1000M POE PSE MC User Manual
Contents
1. 0Mbps or 1000Mbps when connected to other network devices network card hub switch etc 2 Line loss is excessive during the fiber wiring Excessive loss in connector plug in and fiber soldering welding and excessive intermediate nodes may cause excessive loss rate or abnormal operation 10 100 1000Base TX to 1000Base FX PoE PSE Media Converter user manual Do not use until you read this manual carefully2. F Brief introduction Many thanks for purchasing PoE PSE Media Converter This product supports IEEE802 3U IEEE802 3z 1000Base Tx Fx protocol and IEEE802 3af PoE PSE application internal AC DC power supply and PSE controller can output up to 25Watts DC48V 540mA or 15 4Watts DC48V 350mA power into CAT5 twisted pair cable The following purchasing guide is for customer s reference F Packing list Please check the following items in the package before installing the media converter PoE PSE media converter tset AC Power cable 1pc User manual 1copy Please contact the dealer immediately for any loss or damage to the above items F Installation 1 Interface RJ 45 interface The transmission media adopts CAT5 twisted pair with maximum length up to 100meters 330feets Fiber interface SC ST fiber interface is of duplex mode type including two interfaces namely TX and RX When the two sets of optical transceiver are interfaced or connected to switch with fiber interface the fiber is in cross connection namely TX RX RX TX direct butting for single optical fiber transceiver module Power supply interface The AC power supply is connected to AC input jack of media converter through the attached AC power cable 2 Connection The network device network card hub or switch etc with RJ 45 interface is connected to RJ 45 jack of media converter through twisted pair And the multi single mode optical fiber is co
3. nnected to SC ST fiber interface of the optical transceiver module Then connect the AC power cables the media converter will work The corresponding LED is on for correct connection See the table below for the LED indicator lamp FX Wet J Cc 7 O FaR aow Fiber EDY L Pare RJ 45 LJ F Description for LED indicator lamp ON 100M 100M OFF 1000M 1000M ON or 10M 1000M OFF ON when connect a correct PD load POE OFF when no load or wrong load Blinking when load is abnormal ON when POE 48V power is ok PWR POE OFF when P OE 48V power is losing or too low F Introduction to dip switches PWR ON when the power supply is turned on Bright when optic fiber cable is connected well but no Link Act data transmission FX Blinking when receiving data Bright when twisted pair is connected well but no data Link Act transmission TP Blinking when receiving data ON when TP link is in full duplex mode FDX TP OFF when TP link is in half duplex mode ON 1000M 1000M OFF 100M or 10M NO Function Status Specification OFF Disable SW1 1 ENROM ON Enable EEPROM SET FX 1000M default SW1 2 FX100M FX 100M SW1 3 NULL Reserved Disable SW1 4 LFP ON Enable OFF OFF Store and Forward mode SW1 5 MODE1 OFF ON Modified cut through mode ON OFF Smart pass through mode SW1 6 MODEO ON ON Pass thro
4. ugh mode Note SW1 2 FX100M SW1 4 LFP will be active only when SW1 1 ENROM is ON SW1 5 MODE1 and SW1 6 MODEO are combined keys to select switch forward mode MODE1 MODE0O F Main features 1 In conformity to IEEE802 3U IEEE802 3z 1000Base Tx Fx standard 2 IEEE802 3af POE PSE compatible 3 Half duplex back pressure flow control Full duplex IEEE802 3x flow control 4 Automatic identification of MDI MDI X cross line 5 Supports link fault pass through function F Technical parameters 1 Standard Protocol IEEE 802 3u 100 Base TX IEEE802 3z IEEE802 3ab standard IEEE802 3af 2 Connector one UTP RJ 45 connector one SC ST connector one AC inlet connector 3 Operation mode full duplex mode or half duplex mode 4 Power supply parameter 100 240V AC 5 Environmental temperature 00 50 6 Relative humidity 5 90 8 TP cable Cat5 UTP cable 9 Optical fiber multi mode 50 125 62 5 125 or 100 140um single mode 8 3 125 8 7 125 9 125 10 Dimensions Power internal 140mm L x 110mm W x40mm H F Cautions 1 This product is suitable for indoor application 2 Put on the dust cover of fiber interface when not used 3 It is forbidden to stare at the TX fiber transfer end with naked eyes 4 Single optical fiber transceiver must be used in pair F Trouble shooting 1 Device is not matched Please select the corresponding network device according to the transfer rate of the product 10Mbps 10
Download Pdf Manuals
Related Search