HD089C2 User Manual
Contents
1. 0x87 720x480p Vf 60 Mode 7 pixelworks Setup Tab Seo sip sony gf ARN The setup tab allows the user to customize Picture in Picture as well as OSD settings Picture in Picture Picture in Picture settings Language Changes the language of the OSD Transparency Sets how visible the background of the OSD menu system OSD Timeout sets the length of time for the OSD to be displayed after the last keystroke Sleep Timer Sets how long the monitor will stay on with no video input Source Enable Enables or disables video Inputs Factory Reset Resets all user adjustments to factory defaults Advanced Tab Blue Gun Turns off red amp green channels for use when calibrating monitor False Color Displays colors representing different IRE Levels helps with setting correct exposure 2011 Manhattan LCD LLC All Rights Reserved Focus Assist Assists the operator achieve a fine focus on a desired object by adding white lines around objects that are in focus Color Bars Displays NTSC color bars on the screen helpful while calibrating Monochrome Displays the picture in black and white HDMI Video Color Space Changes the color space for the HDMI input HDMI ONLY Guides Tab Aspect Guides Displays lines on the screen which correspond to different aspect ratios Screen Markers Displays lines on the screen which correspond to different markers 2011 Manhattan LCD LLC All Rights Reserved Section Using Adv2. amp Cables B If you do not see a faint image then there may be a problem with the LVDS Settings or loose or broken LVDS Cable Solid White usually indicates a problem with the LVDS signal A Check the panel select See Section 1 2 amp 3 B Try a factory reset See Section1 1 2 amp 3 C Open up case and look for loose broken LVDS Cable between controller and LCD panel Section D Your monitor is not powering on 1 2 Plug the supplied 120 240V AC to 12V DC power supply into the monitor If the Red Status LED comes on go to Step 2 If it does not come on troubleshoot the power supply Our monitors use 12v regulated power either from the supplied power supply or from a battery pack With a volt meter make sure the power connector is showing 12V DC the center pin is positive the outer shell is negative If the power supply is good go to step 2 Open the monitor up and check inside for loose connections A Ifthe red power light is not coming on check the large cable that carries power from one side of the board to the other B Also check these pins for 12V and 5V C If red power light comes on and pressing the power button does not make the green led come on try removing the LVDS cable from the controller Section E Sending your monitor in for repair 1 If your monitor is new less than 2 weeks old it can be exchanged for a new one if available excluding clearance or refurbished items Have
3. was caused by use other than the normal intended purpose of the product Contact Manhattan LCD High Definition Monitors Contact Info John Reed Sales Engineering jrpeed manhattanlcd com Tel 407 247 8338 Vincent Falcone Tech Support Shipping vfalcone manhattanlicd com Tel 407 362 1818 Sales sales manhattanlcd com Support support manhattanlcd com Address Manhattan LCD 1007 Brielle Avenue Oviedo FL 32765 USA 15 2011 Manhattan LCD LLC All Rights Reserved
4. False Color can be viewed online www YouTube com ManhattanLCD 2011 Manhattan LCD LLC All Rights Reserved Focus Assist The focus assist function will allow users to focus the camera with great precision This feature is very similar to a peaking function on other brand monitors When enabled the object in focus will be highlighted in white and everything else will be darkened or grayed out To activate Focus Assist press MENU scroll to the Advanced Tab and turn the Focus Assist slider to the ON position hit MENU again to activate it To deactivate it follow the reverse procedure If you have a HDO89BV2 or HDO89CV2 you can assign a hotkey to this feature under the setup tab A video detailing how to use Focus Assist can be viewed online www YouTube com ManhattanLCD User Presets User presets are a useful tool when you are shooting with multiple camera rigs and want to use the Same monitor There are 3 user presets per input for a total of up to 15 user defined presets What you can do with each preset is set up the correct color and aspect ratio in the preset So next time you use that camera with the monitor all you need to do is choose the preset and you are ready to go Each preset will remember all of the settings inputted into the Picture tab and the image adjust tabs of the monitor To activate a preset select preset from the picture tab use the Left Right arrows to scroll through them and select the one you want A video
5. anced Features False Color False color is used for setting the correct exposure level or ISO setting on your camera It is important to use false color when you are shooting in low light and direct light situations because if your shot is severely under overexposed you may not have to re shoot an entire scene of your video This is how you use this feature To activate False Color press MENU scroll to the Advanced Tab and turn the False Color slider to the ON position hit MENU again to activate it To deactivate it follow the reverse procedure If you have a HDO89BV2 or HDO89CV2 you can assign a hotkey to this feature under the setup tab Completely underexposed or completely pitch black objects will be totally white 0 2 IRE The very dark shadows black colored objects and barely visible objects in shadows will be Blue amp Light Blue 2 20 IRE x mi 7 5 Lighter shadows amp dark colors such as a dark grey or a shadow on the side of a face or object will show up as Dark Grey amp Bright Purple 21 48 IRE Aay 10 03 35 4 The object of your video such as an object or persons face should be Medium Grey Green amp Light Grey 48 78 IRE Heavily lit areas ones where it appears to be in direct contact with light will display as Dark Yellow amp Yellow 78 84 IRE Overexposed areas ones which will appear white or near white in your video will display as Orange amp Red 85 108 IRE A video detailing how to use
6. assist you in correctly framing your shot Activating an Aspect Guide or Screen marker will display a rectangle box representing a specific aspect ratio For example if you are filming in 4 3 and you will be editing the video in post production 10 2011 Manhattan LCD LLC All Rights Reserved to 16 9 the aspect guides will show you if you will be cutting off the top of someone s head in the video Within the aspect guides you have several options for line style and safe Choosing a line style will allow you to select between a rectangle line black or partially grey bars in the inactive area Safe will allow you to make the aspect area smaller in 5 increments which will give you a safe area for the shot To activate a preset scroll to the Guides tab and select which screen marker you want to use To deactivate it follow the reverse procedure If you have a HDO89BV2 or HDO89CV2 you can assign a hotkey to this feature under the setup tab Section Power Options Our monitors may use any 12V regulated power source All monitors ship with a supplied 12V regulated AC adapter The input connector is a standard 2 1x5 5mm barrel connector the center pin being positive outer shell is negative You may use any power source as long as it is regulated If the polarity is reversed it will void your warranty if you overpower the monitor with a higher voltage than 12 5 volts it will blow a fuse and void the warranty We currently offer optional b
7. attery packs with Velcro strips for mounting amp battery plates for Panasonic Cannon amp Sony Batteries that include a built in power regulator to ensure proper operation The Battery plates are mounted to the monitor at the factory and are mounted in a sideways position to allow the monitor to be flipped upside down on cameras with 35mm lens adapters Note the green Status indicator it will turn on when the battery is charged and flash when the battery is low The power wire connects to the 12V dc jack when the monitor is being powered by the plate HDMI or Component or Composite connectors HD or SD Camcorder with Manhattan LOD HDOTTA Tekkeon MP 3450 External Battery 12V DC Ontinn sl rnare rnr a Pees MAN TE UE re HOMI Cable M M Met Included Section Basic Device Connectivity AC Power Option HDMI or Component or HO or SD Camcorder with Composite connectors Manhattan LCD HDOTIA 110V 220V AC 12V DC Wall Adapter Included Accessory HDMI Cable M M Not Included 11 2011 Manhattan LCD LLC All Rights Reserved Section Sun Hood Installation There are 8 treaded holes on the monitor 2 on each side the sun hood is a 2 piece design 1 piece fits on the top the second on the bottom they are made to fit on either side The sun hood mounts to the monitor with supplied thumbscrews in 2 easy steps 1 Thread in the thumbscrews about half way 2 Then slide the
8. cessible from inside the monitor there is no external connector Each input has its own set of menu items and are stored separately from each other adjusting an input will have no effect on another Picture Tab The adjustments you can make in the Picture Tab of the menu system are Preset Allows the user to make Preset color tables for different cameras Brightness Adjusts the amount of white in the picture Contrast Adjusts the contrast between the colors Phase Modifies the Clock Phase of the input VGA amp Component only Frequency Changes the frequency at which the panel is running VGA only Sharpness Adjusts the sharpness filter allowing you to go for a sharp look or smooth look Color Allows you to adjust the Color Saturation level Tint Allows you to adjust the Hue of the image Gamma Color Temp Allows you to adjust the Red Green and Blue channel gains individually Img Adj Tab The image Adjust tab will allow the user to adjust the images position and aspect ratio on the monitor Image Size Adjusts aspect ratio Fill All 1 1 Fill Aspect 4 3 16 10 15 9 16 9 1 85 1 2 35 1 Red Camera amp Canon 7D HDSLR Record amp HDSLR Playback H position Horizontal position of the picture V position Vertical position of the picture Overscan allows the operator to zoom in or out ona specific image Auto Auto centers the position the picture on the screen Freeze Frame Freezes a specific image on the screen
9. detailing how to use the Presets feature can be viewed online www YouTube com ManhattanLCD Image Size Feature The Image size feature will allow the user to select a specific aspect size such as 4 3 16 9 and 16 10 among others Our monitors have some camera specific modes for Cannon DSLR cameras and The Red Cameras which use a proprietary resolution different from the norm Fill to Aspect This is a very handy feature when shooting on most cameras It will allow you to let the monitor adjust the image to whatever aspect ratio you are filming HDSLR Record Mode This Mode will allow you to correctly view the image on a Canon DSLR camera such a 5D or T2i it will automatically switch the resolution between preview and record modes and will display the image in full screen HDSLR Playback Mode This Mode will allow you to correctly view the image on a Canon DSLR camera such a 5D or T2i it will automatically display the correct resolution when you play back a clip from the camera and will display the image in full screen 2011 Manhattan LCD LLC All Rights Reserved Red Camera Mode This Mode will allow you to correctly view the image on a Red Camera such as a Red One Red cameras use a proprietary resolution coming from their HDMI output that normally only worked with their brand of monitors Our Monitor can automatically adjust to their proprietary and display the image in full screen without cutting off the camera info A video d
10. e Version Hit MENU and check the date of the firmware If your firmware is before July 6 2010 there are some known issues with the HDMI using newer cameras You can get a firmware upgrade kit from our online store 3 Check the input cables for loose or reversed connections If they check out try displaying an image from a DVD player using the same cables If there is no signal from a DVD player try a different signal cable 4 Ifthe DVD player amp cable works there may be something wrong with the cameras output signal A Composite and Component require 1V to operate properly Check with a volt meter or oscilloscope B If you are using HDMI make sure the HDMI cable is a certified 1 1 or higher 5 Ifthe DVD player does not work first check with another set of cables If it still does not show an image the monitor may have a loose connection or bad connector A HDMI Open the monitor up there are 2 HDMI ports on the controller check both HDMI inputs You can plug a HDMI cord into either one of the HDMI Ports directly If you have an HD5 HDO71A both HDMI ports are accessible from the outside If neither works there may be something wrong with the controller board send it in for repair B Component Composite none of the PW338 based monitors support sync on green do not plug the yellow Composite video into the Green Y port on the monitor it will not work Use the yellow composite connector With the component connector the Y signal is the m
11. etailing how to use the Image Size feature can be viewed online www YouTube com ManhattanLCD Blue Gun Calibrating This feature will allow you to calibrate the monitor to your particular camera by only allowing the monitor to display information from the blue channel of the standard RGB color scheme There are many ways to accomplish this task and the monitor is usually very close to perfect right out of the box so usually only minor adjustments are required Please follow these steps 1 Send the Monitor SMTP Color Bars from the Camera or signal generator Picture To Right 2 Activate the Blue Gun feature of the monitor Press MENU scroll to the Advanced Tab and turn the Blue Gun slider to the ON position hit MENU again to activate it If you have a HDO89BV2 or HDO89CV2 you can assign a hotkey to this feature under the setup tab 3 Use the menu system or Quick Access Button on remote to set Brightness Up Down until the plunge bar is displayed correctly It will be correct when only 1 grey bar is visible Left Picture Below 4 Set the Color Up Down until the far Left Right blue columns are the same color Middle Picture Below 5 Set the Tint Hue Up Down until the middle Left Right blue columns are the same color Right Picture Below A video detailing how to use the Blue Gun feature can be viewed online www YouTube com ManhattanLCD Aspect Guides amp Screen Markers The Aspect Guides and Screen Markers Features will
12. groves in the sun hood around the shaft of the thumbscrews and Snug the thumbscrews 12 2011 Manhattan LCD LLC All Rights Reserved Section Advanced Troubleshooting Section A Your monitor turns on but the screen is locked up or non responsive 1 Make sure the monitor is powered off press and hold the Up amp Down arrows Press Power and hold all 3 for 5 seconds This clears NV Ram and sets the controller to Factory default settings 2 HDO89BX HDO71AX skip this step all others press and hold Menu and Input press and release Up Arrow until you see something on the screen 3 Verify settings are correct press 9 1 1 MENU on remote and go to factory menu to setup the controller for your model monitor HDO89B HDO71A panel select 000 keypad amp HDMI Rename is 000 HDO89B2 HDO71V2 panel select 000 keypad amp HDMI Rename is 001 HDO89C panel select 001 keypad amp HDMI Rename is 000 HDO89C2 panel select 004 keypad amp HDMI Rename is 001 HD5 panel select 002 keypad amp HDMI Rename is 000 4 If your monitor continues to have trouble it may be in need of a firmware upgrade or repairs Please contact Manhattan LCD support support manhattanlcd com Section B Your monitor turns on but stays on a blue screen 1 Verify the monitor is on the correct input On the monitors control panel press INPUT button and use the Up amp Down arrows to scroll to the selected input and hit INPUT again to select 2 Check the Firmwar
13. maiCakt Wer lA T EJN Dh eer Ll OORS ah A CON COLOR TINT Fa amp HD089C2 User Manual Updated 9 20 2011 Contents Page 1 Contents Page 2 3 Features amp Specifications Page 4 Remote Control Page 5 7 Basic Monitor Adjustments Page 8 11 Using Advanced Options Page 11 Power Options Page 12 Sun Hood Installation Page 13 14 Advanced Troubleshooting Page 15 Warranty 2011 Manhattan LCD LLC All Rights Reserved Section Features amp Specifications LCD Screen Specifications Screen Size 8 9 Diagonal Screen Architecture WXGA HD 720p Native 1280X768 Pixels Screen Backlight Edge Lit LED Contrast Ratio 500 1 Brightness 400 nits Viewing Angle LR UD 110 100 Screen Finish Crystal Clear Gloss Video Inputs HDMI 1 Input VGA 1 Input Component 1 Input Composite Video 1 Input 3G HDSDI 1 Input Optional Controller Specifications Accepts HD Video Up to 1080P 60Hz NTSC amp PAL Compatible HDCP Compliant Firmware Upgradable Compatible Frame Rates 24Hz 50Hz 60Hz Supported resolutions 1080p 1080i 720p 576p 576i 480p 480i Power 12v DC requires Regulated power supply Power Consumption 1300 MA 12V DC Software Features Screen Markers amp Aspect Guides Focus Assist 2D peaking False Color exposure assist Under scan Over scan Canon DSLR Record amp Playback Mode EOS 5D 7D 60D Red Ca
14. mera Mode For Use with Red Cameras HDMI Port Adjustable Color Control Adjustable Aspect adjustments Color Table Presets Picture in Picture 2011 Manhattan LCD LLC All Rights Reserved Case Specifications 19 button Keypad with aluminum buttons 2 standard 1 4x20 mounts Top amp Bottom Case 0 125 thick Black ABS Polymer Matte Finish Case Dimensions 9 2 Wide 6 9 High 1 4 Deep Weight Approx 1 9 LBS Optional Accessories 3G HDSDI w Loop through ABS Sun hood Sony Battery Plate Canon Battery Plate Panasonic Battery Plate Anton Bauer Battery Plate XLR Power Input w built in voltage regulator 2011 Manhattan LCD LLC All Rights Reserved Section Remote Control Mute Sound OSD Sleep Direct Channel Selection amp Programing Volume Control Image Size Picture Mode l Audio Mode Signal Input Selector The remote requires 2 AAA batteries not included Sections Highlighted in Red are new features added 4 1 2010 Infrared LED Invisible Power ON OFF Picture In Picture Picture By Picture swap frames Freeze Frame Channel Selection OSD Menu Menu Navigation Array scroll Up or Down Left or Right Enter selection Quick access menu appears on the lower right side of the screen Use the recall button to go up a menu level in the quick menu NOTE The remote is required to access the quick menu amp Factory Menu if you need to access the factory menu you mu
15. ost important If the y green plug is plugged in you should see a monochrome image the Pb amp Pr carry the color information reversing them will inverse the blue and red colors on the image make sure they all carry around 1V with a volt meter 13 2011 Manhattan LCD LLC All Rights Reserved C 3G HDSDI On certain model monitors there is an option for 3G HDSDI The SDI signal requires a 75 OHM coax cable If you are unable to see a signal from your camera using SDI check the cable first The SDI status light should be solid green when it is receiving a signal and flash when there is no signal If the status light does not light up at all the power connector inside the monitor that goes to the 3G board may have come loose If the status led is solid green but no video the HDMI adapter plug may have come loose from the controller you may need to open the case and check the connections D VGA there are a few cameras on the market with VGA out You can check the monitor with a computer just attach the other end of the cable to a laptop or desktop computer and enable the computer s VGA Port Section C Your monitor turns on but the screen is solid black or solid white 1 Solid Black Usually indicates a bad connection with the backlight ballast Or a bad backlight inverter or bad LCD panel A Power on monitor in a well lit area press menu if you can see the menu but very faint then backlight is not working Troubleshoot the LED Driver
16. st contact the support department support manhattanlicd com 2011 Manhattan LCD LLC All Rights Reserved Section Basic Monitor Adjustments Powering on the Monitor Insert 12V regulated power source via connector into the 12V DC socket A RED LED will indicate power is reaching the monitor If RED LED fails to light trouble shoot the power adapter or battery The screen will be BLACK until you press the POWER button on the monitor or the remote When the monitor is powered on the LED status indicator should be green and the monitor will display the Manhattan LCD logo for 1 second and then switch to a solid blue screen May display a black screen on certain firmware revisions Selecting an Input Power ON OFF Using the Control console located on the left Scroll Up side of the monitor press the INPUT button Scroll Down Use the v buttons located just under the Scroll Right POWER button and scroll to the appropriate Scroll Left input Press the INPUT button to select and Menu OSD activate the input Source Select Using the remote control unit with two AAA batteries installed point the remote at the Monitor Console s IR port beneath LED indicator and press the Source Button use the Up amp Down arrows to scroll to the appropriate input and the enter key to select the input Navigating the menu system NOTE you must be on an input that is receiving a video signal to make any changes to any options Using the Con
17. trol console located on the left side of the monitor press the Menu button To scroll between Picture Img Adj amp Setup tabs use the gt lt buttons located above the MENU key Use the v buttons located just under the POWER button to scroll within a menu tab To adjust a specific field use the gt lt buttons located above the MENU key to apply your changes and go up a level press the MENU button again to save your changes and go up a level and MENU button once more to exit the menu Using the I R remote control unit with two AAA batteries installed point the remote at the Monitor Console s IR port beneath LED indicator and press the MENU Button use the up amp down arrows to scroll to the appropriate input and the enter key to select the input To scroll between Picture Img Adj amp Setup tabs use the Left amp Right arrow buttons located under the MENU key Use the Up amp Down arrow buttons located just under the Menu button to scroll within a menu tab To adjust a specific field use the Left amp Right arrow buttons located below the MENU key to make changes to a certain field Press the MENU button again to save your changes and go up a level Use the UP arrow to get back to the menu tabs and MENU button once more to exit the menu 2011 Manhattan LCD LLC All Rights Reserved These monitors are equipped with 4 external inputs VGA Component Composite and HDMI port The HDO89B model has a second HDMI port which is only ac
18. your Manhattan LCD order number or retail invoice ready and send us an email Support manhattanicd com or call us 407 362 1818 If your monitor is covered under warranty but older than 2 weeks is a clearance or refurbished item we will repair your monitor free of charge just contact us for an RMA Have your order number or invoice handy 14 2011 Manhattan LCD LLC All Rights Reserved 3 If your monitor is out of warranty you can repair it yourself with parts available on our website or we Can repair it for you All applicable parts labor amp return shipping charges will apply Section Warranty Statement Warranty Manhattan LCD monitors are under warrantee and are guaranteed to be free from manufacturing defects for a period of 12 Months from the date of purchase to the original owner unless otherwise specified Disclaimers Manhattan LCD Shall be indemnified and held harmless for any and all injury or death resulting from the improper use of their products Warranty is null and void if there is any evidence of tampering or abuse or if the case has been opened or modified in any way unless otherwise specified Claims Claims for damages must be preceded by a Return Merchandise Authorization RMA RMA s may be requested directly from the manufacturer or authorized distributors Manhattan LCD reserves the right to refuse to repair or replace any monitor that it deems is in need of repair due to customer negligence or damage
Download Pdf Manuals
Related Search