1112PS Installation Instruction 1203B
Contents
1. 3 3 i El REV 06 13 DOC1203B PAGE 9 IED GLOBALCOM IED1112PS INSTALLATION INSTRUCTIONS Figure 9 Securing Cover Plate Over the Connectors INSTALL PRIMARY POWER SUPPLY Unpack the primary power supply module IED1112PSM and install it as shown in Figure 10 Press firmly until the locking tab snaps into place Figure 10 Installing Primary IED1112PSM Power Supply OPTIONAL INSTALL SECOND BACKUP POWER SUPPLY If a second power supply module IED1112PSM was purchased for redundancy it will be boxed separate ly Remove the blank cover plate on the rear of the unit as shown in Figure 11 Remove the module from its packaging and install in the open slot as shown in Figure 12 PAGE 10 DOC1203B REV 06 13 INSTALLATION INSTRUCTIONS IED GLOBALCOM IED1112PS Figure 11 Power Supply Slot Cover Removal W Figure 12 Installing Second IED1112PSM Power Supply Module CONNECT POWER PLUG Attach the AC power cables by plugging them into the power supply modules as shown in Figure 13 Note if there is only one supply only one power plug will be installed Figure 13 Connect Power Plugs REV 06 13 DOC1203B PAGE 11 SPECIFICATIONS ELECTRICAL Teg SEI VO stot maten quests E E dunmseincciatbtemedonn ss 120 240VAC 50 60HZz 2 Rated Input Current per suppl 8 Amps Max 3 Ralod UTD UN e Wie EEN 12VDC 5 4 Rated Output C rrent OIL EE 37 Amps 5 Rated Output Current per output E2. cites alle ceci tim scr on sts am ase sen ania dei mn tec 6 LED GPS INS TE ut ei BE 8 UNPACKING AND PREPARING THE EC RE 8 INSTALL UNIT INTO A RACK eee hates bee sees testes etal Gets cate eee eee ces tate teeteneenedenes 8 Ile KA E EE 9 CONNECT FAULT RELAY AND POWER OUTPUT CABLES eee 9 INSTALL PRIMARY POWER SUPPLY E 10 OPTIONAL INSTALL SECOND BACKUP POWER GUY 10 CONNECT Oo tegen erte ren rarer ee ee nee oe eee ee 11 SEET 12 SN Bice aan eae cnet E es te seg ec cee nn E 12 REV 06 13 DOC1203B PAGE 1 IED GLOBALCOM IED1112PS INSTALLATION INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Read these instructions Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used Heed all warnings use caution when moving the cart apparatus combination to avoid injury from tip over Keep these instructions Follow all instructions Unplug this apparatus during lightning storms or Do not use this apparatus near water ER when unused for long periods of time Clean only with dry cloth Refer all servicing to qualified service personnel Ser Do not block any ventilation openings Install in accordance with vicing is required when the apparatus has been dam the manufacturer s instructions aged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been ex posed to ra
3. external discharge network This is most important in the case of high voltage or high capacitance capacitors If one terminal is connected to ground connect the discharge network between the other terminal and ground If neither terminal of the capacitor is grounded connect the network across the capacitor terminals Connecting a short circuit across the terminals is not recommended Doing so can produce extremely high currents and a flash which can injure the eyes vaporize metals and cause burns PRECAUTIONS WHEN WORKING ON ENERGIZED EQUIPMENT When it is necessary to work on energized equipment think ahead and anticipate every hazard Never work alone on energized equipment Interlock switches are installed on some of the doors and panels to break the power circuits when the enclosure is entered When it is necessary to work within such an enclosure on energized equipment the interlock may be bypassed Extreme caution should then be exercised as dangerous voltages are present within the unit AC POWER CIRCUITS PAGE 4 Equipment obtaining power from a secondary distribution system should be grounded at all times by means of a third grounding wire on the power lines Equipment permanently wired to a secondary distribu tion system should also be grounded separately by connection to a grounding bus or ground rod with a sufficiently large conductor to handle the current expected if the secondary source is accidentally shorted to the equipme
4. purposes only and are not intended to refer to any actual organization or an endorsement of any kind Innovative Electronic Designs IED 5 0 0ACS 500ACS Announcement Control System CAS Courtesy Announcement System T CAS FAS Flight Announcement System IED On Call IED On Call amp Design and LANcom are all registered trademarks or trade marks of Innovative Electronic Designs LLC in the United States and or other countries CobraNet is a registered trade mark of Cirrus Logic in the United States and or other countries Microsoft Windows Windows Vista Windows 7 Windows Server SQL Server and Internet Explorer are all registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries Innovative Electronic Designs LLC 9701 Taylorsville Road Louisville KY 40299 United States of America www iedaudio com Document Number 1203B PAGE il DOC1203B REV 06 13 INSTALLATION INSTRUCTIONS IED GLOBALCOM IED1112PS TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS eegenen eege EEN 2 SAFETY dl 2 SAFETY CONSIDER ue LE 3 SAFE TY PREGA TE 3 GENERAL PRECAUTIONS EE 3 PRELIMINARY PRECAUTIONS aiteenttotzmotsmestolcetttent cmmesnttmemtontetamesiamststeme 3 PRECAUTIONS WHEN MEASURING HIGH VOLTAGE POTENTIALS 4 PRECAUTIONS WHEN WORKING ON ENERGIZED EQUIPMENT ees 4 AC FOWER CIRCOM KE 4 Eegeregie eege eege 5 DESCRIPTION WE 5 CONNECTIONS aie sie ce nace wns civ micn pets Sie
5. that use 2 pin Phoenix plugs with 5 08mm spacing Each port can be used to power a GLOBALCOM device using the supplied adaptor cable 8 Output Port Fuses 8 Each output port is protected by a 5A fuse Use a 5A 32VDC fast blow blade style fuse for re placement in the event that a fuse is blown 9 Fuse Status LEDs 8 Each output port has a green status LED located directly above the fuse This IED illuminates green when power is available at the port The LED will turn off when the fuse is blown or removed indicating that power is not available at that output port REV 06 13 DOC1203B PAGE 7 IED GLOBALCOM IED1112PS INSTALLATION INSTRUCTIONS IED1112PS INSTALLATION 7 Wa Before performing the following procedure review the safety instructions on the previous pages NOTE This equipment is intended for installation in a restricted access location UNPACKING AND PREPARING THE UNIT Unpack the unit from its shipping carton and identify any accompanying components that may have been included Attach the rack ears as shown in Figure 5 to allow the unit to be mounted in a standard 19 equip ment rack Adjust the ear positions so the front of the ear is even with the front of the unit and tighten the screws securely AN K K Figure 5 Attaching Rack Mount Ears to the Unit INSTALL UNIT INTO A RACK The IED1112PS requires one rack unit 1 RU of available space and a recommended mounting depth of 18 to allow adequate c
6. 112PS The connectors are secured using the supplied cover plate to prevent unwanted disconnections A second 1112PSM power supply module can be added to provide redundancy If a module fails the remaining module will assume the full load A module can be replaced while the other module is left on without interrupting power to the system A relay is provided that will de en ergize if a power supply module has failed This closure can be monitored through the supervision system REV 06 13 DOC1203B PAGE 5 IED GLOBALCOM IED1112PS INSTALLATION INSTRUCTIONS CONNECTIONS OC O C littl FED O O _PB2BD8808505805009000050000500005000000000000000000000S00TI OO A Figure 1 1ED1112PS Front View 4 5 a H H o D m O DO U O D Of an O 1 es C Figure 2 ED1112PS Rear View 1 Power LED This LED will illuminate when the unit is powered on 2 Fault LED This LED will illuminate when a power supply fault is present or if an output fuse has failed This corresponds with the de energizing of the fault relay 3 U
7. E 4 6 Amps 6 Relay Contact Rating EN Form C 1A 30VDC 0 3A 125VAC T OUPO FUG CS EE 5 Amp 32VDC Fast Blow Blade Fuse MECHANICAL ds Me e EE 4 4 cm 1 75 2 Width without TACK mount GAPS EE 43 2 cm 17 de BEDU EE 31 1 cm 12 25 4 Recommended Mounting Depth EE 45 7 cm 18 5 Weight with 1 x IED1112PSM model 5 9 kg 13 Ib 6 Weight with 2 x IED1112PSM mmoguleeh seetgseereef deed EeeEedEeteeed eEeuel Ze eEseedeCEeeed E enda 7 1 kg 15 6 Ib ENVIRONMENTAL 1 Operating Temperature Range siciecesctevvcduuvea view dreet eebe dgeE 32 F 104 F 0 C 50 C 2 Storage Temperature Range sesessssrsnrrnrrrrrsrsnssrsrrnrrrrrrrrnssssnrnnrrrrereeene 40 F 158 F 40 C 70 C CONNECTORS Wig te a ON EEN IEC 60320 Type C 13 2 Output Power typical Of EE 2 pin Phoenix 5 08 mm spacing SE 3 pin Phoenix 3 8mm spacing COMPLIANCE 1 SAFETY UL60950 1 Ed 2 Listed CAN CSA C22 2 No 60950 1 07 Ed 2 Certified IEC 60950 1 2005 AM 1 2009 EN 60950 1 2 6 A1 1 2009 A1 2010 CB Certificate 2 FCC EMC CFR Title 47 Chapter I Part 15 Subpart B ICES 003 Issue 4 2004 AS NZS CISPR 22 2005 CISPR 22 Ed 5 2005 A1 EN 55022 2006 A1 CISPR 24 Ed 1 1997 A1 A2 EN 55024 1998 A1 A2 IEC 61000 3 2 Ed 3 2005 A1 A2 EN 61000 3 2 2006 IEC 61000 3 3 Ed 2 2008 EN 61000 3 3 1995 A1 A2 FCC NOTICE This device complies with part 15 of the FCC Rules Operation is
8. IED GLOBALCOM Installation Instructions IED Announcement Control System IED1112PS Ww LE D GLOBALCOM REV 06 13 DOC1203B 2013 Innovative Electronic Designs LLC IED GLOBALCOM IED1112PS INSTALLATION INSTRUCTIONS Copyright 2013 Innovative Electronic Designs LLC All Rights Reserved If this document is distributed with software that includes an end user agreement this document as well as the software described in it is furnished under license and may be used or copied only in accordance with the terms of such license Except as permit ted by any such license no part of this document may be reproduced or transmitted in any form or by any means electronic or mechanical including photocopying recording storage in an information retrieval system or otherwise without the prior written permission of Innovative Electronic Designs LLC Please note that the content in this guide is protected under copyright law even if it is not distributed with software that includes an end user license agreement The content of this document is furnished for informational use only and is subject to change without notice It should not be con strued as a commitment by Innovative Electronic Designs LLC Innovative Electronic Designs LLC assumes no responsibility or liability for any errors or inaccuracies that may appear in the informational content contained in this document Any reference to company names in examples are for demonstration
9. SB Power Port 5V DC power is available at this port to allow charging of portable devices with a USB connection 4 Power Supply Modules A single IED1112PSM power supply module is included with the IED1112PS and will be installed in one of the two available bays A second IED1112PSM power supply module can be added to the unit to provide redundant power When two modules are installed they will share the total load placed on the unit If either module fails the total load will be assumed by the remaining module 5 Power Supply Status Indicators These LED s indicate the operational status of the individual power supply module Green Power Good Yellow Fault Green AC Good Figure 3 ED1112PSM Status Indicators PAGE 6 DOC1203B REV 06 13 INSTALLATION INSTRUCTIONS IED GLOBALCOM IED1112PS 6 Fault Relay Terminal This connector utilizes a 3 pin Phoenix plug with 3 8mm spacing to access the status of the fault relay The relay is energized when no fault condition is present and the contact is closed between the NC and C terminals The relay will de energize when a power supply fault is present and the contact is closed between the NO and C terminals The fault relay will trip if a power supply has failed or if an output fuse has failed or has been removed FAULT RELAY No C NO Figure 4 Fault Relay Connector 7 Power Output Terminals 8 There are eight 8 output ports available
10. ance is ongoing personnel in the equipment areas shall have an effective communication among these areas in order to protect people if any accident occurs PRELIMINARY PRECAUTIONS Precautions which are applicable to general electrical or electronic maintenance are as follows a Check yourself Wear no article that might catch on equipment or that might act as a conductor b Check the working area The equipment area shall be clean and dry If possible stand on a special insulator such as a rubber mat There should be ample working space and good lighting c Check the tools Always use proper tools and check them for their safe condition Use screwdrivers with plastic handles Check test equipment periodically and examine test leads carefully as the slight est break in insulation is dangerous REV 06 13 DOC1203B PAGE 3 IED GLOBALCOM IED1112PS INSTALLATION INSTRUCTIONS d Check the procedures Study the entire procedure before taking the first step Consult the circuit dia gram frequently to obtain an understanding of what is accomplished at each step Know what is in the equipment and how it differs from others on which you have worked e Be aware that high voltages may be present across terminals that are normally low voltage due to equipment breakdown Be careful when measuring low voltages in equipment containing high voltage circuits f Do not make resistance measurements with power on g Do not work within the equipment w
11. her or not it is safe to proceed Before performing any step in a procedure be sure that the preceding step has been properly executed and correct results obtained Cleanliness and good housekeeping in all installation areas are major factors in effective accident prevention Tools and equipment should be maintained in good working order and should always be returned to their proper storage place after usage Cleaning agents and other cleaning aids should be removed from the equipment areas immediately upon completing the task at hand GENERAL PRECAUTIONS Changes modifications or additions in connection with the IED system equipment shall not be made with out explicit authorization of IED Safety devices found on mechanical and electrical and electronic equipment are put there for the protec tion of personnel and equipment These devices must be maintained in good working order and operative at all times Safety devices shall never be removed or bypassed unless specifically authorized by the IED factory Where safety devices have been rendered inoperable by proper and specific authorization ad equate notices shall be posted to warn personnel of the potential hazard Avoid the use of flammable or toxic cleaning fluids and the use of carbon tetrachloride is prohibited Maintenance of the equipment shall be at least what is specified in the IED manuals and literature and performed only by qualified personnel Whenever operation and mainten
12. in or moisture does not operate normally or has been dropped Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than CAUTION the other A grounding type plug has two blades and a third DEE grounding prong The wide blade or the third prong is provided DO NOT OPEN for your safety If the provided plug does not fit into your outlet SiEGUE DE CHOC EIECTRIGUE consult an electrician for replacement of the obsolete outlet NE PAS OUVRIR CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL Protect the power cord from being walked on or pinched par ticularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachments accessories specified by the manufac turer WARNING To reduce the risk of fire or electric shock do not expose this apparatus to rain moisture dripping splashing or place objects filled with liquids on the equipment WARNING If apparatus is equipped with Class grounding plugs for safety purposes it must be connected to MAINS that employ a protective earth ground connection WARNING The MAINS plug on this device may be used as the DISCONNECT DEVICE for MAINS power and
13. ithout the presence of a person who is capable of rendering aid and who is familiar with the procedure for emergency shutdown of the equipment PRECAUTIONS WHEN MEASURING HIGH VOLTAGE POTENTIALS Observe the following precautions when measurements must be performed on circuits with potentials over 48 volts a Do not measure potentials over 48 volts without the presence or assistance of a person who is capable of rendering aid and who is familiar with the procedure for emergency shutdown of the equipment b Be sure you are not grounded when you are adjusting equipment or using measuring equipment Stand on a rubber mat or other insulator if possible Be sure the equipment area is clean and dry In general use only one hand when servicing live equipment c lfa test meter must be held or adjusted while voltage is applied ground the case of the meter before starting a measurement Do not touch the live equipment or personnel working on live equipment while holding the meter The common terminal on some A C electronic voltmeters is at ground potential never connect the common terminal to any point above ground potential d High voltage high capacitance capacitors should be discharged before servicing is started A WARNING Discharging must be done carefully and judiciously First ascertain whether there is a built in bleeder network If so wait a minute or two for the capacitor to discharge through the network Otherwise use an
14. learance for cabling Select a location in the 19 rack for the unit based on proximity to the device that will be served by the unit Mount the unit using suitable screws for the rack being used two per rack mount ear Please refer to any safety and installation instructions that came with the rack prior to assembly Figure 6 Mounting Unit in a Rack PAGE 8 DOC1203B REV 06 13 INSTALLATION INSTRUCTIONS IED GLOBALCOM IED1112PS INSTALL FUSES If the unit shipped with fuses un installed install them now by inserting them straight into the fuse sockets provided for each power output connection as shown in Figure 7 Figure 7 Inserting Fuses CONNECT FAULT RELAY AND POWER OUTPUT CABLES The optional fault relay connection may be connected via the Phoenix connector in the center of the back of the unit Also attach power output cables for all of the required devices to be powered by the 1112PS as shown in Figure 8 Figure 8 Connecting Fault Relay and Output Power To ensure the power output connections and relay connection do not get accidentally pulled out nor the fuses accidental damaged install the provided cover plate to secure them using the provided screws as shown in Figure 9 Correct Incorrect CAUTION Ensure that wire is stripped no more than 7mm from the end in order to prevent the wire from shorting to the rear cover plate Do not allovv any Kg insulation to be crimped in the compression terminal
15. must remain readily operable WARNING Installation and maintenance of IED equipment is to be made by trained qualified personnel and must conform to all applicable local codes WARNING If unit contains a lithium battery there is a danger of explosion Replace only with the same or equivalent type SAFETY SYMBOLS Labeling on products and the nstallation Instructions amp User Manual may use safety related graphical sym bols as shown below to note safety requirements A Lightning Bolt The lightning flash with arrowhead symbol within an equilateral triangle WARN ING symbol is intended to alert the user to the presence of un insulated dangerous voltage within the product s enclosure that may be sufficient in magnitude to constitute a risk of electric shock to persons or domestic animals A Exclamation Point The exclamation point within an equilateral triangle CAUTION symbol is intended to alert the user to the presence of important operating and maintenance servicing instructions or a hazard that can damage equipment A Do not proceed beyond a WARNING or CAUTION notice until you have understood the hazardous condi tion and have taken appropriate steps Ne continuez pas avant d avoir pris connaissance du danger et prendre les mesures appropri es PAGE 2 DOC1203B REV 06 13 INSTALLATION INSTRUCTIONS IED GLOBALCOM IED1112PS SAFETY CONSIDERATIONS SAFETY PRECAUTIONS Personnel properly qualified in the applicati
16. nt The ground wire should be protected from mechanical damage and periodically inspected for good physi cal condition DOC1203B REV 06 13 INSTALLATION INSTRUCTIONS IED GLOBALCOM IED1112PS Personnel should never depend on a switch to remove power from equipment If the equipment is connect ed to the secondary distribution system by means of a power cable detach the cable from the receptacle before attempting any repairs of removal of chassis If the equipment is permanently wired to the secondary distribution system remove the main fuses or open the power switch Attach a suitable warning tag to the switch which will warn personnel not to operate the equipment only the person who originally attaches the warning tag should be authorized to remove it RESUSCITATION Personnel working with or near high voltage should be familiar with modern methods of resuscitation Such information and training is available from the Red Cross or local emergency response personnel such as the police and fire departments DESCRIPTION The 1112PS is a rack mount power supply designed to provide 12V DC power to GLOBALCOM devices The 1112PS ships with a single 1112PSM power supply module capable of delivering up to 37 Amps of 12V DC power to as many as eight 8 GLOBALCOM devices This allows a single power supply to power multiple 1100ACS 1200ACS 1100MSG 200MSG and 1300CNB units Each unit is connected to a fused power output port on the rear of the 1
17. on and use of life safety equipment qualified personnel shall read this manual carefully before performing any actions to specify apply install maintain and perform op erational tests of IED systems and associated products in accordance with the instructions in this manual This manual shall be made available to all qualified personnel who operate test maintain or service IED systems and associated products It is strongly recommend that such personnel read and understand the entire manual WARNING IF SAFETY PRECAUTIONS INSTALLATION AND TESTING ARE NOT PERFORMED PROP ERLY CONDITIONS COULD EXIST IN WHICH THE IED SYSTEM MAY NOT OPERATE OR MAY OPER ATE IMPROPERLY THIS COULD RESULT IN PROPERTY DAMAGE AND SERIOUS INJURY OR DEATH TO YOU AND OR OTHERS It is very important that only responsible trained personnel are allowed to operate and maintain these sys tems and that they use only appropriate equipment and tools If a person is not trained they shall contact the IED factory for direction on how to operate and maintain an IED system Unauthorized personnel and equipment must be restricted from the areas of operation All operations should be performed carefully methodically and without hurrying Greater effectiveness will be developed by increased familiarity of personnel with their assignments During any maintenance opera tion if a malfunction occurs or an incorrect indication appears stop the operation and determine whet
18. subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harm ful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Innovative Electronic Designs LLC 1 502 267 7436 phone wa se K 9701 Taylorsville Road 1 502 267 9070 fax gt ________ Louisville KY 40299 USA www iedaudio com Group REV 06 13 DOC1203B 2013 Innovative Electronic Designs LLC
Download Pdf Manuals
Related Search