CAT-2 / CAT-2-TA - Drucksysteme Janz & Raschke GmbH
Contents
1. MAINTENANCE Your CAT 2 requires no maintenance Product Limited Warranty All Labelmate Products are warranted to the original end user customer to be free from defects in materials and workmanship If it is determined by Labelmate that a product has failed under the terms of this warranty the product will be repaired or replaced at no charge to the customer Labelmate reserves all rights to determination of coverage and liability under this warranty The warranty period for all new Labelmate products is outlined below Warranty Period Products Covered Label Rewinders ayeas Label Unwinders Label Counters mechanical parts only Label Slitters mechanical parts only Label Dispensers Printer Mechanisms Power Supply Modules Counter modules Encoders Any products not specified above The warranty period for all products starts on the date purchased by the original end user customer Warranty coverage is not transferable with ownership and will terminate immediately upon rental resale or any other change in ownership This warranty does not cover repair to any product which is damaged has been modified is missing parts or has been opened or repaired by any unauthorised person Use of any unauthorised accessory or attachment will void coverage Purchase documentation should be retained for coverage verification In the event your product requires service please contact the distributor you bought the product from The cust2. he Rewinder Drive Unit case Tighten the Allen Screw onto the flat part of the Motor Shaft until it is tight Set the CAT 2 in place near the label exit slot of the printer CAUTION AVOID ACCIDENTS THE CAT 2 WEIGHS OVER 11KG 24Lb SO CHOOSE ONLY A STURDY SURFACE ON WHICH TO SET THE UNIT Verify that the DIRECTION Switch on the CAT 2 Control Panel is in the OFF position Plug the Power Plug at the end of the wire on the AC Wall Transformer into the CAT 2 Power Input Jack Plug the AC Transformer into an appropriate AC power outlet The unit is now ready for use A WARNING This Product is for indoor use only Not for use in wet locations LABEL REWINDING Place the DIRECTION Switch on the CAT 2 Control Panel in the centre OFF position 2 Slide an empty label core over the Quick Chuck or Vanes on the shaft until the core is against the inner Flange Plate On the Quick Chuck tighten the Lock Knob for an ACH see the ACH user manual 3 If desired slide the outer label Flange Plate with Ball Plunger in the Hub onto the Shaft and up against the label core 4 For CAT 2 TA see TA Manual Feed the label web from the printer and secure it to the take up roll core with tape Rotate the take up reel a couple of turns For CAT 2 TA see TA Manual 5 Place the CAT 2 TORQUE RANGE Switch in the NORMAL REWIND position NOTE When the TORQUE RANGE Switch is in the HIGH SLIT position the CAT 2 develops h
3. igher torque Use the HIGH SLIT position for label slitting or rewinding large diameter rolls 6 Rotate the TORQUE Control Know to the minimum postion fully counter clockwise Place the CAT 2 DIRECTION Switch in the position desired to run left or right Start the printer and adjust the TORQUE Control Knob for the desired take up tension Use the minimum TORQUE setting needed to rewind labels properly Excessive torque might pull the labels too hard and cause the printer to lose registration EXTERNAL HALT CONTROL An External Halt Control jack on the CAT 2 is for use with external devices capable of providing an open circuit halt command A 3 5mm control cable is necessary for use not included With Pin 2 and Pin 3 of the External Halt Control circuit closed connected together using a 3 5mm dual circuit plug the CAT 2 will operate When the External Circuit is opened the CAT 2 will stop 3 5mm EXTERNAL HALT CONTROL Plug Dual Circuit Plug Contact CLOSED RUN Contact OPEN HALT Pin 1 No connection NOT USED Pin 2 Normally Closed NC contact Pin 3 Normally Closed NC contact return 12V EXT HALT CONT 40 3 5 mm Jack D w en 1K C ve Dual Circuit 10K S Va fo 2 ae V Vv
4. nly Tension Arm with setscrew and Shaft Screw e Two 300mm 12 Plastic Flange Plates One only for QC none for ACH Retain the Shipping Container and Packaging for Storage and Transport e KEEP MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE e Tel 49 0 40 840 509 0 Fax 49 0 40 840 509 29 www jrdrucksysteme de SPECIFICATIONS Max Label Roll Weight 7Kg 15 4Lb for Standard 15Kg 33Lb for QC 6Kg 13 2Lb for ACH Max Label Roll Size 300mm 12 diameter 280mm 11 for ACH Power Supply CAT 2 Input 220 240VAC 50 60Hz Output 11 VAC 2 5A CAT 2 TA 220 240VAC 50 60Hz Output 15VAC 4 6A SET UP CAT 2 TA First install the tension arm referring to the enclosed TA User Manual 4 you have the ACH Adjustable Core Holder option Skip to step 4 STANDARD AND 10 Identify the inner Label Flange Slide the Flange Plate onto the hollow end of the Rewind Shaft For maximum width the Flange face should be flush with the end of the Shaft Tighten the screw in the Hub until it is snug Not too tight CHUCK Mount the inner Flange onto the Quick Chuck with two screws provided Slide the Shaft and Flange Assembly onto the CAT 2 Motor Shaft allowing for clearance to the CAT 2 Chassis and Motor Screws Tighten the Allen Screw onto the flat part of the Motor Shaft until it is tight ACH Slide the Hub of the ACH over the motor Shaft of the CAT 2 Position the Hub so there is a gap between the ACH Hub and t
5. omer assumes responsibility for all cost and risk incurred in transport for service Labelmate makes no other warranty of any kind expressed or implied or to suitability or fitness for a particular purpose No other person agent or reseller is authorised to give any warranties on behalf of Labelmate Any obligation to warranty other than that specifically addressed above is hereby disclaimed LABELMATE LLC 69 AVENUE ALPHONSE XIII 1180 BRUSSELS BELGIUM TEL 322 375 69 60 FAX 322 375 38 96 brussels labelmate com www labelmate com LABELMATE User_CAT 2 02 07 Drucksysteme Janz amp Raschke GmbH Osterbrooksweg 71 D 22869 Schenefeld Email kontakt jrdrucksysteme de CAT 2 CAT 2 TA Heavy Duty CAT Label Rewinder e Dual Torque Range and Direction Controls e Constant Adjustable Torque CAT technology e Adjustable Speed Control up to 760mm 30 per second e Precise Variable Torque Control CAT 2 ACH e On demand Rewinding Turns Off when Labels Stop Coming from Your Printer TA only CAT 2 TA STANDARD Remove all parts from the shipping container and verify contents Package Contents e User Manual this document e CAT 2 Drive Unit e Power Supply Module e LABELMATE Quick Chuck Quick Locking Core Chuck or Standard Shaft with three 3 metal Vanes installed or Model 10 INCHES Shaft with six 6 metal Vanes installed or Model ACH Adjustable Core Holder e CAT 2 TA o
Download Pdf Manuals
Related Search