User Manual - CompSource.com
Contents
1. POWER SWITCH Start Your Installation Please follow these instructions so that you can hookup the cables to associated connector T pn Lay the display flat on an even surface 2 Move the stand into position as seen in the step 2 diagram 3 4 Connect the cables to the appropriate connectors as seen in the step 4 diagram Use Remove the cable cover as seen in the step 3 diagram step 4 1 diagram if using the RS 232 serial connector Use the step 4 2 diagram if using the USB connector Position all cables under the cover lip as seen in the step 5 diagram Re attach the cable cover Remove the screw CBM M3x6 from the accessory box and insert the screw into the cable cover and monitor as seen in the step 5 diagram Connecting the Display Figure 8 1 To setup this display please refer to the following figure and procedures 1 Be sure all equipment is turned off 2 Connect the AC power cord to the power connector on the monitor and the other end into an electrical outlet 8 1 3 Connect the D SUB cable from the display s VGA input connector to the D SUB connector of your host computer and tighten the screws 8 1 4 Connector the audio in cable from the audio input port of your display to the audio out port of your computer 8 1 5 Connect the RS 232 or USB cable from the RS 232 or USB port of y2. 1 Power on the computer 2 Make sure that the RS232 or USB cable is connected to the computer 3 Be sure that your EWF is disabled If your EWF is enabled please disable the EWF by using the EWF Manager command 4 Once the EWF is disabled click on the XP driver at www planar com support and follow the step by step instructions as shown on the pop up windows Custom 1 Power on the computer 2 Make sure that the RS232 or USB cable is connected to the computer 3 Follow the step by step instructions found in the zipped file at www planar com support If you are using a PC running Windows CE follow the instructions below 1 Power on the computer 2 Make sure that the RS232 or USB cable is connected to the computer 3 Using Platform Builder build an image file by following the step by step instructions found in the zipped file at www planar com support If you are using a PC running Linux or Apple Mac OS follow the instructions below 1 Power on the computer 2 Make sure that the RS232 or USB cable is connected to the computer 3 Follow the step by step instructions found in the zipped file at www planar com support When changing the Touch Interface RS 232 or USB please follow instructions below 1 Uninstall the touch driver Re start the computer Remove the original Touch Interface RS 232 or USB Connect the computer to the Touch Interface RS 232 or USB that you would like to use Install t
3. Apple Mac Resolution 720 x 400 640 x 480 640 x 480 640 x 480 800 x 600 800 x 600 800 x 600 800 x 600 1024 x 768 1024 x 768 1024 x 768 640 x 480 832 x 624 H Frequency KHz 31 47 31 47 37 86 37 50 35 16 37 88 48 08 46 88 48 36 06 48 60 02 35 00 49 72 V Frequency Hz 70 60 72 75 56 60 2 75 60 70 75 66 75 Touch Screen Driver Installation The PT1545R is available with both RS232 and USB connections The touch driver is located at www planar com support for these operating systems Windows 7 8 VISTA XP 2000 ME 98 NT 4 0 CE XP Embedded Linux kernel 2 6 x 32 bit amp 64 bit Apple Mac OS The PT1545P is available with USB connection The touch driver is available at www planar com support for these operating systems Windows 7 8 VISTA XP 2000 CE XP Embedded Linux kernel 2 6 x 32 bit amp 64 bit Apple Mac OS Windows 7 8 Multi touch without driver Please Note 1 The PT1545R PT1545P is Microsoft Windows HID Human Interface Device compatible if you use the USB touch screen interface No additional software driver is required for general operation of the touch screen A calibration tool can be installed for improved touch position accuracy See Optional Calibration Tool Install section for more information 2 For PT1545P the system requires 15 seconds for Windows 7 8 to process the touch program while turning power on off o
4. EE 15 _ _ gt 9 9 9 9 9 92 9 22 16 16 9 3 _ _ _ 3322 3 __ 16 gt gt gt gt gt gt gt V MC 16 _ _22222 2 3 2 333_ _ _ 17 L kk E EEA TA 17 2 22 222 22 22 _ 18 Rail 19 Touch Screen Driver EE te EEN 20 PT1545R Optional Calibration Tool install eee 20 PT1545P Optional Calibration Tool ut UE 21 PTR Msta Irenee L 23 PT TS49P ah lere Tas EEN 25 CTW Eae EE 26 Usage Notice Warning To prevent the risk of fire or shock hazards do not expose this product to rain or moisture Warning Please do not open or disassemble the product as this may cause electric shock Precautions Follow all warnings precautions and maintenance as recommended in this user s manual to maximize the life of your unit Do e Tim off the product before cleaning e Touch screen surface may be cleaned using a soft clean cloth moistened with mild window glass commercial cleaners or 50 50 mixture of water and isopr
5. PLANAR PT1545R PT1545P Touch Screen Monitor USER S GUIDE www planar com The information contained in this document is subject to change without notice This document contains proprietary information that is protected by copyright All rights are reserved No part of this document may be reproduced translated to another language or stored in a retrieval system or transmitted by any means electronic mechanical photocopying recording or otherwise without prior written permission Windows is a registered trademark of Microsoft Inc Other brand or product names are trademarks of their respective holders The test results show that this device meets the FCC rules Those limits are set to protect residential areas from the devices with harmful emission This device will produce use and radiate radio frequency energy In addition failure to follow the user s manual to install or use this device might produce harmful interference with radio communication Not withstanding the foregoing it does not guarantee that this type of harmful interference does not occur in some special installations The interference caused by this device to the reception of radio or television signals may be verified by turning it on and off Any changes or modifications to this TFT LCD would void the user s authority to operate this device Important Recycle Instructions Lamp s inside this product contains mercury This product may contain other elec
6. are the three kinds of Warning Signal Please check the cable connections or contact your local dealer or Planar for more information No Signal This message means that the display has been powered on but it cannot receive any signal from the computer graphics card Check all the power switches power cables and VGA sig nal cable Going to Sleep The display is under the power saving mode In addition the display will enter power saving mode when experiencing a sudden signal disconnecting problem The monitor can be activated by pressing any key on the keyboard triggering the mouse or touching the screen Out of Range This message means that the signal of the computer graphic card is not compatible with the display When the signal is not included in the Video Modes list we have listed in the Ap pendices of this manual the monitor will display this message Product Dimensions PT1545R 8 350 8 mm 8 gt Front View c C C wi LOD NS I Side View A C X 67 0 mm 222 5mm gt Top View 202 0 mm PT1545P Front View Side View 196 1 mm gt Top View 202 0 mm Compatibility Modes Mode IBM VGA IBM VGA VESA VGA VESA VGA VESA SVGA VESA SVGA VESA SVGA VESA SVGA VESA XGA VESA XGA VESA XGA Apple Mac Il
7. d Windows Media Center Calculator Sticky Notes Snipping Tool Solitaire Magnifier a Remote Desktop Connection Ki d Microsoft Surface Collage gt AI Programs Adjust your computer s settings System and Security Review your computer s status Back up your computer Find and fix problems Network and Internet View network status and tasks Choose homearoup and shari Hardware and Sound View devices and printer ee eee Hardware and Sound Add or remove printers lt hardwa pertge system sounds play CDs automatically conserve Uninstall a program power update device drivers and f more Pe test Documents Pictures Music Games Computer Control Panel E Devices and Printers Default Programs Help and Support View by Catego User Accounts and Family Safety DN Add or remove user accounts DN Set up parental controls for any user Appearance and Personalization Change the theme Change desktop background Adjust screen resolution Clock Language and Region Change keyboards or other input methods Change display language Ease of Access Let Windows suggest settings Optimize visual display Hardware and Sound gt _ Devices and Printers Adda device Adda printer Mouse Device Manager AutoPlay Change default settings for media or devices Play CDs or other media automatically Sound Adjust system volume Change system sounds Mana
8. file at www planar com support If you are using a PC running Windows CE follow the instructions below 1 Power on the computer 2 Make sure that the USB cable is connected to the computer 3 Using Platform Builder build an image file by following the step by step instructions found in the zipped file at www planar com support If you are using a PC running Linux or Apple Mac OS follow the instructions below 1 Power on the computer 2 Make sure that the USB cable is connected to the computer 3 Follow the step by step instructions found in the zipped file at www planar com support Technical Support Cables and Accessories To find cables and accessories for your Planar monitor touch screen or other Planar products visit our online store at www PlanarOnline com Technical Support Visit Planar at http www planar com support for operations manuals touch screen drivers warranty information and access to Planar s Technical Library for online troubleshooting To speak with Planar Customer Support please have you model and serial number available and dial Planar Support Tel 1 866 PLANAR1 866 752 6271 or 1 503 748 5799 outside the US Hours 24 hours a day 7 days a week Toll or long distance charges may apply Planar Systems Inc Customer Service 24x7 Online Technical Support http Awww planar com support 1195 NW Compton Drive Beaverton OR 97006 1992 Tel 1 866 PLANAR1 866 752 6271
9. ge audio devices Power Options Change power saving settings Change what the power buttons do Require a password when the computer wakes Change when the computer sleeps Choose a power pla Display Make text and other items larger or smaller Adjust screen resolution Connect to an external display How to correct monitor flicker refresh rate Pen and Touch Change tablet pen sett Turn flicks on and off Set flicks to TTT Tablet PC Settings Configures tablet and screen settings for a Tablet PC Configure Configure your pen and touch displays Display options Display 1 Display device on VGA GG Details Touch Input Available Choose the order Go to Orientation PT1545R Install Instructions If you are using a PC running Windows 7 8 VISTA XP 2000 ME 98 NT4 0 follow the instructions below 1 Power on the PC 2 Be sure the USB or the RS 232 Serial cable is connected from the PC to the display 3 Visit www planar com support 4 Follow the step by step instructions as shown on the pop up windows If you are using a PC running driver Linux kernel 2 6 x 32 bit amp 64 bit follow the instructions below 1 Power on the PC 2 Be sure the USB cable is connected from the PC to the display 3 Visit www planar com support 4 Follow the step by step instructions as shown on the pop up windows If you are using a PC running Windows XP Embedded follow the instructions below Express
10. he Touch driver then follow the step by step instructions as show on monitor E PLEASE NOTE Don t plug in both the RS 232 and USB cables Doing so may cause a driver conflict making your touch screen inoperable PT1545P Install Instructions If you are using a PC running Windows 7 8 VISTA XP 2000 follow the instructions below 1 Power on the PC 2 Make sure that the USB cable is connected to the computer 3 Visit www planar com support 4 Follow the step by step instructions as shown on the pop up windows If you are using a PC running driver Linux kernel 2 6 x 32 bit amp 64 bit follow the instructions below 1 Power on the PC 2 Make sure that the USB cable is connected to the computer 3 Visit www planar com support 4 Follow the step by step instructions as shown on the pop up windows If you are using a PC running Windows XP Embedded follow the instructions below Express 1 Power on the computer 2 Make sure that the USB cable is connected to the computer 3 Be sure that your EWF is disabled If your EWF is enabled please disable the EWF by using the EWF Manager command 4 Once the EWF is disabled click on the XP driver at www planar com support and follow the step by step instructions as shown on the pop up windows Custom 1 Power on the computer 2 Make sure that the USB cable is connected to the computer 3 Follow the step by step instructions found in the zipped
11. lus input e Surface Anti glare treatment Interface Dual RS 232 Serial USB controller Transmittance 82 5 e HID Windows 7 8 e Driver Windows 7 8 VISTA XP 2000 ME 98 NT 4 0 CE XP Embedded Linux kernel 2 6 x 32 bit amp 64 bit Apple Mac OS Touch Screen for PT1545P Projected Capactive touch screen for finger input only e Surface Glare treatment Interface USB controller Transmittance 90 5 e HID Windows 7 8 Driver VISTA XP 2000 CE XP Embedded Linux kernel 2 6 x 32 bit amp 64 bit Apple Mac OS Package Overview Lg Den LCD Display USB Cable A to B Cable Cover Screw Power Cord RS 232 Cable PT1545R only PLANAR When Image Experience Matters Landing Strip VGA Signal Cable Audio in Cable PLA PLANAR ter Lu ee ZZ USER S GUIDE WW wm Planariouch Installation Product Overview e Front View e PT1545R Bottom View Without Stand AUDIO AC IN RS 232 T USB A LO Vee ees ll IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII III IIIIIII POWER SWITCH e PT1545P Bottom View Without Stand
12. n button is released the previous setting will be saved and exit the Lock Unlock menu automatically Please note a When the OSD Lock function is selected this indicates that all the buttons except power button are now disabled b When the Power Lock function is selected this indicates that the power key is disabled user can not to turn off the monitor by Power key J On Screen Display Menus Main OSD Menu ITEM Contrast Brightness Auto Adjust Left Right Up Down Horizontal size Fine OSD Left Right OSD Up Down OSD Time out OSD Language Factory Reset RGB Volume Mute CONTENT The monitor luminance level control The monitor backlight level control Fine tune the image to full screen automatically Moving screen image horizontal position to left or right Moving screen image vertical position to up or down The screen image horizontal dot clock adjustment The screen image pixel phase adjustment Moving OSD menu horizontal position to left or right Moving OSD menu vertical position to up or down OSD auto disappear time selection OSD menu language selection English French Japanese Deutsch Spanish Italian Traditional Chinese and Simplified Chinese Factory default value restored Color temperature selection 9300K 6500K 5500K 7500K User Audio volume adjustment Audio On Off control Appendix Troubleshooting II you are experiencing trouble with the displa
13. opyl alcohol e Use a soft cloth moistened with mild detergent to clean the display housing e Disconnect the power plug from AC outlet if the product is not going to be used for an extended period of time Don t e Do not touch the LCD Display screen surface with sharp or hard objects e Do not use abrasive cleaners waxes or solvents for your cleaning e Do not operate the product under the following conditions Extremely hot cold or humid environment Areas susceptible to excessive dust and dirt Near any appliance generating a strong magnetic field In direct sunlight Introduction About PT1545R PT1545P The PT1545R PT1545P is a 15 flat panel screen with an active matrix thin film transistor TFT liquid crystal display LCD This unit is to be used as commercial and light industrial equipment only Features include Direct Analog signal input Active matrix TFT LCD technology 1024 x 768 XGA resolution 15 viewable display area 31 5 60 KHz horizontal scan 56 75 Hz high refresh rate 0 297mm x 0 297mm pixel pitch Auto adjustment function Multilingual OSD user control Kensington security slot 100 mm VESA mount Removable base for flexible mounting solutions PT1545R 5 wire resistive touch screen with dual RS 232 Serial USB controller PT1545P Projected Capactive touch screen with USB controller Build in audio 1W x 2 Touch Screen for PT1545R e 5 wire resistive touch screen for finger and sty
14. or 1 503 748 5799 outside the United States Hours 24 hours a day 7 days a week 2013 Planar Systems Inc 10 13 Planar is a registered trademark of Planar Systems Inc Other brands and names are the property of their respective owners Technical information in this document is subject to change without notice 020 1020 00E 820450065105
15. ors and corresponding with the standards of flat panel monitor mounting devices such as wall and table arms The VESA mounting interface is located on the back of your monitor To mount the monitor on an UL listed swing arm or other mounting fixture follow the instructions included with the mounting fixture to be used Slots x4 VESA Mounting Interface A Warning Please select the proper screws The distance between the back cover surface and the bottom of the screw hole is 11 mm Please use four M4 screws diameter with proper length to mount your monitor Please note the mounting stand must be able to support at least 11 Ibs 5Kg Remove the Deskstand Remove 4 screws and then remove hinge User Controls Side Panel Controls E Menu A Up Down 41 Enter men Ai Power Menu appear appear Menu Menu disappear retum to main item return to main item SC Brightness Main item select up Adjust up Main item select down Adjust down Enter Select sub item function Power On Off How to Use the OSD Menus J Koy Name E Menu A Up Y Down 4 Enter Power 1 Press the MENU button to pop up the on screen menu and press Up or Down button to select among the six functions in the main menu 2 Choose the adjustment items by pressing the Enter but
16. our display to the RS 232 port or USB port 8 1 of your computer 6 Configure the touch screen Refer to the Touch Screen Driver Installation section on page 20 7 Once the touch screen is configured the monitor is ready for use AN Notice To ensure the display works well with your computer please configure the display mode of your graphics card to make it less than or equal to 1024 x 768 resolution and make sure the timing of the display mode is compatible with the display We have listed the compatible Video Modes of your display in the appendix on page 19 for your reference Figure 8 1 PT1545R PT1545P I a Kensington Security Slot The monitor can be secured to your desk or any other fixed object with Kensington lock security products The Kensington lock is not included A Kensington Security Slot VESA Mount Your Monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface standard which defines a physical mounting interface for flat panel monit
17. r plugging unplugging USB cable PT1545R Optional Calibration Tool Install II you would like to use the Optional Calibration Tool follow the instructions below Please note the calibration tool supports Windows 7 8 VISTA XP XP Embedded 2000 98 and ME operating systems via USB only Visit www planar com support Select the model name part number and operating system Click on Calibration Utility The HID calibration tool will automatically open From here the user can choose to do the following oy gt a 4 Points Calibration b 9 Points Linearization c 25 Points Linearization d Clear e Draw Test f Advanced In the Advanced settings area the user may do the following I Adjust the Double Click Area ll Enable auto right click and adjust the auto right click time ili Choose to be either in the HID Mouse Mode or HID Digitizer Mode Windows 7 8 Vista iv Simply click the Apply button once the settings are finalized PT1545P Optional Calibration Tool Install Calibrating the touch screen in Windows 7 8 1 2 3 Tap the Start button Control Panel and then Hardware and Sound Under Tablet PC Settings tap Calibrate the screen for pen or touch input On the Display tab under Display options tap Calibrate and then Yes to allow the program to make changes Follow the on screen instructions to calibrate the touch screen eGalaxTuner_Release Shortcut Getting Starte
18. ton 3 Adjust the value of the adjustment items by pressing the Up or Down button 4 With the OSD menu on screen press Menu button to return main menu or exit OSD 5 The OSD menu will automatically close if you have left it idle for a pre set time 6 To Lock the OSD Power menu buttons please follow the instructions below Please note the monitor has to be turned ON with a valid signal pre set a Press Menu key the OSD menu will pops upon display b Press and hold the Menu key again with the OSD menu on the screen the OSD menu will disappear Then press the Power key 1 time while the menu key is still being pressed The Lock Unlock menu will appear for 3 seconds c Use the Enter key to select OSD or Power setting then set at Lock by pushing the UP or Down button d When the UP or Down button is released the previous setting will be saved and exit the Lock Unlock menu automatically 7 To Unlock the OSD Power menu buttons please follow the instructions below Please note the monitor has to be turned ON with a valid signal pre set a Press and hold the Menu key then press the Power key simultaneously the Lock Unlock menu will appear for 3 seconds b Use the Enter key to select OSD or Power setting then set at Unlock by pushing the UP or Down button c When the UP or Dow
19. tronic waste that can be hazardous if not disposed of properly Recycle or dispose in accordance with local state or federal laws For more information contact the Electronic Industries Alliance at WWW EIAE ORG For lamp specific disposal information check WWW LAMPRECYCLE ORG For more information on how to recycle your product please visit WWW PLANAR COM GREEN Table of Contents Usage Notice 1 Introduction About PT P54 5 RIP 1545L EEN 2 Touch Screen for PT 154 SR icsccsswerussacvincetdrvcacvsawsseuanstanipnswntainned tadesustanteneeibeetdwaeineamsaneenwswam 3 Touch Screen for PT 154 SP ck dccwietsctsdinaveinnsdiavcdviensddeucadieasiiaatied dtadewinedsathainueinniieeusdduadudiaccvar 3 4 Installation Product Overvi W e uran rr nuran u ranana anA ALARLAR LERA LAA ELARRE REAA Lannan aranna ne 5 Deet TEE 5 02 15451 Bottom Ate En e KEEN 5 1545 Bottom View Without Stand EE 5 Start en E UE a EE D Connecting the Display Figure e E 7 2222 2 22 2 2 2 2 2 22 2 222 22 _ _____ 8 EIERE Ee Fi Te er 9 VESA Mount Your Monitor 10 VM9 M 9MV 11 User Controls elie e Klee TT 12 E 13 On Screen Display Menus sese eee eee 14 Appendix RS IN
20. y refer to the following If the problem persists please contact your local dealer or our service center Problem No image appears on screen gt Check that all the I O and power connectors are correctly and well connected described in the Installation section gt Make sure the pins of the connectors are not crooked or broken Problem Partial Image or incorrectly displayed image Check to see if the resolution of your computer is higher than that of the display gt Reconfigure the resolution of your computer to make it less than or equal to 1024 x 768 Problem Image has vertical flickering line bars Use Fine to make an adjustment Check and reconfigure the display mode of the vertical refresh rate of your graphic card to make it compatible with the display Problem Image is unstable and flickering Use Horizontal size to make an adjustment Problem Image is scrolling gt Check and make sure the VGA signal cable or adapter is securely connected Check and reconfigure the display mode of the vertical refresh rate of your graphics card to make it compatible with the display Problem Vague image characters and graphics gt Use Fine to make an adjustment If this problem still exists use Horizontal size to make an adjustment Warning Signal II you see warning messages on your screen this means that the display cannot receive a clean signal from the computer graphics card Below
Download Pdf Manuals
Related Search