USER MANUAL
Contents
1. e Never stand directly below the device when mounting removing or servicing the fixture Make sure the area below the installation place is free from unwanted persons during rigging de rigging and servicing e The operator has to make sure that the safety relating and machine technical installations are approved by an expert before using them for the first time The installations should be re inspected every year e Make sure to comply with applicable cooling requirements if any m Getting started making AC supply connections Risk of fire Safety risk The VERSOPLAN II RGB requires an AC power source with sufficient power carriage and correct grounding to ensure safe operation The AC power source must be equipped with a circuit breaker and earth leakage detector Make sure to only use compliant AC supply lines The VERSOPLAN II RGB has an AC outlet that is designed to carry loads of no more than 8A Make sure that all connected devices in a chain fed by the first device do not exceed a maximum of 8A current consumption gt PeS m Getting started making DMX control connections Connect the VERSOPLAN II RGB to a suitable DMX controller where needed and interconnect several units by means of their DMX In Outputs as required The last unit shall be equipped with a proper 120 Ohm termination resistor equipped DMX plug as shown in below drawing Please make sure that all used DMX cables comply to below standard V1 00 02 2012 72. 25 Power Consumption Max 65W Max 95W Dimension WxHxD w o bracket 210 0x210 0x 73 0mm 319 0 210 0x73 0mm Weight 3 10 kg 4 60 kg a Standards This product complies with the following standards EU electrical safety EN60598 1 2008 EN60598 2 1 1989 EU photobiological safety c cccscoscssereeeesereeeseonenseeesesdeneteseeneesenerse EN 62471 2008 EU EMG ease ens scetes iser saeka ia EN55015 2006 A1 2007 EN61547 1995 A1 2000 EU AnMOMiCs srren eate r aaie EEE eee ees EN61000 3 2 2006 EU FICKGR sahescehorseteanicesderietebigeaheteboee ck a e aa EN61000 3 3 2008 US Safat sss wsgassccte ce ienaiiino i nadetab wav n a anida iii UL60065 WS EMG rroia r e a a Aa A ASE A LE a EAn FCC Part 15 This product meets both the EMC Directive 2004 108 EC and the Low Voltage Directive 2006 95 EC V1 00 02 2012 14 User Manual VersoPlan ll RGB gt gt gt WARNING Fire hazard WARNING Laser radiation Risk of surface damage WARNING LED light emission Risk of eye injury m Security advice before use gt akwWN gt gt gt gt V1 00 02 2012 General advice Read this manual completely before using the product Keep this manual in your records for future reference Follow all instruction printed in this manual Follow all printed security advice on the product itself Take care of enough distance between this product and sources of hum and noise like ele
3. User Manual VersoPlan ll RGB DMX output DMX output DMX input DMX input FE Fe Is y f Ma S MA N G2 le 2 0 0 5 Pin 5 Pin 3 Pin SIGNAL SHIELD GROUND RETURN OV TERMINATION INNER CONDUCTOR DATA COMPLEMENT INVERTED INNER CONDUCTOR DATA TRUE NON INVERTED Termination resistor m Operation USER INTERFACE User interface overview MODE selection button UP Button DOWN Button Display showing the Mode DMX address etc RON V1 00 02 2012 User Manual VersoPlan ll RGB DMX input DMX output AC output AC input ONO Upon the user s choice the unit can work in stand alone automatic mode or with fixed colors or it may be controlled by external DMX controllers Available modes C Color Mode Press the MODE button until the display shows Cxx indicating operation in C mode with chosen preset xx then choose by using the UP DOWN buttons one of the 13 color presets as shown in the list below The output level brightness can be set in 10 levels 10 20 30 40 50 60 70 80 90 100 This is done by pressing and holding the MODE button and then pressing the UP or DOWN buttons to change the brightness Note that the brightness setting using the on board user interface can only be done in COLOR mode and is a global setting for all stand alone modes which means that the same chosen brightness remains
4. applicable for the AUTO and SOUND modes as well The brightness chosen on the unit itself however has no influence in any of the DMX modes In C mode the unit does not receive any values from the DMX input but generates related DMX values on the output 3CH according to the selected preset so that further units can show the same behaviour if they are connected by DMX signal cables and set to d3 Mode with selected start address 001 If you leave mode C for any reason and come back later into mode C the unit will recall the last chosen color preset even if the unit was switched off in between Available color presets Preset Colour R G B CO White W 0 0 0 C1 Red R 255 0 0 C2 Green G 0 255 0 C3 Blue B 0 0 255 C4 Yellow Y 255 170 0 C5 Pink P 255 0 255 C6 Turquoise T 0 255 255 C7 Lime L 127 255 0 C8 Orange O 255 85 0 c9 Marine M 0 127 255 C10 Frog F 0 255 127 C11 Lavender V 127 0 255 C12 Candy C 255 0 127 C13 Blackout 0 0 0 V1 00 02 2012 9
5. channels with the following functional assignment CH1 Choice of fixed colors if CH3 lt 25 or fade switch pattern presets if CH 2 25 CH2 000 255 Master Dimmer 0 100 CH3 Function choice C Color static and A Auto mode speed setting for A mode CH3 0 24 selects the fixed color C mode Color choice by CH1 CH3 25 234 selects the auto A mode and determines the speed Pattern choice by CH1 CH3 235 255 selects the sound to light S mode Pattern choice by CH1 CH4 000 049 Strobe off 050 255 Strobe rate 050 slow 255 max speed 23 Hz Display on off The display of the unit will turn off after 25 seconds of not receiving any user commands through the user interface buttons On the first hit of any button the display will light up again this first hit will not change any settings only when you press any button after that settings will be affected V1 00 02 2012 13 User Manual VersoPlan ll RGB d3 Mode DMX 3CH Mode Press the MODE button on the unit itself until the display shows d3 indicating operation in d3 DMX 3 channel mode Shortly after that the display shows the DMX starting address You can choose any DMX starting address by simply using the UP DOWN buttons on the unit itself The chosen DMX address comes effective approximately 3 seconds later and will show up on the display on the unit itself in alternation to the d This allows control of the un
6. 2Hz 480 BPM 8 0HZz This is done by pressing and holding the MODE button and then pressing the UP or DOWN buttons to change the speed Note that the speed setting using the on board user interface can only be done in AUTO mode The output level brightness can be set in 10 levels 10 20 30 40 50 60 70 80 90 100 To do this with the on board user interface the user must change into COLOR mode first and make a global brightness adjustment as described in the COLOR mode chapter In Axx mode the unit does not receive any values from the DMX input but generates related DMX values on the output 3CH according to the selected pattern so that further units can show the same behaviour if they are connected by DMX signal cables and set to d3 Mode with selected start address 001 If you leave mode Axx for any reason and come back later into mode Axx the unit will recall the last chosen pattern even if the unit was switched off in between Available pattern presets Fade Transition Switch Transition Strobes 16Hz A00 Red Green A10 Red Green A20 Strobe white A01 Green Blue A11 Green Blue A21 Strobe red A02 Red Blue A12 Red Blue A22 Strobe green A03 Red Yellow A13 Red Yellow A23 Strobe Blue A04 Orange Frog A14 Orange Frog A05 Pink Blue A15 Pink Blue A06 Turquoise Pink A16 Turquoise Pink A07 Red green blue A17 Red green blue A08 Yellow tu
7. EEN CH3 000 255 Dimmer BLUE CH4 000 127 Master Dimmer 0 100 CH4 128 227 Strobe speed 128 slow 227 max speed 23 Hz CH4 228 255 Master Dimmer 100 Strobe off d5 Mode DMX 5CH Mode Press the MODE button on the unit itself until the display shows d5 indicating V1 00 02 2012 12 User Manual VersoPlan ll RGB order to avoid any damage on the unit due to AC voltage peaks 7 In cause of not correct function of this unit or damaged AC cord or other damaged parts pull immediately the AC plug out of the wall outlet and hand the unit over to the authorized service for a security check 8 To meet all aspects of functionality and security during mainte nance work to be preformed on this unit all parts should be replaced by genuine spare parts Consequently take care of your dealer or maintenance company to be authorized by the manufacturer a Health advice This unit produces and absorbs electromagnetic radiation The strength of radiation and the sensitivity for disturbing interference matches the CE and FCC requirements A corresponding sign is printed on the backside of the unit Any change or modification may affect the behavior of the unit concerning electromagnetic radiation with the CE requirements eventually not to be met any more The manufacturer takes no responsibility in this case Functional advice This unit is immune to the presence of electromagnetic disturbances both condu
8. USER MANUAL VersoPlan ll RGB DMxX controlled RGB LED Spot For firmware 50 015 0018 00117 1 00 MKIII ENGLISH Page 2 14 AAN MULTIFORM RevA 01 5 2013 Order code 12 015 0113 80500 1 01 User Manual VersoPlan ll RGB a Introduction Congratulations on the purchase of a Multiform branded item and the trust having been put in us with this decision Multiform is one of the leading global manufacturers of professional lighting equipment and has decades of experience in design production and quality assurance To meet your requirements this unit has been designed and built to the highest standards so that we can assure you that you have made a good and satisfying investment To take full advantage of all possibilities and for your own safety and the safety of your environment please read these operating instructions carefully before you start using the unit Product description The VersoPlan Il RGB series are high power color mixing solid state lighting fixtures with a broad range of possible applications from show lighting to architectural installations SAFETY INFORMATION Read the safety precautions in this chapter before installing powering up operating or servicing this device Failure to do so may void the product warranty and releases the manufacturer from all product liability gt m Symbols used in this manual The following symbols are used to identify important safety information on the product and in t
9. connect the unit from AC supply before any kind of cleaning on 3 User Manual VersoPlan ll RGB A A VAN V1 00 02 2012 AD the product Use smooth and dry cloth only for cleaning Do not expose this unit to any dripping or splashing liquids and do not place objects filled with liquids such as vases on the unit Do not operate this unit near to open water or in high humidity Choose the position of the AC cord according to the lowest risk of damage by foot steps or by squeezing it Do not open the unit for service there are no user serviceable parts inside Warranty will be void in any case of unauthorized service by the user or other not authorized persons Protection from fire 1 2 3 Take care of not placing the unit near sources of heat e g powerful amplifiers fog machines Allow at least about 0 15m 6 ins between this unit and other devices or a wall to allow for proper cooling Take always care of sufficient air convection in the unit s environment to avoid overheating Make sure air convection slots are not blocked Do not operate this unit in environmental temperatures exceeding 35 degrees Celsius Be sure this fixture is kept at least 0 75m 30ins away from any flammable materials decoration etc Do not stick filters masks or other materials directly on the LEDs or the LED cover screen Check the total maximum power of your AC wall outlet if you connect several units to one wall outl
10. cted and radiated up to a certain level Under peak conditions the unit is classified to show a class C performance criteria and may encounter temporary degradation or loss of function which may need manual help to recover In such case disconnect the AC power from the unit and reconnect it again to recover a Environmental advice This unit is built to conform to the ROHS standards and the WEEE directive 2002 96 EC of the European Parliament and of the Council of the European Union Under these regulations the product shall not be discarded into regular garbage at the end of its life but shall be returned to authorized recycling stations LA m LED Lifetime advice LED lifetime is determined by the gradually declining brightness of a LED over time with a point of 50 brightness reduction marking the defined end of its lifetime The driving factor of this effect is the heat that the chip inside the LED is exposed to While a chip may under ideal circumstances reach to more than 100000 hours of lifetime the real world lifetime may only be 30000 to 50000 hours or less if the LED is exposed to excessive heat which can be caused by continuously running all LEDs inside this device at full power and operating the unit in high environmental temperatures If improving the lifespan expectancy is a priority take care of providing for lower V1 00 02 2012 5 User Manual VersoPlan ll RGB operational temperatures This may include forc
11. ctric motors and transformers D Carry this product with greatest care Punches big forces and heavy vibration may damage this product mechanically Protection from eye injury 1 Warning Depending on the configuration of the device this device may reach or exceed the limits of EN62471 risk group 2 and may hence reach to risk group 3 To avoid eye injury do not look into the beam from a distance of less than 8 5 m 27 ft 11 ins from the front surface of the fixture without protective eyewear such as shade 5 welding goggles At larger distances light output is harmless to the naked eye provided that the eye s natural aversion response is not affected Do not view the beam directly with optical instruments such as magnifiers telescopes binoculars or similar optical instruments that may concentrate the light output Ensure that during setup and DMX programming no persons are inside a 8 50m 27 ft 11 ins vicinity of the device s front surface to avoid that they may accidently be exposed to the light beam Protection from electric shock 1 Only connect this unit to a mains socket outlet with protective earth connection ground fault earth fault and overload protection 2 Where the mains plug or an appliance coupler is used as a dis connect device such device shall remain readily operable 3 To pull the AC Cord out of the wall outlet or the units AC socket never pull the cable itself but only the AC plug 4 Dis
12. ed external cooling and or the reduction of overall projection intensity m Unpacking Please check that the box contains the following items and contact your dealer immediately for replacement if any part is missing Main parts 1 pc VERSOPLAN II RGB main unit 1 pc mains cable 1 pc operation manual m Getting started choosing a location Risk of fire The VERSOPLAN I RGB has been designed to work in dry indoor environments at environmental temperatures up to 35 degrees Celsius For proper operation the unit must be operated with unobstructed air convection to its outside metal case Operate the VERSOPLAN II RGB in environments with more than 35 degrees environmental temperature or more than 75 relative humidity Operate the VERSOPLAN II RGB in any closed environment smaller than 10cbm unless forced air convection is provided m Getting started secure mounting The VERSOPLAN II RGB can be mounted in various ways Floor standing operation e Turn the bracket to the lower side of the unit and fold out the second inlaying bracket e Place the unit in a secure position where it can neither be touched by anyone or could possibly become an objective for anyone to stumble e Make sure to comply with cooling requirements of the used power supply if any Hanging Rigging ceiling mounted operation Risk of injury Overhead mounting requires extensive experience AN including among others calculating working load limits good
13. et and avoid any overloading If the device itself has an AC outlet for providing power to other units make sure to not exceed the specified maximum load Protection from injury and damage 1 2 Never use any accessories or modifications not authorized by the manufacturer of this unit Choose a location for operation where the unit is protected from vibration and where a fixed mounting position is provided In case of overhead mounting follow applicable rigging requirements Before plugging the AC cord in the wall outlet check whether the AC plug the mains voltage and frequency are the same as this product is specified for If not contact you dealer immediately The surface of the device may get hot during operation and heat sink areas may reach to or exceed the limits of EN60950 Do not touch heat sink areas of the device during operation and allow 20 minutes of cool down time after powering off before touching If fluids have spilled into the unit or small parts have intruded the unit immediately switch off the unit and hand it over to the authorized service for a security check Disconnect the unit from AC supply by pulling the AC plug out of the wall outlet or the units AC socket during a thunder storm in 4 User Manual VersoPlan ll RGB operation in d5 DMX 5 channel mode Shortly after that the display shows the DMX starting address You can choose any DMX starting address by simply using the UP DOWN buttons o
14. his manual WARNING Read manual before installation operation or servicing WARNING Safety hazard Risk of injury or death WARNING Hazardous voltage Risk of severe or fatal electric shock WARNING Shock hazard Equipment must be properly grounded WARNING Hot surface Risk of skin burn or skin irritation DEEeb V1 00 02 2012 2 User Manual VersoPlan ll RGB a Maintenance This device does not need regular maintenance It is protected by an internal fuse located on the power supply PCB If this fuse fails this usually indicates an internal fault requiring servicing by a qualified engineer The fuse shall only be replaced by a fuse of same specification and the replacement has to be made by qualified personnel obeying applicable safety rules m Technical data VERSOPLAN II RGB Mains MPU os ctecweiigenartateneshessbaneeevecs nieces E a EER santas AC100 250V 50 60Hz Power Supply ype eniinn ris la eneee r eE AEA TOA EE RA ELA switch mode F SSE a e E EE E E internal see service manual DMXSCONNGCH ONS in nasaan u anaa ae 3 pin XLR Male Female Modulation Type 0 0cececeeeeee ee eceeeeeeeteeeeeeaeaeees Pulse Density Modulation PDM COmtrol PROTOCOL sa c 5ccececnechesscscpesscocaseatsiesececsicecsesach scsueaaiecss lt cestanisscanetmeaseces DMX 512 1990 Version data VersoPlan HT3018 VersoPlan HT3030 LEDs 18x3W 3x350mA 30x3W 3x350mA 18 RGB 30 RGB TriLED TriLED Dispersion 25
15. it by any external DMX signal sending on the chosen channels Once such signal is received a LED on the lower right side of the d in the display indicates that a DMX signal is present The unit receives DMX values on a packet of 3 consecutive DMX channels with the following functional assignment CH1 000 255 Dimmer RED CH2 000 255 Dimmer GREEN CH3 000 255 Dimmer BLUE Note If you wish to operate a unit as a slave to another unit which is operating in a stand alone mode like COLOR AUTO or SOUND mode then you must choose the d3 mode and set the starting address to 001 d4 Mode DMX 4CH Mode Press the MODE button on the unit itself until the display shows d4 indicating operation in d4 DMX 4 channel mode Shortly after that the display shows the DMX starting address You can choose any DMX starting address by simply using the UP DOWN buttons on the unit itself The chosen DMX address comes effective approximately 3 seconds later and will show up on the display on the unit itself in alternation to the d This allows control of the unit by any external DMX signal sending on the chosen channels Once such signal is received a LED on the lower right side of the d in the display indicates that a DMX signal is present The unit receives DMX values on a packet of 4 consecutive DMX channels with the following functional assignment CH1 000 255 Dimmer RED CH2 000 255 Dimmer GR
16. knowledge of the installation material being used and periodic safety inspection of all installation material and the unit If you lack such qualifications do not attempt the installation yourself Improper installation can result in body injury Be sure to complete all rigging and installation procedures before applying power to the unit V1 00 02 2012 6 User Manual VersoPlan ll RGB In S Sound to Light mode the speed of the pattern progress is determined by the signal picked up by the internal microphone Every detected beat will e Temporarily speed up the color fade in pattern presets 0 9 creating a pulsating effect in synchronization with the music e Switch to the next pattern step in pattern presets 10 19 creating a chasing effect in synchronization with the music The output level brightness can be set in 10 levels 10 20 30 40 50 60 70 80 90 100 To do this with the on board user interface the user must change into COLOR mode first and make a global brightness adjustments as described in the COLOR mode chapter In S mode the unit does not receive any values from the DMX input but generates related DMX values on the output 3CH according to the selected pattern so that further units can show the same behaviour if they are connected by DMX signal cables and set to d3 Mode with selected start address 001 If you leave mode SLx for any reason and come back later into
17. mode SLx the unit will recall the last chosen preset even if the unit was switched off in between Available pattern presets transition is switching Preset Transition Color sequence So Fading Red Green S1 Fading Green Blue S2 Fading Red Blue 3 Fading Red Yellow 4 Fading Orange Frog 5 Fading Pink Blue 6 Fading Turquoise Pink S7 Fading Red green blue 8 Fading Yellow turquoise pink S9 Fading Red green orange turquoise blue pink S10 Switching Red Green S11 Switching Green Blue S12 Switching Red Blue S13 Switching Red Yellow S14 Switching Orange Frog S15 Switching Pink Blue S16 Switching Turquoise Pink S17 Switching Red green blue S18 Switching Yellow turquoise pink S19 Switching Red green orange turquoise blue pink Note patterns Sx0 Sx9 are identical to the patterns used in Axx mode V1 00 02 2012 11 User Manual VersoPlan ll RGB A Auto Mode Press the MODE button on the unit itself until the display shows Axx indicating operation in A mode with chosen pattern xx then choose by using the UP DOWN buttons one of the 24 pattern presets as shown in the list below The speed of the pattern progress can be set in 10 levels 3 BPM 0 05Hz 6 BPM 0 1Hz 30 BPM 0 5Hz 60 BPM 1 0Hz 90 BPM 1 5Hz 120 BPM 2 0Hz 150 BPM 2 5 Hz 200 BPM 3 2Hz 320 BPM 5
18. n the unit itself The chosen DMX address comes effective approximately 3 seconds later and will show up on the display on the unit itself in alternation to the d This allows control of the unit by any external DMX signal sending on the chosen channels Once such signal is received a LED on the lower right side of the d in the display indicates that a DMX signal is present The unit receives DMX values on a packet of 5 consecutive DMX channels with the following functional assignment CH1 000 255 Dimmer RED CH2 000 255 Dimmer GREEN CH3 000 255 Dimmer BLUE CH4 000 255 Master Dimmer 0 100 CH5 000 049 Strobe off 050 255 Strobe rate 050 slow 255 max speed 23 Hz dP Mode DMX Preset Mode Press the MODE button on the unit itself until the display shows dP indicating operation in dP DMX Preset mode Shortly after that the display shows the DMX starting address You can choose any DMX starting address by simply using the UP DOWN buttons on the unit itself The chosen DMxX address comes effective approximately 3 seconds later and will show up on the display on the unit itself in alternation to the d This allows control of the unit by any external DMX signal sending on the chosen channels Once such signal is received a LED on the lower right side of the d in the display indicates that a DMX signal is present The unit receives DMX values on a packet of 4 consecutive DMX
19. rquoise A18 Yellow turquoise pink pink A09 Red green A19 Red green orange orange turquoise turquoise blue pink blue pink Note Patterns Ax0 Ax9 are identical to the patterns used in S mode S Sound to Light Mode Press the MODE button on the unit itself until the display shows Sxx indicating operation in S mode with chosen pattern xx then choose by using the UP DOWN buttons one of the 20 pattern presets as shown in the list below V1 00 02 2012 10 User Manual VersoPlan ll RGB e Leave the inner and outer bracket folded e The unit should be installed out of reach of people and outside areas where persons may walk by or be seated e Make sure that the installation area can hold a minimum point load of 10 times the device s weight e In fixed installations fix the unit with self locking screws nuts to the mounting point e When mounting the unit to truss be sure to secure an appropriately rated clamp to the hanging yoke using a M10 screw fitted through the center hole of the hanging yoke e Where required secure the installation with an appropriate safety cable Always use a certified safety cable according to EN60598 2 17 Section 17 6 6 that can hold 12 times the weight of the device when installing the unit This secondary safety attachment should be installed in a way that no part of the installation can drop more than 20cm if the main attachment fails
Download Pdf Manuals
Related Search