Pre Authorized Air Control Assembly Assembly Glass Retainers Repair Done At Factory Is Covered Slider Plate Pressure Plate Exclusions Paint Gasketing Accessories Legs Pedestal Panels Blower Glass Firebrick Re Installation Allowance Years 6 a
38. hort offset or small chimney an external down draft due to wind an extremely air tight home with exhaust fans or a thermal down draft due to appliance placement Kindling Does Not Cold air block in chimney A cold air block keeps the appliance from establishing a Start draft First ignite a piece of newspaper in the appliance before starting the kindling Kindling is wet or too large to Kindling must ignite quickly to be effective Wet or light large kindling will make starting very difficult Bypass was closed Pull the bypass all the way out before starting the stove see Bypass Control on page 17 Appliance Does Not Wood is wet unseasoned or Wet wood will give off much less heat than dry seasoned Put Off Much green wood see A Word about Wood on page 21 Heat Appliance requires time to The appliance will not give off heat until it has been warm up burning on high for at least one half hour see Learning to Burn your Appliance on page 17 Bypass was open The bypass should be closed once the fire is established to increase the stove s efficiency see Bypass Control on page 17 Appliance Does Not Wood is fast burning Lighter faster burning woods e g alder pine are less Burn Overnight suited for overnight burns see A Word about Wood on page 21 Wood is in small pieces Wood should be large to facilitate a slower burn see How to Achieve an Overnight Burn on page 19 Check for coals there may be Even a small amount of
39. je z 4 Leveling bolts are attached to the leg Do not have any weight on the bolts while adjusting them the RL rubber tips may tear To level the stove lift the stove up and unscrew each leveling bolt the appropriate amount The rubber tips of the leveling bolts will tear if they are adjusted while weight is applied to them PEDESTAL INSTALLATION PART 99200101 NOTE If installing outside air with the pedestal first follow the directions titled Using Outside Air with the Pedestal on the following page Place the pedestal in place and lift the stove on top of it Line up the threaded bolt holes in the bottom of the stove with the two holes in the tabs that stick out of the side of the pedestal see the illustration below Using a 9 16 socket wrench fasten the pedestal to the stove with the supplied bolts and washers If installing in a mobile home the pedestal will need to be attached to the floor Insert the two included lag bolts through the pedestal base and screw them into the floor with a 1 2 socket wrench Optional Air Attachment Bolts and Washers use a 9 16 socket wrench to attach the pedestal to the stove e lt gt Intake Port If installing in a mobile home insert the lag bolts through these holes and screw them into the floor with a 1 2 socket wrench 9 L es 20 When attached the faceplate of the stove is 4 3 4 in fr
40. l building officials Chimney connector and chimney must be one of the following types e DURAVENT model DVL with DURA PLUS chimney e AMERI TEC model DCC with model HS chimney e SECURITY model DP with SECURITY model ASHT or 2100 chimney e Standard Masonry Chimney with any one of the above listed connectors e Metalfab model DW connector with TG chimney NOTE Reduced clearance connectors can not connect directly to the flue collar Make sure to order an appliance adapter for the brand of connector being used Stove placement must maintain the following clearances to combustibles drywall furniture etc Minimum Clearance See the illustration below A Sidewall to stove 16 B Backwall to stove 10 C Cornerwall to stove 7 1 2 D Connector to sidewall 27 1 2 E Connector to backwall 12 3 4 F Connector to cornerwall 18 1 2 Rear heat F shield a Measure all clearances from e nearest edge of the stove top Pacei12 STOVE INSTALLATION CONT STANDARD CEILING WITH A FACTORY BUILT CHIMNEY CATHEDRAL CEILING WITH A FACTORY BUILT CHIMNEY Chimney Cap See the section Chimney Termination Requirements for more details Chimney Sections Insulation Follow the chimney manufacturer s instructions and clearances for floor penetrations A chimney support is required an attic insulation shield is required where insulation is present Chimney Connector Sectio
41. ls a gt Combustible Mantle z See the section Stove Placement Requirements for minimum clearances required _ _ Flue Liner Follow the chimney manufacturer s instructions and clearances for wall penetrations A wall radiation shield thimble is required Airtight Insulated Clean Out __ Either close off and seal the damper install a block off plate or install a damper adapter STOVE INSTALLATION CONT pace 15 BLOCK OFF PLATE INSTALLATION Whenever this appliance is installed as a direct connection a block off plate or other non combustible seal off device e g damper adapter will need to be installed This device is used to seal the chimney insuring no smoke enters the home and providing the chimney system with a seal to provide greater draft The directions below detail the steps for construction and installation of a block off plate 1 Determine a location for the block off plate at the top of the firebox below the damper area make it high enough to allow installation of the connection pipe The location should be level and in an area where it can be mounted easily Measure the width at the rear A and front B of the firebox at the height where the block off plate will be installed see the illustration below Then measure the depth
42. mney must be clean and not cracked or damaged Any damage must be repaired prior to Combustible Mantle a A installation of the insert Chimney must be at least 15 tall and no greater than 33 tall Entire fireplace including chimney must meet local building requirements Min 18 Floor Protection See the section Floor Protection Requirements for more details S Block off plate or damper adapter N _ Flue Liner Stainless steel chimney connector must Extend 1 past the block off plate or to the flue liner e Airtight Insulated N Clean Out Remove damper or wire it open See the section Stove Placement Requirements for minimum clearances required NOTE The chimney must have a clay tile liner If it does not the installation must use a positive connection full reline Entire fireplace Min 18 clearance to ceiling including chimney must be clean and not cracked 2 or damaged Any damage must be repaired prior to installation of the insert Chimney must be at least 15 tall and no greater than 33 tall Entire fireplace including chimney must meet local building requirements Chimney connector sections fiim Floor Protection See the section Floor Protection Requirements for more detai
43. mp 7 COVERAGE PARTS ONLY Firebox Assembly Door Assembly Air Control Assembly Firebox Baffle Supports Air Tubes Air Channels Solid Brass or Cast Door Latch Assembly Glass Retainers Slider Plate Pressure Plate Convection Chamber Exclusions Paint Gasketing Accessories Legs Pedestal Panels Blower Glass Firebrick Re Installation Allowance One Way Freight Allowance Labor CONDITIONS amp EXCLUSIONS 1 This new appliance must be installed by a qualified installer It must be installed operated and maintained at all times in accordance with the instructions in the Owner s Manual Any alteration willful abuse accident neglect or misuse of the product shall nullify this warranty 2 This warranty is nontransferable and is made to the ORIGINAL purchaser provided that the purchase was made through an authorized Travis dealer 3 Discoloration and some minor expansion contraction or movement of certain parts and resulting noise is normal and not a defect and therefore not covered under warranty Over firing operation where the steel may glow red of this appliance can cause serious damage and will nullify this warranty 4 The warranty as outlined within this document does not apply to the chimney components or other Non Travis accessories used in conjunction with the installation of this product If in doubt as to the extent of this warranty contact your authorized Travis retailer before installation 5 Travis In
44. n Optional Equipment section in the back of this manual Remove all dust and debris from the blower grill and around the interior of the blower FIREBRICK AND BAFFLE INSPECTION AND CLEANING With the appliance cool remove all ash from the firebox and scrape away any scale that may have built up on the surface of the firebrick with a wire brush or scraper Any of the firebrick on the floor or walls of the firebrick that is cracked must be replaced see the section Firebrick Removal and Replacement Instructions Next inspect the baffle components The illustration below details the areas that must be inspected If any of the components need to be replaced see the section Baffle Removal and Replacement Instructions BYPASS ASSEMBLY Entire assembly must be properly aligned and correctly oriented BAFFLE FIREBRICKS Must not be cracked or have gaps between them Cracked bricks must be replaced Gaps are eliminated by pushing the bricks closer together SECONDARY AIR TUBES Must be intact without any cracks Scaling and a slight amount of bending is normal for this component A N BAFFLE SUPPORTS Must be snug against the baffle SS firebricks and resting on the seconary air collars FLOOR amp WALL FIREBRICKS Must not be cracked or severely chipped damaged bricks must be replaced Remove any scaling or buildup with a scraper or wire brush SECO
45. nce must be placed so crawl space or use an air duct it does not become blocked by snow NOTE Ifthe duct is less than 5 feet long the cross section may be a min 12 square inches HINT When using outside air find a location where the chimney and outside air inlet avoid the structural members i e floor joists and roof beams of the home Pacei0 STOVE INSTALLATION CONT ALCOVE INSTALLATION REQUIREMENTS Whenever the stove is placed in a location where the ceiling height is less than 7 tall it is considered an alcove installation Because of the reduced height the special installation requirements listed below must be met e Chimney connector and chimney must be one of the following types DURAVENT model DVL with DURA PLUS chimney e SECURITY model DP with SECURITY model ASHT or S2100 chimney e Metalfab model DW connector with TG chimney e AMERI TEC model DCC with model HS chimney Standard Masonry Chimney with any one of the above listed connectors NOTE Reduced clearance connectors can not connect directly to the flue collar Make sure to order an appliance adapter for the brand of connector being used e Alcoves are classified as combustible or non combustible Non combustible alcoves must have walls and a ceiling that are 3 1 2 thick of a non combustible material brick stone or concrete This non combustible material must be spaced and ventilated at least 1 off of all combustible materials walls ceiling
46. nel Side Air Channel Welded to side of Firebox Air Tube Stub welded to the Slide the secondary air tube to the right d side air channel until it disengages from the left side m3 REPLACEMENT PARTS LIST PART DESCRIPTION Black 3 4 x 1 8 fiberglass channel tape 60 long 22 7 8 long with 3 16 holes every 3 4 includes two pins 23 5 8 long 1 1 2 angle iron welded to 21 1 8 long 1 deflector at 45 angle 23 5 8 long 1 1 2 angle iron welded to 23 5 8 long 1 strip to form a t 9 by 9 square 5 16 thick with two 7 1 4 x 1 guides top amp bottom stop Air Control Slider Steel plate with air control rod Air Control Floating Plate with Springs 8 springs and the floating plate used to guide air control slider Bypass Pull Tool Tool used to adjust bypass PaGE30 TROUBLESHOOTING Problem Possible Cause Smoke Spills From Door was opened before the air Push the air control all the way in a few seconds before Door When control was pushed in opening the door Loading Door was opened before the Pull the bypass all the way out before opening the door bypass was pulled out see Bypass Control on page 17 Door was opened too quick Door should be opened a crack to allow air to enter before opening all the way see How to Reload your Appliance on page 18 Draft is not adequate Your installer or dealer can give you more information on draft The most common causes of low draft are a s
47. netration Page 12 e Provides best draft Cathedral Ceiling with a Factory Built Chimney Cathedral style chimney support required Page 12 e Provides best draft Exterior Factory Built Chimney e Uses two elbows to route chimney outside Page 13 e Exterior chimney is hidden from the room e For every 1 of horizontal run you should have 8 of vertical chimney e Elbows reduce draft e Optional exterior chase reduces cold air blockage Hearth Stove Positive Connection e Utilizes existing masonry chimney Page 13 Provides good draft due to full reline e Easier to clean than direct or horizontal hearth stove Hearth Stove Direct Connection e Utilizes existing masonry or chimney Page 14 e Requires construction of a block off plate Page 15 e Draft reduced due to elbows amp chimney cross section Hearth Stove Horizontal Connection e Utilizes existing masonry chimney Page 14 e Draft is good because of vertical section above stove STOVE INSTALLATION CONT pPace7 STOVE PLACEMENT REQUIREMENTS HINT REDUCING CLEARANCES Clearances may be reduced by methods specified in NFPA 211 listed wall shields pipe shields or other means approved by local building or fire officials e Stove must be placed so that no combustibles are within or can swing within e g drapes doors 36 of the front of the stove e Ifthe stove is placed in a location where the ceiling height is less than 7 it must follow the requirements in the se
48. new appliance e Get the appliance hot before turning it down e Use smaller pieces of wood during start up and high burns to increase temperature e Use larger pieces of wood for overnight or sustained burns e Stack the wood tightly together to establish a longer burn e Leave a bed of ashes 1 2 deep to allow for longer burns e Be considerate of neighbors amp the environment burn dry wood only e Burn small intense fires instead of large slow burning fires when possible e Learn your appliance s operating characteristics to obtain optimum performance NOTE A stove thermometer gives you a good indication of how hot your appliance is burning when placed directly on top of the appliance Low burn is approximately 300 degrees F medium burn 500 to 600 degrees F and high burn 700 to 800 degrees F pace20 OPERATING YOUR APPLIANCE CONTINUED BLOWER OPERATION The optional blower assists the convection chamber in distributing heat to your home The directions below detail operation Automatic Control The optional blower has a temperature sensing device to automatically enable the blower once the appliance reaches a hot temperature It also shuts the blower off once the appliance has cooled When to turn the blower on The blower should be left on the off position for the first 30 minutes of starting the appliance Blower controls The control knob is located on the control box attached to the cord leading from the blower It is ope
49. ng on the firebox but do not tighten so as to dislodge the thermodisk assembly 3 Route the two yellow wires from the blower box through the hole in the back of the blower box the wires must not exit out of the top Connect these wires to the two wires from the thermodisk assembly orientation does not matter 4 Place the blower box near the bottom rear of the stove and push any slack wire into the blower box so that when the blower box is attached the excess wire will not contact the stove Attach the blower box to the stove with the three screws included with the blower kit use a 3 8 nutdriver You may wish to pre thread the holes in the back of the stove prior to putting the blower box in place pace3s INDEX Adjusting the Heat OUtpUt eee eeeeeeeeeeeteteeeeeeeee 18 Air Control Settings eecceceeeeeseeeeeeeeeeeeeeeeeeeeneeeee 16 Air Tube Replacement Inst aeee 29 Alcove Installation Requirements 10 AshiRemOVal c ecatcarkcs Waid adit iy 23 Baffle Removal and Replacement Inst eee 27 Blower rear installation eseeesseeeseeeeesteeeeeaees 35 Blower Cleaning ccescceeseseeeeeseeteaeeeeeeteeeseeeeeaeeted 26 Blower Operation ccccceeeeeeeeeeeseeteeeeseeteeeteeeeeaeeeea 20 BTU Outputs w3 ic 2s ee aia vaste eens as 5 Burning your Appliance eeeeeeseeeeeneeeteneeeeesneeeeeaees 16 Cathedral Ceiling Installation eeeeeeeeeeeeeeeees 12 Chimney Inspection creosote
50. ns Floor Protection See the section Floor Protection Requirements for more details Follow the chimney manufacturer s instructions and clearances for roof penetrations A storm collar and flashing are required Some require a radiation shield Minimum Air Space to Combustibles See Chimney Manufacturer s Instructions usually 2 Minimum 15 Maximum 33 Stove Clearances See the section Stove Placement Requirements for more details Chimney Cap See the section Chimney Termination Requirements for more details Chimney Sections Minimum Air Space to Combustibles See Chimney Manufacturer s Instructions usually 2 Chimney Connector Sections Floor Protection See the section Floor Protection Requirements for more details Follow the chimney manufacturer s instructions and clearances for roof penetrations A storm collar flashing and cathedral style chimney support are required some require a radiation shield Minimum 15 Maximum 33 Stove Clearances See the section Stove Placement Requirements for more details STOVE INSTALLATION CONT pace 13 EXTERIOR ___ i oe _ Follow the chimney FACTORY Chimney Cap manufacturer s BUILT See the section Chimney L instructions and Termination Requirements clearances for roof CHIMNEY for more details penetrations A storm coll
51. of the location where the block off plate will be installed C Make a cardboard template of the measurements but add a 2 flange to each side This flange will be used to mount the block off plate to the inside of the firebox Bend the flanges downwards on the template and place it inside the fireplace If the template fits correctly in its planned location go to the next step If it does not make a new template with the appropriate corrections until it fits correctly With the template in place mark the location that is centered in the fireplace where the flue will exit This location approximates the center of the flue when the insert is in place a slight offset may occur based upon insert and block off plate placement Remove the template and cut a 6 1 4 diameter hole centered on this mark Make the block off plate of 24 gage or thicker steel to match the template Drill two holes in each flange for mounting the plate Mount the block off plate using the appropriate screws Masonry screws must be used for mounting a block off plate in a masonry fireplace Insulate the block off plate using high temperature fiberglass insulation Kaowool or equivalent and furnace cement allow the cement to dry for at least 24 hours before burning After placing the appliance and installing the pipe through the block off plate use high temperature fiberglass insulation and furnace cement to seal any cracks between the pipe and block off plate
52. ont of the front edge of the pedestal OUTSIDE AIR EQUIPMENT Insulation is Screen is used used to seal GF to prevent the side edges rodents from of the pedestal entering Staples are used to attach the screen to the floor to seal off room air e The cover plate is used pace34 OPTIONAL EQUIPMENT CONTINUED Using Outside Air with the Pedestal The pedestal kit includes all of the items necessary to route outside air to the stove from the floor Before installing check the section Outside Air Requirements on page 9 for installation concerns The directions below outline the steps for installing outside air with a pedestal 1 Before installing the stove or pedestal determine the location of the outside air hole that penetrates through the floor protection and floor The illustration on the previous page details the size of pedestal and its location in relation to the faceplate of the stove The hole may be cut anywhere underneath the pedestal as long as it is not within 2 of the outside perimeter of the pedestal is at least 16 square inches in area and does not interfere with structural members of the home Cut the hole when the correct location is determined Place the screen over the hole and secure it in place with the included staples It can be attached above or below the floor 2 Place the pedestal in place Tuck the insulation included with the pedestal underneath the side
53. or other external sources left on the brass surfaces from the use of abrasive cleaners is not covered in this warranty 0 TRAVIS INDUSTRIES INC is free of liability for any damages caused by the appliance as well as inconvenience expenses and materials Incidental or consequential damages are not covered by this warranty In some states the exclusion of incidental or consequential damage may not apply 1 This warranty does not cover any loss or damage incurred by the use or removal of any component or apparatus to or from the Travis appliance without the express written permission of TRAVIS INDUSTRIES INC and bearing a TRAVIS INDUSTRIES INC label of approval Any statement or representation of Travis products and their performance contained in Travis advertising packaging literature or printed material is not part of this 7 year warranty This warranty is automatically voided if the appliance s serial number has been removed or altered in any way If the appliance is used for commercial purposes it is excluded from this warranty 14 No dealer distributor or similar person has the authority to represent or warrant Travis products beyond the terms contained within this warranty TRAVIS INDUSTRIES INC assumes no liability for such warranties or representations Travis Industries will not cover the cost of the removal or re installation of hearths facing mantels venting or other components If for any reason any section of this warranty is decla
54. orm Collar Chimney gt Sections Floor Penetration ANGA o E Minimum Air Space to Equipment Attic Combustibles See Radiation Shield with Chimney Manufacturer s Chimney Support Instructions usually 2 F Standard residential installations with Reduceced a reduced clearance connector may use the Clearance clearance determined by the manufacturer Chimney i of the connector for the connector to wall Connector clearance or the clearance listed in this Sections E manual Mobile home installations must use the the reduced clearance connector Floor i clearances listed in this manual under Protection Additional Requirements for Mobile Home Installations Stove Clearance r b as outlined in this manual T DA m ma ian m m m E E Drafting This appliance relies upon natural draft to operate External forces such as wind Performance barometric pressure topography or factors of the home negative pressure from exhaust fans chimneys air infiltration etc may adversely affect draft Travis Industries can not be responsible for external forces leading to less than optimal performance STOVE INSTALLATION CONT paces CHIMNEY TERMINATION REQUIREMENTS e Must have an approved cap to prevent water from entering e Must not be located where it will become plugged by snow or other material e Must terminate at least 3 above
55. rated in the manner illustrated below OFF HIGH LOW Turn the knob Turn the knob Turn the knob all the way clockwise from all the way counter the off position clockwise to clockwise to until it clicks turn to low turn off How to Use the Blower to Regulate Heat Turn the blower on if the room needs heat and the appliance is up to temperature When the room has reached a high enough temperature turn the blower off to stop the heat transfer Used in conjunction with the air control a steady temperature can be achieved OPERATING YOUR APPLIANCE CONTINUED pace 21 A WORD ABOUT WOOD This appliance is designed to burn natural cord wood with high efficiencies and low emissions With properly dried wood you will fully realize the heating and clean burning potential of our high technology appliance With poor wood this high technology appliance will become much less efficient and produce more emissions Read on to find out more about the type of fuel you should use The Drier the Better The most common mistake made by wood burners is using wet green or Wet W un seasoned fuel Ask any experienced wood burner and he or she will tell you the importance of dry wood The reason is this wet green or un seasoned wood still has water in it When the wood burns it LEZ Dry Wood must use its heat energy to evaporate the water This robs your home of heat it also leads to greater smoke and creo
56. red invalid the balance of the warranty remains in effect and all other clauses shall remain in effect This 7 year warranty is the only warranty supplied by Travis Industries Inc the manufacturer of the appliance All other warranties whether express or implied are hereby expressly disclaimed and purchaser s recourse is expressly limited to the warranties set forth herein mm STON IF WARRANTY SERVICE IS NEEDED If you discover a problem that you believe is covered by this warranty you MUST REPORT it to your Travis dealer WITHIN 30 DAYS giving them proof of purchase the purchase date and the model name and serial number Travis Industries has the option of either repairing or replacing the defective component If your dealer is unable to repair your appliance s defect he may process a warranty claim through TRAVIS INDUSTRIES INC including the name of the dealership where you purchased the appliance a copy of your receipt showing the date of the appliance s purchase and the serial number on your appliance At that time you may be asked to ship your appliance freight charges prepaid to TRAVIS INDUSTRIES INC TRAVIS INDUSTRIES INC at its option will repair or replace free of charge your appliance if it is found to be defective in material or workmanship within the time frame stated within this 7 year warranty TRAVIS INDUSTRIES INC will return your appliance freight charges years 1 to 5 prepaid by TRAVIS INDUSTRIES
57. roduction amp Important Information eee 1 Leveling BONS tiei niie eani aa aaa eaan 33 Listing Information seeeeeeeeeeereerrnerirrerrerrrensrrreres 32 Location of Controls ecceecceeeeeeseeeeeeeeeeeeentesseeeeeeeee 16 Eo iLength orei eA 5 Maintenance Schedule seeseeeeeeeeeeeeeeeseeererensreeen 23 Mobile Home Requirements 11 Operating Your Appliance seeeeeeeeeeeeeeeeeee eeren 16 Optional Equipment starts on page seeeeeseeeeeeee 33 Outside Air Boot Installation 0 0eceeeeeeeeeeeeeeeees 34 Outside Air Requirement 0 cccceeeeseeeeeeeeeeeeeeee 9 Overnight Burning eeececeeeeeeeeeteeeeeeeeeeeteeeteeeeeaeetee 19 Paint Curing tciciet east elivivt besa Hao 16 Paint touch Up snd tuted aa e 26 Parts Listino ria oi a a aa aaao aAa ei aii 29 Pedestals csstanig ian anhii anlandoeatee hs 33 Positive Connection hearth stove 13 Rear Blower Installation ce eeseeseeeeneeeeeeeeeeenneeees 35 Reload Your Appliance s es 18 Replacement Parts List ec eeseeesseeeeseeeeeeneeeeenees 29 Safety Labeling eee ae ee 32 Safety Precautions ecceceseeseeseeeeeeeeeeneetseeeeeetseees 2 Secondary Air Tube Replacement Inst eeee 29 Secondary Air Tube warranty 5 yrs s es 31 Smell in Room see Paint Curing e e 16 Specifications aeeai neea a eia 5 Starting a Firen iaa a iaa E e EN EE Aha 17 Stove Installation cceecseeeeeeeeeeeeeteeeee
58. s must be strictly adhered to Do not use makeshift methods or compromise in the installation Inspect the chimney connector and chimney at least twice monthly and clean if necessary Creosote may build up and cause a house fire Do not connect this appliance to any chimney serving another appliance When installed in a mobile home this appliance must be bolted to the floor have outside air and not be installed in the bedroom Per H U D requirements Check with local building officials Gasoline or other flammable liquids must never be used to start the fire or Freshen Up the fire Do not store or use gasoline or other flammable liquids in the vicinity of this appliance Ashes must be disposed in a metal container with a tight lid and placed on a non combustible surface well away from the home or structure Keep furniture drapes curtains wood paper and other combustibles a minimum of 36 away from the appliance Contact your local building officials to obtain a permit and information on any installation restrictions or inspection requirements in your area Notify your insurance company of this appliance as well This appliance must be connected to a listed high temperature HT residential type chimney or an approved masonry chimney with a standard clay tile or stainless steel liner Do not place clothing or other flammable items on or near this appliance SAFETY PRE
59. sote due to lesser firebox temperatures Dry wood usually has cracks in the grain It will also be lighter and when two pieces are knocked together a crisp knock will be heard not a dull thud When burning green wet or unseasoned wood you may notice difficulty in lighting and water bubbling out of the grain when it becomes hot How to Dry and Store Wood ie I To More Smoke Aging is the only economical method for drying wood Follow the steps below to dry and store wood 1 Make sure the wood is split into quarters and is no longer than 18 long Hint if you cut trees in summer leave the leaves on for a week this will draw moisture from the wood to dry it quicker 2 Stack the wood in loose piles that are covered and off the ground this is to allow air to pass over each piece of wood promoting faster drying If no shelter is built place clear polyethylene plastic over the wood at an angle to allow moisture to run off Let dry for at least one year 3 Store the wood in a dry location preferably outside to prevent insects and dirt from entering the home When needed move small loads inside where the added heat will promote further drying Cut the wood to 18 or less lengths and chop into quarters before stacking Polyethylene Air Flow Winds P Stack the Keep the wood off the ground to increase air flow Air Flow Cover with 4 mil wood loosely to allow for air flow
60. t Information No other Lopi Liberty appliance has the same serial number as yours The serial number is Mail your Warranty Card Today and Save stamped onto the label on the back of the Your Bill of Sale appliance This serial number will be needed in case you require service of any type To receive full warranty coverage you will Model LOPI Libert need to show evidence of the date you purchased your appliance Do not mail your Bill of Sale to us Serial Number Purchase Date We suggest that you attach your Bill of Sale to this page so that you will have all the information you need in one place should the need for service or information occur Purchased From PAGE 2 SAFETY PRECAUTIONS The viewing door must be closed and latched during operation Never block free airflow through the air vents on this appliance This appliance is designed and approved for the burning of cord wood only Do not attempt to burn any other type of fuel other than cord wood in this appliance it will void all warranties and safety listings Do not touch the appliance while it is hot and educate all children of the danger of a high temperature appliance Young children should be supervised when they are in the same room as the appliance This appliance must be properly installed to prevent the possibility of a house fire The instruction
61. the roof and at least 2 above any portion of the roof within 10 Slanted Roofs VN Chimney must extend 2 i above any portion of the roof Chimney must within 10 of the chimney extend 3 above the roof mT Chimney must extend 2 above any portion of the roof Flat Roofs E E mm within 10 of the chimney Chimney must extend 3 above the roof OUTSIDE AIR REQUIREMENTS e Required for mobile homes amp in certain localities check with building officials e Must not be drawn from an enclosed space garage unventilated crawl space e Requires the optional pedestal or outside air boot with legs installation instructions are in the optional equipment section at the rear of this manual When using outside air find a location where the chimney and outside air hole do not interfere with structural members of the home A hole must be cut through the floor Outside protection and Air Boot floor and the rodent screen nailed in place here see the optional equipment instructions for exact sizes Pedestal with insulation directs air to the stove a Optional Air Duct must not be npa 4 mooo o longer than 15 and at least 16 square inches in cross section Air may be drawn from a ventilated f Outside air entra
62. tove near the top and is operated by pushing or pulling the control to the left or right When the control is completely pulled out the bypass allows the smoke to go directly up the flue creating more draft for starting the stove or for reloading When it is pushed in the smoke must go around the baffle which utilizes secondary combustion and makes the stove more efficient see the illustration below ru RreSets Bypass Pulled Out Used for Starting Bypass Pushed In and Re Loading Used for Normal Operation Utilizes Secondary Combustion LEARNING TO BURN YOUR APPLIANCE Using a wood burning appliance takes some getting used to Once you become accustomed to operating your appliance you will be able to start a hot fire quickly adjust the heat output precisely and obtain overnight burns easier Experienced wood burners may not need the information below but may be able to re affirm their skills by reading the following The better you understand your appliance the more rewarding you will find it How to Start a Hot Fire Quickly Your wood burning appliance acts much like an engine before it will work at its best it needs to reach a high temperature The most common mistake in starting a fire is to use too little kindling closing the bypass too soon or turning the air control down too early
63. urself your authorized dealer should review your plans for installation This stove is approved for connection to either a factory built chimney or existing masonry fireplace Depending upon your installation concerns a wide range of installation options are yours to provide the most desirable installation The sections that follow detail the requirements that must be met for a safe installation To further help installation the six most common types of installations are explained in the section Stove Installation Considerations Prior to installing your stove make a detailed plan with dimensions to double check them against all of the requirements listed PREPARATION FOR INSTALLATION e Check for damage to the exterior of the stove dents should be reported scratches can be fixed by applying touch up paint e Check the interior of the firebox damaged firebrick must be replaced displaced baffle parts must be aligned see Firebrick and Baffle Inspection and Cleaning on pages 26 28 HINT The stove can be lightened by removing the firebricks and baffle see Firebrick and Baffle Inspection and Cleaning on pages 26 28 STOVE INSTALLATION CONSIDERATIONS The table below details the six most common types of installations along with considerations Alternative methods of installation are available if they comply with local building codes Installation Type Standard Ceiling with a Factory Built Chimney Requires floor and roof pe
64. y and no greater than 33 tall built chimney Entire fireplace including The liner must be manufacturers chimney must meet local stainless steel connector make stainless building requirements or flexible vent Follow steel chimney the liner manufacturer s liners either i instructions for flexible or installation and support rigid This rovides a aa variety of Combustible Airtight Insulated Lety Mantle Clean Out installation options Make sure to follow Floor Protection Remove damper the See the section or wire it open manufacturer s Floor Protection instructions for Requirements Seethe Section installation for more details Stove Placement and support Requirements for minimum clearances required Pacei4 STOVE INSTALLATION CONT HEARTH STOVE DIRECT CONNECTION NOTE Direct connections require installation of an airtight block off plate or damper adapter see the section Block off Plate Installation on page 18 HEARTH STOVE HORIZONTAL CONNECTION NOTE This type of installation requires a wall radiation shield thimble Either close off and seal the damper install a block off plate or install a damper adapter see the section Block off Plate Installation on page 15 NOTE The chimney must have a clay tile liner If it does not the installation must use a positive connection full reline Entire fireplace including chi

¥ Liberty (520) Manual

Contents

Download Pdf Manuals

Related Search

Related Contents

&yen; Liberty (520) Manual

Contents

Download Pdf Manuals

Related Search

Related Contents

¥ Liberty (520) Manual